This document summarizes a vehicle theft detection and tracking system that uses GPS and GSM technologies. The system continuously monitors the location of a vehicle using GPS and reports it to an authorized user via GSM upon request or if theft is detected. When theft is detected, the user can send an SMS message to stop the vehicle engine. To restart the engine, the authorized user must send a password to the microcontroller via SMS. This provides secure, reliable, and low-cost vehicle tracking and theft prevention.
IRJET- GSM & GPS Based Vehicle Theft Control SystemIRJET Journal
This document describes a vehicle theft control system that uses GPS and GSM technologies. The system continuously tracks the location of a vehicle using a GPS modem and sends status updates via GSM. If theft is detected, the system sends an SMS alert with the vehicle's coordinates and disables the ignition. The owner can then send a password by SMS to restart the ignition and unlock doors remotely. The system aims to provide secure, reliable and low-cost vehicle tracking and theft prevention.
Microcontroller based automatic engine locking system for drunken driversVinny Chweety
This document describes a mini project report on a microcontroller-based automatic engine locking system for drunken drivers. The system uses an AT89S52 microcontroller and various hardware components like an alcohol detection sensor, buzzer, LCD display, motors/engine, and other supporting circuitry. If the alcohol detection sensor detects alcohol levels above a set limit from the driver's breath, the microcontroller will lock the engine by activating a relay to prevent drunken driving and accidents. The project aims to increase road safety by preventing intoxicated individuals from operating vehicles.
Electronics Notice Board Notice board using Wi-Fi ReportVaibhav Pandey
This document describes an electronic notice board project using Wi-Fi technology. The notice board displays messages on a matrix LED display that are sent wirelessly from a mobile phone. The system includes an Arduino Uno microcontroller, ESP8266 Wi-Fi module to receive messages, EEPROM memory to store character data, and a control unit to sequentially select the LED matrices. Messages can be changed remotely using a phone, providing flexible control without needing to access the display directly. The project allows for wireless information sharing across various public applications.
This document describes an automated railway gate controller project that uses infrared transmitters and receivers to automatically open and close railway gates based on the presence of an approaching train. When the train approaches the first reference point, the gate closes, and when the train passes the second reference point, the gate opens. The system utilizes amplitude shift keying modulation at 434MHz and a baud rate of 4800bps. An AT89S8253 microcontroller controls an IR transmitter LED and receiver to open and close the gate motor as trains pass through. The system aims to eliminate human error at unmanned railway crossings and reduce accidents.
This project aims to develop an automatic railway gate control system using sensors and microcontrollers to prevent accidents. The system uses IR sensors to detect approaching trains and automatically opens and closes railway gates. An Arduino board controls DC motors connected to the gates using an L293D motor driver chip. When a train is detected, the gate closes to stop road traffic and prevent collisions at unmanned level crossings. The automatic system eliminates human errors and provides reliable operation without requiring constant human monitoring.
The work is aimed at measurement of heartbeat and displays the information on an alphanumeric (or Graphical) LCD display. The heartbeat monitor uses LED and an LDR based sensor to determine the heartbeat.
IRJET- GSM & GPS Based Vehicle Theft Control SystemIRJET Journal
This document describes a vehicle theft control system that uses GPS and GSM technologies. The system continuously tracks the location of a vehicle using a GPS modem and sends status updates via GSM. If theft is detected, the system sends an SMS alert with the vehicle's coordinates and disables the ignition. The owner can then send a password by SMS to restart the ignition and unlock doors remotely. The system aims to provide secure, reliable and low-cost vehicle tracking and theft prevention.
Microcontroller based automatic engine locking system for drunken driversVinny Chweety
This document describes a mini project report on a microcontroller-based automatic engine locking system for drunken drivers. The system uses an AT89S52 microcontroller and various hardware components like an alcohol detection sensor, buzzer, LCD display, motors/engine, and other supporting circuitry. If the alcohol detection sensor detects alcohol levels above a set limit from the driver's breath, the microcontroller will lock the engine by activating a relay to prevent drunken driving and accidents. The project aims to increase road safety by preventing intoxicated individuals from operating vehicles.
Electronics Notice Board Notice board using Wi-Fi ReportVaibhav Pandey
This document describes an electronic notice board project using Wi-Fi technology. The notice board displays messages on a matrix LED display that are sent wirelessly from a mobile phone. The system includes an Arduino Uno microcontroller, ESP8266 Wi-Fi module to receive messages, EEPROM memory to store character data, and a control unit to sequentially select the LED matrices. Messages can be changed remotely using a phone, providing flexible control without needing to access the display directly. The project allows for wireless information sharing across various public applications.
This document describes an automated railway gate controller project that uses infrared transmitters and receivers to automatically open and close railway gates based on the presence of an approaching train. When the train approaches the first reference point, the gate closes, and when the train passes the second reference point, the gate opens. The system utilizes amplitude shift keying modulation at 434MHz and a baud rate of 4800bps. An AT89S8253 microcontroller controls an IR transmitter LED and receiver to open and close the gate motor as trains pass through. The system aims to eliminate human error at unmanned railway crossings and reduce accidents.
This project aims to develop an automatic railway gate control system using sensors and microcontrollers to prevent accidents. The system uses IR sensors to detect approaching trains and automatically opens and closes railway gates. An Arduino board controls DC motors connected to the gates using an L293D motor driver chip. When a train is detected, the gate closes to stop road traffic and prevent collisions at unmanned level crossings. The automatic system eliminates human errors and provides reliable operation without requiring constant human monitoring.
The work is aimed at measurement of heartbeat and displays the information on an alphanumeric (or Graphical) LCD display. The heartbeat monitor uses LED and an LDR based sensor to determine the heartbeat.
This document proposes an automatic control system for unmanned railway gates using sensors to reduce accidents. The objectives are to decrease costs by automating gates and reducing accidents through automatic closure when trains approach. The methodology uses infrared sensors to detect approaching trains and microcontrollers to signal gate motors. When a train is sensed, the system checks for vehicles near the gate before closing it, and reopens the gate once the train passes. This system could automate gates at road-rail crossings in Pakistan to improve safety.
Automatic vehicle accident detection and messaging system using gsm and gps m...mahesh_rman
This document summarizes an automatic vehicle accident detection and messaging system using GSM and GPS technology. The system uses a microcontroller, GSM modem, and GPS modem to detect if an accident occurs and send an SMS message with the vehicle's location to alert contacts. Some key advantages are providing security while traveling by detecting accident locations and notifying others. The system could also be expanded to track stolen vehicles or interface with other vehicle security systems.
Electronic Notice Board Using Raspberry Pi and Android PhoneBrijender k
This project is about displaying the text messages sent by the user from his/her android phone from a remote place and the message is displayed on LCD/LED screen in kiosk mode using Raspberry Pi. Android is we client and Raspberry Pi acts a web server
With rapid development of economies, growth of aging population and the prevalence of chronic diseases across the world, there is an urgent need to find new ways to improve patient outcomes, increase access to care, and reduce the cost of medical care. A health care monitoring system is necessary to constantly monitor patient’s physiological parameters. The tele-medical system focuses on the measurement and evaluation of vital parameters e.g. temperature, electrocardiogram (ECG), heart rate variability, fall detection etc. This will enable doctors and care givers to observe patients without having to be physically present at their bedside, be it in the hospital or in their home.
Accident messaging system using GPS,GSM and MEMSJithin Prasad
This project aims to develop an accident messaging system using a MEMS sensor to detect vibrations during accidents, a GPS module to determine location, and a GSM modem to send messages with location to emergency contacts. It is composed of a PIC microcontroller interfaced with MEMS, GPS, and GSM modules. When an accident is detected by the MEMS sensor, the system will use the GPS module to get location coordinates and send an SMS message with location via the GSM modem to alert contacts and enable emergency response.
Vehicle anti theft tracking system based on internet of things Jyothsna Sridhar
As the number of urban vehicles are growing rapidly vehicle theft has become an important concern for all vehicle owners.
However present anti theft system lacks the tracking and monitoring system.
The vehicle anti theft tracking System based on Internet of things is proposed which can provide all round service to car owners.
IoT BASED VEHICLE TRACKING AND TRAFFIC SURVIELLENCE SYSTEMjohn solomon j
ii
ABSTRACT GPS is one of the technologies that are used in a huge number of applications today. One of the applications is tracking your vehicle and keeps regular monitoring on them. This tracking system can inform you the location and route travelled by vehicle, and that information can be observed from any other remote location. It also includes the web application that provides you exact location of target and the exact speed the vehicle is moving which is used to generate bills for over speeding automatically. This system enables us to track target in any weather conditions. This system uses GPS and Zigbee technologies. This includes the hardware part which comprises of GPS, Zigbee, ATmega microcontroller and software part is used for interfacing all the required modules and a web application is also developed at the client side and visualize data from IoT. Main objective is to design a system that can be easily installed and to provide platform for further enhancement. KEYWORDS GPS, ZigBee, Tracking System, IoT
iii
The document proposes an IOT based smart bus tracking system that uses sensors like cell tower signals and audio recordings instead of GPS to predict bus locations with high accuracy. A prototype was tested on campus shuttle buses and public buses in Singapore and London, achieving better prediction than GPS-based solutions. The system is generally available, energy efficient, and easy to deploy across cities.
This document describes an OTP based smart wireless lock system using Arduino Uno that was presented by a group of students. The system uses Bluetooth to send a one-time password from a mobile device to an Arduino/servo motor-controlled lock. If the correct password and OTP are entered, the lock will open, providing secure access. It aims to improve security over traditional keys and enhance access control with automated unlocking using a smartphone app and Bluetooth connectivity.
With advancement of technology things are becoming simpler and easier for us. Automatic systems are being preferred over manual system. This project puts forth the equipment which enables users to control their home appliances using their cellular phone. It shows the construction and working of the device to wirelessly control the home appliances based on GSM networking and AT89c52 microcontroller. Initially an authenticated signal is sent from the user’s cellular phone via Global System for Mobile Communication (GSM) network to equipment. This signal or code consists of the information about the function or action to be taken place i.e. what appliance should be turned off or turned on? The receiver phone receives the SMS message that is send from the user’s phone and then sends it to the GSM modem which in turn sends the output digital signal to the microcontroller. Then the microcontroller, based on the received signal, controls the different relays and triggers the required appliance.
Wireless Electronic Notice Board Using Voice Recognition.With the advent of advance technology nowadays, the wireless communication is proving its importance in each and every field of today’s era. This system deals with use of one such wireless technology. The proposed system is a combination of hardware as well as software. The main idea of the project is to develop an electronic notice board which will display the content entered by user’s voice in his mobile phone. This in turn will reduce the paper consumptions and wastage of time involved in conventional notice board.
In speech controlled electronic notice board is very friendly to user and can operate merely from a distance of 10 meters(approx). Here, installed application operates on Voice recognition concept which will be embedded in a microcontroller interfaced with Bluetooth device. Bluetooth wireless technology helps in communication area, and is the fastest growing fields within the wireless technologies.
This document proposes a smart IoT device for two-wheelers to prevent theft. The existing systems have drawbacks like constantly using energy to track vehicles. The proposed system uses a vibration sensor and switch to detect movement only in parking mode. It sends alerts to the user's phone with GPS coordinates if movement is detected. It connects to a cloud server through LPWA when in parking mode to detect movement and send alerts. This provides a low-cost, small device to detect theft and track vehicles using less energy.
In highly populated countries, people lose their lives because of accidents and poor emergency facilities every day. These lives could have been saved if medical facilities are provided at the right time. This thesis implies a system which is a solution to this drawback, when a vehicle meets with an accident immediately, accelerometer module detects the signal, and it is sent to the Arduino microcontroller programmed by C programming language. Arduino sends an alert message through the GSM module including the location to the police station or a rescue team. So the police can immediately trace the location through the GPS modem after receiving the information. LCD is used to display location message from GPS module. The system is simulated and practically designed by the use of required hardware components and the results are satisfied with the expectation. Yu Yu Mon Win | Moe Myint Aung | Thin Thin "Accident Detection System using Arduino Uno" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-5 , August 2019, URL: https://www.ijtsrd.com/papers/ijtsrd27840.pdfPaper URL: https://www.ijtsrd.com/computer-science/other/27840/accident-detection-system-using-arduino-uno/yu-yu-mon-win
wireless electronics notice board using GSMRahul Kumar
The objective of this project is ‘We know the importance of notice boards in public places like railway stations and bus stations. But changing notices day-to-day,time to time is a difficult task. so explains how to design a wireless electronic notice board using GSM technology.
innovative railway track surveying with sensors and controlled by wireless co...kalaimathi mathiyazhagan
This document describes a proposed multi-sensor railway track geometry surveying system. The system uses MEMS, ultrasonic, and GPS sensors on a robot to detect cracks and obstacles on railway tracks and bridges in real-time. When issues are detected, the GPS location is recorded and an SMS is sent to authorities via GSM. Trains approaching will also receive a wireless message to slow down. A microcontroller controls gate closures to prevent accidents. The low-cost system aims to improve safety by allowing for faster response times over existing manual inspection methods.
This document presents information on vehicle tracking technology using GPS. It discusses how GPS works by receiving signals from satellites to determine location. It explains that GPS receivers can only receive location data and need another system like GSM cellular networks to send the location to a central control room. It provides details on GSM and GPRS cellular networks and how they enable communication of the vehicle location. It also discusses geographical information systems (GIS) software that can convert GPS coordinates to addresses. Finally, it presents information on some vehicle tracking devices that combine GPS and GSM technologies to track and monitor vehicles.
GPS GSM Based Vehicle Tracking & Locking SystemIRJET Journal
This document describes a GPS and GSM-based vehicle tracking and locking system created by five authors. The system uses a GPS receiver and SIM908 module to obtain a vehicle's location via satellites and send it via GSM networks. An ATmega16 microcontroller processes the location data, which is then sent as a text message to the vehicle's owner. The owner can lock the vehicle remotely by replying with the text "LOCK". The system provides low-cost vehicle tracking and anti-theft capabilities by allowing owners to monitor a vehicle's location and remotely immobilize it if stolen.
Tracking and Recovery of the Vehicle using GPS and GSMIRJET Journal
This document describes a vehicle tracking and recovery system that uses GPS and GSM technologies. The system includes sensors that detect accidents and send alerts. It uses a microcontroller connected to a GPS module and GSM modem to track the vehicle's location and send emergency SMS messages with the coordinates to emergency contacts when an accident is detected. The system aims to reduce accident fatalities by quickly notifying emergency services of accidents and the vehicle's location to facilitate rescue. It provides real-time vehicle tracking and recovery capabilities to increase road safety.
This document proposes an automatic control system for unmanned railway gates using sensors to reduce accidents. The objectives are to decrease costs by automating gates and reducing accidents through automatic closure when trains approach. The methodology uses infrared sensors to detect approaching trains and microcontrollers to signal gate motors. When a train is sensed, the system checks for vehicles near the gate before closing it, and reopens the gate once the train passes. This system could automate gates at road-rail crossings in Pakistan to improve safety.
Automatic vehicle accident detection and messaging system using gsm and gps m...mahesh_rman
This document summarizes an automatic vehicle accident detection and messaging system using GSM and GPS technology. The system uses a microcontroller, GSM modem, and GPS modem to detect if an accident occurs and send an SMS message with the vehicle's location to alert contacts. Some key advantages are providing security while traveling by detecting accident locations and notifying others. The system could also be expanded to track stolen vehicles or interface with other vehicle security systems.
Electronic Notice Board Using Raspberry Pi and Android PhoneBrijender k
This project is about displaying the text messages sent by the user from his/her android phone from a remote place and the message is displayed on LCD/LED screen in kiosk mode using Raspberry Pi. Android is we client and Raspberry Pi acts a web server
With rapid development of economies, growth of aging population and the prevalence of chronic diseases across the world, there is an urgent need to find new ways to improve patient outcomes, increase access to care, and reduce the cost of medical care. A health care monitoring system is necessary to constantly monitor patient’s physiological parameters. The tele-medical system focuses on the measurement and evaluation of vital parameters e.g. temperature, electrocardiogram (ECG), heart rate variability, fall detection etc. This will enable doctors and care givers to observe patients without having to be physically present at their bedside, be it in the hospital or in their home.
Accident messaging system using GPS,GSM and MEMSJithin Prasad
This project aims to develop an accident messaging system using a MEMS sensor to detect vibrations during accidents, a GPS module to determine location, and a GSM modem to send messages with location to emergency contacts. It is composed of a PIC microcontroller interfaced with MEMS, GPS, and GSM modules. When an accident is detected by the MEMS sensor, the system will use the GPS module to get location coordinates and send an SMS message with location via the GSM modem to alert contacts and enable emergency response.
Vehicle anti theft tracking system based on internet of things Jyothsna Sridhar
As the number of urban vehicles are growing rapidly vehicle theft has become an important concern for all vehicle owners.
However present anti theft system lacks the tracking and monitoring system.
The vehicle anti theft tracking System based on Internet of things is proposed which can provide all round service to car owners.
IoT BASED VEHICLE TRACKING AND TRAFFIC SURVIELLENCE SYSTEMjohn solomon j
ii
ABSTRACT GPS is one of the technologies that are used in a huge number of applications today. One of the applications is tracking your vehicle and keeps regular monitoring on them. This tracking system can inform you the location and route travelled by vehicle, and that information can be observed from any other remote location. It also includes the web application that provides you exact location of target and the exact speed the vehicle is moving which is used to generate bills for over speeding automatically. This system enables us to track target in any weather conditions. This system uses GPS and Zigbee technologies. This includes the hardware part which comprises of GPS, Zigbee, ATmega microcontroller and software part is used for interfacing all the required modules and a web application is also developed at the client side and visualize data from IoT. Main objective is to design a system that can be easily installed and to provide platform for further enhancement. KEYWORDS GPS, ZigBee, Tracking System, IoT
iii
The document proposes an IOT based smart bus tracking system that uses sensors like cell tower signals and audio recordings instead of GPS to predict bus locations with high accuracy. A prototype was tested on campus shuttle buses and public buses in Singapore and London, achieving better prediction than GPS-based solutions. The system is generally available, energy efficient, and easy to deploy across cities.
This document describes an OTP based smart wireless lock system using Arduino Uno that was presented by a group of students. The system uses Bluetooth to send a one-time password from a mobile device to an Arduino/servo motor-controlled lock. If the correct password and OTP are entered, the lock will open, providing secure access. It aims to improve security over traditional keys and enhance access control with automated unlocking using a smartphone app and Bluetooth connectivity.
With advancement of technology things are becoming simpler and easier for us. Automatic systems are being preferred over manual system. This project puts forth the equipment which enables users to control their home appliances using their cellular phone. It shows the construction and working of the device to wirelessly control the home appliances based on GSM networking and AT89c52 microcontroller. Initially an authenticated signal is sent from the user’s cellular phone via Global System for Mobile Communication (GSM) network to equipment. This signal or code consists of the information about the function or action to be taken place i.e. what appliance should be turned off or turned on? The receiver phone receives the SMS message that is send from the user’s phone and then sends it to the GSM modem which in turn sends the output digital signal to the microcontroller. Then the microcontroller, based on the received signal, controls the different relays and triggers the required appliance.
Wireless Electronic Notice Board Using Voice Recognition.With the advent of advance technology nowadays, the wireless communication is proving its importance in each and every field of today’s era. This system deals with use of one such wireless technology. The proposed system is a combination of hardware as well as software. The main idea of the project is to develop an electronic notice board which will display the content entered by user’s voice in his mobile phone. This in turn will reduce the paper consumptions and wastage of time involved in conventional notice board.
In speech controlled electronic notice board is very friendly to user and can operate merely from a distance of 10 meters(approx). Here, installed application operates on Voice recognition concept which will be embedded in a microcontroller interfaced with Bluetooth device. Bluetooth wireless technology helps in communication area, and is the fastest growing fields within the wireless technologies.
This document proposes a smart IoT device for two-wheelers to prevent theft. The existing systems have drawbacks like constantly using energy to track vehicles. The proposed system uses a vibration sensor and switch to detect movement only in parking mode. It sends alerts to the user's phone with GPS coordinates if movement is detected. It connects to a cloud server through LPWA when in parking mode to detect movement and send alerts. This provides a low-cost, small device to detect theft and track vehicles using less energy.
In highly populated countries, people lose their lives because of accidents and poor emergency facilities every day. These lives could have been saved if medical facilities are provided at the right time. This thesis implies a system which is a solution to this drawback, when a vehicle meets with an accident immediately, accelerometer module detects the signal, and it is sent to the Arduino microcontroller programmed by C programming language. Arduino sends an alert message through the GSM module including the location to the police station or a rescue team. So the police can immediately trace the location through the GPS modem after receiving the information. LCD is used to display location message from GPS module. The system is simulated and practically designed by the use of required hardware components and the results are satisfied with the expectation. Yu Yu Mon Win | Moe Myint Aung | Thin Thin "Accident Detection System using Arduino Uno" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-5 , August 2019, URL: https://www.ijtsrd.com/papers/ijtsrd27840.pdfPaper URL: https://www.ijtsrd.com/computer-science/other/27840/accident-detection-system-using-arduino-uno/yu-yu-mon-win
wireless electronics notice board using GSMRahul Kumar
The objective of this project is ‘We know the importance of notice boards in public places like railway stations and bus stations. But changing notices day-to-day,time to time is a difficult task. so explains how to design a wireless electronic notice board using GSM technology.
innovative railway track surveying with sensors and controlled by wireless co...kalaimathi mathiyazhagan
This document describes a proposed multi-sensor railway track geometry surveying system. The system uses MEMS, ultrasonic, and GPS sensors on a robot to detect cracks and obstacles on railway tracks and bridges in real-time. When issues are detected, the GPS location is recorded and an SMS is sent to authorities via GSM. Trains approaching will also receive a wireless message to slow down. A microcontroller controls gate closures to prevent accidents. The low-cost system aims to improve safety by allowing for faster response times over existing manual inspection methods.
This document presents information on vehicle tracking technology using GPS. It discusses how GPS works by receiving signals from satellites to determine location. It explains that GPS receivers can only receive location data and need another system like GSM cellular networks to send the location to a central control room. It provides details on GSM and GPRS cellular networks and how they enable communication of the vehicle location. It also discusses geographical information systems (GIS) software that can convert GPS coordinates to addresses. Finally, it presents information on some vehicle tracking devices that combine GPS and GSM technologies to track and monitor vehicles.
GPS GSM Based Vehicle Tracking & Locking SystemIRJET Journal
This document describes a GPS and GSM-based vehicle tracking and locking system created by five authors. The system uses a GPS receiver and SIM908 module to obtain a vehicle's location via satellites and send it via GSM networks. An ATmega16 microcontroller processes the location data, which is then sent as a text message to the vehicle's owner. The owner can lock the vehicle remotely by replying with the text "LOCK". The system provides low-cost vehicle tracking and anti-theft capabilities by allowing owners to monitor a vehicle's location and remotely immobilize it if stolen.
Tracking and Recovery of the Vehicle using GPS and GSMIRJET Journal
This document describes a vehicle tracking and recovery system that uses GPS and GSM technologies. The system includes sensors that detect accidents and send alerts. It uses a microcontroller connected to a GPS module and GSM modem to track the vehicle's location and send emergency SMS messages with the coordinates to emergency contacts when an accident is detected. The system aims to reduce accident fatalities by quickly notifying emergency services of accidents and the vehicle's location to facilitate rescue. It provides real-time vehicle tracking and recovery capabilities to increase road safety.
IRJET- Vehicle Accident Detection System using GSM and GPSIRJET Journal
This document describes a vehicle accident detection system that uses a microcontroller along with sensors like an accelerometer, GPS, and GSM modules. When an accident occurs, the accelerometer detects vibrations and sends a signal to the microcontroller. The microcontroller then uses the GPS module to get the location coordinates and sends an alert message with the coordinates via the GSM module to emergency contacts. This helps reduce response times and locate accidents quickly to provide faster medical assistance, potentially saving lives. The system is intended to automatically detect accidents and alert help unless manually overridden by the driver if assistance is not needed.
IRJET- Vehicle Starting using Fingerprint Sensor & Accident Detection using G...IRJET Journal
This document describes a vehicle security system that uses fingerprint authentication to start the vehicle. It also uses GPS and GSM technologies to track the vehicle's location and send an alert if an accident is detected. The system is designed to be low-cost compared to commercial options. It stores fingerprint data to only allow authorized users to start the vehicle. If an accident occurs, the exact location is sent via text message to emergency contacts, the police and an ambulance to help respond quickly. The system aims to reduce vehicle theft and improve response time in crash situations.
This document describes a smart vehicle tracking system using GPS. The system uses a GPS module to determine the location of the vehicle and send it via GSM to an Android application. A PIC18F4520 microcontroller interfaces with the GPS and GSM modules. The system allows users to track vehicles in real-time on their phones for safety and fleet management purposes. It also includes features like automated student attendance tracking on school buses using RFID tags.
A vehicle tracking system is very useful for tracking the movement of a vehicle from any location at any time. An efficient vehicle tracking system is designed and implemented for tracking the movement of any equipped vehicle from any location at any time. The proposed system made good use of popular technology that combines a smartphone with an Arduino UNO. This easy to make and inexpensive compared to others. The designed in vehicle device works using Global Positioning System GPS and Global System for Mobile Communication GSM technology that is one of the most common ways for vehicle tracking. The device is embedded inside a vehicle those positions is to be determined and tracked in real time. An Arduino UNO is used to control the GPS receiver and GSM module. The vehicle tracking system uses the GPS module to get geographic coordinates at regular time interval. The GSM module is used to transmit and update the vehicle location to a database. This paper gives minute by minute update about vehicle location by sending SMS through GSM modem. This SMS contain latitude and longitude of the location of vehicle. Arduino UNO gets the coordinates from GPS modem and then it sends this information to user in text SMS. GSM modem is used to send this information via SMS sent to the owner of the vehicle. Location is displayed on LCD. And then Google map displays location and name of the place on cell phone. Thus, user able to continuously monitor a moving vehicle on demand using smartphone and determine the estimated distance and time for the vehicle to arrive at a given destination. Ni Ni San Hlaing | Ma Naing | San San Naing ""GPS and GSM Based Vehicle Tracking System"" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-4 , June 2019, URL: https://www.ijtsrd.com/papers/ijtsrd23718.pdf
Paper URL: https://www.ijtsrd.com/engineering/electronics-and-communication-engineering/23718/gps-and-gsm-based-vehicle-tracking-system/ni-ni-san-hlaing
This document proposes a vehicle tracking and monitoring system using wireless technology like GPS and GSM to provide security, safety, and fleet management. The system tracks the vehicle's location through GPS and sends alerts by SMS. It also detects driver drowsiness using IR sensors and alerts the user, potentially slowing the vehicle. Additionally, it alerts users if they run a red traffic light based on RF sensors. The system aims to reduce costs and manpower needs for vehicle tracking while improving safety.
IJRET-V1I1P4 - Vehicle Tracking System Using GPS Tracking MethodISAR Publications
A vehicle tracking system is an electronic device installed in a vehicle to enable the owner
or a third party to track the vehicle's location.Multi-tracking system is a real time tracking platform
which uses integration of technologies such as GPS.The device installed in the vehicle
continuously moves and other related information at each position and then transmit to tracking
server, thus storing it in the database. Currently almost of the public having an own vehicle, theft is
happening on parking and sometimes driving insecurity places. The safe of vehicles is extremely
essential for public vehicles. As more devices become GPS enabled, accuracy will increase and the
system's scale and global reach will benefit everyone. Wireless technology promises to be a key
element in any long-term solution. This design will continuously monitor a moving Vehicle and
report the status of the Vehicle on demand
Keywords — GPS Tracking System, Vehicle Tracker , Security System .
IRJET- Intelligence Transportation System based on IoTIRJET Journal
This document describes an intelligent transportation system that detects vehicle accidents and notifies emergency services. It uses sensors in vehicles to detect accidents and send location information via GSM to ambulances and a server. An Android app allows ambulance drivers to control traffic lights to pass through more efficiently on their way to the accident site. Temperature sensors update patient condition to a hospital webpage. The system aims to reduce emergency response times, which can save lives when injuries occur in accidents. It presents the system architecture and algorithm for automatic accident detection and notification to provide faster emergency assistance.
IRJET- Wireless System for Vehicle Accident Detection and Reporting Using GPSIRJET Journal
1) The document describes a wireless system to detect vehicle accidents using an accelerometer sensor and GPS technology.
2) When an accident occurs, the accelerometer sensor detects the impact and sends a signal to an Arduino microcontroller.
3) The microcontroller then sends an alert message via GSM modem including the location from the GPS modem to emergency services, police, and family members. This allows emergency responders to quickly locate the accident site.
IRJET- GPS Tracker & Alcohol Detector with Engine Locking System using GSMIRJET Journal
This document describes a GPS tracker and alcohol detector system with engine locking capabilities using GSM. The system uses an alcohol sensor to detect if the driver has been drinking. If alcohol is detected, the sensor will send a signal to a microcontroller which will then send a message via GSM to a preregistered mobile number. The message alerts that the driver is drunk. An alarm will sound in the car and the engine will lock. The GPS module tracks the car's location using longitude and latitude, which is sent via GSM to the user's phone. This allows the owner to view the car's location on Google Maps. The system aims to prevent drunk driving accidents.
IRJET- Modelling of Recycle Plant for Construction and Demolition WasteIRJET Journal
This document describes a vehicle monitoring system that uses sensors, a microcontroller, GPS, and GSM to track the location and fuel level of a vehicle and send notifications to an owner's mobile phone. The system includes sensors attached to a thin rod that is inserted into the vehicle's fuel tank to detect the fuel level. The microcontroller processes this sensor data along with location information from the GPS. It then sends text messages with the fuel level and location to a specified mobile number via the GSM modem. The system is powered by a battery and aims to inform owners about the vehicle's status and location in real-time.
IRJET- Smart Vehicle with Crash Detection and Emergency Vehicle Dispatch with...IRJET Journal
This document describes a smart vehicle system that detects vehicle crashes and dispatches emergency services. The system has two main parts: 1) crash detection and location identification, and 2) efficient traffic control for emergency vehicles. The first part uses sensors to detect crashes and obtain location and passenger health data from GPS and pulse sensors, sending this information via GSM to emergency services. The second part uses RFID to control traffic signals and prioritize lanes for approaching emergency response vehicles to reach the crash site more quickly. The overall goal is to minimize response times and reduce transportation accident deaths.
IRJET- Automatic Vehicle Accident Detection and Rescue SystemIRJET Journal
This document describes an automatic vehicle accident detection and rescue system that uses IoT technology. The system uses impact and ultrasonic sensors to detect if an accident occurs. If an accident is detected, the Arduino microcontroller sends the vehicle's location data from the GPS module and alerts the vehicle owner, nearest hospital, and police station through text messages sent via a GSM modem. The goal is to detect accidents quickly and send location information to emergency responders to reduce loss of life. The system aims to automatically detect accidents and communicate location information faster than existing systems to improve emergency response times.
IRJET - Accident Monitoring and Rescue SystemIRJET Journal
This document describes a proposed accident monitoring and rescue system using IoT technologies. The system uses sensors like an accelerometer and GPS module embedded on a CC3200 microcontroller board to detect if an accident occurs. If a hard impact is detected by a change in acceleration beyond a threshold, the GPS location, temperature readings, and accelerometer values would be sent as an SMS using cloud services like Twilio to alert emergency contacts and services. The goal is to help rescue victims and reduce response times in the event of a road accident.
This document describes a smart car anti-theft system that uses IoT technology. The system uses a vibration sensor to detect if someone is trying to break into the car. It then sends SMS, email, and push notifications to the owner's phone using an ESP8266 WiFi module. It also triggers an alarm in the car. If the car is stolen, the in-built GPS system can track its location. The system is compact and affordable. It aims to provide higher security and response times than traditional car alarm systems through multi-layered alerts and GPS tracking without extra hardware.
IRJET- Vehicle Security System using IoT ApplicationIRJET Journal
1. The document describes a vehicle security system that uses IoT technology to prevent vehicle theft. It uses sensors to detect vibrations if someone tries to steal the vehicle. It then sends a signal to a microcontroller and sends an SMS alert to the owner.
2. The owner can then log into an IoT-based web server to track the vehicle's location using GPS and control the vehicle remotely by activating features like honking or stopping the engine.
3. The system aims to provide affordable vehicle security and alerts the owner via SMS if the vehicle is being stolen whether they are near or far from the vehicle using technologies like sensors, microcontrollers, GPS and GSM communication.
IRJET-Automatic Vehicle Accident Detection and Messaging System using GSM and...IRJET Journal
This document describes an automatic vehicle accident detection and messaging system using GPS and GSM technology. The system uses a sensor to detect if a vehicle has been in an accident. If an accident is detected, the sensor notifies a microcontroller which then sends an alert message with the vehicle's location (determined by GPS) to emergency contacts via GSM. This is done to notify authorities and loved ones of the accident quickly in order to save lives. The system provides accident detection and location services to help emergency responders arrive faster when seconds matter most.
Automatic Car Theft Detection System Based on GPS and GSM Technologyijtsrd
An efficient automotive security system is implemented for anti theft using an embedded system integrated with Global Positioning System GPS and Global System for Mobile Communication GSM. System presented has Two types of tracking, one is online tracking with GPS system can only receive the vehicle location information from satellites and other is offline tracking. GSM system is installed in the vehicle for sending the information to the owner of the vehicle. The preventive measures like engine ignition cutoff is installed in the vehicle which is controlled using user or owner GSM mobile. The owner can lock or unlock his her vehicle with the help of SMS. The system is implemented on general purpose printed circuit board PCB Using Arduino. Sandeep Singh | Poonam Kumari ""Automatic Car Theft Detection System Based on GPS and GSM Technology"" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-4 , June 2019, URL: https://www.ijtsrd.com/papers/ijtsrd23867.pdf
Paper URL: https://www.ijtsrd.com/engineering/electronics-and-communication-engineering/23867/automatic-car-theft-detection-system-based-on-gps-and-gsm-technology/sandeep-singh
IRJET- Implementation of Automated Toll System for Highways and BridgesIRJET Journal
The document proposes an automated toll system for highways and bridges using RFID and GSM technology to reduce traffic congestion. The system uses RFID tags attached to vehicles to identify them and deduct toll charges automatically from a linked account if there are sufficient funds. If not, the driver can add money using a mobile app. It sends transaction messages to the user via SMS. The system aims to streamline the toll payment process and improve traffic flow compared to manual systems. It discusses the components used like RFID readers, Arduino microcontroller, servo motors and GSM modem along with the working flowchart. The proposed automated system offers benefits like time savings, reduced congestion and a smoother toll passage process overall.
Similar to Vehicle Theft Detection and Tracking Based on GSM and GPS (20)
TUNNELING IN HIMALAYAS WITH NATM METHOD: A SPECIAL REFERENCES TO SUNGAL TUNNE...IRJET Journal
1) The document discusses the Sungal Tunnel project in Jammu and Kashmir, India, which is being constructed using the New Austrian Tunneling Method (NATM).
2) NATM involves continuous monitoring during construction to adapt to changing ground conditions, and makes extensive use of shotcrete for temporary tunnel support.
3) The methodology section outlines the systematic geotechnical design process for tunnels according to Austrian guidelines, and describes the various steps of NATM tunnel construction including initial and secondary tunnel support.
STUDY THE EFFECT OF RESPONSE REDUCTION FACTOR ON RC FRAMED STRUCTUREIRJET Journal
This study examines the effect of response reduction factors (R factors) on reinforced concrete (RC) framed structures through nonlinear dynamic analysis. Three RC frame models with varying heights (4, 8, and 12 stories) were analyzed in ETABS software under different R factors ranging from 1 to 5. The results showed that displacement increased as the R factor decreased, indicating less linear behavior for lower R factors. Drift also decreased proportionally with increasing R factors from 1 to 5. Shear forces in the frames decreased with higher R factors. In general, R factors of 3 to 5 produced more satisfactory performance with less displacement and drift. The displacement variations between different building heights were consistent at different R factors. This study evaluated how R factors influence
A COMPARATIVE ANALYSIS OF RCC ELEMENT OF SLAB WITH STARK STEEL (HYSD STEEL) A...IRJET Journal
This study compares the use of Stark Steel and TMT Steel as reinforcement materials in a two-way reinforced concrete slab. Mechanical testing is conducted to determine the tensile strength, yield strength, and other properties of each material. A two-way slab design adhering to codes and standards is executed with both materials. The performance is analyzed in terms of deflection, stability under loads, and displacement. Cost analyses accounting for material, durability, maintenance, and life cycle costs are also conducted. The findings provide insights into the economic and structural implications of each material for reinforcement selection and recommendations on the most suitable material based on the analysis.
Effect of Camber and Angles of Attack on Airfoil CharacteristicsIRJET Journal
This document discusses a study analyzing the effect of camber, position of camber, and angle of attack on the aerodynamic characteristics of airfoils. Sixteen modified asymmetric NACA airfoils were analyzed using computational fluid dynamics (CFD) by varying the camber, camber position, and angle of attack. The results showed the relationship between these parameters and the lift coefficient, drag coefficient, and lift to drag ratio. This provides insight into how changes in airfoil geometry impact aerodynamic performance.
A Review on the Progress and Challenges of Aluminum-Based Metal Matrix Compos...IRJET Journal
This document reviews the progress and challenges of aluminum-based metal matrix composites (MMCs), focusing on their fabrication processes and applications. It discusses how various aluminum MMCs have been developed using reinforcements like borides, carbides, oxides, and nitrides to improve mechanical and wear properties. These composites have gained prominence for their lightweight, high-strength and corrosion resistance properties. The document also examines recent advancements in fabrication techniques for aluminum MMCs and their growing applications in industries such as aerospace and automotive. However, it notes that challenges remain around issues like improper mixing of reinforcements and reducing reinforcement agglomeration.
Dynamic Urban Transit Optimization: A Graph Neural Network Approach for Real-...IRJET Journal
This document discusses research on using graph neural networks (GNNs) for dynamic optimization of public transportation networks in real-time. GNNs represent transit networks as graphs with nodes as stops and edges as connections. The GNN model aims to optimize networks using real-time data on vehicle locations, arrival times, and passenger loads. This helps increase mobility, decrease traffic, and improve efficiency. The system continuously trains and infers to adapt to changing transit conditions, providing decision support tools. While research has focused on performance, more work is needed on security, socio-economic impacts, contextual generalization of models, continuous learning approaches, and effective real-time visualization.
Structural Analysis and Design of Multi-Storey Symmetric and Asymmetric Shape...IRJET Journal
This document summarizes a research project that aims to compare the structural performance of conventional slab and grid slab systems in multi-story buildings using ETABS software. The study will analyze both symmetric and asymmetric building models under various loading conditions. Parameters like deflections, moments, shears, and stresses will be examined to evaluate the structural effectiveness of each slab type. The results will provide insights into the comparative behavior of conventional and grid slabs to help engineers and architects select appropriate slab systems based on building layouts and design requirements.
A Review of “Seismic Response of RC Structures Having Plan and Vertical Irreg...IRJET Journal
This document summarizes and reviews a research paper on the seismic response of reinforced concrete (RC) structures with plan and vertical irregularities, with and without infill walls. It discusses how infill walls can improve or reduce the seismic performance of RC buildings, depending on factors like wall layout, height distribution, connection to the frame, and relative stiffness of walls and frames. The reviewed research paper analyzes the behavior of infill walls, effects of vertical irregularities, and seismic performance of high-rise structures under linear static and dynamic analysis. It studies response characteristics like story drift, deflection and shear. The document also provides literature on similar research investigating the effects of infill walls, soft stories, plan irregularities, and different
This document provides a review of machine learning techniques used in Advanced Driver Assistance Systems (ADAS). It begins with an abstract that summarizes key applications of machine learning in ADAS, including object detection, recognition, and decision-making. The introduction discusses the integration of machine learning in ADAS and how it is transforming vehicle safety. The literature review then examines several research papers on topics like lightweight deep learning models for object detection and lane detection models using image processing. It concludes by discussing challenges and opportunities in the field, such as improving algorithm robustness and adaptability.
Long Term Trend Analysis of Precipitation and Temperature for Asosa district,...IRJET Journal
The document analyzes temperature and precipitation trends in Asosa District, Benishangul Gumuz Region, Ethiopia from 1993 to 2022 based on data from the local meteorological station. The results show:
1) The average maximum and minimum annual temperatures have generally decreased over time, with maximum temperatures decreasing by a factor of -0.0341 and minimum by -0.0152.
2) Mann-Kendall tests found the decreasing temperature trends to be statistically significant for annual maximum temperatures but not for annual minimum temperatures.
3) Annual precipitation in Asosa District showed a statistically significant increasing trend.
The conclusions recommend development planners account for rising summer precipitation and declining temperatures in
P.E.B. Framed Structure Design and Analysis Using STAAD ProIRJET Journal
This document discusses the design and analysis of pre-engineered building (PEB) framed structures using STAAD Pro software. It provides an overview of PEBs, including that they are designed off-site with building trusses and beams produced in a factory. STAAD Pro is identified as a key tool for modeling, analyzing, and designing PEBs to ensure their performance and safety under various load scenarios. The document outlines modeling structural parts in STAAD Pro, evaluating structural reactions, assigning loads, and following international design codes and standards. In summary, STAAD Pro is used to design and analyze PEB framed structures to ensure safety and code compliance.
A Review on Innovative Fiber Integration for Enhanced Reinforcement of Concre...IRJET Journal
This document provides a review of research on innovative fiber integration methods for reinforcing concrete structures. It discusses studies that have explored using carbon fiber reinforced polymer (CFRP) composites with recycled plastic aggregates to develop more sustainable strengthening techniques. It also examines using ultra-high performance fiber reinforced concrete to improve shear strength in beams. Additional topics covered include the dynamic responses of FRP-strengthened beams under static and impact loads, and the performance of preloaded CFRP-strengthened fiber reinforced concrete beams. The review highlights the potential of fiber composites to enable more sustainable and resilient construction practices.
Survey Paper on Cloud-Based Secured Healthcare SystemIRJET Journal
This document summarizes a survey on securing patient healthcare data in cloud-based systems. It discusses using technologies like facial recognition, smart cards, and cloud computing combined with strong encryption to securely store patient data. The survey found that healthcare professionals believe digitizing patient records and storing them in a centralized cloud system would improve access during emergencies and enable more efficient care compared to paper-based systems. However, ensuring privacy and security of patient data is paramount as healthcare incorporates these digital technologies.
Review on studies and research on widening of existing concrete bridgesIRJET Journal
This document summarizes several studies that have been conducted on widening existing concrete bridges. It describes a study from China that examined load distribution factors for a bridge widened with composite steel-concrete girders. It also outlines challenges and solutions for widening a bridge in the UAE, including replacing bearings and stitching the new and existing structures. Additionally, it discusses two bridge widening projects in New Zealand that involved adding precast beams and stitching to connect structures. Finally, safety measures and challenges for strengthening a historic bridge in Switzerland under live traffic are presented.
React based fullstack edtech web applicationIRJET Journal
The document describes the architecture of an educational technology web application built using the MERN stack. It discusses the frontend developed with ReactJS, backend with NodeJS and ExpressJS, and MongoDB database. The frontend provides dynamic user interfaces, while the backend offers APIs for authentication, course management, and other functions. MongoDB enables flexible data storage. The architecture aims to provide a scalable, responsive platform for online learning.
A Comprehensive Review of Integrating IoT and Blockchain Technologies in the ...IRJET Journal
This paper proposes integrating Internet of Things (IoT) and blockchain technologies to help implement objectives of India's National Education Policy (NEP) in the education sector. The paper discusses how blockchain could be used for secure student data management, credential verification, and decentralized learning platforms. IoT devices could create smart classrooms, automate attendance tracking, and enable real-time monitoring. Blockchain would ensure integrity of exam processes and resource allocation, while smart contracts automate agreements. The paper argues this integration has potential to revolutionize education by making it more secure, transparent and efficient, in alignment with NEP goals. However, challenges like infrastructure needs, data privacy, and collaborative efforts are also discussed.
A REVIEW ON THE PERFORMANCE OF COCONUT FIBRE REINFORCED CONCRETE.IRJET Journal
This document provides a review of research on the performance of coconut fibre reinforced concrete. It summarizes several studies that tested different volume fractions and lengths of coconut fibres in concrete mixtures with varying compressive strengths. The studies found that coconut fibre improved properties like tensile strength, toughness, crack resistance, and spalling resistance compared to plain concrete. Volume fractions of 2-5% and fibre lengths of 20-50mm produced the best results. The document concludes that using a 4-5% volume fraction of coconut fibres 30-40mm in length with M30-M60 grade concrete would provide benefits based on previous research.
Optimizing Business Management Process Workflows: The Dynamic Influence of Mi...IRJET Journal
The document discusses optimizing business management processes through automation using Microsoft Power Automate and artificial intelligence. It provides an overview of Power Automate's key components and features for automating workflows across various apps and services. The document then presents several scenarios applying automation solutions to common business processes like data entry, monitoring, HR, finance, customer support, and more. It estimates the potential time and cost savings from implementing automation for each scenario. Finally, the conclusion emphasizes the transformative impact of AI and automation tools on business processes and the need for ongoing optimization.
Multistoried and Multi Bay Steel Building Frame by using Seismic DesignIRJET Journal
The document describes the seismic design of a G+5 steel building frame located in Roorkee, India according to Indian codes IS 1893-2002 and IS 800. The frame was analyzed using the equivalent static load method and response spectrum method, and its response in terms of displacements and shear forces were compared. Based on the analysis, the frame was designed as a seismic-resistant steel structure according to IS 800:2007. The software STAAD Pro was used for the analysis and design.
Cost Optimization of Construction Using Plastic Waste as a Sustainable Constr...IRJET Journal
This research paper explores using plastic waste as a sustainable and cost-effective construction material. The study focuses on manufacturing pavers and bricks using recycled plastic and partially replacing concrete with plastic alternatives. Initial results found that pavers and bricks made from recycled plastic demonstrate comparable strength and durability to traditional materials while providing environmental and cost benefits. Additionally, preliminary research indicates incorporating plastic waste as a partial concrete replacement significantly reduces construction costs without compromising structural integrity. The outcomes suggest adopting plastic waste in construction can address plastic pollution while optimizing costs, promoting more sustainable building practices.
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...IJECEIAES
Climate change's impact on the planet forced the United Nations and governments to promote green energies and electric transportation. The deployments of photovoltaic (PV) and electric vehicle (EV) systems gained stronger momentum due to their numerous advantages over fossil fuel types. The advantages go beyond sustainability to reach financial support and stability. The work in this paper introduces the hybrid system between PV and EV to support industrial and commercial plants. This paper covers the theoretical framework of the proposed hybrid system including the required equation to complete the cost analysis when PV and EV are present. In addition, the proposed design diagram which sets the priorities and requirements of the system is presented. The proposed approach allows setup to advance their power stability, especially during power outages. The presented information supports researchers and plant owners to complete the necessary analysis while promoting the deployment of clean energy. The result of a case study that represents a dairy milk farmer supports the theoretical works and highlights its advanced benefits to existing plants. The short return on investment of the proposed approach supports the paper's novelty approach for the sustainable electrical system. In addition, the proposed system allows for an isolated power setup without the need for a transmission line which enhances the safety of the electrical network
Literature Review Basics and Understanding Reference Management.pptxDr Ramhari Poudyal
Three-day training on academic research focuses on analytical tools at United Technical College, supported by the University Grant Commission, Nepal. 24-26 May 2024
Using recycled concrete aggregates (RCA) for pavements is crucial to achieving sustainability. Implementing RCA for new pavement can minimize carbon footprint, conserve natural resources, reduce harmful emissions, and lower life cycle costs. Compared to natural aggregate (NA), RCA pavement has fewer comprehensive studies and sustainability assessments.
ACEP Magazine edition 4th launched on 05.06.2024Rahul
This document provides information about the third edition of the magazine "Sthapatya" published by the Association of Civil Engineers (Practicing) Aurangabad. It includes messages from current and past presidents of ACEP, memories and photos from past ACEP events, information on life time achievement awards given by ACEP, and a technical article on concrete maintenance, repairs and strengthening. The document highlights activities of ACEP and provides a technical educational article for members.
Using recycled concrete aggregates (RCA) for pavements is crucial to achieving sustainability. Implementing RCA for new pavement can minimize carbon footprint, conserve natural resources, reduce harmful emissions, and lower life cycle costs. Compared to natural aggregate (NA), RCA pavement has fewer comprehensive studies and sustainability assessments.
Embedded machine learning-based road conditions and driving behavior monitoringIJECEIAES
Car accident rates have increased in recent years, resulting in losses in human lives, properties, and other financial costs. An embedded machine learning-based system is developed to address this critical issue. The system can monitor road conditions, detect driving patterns, and identify aggressive driving behaviors. The system is based on neural networks trained on a comprehensive dataset of driving events, driving styles, and road conditions. The system effectively detects potential risks and helps mitigate the frequency and impact of accidents. The primary goal is to ensure the safety of drivers and vehicles. Collecting data involved gathering information on three key road events: normal street and normal drive, speed bumps, circular yellow speed bumps, and three aggressive driving actions: sudden start, sudden stop, and sudden entry. The gathered data is processed and analyzed using a machine learning system designed for limited power and memory devices. The developed system resulted in 91.9% accuracy, 93.6% precision, and 92% recall. The achieved inference time on an Arduino Nano 33 BLE Sense with a 32-bit CPU running at 64 MHz is 34 ms and requires 2.6 kB peak RAM and 139.9 kB program flash memory, making it suitable for resource-constrained embedded systems.
A review on techniques and modelling methodologies used for checking electrom...nooriasukmaningtyas
The proper function of the integrated circuit (IC) in an inhibiting electromagnetic environment has always been a serious concern throughout the decades of revolution in the world of electronics, from disjunct devices to today’s integrated circuit technology, where billions of transistors are combined on a single chip. The automotive industry and smart vehicles in particular, are confronting design issues such as being prone to electromagnetic interference (EMI). Electronic control devices calculate incorrect outputs because of EMI and sensors give misleading values which can prove fatal in case of automotives. In this paper, the authors have non exhaustively tried to review research work concerned with the investigation of EMI in ICs and prediction of this EMI using various modelling methodologies and measurement setups.
Comparative analysis between traditional aquaponics and reconstructed aquapon...bijceesjournal
The aquaponic system of planting is a method that does not require soil usage. It is a method that only needs water, fish, lava rocks (a substitute for soil), and plants. Aquaponic systems are sustainable and environmentally friendly. Its use not only helps to plant in small spaces but also helps reduce artificial chemical use and minimizes excess water use, as aquaponics consumes 90% less water than soil-based gardening. The study applied a descriptive and experimental design to assess and compare conventional and reconstructed aquaponic methods for reproducing tomatoes. The researchers created an observation checklist to determine the significant factors of the study. The study aims to determine the significant difference between traditional aquaponics and reconstructed aquaponics systems propagating tomatoes in terms of height, weight, girth, and number of fruits. The reconstructed aquaponics system’s higher growth yield results in a much more nourished crop than the traditional aquaponics system. It is superior in its number of fruits, height, weight, and girth measurement. Moreover, the reconstructed aquaponics system is proven to eliminate all the hindrances present in the traditional aquaponics system, which are overcrowding of fish, algae growth, pest problems, contaminated water, and dead fish.
Advanced control scheme of doubly fed induction generator for wind turbine us...IJECEIAES
This paper describes a speed control device for generating electrical energy on an electricity network based on the doubly fed induction generator (DFIG) used for wind power conversion systems. At first, a double-fed induction generator model was constructed. A control law is formulated to govern the flow of energy between the stator of a DFIG and the energy network using three types of controllers: proportional integral (PI), sliding mode controller (SMC) and second order sliding mode controller (SOSMC). Their different results in terms of power reference tracking, reaction to unexpected speed fluctuations, sensitivity to perturbations, and resilience against machine parameter alterations are compared. MATLAB/Simulink was used to conduct the simulations for the preceding study. Multiple simulations have shown very satisfying results, and the investigations demonstrate the efficacy and power-enhancing capabilities of the suggested control system.