Implementation of solar pv battery and diesel generator based electric vehic...Asoka Technologies
In this paper, a solar PV (Photovoltaic) array, a battery energy storage (BES), a diesel generator (DG) set and grid based EV charging station (CS) is utilized to provide the incessant charging in islanded, grid connected and DG set connected modes. The charging station is primarily designed to use the solar photovoltaic PV array and a BES to charge the electric vehicle (EV) battery. However, in case of exhausted storage battery and unavailable solar PV array generation, the charging station intelligently takes power from the grid or DG (Diesel Generator) set. However, the power from DG set is drawn in a manner that, it always operates at 80-85% loading to achieve maximum fuel efficiency under all loading conditions. Moreover, in coordination with the storage battery, the charging station regulates the generator voltage and frequency without a mechanical speed governor. It also ensures that the power drawn from the grid or the DG set is at unity power factor (UPF) even at nonlinear loading. Moreover, the PCC (Point of Common Coupling) voltage is synchronized to the grid/ generator voltage to obtain the ceaseless charging. The charging station also performs the vehicle to grid active/reactive power transfer, vehicle to home and vehicle to vehicle power transfer for increasing the operational efficiency of the charging station. The operation of the charging station is experimentally validated using the prototype developed in the laboratory.
Feasibility and optimal design of a hybrid power system for rural electrifica...IJECEIAES
A hybrid renewable energy system is at present accepted globally, as the best option for rural electrification particularly in areas where grid extension is infeasible. However, the need for hybrid design to be optimal in terms of operation and component selection serves as a challenge in obtaining reliable electricity at a minimum cost. In this work, the feasibility of installing a small hydropower into an existing water supply dam and the development of an optimal sizing optimization model for a small village-Itapaji, Nigeria were carried out. The developed hybrid power system (HPS) model consists of solar photovoltaic, small hydropower, battery and diesel generator. The optimal sizing of the system’s components for optimum configuration was carried out using Genetic Algorithm. The hybrid model’s results were compared with hybrid optimization model for electric renewable (HOMER) using correlation coefficient (r) and root mean square error (RMSE) to verify its validity. The results of the simulation obtained from the developed model showed better correlation coefficient (r) of 0.88 and root mean square error (RMSE) of 0.001 when compared to that of HOMER. This will serve as a guide for the power system engineers in the feasibility assessment and optimal design of HPS for rural electrification.
Planning and Designing a Stand Alone Solar Power System for Multi-Building Or...IJMER
The purpose of this project is to discover ways to produce energy with alternate sources. This presents current status, major achievements and future aspects of solar energy in India and evaluation of current energy policies for conquering the obstructions and implementing solar for the future is also been presented. Solar energy is expected to play a very significant role in the future especially in developing countries, but it has also potential prospects for developed countries. Solar radiation is an integral part of different renewable energy resources like PV power, solar thermal power, solar heater etc.
This consists of Study of the Solar cell, Solar Photovoltaic Technology, Planning and Designing a Stand Alone Solar Power System for Multi Building in an Organization where Solar energy plays an important role for the power supply in case of emergency by replacing Diesel Generator set i.e. DG Set.
This gives a detail planning and designing of solar power system of 80KW demand per hour for Al-Falah School of engineering and technology, Brown hills college of engineering and technology, central canteen, masjid, Hostel as well as Al-Falah School of Training and Education.
In Off-Grid solar power system, the battery is included for storage. Energy stored in this battery can be used as per requirement. A small scale diesel generator is also recommended for additional power in case of bad weather condition.
Power Management in PV-Battery-Hydro Based Standalone MicrogridAsoka Technologies
This paper proposes a high-efficiency two stage three-level grid-connected photovoltaic inverter. This work deals with the frequency regulation, voltage regulation, power management and load levelling of solar photovoltaic (PV)-battery-hydro based microgrid (MG). In this MG, the battery capacity is reduced as compared to a system, where the battery is directly connected to the DC bus of the voltage source converter (VSC). A bidirectional DC–DC converter connects the battery to the DC bus and it controls the charging and discharging current of the battery. It also regulates the DC bus voltage of VSC, frequency and voltage of MG. The proposed system manages the power flow of different sources like hydro and solar PV array. However, the load levelling is managed through the battery. The battery with VSC absorbs the sudden load changes, resulting in rapid regulation of DC link voltage, frequency and voltage of MG. Therefore, the system voltage and frequency regulation allows the active power balance along with the auxiliary services such as reactive power support, source current harmonics mitigation and voltage harmonics reduction at the point of common interconnection. The experimental results under various steady state and dynamic conditions, exhibit the excellent performance of the proposed system and validate the design and control of proposed MG.
Implementation of solar pv battery and diesel generator based electric vehic...Asoka Technologies
In this paper, a solar PV (Photovoltaic) array, a battery energy storage (BES), a diesel generator (DG) set and grid based EV charging station (CS) is utilized to provide the incessant charging in islanded, grid connected and DG set connected modes. The charging station is primarily designed to use the solar photovoltaic PV array and a BES to charge the electric vehicle (EV) battery. However, in case of exhausted storage battery and unavailable solar PV array generation, the charging station intelligently takes power from the grid or DG (Diesel Generator) set. However, the power from DG set is drawn in a manner that, it always operates at 80-85% loading to achieve maximum fuel efficiency under all loading conditions. Moreover, in coordination with the storage battery, the charging station regulates the generator voltage and frequency without a mechanical speed governor. It also ensures that the power drawn from the grid or the DG set is at unity power factor (UPF) even at nonlinear loading. Moreover, the PCC (Point of Common Coupling) voltage is synchronized to the grid/ generator voltage to obtain the ceaseless charging. The charging station also performs the vehicle to grid active/reactive power transfer, vehicle to home and vehicle to vehicle power transfer for increasing the operational efficiency of the charging station. The operation of the charging station is experimentally validated using the prototype developed in the laboratory.
Feasibility and optimal design of a hybrid power system for rural electrifica...IJECEIAES
A hybrid renewable energy system is at present accepted globally, as the best option for rural electrification particularly in areas where grid extension is infeasible. However, the need for hybrid design to be optimal in terms of operation and component selection serves as a challenge in obtaining reliable electricity at a minimum cost. In this work, the feasibility of installing a small hydropower into an existing water supply dam and the development of an optimal sizing optimization model for a small village-Itapaji, Nigeria were carried out. The developed hybrid power system (HPS) model consists of solar photovoltaic, small hydropower, battery and diesel generator. The optimal sizing of the system’s components for optimum configuration was carried out using Genetic Algorithm. The hybrid model’s results were compared with hybrid optimization model for electric renewable (HOMER) using correlation coefficient (r) and root mean square error (RMSE) to verify its validity. The results of the simulation obtained from the developed model showed better correlation coefficient (r) of 0.88 and root mean square error (RMSE) of 0.001 when compared to that of HOMER. This will serve as a guide for the power system engineers in the feasibility assessment and optimal design of HPS for rural electrification.
Planning and Designing a Stand Alone Solar Power System for Multi-Building Or...IJMER
The purpose of this project is to discover ways to produce energy with alternate sources. This presents current status, major achievements and future aspects of solar energy in India and evaluation of current energy policies for conquering the obstructions and implementing solar for the future is also been presented. Solar energy is expected to play a very significant role in the future especially in developing countries, but it has also potential prospects for developed countries. Solar radiation is an integral part of different renewable energy resources like PV power, solar thermal power, solar heater etc.
This consists of Study of the Solar cell, Solar Photovoltaic Technology, Planning and Designing a Stand Alone Solar Power System for Multi Building in an Organization where Solar energy plays an important role for the power supply in case of emergency by replacing Diesel Generator set i.e. DG Set.
This gives a detail planning and designing of solar power system of 80KW demand per hour for Al-Falah School of engineering and technology, Brown hills college of engineering and technology, central canteen, masjid, Hostel as well as Al-Falah School of Training and Education.
In Off-Grid solar power system, the battery is included for storage. Energy stored in this battery can be used as per requirement. A small scale diesel generator is also recommended for additional power in case of bad weather condition.
Power Management in PV-Battery-Hydro Based Standalone MicrogridAsoka Technologies
This paper proposes a high-efficiency two stage three-level grid-connected photovoltaic inverter. This work deals with the frequency regulation, voltage regulation, power management and load levelling of solar photovoltaic (PV)-battery-hydro based microgrid (MG). In this MG, the battery capacity is reduced as compared to a system, where the battery is directly connected to the DC bus of the voltage source converter (VSC). A bidirectional DC–DC converter connects the battery to the DC bus and it controls the charging and discharging current of the battery. It also regulates the DC bus voltage of VSC, frequency and voltage of MG. The proposed system manages the power flow of different sources like hydro and solar PV array. However, the load levelling is managed through the battery. The battery with VSC absorbs the sudden load changes, resulting in rapid regulation of DC link voltage, frequency and voltage of MG. Therefore, the system voltage and frequency regulation allows the active power balance along with the auxiliary services such as reactive power support, source current harmonics mitigation and voltage harmonics reduction at the point of common interconnection. The experimental results under various steady state and dynamic conditions, exhibit the excellent performance of the proposed system and validate the design and control of proposed MG.
Modelling and voltage control of the solar wind hybrid micro-grid with optimi...Asoka Technologies
Electricity generation from the wind and solar photovoltaic (PV) systems are highly dependent upon weather conditions. Their intermittent nature leads to fluctuations in their output. Therefore, the need for rapid compensation for energy transmission and distribution systems is increasingly important. Static Synchronous Compensator (STATCOM) can be adopted for reactive power compensation and for decreasing the voltage fluctuation caused by the system and renewable energy sources. This study presents modelling of a Solar PV-Wind Hybrid Micro-grid and the increase of the stable operating limit of the system in case of the incorporation of STATCOM is examined. The major contribution of this paper is the optimization of gain parameters of four PI controllers in STATCOM control circuit based on genetic algorithms (GA) and Bacteria Foraging Algorithm (BFA) and therefore obtaining better responses and voltage stability in terms of nonlinear nature of solar-wind hybrid micro-grid. The Simulink models of the system architecture include a wind turbine model, a solar PV power system model and a STATCOM. It is certified that the voltage fluctuation at the end of the bus bar is reduced by 8% using conventional PI controller, by 10% for GA-based PI controller, and by 15% for BFA based PI controller under variable load. The results obtained by GA and BFA-based optimization of PI controllers are compared with that of the conventional controller and better results attained.
Solar pv array fed brushless dc motor driven water pumpAsoka Technologies
This work deals with the utilization of solar photovoltaic (SPV) energy in the brushless DC (BLDC) motor driven water pump. A DC-DC boost converter, used as an intermediate power conditioning unit plays a vital role in efficiency enhancement of SPV array and soft starting of the BLDC motor with proper control. The speed control of BLDC motor is performed by PWM (Pulse Width Modulation) control of the voltage source inverter (VSI) using DC link voltage regulator. No additional control or current sensing element is required for speed control. The behavior of proposed pumping system is demonstrated by evaluating its various performances through MATLAB/simulink based simulation study.
A Novel Technique for Enhancing Active and Reactive Power Quality for Renewab...IJMER
Renewable energy resources (RES) are being increasingly connected in distribution systems utilizing power electronic converters. This paper presents a novel control strategy for achieving maximum benefits from these grid-interfacing inverters when installed in 3-phase 4-wire distribution systems. The inverter is controlled to perform as a multi-function device by incorporating active power filter functionality. The inverter can thus be utilized as: 1) power converter to inject power generated from RES to the grid, and 2) shunt APF to compensate current unbalance, load current harmonics, load reactive power demand and load neutral current. All of these functions may be accomplished either individually or simultaneously. With such a control, the combination of grid-interfacing inverter and the 3-phase 4-wire linear/non-linear unbalanced load at point of common coupling appears as balanced linear load to the grid. This new control concept is demonstrated with extensive MATLAB/Simulink simulation studies and results.
Novel High Performance Stand Alone Solar PV System with High Gain, High Effic...Asoka Technologies
This paper proposes a novel 3- stand-alone solar PV system configuration that uses high gain, high efficiency (96%) dc-dc converters both in the forward power stage as well as the bidirectional battery interface. The high voltage gain converters enable the use of low voltage PV and battery sources. This results in minimization of partial shading and parasitic capacitance effects on the PV source. Series connection of a large number of battery modules is obviated, preventing the overcharging and deep discharging issues that reduce the battery life. Also, the proposed configuration facilitates "required power tracking (RPT)" of the PV source as per the load requirements eliminating the use of expensive and 'difficult to manage' dump loads. High performance inverter operation is achieved through abc to dq reference frame transformation, which helps in generating precise information about the load's active power component for RPT, regulation of ac output voltage and minimization of control complexity. Inverter output voltage is regulated by controlling the modulation index of sinusoidal pulse width modulation, resulting in a stable and reliable system operation. The active power demand is controlled by regulating the dc link voltage. All the analytical, simulation and experimental results of this work are presented.
Standalone Photovoltaic Water Pumping System Using Induction Motor Drive with...Asoka Technologies
A simple and efficient solar photovoltaic (PV) water pumping system utilizing an induction motor drive (IMD) is presented in this paper. This solar PV water pumping system comprises of two stages of power conversion. The first stage extracts the maximum power from a solar PV array by controlling the duty ratio of a DC-DC boost converter. The DC bus voltage is maintained by the controlling the motor speed. This regulation helps in reduction of motor losses because of reduction in motor currents at higher voltage for same power injection. To control the duty ratio, an incremental conductance (INC) based maximum power point tracking (MPPT) control technique is utilized. A scalar controlled voltage source inverter (VSI) serves the purpose of operating an IMD. The stator frequency reference of IMD is generated by the proposed control scheme. The proposed system is modeled and its performance is simulated in detail. The scalar control eliminates the requirement of speed sensor/encoder. Precisely, the need of motor current sensor is also eliminated. Moreover, the dynamics are improved by an additional speed feedforward term in the control scheme. The proposed control scheme makes the system inherently immune to the pump’s constant variation. The prototype of PV powered IMD emulating the pump characteristics, is developed in the laboratory to examine the performance under different operating conditions.
SALIENT FEATURES OF GRID-CONNECTED PHOTOVOLTAIC SYSTEM AND ITS IMPACT ON POWE...Editor IJMTER
Solar energy is available to the world for free of cost from millions of years and it is a
basic energy source to the mankind. It is also one of largest energy source to the mankind. PV
systems are a relative new technology. The operational experience with PV systems itself is at an
acceptable high level and today’s installed PV systems are of a good quality and are able to operate
without any problems for many years. The price level of the PV modules and the Balance of System
costs (inverter included) have decreased significantly. This energy is available all around the world
in large quantity. When this energy is collected by the solar PV cells it is in the small power with the
D.C. supply, which is not compatible with the existing grid in the world. There is an inverter and the
converter stage comes before this energy can used. Grid interactive PV systems can vary
substantially in size.
Daymark Energy Advisors Principal Consultant Stan Faryniarz spoke on energy storage technologies as part of the session "Storage Project & Policy Successes: Enhancing Renewables Integration & Resilience" at The 2016 Renewable Energy Vermont (REV 2016) Conference.
Stand-alone Hybrid systems become appreciating issues that ensure the required electricity to consumers. The development of a stand-alone Hybrid system becomes a necessity for multiple applications The enhance energy security. To achieve this objective, we have proposed an accurate dynamic model using Multi-Agent System (MAS) in which a solar energy System (SES) serves as the main load supply, an energy Backup System (ERS) is based on a fuel cell and Electrolyzer for long-term energy storage and an Ultra Capacitor (UCap) storage system deployed as a short-time storage. To cooperate with all systems, an Intelligent Power Management (IPM) based on a specific MAS is included. Thus, to prove the performance of the system, we tested and simulated it using the Matlab/Simulink environment.
Integration of Supercapacitor in Photovoltaic Energy Storage: Modelling and C...Asoka Technologies
Due to the variable characteristics of photovoltaic energy production or the variation of the load, batteries used in storage systems renewable power can undergo many irregular cycles of charge 1 discharge. In turn, this can also have a detrimental effect on the life of the battery and can increase project costs. This paper presents an embedded energy share method between the energy storage system (battery) and the auxiliary energy storage system such as supercapacitors (SC). Supercapacitors are used to improve batteries life and reduce their stresses by providing or absorbing peaks currents as demanded by the load. The photovoltaic cells are connected to DC bus with boost converter and controlled with MPPT algorithm, Supercapacitors and batteries are linked to the DC bus through the buck-boost converter. The inductive load is connected to the DC bus by a DC-AC converter. The static converters associated with batteries and supercapacitors are controlled by current. The components of the systems are supervised through a block of energy management. The complete model of the system is implemented in MATLAB/Simulink environment. Simulation results are given to show the performance of the proposed control strategy, for the overall system.
Power flow control of hybrid micro grids using modified uipcAsoka Technologies
Neuro Fuzzy Inference System (ANFIS) controlled modified Unified Inter-Phase Power Controller (UIPC). For study, a classic hybrid micro-grid connected to grid comprising of a AC micro-grid and a DC micro-grid is taken into account. These micro-grids are interconnected employing a modified UIPC, rather than using the power converters connected in parallel. As the first input of this paper is the standard structure of UIPC, which used three power converters in every phase. It was then modified such as number of power converters is used less and implemented for the control of the exchange of power between AC-DC microgrids. In every phase there is one power electronic converter in the improved structure. It is called as Line Power Converter (LPC). Also there is Bus Power Converter (BPC) to regulate the voltage of the DC bus. The Line Power Converters links the AC micro-grid to the main grid. The DC buses are also linked with them. It can be operated in Inductance Mode (IM) as well as Capacitance Mode (CM). The control structure of LPCs has an Adaptive Fuzzy Logic Controller in it. For hybrid micro-grids, the capability of the suggested power flow control strategy is confirmed by the MATLAB simulation results.
Autonomous Power Management for Interlinked AC-DC MicrogridsAsoka Technologies
The existing power management schemes for interlinked AC-DC microgrids have several operational drawbacks. Some of the existing control schemes are designed with the main objective of sharing power among the interlinked microgrids based on their loading conditions, while other schemes regulate the voltage of the interlinked microgrids without considering the specific loading conditions. However, the existing schemes cannot achieve both objectives efficiently. To address these issues, an autonomous power management scheme is proposed, which explicitly considers the specific loading condition of the DC microgrid before importing power from the interlinked AC microgrid. This strategy enables voltage regulation in the DC microgrid, and also reduces the number of converters in operation. The proposed scheme is fully autonomous while it retains the plug-nplay features for generators and tie-converters. The performance of the proposed control scheme has been validated under different operating scenarios. The results demonstrate the effectiveness of the proposed scheme in managing the power deficit in the DC microgrid efficiently and autonomously while maintaining the better voltage regulation in the DC microgrid.
A Unified Control and Power Management Scheme for PV-Battery-Based Hybrid Mic...Asoka Technologies
Battery storage is usually employed in Photovoltaic (PV) system to mitigate the power fluctuations due to the characteristics of PV panels and solar irradiance. Control schemes for PV-battery systems must be able to stabilize the bus voltages as well as to control the power flows flexibly. This paper proposes a comprehensive control and power management system (CAPMS) for PV-battery-based hybrid microgrids with both AC and DC buses, for both grid-connected and islanded modes. The proposed CAPMS is successful in regulating the DC and AC bus voltages and frequency stably, controlling the voltage and power of each unit flexibly, and balancing the power flows in the systems automatically under different operating circumstances, regardless of disturbances from switching operating modes, fluctuations of irradiance and temperature, and change of loads. Both simulation and experimental case studies are carried out to verify the performance of the proposed method.
Modelling and voltage control of the solar wind hybrid micro-grid with optimi...Asoka Technologies
Electricity generation from the wind and solar photovoltaic (PV) systems are highly dependent upon weather conditions. Their intermittent nature leads to fluctuations in their output. Therefore, the need for rapid compensation for energy transmission and distribution systems is increasingly important. Static Synchronous Compensator (STATCOM) can be adopted for reactive power compensation and for decreasing the voltage fluctuation caused by the system and renewable energy sources. This study presents modelling of a Solar PV-Wind Hybrid Micro-grid and the increase of the stable operating limit of the system in case of the incorporation of STATCOM is examined. The major contribution of this paper is the optimization of gain parameters of four PI controllers in STATCOM control circuit based on genetic algorithms (GA) and Bacteria Foraging Algorithm (BFA) and therefore obtaining better responses and voltage stability in terms of nonlinear nature of solar-wind hybrid micro-grid. The Simulink models of the system architecture include a wind turbine model, a solar PV power system model and a STATCOM. It is certified that the voltage fluctuation at the end of the bus bar is reduced by 8% using conventional PI controller, by 10% for GA-based PI controller, and by 15% for BFA based PI controller under variable load. The results obtained by GA and BFA-based optimization of PI controllers are compared with that of the conventional controller and better results attained.
Solar pv array fed brushless dc motor driven water pumpAsoka Technologies
This work deals with the utilization of solar photovoltaic (SPV) energy in the brushless DC (BLDC) motor driven water pump. A DC-DC boost converter, used as an intermediate power conditioning unit plays a vital role in efficiency enhancement of SPV array and soft starting of the BLDC motor with proper control. The speed control of BLDC motor is performed by PWM (Pulse Width Modulation) control of the voltage source inverter (VSI) using DC link voltage regulator. No additional control or current sensing element is required for speed control. The behavior of proposed pumping system is demonstrated by evaluating its various performances through MATLAB/simulink based simulation study.
A Novel Technique for Enhancing Active and Reactive Power Quality for Renewab...IJMER
Renewable energy resources (RES) are being increasingly connected in distribution systems utilizing power electronic converters. This paper presents a novel control strategy for achieving maximum benefits from these grid-interfacing inverters when installed in 3-phase 4-wire distribution systems. The inverter is controlled to perform as a multi-function device by incorporating active power filter functionality. The inverter can thus be utilized as: 1) power converter to inject power generated from RES to the grid, and 2) shunt APF to compensate current unbalance, load current harmonics, load reactive power demand and load neutral current. All of these functions may be accomplished either individually or simultaneously. With such a control, the combination of grid-interfacing inverter and the 3-phase 4-wire linear/non-linear unbalanced load at point of common coupling appears as balanced linear load to the grid. This new control concept is demonstrated with extensive MATLAB/Simulink simulation studies and results.
Novel High Performance Stand Alone Solar PV System with High Gain, High Effic...Asoka Technologies
This paper proposes a novel 3- stand-alone solar PV system configuration that uses high gain, high efficiency (96%) dc-dc converters both in the forward power stage as well as the bidirectional battery interface. The high voltage gain converters enable the use of low voltage PV and battery sources. This results in minimization of partial shading and parasitic capacitance effects on the PV source. Series connection of a large number of battery modules is obviated, preventing the overcharging and deep discharging issues that reduce the battery life. Also, the proposed configuration facilitates "required power tracking (RPT)" of the PV source as per the load requirements eliminating the use of expensive and 'difficult to manage' dump loads. High performance inverter operation is achieved through abc to dq reference frame transformation, which helps in generating precise information about the load's active power component for RPT, regulation of ac output voltage and minimization of control complexity. Inverter output voltage is regulated by controlling the modulation index of sinusoidal pulse width modulation, resulting in a stable and reliable system operation. The active power demand is controlled by regulating the dc link voltage. All the analytical, simulation and experimental results of this work are presented.
Standalone Photovoltaic Water Pumping System Using Induction Motor Drive with...Asoka Technologies
A simple and efficient solar photovoltaic (PV) water pumping system utilizing an induction motor drive (IMD) is presented in this paper. This solar PV water pumping system comprises of two stages of power conversion. The first stage extracts the maximum power from a solar PV array by controlling the duty ratio of a DC-DC boost converter. The DC bus voltage is maintained by the controlling the motor speed. This regulation helps in reduction of motor losses because of reduction in motor currents at higher voltage for same power injection. To control the duty ratio, an incremental conductance (INC) based maximum power point tracking (MPPT) control technique is utilized. A scalar controlled voltage source inverter (VSI) serves the purpose of operating an IMD. The stator frequency reference of IMD is generated by the proposed control scheme. The proposed system is modeled and its performance is simulated in detail. The scalar control eliminates the requirement of speed sensor/encoder. Precisely, the need of motor current sensor is also eliminated. Moreover, the dynamics are improved by an additional speed feedforward term in the control scheme. The proposed control scheme makes the system inherently immune to the pump’s constant variation. The prototype of PV powered IMD emulating the pump characteristics, is developed in the laboratory to examine the performance under different operating conditions.
SALIENT FEATURES OF GRID-CONNECTED PHOTOVOLTAIC SYSTEM AND ITS IMPACT ON POWE...Editor IJMTER
Solar energy is available to the world for free of cost from millions of years and it is a
basic energy source to the mankind. It is also one of largest energy source to the mankind. PV
systems are a relative new technology. The operational experience with PV systems itself is at an
acceptable high level and today’s installed PV systems are of a good quality and are able to operate
without any problems for many years. The price level of the PV modules and the Balance of System
costs (inverter included) have decreased significantly. This energy is available all around the world
in large quantity. When this energy is collected by the solar PV cells it is in the small power with the
D.C. supply, which is not compatible with the existing grid in the world. There is an inverter and the
converter stage comes before this energy can used. Grid interactive PV systems can vary
substantially in size.
Daymark Energy Advisors Principal Consultant Stan Faryniarz spoke on energy storage technologies as part of the session "Storage Project & Policy Successes: Enhancing Renewables Integration & Resilience" at The 2016 Renewable Energy Vermont (REV 2016) Conference.
Stand-alone Hybrid systems become appreciating issues that ensure the required electricity to consumers. The development of a stand-alone Hybrid system becomes a necessity for multiple applications The enhance energy security. To achieve this objective, we have proposed an accurate dynamic model using Multi-Agent System (MAS) in which a solar energy System (SES) serves as the main load supply, an energy Backup System (ERS) is based on a fuel cell and Electrolyzer for long-term energy storage and an Ultra Capacitor (UCap) storage system deployed as a short-time storage. To cooperate with all systems, an Intelligent Power Management (IPM) based on a specific MAS is included. Thus, to prove the performance of the system, we tested and simulated it using the Matlab/Simulink environment.
Integration of Supercapacitor in Photovoltaic Energy Storage: Modelling and C...Asoka Technologies
Due to the variable characteristics of photovoltaic energy production or the variation of the load, batteries used in storage systems renewable power can undergo many irregular cycles of charge 1 discharge. In turn, this can also have a detrimental effect on the life of the battery and can increase project costs. This paper presents an embedded energy share method between the energy storage system (battery) and the auxiliary energy storage system such as supercapacitors (SC). Supercapacitors are used to improve batteries life and reduce their stresses by providing or absorbing peaks currents as demanded by the load. The photovoltaic cells are connected to DC bus with boost converter and controlled with MPPT algorithm, Supercapacitors and batteries are linked to the DC bus through the buck-boost converter. The inductive load is connected to the DC bus by a DC-AC converter. The static converters associated with batteries and supercapacitors are controlled by current. The components of the systems are supervised through a block of energy management. The complete model of the system is implemented in MATLAB/Simulink environment. Simulation results are given to show the performance of the proposed control strategy, for the overall system.
Power flow control of hybrid micro grids using modified uipcAsoka Technologies
Neuro Fuzzy Inference System (ANFIS) controlled modified Unified Inter-Phase Power Controller (UIPC). For study, a classic hybrid micro-grid connected to grid comprising of a AC micro-grid and a DC micro-grid is taken into account. These micro-grids are interconnected employing a modified UIPC, rather than using the power converters connected in parallel. As the first input of this paper is the standard structure of UIPC, which used three power converters in every phase. It was then modified such as number of power converters is used less and implemented for the control of the exchange of power between AC-DC microgrids. In every phase there is one power electronic converter in the improved structure. It is called as Line Power Converter (LPC). Also there is Bus Power Converter (BPC) to regulate the voltage of the DC bus. The Line Power Converters links the AC micro-grid to the main grid. The DC buses are also linked with them. It can be operated in Inductance Mode (IM) as well as Capacitance Mode (CM). The control structure of LPCs has an Adaptive Fuzzy Logic Controller in it. For hybrid micro-grids, the capability of the suggested power flow control strategy is confirmed by the MATLAB simulation results.
Autonomous Power Management for Interlinked AC-DC MicrogridsAsoka Technologies
The existing power management schemes for interlinked AC-DC microgrids have several operational drawbacks. Some of the existing control schemes are designed with the main objective of sharing power among the interlinked microgrids based on their loading conditions, while other schemes regulate the voltage of the interlinked microgrids without considering the specific loading conditions. However, the existing schemes cannot achieve both objectives efficiently. To address these issues, an autonomous power management scheme is proposed, which explicitly considers the specific loading condition of the DC microgrid before importing power from the interlinked AC microgrid. This strategy enables voltage regulation in the DC microgrid, and also reduces the number of converters in operation. The proposed scheme is fully autonomous while it retains the plug-nplay features for generators and tie-converters. The performance of the proposed control scheme has been validated under different operating scenarios. The results demonstrate the effectiveness of the proposed scheme in managing the power deficit in the DC microgrid efficiently and autonomously while maintaining the better voltage regulation in the DC microgrid.
A Unified Control and Power Management Scheme for PV-Battery-Based Hybrid Mic...Asoka Technologies
Battery storage is usually employed in Photovoltaic (PV) system to mitigate the power fluctuations due to the characteristics of PV panels and solar irradiance. Control schemes for PV-battery systems must be able to stabilize the bus voltages as well as to control the power flows flexibly. This paper proposes a comprehensive control and power management system (CAPMS) for PV-battery-based hybrid microgrids with both AC and DC buses, for both grid-connected and islanded modes. The proposed CAPMS is successful in regulating the DC and AC bus voltages and frequency stably, controlling the voltage and power of each unit flexibly, and balancing the power flows in the systems automatically under different operating circumstances, regardless of disturbances from switching operating modes, fluctuations of irradiance and temperature, and change of loads. Both simulation and experimental case studies are carried out to verify the performance of the proposed method.
Implementation Of A High-Efficiency, High-Lifetime, And Low-Cost Converter Us...irjes
This paper proposes a new converter for photovoltaic water pumping and treatment systems without
the use of storage elements. The converter is designed to drive a three-phase induction motor directly from PV
solar energy. The use of this motor has the objective of presenting a better solution to the standard DC motor
water pumping system. The development is oriented to achieve a commercially viable solution and a market
friendly product. The converter topology is based on a Resonant Two Inductor Boost converter and a Threephase
Voltage Source inverter achieving 90% efficiency at a rated power of 210W.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Energy Management of Distributed Generation Inverters using MPC Controller i...IJMER
This paper presents a microgrid consisting of different distributed generation (DG) units
that are connected to the distribution grid. An energy-management algorithm is implemented to
coordinate the operations of the different DG units in the microgrid for grid-connected and islanded
operations. The proposed microgrid consists of a photovoltaic (PV) array which functions as the
primary generation unit of the microgrid and a proton-exchange membrane fuel cell to supplement the
variability in the power generated by the PV array. A lithium-ion storage battery is incorporated into
the microgrid to mitigate peak demands during grid-connected operation and to compensate for any
shortage in the generated power during islanded operation. The control design for the DG inverters
employs a new model predictive control algorithm which enables faster computational time for large
power systems by optimizing the steady-state and the transient control problems separately. The design
concept is verified through various test scenarios to demonstrate the operational capability of the
proposed microgrid, and the obtained results are discussed.
Performance Analysis of DC Micro Grid with PV-Fuel Cell Hybrid GenerationIJMREMJournal
Conventional energy resources are being replaced by Renewable energy sources mainly due to increasing
environmental concerns. Photovoltaic (PV) and Fuel cell (FC) are suitable to be used in modern DC microgrids
due to their DC output. In this research work, a DC microgrid structure is proposed for small residential areas
using hybrid PV and FC generation. Power Electronic converters are used to regulate generated voltage of the
two sources for integration to a common DC bus. Proposed system is simulated using MATLAB SIMULINK to
observe its performance. Simulation results show that output voltage is properly maintained at different DC
Reactive Power Sharing Droop Control Strategy for DG Units in an Islanded Mic...IJMTST Journal
The proposed method mainly includes two important operations: error reduction operation and voltage
recovery operation. The sharing accuracy is improved by the sharing error reduction operation, which is
activated by the low-bandwidth synchronization signals. However, the error reduction operation will result in
a decrease in output voltage amplitude. Therefore, the voltage recovery operation is proposed to compensate
the decrease., due to increasing the demand of electricity as well as rapid depletion of fossil fuels, and the
government policies on reduction of greenhouse gas emissions , renewable energy technologies are more
attractive and various types of distributed generation sources, such as wind turbine generators and solar
photo voltaic panels are being connected to low-voltage distribution networks. Micro grid is an integrated
system that contain in s distributed generation sources, control systems, load management, energy storage
and communication infrastructure capability to work in both grid connected and island mode to optimize
energy usage. The paper presents a advanced control technique for a micro grid system which works
efficiently under a decentralized control system.
Simulink Model for Cost-effective Analysis of Hybrid SystemIJMER
Utilization of non conventional sources of energy to meet the present day energy requirement has become very much essential in the era of fossil fuel crises. The present paper discusses the importance of PV-Diesel hybrid system to meet electrical requirement in remote areas. A model of a photovoltaic array with diesel battery was designed by MATLAB simulink. In this paper, the cost-effective analysis which includes the fuel consumed, the energy obtained per gallon of fuel supplied, and the total cost of fuel. Simulations done for Diesel generator system, diesel-battery system and solar PV with diesel-battery system using a one-year time period. Based on simulation results energy payback period for PV array, the simple payback time for the PV module calculated. Simulation analysis includes the comparison of system cost, efficiency, and kWh per gallon with those predicted by Hybrid Optimization Model for Electric Renewables (HOMER).
Similar to IRJET- Simulation of Solar PV and DG based Hybrid Micro Grid (20)
Vaccine management system project report documentation..pdfKamal Acharya
The Division of Vaccine and Immunization is facing increasing difficulty monitoring vaccines and other commodities distribution once they have been distributed from the national stores. With the introduction of new vaccines, more challenges have been anticipated with this additions posing serious threat to the already over strained vaccine supply chain system in Kenya.
COLLEGE BUS MANAGEMENT SYSTEM PROJECT REPORT.pdfKamal Acharya
The College Bus Management system is completely developed by Visual Basic .NET Version. The application is connect with most secured database language MS SQL Server. The application is develop by using best combination of front-end and back-end languages. The application is totally design like flat user interface. This flat user interface is more attractive user interface in 2017. The application is gives more important to the system functionality. The application is to manage the student’s details, driver’s details, bus details, bus route details, bus fees details and more. The application has only one unit for admin. The admin can manage the entire application. The admin can login into the application by using username and password of the admin. The application is develop for big and small colleges. It is more user friendly for non-computer person. Even they can easily learn how to manage the application within hours. The application is more secure by the admin. The system will give an effective output for the VB.Net and SQL Server given as input to the system. The compiled java program given as input to the system, after scanning the program will generate different reports. The application generates the report for users. The admin can view and download the report of the data. The application deliver the excel format reports. Because, excel formatted reports is very easy to understand the income and expense of the college bus. This application is mainly develop for windows operating system users. In 2017, 73% of people enterprises are using windows operating system. So the application will easily install for all the windows operating system users. The application-developed size is very low. The application consumes very low space in disk. Therefore, the user can allocate very minimum local disk space for this application.
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
Event Management System Vb Net Project Report.pdfKamal Acharya
In present era, the scopes of information technology growing with a very fast .We do not see any are untouched from this industry. The scope of information technology has become wider includes: Business and industry. Household Business, Communication, Education, Entertainment, Science, Medicine, Engineering, Distance Learning, Weather Forecasting. Carrier Searching and so on.
My project named “Event Management System” is software that store and maintained all events coordinated in college. It also helpful to print related reports. My project will help to record the events coordinated by faculties with their Name, Event subject, date & details in an efficient & effective ways.
In my system we have to make a system by which a user can record all events coordinated by a particular faculty. In our proposed system some more featured are added which differs it from the existing system such as security.
Courier management system project report.pdfKamal Acharya
It is now-a-days very important for the people to send or receive articles like imported furniture, electronic items, gifts, business goods and the like. People depend vastly on different transport systems which mostly use the manual way of receiving and delivering the articles. There is no way to track the articles till they are received and there is no way to let the customer know what happened in transit, once he booked some articles. In such a situation, we need a system which completely computerizes the cargo activities including time to time tracking of the articles sent. This need is fulfilled by Courier Management System software which is online software for the cargo management people that enables them to receive the goods from a source and send them to a required destination and track their status from time to time.
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
Quality defects in TMT Bars, Possible causes and Potential Solutions.PrashantGoswami42
Maintaining high-quality standards in the production of TMT bars is crucial for ensuring structural integrity in construction. Addressing common defects through careful monitoring, standardized processes, and advanced technology can significantly improve the quality of TMT bars. Continuous training and adherence to quality control measures will also play a pivotal role in minimizing these defects.
Democratizing Fuzzing at Scale by Abhishek Aryaabh.arya
Presented at NUS: Fuzzing and Software Security Summer School 2024
This keynote talks about the democratization of fuzzing at scale, highlighting the collaboration between open source communities, academia, and industry to advance the field of fuzzing. It delves into the history of fuzzing, the development of scalable fuzzing platforms, and the empowerment of community-driven research. The talk will further discuss recent advancements leveraging AI/ML and offer insights into the future evolution of the fuzzing landscape.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Forklift Classes Overview by Intella PartsIntella Parts
Discover the different forklift classes and their specific applications. Learn how to choose the right forklift for your needs to ensure safety, efficiency, and compliance in your operations.
For more technical information, visit our website https://intellaparts.com
Automobile Management System Project Report.pdfKamal Acharya
The proposed project is developed to manage the automobile in the automobile dealer company. The main module in this project is login, automobile management, customer management, sales, complaints and reports. The first module is the login. The automobile showroom owner should login to the project for usage. The username and password are verified and if it is correct, next form opens. If the username and password are not correct, it shows the error message.
When a customer search for a automobile, if the automobile is available, they will be taken to a page that shows the details of the automobile including automobile name, automobile ID, quantity, price etc. “Automobile Management System” is useful for maintaining automobiles, customers effectively and hence helps for establishing good relation between customer and automobile organization. It contains various customized modules for effectively maintaining automobiles and stock information accurately and safely.
When the automobile is sold to the customer, stock will be reduced automatically. When a new purchase is made, stock will be increased automatically. While selecting automobiles for sale, the proposed software will automatically check for total number of available stock of that particular item, if the total stock of that particular item is less than 5, software will notify the user to purchase the particular item.
Also when the user tries to sale items which are not in stock, the system will prompt the user that the stock is not enough. Customers of this system can search for a automobile; can purchase a automobile easily by selecting fast. On the other hand the stock of automobiles can be maintained perfectly by the automobile shop manager overcoming the drawbacks of existing system.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers