Minmax
•Download as PPTX, PDF•
0 likes•28 views
The document describes an IC245 bidirectional buffer and IC373 octal latch. The IC245 can drive data in both directions on a bus, sourcing 15mA and sinking 24mA. It contains 16 non-inverting buffers that are controlled by a DIR pin to determine the direction of data flow. The IC373 octal latch is used to separate address and data on a bus and is controlled by an ALE signal. It also describes the minimum and maximum mode read and write bus cycles for an 8086-based system using these chips.
Report
Share
Report
Share
Recommended
19. io interfacing i
This document discusses two schemes for interfacing I/O devices with a microprocessor: memory mapped I/O and I/O mapped I/O. Memory mapped I/O treats I/O devices like memory locations, using memory instructions and addresses to transfer data. I/O mapped I/O uses special IN and OUT instructions to specify an 8-bit port address for input or output. Examples are given of transferring data between an accumulator and memory/I/O locations using LDA, STA, IN, and OUT instructions.
Microprocessor-Architecture [8085]
Generates control signals and status signals to
control data flow and operation of different units.
Microprocessor-Architecture [8085]
The document discusses the architecture of the 8085 microprocessor. It was designed by Intel in 1977 using NMOS technology. It has an 8-bit data bus and 16-bit address bus. The main components are an 8-bit accumulator, arithmetic logic unit, six 8-bit general purpose registers arranged in pairs, 16-bit program counter, 16-bit stack pointer, and 8-bit flag register. It also has an instruction register and decoder to fetch and decode instructions from memory. Interrupt handling is supported through five interrupt signals.
Microprocessors 8085 architecture
The microprocessor is the central processing unit of a computer. It is the heart of the computer. 8085 is one of the most popular 8-Bit microprocessors in India. Because of its unique characteristics of both industry and academics still regarded as standard this microprocessor.
20. io interfacing ii
The document discusses I/O interfacing and provides an example of using an OUT instruction to display data from the accumulator on LEDs connected to an output port. It explains that during the M3 cycle of the OUT instruction, the processor places the accumulator data on the data bus. This bus is connected to a latch that is enabled by the IO/M and WR signals to catch the data and display it on the LEDs. It describes how the address of the latch is determined by decoding the address bus lines to generate a device select pulse only when a specific port address is present.
Microprocessors 8085 pin diagram
The document summarizes the pin diagram of the 8085 microprocessor. It describes the various pins including the address bus pins A15-A8 that carry the most significant 8 bits of the memory/IO address and pins AD7-AD0 that carry the least significant 8 bits of the address and data bus. It also describes the control signals like RD, WR, and ALE, the status signals IO/M, S1 and S0, the power supply pins VCC and VSS, the clock signals X1, X2 and CLK OUT, the interrupt pins like TRAP, RST 7.5, RST 6.5, RST 5.5, and INTR, and the serial I
8255_utkarsh_kulshrestha
Presentation on IC 8255 programmable peripheral interface with complete description of modes and its examples.
Microprocessor-Compatible Quadrature Decoder/Counter Design
A microprocessor-compatible quadrature decoder/counter is used to interface an optical shaft encoder (OSE) to a microprocessor's system bus. Quadrature decoder/counter find application in digital data input subsystems and digital closed loop motion control systems.
Recommended
19. io interfacing i
This document discusses two schemes for interfacing I/O devices with a microprocessor: memory mapped I/O and I/O mapped I/O. Memory mapped I/O treats I/O devices like memory locations, using memory instructions and addresses to transfer data. I/O mapped I/O uses special IN and OUT instructions to specify an 8-bit port address for input or output. Examples are given of transferring data between an accumulator and memory/I/O locations using LDA, STA, IN, and OUT instructions.
Microprocessor-Architecture [8085]
Generates control signals and status signals to
control data flow and operation of different units.
Microprocessor-Architecture [8085]
The document discusses the architecture of the 8085 microprocessor. It was designed by Intel in 1977 using NMOS technology. It has an 8-bit data bus and 16-bit address bus. The main components are an 8-bit accumulator, arithmetic logic unit, six 8-bit general purpose registers arranged in pairs, 16-bit program counter, 16-bit stack pointer, and 8-bit flag register. It also has an instruction register and decoder to fetch and decode instructions from memory. Interrupt handling is supported through five interrupt signals.
Microprocessors 8085 architecture
The microprocessor is the central processing unit of a computer. It is the heart of the computer. 8085 is one of the most popular 8-Bit microprocessors in India. Because of its unique characteristics of both industry and academics still regarded as standard this microprocessor.
20. io interfacing ii
The document discusses I/O interfacing and provides an example of using an OUT instruction to display data from the accumulator on LEDs connected to an output port. It explains that during the M3 cycle of the OUT instruction, the processor places the accumulator data on the data bus. This bus is connected to a latch that is enabled by the IO/M and WR signals to catch the data and display it on the LEDs. It describes how the address of the latch is determined by decoding the address bus lines to generate a device select pulse only when a specific port address is present.
Microprocessors 8085 pin diagram
The document summarizes the pin diagram of the 8085 microprocessor. It describes the various pins including the address bus pins A15-A8 that carry the most significant 8 bits of the memory/IO address and pins AD7-AD0 that carry the least significant 8 bits of the address and data bus. It also describes the control signals like RD, WR, and ALE, the status signals IO/M, S1 and S0, the power supply pins VCC and VSS, the clock signals X1, X2 and CLK OUT, the interrupt pins like TRAP, RST 7.5, RST 6.5, RST 5.5, and INTR, and the serial I
8255_utkarsh_kulshrestha
Presentation on IC 8255 programmable peripheral interface with complete description of modes and its examples.
Microprocessor-Compatible Quadrature Decoder/Counter Design
A microprocessor-compatible quadrature decoder/counter is used to interface an optical shaft encoder (OSE) to a microprocessor's system bus. Quadrature decoder/counter find application in digital data input subsystems and digital closed loop motion control systems.
Microprocessors
The microprocessor contains an ALU, registers, and a control unit connected by an internal data bus. The ALU performs arithmetic and logical operations on data from the registers. The registers include general purpose registers, accumulators, flags, and pointers to hold data and addresses. The control unit provides timing and control signals to synchronize data transfers between components.
An Overview Study on I/O Expander with I2C and SMBus Interface
This document provides an overview of an I/O expander chip that uses the I2C and SMBus interfaces. It has 8 or 16 programmable GPIO pins that are configurable as inputs or outputs. The chip includes input and output registers, configuration registers to set pin directions, and polarity inversion registers. It is commonly used for applications like keypad control, LED control, sensor monitoring, and fan control. Block diagrams and typical application circuits are shown to illustrate its features and interface.
8155 Basic Concepts
The document discusses the 8155 programmable interface device. The 8155 can be used to interface I/O devices to a microprocessor like the 8085. It contains 256 bytes of RAM, three I/O ports (Ports A, B, and C), and a 14-bit timer. The 8155 is programmed by the 8085 which sends data and instruction words to configure the I/O ports and timer registers. The timer on the 8155 has two registers and can operate in four modes to generate different output waveforms.
8085 Microprocessor
This document discusses the 8085 microprocessor, including its history, features, and architecture. The 8085 is an 8-bit microprocessor introduced in 1976 that has an 8-bit data bus, 16-bit address bus, and can address up to 64KB of memory. It operates at a clock speed of up to 3.2MHz. The document describes the various components of the 8085, including its buses, instruction register, timing and control circuit, accumulator and ALU, interrupt and serial I/O, and registers.
An application of 8085 register interfacing with LED
This ppt will guide you through the steps to interface a seven segment led with a 8085 microprocessor.
Comparative Analysis of Different Types of Full Adder Circuits
This document compares different types of full adder circuits, including conventional 28 transistor, 14 transistor, 8 transistor, and dynamic logic circuits. It provides truth tables and equations for full adders and describes various circuit designs like transmission gate, static energy recovery, Gate Diffusion Input (GDI), and dual rail domino logic. Simulation results comparing power, delay, and power-delay product for each circuit are presented, showing that dual rail domino logic has the lowest power and power-delay product, while also having one of the lowest delays. In conclusion, dual rail domino logic is identified as an efficient full adder design.
An application of 8085 register interfacing with LCD
This ppt will guide you through the steps to interface a seven segment lcd with a 8085 microprocessor.
Avionics buses
The document discusses several avionics data buses used for digital communication within aircraft systems. It describes the evolution from early single-source single-sink configurations to modern multi-source multi-sink buses. Key buses covered include ARINC 429, ARINC 629, MIL-STD 1553, and MIL-STD 1773. ARINC 429 uses a single-source multi-sink topology with transmission rates from 12-100kbps. MIL-STD 1553 is a half-duplex multi-source multi-sink bus that operates at 1Mbps and coordinates data transfer through a central Bus Controller. MIL-STD 1773 is similar to 1553 but uses optical cabling instead of voltage-based
Lecture 06 pic programming in c
PIC programming in C has been introduced here. Basic knowledge about PIC programming using C language can be found here.
Lecture 05 pic io port programming
This slide set is organized to introduce port programming of PIC micro-controller. Input-output programming of PIC is covered here.
SC28C94: Quad Universal Asynchronous Receiver/Transmitter (QUART)
This training module introduces 28C94 quad universal asynchronous receiver/transmitter, its internal operation, and applications.
8085 architecture
The 8085 microprocessor is an 8-bit processor with 6,200 transistors. It has 74 instructions and can address 64KB of memory. The 8085 has an arithmetic logic unit (ALU) that performs arithmetic and logic operations on data from the accumulator and registers. It also has a control unit, registers, and interfaces to external memory and I/O devices. The 8085's architecture includes components like the accumulator, flags register, and general purpose registers that help it process instructions.
Gigamon Systems Hardware Tour
Data Access Network (DAN) is a newly emerging "best practice" for passive monitoring of mission critical networks that solves real access problems, improves network performance and uptime, and saves capital, operation and maintenance costs. A DAN is a combination of out-of-band data access switching plus passive monitoring instrumentation to enable required security, compliance, forensics review, application performance, VoIP QoS, uptime and other network management tasks. Data is acquired from multiple SPAN ports or taps and multicast to multiple tools, aggregated to a few consolidated tools, and filtered or divided across many instances of the same tools. This Podcast recommends the DAN as a solution to those who suffer real problems like too many tools and not enough span ports, too many links to monitor and not enough money to deploy distributed tools, or too much traffic that threatens to overflow even the highest capacity tool.
EE2356 Microprocessor and Microcontroller Lab Manuel
The document discusses assembly language programs for arithmetic operations and data conversions using an 8085 microprocessor. It includes algorithms and programs for 8-bit addition, subtraction, multiplication, and division. It also covers sorting data in ascending and descending order, finding minimum and maximum values, and performing rotate instructions. Additional programs are provided for converting between ASCII, hexadecimal, and BCD codes.
An Overview Study on MEMS digital output motion sensor: LIS331DLH
The document provides an overview of the LIS331DLH MEMS digital output motion sensor from STMicroelectronics. It describes the sensor's key features such as wide voltage compatibility, low power modes, and integrated self-test. Applications include motion detection, free-fall detection, display orientation, and more. Block diagrams are shown of the sensor's architecture, interrupt generation, and SPI interface. A demonstration kit is also mentioned.
8051 microcontoller.ppt
8051 microcontroller architecture and pin diagram (signal description) made easy to learn and understand with ppt for revision during exams . Most Favourable for class presentations
Register organization
The 80386 processor was Intel's third generation processor and first 32-bit version of the 8086 processors. It had three variants - the 80386DX, 80386SX, and 80386SL. The 80386DX had 32 32-bit general purpose registers that could be used as 8-bit or 16-bit registers, as well as 16-bit segment registers and an instruction pointer. Its register organization included 8 general purpose registers, segment registers, and flags register.
Arc System Overview By Cristian Randieri
The document summarizes the ARC (APV Readout Controller) system, which is used to test silicon strip tracker modules for the CMS experiment at the LHC. The ARC system allows control and readout of the frontend hybrid electronics and consists of an ARC board, interface cards, and software. It can monitor hybrid data, store calibration data, and perform automated fast tests of the hybrids and modules.
Managing register banks in the cloud with airhdl
The document discusses airhdl, a web-based tool for managing FPGA register banks. It describes how airhdl allows users to define register maps graphically in a web browser. This includes registers, fields, access modes, and other properties. Airhdl then generates RTL code, C header files, and documentation based on the defined register map. It aims to simplify the process of maintaining consistency between hardware and software register definitions. The presentation concludes with a demo of airhdl and plans for future work.
Microprocessor Interfacing and 8155 Features
The 8155 and 8156 microprocessor interface chips differ in that the 8155 has an active low Chip Enable (CE) signal, while the 8156 has an active high CE signal. The 8155 is a multifunction chip that contains RAM, I/O ports, and a timer. It has two 8-bit I/O ports, one 6-bit I/O port, a 14-bit counter/timer, 2Kb of RAM, and can be interfaced with the 8085 microprocessor. The document then provides details on the pinout, memory mapping, control register, port configurations, timer operation modes, and status register of the 8155 chip.
Avr report
The document provides information about training performed on the AVR microcontroller. It discusses the features of the ATmega8 microcontroller including its architecture, memory, I/O ports, and peripherals. It also describes tasks performed during training such as interfacing LEDs, buttons, keypads, displays, ADC, and DC motors to learn about digital I/O, serial communication, and analog input.
UNIT- 3.pptx
This document provides information on peripheral interfacing in microprocessors. It discusses memory interfacing and I/O interfacing, and some of the peripheral devices developed by Intel like the 8255 parallel communication interface, 8251 serial communication interface, 8254 programmable timer, and 8257 DMA controller. It then describes serial and parallel communication interfaces. It provides details on the 8255 programmable peripheral interface and its operating modes. Finally, it discusses digital to analog converters, applications of the 8254 timer/counter, and analog to digital converters.
More Related Content
What's hot
Microprocessors
The microprocessor contains an ALU, registers, and a control unit connected by an internal data bus. The ALU performs arithmetic and logical operations on data from the registers. The registers include general purpose registers, accumulators, flags, and pointers to hold data and addresses. The control unit provides timing and control signals to synchronize data transfers between components.
An Overview Study on I/O Expander with I2C and SMBus Interface
This document provides an overview of an I/O expander chip that uses the I2C and SMBus interfaces. It has 8 or 16 programmable GPIO pins that are configurable as inputs or outputs. The chip includes input and output registers, configuration registers to set pin directions, and polarity inversion registers. It is commonly used for applications like keypad control, LED control, sensor monitoring, and fan control. Block diagrams and typical application circuits are shown to illustrate its features and interface.
8155 Basic Concepts
The document discusses the 8155 programmable interface device. The 8155 can be used to interface I/O devices to a microprocessor like the 8085. It contains 256 bytes of RAM, three I/O ports (Ports A, B, and C), and a 14-bit timer. The 8155 is programmed by the 8085 which sends data and instruction words to configure the I/O ports and timer registers. The timer on the 8155 has two registers and can operate in four modes to generate different output waveforms.
8085 Microprocessor
This document discusses the 8085 microprocessor, including its history, features, and architecture. The 8085 is an 8-bit microprocessor introduced in 1976 that has an 8-bit data bus, 16-bit address bus, and can address up to 64KB of memory. It operates at a clock speed of up to 3.2MHz. The document describes the various components of the 8085, including its buses, instruction register, timing and control circuit, accumulator and ALU, interrupt and serial I/O, and registers.
An application of 8085 register interfacing with LED
This ppt will guide you through the steps to interface a seven segment led with a 8085 microprocessor.
Comparative Analysis of Different Types of Full Adder Circuits
This document compares different types of full adder circuits, including conventional 28 transistor, 14 transistor, 8 transistor, and dynamic logic circuits. It provides truth tables and equations for full adders and describes various circuit designs like transmission gate, static energy recovery, Gate Diffusion Input (GDI), and dual rail domino logic. Simulation results comparing power, delay, and power-delay product for each circuit are presented, showing that dual rail domino logic has the lowest power and power-delay product, while also having one of the lowest delays. In conclusion, dual rail domino logic is identified as an efficient full adder design.
An application of 8085 register interfacing with LCD
This ppt will guide you through the steps to interface a seven segment lcd with a 8085 microprocessor.
Avionics buses
The document discusses several avionics data buses used for digital communication within aircraft systems. It describes the evolution from early single-source single-sink configurations to modern multi-source multi-sink buses. Key buses covered include ARINC 429, ARINC 629, MIL-STD 1553, and MIL-STD 1773. ARINC 429 uses a single-source multi-sink topology with transmission rates from 12-100kbps. MIL-STD 1553 is a half-duplex multi-source multi-sink bus that operates at 1Mbps and coordinates data transfer through a central Bus Controller. MIL-STD 1773 is similar to 1553 but uses optical cabling instead of voltage-based
Lecture 06 pic programming in c
PIC programming in C has been introduced here. Basic knowledge about PIC programming using C language can be found here.
Lecture 05 pic io port programming
This slide set is organized to introduce port programming of PIC micro-controller. Input-output programming of PIC is covered here.
SC28C94: Quad Universal Asynchronous Receiver/Transmitter (QUART)
This training module introduces 28C94 quad universal asynchronous receiver/transmitter, its internal operation, and applications.
8085 architecture
The 8085 microprocessor is an 8-bit processor with 6,200 transistors. It has 74 instructions and can address 64KB of memory. The 8085 has an arithmetic logic unit (ALU) that performs arithmetic and logic operations on data from the accumulator and registers. It also has a control unit, registers, and interfaces to external memory and I/O devices. The 8085's architecture includes components like the accumulator, flags register, and general purpose registers that help it process instructions.
Gigamon Systems Hardware Tour
Data Access Network (DAN) is a newly emerging "best practice" for passive monitoring of mission critical networks that solves real access problems, improves network performance and uptime, and saves capital, operation and maintenance costs. A DAN is a combination of out-of-band data access switching plus passive monitoring instrumentation to enable required security, compliance, forensics review, application performance, VoIP QoS, uptime and other network management tasks. Data is acquired from multiple SPAN ports or taps and multicast to multiple tools, aggregated to a few consolidated tools, and filtered or divided across many instances of the same tools. This Podcast recommends the DAN as a solution to those who suffer real problems like too many tools and not enough span ports, too many links to monitor and not enough money to deploy distributed tools, or too much traffic that threatens to overflow even the highest capacity tool.
EE2356 Microprocessor and Microcontroller Lab Manuel
The document discusses assembly language programs for arithmetic operations and data conversions using an 8085 microprocessor. It includes algorithms and programs for 8-bit addition, subtraction, multiplication, and division. It also covers sorting data in ascending and descending order, finding minimum and maximum values, and performing rotate instructions. Additional programs are provided for converting between ASCII, hexadecimal, and BCD codes.
An Overview Study on MEMS digital output motion sensor: LIS331DLH
The document provides an overview of the LIS331DLH MEMS digital output motion sensor from STMicroelectronics. It describes the sensor's key features such as wide voltage compatibility, low power modes, and integrated self-test. Applications include motion detection, free-fall detection, display orientation, and more. Block diagrams are shown of the sensor's architecture, interrupt generation, and SPI interface. A demonstration kit is also mentioned.
8051 microcontoller.ppt
8051 microcontroller architecture and pin diagram (signal description) made easy to learn and understand with ppt for revision during exams . Most Favourable for class presentations
Register organization
The 80386 processor was Intel's third generation processor and first 32-bit version of the 8086 processors. It had three variants - the 80386DX, 80386SX, and 80386SL. The 80386DX had 32 32-bit general purpose registers that could be used as 8-bit or 16-bit registers, as well as 16-bit segment registers and an instruction pointer. Its register organization included 8 general purpose registers, segment registers, and flags register.
Arc System Overview By Cristian Randieri
The document summarizes the ARC (APV Readout Controller) system, which is used to test silicon strip tracker modules for the CMS experiment at the LHC. The ARC system allows control and readout of the frontend hybrid electronics and consists of an ARC board, interface cards, and software. It can monitor hybrid data, store calibration data, and perform automated fast tests of the hybrids and modules.
Managing register banks in the cloud with airhdl
The document discusses airhdl, a web-based tool for managing FPGA register banks. It describes how airhdl allows users to define register maps graphically in a web browser. This includes registers, fields, access modes, and other properties. Airhdl then generates RTL code, C header files, and documentation based on the defined register map. It aims to simplify the process of maintaining consistency between hardware and software register definitions. The presentation concludes with a demo of airhdl and plans for future work.
Microprocessor Interfacing and 8155 Features
The 8155 and 8156 microprocessor interface chips differ in that the 8155 has an active low Chip Enable (CE) signal, while the 8156 has an active high CE signal. The 8155 is a multifunction chip that contains RAM, I/O ports, and a timer. It has two 8-bit I/O ports, one 6-bit I/O port, a 14-bit counter/timer, 2Kb of RAM, and can be interfaced with the 8085 microprocessor. The document then provides details on the pinout, memory mapping, control register, port configurations, timer operation modes, and status register of the 8155 chip.
What's hot (20)
An Overview Study on I/O Expander with I2C and SMBus Interface
An Overview Study on I/O Expander with I2C and SMBus Interface
An application of 8085 register interfacing with LED
An application of 8085 register interfacing with LED
Comparative Analysis of Different Types of Full Adder Circuits
Comparative Analysis of Different Types of Full Adder Circuits
An application of 8085 register interfacing with LCD
An application of 8085 register interfacing with LCD
SC28C94: Quad Universal Asynchronous Receiver/Transmitter (QUART)
SC28C94: Quad Universal Asynchronous Receiver/Transmitter (QUART)
EE2356 Microprocessor and Microcontroller Lab Manuel
EE2356 Microprocessor and Microcontroller Lab Manuel
An Overview Study on MEMS digital output motion sensor: LIS331DLH
An Overview Study on MEMS digital output motion sensor: LIS331DLH
Similar to Minmax
Avr report
The document provides information about training performed on the AVR microcontroller. It discusses the features of the ATmega8 microcontroller including its architecture, memory, I/O ports, and peripherals. It also describes tasks performed during training such as interfacing LEDs, buttons, keypads, displays, ADC, and DC motors to learn about digital I/O, serial communication, and analog input.
UNIT- 3.pptx
This document provides information on peripheral interfacing in microprocessors. It discusses memory interfacing and I/O interfacing, and some of the peripheral devices developed by Intel like the 8255 parallel communication interface, 8251 serial communication interface, 8254 programmable timer, and 8257 DMA controller. It then describes serial and parallel communication interfaces. It provides details on the 8255 programmable peripheral interface and its operating modes. Finally, it discusses digital to analog converters, applications of the 8254 timer/counter, and analog to digital converters.
A tmega8 basics
The document provides an overview of the ATmega8 microcontroller, which is an 8-bit microcontroller based on the AVR RISC architecture. It can achieve throughput of up to 1 MIPS per MHz. The ATmega8 uses a Harvard architecture that separates program and data memories and buses. It has features such as 8K bytes of flash memory, 512 bytes of EEPROM, 1K byte of RAM, and three 8-bit I/O ports (Ports B, C, and D).
UNIT 3 Peripheral Interfacing.pptx
This document discusses memory and I/O interfacing in microprocessors. It describes the parallel communication interface 8255 which allows a microprocessor to interface with peripheral devices. The 8255 has three 8-bit ports that can be programmed to work in different modes like basic I/O, strobed I/O, and bidirectional modes. It reduces external logic needed for interfacing and can be programmed to perform specific functions through control words. The document also briefly mentions other programmable peripheral devices like serial interface 8251, timer 8254, and interrupt controller 8259.
8085 pin configuration
In this presentation you easily understand pin configuration of 8085 microprocessor and also easily delivered to the audience.
Peripherals and interfacing
This document provides an overview of peripherals and interfacing using various communication protocols. It discusses the I2C bus protocol for accessing peripheral chips. It covers the operation of the I2C bus including start/stop bits and acknowledgement. It then summarizes the use of various peripherals that interface using I2C including EEPROM, analog to digital converters, LCDs, and sensors. It also covers serial communication protocols like UART and interfacing for devices like keyboards.
8085 microprocessor
The 8085 is an 8-bit microprocessor that operates on a single +5V power supply. It has features like 16 address lines allowing access to 64KB of memory, 8 I/O address lines, and ability to operate at up to 3MHz clock frequency. The architecture of the 8085 includes registers like accumulator, flag, and program counter registers, an ALU, and functional blocks for instruction decoding, addressing, interrupts, and I/O. It has a 40-pin package with connections for power, data/address bus, control signals, interrupts, serial I/O, DMA and reset.
7 8255
The document discusses the 82C55 programmable peripheral interface chip. It can interface TTL-compatible I/O devices to microprocessors and is commonly used to interface keyboards and parallel printers in PCs. The 82C55 has 24 programmable I/O pins in groups of 12 and three operation modes: Mode 0 provides simple I/O; Mode 1 uses handshaking signals for strobed I/O; Mode 2 provides bi-directional bus I/O with handshaking. The document explains the pin definitions and signal timing for each mode. Programming and examples of using the 82C55 to interface displays, keyboards and other devices in various modes are also covered.
Ppi 8255
The 8255A Programmable Peripheral Interface allows for bidirectional communication between microprocessors and peripheral devices using three 8-bit ports that can be configured independently. It supports multiple operating modes including simple I/O, handshake-driven I/O, and bidirectional I/O. The document describes the features and architecture of the 8255A chip, its various ports and registers, and how it operates in different modes to transfer data with handshaking signals.
8255-PPI MPMC text book for engineering.ppt
The 8259A Programmable Interrupt Controller allows for 8 interrupt inputs to be handled individually. It can prioritize interrupts and mask lower priority interrupts while higher ones are serviced. The controller's pins include data bus pins to transfer control/status information, as well as pins for chip select, read/write, cascade connections for multiple controllers, and interrupt request/acknowledge lines. It provides flexible interrupt handling capabilities for microprocessors like the 8085A and 8086.
29. 8086 microprocessor pin diagram
The document describes the 8086 microprocessor. It has 16-bit data bus and 20-address lines that are time multiplexed. Some address lines are also multiplexed with status signals. It operates in minimum and maximum modes. In minimum mode, the 8086 generates control signals. In maximum mode, an 8288 bus controller generates control signals. The document details the pin descriptions and functions of the 8086 in both operating modes.
12 mt06ped001
The document discusses the architecture of the 8085 microprocessor. It describes that the 8085 is an 8-bit microprocessor introduced by Intel in the mid-1970s. It has 40 pins and can address up to 64KB of memory. The 8085 uses three buses - address bus, data bus, and control/status bus - to perform memory read, memory write, I/O read, and I/O write operations. It has registers like accumulator, flags, program counter, stack pointer and temporary registers. The arithmetic logic unit performs arithmetic and logic operations. It also describes the address buffer, interrupt control, and serial I/O capabilities of the 8085 microprocessor.
8086 new
The document provides information about microprocessors and the Intel 8086 microprocessor. It discusses the following:
- The functional blocks and registers of a typical microprocessor.
- An overview of the Intel 8086 including its introduction in 1978, transistor count, and operating modes.
- The pins and signals of the 8086 including address, data, control signals and minimum/maximum mode signals.
- The architecture of the 8086 including its bus interface unit, execution unit, registers, memory organization using segments and offsets, and addressing modes.
8086 complete guide
This is the ppt which covers the architecture,instruction set,interfacing with peripherals and many more topics .
PPI-MECHATRONICS
The document discusses various programmable peripheral interface chips used for input/output interfacing in microprocessor systems. It describes the architecture and operating modes of the 8255 Programmable Peripheral Interface chip, which has three 8-bit I/O ports that can be programmed for applications like keyboard interfacing, LED displays, analog-to-digital conversion, digital-to-analog conversion, temperature control, stepper motor control, and traffic light control systems. Circuit diagrams and software flowcharts are provided for different interfacing applications using the 8255 PPI chip.
The presentation is about USART and serial communication
This document provides an overview of serial communication and the Universal Asynchronous Receiver-Transmitter (USART) used in PIC18 microcontrollers. It discusses serial versus parallel data transmission, asynchronous and synchronous serial communication, the USART registers used for serial communication in PIC18, and examples of programming the USART for transmission and reception. The USART allows serial communication by converting parallel data from the microcontroller to serial bits for transmission over a single line and vice versa.
Basics of ATmega32
The document provides an overview of the ATMega32 microcontroller. It describes the microcontroller's key features which include being 8-bit, low-power, and having 32Kbytes of programmable flash memory. It also outlines the microcontroller's ports, power sources, and oscillator options. Programming tools that can be used with the ATMega32 like various compilers and hardware programmers are also listed.
Programmableperipheralinterface 8255 ppt
The 8255 Programmable Peripheral Interface is a programmable device with 24 I/O pins that can be configured for input or output. It contains ports A, B, and C that can be programmed to operate in different I/O modes including mode 0 for simple I/O, mode 1 for handshaking, and mode 2 for bidirectional transfers. The device uses control registers to define the I/O mode and configuration of each port.
AVR programming - BASICS
The document discusses the features and input/output basics of the AVR ATmega16 microcontroller. Key points include its Harvard architecture, 8-bit design, timers, ADC, and protocol support. It describes compiler tools, programming hardware, and pin configuration registers like DDR, PORT, and PIN. The DDR register sets the pin directions, PORT is used for output and pull-up configuration, and PIN reads pin states. Pull-up resistors prevent floating inputs. An exercise demonstrates configuring ports for different I/O functions.
8255 Programmable parallel I/O
This document discusses programmable peripheral interface devices that use handshake signals for data input and output. It focuses on the 8255 programmable interface, which has 3 ports (A, B, C) that can be programmed for different I/O schemes. Port C can be used as individual bits or two 4-bit ports. The 8255 supports bit set/reset of port C and 3 modes - simple I/O, I/O with handshake, and bidirectional I/O. Modes 1 and 2 use control signals on port C like STB, IBF, ACK for handshake-based input/output with ports A and B.
Similar to Minmax (20)
The presentation is about USART and serial communication
The presentation is about USART and serial communication
More from HarshitParkar6677
Wi fi hacking
Chances are you have a Wi-Fi network at home, or live close to one (or more) that tantalizingly pops up in a list whenever you boot up the laptop.
The problem is, if there's a lock next to the network name (AKA the SSID, or service set identifier), that indicates security is activated. Without the password or passphrase, you're not going to get access to that network, or the sweet, sweet internet that goes with it.
D dos attack
A distributed denial-of-service (DDoS) attack is a malicious attempt to disrupt normal traffic of a targeted server, service or network by overwhelming the target or its surrounding infrastructure with a flood of Internet traffic. DDoS attacks achieve effectiveness by utilizing multiple compromised computer systems as sources of attack traffic. Exploited machines can include computers and other networked resources such as IoT devices. From a high level, a DDoS attack is like a traffic jam clogging up with highway, preventing regular traffic from arriving at its desired destination.
Notes chapter 6
A microprocessor is an electronic component that is used by a computer to do its work. It is a central processing unit on a single integrated circuit chip containing millions of very small components including transistors, resistors, and diodes that work together.
Interface notes
A microprocessor is an electronic component that is used by a computer to do its work. It is a central processing unit on a single integrated circuit chip containing millions of very small components including transistors, resistors, and diodes that work together.
Chapter6 2
A microprocessor is an electronic component that is used by a computer to do its work. It is a central processing unit on a single integrated circuit chip containing millions of very small components including transistors, resistors, and diodes that work together.
Chapter6
There are two methods for interfacing memory and I/O devices with a microprocessor: I/O mapped I/O and memory mapped I/O. I/O mapped I/O treats I/O devices and memory separately, while memory mapped I/O treats I/O devices as memory. I/O mapped I/O can use either 8 or 16 address lines, allowing connection of up to 256 fixed I/O devices or 65,536 variable I/O devices. Specific instructions like IN, OUT, and MOV are used to access I/O ports depending on whether it is fixed or variable addressing.
8086 cpu 1
A microprocessor is an electronic component that is used by a computer to do its work. It is a central processing unit on a single integrated circuit chip containing millions of very small components including transistors, resistors, and diodes that work together.
Chapter 6 notes
A microprocessor is an electronic component that is used by a computer to do its work. It is a central processing unit on a single integrated circuit chip containing millions of very small components including transistors, resistors, and diodes that work together.
Chapter 5 notes
This document discusses procedures, macros, and stack operations in assembly language. It explains that procedures allow repetitive code to be written once and called multiple times to save memory. Procedures use stack operations to push return addresses and data onto the stack. Macros simplify programming by reducing repetitive code. Procedures are called at runtime, while macro calls are replaced with their body at assembly time.
Chap6 procedures & macros
A microprocessor is an electronic component that is used by a computer to do its work. It is a central processing unit on a single integrated circuit chip containing millions of very small components including transistors, resistors, and diodes that work together.
Chapter 5 notes new
Procedures and macros allow code to be reused in assembly language programs. Procedures are subroutines that are called using CALL and RET instructions. Macros allow short, repetitive code sequences to be defined once and reused by replacing the macro call with its body code. Some key differences are that procedures occupy less memory than macros since macro code is generated each time, while procedures' code is only stored once. Procedures are accessed using CALL while macros are accessed by name.
Notes arithmetic instructions
A microprocessor is an electronic component that is used by a computer to do its work. It is a central processing unit on a single integrated circuit chip containing millions of very small components including transistors, resistors, and diodes that work together. Some microprocessors in the 20th century required several chips. Microprocessors help to do everything from controlling elevators to searching the Web. Everything a computer does is described by instructions of computer programs, and microprocessors carry out these instructions many millions of times a second. [1]
Microprocessors were invented in the 1970s for use in embedded systems. The majority are still used that way, in such things as mobile phones, cars, military weapons, and home appliances. Some microprocessors are microcontrollers, so small and inexpensive that they are used to control very simple products like flashlights and greeting cards that play music when you open them. A few especially powerful microprocessors are used in personal computers.
Notes all instructions
A microprocessor is an electronic component that is used by a computer to do its work. It is a central processing unit on a single integrated circuit chip containing millions of very small components including transistors, resistors, and diodes that work together. Some microprocessors in the 20th century required several chips. Microprocessors help to do everything from controlling elevators to searching the Web. Everything a computer does is described by instructions of computer programs, and microprocessors carry out these instructions many millions of times a second. [1]
Microprocessors were invented in the 1970s for use in embedded systems. The majority are still used that way, in such things as mobile phones, cars, military weapons, and home appliances. Some microprocessors are microcontrollers, so small and inexpensive that they are used to control very simple products like flashlights and greeting cards that play music when you open them. A few especially powerful microprocessors are used in personal computers.
Notes aaa aa
A microprocessor is an electronic component that is used by a computer to do its work. It is a central processing unit on a single integrated circuit chip containing millions of very small components including transistors, resistors, and diodes that work together. Some microprocessors in the 20th century required several chips. Microprocessors help to do everything from controlling elevators to searching the Web. Everything a computer does is described by instructions of computer programs, and microprocessors carry out these instructions many millions of times a second. [1]
Microprocessors were invented in the 1970s for use in embedded systems. The majority are still used that way, in such things as mobile phones, cars, military weapons, and home appliances. Some microprocessors are microcontrollers, so small and inexpensive that they are used to control very simple products like flashlights and greeting cards that play music when you open them. A few especially powerful microprocessors are used in personal computers.
Notes 8086 instruction format
A microprocessor is an electronic component that is used by a computer to do its work. It is a central processing unit on a single integrated circuit chip containing millions of very small components including transistors, resistors, and diodes that work together. Some microprocessors in the 20th century required several chips. Microprocessors help to do everything from controlling elevators to searching the Web. Everything a computer does is described by instructions of computer programs, and microprocessors carry out these instructions many millions of times a second. [1]
Microprocessors were invented in the 1970s for use in embedded systems. The majority are still used that way, in such things as mobile phones, cars, military weapons, and home appliances. Some microprocessors are microcontrollers, so small and inexpensive that they are used to control very simple products like flashlights and greeting cards that play music when you open them. A few especially powerful microprocessors are used in personal computers.
Misc
This document describes the Jcc family of conditional jump instructions in x86 assembly language. It provides the instruction name, description of the condition tested, and any alternative mnemonics or opposite instructions. The instructions test various CPU flags like carry, zero, sign, overflow, parity, and compare values based on signed or unsigned arithmetic.
Copy of 8086inst logical
A microprocessor is an electronic component that is used by a computer to do its work. It is a central processing unit on a single integrated circuit chip containing millions of very small components including transistors, resistors, and diodes that work together. Some microprocessors in the 20th century required several chips. Microprocessors help to do everything from controlling elevators to searching the Web. Everything a computer does is described by instructions of computer programs, and microprocessors carry out these instructions many millions of times a second. [1]
Microprocessors were invented in the 1970s for use in embedded systems. The majority are still used that way, in such things as mobile phones, cars, military weapons, and home appliances. Some microprocessors are microcontrollers, so small and inexpensive that they are used to control very simple products like flashlights and greeting cards that play music when you open them. A few especially powerful microprocessors are used in personal computers.
Copy of 8086inst logical
A microprocessor is an electronic component that is used by a computer to do its work. It is a central processing unit on a single integrated circuit chip containing millions of very small components including transistors, resistors, and diodes that work together. Some microprocessors in the 20th century required several chips. Microprocessors help to do everything from controlling elevators to searching the Web. Everything a computer does is described by instructions of computer programs, and microprocessors carry out these instructions many millions of times a second. [1]
Microprocessors were invented in the 1970s for use in embedded systems. The majority are still used that way, in such things as mobile phones, cars, military weapons, and home appliances. Some microprocessors are microcontrollers, so small and inexpensive that they are used to control very simple products like flashlights and greeting cards that play music when you open them. A few especially powerful microprocessors are used in personal computers.
Chapter3 program flow control instructions
A microprocessor is an electronic component that is used by a computer to do its work. It is a central processing unit on a single integrated circuit chip containing millions of very small components including transistors, resistors, and diodes that work together. Some microprocessors in the 20th century required several chips. Microprocessors help to do everything from controlling elevators to searching the Web. Everything a computer does is described by instructions of computer programs, and microprocessors carry out these instructions many millions of times a second. [1]
Microprocessors were invented in the 1970s for use in embedded systems. The majority are still used that way, in such things as mobile phones, cars, military weapons, and home appliances. Some microprocessors are microcontrollers, so small and inexpensive that they are used to control very simple products like flashlights and greeting cards that play music when you open them. A few especially powerful microprocessors are used in personal computers.
Chapter3 8086inst stringsl
A microprocessor is an electronic component that is used by a computer to do its work. It is a central processing unit on a single integrated circuit chip containing millions of very small components including transistors, resistors, and diodes that work together. Some microprocessors in the 20th century required several chips. Microprocessors help to do everything from controlling elevators to searching the Web. Everything a computer does is described by instructions of computer programs, and microprocessors carry out these instructions many millions of times a second. [1]
Microprocessors were invented in the 1970s for use in embedded systems. The majority are still used that way, in such things as mobile phones, cars, military weapons, and home appliances. Some microprocessors are microcontrollers, so small and inexpensive that they are used to control very simple products like flashlights and greeting cards that play music when you open them. A few especially powerful microprocessors are used in personal computers.
More from HarshitParkar6677 (20)
Recently uploaded
Software Engineering and Project Management - Introduction, Modeling Concepts...
Introduction, Modeling Concepts and Class Modeling: What is Object orientation? What is OO development? OO Themes; Evidence for usefulness of OO development; OO modeling history. Modeling
as Design technique: Modeling, abstraction, The Three models. Class Modeling: Object and Class Concept, Link and associations concepts, Generalization and Inheritance, A sample class model, Navigation of class models, and UML diagrams
Building the Analysis Models: Requirement Analysis, Analysis Model Approaches, Data modeling Concepts, Object Oriented Analysis, Scenario-Based Modeling, Flow-Oriented Modeling, class Based Modeling, Creating a Behavioral Model.
KuberTENes Birthday Bash Guadalajara - K8sGPT first impressions
K8sGPT is a tool that analyzes and diagnoses Kubernetes clusters. This presentation was used to share the requirements and dependencies to deploy K8sGPT in a local environment.
International Conference on NLP, Artificial Intelligence, Machine Learning an...
International Conference on NLP, Artificial Intelligence, Machine Learning and Applications (NLAIM 2024) offers a premier global platform for exchanging insights and findings in the theory, methodology, and applications of NLP, Artificial Intelligence, Machine Learning, and their applications. The conference seeks substantial contributions across all key domains of NLP, Artificial Intelligence, Machine Learning, and their practical applications, aiming to foster both theoretical advancements and real-world implementations. With a focus on facilitating collaboration between researchers and practitioners from academia and industry, the conference serves as a nexus for sharing the latest developments in the field.
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...
Climate change's impact on the planet forced the United Nations and governments to promote green energies and electric transportation. The deployments of photovoltaic (PV) and electric vehicle (EV) systems gained stronger momentum due to their numerous advantages over fossil fuel types. The advantages go beyond sustainability to reach financial support and stability. The work in this paper introduces the hybrid system between PV and EV to support industrial and commercial plants. This paper covers the theoretical framework of the proposed hybrid system including the required equation to complete the cost analysis when PV and EV are present. In addition, the proposed design diagram which sets the priorities and requirements of the system is presented. The proposed approach allows setup to advance their power stability, especially during power outages. The presented information supports researchers and plant owners to complete the necessary analysis while promoting the deployment of clean energy. The result of a case study that represents a dairy milk farmer supports the theoretical works and highlights its advanced benefits to existing plants. The short return on investment of the proposed approach supports the paper's novelty approach for the sustainable electrical system. In addition, the proposed system allows for an isolated power setup without the need for a transmission line which enhances the safety of the electrical network
Comparative analysis between traditional aquaponics and reconstructed aquapon...
The aquaponic system of planting is a method that does not require soil usage. It is a method that only needs water, fish, lava rocks (a substitute for soil), and plants. Aquaponic systems are sustainable and environmentally friendly. Its use not only helps to plant in small spaces but also helps reduce artificial chemical use and minimizes excess water use, as aquaponics consumes 90% less water than soil-based gardening. The study applied a descriptive and experimental design to assess and compare conventional and reconstructed aquaponic methods for reproducing tomatoes. The researchers created an observation checklist to determine the significant factors of the study. The study aims to determine the significant difference between traditional aquaponics and reconstructed aquaponics systems propagating tomatoes in terms of height, weight, girth, and number of fruits. The reconstructed aquaponics system’s higher growth yield results in a much more nourished crop than the traditional aquaponics system. It is superior in its number of fruits, height, weight, and girth measurement. Moreover, the reconstructed aquaponics system is proven to eliminate all the hindrances present in the traditional aquaponics system, which are overcrowding of fish, algae growth, pest problems, contaminated water, and dead fish.
Embedded machine learning-based road conditions and driving behavior monitoring
Car accident rates have increased in recent years, resulting in losses in human lives, properties, and other financial costs. An embedded machine learning-based system is developed to address this critical issue. The system can monitor road conditions, detect driving patterns, and identify aggressive driving behaviors. The system is based on neural networks trained on a comprehensive dataset of driving events, driving styles, and road conditions. The system effectively detects potential risks and helps mitigate the frequency and impact of accidents. The primary goal is to ensure the safety of drivers and vehicles. Collecting data involved gathering information on three key road events: normal street and normal drive, speed bumps, circular yellow speed bumps, and three aggressive driving actions: sudden start, sudden stop, and sudden entry. The gathered data is processed and analyzed using a machine learning system designed for limited power and memory devices. The developed system resulted in 91.9% accuracy, 93.6% precision, and 92% recall. The achieved inference time on an Arduino Nano 33 BLE Sense with a 32-bit CPU running at 64 MHz is 34 ms and requires 2.6 kB peak RAM and 139.9 kB program flash memory, making it suitable for resource-constrained embedded systems.
Data Driven Maintenance | UReason Webinar
Discover the latest insights on Data Driven Maintenance with our comprehensive webinar presentation. Learn about traditional maintenance challenges, the right approach to utilizing data, and the benefits of adopting a Data Driven Maintenance strategy. Explore real-world examples, industry best practices, and innovative solutions like FMECA and the D3M model. This presentation, led by expert Jules Oudmans, is essential for asset owners looking to optimize their maintenance processes and leverage digital technologies for improved efficiency and performance. Download now to stay ahead in the evolving maintenance landscape.
Hematology Analyzer Machine - Complete Blood Count
The CBC machine is a common diagnostic tool used by doctors to measure a patient's red blood cell count, white blood cell count and platelet count. The machine uses a small sample of the patient's blood, which is then placed into special tubes and analyzed. The results of the analysis are then displayed on a screen for the doctor to review. The CBC machine is an important tool for diagnosing various conditions, such as anemia, infection and leukemia. It can also help to monitor a patient's response to treatment.
学校原版美国波士顿大学毕业证学历学位证书原版一模一样
原版一模一样【微信：741003700 】【美国波士顿大学毕业证学历学位证书】【微信：741003700 】学位证，留信认证（真实可查，永久存档）offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原海外各大学 Bachelor Diploma degree, Master Degree Diploma
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问Q/微741003700
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
LLM Fine Tuning with QLoRA Cassandra Lunch 4, presented by Anant
Slides for the 4th Presentation on LLM Fine-Tuning with QLoRA Presented by Anant, featuring DataStax Astra
官方认证美国密歇根州立大学毕业证学位证书原版一模一样
原版一模一样【微信：741003700 】【美国密歇根州立大学毕业证学位证书】【微信：741003700 】学位证，留信认证（真实可查，永久存档）offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原海外各大学 Bachelor Diploma degree, Master Degree Diploma
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问Q/微741003700
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
The Python for beginners. This is an advance computer language.
Python language is very important language at this time. we can easily understand this language by these notes.
AI assisted telemedicine KIOSK for Rural India.pptx
It gives the overall description of SIH problem statement " AI assisted telemedicine KIOSK for Rural India".
Recently uploaded (20)
Software Engineering and Project Management - Introduction, Modeling Concepts...
Software Engineering and Project Management - Introduction, Modeling Concepts...
KuberTENes Birthday Bash Guadalajara - K8sGPT first impressions
KuberTENes Birthday Bash Guadalajara - K8sGPT first impressions
International Conference on NLP, Artificial Intelligence, Machine Learning an...
International Conference on NLP, Artificial Intelligence, Machine Learning an...
Introduction to AI Safety (public presentation).pptx
Introduction to AI Safety (public presentation).pptx
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...
Comparative analysis between traditional aquaponics and reconstructed aquapon...
Comparative analysis between traditional aquaponics and reconstructed aquapon...
4. Mosca vol I -Fisica-Tipler-5ta-Edicion-Vol-1.pdf
4. Mosca vol I -Fisica-Tipler-5ta-Edicion-Vol-1.pdf
Embedded machine learning-based road conditions and driving behavior monitoring
Embedded machine learning-based road conditions and driving behavior monitoring
Hematology Analyzer Machine - Complete Blood Count
Hematology Analyzer Machine - Complete Blood Count
LLM Fine Tuning with QLoRA Cassandra Lunch 4, presented by Anant
LLM Fine Tuning with QLoRA Cassandra Lunch 4, presented by Anant
The Python for beginners. This is an advance computer language.
The Python for beginners. This is an advance computer language.
AI assisted telemedicine KIOSK for Rural India.pptx
AI assisted telemedicine KIOSK for Rural India.pptx
Minmax
- 1. IC245 Bidirectional Buffer •Also called as Octal bus Transceiver •Bidirectional bus increases the current driving capacity of data bus •Each buffer can sink 24mA and source 15mA. •Consists of 16 non inverting buffers, eight for each direction with tri-state outputs. •G is the enable pin, when G=0,DIR is chosen. •Direction of data pin decided by DIR pin •When DIR = 1, Data A bus B bus •When DIR =0, Data B bus A bus
- 2. IC373 Octal latch •Used for the separation of valid addresses from address/data bus •Controlled by the ALE signal of microprocessor •Latch is controlled by E input (STB input) which is connected to the clock input of D f/f. •Buffer is controlled by OE pin
- 3. Minimum Mode of 8086 Based System Octal Latch Transceiver
- 4. Minimum Mode Read bus cycle
- 5. Minimum Mode Write bus cycle
- 6. Maximum Mode of 8086 Based System Octal Latch Transceiver
- 7. Maximum Mode Read bus cycle
- 8. Maximum Mode Write bus cycle