The document proposes a new routing protocol called Optimal, Adaptive and Energy driven Mesh Routing Protocol (OAEMRP) for virtualized wireless sensor networks (VSNs). OAEMRP aims to reduce energy consumption and improve network lifetime compared to existing protocols like newEMRP. It does this by limiting the number of broadcast messages during relay node selection and giving equal weight to factors like energy, distance, and angle when choosing relay paths. Simulation results show OAEMRP achieves lower energy consumption, longer network lifetime, and lower packet loss than newEMRP and other similar protocols.
GRAPH THEORETIC ROUTING ALGORITHM (GTRA) FOR MOBILE AD-HOC NETWORKS (MANET)graphhoc
Battlefield theater applications require supporting large number of nodes. It can facilitate many multi-hop
paths between each source and destination pairs. For scalability, it is critical that for supporting network
centric applications with large set of nodes require hierarchical approach to designing networks. In this
research we consider using Mobile Ad Hoc Network (MANET) with multiple clusters. Each cluster
supports a few nodes with a cluster head. The intra-cluster connectivity amongst the nodes within the
cluster is supported by multi-hop connectivity to ensure handling mobility in such a way that no service
disruption can occur. The inter-cluster connectivity is also achieved by multi-hop connectivity. However,
for inter-cluster communications, only cluster heads are connected. The selection of intra-cluster
communications and inter-cluster communications allow scalability of the network to support multiservices
applications end-to-end with a desired Quality of Service (QoS). This paper proposes graph
theoretic approach to establish efficient connection between a source and a destination within each cluster
in intra-cluster network and between clusters in inter-cluster network. Graph theoretic approach
traditionally was applied networks where nodes are static or fixed. In this paper, we have applied the
graph theoretic routing to MANET where nodes are mobile. One of the important challenges in MANET is
to support an efficient routing algorithm for multi-hop communications across many nodes which are
dynamic in nature. However, dynamic behavior of the nodes requires greater understanding of the node
degree and mobility at each instance of time in order to maintain end-to-end QoS for multi-service
provisioning. This paper demonstrates graph theoretic approach produces an optimum multi-hop
connectivity path based on cumulative minimum degree that minimizes the contention and scheduling
delay end-to-end. It is applied to both intra-cluster communications as well as inter-cluster
communications. The performance shows that having a multi-hop connectivity for intra-cluster
communications is more power efficient compared to broadcast of information with maximum power
coverage. Each cluster performs similarly and the algorithm is also used for inter-cluster communications.
Our simulation results show that the proposed graph theoretic routing approach will reduce the overall
delay and improves the physical layer data frame transmission.
Improved routing scheme with ACO in WSN in comparison to DSDVijsrd.com
Routing is the process of selecting best paths in a network in terms of energy and distance. In adhoc it is critical to collect the information in an efficient manner as it has limitations in terms of centralized congestion. In such case to perform the effective communication there is the requirement of some such routing approach that can provide the routing with optimized path. In this work, ACO based routing approach is defined to generate the optimized path in comparison to DSDV over the network. The presented approach is implemented in matlab environment and obtained results shows the effective results in terms of optimized path.
Comparative Simulation Study Of LEACH-Like And HEED-Like Protocols Deployed I...IOSRJECE
WSNs represents one of the most interesting research areas with deep impact on technological development because of their potential usage in a wide variety of applications such as fire monitoring, border surveillance medical care, and highway traffic coordination. Therefore, WSNs researchers have defined many routing protocols for this type of network. In this paper, we have implemented and analyzed different clustering protocols, namely LEACH, LEACH-C, LEACH-1R, and HEED using MATLAB environment. These routing protocols are compared in different terms such as residual energy, data delivery to the base station, number of rounds and live nodes
GRAPH THEORETIC ROUTING ALGORITHM (GTRA) FOR MOBILE AD-HOC NETWORKS (MANET)graphhoc
Battlefield theater applications require supporting large number of nodes. It can facilitate many multi-hop
paths between each source and destination pairs. For scalability, it is critical that for supporting network
centric applications with large set of nodes require hierarchical approach to designing networks. In this
research we consider using Mobile Ad Hoc Network (MANET) with multiple clusters. Each cluster
supports a few nodes with a cluster head. The intra-cluster connectivity amongst the nodes within the
cluster is supported by multi-hop connectivity to ensure handling mobility in such a way that no service
disruption can occur. The inter-cluster connectivity is also achieved by multi-hop connectivity. However,
for inter-cluster communications, only cluster heads are connected. The selection of intra-cluster
communications and inter-cluster communications allow scalability of the network to support multiservices
applications end-to-end with a desired Quality of Service (QoS). This paper proposes graph
theoretic approach to establish efficient connection between a source and a destination within each cluster
in intra-cluster network and between clusters in inter-cluster network. Graph theoretic approach
traditionally was applied networks where nodes are static or fixed. In this paper, we have applied the
graph theoretic routing to MANET where nodes are mobile. One of the important challenges in MANET is
to support an efficient routing algorithm for multi-hop communications across many nodes which are
dynamic in nature. However, dynamic behavior of the nodes requires greater understanding of the node
degree and mobility at each instance of time in order to maintain end-to-end QoS for multi-service
provisioning. This paper demonstrates graph theoretic approach produces an optimum multi-hop
connectivity path based on cumulative minimum degree that minimizes the contention and scheduling
delay end-to-end. It is applied to both intra-cluster communications as well as inter-cluster
communications. The performance shows that having a multi-hop connectivity for intra-cluster
communications is more power efficient compared to broadcast of information with maximum power
coverage. Each cluster performs similarly and the algorithm is also used for inter-cluster communications.
Our simulation results show that the proposed graph theoretic routing approach will reduce the overall
delay and improves the physical layer data frame transmission.
Improved routing scheme with ACO in WSN in comparison to DSDVijsrd.com
Routing is the process of selecting best paths in a network in terms of energy and distance. In adhoc it is critical to collect the information in an efficient manner as it has limitations in terms of centralized congestion. In such case to perform the effective communication there is the requirement of some such routing approach that can provide the routing with optimized path. In this work, ACO based routing approach is defined to generate the optimized path in comparison to DSDV over the network. The presented approach is implemented in matlab environment and obtained results shows the effective results in terms of optimized path.
Comparative Simulation Study Of LEACH-Like And HEED-Like Protocols Deployed I...IOSRJECE
WSNs represents one of the most interesting research areas with deep impact on technological development because of their potential usage in a wide variety of applications such as fire monitoring, border surveillance medical care, and highway traffic coordination. Therefore, WSNs researchers have defined many routing protocols for this type of network. In this paper, we have implemented and analyzed different clustering protocols, namely LEACH, LEACH-C, LEACH-1R, and HEED using MATLAB environment. These routing protocols are compared in different terms such as residual energy, data delivery to the base station, number of rounds and live nodes
DOTNET 2013 IEEE MOBILECOMPUTING PROJECT Optimal multicast capacity and delay...IEEEGLOBALSOFTTECHNOLOGIES
To Get any Project for CSE, IT ECE, EEE Contact Me @ 09849539085, 09966235788 or mail us - ieeefinalsemprojects@gmail.com-Visit Our Website: www.finalyearprojects.org
ROUTING IN OPTICAL MESH NETWORKS-A QOS PERSPECTIVEijasuc
Wireless Ad-Hoc Mesh Networks are characterized by static nodes connected in a mesh topology. A routing
protocol discovers and maintains the route for successful transmission of data in a network. The routing
protocol should also provide load balancing and fault tolerance for improved network performance. In
Free Space Optical networks (FSO) line of sight (LOS) should be maintained between the two
communicating nodes. In a multihop scenario maintaining LOS during routing is a challenge. In this paper
we propose a routing protocol Quality of Service-Directional Routing Protocol (QDRP) - which assures a
certain level of performance to a data flow in terms of delay and implemented on FSO MANET. Through
simulations it is observed that QDRP chooses the path with the least delay and performs satisfactorily
under varying node densities and transmission rates achieving end to end delay of .14 s and packet delivery
percentage of 96% when simulated for an area of 1300 m *1300 m for 100 nodes. This work explores the
potential of the proposed routing protocol for free space optical mesh networks. QDRP is compared with
ORRP (Orthogonal Rendezvous Routing Protocol) and AODV (Ad-Hoc on Demand Distance Vector), a
reactive protocol which is also implemented in free space optical environment. We support our conclusions
that QDRP gains in terms of packet delivery percentage, end to end delay and goodput.
MANET Routing Protocols , a case studyRehan Hattab
L. Yi, Y. Zhai, Y. Wang, J. Yuan and I. You , Impacts of Internal Network Contexts on Performance of MANET Routing Protocols: a Case Study, Sixth International Conference on Innovative Mobile and Internet Services in Ubiquitous Computing,2012.
Hybrid networks is integrate MANETs and infrastructure wireless networks
It have proven to be a better network structure for the next generation networks
It can act Base station and Ad hoc according to the environment conditions
The widespread use of mobile devices the increasing demand for mobile multimedia streaming services
The future of real time need of high Quality of Service (QoS) support in wireless and mobile networking environments
The QoS support reduces end to end transmission delay and enhances throughput to guarantee the seamless communication between mobile devices and wireless infrastructures
Specifically, infrastructure networks improve the scalability of MANETs, while MANETs automatically establish self-organizing networks, extending the coverage of the infrastructure networks
PERFORMANCE ANALYSIS OF CHANNEL ACCESS MODEL FOR MAC IN RANDOMLY DISTRIBUTED ...IJCNCJournal
Medium Access control (MAC) is one of the fundamental problems in wireless sensor networks. The performance of wireless sensor network depends on it. The main objective of a medium access control method is to provide high throughput, minimize the delay, and conservers the energy consumption by avoiding the collisions. In this paper, a general model for MAC protocol to reduce the delay, maximize throughput and conserve the energy consumption in channel accessing in high density randomly distributed wireless sensor network is presented. The proposed model is simulated using MATLAB. The simulation results show that the average delay for sensors with sufficient memory is lower than sensors without
memory. Further, the throughput of the channel access method with memory is better than without memory.
INCREASE THE LIFETIME OF WIRELESS SENSOR NETWORKS USING HIERARCHICAL CLUSTERI...ijwmn
Wireless sensor networks consist of hundreds or thousands of nodes with limited energy. Since the life time
of each sensor is equivalent to the battery life, the energy issue is considered as a major challenge.
Clustering has been proposed as a strategy to extend the lifetime of wireless sensor networks. Cluster size,
number of Cluster head per cluster and the selection of cluster head are considered as important factors in
clustering. In this research by studying LEACH algorithm and optimized algorithms of this protocol and by
evaluating the strengths and weaknesses, a new algorithm based on hierarchical clustering to increase the
lifetime of the sensor network is proposed. In this study, with a special mechanism the environment of
network is layered and the optimal number of cluster head in each layer is selected and then recruit for the
formation of clusters in the same layer by controlling the topology of the clusters is done independently.
Then the data is sent through the by cluster heads through the multi- stage to the main station. Simulation
results show that the above mentioned method increases the life time about 70% compared to the LEACH.
Energy balanced improved leach routing protocol for wireless sensor networkscsandit
A proper sensor node clustering is an effective topology control that can balance energy
consumption among sensor nodes and increase network scalability and life time. As the use of
wireless sensor networks (WSNs) has grown enormously, the need for energy-efficient routing
and data aggregation has also risen. LEACH
(
Low Energy Adaptive Cluster Hierarchy
)
is a
hierarchical clustering protocol that provides an elegant solution for such protocols. Random
clustering is the main deficiency of LEACH. In this paper an energy balanced clustering
approach is proposed, in which the K-mean clustering algorithm is applied. It is centralized
clustering algorithm that based on minimum energy clustering to form optimal clusters. For the
candidate nodes, the location and the residual energy are used as key parameters to select the
cluster head (CH). The method shows that the proposed approach outperforms LEACH in terms
of energy conservation and network life time prolonging.
Simulation Based Routing Protocols Evaluation for IEEE 802.15.4 enabled Wirel...IDES Editor
Wireless sensor network (WSN) is emerging as a
major research field in computer networks over the last decade
due to its wide variety of embedded real time applications.
Sensor networks have infrastructure-less architecture because
of frequently varying topology and link status. Routing is an
extremely challenging task for battery-powered resourceconstrained
WSN, since it is main cause for energy depletion
and energy must be utilized prudently to enhance lifetime
for sensor networks. This drives a myriad of research efforts
aiming at efficient data dissemination. In this paper we
analyze how efficiently MANET specific routing protocols
OLSR (Optimized Link-State Routing protocol), DYMO
(Dynamic MANET On-demand) and ZRP (Zone Routing
Protocol) perform in IEEE 802.15.4 enabled wireless sensor
networks and evaluate their simulation results using Qualnet
simulator. Several simulations were carried out under varying
network size and offered load for performance evaluation and
relative comparison of protocols is reported in terms of average
end to end delay, throughput and jitter.
Qo s oriented distributed routing protocols : anna university 2nd review pptAAKASH S
To find a QoS path between source and destination, Which satisfies
The QoS requirements for each admitted connection and
Optimizes the use of network resources
Quality encompasses the data loss, latency, jitter, efficient use of network resources,..
QoS mechanisms for unfairness: managing queuing behavior, shaping traffic, control admission, routing, …
Usually, a hybrid network has widespread base stations
The data transmission in hybrid networks has two features:
An AP can be a source or a destination to any mobile node
It allows a stream to have anycast transmission along multiple transmission paths to its destination through base stations
The number of transmission hops between a mobile node and an AP is small
It enables a source node to connect to an AP through an intermediate node
In this paper introduce the QoS-Oriented Distributed routing protocol(QOD)
This QOD protocol makes five contributions:
QoS-guaranteed neighbor selection algorithm
Distributed packet scheduling algorithm
Mobility-based segment resizing algorithm
Soft-deadline based forwarding scheduling algorithm
Data redundancy elimination based transmission
An effective transmit packet coding with trust-based relay nodes in VANETsjournalBEEI
Vehicular ad-hoc networks (VANETs) are characterized by limited network resources such as limited bandwidth and battery capacity. Hence, it is necessary that unnecessary use of network resources (such as unnecessary packet transfers) is reduced in such networks so that the available power can be conserved for efficient multicast communications. In this paper, we have presented a Transmit Packet Coding (TPC) Network Coding in VANET to ensure reliable and efficient multicasting. With network coding, the number of transmitted packets over the network can be reduced, ensuring efficient utilization of network devices and resources. Here, the trust-based graph optimization is performed using Cuckoo search algorithm to select the secure relay nodes. The experimental results showed the superiority of the presented approach compared to the existing techniques in terms of throughput, latency, hop delay, packet delivery ratio, network decoder outage probability, and block error rate.
we find out various power aware and data packet rate control with-collision-avoidance (CSMA/CA)-based ad hoc wireless network communication. And identifies that CSMA
Performance Evaluation of a Layered WSN Using AODV and MCF Protocols in NS-2csandit
In layered networks, reliability is a major concern
as link failures at lower layer will have a
great impact on network reliability. Failure at a l
ower layer may lead to multiple failures at the
upper layers which deteriorate the network performa
nce. In this paper, the scenario of such a
layered wireless sensor network is considered for A
d hoc On-Demand Distance Vector (AODV)
and Multi Commodity Flow (MCF) routing protocols. M
CF is
developed using
polynomial time
approximation algorithms for the failure polynomial
. Both protocols are compared in terms of
different network parameters such as throughput, pa
cket loss and end to end delay. It was
shown that the network reliability is better when M
CF protocol is used. It was also shown that
maximizing the min cut of the layered network maxim
izes reliability in the terms of successful
packet transmission of network. Thetwo routing prot
ocolsare implemented in the scenario of
discrete network event simulator NS-2.
An Improved Energy Efficient Wireless Sensor Networks Through Clustering In C...Editor IJCATR
One of the major reason for performance degradation in Wireless sensor network is the overhead due to control packet and
packet delivery degradation. Clustering in cross layer network operation is an efficient way manage control packet overhead and which
ultimately improve the lifetime of a network. All these overheads are crucial in a scalable networks. But the clustering always suffer
from the cluster head failure which need to be solved effectively in a large network. As the focus is to improve the average lifetime of
sensor network the cluster head is selected based on the battery life of nodes. The cross-layer operation model optimize the overheads
in multiple layer and ultimately the use of clustering will reduce the major overheads identified and their by the energy consumption
and throughput of wireless sensor network is improved. The proposed model operates on two layers of network ie., Network Layer
and Transport Layer and Clustering is applied in the network layer . The simulation result shows that the integration of two layers
reduces the energy consumption and increases the throughput of the wireless sensor networks.
An Improved Energy Efficient Wireless Sensor Networks Through Clustering In C...Editor IJCATR
One of the major reason for performance degradation in Wireless sensor network is the overhead due to control packet and
packet delivery degradation. Clustering in cross layer network operation is an efficient way manage control packet overhead and which
ultimately improve the lifetime of a network. All these overheads are crucial in a scalable networks. But the clustering always suffer
from the cluster head failure which need to be solved effectively in a large network. As the focus is to improve the average lifetime of
sensor network the cluster head is selected based on the battery life of nodes. The cross-layer operation model optimize the overheads
in multiple layer and ultimately the use of clustering will reduce the major overheads identified and their by the energy consumption
and throughput of wireless sensor network is improved. The proposed model operates on two layers of network ie., Network Layer
and Transport Layer and Clustering is applied in the network layer . The simulation result shows that the integration of two layers
reduces the energy consumption and increases the throughput of the wireless sensor networks.
DOTNET 2013 IEEE MOBILECOMPUTING PROJECT Optimal multicast capacity and delay...IEEEGLOBALSOFTTECHNOLOGIES
To Get any Project for CSE, IT ECE, EEE Contact Me @ 09849539085, 09966235788 or mail us - ieeefinalsemprojects@gmail.com-Visit Our Website: www.finalyearprojects.org
ROUTING IN OPTICAL MESH NETWORKS-A QOS PERSPECTIVEijasuc
Wireless Ad-Hoc Mesh Networks are characterized by static nodes connected in a mesh topology. A routing
protocol discovers and maintains the route for successful transmission of data in a network. The routing
protocol should also provide load balancing and fault tolerance for improved network performance. In
Free Space Optical networks (FSO) line of sight (LOS) should be maintained between the two
communicating nodes. In a multihop scenario maintaining LOS during routing is a challenge. In this paper
we propose a routing protocol Quality of Service-Directional Routing Protocol (QDRP) - which assures a
certain level of performance to a data flow in terms of delay and implemented on FSO MANET. Through
simulations it is observed that QDRP chooses the path with the least delay and performs satisfactorily
under varying node densities and transmission rates achieving end to end delay of .14 s and packet delivery
percentage of 96% when simulated for an area of 1300 m *1300 m for 100 nodes. This work explores the
potential of the proposed routing protocol for free space optical mesh networks. QDRP is compared with
ORRP (Orthogonal Rendezvous Routing Protocol) and AODV (Ad-Hoc on Demand Distance Vector), a
reactive protocol which is also implemented in free space optical environment. We support our conclusions
that QDRP gains in terms of packet delivery percentage, end to end delay and goodput.
MANET Routing Protocols , a case studyRehan Hattab
L. Yi, Y. Zhai, Y. Wang, J. Yuan and I. You , Impacts of Internal Network Contexts on Performance of MANET Routing Protocols: a Case Study, Sixth International Conference on Innovative Mobile and Internet Services in Ubiquitous Computing,2012.
Hybrid networks is integrate MANETs and infrastructure wireless networks
It have proven to be a better network structure for the next generation networks
It can act Base station and Ad hoc according to the environment conditions
The widespread use of mobile devices the increasing demand for mobile multimedia streaming services
The future of real time need of high Quality of Service (QoS) support in wireless and mobile networking environments
The QoS support reduces end to end transmission delay and enhances throughput to guarantee the seamless communication between mobile devices and wireless infrastructures
Specifically, infrastructure networks improve the scalability of MANETs, while MANETs automatically establish self-organizing networks, extending the coverage of the infrastructure networks
PERFORMANCE ANALYSIS OF CHANNEL ACCESS MODEL FOR MAC IN RANDOMLY DISTRIBUTED ...IJCNCJournal
Medium Access control (MAC) is one of the fundamental problems in wireless sensor networks. The performance of wireless sensor network depends on it. The main objective of a medium access control method is to provide high throughput, minimize the delay, and conservers the energy consumption by avoiding the collisions. In this paper, a general model for MAC protocol to reduce the delay, maximize throughput and conserve the energy consumption in channel accessing in high density randomly distributed wireless sensor network is presented. The proposed model is simulated using MATLAB. The simulation results show that the average delay for sensors with sufficient memory is lower than sensors without
memory. Further, the throughput of the channel access method with memory is better than without memory.
INCREASE THE LIFETIME OF WIRELESS SENSOR NETWORKS USING HIERARCHICAL CLUSTERI...ijwmn
Wireless sensor networks consist of hundreds or thousands of nodes with limited energy. Since the life time
of each sensor is equivalent to the battery life, the energy issue is considered as a major challenge.
Clustering has been proposed as a strategy to extend the lifetime of wireless sensor networks. Cluster size,
number of Cluster head per cluster and the selection of cluster head are considered as important factors in
clustering. In this research by studying LEACH algorithm and optimized algorithms of this protocol and by
evaluating the strengths and weaknesses, a new algorithm based on hierarchical clustering to increase the
lifetime of the sensor network is proposed. In this study, with a special mechanism the environment of
network is layered and the optimal number of cluster head in each layer is selected and then recruit for the
formation of clusters in the same layer by controlling the topology of the clusters is done independently.
Then the data is sent through the by cluster heads through the multi- stage to the main station. Simulation
results show that the above mentioned method increases the life time about 70% compared to the LEACH.
Energy balanced improved leach routing protocol for wireless sensor networkscsandit
A proper sensor node clustering is an effective topology control that can balance energy
consumption among sensor nodes and increase network scalability and life time. As the use of
wireless sensor networks (WSNs) has grown enormously, the need for energy-efficient routing
and data aggregation has also risen. LEACH
(
Low Energy Adaptive Cluster Hierarchy
)
is a
hierarchical clustering protocol that provides an elegant solution for such protocols. Random
clustering is the main deficiency of LEACH. In this paper an energy balanced clustering
approach is proposed, in which the K-mean clustering algorithm is applied. It is centralized
clustering algorithm that based on minimum energy clustering to form optimal clusters. For the
candidate nodes, the location and the residual energy are used as key parameters to select the
cluster head (CH). The method shows that the proposed approach outperforms LEACH in terms
of energy conservation and network life time prolonging.
Simulation Based Routing Protocols Evaluation for IEEE 802.15.4 enabled Wirel...IDES Editor
Wireless sensor network (WSN) is emerging as a
major research field in computer networks over the last decade
due to its wide variety of embedded real time applications.
Sensor networks have infrastructure-less architecture because
of frequently varying topology and link status. Routing is an
extremely challenging task for battery-powered resourceconstrained
WSN, since it is main cause for energy depletion
and energy must be utilized prudently to enhance lifetime
for sensor networks. This drives a myriad of research efforts
aiming at efficient data dissemination. In this paper we
analyze how efficiently MANET specific routing protocols
OLSR (Optimized Link-State Routing protocol), DYMO
(Dynamic MANET On-demand) and ZRP (Zone Routing
Protocol) perform in IEEE 802.15.4 enabled wireless sensor
networks and evaluate their simulation results using Qualnet
simulator. Several simulations were carried out under varying
network size and offered load for performance evaluation and
relative comparison of protocols is reported in terms of average
end to end delay, throughput and jitter.
Qo s oriented distributed routing protocols : anna university 2nd review pptAAKASH S
To find a QoS path between source and destination, Which satisfies
The QoS requirements for each admitted connection and
Optimizes the use of network resources
Quality encompasses the data loss, latency, jitter, efficient use of network resources,..
QoS mechanisms for unfairness: managing queuing behavior, shaping traffic, control admission, routing, …
Usually, a hybrid network has widespread base stations
The data transmission in hybrid networks has two features:
An AP can be a source or a destination to any mobile node
It allows a stream to have anycast transmission along multiple transmission paths to its destination through base stations
The number of transmission hops between a mobile node and an AP is small
It enables a source node to connect to an AP through an intermediate node
In this paper introduce the QoS-Oriented Distributed routing protocol(QOD)
This QOD protocol makes five contributions:
QoS-guaranteed neighbor selection algorithm
Distributed packet scheduling algorithm
Mobility-based segment resizing algorithm
Soft-deadline based forwarding scheduling algorithm
Data redundancy elimination based transmission
An effective transmit packet coding with trust-based relay nodes in VANETsjournalBEEI
Vehicular ad-hoc networks (VANETs) are characterized by limited network resources such as limited bandwidth and battery capacity. Hence, it is necessary that unnecessary use of network resources (such as unnecessary packet transfers) is reduced in such networks so that the available power can be conserved for efficient multicast communications. In this paper, we have presented a Transmit Packet Coding (TPC) Network Coding in VANET to ensure reliable and efficient multicasting. With network coding, the number of transmitted packets over the network can be reduced, ensuring efficient utilization of network devices and resources. Here, the trust-based graph optimization is performed using Cuckoo search algorithm to select the secure relay nodes. The experimental results showed the superiority of the presented approach compared to the existing techniques in terms of throughput, latency, hop delay, packet delivery ratio, network decoder outage probability, and block error rate.
we find out various power aware and data packet rate control with-collision-avoidance (CSMA/CA)-based ad hoc wireless network communication. And identifies that CSMA
Performance Evaluation of a Layered WSN Using AODV and MCF Protocols in NS-2csandit
In layered networks, reliability is a major concern
as link failures at lower layer will have a
great impact on network reliability. Failure at a l
ower layer may lead to multiple failures at the
upper layers which deteriorate the network performa
nce. In this paper, the scenario of such a
layered wireless sensor network is considered for A
d hoc On-Demand Distance Vector (AODV)
and Multi Commodity Flow (MCF) routing protocols. M
CF is
developed using
polynomial time
approximation algorithms for the failure polynomial
. Both protocols are compared in terms of
different network parameters such as throughput, pa
cket loss and end to end delay. It was
shown that the network reliability is better when M
CF protocol is used. It was also shown that
maximizing the min cut of the layered network maxim
izes reliability in the terms of successful
packet transmission of network. Thetwo routing prot
ocolsare implemented in the scenario of
discrete network event simulator NS-2.
An Improved Energy Efficient Wireless Sensor Networks Through Clustering In C...Editor IJCATR
One of the major reason for performance degradation in Wireless sensor network is the overhead due to control packet and
packet delivery degradation. Clustering in cross layer network operation is an efficient way manage control packet overhead and which
ultimately improve the lifetime of a network. All these overheads are crucial in a scalable networks. But the clustering always suffer
from the cluster head failure which need to be solved effectively in a large network. As the focus is to improve the average lifetime of
sensor network the cluster head is selected based on the battery life of nodes. The cross-layer operation model optimize the overheads
in multiple layer and ultimately the use of clustering will reduce the major overheads identified and their by the energy consumption
and throughput of wireless sensor network is improved. The proposed model operates on two layers of network ie., Network Layer
and Transport Layer and Clustering is applied in the network layer . The simulation result shows that the integration of two layers
reduces the energy consumption and increases the throughput of the wireless sensor networks.
An Improved Energy Efficient Wireless Sensor Networks Through Clustering In C...Editor IJCATR
One of the major reason for performance degradation in Wireless sensor network is the overhead due to control packet and
packet delivery degradation. Clustering in cross layer network operation is an efficient way manage control packet overhead and which
ultimately improve the lifetime of a network. All these overheads are crucial in a scalable networks. But the clustering always suffer
from the cluster head failure which need to be solved effectively in a large network. As the focus is to improve the average lifetime of
sensor network the cluster head is selected based on the battery life of nodes. The cross-layer operation model optimize the overheads
in multiple layer and ultimately the use of clustering will reduce the major overheads identified and their by the energy consumption
and throughput of wireless sensor network is improved. The proposed model operates on two layers of network ie., Network Layer
and Transport Layer and Clustering is applied in the network layer . The simulation result shows that the integration of two layers
reduces the energy consumption and increases the throughput of the wireless sensor networks.
An Improved Energy Efficient Wireless Sensor Networks Through Clustering In C...Editor IJCATR
One of the major reason for performance degradation in Wireless sensor network is the overhead due to control packet and packet delivery degradation. Clustering in cross layer network operation is an efficient way manage control packet overhead and which ultimately improve the lifetime of a network. All these overheads are crucial in a scalable networks. But the clustering always suffer from the cluster head failure which need to be solved effectively in a large network. As the focus is to improve the average lifetime of sensor network the cluster head is selected based on the battery life of nodes. The cross-layer operation model optimize the overheads in multiple layer and ultimately the use of clustering will reduce the major overheads identified and their by the energy consumption and throughput of wireless sensor network is improved. The proposed model operates on two layers of network ie., Network Layer and Transport Layer and Clustering is applied in the network layer . The simulation result shows that the integration of two layers reduces the energy consumption and increases the throughput of the wireless sensor networks.
An Improved Energy Efficient Wireless Sensor Networks Through Clustering In C...Editor IJCATR
One of the major reason for performance degradation in Wireless sensor network is the overhead due to control packet and packet delivery degradation. Clustering in cross layer network operation is an efficient way manage control packet overhead and which ultimately improve the lifetime of a network. All these overheads are crucial in a scalable networks. But the clustering always suffer from the cluster head failure which need to be solved effectively in a large network. As the focus is to improve the average lifetime of sensor network the cluster head is selected based on the battery life of nodes. The cross-layer operation model optimize the overheads in multiple layer and ultimately the use of clustering will reduce the major overheads identified and their by the energy consumption and throughput of wireless sensor network is improved. The proposed model operates on two layers of network ie., Network Layer and Transport Layer and Clustering is applied in the network layer . The simulation result shows that the integration of two layers reduces the energy consumption and increases the throughput of the wireless sensor networks.
A cross layer optimized reliable multicast routing protocol in wireless mesh ...ijdpsjournal
The Optimal way to create a protocol in Wireless Mesh Networks
is to take into account a cross layer due
to the interference among wireless transmissions.
In this paper
,
w
e focus on designing and implementing
a
reliable
multicast protocol
called Me
sh Reliable Multicast Protocol (MRMP).
A
recovery tree
built
dynamically
which is joining with
the multicast routing tree.
U
sing the recovery tree
the packet losses are
repaired locally
.
This Cross layer
Technique
between network layer (
multicast routing)
and transport layer
(
reliability) using simulation
results
prove
the effectiveness
and optimization
of
cross layer
in WMNs
compare with the conventional layer
M-EPAR to Improve the Quality of the MANETsIJERA Editor
In MANET, power aware is important challenge issue to improve the communication energy efficiency at individual nodes. We propose modified efficient power aware routing (M-EPAR), a new power aware routing protocol that increases the network lifetime of MANET. Designing a power aware routing algorithm or technique is one of the most important point considered in Mobile Ad Hoc Networks. These nodes are driven by reactive protocols where broadcasting is mandatory to form a path between two nodes. So in case of death of the node resulting out of less battery calls for re-routing. Since many existing techniques focuses on energy aware routing this paper presents combination of energy aware routing merged with link quality determined by packet drop rate. The proposed scheme has outperformed the existing technique in terms of packet delivery ratio, throughput and energy consumption.
IJERA (International journal of Engineering Research and Applications) is International online, ... peer reviewed journal. For more detail or submit your article, please visit www.ijera.com
A scalable and power efficient solution for routing in mobile ad hoc network ...ijmnct
Mobile Ad Hoc Network (MANET) is a very dynamic and infrastructure-less ad hoc network. The actual
network size depends on the application and the protocols developed for the routing for this kind of
networks should be scalable. MANET is a resource limited network and therefore the developed routing
algorithm for packet transmission should be power and bandwidth efficient. These kinds of dynamic
networks should operate with minimal management overhead. The management functionality of the
network increases with number of nodes and reduces the performance of the network. Here, in this paper,
we have designed all identical nodes in the cluster except the cluster head and this criterion reduces the
management burden on the network. Graph theoretic routing algorithm is used to develop route for packet
transmission by using the minimum resources. In this paper, we developed routing algorithm for cluster
based MANET and finds a path from source to destination using minimum cumulative degree path. Our
simulation results show that this routing algorithm provide efficient routing path with the increasing
number of nodes and uses multi-hop connectivity for intra-cluster to utilize minimum power for packet
transmission irrespective of number of nodes in the network.
A novel routing technique for mobile ad hoc networks (manet)ijngnjournal
Actual network size depends on the application and the protocols developed for the routing for this kind of
networks should be scalable and efficient. Each routing protocol should support small as well as large
scale networks very efficiently. As the number of node increase, it increases the management functionality
of the network. Graph theoretic approach traditionally was applied to networks where nodes are static or
fixed. In this paper, we have applied the graph theoretic routing to MANET where nodes are mobile. Here,
we designed all identical nodes in the cluster except the cluster head and this criterion reduces the
management burden on the network. Each cluster supports a few nodes with a cluster head. The intracluster
connectivity amongst the nodes within the cluster is supported by multi-hop connectivity to ensure
handling mobility in such a way that no service disruption can occur. The inter-cluster connectivity is also
achieved by multi-hop connectivity. However, for inter-cluster communications, only cluster heads are
connected. This paper demonstrates graph theoretic approach produces an optimum multi-hop connectivity
path based on cumulative minimum degree that minimizes the contention and scheduling delay end-toend.
It is applied to both intra-cluster communications as well as inter-cluster communications. The
performance shows that having a multi-hop connectivity for intra-cluster communications is more power
efficient compared to broadcast of information with maximum power coverage. We also showed the total
number of required intermediate nodes in the transmission from source to destination. However, dynamic
behavior of the nodes requires greater understanding of the node degree and mobility at each instance of
time in order to maintain end-to-end QoS for multi-service provisioning. Our simulation results show that
the proposed graph theoretic routing approach will reduce the overall delay and improves the physical
layer data frame transmission.
Advance in the WIRELESS SENSOR NETWORK (WISENET) technology is energy efficient routing protocols that promises a wide range of potential applications in both civilian and military areas. In the WISNET the sensor node have a limited transmission range and their processing and storage capabilities as well as their energy sources are limited. So the Equalized Cluster Head Election Routing Protocol (ECHERP) and PEGASIS with Double Cluster Head (PDCH) pursues energy conservation through balanced clustering for Energy Efficiency. In WSN, energy efficient routing protocol is important to increase the network lifetime. ECHERP and PDCH both protocol claims to be energy efficient.
Adaptive Routing in Wireless Sensor Networks: QoS Optimisation for Enhanced A...M H
One of the key challenges for research in wireless sensor networks is the development of routing protocols that provide application-specific service guarantees. This paper presents a new cluster-based Route Optimisation and Load-balancing protocol, called ROL, that uses various quality of service (QoS) metrics to meet application requirements. ROL combines several application requirements, specifically it attempts to provide an inclusive solution to prolong network life, provide timely message delivery and improve network robustness. It uses a combination of routing metrics that can be configured according to the priorities of user-level applications to improve overall network performance. To this end, an optimisation tool for balancing the communication resources for the constraints and priorities of user applications has been developed and Nutrient-flow-based Distributed Clustering (NDC), an algorithm for load balancing is proposed. NDC works seamlessly with any clustering algorithm to equalise, as far as possible, the diameter and the membership of clusters. This paper presents simulation results to show that ROL/NDC gives a higher network lifetime than other similar schemes, such Mires++. In simulation, ROL/NDC maintains a maximum of 7\% variation from the optimal cluster population, reduces the total number of set-up messages by up to 60%, reduces the end-to-end delay by up to 56%, and enhances the data delivery ratio by up to 0.98% compared to Mires++.
Similar to IRJET - Improving Energy Efficiency for EMRP Routing Protocol for Virtualization in Wireless Sensor Network (20)
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.