This document presents the results of an experimental study on the behaviour of concrete with partial replacement of cement with Ground Granulated Blast Furnace Slag (GGBS) and fine aggregate with copper slag. Concrete cubes, cylinders and prisms were cast with 0-15% replacement of cement with GGBS and 0-30% replacement of fine aggregate with copper slag. The compressive strength, split tensile strength, and flexural strength of the specimens were tested after 7 and 28 days of curing and compared to controlled concrete. The optimal replacement percentages found were 30% fine aggregate replaced with copper slag and 15% cement replaced with GGBS, which showed improvements in strength properties over controlled concrete.
Study of Macro level Properties of SCC using GGBS and Lime stone powderIJERD Editor
One of the major environmental concerns is the disposal of the waste materials and utilization of
industrial by products. Lime stone quarries will produce millions of tons waste dust powder every year. Having
considerable high degree of fineness in comparision to cement this material may be utilized as a partial
replacement to cement. For this purpose an experiment is conducted to investigate the possibility of using lime
stone powder in the production of SCC with combined use GGBS and how it affects the fresh and mechanical
properties of SCC. First SCC is made by replacing cement with GGBS in percentages like 10, 20, 30, 40, 50 and
by taking the optimum mix with GGBS lime stone powder is blended to mix in percentages like 5, 10, 15, 20 as
a partial replacement to cement. Test results shows that the SCC mix with combination of 30% GGBS and 15%
limestone powder gives maximum compressive strength and fresh properties are also in the limits prescribed by
the EFNARC.
EXPERIMENTAL AND ANALYTICAL STUDY OF PARTIALLY REPLACED WASTE MATERIALS IN RI...guruvignesh N
This present study aims to identify the most suitable material
to utilize in concrete pavement. Several studies have been conducted across the worldwide to identify properties of waste materials on concrete and environmental also. From the basis of different studies the waste materials to be selected and replaced partial manner instead of concrete components. utilize waste material in rigid pavement for low cost concreting purpose. The selected appropriate ranging is to be used for rigid pavement construction in the grade of M30 as per IRC 44. Various engineering properties were obtained by strength and durability analysis.
Experimental Investigation on Replacement of Cement in Concrete Partially by ...ijtsrd
Concrete is the most extremely used construction material within the world, which always uses natural resources like lime, aggregates and water. The production of cement in world has increased greatly, due to this cement production emission of CO2 gas has been increased tremendously, ultimately environmental pollution increased to very large extent. This affect to environment has been reduced by cement has been replaced by some supplementary materials like Dolamite Powder or Fly ash or GGBS and so on. Dolamite. Powder was conducted detailed study and lots of research work has been made on other waste materials and it is found there is a great future scope for research on Dolamite Powder as a replacement to cement, sand or both. Now in our case, cement has been replaced partially with in varying proportions likewise from 0 to 20 and its effect has been analysed on the standard consistency, soundness, setting times of cement and compressive strength of cement mortar mixes. The cubes and cylinders of concrete were casted for variable content of dolomite powder. Pramod Dhamne | Dr. P. B. Nagarnaik ""Experimental Investigation on Replacement of Cement in Concrete Partially by using Dolamite Powder"" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-3 , April 2019, URL: https://www.ijtsrd.com/papers/ijtsrd23035.pdf
Paper URL: https://www.ijtsrd.com/engineering/civil-engineering/23035/experimental-investigation-on-replacement-of-cement-in-concrete-partially-by-using-dolamite-powder/pramod-dhamne
A LABORATORY STUDY OF CONCRETE MIX USING Ground Granulated Blast furnace Slagjay dalal
project on GGBS replace with CEMENT and check the strength of cement concrete and GGBS cement concrete on M20 grade. we also check price of cement concrete and GGBS cement concrete.
Study of Macro level Properties of SCC using GGBS and Lime stone powderIJERD Editor
One of the major environmental concerns is the disposal of the waste materials and utilization of
industrial by products. Lime stone quarries will produce millions of tons waste dust powder every year. Having
considerable high degree of fineness in comparision to cement this material may be utilized as a partial
replacement to cement. For this purpose an experiment is conducted to investigate the possibility of using lime
stone powder in the production of SCC with combined use GGBS and how it affects the fresh and mechanical
properties of SCC. First SCC is made by replacing cement with GGBS in percentages like 10, 20, 30, 40, 50 and
by taking the optimum mix with GGBS lime stone powder is blended to mix in percentages like 5, 10, 15, 20 as
a partial replacement to cement. Test results shows that the SCC mix with combination of 30% GGBS and 15%
limestone powder gives maximum compressive strength and fresh properties are also in the limits prescribed by
the EFNARC.
EXPERIMENTAL AND ANALYTICAL STUDY OF PARTIALLY REPLACED WASTE MATERIALS IN RI...guruvignesh N
This present study aims to identify the most suitable material
to utilize in concrete pavement. Several studies have been conducted across the worldwide to identify properties of waste materials on concrete and environmental also. From the basis of different studies the waste materials to be selected and replaced partial manner instead of concrete components. utilize waste material in rigid pavement for low cost concreting purpose. The selected appropriate ranging is to be used for rigid pavement construction in the grade of M30 as per IRC 44. Various engineering properties were obtained by strength and durability analysis.
Experimental Investigation on Replacement of Cement in Concrete Partially by ...ijtsrd
Concrete is the most extremely used construction material within the world, which always uses natural resources like lime, aggregates and water. The production of cement in world has increased greatly, due to this cement production emission of CO2 gas has been increased tremendously, ultimately environmental pollution increased to very large extent. This affect to environment has been reduced by cement has been replaced by some supplementary materials like Dolamite Powder or Fly ash or GGBS and so on. Dolamite. Powder was conducted detailed study and lots of research work has been made on other waste materials and it is found there is a great future scope for research on Dolamite Powder as a replacement to cement, sand or both. Now in our case, cement has been replaced partially with in varying proportions likewise from 0 to 20 and its effect has been analysed on the standard consistency, soundness, setting times of cement and compressive strength of cement mortar mixes. The cubes and cylinders of concrete were casted for variable content of dolomite powder. Pramod Dhamne | Dr. P. B. Nagarnaik ""Experimental Investigation on Replacement of Cement in Concrete Partially by using Dolamite Powder"" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-3 , April 2019, URL: https://www.ijtsrd.com/papers/ijtsrd23035.pdf
Paper URL: https://www.ijtsrd.com/engineering/civil-engineering/23035/experimental-investigation-on-replacement-of-cement-in-concrete-partially-by-using-dolamite-powder/pramod-dhamne
A LABORATORY STUDY OF CONCRETE MIX USING Ground Granulated Blast furnace Slagjay dalal
project on GGBS replace with CEMENT and check the strength of cement concrete and GGBS cement concrete on M20 grade. we also check price of cement concrete and GGBS cement concrete.
Experimental study on Use of Waste Glass as admixture in ConcreteIJSRD
Glass is utilized as a part of numerous structures in everyday life. It has restricted life and after use it is either stock heaped or sent to landfills. Since glass is non-biodegradable, landfills don't give a situation well-disposed arrangement. Thus, there is solid need to use waste glasses. Many efforts has already been made in concrete engineering as a partial replacement of cement or fine aggregate or coarse aggregate. In this experiment we use waste glass powder as a partial replacement of cement and a comparative study has been made with other admixture such as fly ash and silica fume. A series of test were conducted with partial replacement of glass by 15% and 30% to weight of cement where as we have used only 15% of partial replacement in case of fly ash and silica fume just to compare the results with glass at 15% and 30%. The present study demonstrates that waste glass, if ground finer than 100µm demonstrates a pozzolanic conduct. It responds with lime at early time phase of hydration forming extra CSH gel along these lines shaping denser bond matrix. The early utilization of alkalis by glass particles moderate alkali silica reaction consequently expands durability of cement.
An Experimental Study on Durability of Concrete Using Fly Ash & GGBS for M30 ...IJERD Editor
Concrete when subjected to severe environments its durability can significantly decline due to
degradation. Degradation of concrete structures by corrosion is a serious problem and has major economic
implications. In this study, an attempt has been made to study the durability of concrete using the mineral
admixtures like Fly Ash & Ground Granulated Blast Furnace Slag (GGBS) for M30 grade concrete.Cube
Specimens were casted and are immersed in normal water, sea water, H2SO4 of various concentrations and were
tested after 7 days, 28 days & 60 days.
EXPERIMENTAL BEHAVIOUR OF SELF COMPACTING CONCRETE USING GGBS WITH PARTIAL RE...Ijripublishers Ijri
Concrete is Most widely used construction Material in the Modern Era because of its good Compressive strength and
high durability. As we know Concrete comprises a Mixture of cement, sand (fine aggregate), course aggregate and water
which makes up normal plain concrete, to increase the strength of concrete we can design the mix with greater Flexibility,
but the problems Arises in structure as load age, increaseof floors which demands increase of high strength concrete
and more steel. So, especially at the beams, columns joints heavy reinforcement meshing is done so that it becomes If
the concrete is not compacted then strength may not be achieved, so the solution for the problem is SCC which we call
it asself-compacting concrete. Were this SCC has ability to compact by itself Gravity and self-flow ability same strength
can be Here in the research, it is carried out self-compaction concrete to improve strength & make concrete economical
so, a mix is dispend of M30,M40 Grades with adding chemical admixture named poly carboxylic ether (ADVA960) , a
Retarder Basically Which also increases strength and workability &replacing cement with GGBS (Ground Granulated
Blast Furnace Slag) 40%&50% .The tests are carried out to find the increase in strength by adding chemical admixture &
replacing GGBS 40% & 50%.By the chemical admixture adding up to 2% Max were previous strength shows that adding
of chemical admixture greater than 2% which results to increase the initial setting time and decrease in the w/c ratio.
Test will be conducted for 3,7,28 days find the increase of strength and its other properties
AN EXPERIMENTAL STUDY ON PROPERTIES OF TERNARY BLENDED CONCRETE USING GGBS AN...AM Publications
Ground granulated blast furnace slag (GGBS) is a by-product obtained from the blast furnaces used in the iron manufacturing industry. The disposal of the marble powder obtained from marble industry constitutes one of the environmental problems around the world. One of the possible solutions for the effective use of GGBS and marble powder is to partially replace cement in concrete. This paper presents the results of an experimental study on concrete in which the cement is partially replaced by both GGBS and marble powder. In this study, different percentages of GGBS and marble powder are used for partial replacement of cement by 30%. Tests conducted includes workability of fresh concrete (Slump test), strength of hardened concrete (Compressive strength, Split tensile strength and Flexural strength) and durability properties of concrete (Chloride resistance and Sulphate resistance).
Utilization of Foundry Waste Sand in the Preparation of Concreteiosrjce
IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) is a double blind peer reviewed International Journal that provides rapid publication (within a month) of articles in all areas of mechanical and civil engineering and its applications. The journal welcomes publications of high quality papers on theoretical developments and practical applications in mechanical and civil engineering. Original research papers, state-of-the-art reviews, and high quality technical notes are invited for publications.
based on the partial replacement of cement with ggbs as a concern to reduce the demand for cement. this seminar is being conducted in reference to 2 important journals...on the study carried out in RC beams and plain hardened concrete. Various tests are being conducted and it reveals that upto 70% replacement can be used which gives the same result as that without replacement.
Partial replacement of cement in concrete using waste glass powder and m sand...eSAT Journals
Abstract: The traditional Taguchi method is widely used for optimizing the process parameters of a single response problem. Optimization of a single response results the non-optimum values for remaining. But, the performance of a machining process is often evaluated by several quality responses. Under such circumstances, multi-characteristics response optimization may be the solution to optimize multi-responses simultaneously. In the present work, a multi-characteristics response optimization model based on Taguchi and Utility concept is used to optimize process parameters, such as magnetic flux, rotational speed of CFG rod, shape of CFG rod, number of cycles, abrasive-to-iron ratio and abrasive particle size on multiple performance characteristics, namely, surface roughness (Ra) and material removal (MR) during polishing of hollow cylindrical brass work-pieces with Centrifugal-Magnetic Force Assisted Abrasive Flow Machining (CMA2FM) Process. Taguchi’s L27 orthogonal array (OA) is selected for experimental planning. The ANOVA and F-tests are used to analyze the results. It is found that all the input parameters significantly improve the Utility function comprising of two quality characteristics (MR and %ΔRa). Further, the confirmation tests are conducted and the results are found to be within the confidence interval.
Keywords: Abrasive Flow Machining (AFM), Centrifugal Force, Magnetic Force, CFG Rod, CMA2FM, Utility Concept,TaguchiMethod,MultiResponseOptimization
Experimental Investigation on the Concrete as a Partial Replacement of Fine a...IJSRD
This project work involves in an experimental study on the concrete by using stone dust and brick dust on the mechanical properties of the concrete. In this experimental study two types admixtures are used in preparation of concrete mix. Stone dust and brick dust are added from 0% to 25% by weight of fine aggregate with increment of 5%. A comparative analysis has been carried out for conventional concrete to that of the admixture concrete in relation to their compressive, split tensile and flexural strength properties. As the stone dust and brick dust content increases in cement concrete, the compressive and split tensile values are proportionally increasing. It is observed that at 20% of stone dust and brick dust is the optimum dosages for concrete mixture.
Experimental study on Use of Waste Glass as admixture in ConcreteIJSRD
Glass is utilized as a part of numerous structures in everyday life. It has restricted life and after use it is either stock heaped or sent to landfills. Since glass is non-biodegradable, landfills don't give a situation well-disposed arrangement. Thus, there is solid need to use waste glasses. Many efforts has already been made in concrete engineering as a partial replacement of cement or fine aggregate or coarse aggregate. In this experiment we use waste glass powder as a partial replacement of cement and a comparative study has been made with other admixture such as fly ash and silica fume. A series of test were conducted with partial replacement of glass by 15% and 30% to weight of cement where as we have used only 15% of partial replacement in case of fly ash and silica fume just to compare the results with glass at 15% and 30%. The present study demonstrates that waste glass, if ground finer than 100µm demonstrates a pozzolanic conduct. It responds with lime at early time phase of hydration forming extra CSH gel along these lines shaping denser bond matrix. The early utilization of alkalis by glass particles moderate alkali silica reaction consequently expands durability of cement.
An Experimental Study on Durability of Concrete Using Fly Ash & GGBS for M30 ...IJERD Editor
Concrete when subjected to severe environments its durability can significantly decline due to
degradation. Degradation of concrete structures by corrosion is a serious problem and has major economic
implications. In this study, an attempt has been made to study the durability of concrete using the mineral
admixtures like Fly Ash & Ground Granulated Blast Furnace Slag (GGBS) for M30 grade concrete.Cube
Specimens were casted and are immersed in normal water, sea water, H2SO4 of various concentrations and were
tested after 7 days, 28 days & 60 days.
EXPERIMENTAL BEHAVIOUR OF SELF COMPACTING CONCRETE USING GGBS WITH PARTIAL RE...Ijripublishers Ijri
Concrete is Most widely used construction Material in the Modern Era because of its good Compressive strength and
high durability. As we know Concrete comprises a Mixture of cement, sand (fine aggregate), course aggregate and water
which makes up normal plain concrete, to increase the strength of concrete we can design the mix with greater Flexibility,
but the problems Arises in structure as load age, increaseof floors which demands increase of high strength concrete
and more steel. So, especially at the beams, columns joints heavy reinforcement meshing is done so that it becomes If
the concrete is not compacted then strength may not be achieved, so the solution for the problem is SCC which we call
it asself-compacting concrete. Were this SCC has ability to compact by itself Gravity and self-flow ability same strength
can be Here in the research, it is carried out self-compaction concrete to improve strength & make concrete economical
so, a mix is dispend of M30,M40 Grades with adding chemical admixture named poly carboxylic ether (ADVA960) , a
Retarder Basically Which also increases strength and workability &replacing cement with GGBS (Ground Granulated
Blast Furnace Slag) 40%&50% .The tests are carried out to find the increase in strength by adding chemical admixture &
replacing GGBS 40% & 50%.By the chemical admixture adding up to 2% Max were previous strength shows that adding
of chemical admixture greater than 2% which results to increase the initial setting time and decrease in the w/c ratio.
Test will be conducted for 3,7,28 days find the increase of strength and its other properties
AN EXPERIMENTAL STUDY ON PROPERTIES OF TERNARY BLENDED CONCRETE USING GGBS AN...AM Publications
Ground granulated blast furnace slag (GGBS) is a by-product obtained from the blast furnaces used in the iron manufacturing industry. The disposal of the marble powder obtained from marble industry constitutes one of the environmental problems around the world. One of the possible solutions for the effective use of GGBS and marble powder is to partially replace cement in concrete. This paper presents the results of an experimental study on concrete in which the cement is partially replaced by both GGBS and marble powder. In this study, different percentages of GGBS and marble powder are used for partial replacement of cement by 30%. Tests conducted includes workability of fresh concrete (Slump test), strength of hardened concrete (Compressive strength, Split tensile strength and Flexural strength) and durability properties of concrete (Chloride resistance and Sulphate resistance).
Utilization of Foundry Waste Sand in the Preparation of Concreteiosrjce
IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) is a double blind peer reviewed International Journal that provides rapid publication (within a month) of articles in all areas of mechanical and civil engineering and its applications. The journal welcomes publications of high quality papers on theoretical developments and practical applications in mechanical and civil engineering. Original research papers, state-of-the-art reviews, and high quality technical notes are invited for publications.
based on the partial replacement of cement with ggbs as a concern to reduce the demand for cement. this seminar is being conducted in reference to 2 important journals...on the study carried out in RC beams and plain hardened concrete. Various tests are being conducted and it reveals that upto 70% replacement can be used which gives the same result as that without replacement.
Partial replacement of cement in concrete using waste glass powder and m sand...eSAT Journals
Abstract: The traditional Taguchi method is widely used for optimizing the process parameters of a single response problem. Optimization of a single response results the non-optimum values for remaining. But, the performance of a machining process is often evaluated by several quality responses. Under such circumstances, multi-characteristics response optimization may be the solution to optimize multi-responses simultaneously. In the present work, a multi-characteristics response optimization model based on Taguchi and Utility concept is used to optimize process parameters, such as magnetic flux, rotational speed of CFG rod, shape of CFG rod, number of cycles, abrasive-to-iron ratio and abrasive particle size on multiple performance characteristics, namely, surface roughness (Ra) and material removal (MR) during polishing of hollow cylindrical brass work-pieces with Centrifugal-Magnetic Force Assisted Abrasive Flow Machining (CMA2FM) Process. Taguchi’s L27 orthogonal array (OA) is selected for experimental planning. The ANOVA and F-tests are used to analyze the results. It is found that all the input parameters significantly improve the Utility function comprising of two quality characteristics (MR and %ΔRa). Further, the confirmation tests are conducted and the results are found to be within the confidence interval.
Keywords: Abrasive Flow Machining (AFM), Centrifugal Force, Magnetic Force, CFG Rod, CMA2FM, Utility Concept,TaguchiMethod,MultiResponseOptimization
Experimental Investigation on the Concrete as a Partial Replacement of Fine a...IJSRD
This project work involves in an experimental study on the concrete by using stone dust and brick dust on the mechanical properties of the concrete. In this experimental study two types admixtures are used in preparation of concrete mix. Stone dust and brick dust are added from 0% to 25% by weight of fine aggregate with increment of 5%. A comparative analysis has been carried out for conventional concrete to that of the admixture concrete in relation to their compressive, split tensile and flexural strength properties. As the stone dust and brick dust content increases in cement concrete, the compressive and split tensile values are proportionally increasing. It is observed that at 20% of stone dust and brick dust is the optimum dosages for concrete mixture.
Concrete is world’s most used material after water
for urban development. Concrete is made up of naturally
occurring material such as Cement, Aggregate and Water.
The cement is major ingredient of concrete and due to rapid
production of cement, various environmental problems are
occurred i.e. Emission of green house gases such as CO2. The
production of Portland cement is energy intensive.
Global warming gas is released when the raw
material of cement, limestone and clay is crushed and heated
in a furnace at high temperature of about 1500’C. Each year
approximately 1.89 billion tons of cement has been produced
world wide.
An Experimental Study on Behavior of Partial Replacement of Cement with Groun...IJERA Editor
Concrete has occupied an important place in construction industry in the past few decades and it is used widely in all types of constructions ranging from small buildings to large infrastructural dams or reservoirs.GGBS is obtained from making of iron.It Is no use for other things.It pollutes the environmental such as land pollution, water pollution etc..when we use the GGBS in partial replacement of cement it increase the strengths of the cubes as well as decrease the pollution of the environmental.In my investigation GGBS used at 10%,20%,30%,40%,50% for M20 and M30 43 grades.It is gives increase strength values at 10%,20% and 30% compared to normal mixes.
Quality defects in TMT Bars, Possible causes and Potential Solutions.PrashantGoswami42
Maintaining high-quality standards in the production of TMT bars is crucial for ensuring structural integrity in construction. Addressing common defects through careful monitoring, standardized processes, and advanced technology can significantly improve the quality of TMT bars. Continuous training and adherence to quality control measures will also play a pivotal role in minimizing these defects.
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
Forklift Classes Overview by Intella PartsIntella Parts
Discover the different forklift classes and their specific applications. Learn how to choose the right forklift for your needs to ensure safety, efficiency, and compliance in your operations.
For more technical information, visit our website https://intellaparts.com
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
COLLEGE BUS MANAGEMENT SYSTEM PROJECT REPORT.pdfKamal Acharya
The College Bus Management system is completely developed by Visual Basic .NET Version. The application is connect with most secured database language MS SQL Server. The application is develop by using best combination of front-end and back-end languages. The application is totally design like flat user interface. This flat user interface is more attractive user interface in 2017. The application is gives more important to the system functionality. The application is to manage the student’s details, driver’s details, bus details, bus route details, bus fees details and more. The application has only one unit for admin. The admin can manage the entire application. The admin can login into the application by using username and password of the admin. The application is develop for big and small colleges. It is more user friendly for non-computer person. Even they can easily learn how to manage the application within hours. The application is more secure by the admin. The system will give an effective output for the VB.Net and SQL Server given as input to the system. The compiled java program given as input to the system, after scanning the program will generate different reports. The application generates the report for users. The admin can view and download the report of the data. The application deliver the excel format reports. Because, excel formatted reports is very easy to understand the income and expense of the college bus. This application is mainly develop for windows operating system users. In 2017, 73% of people enterprises are using windows operating system. So the application will easily install for all the windows operating system users. The application-developed size is very low. The application consumes very low space in disk. Therefore, the user can allocate very minimum local disk space for this application.
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
Event Management System Vb Net Project Report.pdfKamal Acharya
In present era, the scopes of information technology growing with a very fast .We do not see any are untouched from this industry. The scope of information technology has become wider includes: Business and industry. Household Business, Communication, Education, Entertainment, Science, Medicine, Engineering, Distance Learning, Weather Forecasting. Carrier Searching and so on.
My project named “Event Management System” is software that store and maintained all events coordinated in college. It also helpful to print related reports. My project will help to record the events coordinated by faculties with their Name, Event subject, date & details in an efficient & effective ways.
In my system we have to make a system by which a user can record all events coordinated by a particular faculty. In our proposed system some more featured are added which differs it from the existing system such as security.
Vaccine management system project report documentation..pdfKamal Acharya
The Division of Vaccine and Immunization is facing increasing difficulty monitoring vaccines and other commodities distribution once they have been distributed from the national stores. With the introduction of new vaccines, more challenges have been anticipated with this additions posing serious threat to the already over strained vaccine supply chain system in Kenya.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.