After studying this unit, you should be able to understand
introduction and working principle of milling machine,
different type of milling operations,
different type of milling machine and their main parts,
specifications of milling machines,different cutting parameters as setting of a milling machine,
introduction of milling cutters,
different operations that can be performed on a milling machine
A tool that has a single point for cutting purpose is called single point cutting tool. It is generally used in the lathe machine, shaper machine etc. It is used to remove the materials from the workpiece.
Press working terminology is described in a simple way to understand.Classification and Types are also explained in a simple way to understand by everyone.
Unit 2 Machinability, Cutting Fluids, Tool Life & Wear, Tool MaterialsMechbytes
Concept of machinability, machinability index, factors affecting machinability
Different mechanism of tool wear types of tool wear (crater, flank etc.), Measurement and control of tool wear
Concept of tool life, Taylor's tool life equation (including modified version)
Different tool materials and their applications including effect of tool coating
Introduction to economics of machining
Cutting fluids: types, properties, selection and application methods
After studying this unit, you should be able to understand
introduction and working principle of milling machine,
different type of milling operations,
different type of milling machine and their main parts,
specifications of milling machines,different cutting parameters as setting of a milling machine,
introduction of milling cutters,
different operations that can be performed on a milling machine
A tool that has a single point for cutting purpose is called single point cutting tool. It is generally used in the lathe machine, shaper machine etc. It is used to remove the materials from the workpiece.
Press working terminology is described in a simple way to understand.Classification and Types are also explained in a simple way to understand by everyone.
Unit 2 Machinability, Cutting Fluids, Tool Life & Wear, Tool MaterialsMechbytes
Concept of machinability, machinability index, factors affecting machinability
Different mechanism of tool wear types of tool wear (crater, flank etc.), Measurement and control of tool wear
Concept of tool life, Taylor's tool life equation (including modified version)
Different tool materials and their applications including effect of tool coating
Introduction to economics of machining
Cutting fluids: types, properties, selection and application methods
This presentation is about the Jigs and fixtures used for holding the components which have to be welded . It is normally used in automated welding systems . It is beneficial for high productivity and safety .
igs and fixtures are specialised tools used in manufacturing to secure workpi...yhchauhan
igs and fixtures are specialised tools used in manufacturing to secure workpieces and guide cutting or shaping tools, ensuring precision and repeatability in production processes.
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
CFD Simulation of By-pass Flow in a HRSG module by R&R Consult.pptxR&R Consult
CFD analysis is incredibly effective at solving mysteries and improving the performance of complex systems!
Here's a great example: At a large natural gas-fired power plant, where they use waste heat to generate steam and energy, they were puzzled that their boiler wasn't producing as much steam as expected.
R&R and Tetra Engineering Group Inc. were asked to solve the issue with reduced steam production.
An inspection had shown that a significant amount of hot flue gas was bypassing the boiler tubes, where the heat was supposed to be transferred.
R&R Consult conducted a CFD analysis, which revealed that 6.3% of the flue gas was bypassing the boiler tubes without transferring heat. The analysis also showed that the flue gas was instead being directed along the sides of the boiler and between the modules that were supposed to capture the heat. This was the cause of the reduced performance.
Based on our results, Tetra Engineering installed covering plates to reduce the bypass flow. This improved the boiler's performance and increased electricity production.
It is always satisfying when we can help solve complex challenges like this. Do your systems also need a check-up or optimization? Give us a call!
Work done in cooperation with James Malloy and David Moelling from Tetra Engineering.
More examples of our work https://www.r-r-consult.dk/en/cases-en/
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Explore the innovative world of trenchless pipe repair with our comprehensive guide, "The Benefits and Techniques of Trenchless Pipe Repair." This document delves into the modern methods of repairing underground pipes without the need for extensive excavation, highlighting the numerous advantages and the latest techniques used in the industry.
Learn about the cost savings, reduced environmental impact, and minimal disruption associated with trenchless technology. Discover detailed explanations of popular techniques such as pipe bursting, cured-in-place pipe (CIPP) lining, and directional drilling. Understand how these methods can be applied to various types of infrastructure, from residential plumbing to large-scale municipal systems.
Ideal for homeowners, contractors, engineers, and anyone interested in modern plumbing solutions, this guide provides valuable insights into why trenchless pipe repair is becoming the preferred choice for pipe rehabilitation. Stay informed about the latest advancements and best practices in the field.
1. MSME TOOL ROOM
INDO GERMAN TOOL ROOM
AHMEDABAD
SUBJECT: JIGS , FIXTURES & GAUGES
Page 1 of 21
Compiled by : T.BALAJI, Sr.Engineer.
1. Mass production of components using molds, Jigs & fixtures
Definitions
Tooling. Tooling is a general term used to encompass many different
processes involving the design and manufacture of special tools, dies,
molds, jigs, and fixtures. The most common type of tooling consists of
dies that are used to stamp or blank sheet metal parts for mass
production. The use of a stamping or blanking die makes it possible to
produce thousands of parts with consistent dimensional accuracy at a
rapid pace. This ensures that the die-produced parts will fit correctly into
their next assembly stage, such as in a complex mechanical device or
mechanism, and have interchangeability.
The production of detail parts from a tooling device such as a stamping
die reduces the overall cost of producing industrial and consumer
products in relation to the cost of the die versus the number of parts to
be made on the die. Complex tooling devices are relatively expensive to
produce and usually must be justified by the number of parts they
produce during a set time interval. As a general rule, thousands of parts
should be produced yearly to justify tooling costs and maintenance of
the tools.
Die making. One of the most common tooling procedures is the design
and production of dies, i.e., die making. Industry uses a great variety of
dies, including
Stamping, blanking, and punching dies
Bending and forming dies
Combination or progressive dies
Forging dies
Dies for die casting metals and metal alloys
Beading dies (a form of bending die)
Extrusion dies
Drawing dies...
2. MSME TOOL ROOM
INDO GERMAN TOOL ROOM
AHMEDABAD
SUBJECT: JIGS , FIXTURES & GAUGES
Page 2 of 21
Compiled by : T.BALAJI, Sr.Engineer.
The successful running of any mass production depends upon the
interchange ability to facilitate easy assembly and reduction of unit cost.
Mass production methods demand a fast and easy method of positioning
work for accurate operations on it.
Jigs and fixtures are production tools used to accurately manufacture
duplicate and interchangeable parts. Jigs and fixtures are specially
designed so that large numbers of components can be machined or
assembled identically, and to ensure interchange ability of components.
Location-
Location should ensure equal distribution of forces throughout all
sequence of operation.
Location should be hard resistant, wear resistant and high degree
of accuracy.
Movement of workpiece should be restricted.
Should be fool proofed to avoid improper locations of the
workpiece.
Should facilitate easy and quick loading of workpiece.
Redundant locators should be avoided.
Sharp corners must be avoided.
At least one datum surface should be establised.
Clamping arrangements-
Quick acting clamps must be used as far as possible. The clamping
should not cause any deformation to the workpiece It should always be
arranged directly above points supporting the work. Power driven
clamps are favoured as they are quick acting, controllable, reliable and
operated without causing any fatigue to the operators.
Features of clamps:
Clamping pressure should be low.
Should not cause distortion .
Simple and fool proof.
Movement of clamp should be minimum.
Case hardened to prevent wear.
Sufficiently robust to avoid bending.
3. MSME TOOL ROOM
INDO GERMAN TOOL ROOM
AHMEDABAD
SUBJECT: JIGS , FIXTURES & GAUGES
Page 3 of 21
Compiled by : T.BALAJI, Sr.Engineer.
2. BASICS OF JIGS & FIXTURES:
JIG.
It is a work holding device that holds, supports and locates the
workpiece and guides the cutting tool for a specific operation.
• A jig's primary purpose is to provide repeatability, accuracy, and
interchangeability in the manufacturing of products. A device that
does both functions (holding the work and guiding a tool) is called
a jig.
FIXTURE:
• It is a work holding device that holds, supports and locates the
workpiece for a specific operation but does not guide the cutting
tool. It provides only a reference surface or a device.
PURPOSE OF FIXTURE:
The main purpose of a fixture is to locate and in some cases hold a
workpiece during either a machining operation or some other industrial
process.
Fundamental principles of Jigs and Fixtures design
• LOCATING POINTS
• FOOL PROOF
• REDUCTION OF IDLE TIME
• WEIGHT OF JIGS AND FIXTURES
• JIGS PROVIDED WITH FEET
• MATERIALS FOR JIGS AND FIXTURES
• CLAMPING DEVICE
4. MSME TOOL ROOM
INDO GERMAN TOOL ROOM
AHMEDABAD
SUBJECT: JIGS , FIXTURES & GAUGES
Page 4 of 21
Compiled by : T.BALAJI, Sr.Engineer.
• LOCATING POINTS
Good facilities should be provided for locating the work. The article
to be machined must be easily inserted and quickly taken out from
the jig so that no time is wasted in placing the workpiece in
position to perform operations. The position of workpiece should
be accurate with respect to tool guiding in the jig or setting
elements in fixture.
• FOOL PROOF: The design of jigs and fixtures should be such
that it would not permit the workpiece or the tool to inserted in any
position other than the correct one.
• REDUCTION OF IDLE TIME:
Design of Jigs and Fixtures should be such that the process,
loading, clamping and unloading time of the workpiece takes
minimum as far as possible.
• WEIGHT OF JIGS AND FIXTURES: It should be easy to handle,
smaller in size and low cost in regard to amount of material used
without sacrificing rigidity and stiffness.
• JIGS PROVIDED WITH FEET: Jigs sometimes are provided with
feet so that it can be placed on the table of the machine.
• MATERIALS FOR JIGS AND FIXTURES: Usually made of
hardened materials to avoid frequent damage and to resist wear.
• Example- MS, Cast iron, Diesteel, CS, HSS.
5. MSME TOOL ROOM
INDO GERMAN TOOL ROOM
AHMEDABAD
SUBJECT: JIGS , FIXTURES & GAUGES
Page 5 of 21
Compiled by : T.BALAJI, Sr.Engineer.
CLAMPING DEVICE
• It should be as simple as possible without sacrificing effectiveness.
The strength of clamp should be such that not only to hold the
workpiece firmly in place but also to take the strain of the cutting
tool without springing when designing the jigs and fixtures.
Requirement of good clamping
• It should rigidly hold the workpiece.
• The workpiece being clamped should not be damaged due to
application of clamping pressure by the clamping unit.
• Clamping device should be capable to be unaffected by the
vibrations generated during an operation.
• Clamping pressure should be directed towards the support
surfaces or support points to prevent undesired lifting of workpiece
from its supports.
• Clamping faces should be hardened by proper treatments to
minimize their wearing out.
• To handle the workpieces made of fragile material the faces of
clamping unit should be equipped with fibre pads to avoid any
damage to workpiece
Types of clamp
• Heel clamp
• Bridge clamp
• Edge clamp
• Screw clamp
• Latch clamp
6. MSME TOOL ROOM
INDO GERMAN TOOL ROOM
AHMEDABAD
SUBJECT: JIGS , FIXTURES & GAUGES
Page 6 of 21
Compiled by : T.BALAJI, Sr.Engineer.
Types of jigs
• Drilling jig:
• Template jig
• Plate type jig
• Open type jig
• Box type jig
• Solid type jig
• Pot type jig
• Index jig
• Multi station jig
• Universal jig
Essential features of Jigs and Fixtures
Reduction of idle time – Should enable easy clamping and
unloading such that idle time is minimum.
Cleanliness of machining process – Design must be such that
not
much time is wasted in cleaning of scarfs, burrs, chips etc.
Replaceable part or standardization – The locating and
supporting
surfaces as far as possible should be replaceable, should be
standardized so that their interchangeable manufacture is possible.
Provision for coolant – Provision should be there so that the tool
is cooled and the swarfs and chips are washed away.
Hardened surfaces – All locating and supporting surfaces
should be hardened materials as far as conditions permit so
that they are not quickly worn out and accuracy is retained
for a long time.
7. MSME TOOL ROOM
INDO GERMAN TOOL ROOM
AHMEDABAD
SUBJECT: JIGS , FIXTURES & GAUGES
Page 7 of 21
Compiled by : T.BALAJI, Sr.Engineer.
Inserts and pads – Should always be riveted to those faces of
the clamps which will come in contact with finished surfaces
of the workpiece so that they are not spoilt.
Fool-proofing – Pins and other devices of simple nature
incorporated in such a position that they will always spoil the
placement of the component or hinder the fitting of the
cutting tool until the latter are in correct pos.
Initial location – Should be ensured that workpiece is not
located on more than 3 points in anyone plane test to avoid
rocking, spring loading should be done
Position of clamps – Clamping should occur directly above
the points supporting the workpiece to avoid distortion and
springing.
Clearance – Sufficient amount of clearance should be provided
around the work so that operator’s hands can easily enter the
body for placing the workpiece and any variations of work can be
accommodated
Ejecting devices – Proper ejecting devices should be incorporated
in the body to push the workpiece out after operation
Rigidity and stability – It should remain perfectly rigid and stable
during operation. Provision should be made for proper positioning
and rigidly holding the jigs and fixtures.
MEANING OF LOCATION
It is very important to understand the meaning of location before
understanding abut the jigs and fixtures. The location refers to the
establishment of a desired relationship between the workpiece and the
jigs or fixture correctness of location directly influences the accuracy of
the finished product. The jigs and fixtures are desired so that all
undesirable movements of the workpiece can be restricted.
Determination of the locating points and clamping of the workpiece serve
to restrict movements of the component in any direction, while setting it
in a particular pre-decided position relative to the jig. Before deciding the
locating points it is advisable to find out the all possible degrees of
freedom of the workpiece. Then some of the degrees of freedom or all of
them are restrained by making suitable arrangements. These
arrangements are called locators.
8. MSME TOOL ROOM
INDO GERMAN TOOL ROOM
AHMEDABAD
SUBJECT: JIGS , FIXTURES & GAUGES
Page 8 of 21
Compiled by : T.BALAJI, Sr.Engineer.
PRINCIPLES OF LOCATIONS
The principle of location is being discussed here with the help of a most
popular example which is available in any of the book covering jigs and
fixtures. It is important that one should understand the problem first.
Any rectangular body many have three axis along x-axis, y-axis and z-
axis. It can more along any of these axes or any of its movement can be
released to these three axes. At the same time the body can also rotate
about these axes too. So total degree of freedom of the body along
which it can move is six. For processing the body it is required to restrain
all the degree of freedom (DOF) by arranging suitable locating points
and then clamping it in a fixed and required position.
Six Points Location of a Rectangular Block
Considering the six degree of freedom of a rectangular block as shown
in Figure. It is made to rest on several points on the jig body. Provide a
rest to workpiece on three points on the bottom x-y surface. This will
stop the movement along z-axis, rotation with respect to x-axis and y-
axis. Supporting it on the three points is considered as better support
then one point or two points. Rest the workpiece on two points of side
surface (x-z), this will fix the movement of workpiece along y-axis and
rotation with respect to z-axis. Provide a support at one point of the
adjacent surface (y-z) that will fix other remaining free movements. This
principle of location of fixing points on the workpiece is also named as 3-
2-1 principle of fixture design as number of points selected at different
faces of the workpiece are 3, 2 and 1 respectively.
9. MSME TOOL ROOM
INDO GERMAN TOOL ROOM
AHMEDABAD
SUBJECT: JIGS , FIXTURES & GAUGES
Page 9 of 21
Compiled by : T.BALAJI, Sr.Engineer.
Location of a Cylinder on a Vee Block
The analysis of the principle of location of a cylinder on a Vee block is
indicated in Figure . All the degrees of freedom of the cylindrical object
are restrained. It is only fixed to move along axis AB. It can rotate about
the axis AB. These free movements are also indicated in the figure. If
the operation to be done on the cylindrical object requires restriction of
the above mentioned free movements also than some more locating
provisions must also be incorporated in addition to use of the Vee block.
10. MSME TOOL ROOM
INDO GERMAN TOOL ROOM
AHMEDABAD
SUBJECT: JIGS , FIXTURES & GAUGES
Page 10 of 21
Compiled by : T.BALAJI, Sr.Engineer.
DIFFERENT TYPES OF CLAMPS
Heel Clamp
The simple form of a heel clamp is shown in Figure . Rotation of the
clamp in clockwise direction is prevented and it is allowed in
anticlockwise direction. For releasing the workpiece the clamping nut is
unscrewed. The free movement in anticlockwise direction takes place
before un-securing the nut to release the workpiece.
Bridge Clamp
The bridge clamp is illustrated in Figure . It applies more clamping
pressure as compared to heel clamp. The clamping pressure
experienced by the workpiece depends on the distances „x‟ and „y‟
marked in the Figure . To release the workpiece the nut named as
clamping nut is unscrewed. The spring lifts the lever to release the
workpiece.
11. MSME TOOL ROOM
INDO GERMAN TOOL ROOM
AHMEDABAD
SUBJECT: JIGS , FIXTURES & GAUGES
Page 11 of 21
Compiled by : T.BALAJI, Sr.Engineer.
Edge Clamp or Side Clamp
A side clamp is also known as edge clamp. In this case the surface to be
machined is always clamped above the clamping device. This clamping
device is recommended for fixed length workpiece. The clamping device
is illustrated in Figure . Releasing and clamping of the workpiece can be
accomplished by unscrewing and screwing of the clamping nut
respectively.
Screw Clamp
The screw clamp is illustrated in Figure . It is also known as clamp
screw. This clamping apply pressure directly on the side faces of the
workpiece. There is a floating pad at their end to serve the following
purposes :
(a) It prevents displacement of workpiece and slip.
(b) It prevents denting of clamping area of workpiece.
(c) The available cushion prevents deflection of screw.
In addition to the above there are some disadvantages associated with
this method. The clamping pressure largely depends on the workpiece, it
varies from one workpiece to other. It is more time consuming and more
efforts are required.
12. MSME TOOL ROOM
INDO GERMAN TOOL ROOM
AHMEDABAD
SUBJECT: JIGS , FIXTURES & GAUGES
Page 12 of 21
Compiled by : T.BALAJI, Sr.Engineer.
Equalizing Clamps
Equalizing clamp is illustrated in Figure . It is recommended to apply
equal pressure on the two faces of the work. The pressure applied can
be varied by tightened or loosening the screw provided for the purpose.
13. MSME TOOL ROOM
INDO GERMAN TOOL ROOM
AHMEDABAD
SUBJECT: JIGS , FIXTURES & GAUGES
Page 13 of 21
Compiled by : T.BALAJI, Sr.Engineer.
FIXTURES
Fixtures are designed specifically for an operation and so these are
named on the base of the operation to be carried out with their help.
Fixtures are used to hold the workpiece properly to carryout the
operations.
Different types of fixtures are listed below.
(a) Turning fixtures
(b) Milling fixtures
(c) Fixture for grinding
(d) Fixture for broaching
(e) Fixture for boring/drilling
(f) Tapping fixture
(g) Fixture for welding
(h) Assembling fixture.
The following is a partial list of production operations that use fixtures:
Assembling Lapping
Boring Milling
Broaching Planning
Drilling Sawing
Forming Shaping
Gauging Stamping
Grinding Tapping
Heat treating Testing
Honing Turning
Inspecting Welding
14. MSME TOOL ROOM
INDO GERMAN TOOL ROOM
AHMEDABAD
SUBJECT: JIGS , FIXTURES & GAUGES
Page 14 of 21
Compiled by : T.BALAJI, Sr.Engineer.
MAJOR ELEMENTS OF JIGS & FIXTURES
arresting of block by using suitable fixture
15. MSME TOOL ROOM
INDO GERMAN TOOL ROOM
AHMEDABAD
SUBJECT: JIGS , FIXTURES & GAUGES
Page 15 of 21
Compiled by : T.BALAJI, Sr.Engineer.
Some basic principles or rules need to be followed while planning for locating blanks in
fixtures, such as;
One or more surfaces (preferably machined) and / or drilled / bored
hole(s) are to be taken for reference
The reference surfaces should be significant and important
feature(s) based on which most of the dimensions are laid
down.
Locating should be easy, quick and accurate.
In case of locating by pin, the pins and their mounting and
contact points should be strong, rigid and hard.
A minimum of three point must be used to locate a
horizontal flat surface.
The locating pins should be as far apart as feasible.
Vee block and cones should be used for self-locating solid
and hollow cylindrical jobs as typically shown in Fig.
Sight location is applicable to first – operation location of
blank with irregular surfaces produced by casting, forging
etc. as indicated in Fig. when the bracket is first located on
two edges to machine the bottom surface which will be used
for subsequent locating.
16. MSME TOOL ROOM
INDO GERMAN TOOL ROOM
AHMEDABAD
SUBJECT: JIGS , FIXTURES & GAUGES
Page 16 of 21
Compiled by : T.BALAJI, Sr.Engineer.
17. MSME TOOL ROOM
INDO GERMAN TOOL ROOM
AHMEDABAD
SUBJECT: JIGS , FIXTURES & GAUGES
Page 17 of 21
Compiled by : T.BALAJI, Sr.Engineer.
LOCATING ELEMENTS and method
Locating Methods:
Locating from a Flat Surface:
There are three primary methods of locating work from a flat
surface:
solid supports
adjustable supports,
equalizing supports.
Solid supports:
Easiest and cheapest.
Less accurate.
Used where machined surface acts as a locating point.
Adjustable supports:
Used where surfaces are uneven(casting,forging..)
Threaded style is the easiest and more economical.
Adjustable locators are normally used with one or more solid
locators to allow any adjustment needed to level the work.
18. MSME TOOL ROOM
INDO GERMAN TOOL ROOM
AHMEDABAD
SUBJECT: JIGS , FIXTURES & GAUGES
Page 18 of 21
Compiled by : T.BALAJI, Sr.Engineer.
Equalizing supports:
They provide equal support through two connected contact points.
As one point is depressed, the other raises and maintains contact
with the part.
This feature is especially necessary on uneven cast surfaces.
19. MSME TOOL ROOM
INDO GERMAN TOOL ROOM
AHMEDABAD
SUBJECT: JIGS , FIXTURES & GAUGES
Page 19 of 21
Compiled by : T.BALAJI, Sr.Engineer.
Locating Cylindrical Surfaces(Externally) “V”-locators
Vee locators are used mainly for round work.
They can locate flat work with rounded or angular ends and flat
discs.
Two types:Fixed and Adjustable.
Nesting locators :
position a part by enclosing it in a depression, or recess, of the same
shape as the part.
Nesting is the most accurate locating device for profile location.
Obviously, the height of the nest should be lesser than the height of
the workpiece.
In case of sheet-metals or thin workpieces, finger slots or ejector pins
should be provided.
20. MSME TOOL ROOM
INDO GERMAN TOOL ROOM
AHMEDABAD
SUBJECT: JIGS , FIXTURES & GAUGES
Page 20 of 21
Compiled by : T.BALAJI, Sr.Engineer.
Split contact locator
Relieved locator used in thick workpiece
Locator is relieved in the middle.
Only top and bottom areas come in contact with workpiece.
Dowel pin locator:
Most common type of fixed locator.
21. MSME TOOL ROOM
INDO GERMAN TOOL ROOM
AHMEDABAD
SUBJECT: JIGS , FIXTURES & GAUGES
Page 21 of 21
Compiled by : T.BALAJI, Sr.Engineer.
Standard parts:
jig button
Commonly made from case hardening steel
(16MnCr5 or 20MnCr5C15)
Have a hardness value of about 60 HRC
Have a case depth of 0.3 to 0.5 mm.
Jig bush:
Jig bushes locate and guide cutting tools.
Several types like linear,renewable,slip and screw bushes exist
Made from direct hardening type steel such as En31,T90,20MnV8
Hardness is usually 60 HRC with case hardened depth of 0.5 to .8mm