1. The document discusses the theory of metal cutting, including mechanics of chip formation, types of chips, cutting tool materials, tool wear, and other related topics.
2. It describes the different types of tool wear that can occur, including flank wear which results from the gradual wearing away of the cutting edge, and crater wear.
3. The key factors that influence chip formation and tool wear are also examined, such as material properties, cutting conditions, tool geometry, and choice of cutting tool material.
Fundamentals of Metal cutting and Machining Processes
MACHINING OPERATIONS AND MACHINING TOOLS
Turning and Related Operations
Drilling and Related Operations
Milling
Machining Centers and Turning Centers
Other Machining Operations
High Speed Machining
Sheet metal characteristics – shearing, bending and drawing operations – Stretch forming operations – Formability of sheet metal – Test methods –special forming processes-Working principle and applications – Hydro forming – Rubber pad forming – Metal spinning– Introduction of Explosive forming, magnetic pulse forming, peen forming, Super plastic forming – Micro forming.
Fundamentals of Metal cutting and Machining Processes
MACHINING OPERATIONS AND MACHINING TOOLS
Turning and Related Operations
Drilling and Related Operations
Milling
Machining Centers and Turning Centers
Other Machining Operations
High Speed Machining
Sheet metal characteristics – shearing, bending and drawing operations – Stretch forming operations – Formability of sheet metal – Test methods –special forming processes-Working principle and applications – Hydro forming – Rubber pad forming – Metal spinning– Introduction of Explosive forming, magnetic pulse forming, peen forming, Super plastic forming – Micro forming.
This presentation contains various aspects of metal cutting like mechanics of chip formation, single point cutting tool, chip breakers, types of chips,etc
Mechanics of chip formation, single point cutting tool, forces in machining, Types of chip, cutting tools– nomenclature, orthogonal metal cutting, thermal aspects, cutting tool materials, tool wear, tool life, surface finish, cutting fluids and Machinability.
IN THIS PRESENTATION CONSIST ON LATHE AND ITS TYPES EXPLAIN SHORT &
SWEET WITH GRAPHICAL REPRESENTATION
Note : PART-A CONTINUOUS..... Remaining Unit Update soon ...WIsh you Happy Learning.....
Broaching is a machining operation in which a tool having a series of cutting teeth called broach is either pulled or pushed by the broaching machine past the surface of a workpiece. when the operation is performed on internal surfaces is called internal broaching and in case of external surface external broaching.
After studying this unit, you should be able to understand
introduction and working principle of milling machine,
different type of milling operations,
different type of milling machine and their main parts,
specifications of milling machines,different cutting parameters as setting of a milling machine,
introduction of milling cutters,
different operations that can be performed on a milling machine
Mechanics of chip formation, single point cutting tool, forces in machining, Types of chip, cutting
tools– nomenclature, orthogonal metal cutting, thermal aspects, cutting tool materials, tool wear,
tool life, surface finish, cutting fluids and Machinability
This presentation contains various aspects of metal cutting like mechanics of chip formation, single point cutting tool, chip breakers, types of chips,etc
Mechanics of chip formation, single point cutting tool, forces in machining, Types of chip, cutting tools– nomenclature, orthogonal metal cutting, thermal aspects, cutting tool materials, tool wear, tool life, surface finish, cutting fluids and Machinability.
IN THIS PRESENTATION CONSIST ON LATHE AND ITS TYPES EXPLAIN SHORT &
SWEET WITH GRAPHICAL REPRESENTATION
Note : PART-A CONTINUOUS..... Remaining Unit Update soon ...WIsh you Happy Learning.....
Broaching is a machining operation in which a tool having a series of cutting teeth called broach is either pulled or pushed by the broaching machine past the surface of a workpiece. when the operation is performed on internal surfaces is called internal broaching and in case of external surface external broaching.
After studying this unit, you should be able to understand
introduction and working principle of milling machine,
different type of milling operations,
different type of milling machine and their main parts,
specifications of milling machines,different cutting parameters as setting of a milling machine,
introduction of milling cutters,
different operations that can be performed on a milling machine
Mechanics of chip formation, single point cutting tool, forces in machining, Types of chip, cutting
tools– nomenclature, orthogonal metal cutting, thermal aspects, cutting tool materials, tool wear,
tool life, surface finish, cutting fluids and Machinability
Theory of Metal cutting - Principles of Metal cutting, orthogonal and oblique cutting, Merchant circle diagram, cutting forces, power requirements, Economics of machining,problems
Production engineering, also known as manufacturing engineering, is the design, development, implementation, operation, maintenance, and control of all processes in the manufacture of a product. Within this context a 'product' is defined as an item that has value added to it during the production process.Production engineering, also known as manufacturing engineering, is the design, development, implementation, operation, maintenance, and control of all processes in the manufacture of a product. Within this context a 'product' is defined as an item that has value added to it during the production process.
This chapter aims to provide basic backgrounds of different types of machining processes and highlights on an understanding of important parameters which affects machining of metals with their chip removals.
Metal cutting or Machining is the process of producing workpiece by removing unwanted material from a block of metal. in the form of chips. This process is most important since almost all the products get their final shape and size by metal removal. either directly or indirectly.
The major drawback of the process is loss of material in the form of chips. In this chapter. we shall have a fundamental understanding of the basic metal process.
This slide is all about Metal cutting and Machining tools insights. It covers Mechanics of metal cutting, orthogonal and oblique machining, Tools geometry, Types of Chips, and Tools Signature.
Metrology Measurements and All units PPTdinesh babu
Metrology is the science of measurement, embracing both experimental and theoretical determinations at any level of uncertainty in any field of science and technology
TECHNICAL TRAINING MANUAL GENERAL FAMILIARIZATION COURSEDuvanRamosGarzon1
AIRCRAFT GENERAL
The Single Aisle is the most advanced family aircraft in service today, with fly-by-wire flight controls.
The A318, A319, A320 and A321 are twin-engine subsonic medium range aircraft.
The family offers a choice of engines
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
Quality defects in TMT Bars, Possible causes and Potential Solutions.PrashantGoswami42
Maintaining high-quality standards in the production of TMT bars is crucial for ensuring structural integrity in construction. Addressing common defects through careful monitoring, standardized processes, and advanced technology can significantly improve the quality of TMT bars. Continuous training and adherence to quality control measures will also play a pivotal role in minimizing these defects.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...Amil Baba Dawood bangali
Contact with Dawood Bhai Just call on +92322-6382012 and we'll help you. We'll solve all your problems within 12 to 24 hours and with 101% guarantee and with astrology systematic. If you want to take any personal or professional advice then also you can call us on +92322-6382012 , ONLINE LOVE PROBLEM & Other all types of Daily Life Problem's.Then CALL or WHATSAPP us on +92322-6382012 and Get all these problems solutions here by Amil Baba DAWOOD BANGALI
#vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore#blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #blackmagicforlove #blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #Amilbabainuk #amilbabainspain #amilbabaindubai #Amilbabainnorway #amilbabainkrachi #amilbabainlahore #amilbabaingujranwalan #amilbabainislamabad
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
Vaccine management system project report documentation..pdfKamal Acharya
The Division of Vaccine and Immunization is facing increasing difficulty monitoring vaccines and other commodities distribution once they have been distributed from the national stores. With the introduction of new vaccines, more challenges have been anticipated with this additions posing serious threat to the already over strained vaccine supply chain system in Kenya.
4. What is a Cutting Tool
• A cutting tool is any tool that is used to
remove metal from the work piece by means
of shear deformation.
• It is one of most important components in
machining process
• It must be made of a material harder than
the material which is to be cut, and the tool
must be able to withstand the heat
generated in the metal cutting process.
• Two basic types
– Single point
– Multiple point 4
11. Nomenclature of Single Point Lathe Tool
The most significant terms in the geometry of a
cutting tool angles are:
–Relief or clearance angle
» Side relief
» End relief
–Rake angle
» Back Rake angle
» Side Rake angle
–Cutting edge angle
» Side Cutting edge angle
» End Cutting edge angle
» Nose Radius
11
12. Cutting-Tool Terms
Rake angle:
– Ground on a tool to provide a smooth flow of the
chip over the tool so as to move it away from the
work piece
12
Back Rake angle
• Ground on the face of the tool
• Influences the angle at which
chip leaves the nose of the tool
• Generally 8 - 100
Side Rake angle
• Ground on the tool face away
from the cutting edge
• Influences the angle at which
the chip leaves the work piece
• A lathe tool has 140 side rake.
13. Side Rake
• Large as possible to allow
chips to escape
• Amount determined
– Type and grade of cutting tool
– Type of material being cut
– Feed per revolution
• Angle of keenness
– Formed by side rake and side
clearance
13
14. Back Rake
• Angle formed between top face of tool
and top of tool shank
– Positive
• Top face slopes downward
away from point
– Negative
• Top face slopes upward
away from point
– Neutral
14
15. Rake Angles
• Small to medium rake angles cause:
– high compression
– high tool forces
– high friction
– result = Thick—highly deformed—hot chips
16. Cutting-Tool Terms
16
Functions:
• Strengthens finishing
point of tool
• Improves surface
finish on work
• Should be twice
amount of feed per
revolution
• Too large – chatter; too
small – weakens point
Nose Radius:
• Rounded tip on the point of the tool
17. Tool Angle Application
• Factors to consider for tool angles
– The hardness of the metal
– Type of cutting operation
– Material and shape of the cutting tool
– The strength of the cutting edge
18. Cutting Tool Geometry
• Cutting tool is device with which a material could be cut to the desired size, shape or finish.
So a cutting tool must have at least a sharp edge. There are two types of cutting tool. The
tool having only one cutting edge is called single point cutting tools. For example shaper
tools, lathe tools, planer tools, etc. The tool having more than one cutting edge is called
multipoint cutting tools. For example drills, milling cutters, broaches, grinding wheel honing
tool etc.
• A single point cutting tool may be either right or left hand cut tool depending on the
direction of feed.
25/18
Primary Cutting Edge
Right hand cutting
tool
Left hand cutting
tool
19. Tool-in-hand Nomenclature
• The geometry of a cutting tool consists of the following elements: face or rake surface, flank,
cutting edges and the corner. Face or rake is the surface of the cutting tool along which the
chips flow out. Flank surfaces are those facing the work piece. There are two flank surfaces,
principal and auxiliary flank surfaces. Principal cutting edge performs the major portion of
cutting and is formed by the intersecting line of the face with the principal flank surface.
Auxiliary cutting edge (often called end cutting edge) is formed by the intersection of the rake
surface with the auxiliary flank surface. Corner or cutting point is the meeting point of the
principal cutting edge with the auxiliary cutting edge.
25/19
Auxiliary flank surface
Corner
Principal cutting edge
Rake or Face
Shank of tool
Tool axis
Principal flank surface
Auxiliary
cutting edge
20. Single Point Cutting Tool
25/20
Side clearance
angle (αx)
Nose radius (r)
Side cutting edge
angle (φs)
Back rake
angle (γy)
End
clearance
angle (αy)
End cutting edge
angle (φe)
Side rake angle (γx)
Note: All the rake and clearance
angles are measured in normal
direction
21. • Side Cutting Edge Angle (φs): The side cutting-edge angle (SCEA) is usually referred to as the lead angle. It
is the angle enclosed between the side cutting edge and the longitudinal direction of the tool. The value
of this angle varies between 0° and 90°, depending upon the machinability, rigidity, and, sometimes, the
shape of the workpiece. As this angle increases from 0° to 15°, the power consumption during cutting
decreases. However, there is a limit for increasing the SCEA, beyond which excessive vibrations take place
because of the large tool-workpiece interface. On the other hand, if the angle were taken as 0°, the full
cutting edge would start to cut the workpiece at once, causing an initial shock. Usually, the recommended
value for the lead angle should range between 15° and 30°.
25/21
22. • Auxiliary or End Cutting Edge Angle (φe): The end cutting-edge angle (ECEA) serves to
eliminate rubbing between the end cutting edge and the machined surface of the workpiece.
Although this angle takes values in the range of 5° to 30°, commonly recommended values
are 8° to 15°.
• Side Clearance Angle (αx) and End Clearance Angle (αy): Side and end clearance (relief)
angles serve to eliminate rubbing between the workpiece and the side and end flank,
respectively. Usually, the value of each of these angles ranges between 5° and 15°.
25/22
23. • Back Rake Angle (γy) and Side Rake Angle (γX): Back and side rake angles determine the direction of flow
of the chips onto the face of the tool. Rake angles can be positive, negative, or zero. It is the side rake angle
that has the dominant influence on cutting. Its value usually varies between 0° and 15°, whereas the back
rake angle is usually taken as 0°.
• Nose radius (r): Nose radius is favorable to long tool life and good surface finish. A sharp point on the end
of a tool is highly stressed, short lived and leaves a groove in the path of cut. There is an improvement in
surface finish and permissible cutting speed as nose radius is increased from zero value. Too large a nose
radius will induce chatter.
25/23
24. Designation of Cutting Tools
• By designation or nomenclature of a cutting
tool is meant the designation of the shape of
the cutting part of the tool. The following
systems to designate the cutting tool shape
which are widely used are:
– Tool in Hand System
– Machine Reference System or American Standard
Association (ASA) System
– Tool Reference System
• Orthogonal Rake System (ORS)
• Normal Rake System (NRS)
– Maximum Rake System (MRS)
25/24
25. Classification of Metal cutting Process
• Orthogonal cutting (2 Dimensional cutting)
• Oblique cutting (3 Dimensional cutting)
26. Orthogonal cutting
• The cutting edge of the
tool perpendicular to
the cutting velocity.
• This cutting involves
two forces only
27. Oblique cutting
• When the cutting edge
is inclined at an acute
angle with the normal
cutting velocity vector is
called oblique cutting.
• Its also called
3 –dimensional cutting
29. CHIP FORMATION
The type of chip formed mainly based on
• Mechanical properties of metal to be cut
• Depth of cut
• Tool angles in process
• Cutting speed
• Feed , type of cutting fluid
• Surface finish required
• Co-efficient of friction between tool and work piece
• Machining temperature in cutting region
30. TYPES OF CHIPS
• Continuous chips
• Dis-continuous Chips
• Continuous chips with built-up edge
31. continuous chips
• A long ribbon like chips are
produced in the cutting operation
• advantage
• This kind of chip formation results
good surface finish, tool life and less
power consumption.
• Dis-advantage
• The coil type of chip will affect the
surface of the machined part and
also the worker to work
continuously.
• The disposal of this kind of chip also
tough
32. Required conditions of
continuous chips formation
• Ductile material
• Smaller depth of cut
• High cutting speed
• Large rake angle
• Sharp cutting edge
• Proper cutting fluid
• Low friction b/w tool face and chip
33. Dis-continuous chips
• The rupture of tool on the
work piece will result the
discontinuous chip formation.
Advantage
• The disposal of chip from the
w/p is easier.
Dis-advantage
• Suitable only for selected work
materials
34. Required conditions of
Dis -continuous chips formation
• Suitable for brittle material
• Small rake angle
• High depth of cut
• Low cutting speed
• Excess cutting fluid
• Low feed
35. Continuous chip with built up edge
• .
• This is a chip to be avoided
and is caused by small
particles from the work piece
becoming welded to the tool
face under high pressure and
heat.
• The phenomenon results in a
poor finish and damage to the
tool. It can be minimized or
prevented by using light cuts
at higher speeds with an
appropriate cutting lubricant.
36. Reasons for this type of chips
• Low cutting speed
• Poor cutting fluid
• Small rake angle
• Large under cut thickness
• Strong adhesion between chips and tool face
37. CHIP BREAKER
During machining, long and
continuous chips formed at high
cutting speed.
It will affect the machining
process.
It will spoil the tool, workpiece
and machine.
The chips are hard, sharp, and
hot. It will be difficult to remove
the metal and also dangerous to
safety.
The chip breakers are used to
break the chips into small pieces
for easy removal, safety and to
prevent damaging the machine
and work.
The simplest form of chip
breaker is made by grinding a
groove on the tool face a few
millimeters behind the cutting
edge.
TYPES
1. Step type - A step is ground on the tool
face behind the cutting edge. This step will
break the chip.
2. Groove type – A groove on the tool face
behind the cutting edge will break the chip
3. Clamp type – A thin breaker is clamped or
screwed on the face of the tool
45. Merchant’s circle diagram
ASSUMPTIONS
• The tool has sharp
cutting edge,
• The chip formation will
be continuous type
• The chip may be
considered as a separate
body
• The cutting velocity
remains constant
52. SHEAR STRAIN
• The chip consist of series of plate
elements of thickness Δt.
• It’s displaced through a
distance Δs to each other.
• Therefore shear strain,
e = Δs / Δt
e = (K2 – 2k sin α + 1) / k cos α
54. Material selection Factors
• The various tool materials used to removed the metal from the
work piece.
• The tool should be harder than the material which is to be cut
The selection of cutting tool material will
depend on the factors
• Volume of production
• Tool design
• Type of machining process
• Physical and chemical properties of a work material
• Rigidity and conditions of machine
55. PROPERTIES OF CUTTING TOOL MATERIAL
• A cutting tool must have the following characteristics in order to
produce good quality and economical parts:
• Hardness — harness and strength of the cutting tool must be
maintained at elevated temperatures, also called hot hardness
• Toughness — toughness of cutting tools is needed so that
tools don’t chip or fracture, especially during interrupted cutting
operations.
• Wear Resistance — wear resistance means the attainment of
acceptable tool life before tools need to be replaced.
• Low friction - The co-efficient of friction between tool and
work piece must be low.
• Cost of the tool – The material should be economical in
production. And it should be easy to manufacture.
56. ADDITIONAL PROPERTIES - Required
• It should have high thermal conductivity
• Resistant to thermal shock
• Easy to manufacture
57. Classification of tool material
• Carbon tool steel
• High speed steel
• Cemented Carbides
• Ceramics
• Diamonds
58. Carbon Tool Steel
Composition
• Carbon – 0.8 – 1.3 %
• Silicon - 0.1 – 0.4 %
• Manganese – 0.1 – 0.4 %
Suitable for low cutting speeds and
below 200 0c appllication places
It has good hardness, strength and
toughness.
Its cheap
Easy to forge
Easy to harden
With this chromium and
molybdenum are added to increase
hardness
Tungsten is added for improving
wear resistance
60. High Speed steels (H.S.S)
• These metal cuts the metal effectively at high speeds.
• The speed is 2 to 3 times greater than the carbon tool steel
• These tool maintain the hardness up to 900’c
• Various alloying elements improve the hardness and wear
resistance.
• Those are tungsten , chromium, vanadium, cobalt and
molybdenum
• TYPES
18 – 4 -1 High speed steel
Molybdenum high speed steel
Cobalt High speed steel
62. Examples for High speed steel –
Milling cutter , Broaches, turning tools
63. Cemented Carbides
• .its a mix of tungsten powder and carbon at high temperature
Tungsten
powder
+ Carbon
at high temperature
=
Its also combined with 82 % tungsten Carbide , 10 % titanium ,
8 % Cobalt
It can with stand at 1000’c , can operate at high speed – 6
times greater than high speed steel ..
Used in the form of insert in the tool.
65. Ceramics
• It’s a mixture of aluminium oxide and boron
nitrate powder at 1700 ‘c
• This has good hard and compressive strength
• It’s a high brittle material. So can not be used for
shock load operations
• Its also has a mixture of 90% aluminium oxide
10 % chromium oxide, magnesium oxide and
nitrogen oxide
66. CHARACTERISTICS
• Good cutting speed
• Rigidity of tool and w/p
• Highly finished surface on cutting tool
• Use of effective chip removal and chip guards
68. Diamond
• It’s a hardest cutting tool
• Poly crystalline diamond is manufactured by sintering
under high pressure and temperature.
• It has low co-efficient of friction, high compressive
strength and wear resistance.
• Deformation is less in process
• These tools are produced good surface finished object
at high speed with good dimensional accuracy
• It’s a small and best suited for good surface finish tool
• Having high thermal conductivity
71. TOOL WEAR
• Tool wear is still a significant problem in
cutting.
• Typical types of tool wear include,
• - Flank wear
• - Crater wear
72. FLANK WEAR
• Tool wear resulting in
the gradual wearing
away of the cutting edge.
Flank wear is mostly
caused by abrasion, is
predictable, and is the
most desired form of
tool wear.
74. CRATER WEAR
• The chip coming out wills slide over the tool
face with some pressure, this causes wear in
the face is called face wear.
• The cavity formed on the tool surface is called
crater wear.
• Crater wear is commonly occurred while
machining a ductile material which produces
continuous chips
78. NOSE WEAR
• The tip of the tool having more contact with
work piece during the machining operation.
• Due to this type of wear, more heat will be
generated.
• More cutting force will act on the tool.
• Due to this abrasion force, a small portion of
metal comes out is called nose wear.
80. TOOL LIFE
• The tool life is an important factor in a cutting
tool performance since a considerable time is
lost whenever the tool is ground and reset.
• The length of time that a cutting tool can
function properly before it begins to fail.
• During this period, the tool serves effectively
and efficiently.
THE FOLLOWING SOME EXPRESSING TOOL LIFE:
Volume of metal removed per grind.
No. of work pieces machined per grind.
Time unit.
81. .
MRR = Feed Rate X Width of Cut X Depth of Cut.
Speeds, feeds and DOC influence many aspects of
machining performance:
• Tool life
• Surface finish
• Dimensional accuracy of the manufactured part
• Power required by the machine tool
82. FACTORS AFFECTING TOOL LIFE
• Cutting speed
• Feed
• Depth of cut
• Tool geometry
• Tool material
• Work material
• Cutting fluid
• Rigidity of work, tool and machine
83. 1.Cutting speed -(FACTORS AFFECTING TOOL LIFE)
• When cutting speed increases, the cutting
temperature will increases. So hardness of the
tool decreases.
• This lead to flank wear and crater wear in the
tool. Finally will fail in a short time period
• So the tool life depend on cutting speed.
84. Taylor tool life equation
• where n and C are constants, whose values
depend on cutting conditions, work and tool
material properties, and tool geometry.
85. Feed & Depth of cut -(FACTORS AFFECTING TOOL LIFE)
• The life of the cutting tool influenced by the amount
of metal removed by the tool per minute.
• Fine feed – having continuous metal removal by the
tool. This result wear in the tool face.
• Coarse or depth of cut feed – having thicker chip
removal of dis-continuous chips. But this also affect
the tool geometry and lead it to wear.
• So optimum feed only minimize this problem
regarding tool life
86. Formula
• For low carbon steel material and cemented carbide tool , the
following relation applied
• V – cutting speed
• F – feed
• t – depth of cut
• T – tool life
87. TOOL GEOMETRY -(FACTORS AFFECTING TOOL LIFE)
Name of
the Angle description Required angle
Rake angle
If the rake angle is more the heat
distribution come to low – so tool life is
reduced
- 5 to + 10 degree
for turning austenitic
steel by carbide tool
So we need a optimum rake angle
Relief angle
Relief angle related to friction between tool
and work piece
More relief angle – results weakens the tool
strength – this lead to tool failure 12 to 15 degree
So we need optimum relief angle
Cutting angle
Nose radius
This angle should be optimum for having
good surface finish.
Increasing nose radius improve the life of the
tool
30 to 25 degree
88. Tool material -(FACTORS AFFECTING TOOL LIFE)
• The physical and chemical properties of tool
material affect the life of the tool.
• Example:
• For the given cutting speed H.S.S tool is more
durable than carbon steel tool.
• But carbide tool having more life than H.S.S tool
89. Cutting fluid -(FACTORS AFFECTING TOOL LIFE)
• The cutting fluid plays major role in reducing friction between
tool and work piece and also reduce the heat produced in the
process.
• Like wise it increase the tool life
• The cutting fluid directly controls the amount of heat at the chip
tool interface is given by
• T = tool life
• θ = temperature of chip tool interface
• n = An index which depend on shape and material of the cutting tool
90. Work piece material
-(FACTORS AFFECTING TOOL LIFE)
• Tool life also depend on the microstructure of
the work piece material.
• Tool life will be more when machining soft
materials than hard material like cast iron and
alloy steel
91. Rigidity of work, tool and machine
- (FACTORS AFFECTING TOOL LIFE)
• A strongly supported tool on a rigid machine
will have more life than tool machining under
vibrating machine.
• Loose work piece will reduce the life of the
tool.
97. INTRODUCTION
• In the metal cutting process the heat is produced due
to plastic deformation of metal.
• This heat weakens the strength of the tool and also
work piece.
• Also the friction between tool and work piece affect
the life of the tool.
• These all are avoided by using of cutting fluid in the
machining process
98. FUNCTIONS OF CUTTING FLUID
To avoid thermal distortion –
The cutting fluid minimize the temperature produced
in the cutting zone and avoid the metallurgical changes
in the work piece.
To avoid friction –
The cutting fluid also act as a lubricant and it minimize
the friction between tool and work piece , so that we
increase tool life and surface finish
• It also carried away the chip from the machining
area.
• It prevents the corrosion of work and machine
99. PROPERTIES OF CUTTING FLUID
• should act as a lubricant
• Low viscosity
• High specific heat, high heat conductivity
• High film coefficient
• should be economical
• should be odorless
• non – corrosive
• high flash point
• high heat absorbing capacity
• should be stable in all conditions
• It should not get oxidized or decomposed when left in air
• Economical to use
100. TYPES OF CUTTING FLUIDS
• Depend on material and machining process
1. water based cutting fluids
2. Straight or heat oil based cutting fluids
101. 1. water based cutting fluids
• Water 80 % + remaining soft soap Or Mineral oil
Is called soluble oil
• These soap oil increase the adhering property
with the work piece and minimize heat and
temperature.
• Emulsifiers break oil into minute particles and keep
them separated in water
• These kind of oils reduce corrosion , heat , friction and
tool wear in the process.
• Its available in less cost
102. 2. Straight or heat oil based cutting fluids
• It’s a un-diluted or pure oil based fluids.
• Mostly it mixed with sulphur and chlorine.
• CLASSIFICATION
• Mineral oil
• Straight fatty oil
• Mixed oil
• Sulphurised oil
• Chlorinated oil
103. Mineral oil
• These are the different composition of hydro
carbons
• This oil used light machining operations.
• Example
• Petroleum, kerosene , paraffin and some high
viscous oils
• Used in ordinary operations in turret and
capstan lathe
104. Straight fatty oil
• These are straight exact oil
example :
• vegetable oil,
• fish oil , animal oil
• Olive oil
• Cotton seed oil
• Whale oil
• These are not stable in operation . They are
used in thread cutting operation
105. Mixed oil
• It’s the mixture of straight fatty and 75% mineral
oil
• So it has excellent properties like cooling, lubricating
in all operation
• And its very cheaper than fatty oil
Uses
• In heavy duty machining , thread milling , all
lathe works
106. Sulphurised oil
• This is one type chemical additive oil
• Sulphur 5 % + Lard oil (animal oil)
• It act as a good lubricant and coolant
• Used in heavy duty lathe work, gear cutting
and thread grinding
107. Chlorinated oil
• Its also a chemical additive oil
• Chlorine 3% + mineral oil
• If we add sulphur and chlorine with mineral oil
it give very good properties.
• So we can use it in all severe cutting
operations on strong and tough materials such
as stainless steels and nickel alloys.
108. FACTORS CONSIDERED FOR
SELECTION OF CUTTING FLUID
• Cutting speed
• Feed rate
• Depth of cut
• Tool and work piece material
• Velocity of cutting fluid
• Life of the cutting fluid
• Tool life to be expected
• Economical aspects
109. Methods Of Applying Cutting Fluids
♦ Drop by drop under gravity
♦ Flood under gravity
♦ Form of liquid jet
♦ Atomized form with compressed air
♦ Through centrifugal action
110. MACHINABILITY
The term machinability refers to the ease with which a
metal can be cut permitting the removal of the
material with a satisfactory finish at low cost.
It can be defined as follows:
Tool life before tool failure or resharpening.
Quality of the machined surface.
The power consumption per unit volume of materials
removed
111. VARIABLES AFFECTING
MACHINABILITY
WORK VARIABLES:
Chemical composition of work materials.
Microstructure composition of work materials.
Mechanical properties such as ductility, toughness,
brittleness.
Physical properties.
Method of production.
112. VARIABLES AFFECTING
MACHINABILITY
TOOL VARIABLES:
The geometry and tool materials.
Nature of engagement of tool with the work.
Rigidity of tool.
MACHINE VARIABLES:
Rigidity of the machine.
Power and accuracy of the machine tool.
114. EVALUATION OF MACHINABILITY
Tool life/grind.
Rate of metal removal/grind.
Cutting force and power consumption.
Surface finish.
Dimensional stability of the finished work.
Heat generated during cutting.
Ease of chip disposal.
Chip hardness
Shape & size of chips.
115. ADVANTAGES OF HIGH
MACHINABILITY
Good surface finish.
High cutting speed.
Less power consumption.
High metal removal rate.
Tool wear reduced.
Tool life increased.
116. MACHINEABILITY INDEX
It is a quantitative measure of machinability. It is used to compare the
machinability of different metals and acts as a quick and reliable checking
method.
Machinability index, I
= (cutting speed of material for 20 min tool life) / (cutting speed of free
cutting steel for 20 min tool life)
I = Vi / Vs
Some common materials is:
Low carbon steel - 55 – 60%
Stainless steel - 25%
Red brass - 180%
Aluminium alloy - 390 – 1500%
Magnesium alloy - 500 – 2000%