This document provides a tutorial on configuring MikroTik routers for various purposes such as proxy servers, bandwidth management, NAT, bridging, and graphing. It discusses how to access MikroTik via the console, Winbox, or web interface. It also covers how to set up basic configurations like naming interfaces, assigning IP addresses, enabling transparent proxy, creating NAT and bandwidth limiting rules. The tutorial demonstrates how MikroTik can be used as a transparent web proxy, bandwidth limiter, bridge, and for traffic monitoring with MRTG/graphing.
1. Setup router
//to create a name for network card
//to assign ip address to network card
//to create NAT rule
//to assign gateway
//to assign dns
//to create dhcp
2.Create login page(Hotspot)
How to link from Mikrotik to Radius server
1. Setup router
//to create a name for network card
//to assign ip address to network card
//to create NAT rule
//to assign gateway
//to assign dns
//to create dhcp
2.Create login page(Hotspot)
How to link from Mikrotik to Radius server
Konfigurasi Server Gateway dengan fitur PROXY, WEBSERVER dan DHCPWalid Umar
Panduan diatas dikhusukan untuk siswa dan guru TKJ yang hendak mempraktekkan tentang panduan untuk membangun sebuah server gateway dengan fitur proxy, webserver dan dhcp
With so many new line of products and features from MikroTik, choosing one might be bit confusing. This topic will cover how to choose the right devices for your network!
An Express Guide ~ Cacti for IT Infrastructure Monitoring & GraphingAbhishek Kumar
It's an Express Guide to "Setup of Cacti Server with purpose of IT Infrastructure Monitoring & Service Graphs" ~~~~~ its aimed at monitoring of various IT services and brilliant graphing of statistics
Webinar topic: Running BGP with Mikrotik
Presenter: Achmad Mardiansyah
In this webinar series, We are discussing Running BGP with Mikrotik
Please share your feedback or webinar ideas here: http://bit.ly/glcfeedback
Check our schedule for future events: https://www.glcnetworks.com/schedule/
Follow our social media for updates: Facebook, Instagram, YouTube Channel, and telegram
The recording is available on Youtube
https://youtu.be/jqlz7C_Otv8
How to manage internet clients of an ISP with PPPoE and MikroTik. For
centralized AAA (Authentication, Authorization and Accounting), freeRadius is used.
How to manage internet clients of an ISP with PPPoE and MikroTik. For
centralized AAA (Authentication, Authorization and Accounting), freeRadius is used.
This presentation was presented at MUM Indonesia at Bali in 2008. Discussed about how to put extra layer of security into your MikroTik Router using Port Knocking mechanism.
Konfigurasi Server Gateway dengan fitur PROXY, WEBSERVER dan DHCPWalid Umar
Panduan diatas dikhusukan untuk siswa dan guru TKJ yang hendak mempraktekkan tentang panduan untuk membangun sebuah server gateway dengan fitur proxy, webserver dan dhcp
With so many new line of products and features from MikroTik, choosing one might be bit confusing. This topic will cover how to choose the right devices for your network!
An Express Guide ~ Cacti for IT Infrastructure Monitoring & GraphingAbhishek Kumar
It's an Express Guide to "Setup of Cacti Server with purpose of IT Infrastructure Monitoring & Service Graphs" ~~~~~ its aimed at monitoring of various IT services and brilliant graphing of statistics
Webinar topic: Running BGP with Mikrotik
Presenter: Achmad Mardiansyah
In this webinar series, We are discussing Running BGP with Mikrotik
Please share your feedback or webinar ideas here: http://bit.ly/glcfeedback
Check our schedule for future events: https://www.glcnetworks.com/schedule/
Follow our social media for updates: Facebook, Instagram, YouTube Channel, and telegram
The recording is available on Youtube
https://youtu.be/jqlz7C_Otv8
How to manage internet clients of an ISP with PPPoE and MikroTik. For
centralized AAA (Authentication, Authorization and Accounting), freeRadius is used.
How to manage internet clients of an ISP with PPPoE and MikroTik. For
centralized AAA (Authentication, Authorization and Accounting), freeRadius is used.
This presentation was presented at MUM Indonesia at Bali in 2008. Discussed about how to put extra layer of security into your MikroTik Router using Port Knocking mechanism.
Final ProjectFinal Project Details Description Given a spec.docxAKHIL969626
Final Project
Final Project Details:
Description: Given a specific scenario, create an appropriate IP addressing scheme, document a given network by creating a logical network diagram and create the appropriate access lists for use on the routers. Deliverables:
· Demonstrate the theory and practice of Cisco networking, routing, and switching strategies as outlined in the Cisco CCENT Certification exam
Prior to implementing any design we need to first write-up our proposed network design on paper. With that in mind, we begin by performing a network discovery. Once we have identified all the network devices and the needs of the organization, we can document the TCP/IP information that is needed for our design. In this exercise you will determine the subnet information for each department and assign IP addresses for the network devices.
You have been assigned as a networking tech for a new client, AAA Fabricating. The network is configured with a Class C network and the current allocation of IP addresses has been depleted. You have been tasked to reconfigure the network with a Class B address and assign a subnet to each of the 10 departments and the three routers.
Your network audit consists of the following information:
AAA Fabrication consists of 10 departments spread across three buildings.
Each building is connected using three Cisco 2800 Series routers. The three routers are located in the MIS wiring closet in Building 2.
Each department has its own Cisco 2950 switch.
There are at least two workstations in each department.
The company plans to use a class B address range starting at 172.16.0.0.
Each department must be assigned a subnet. Subnets should be designed to allow for the maximum number of hosts on each department subnet using classful subnetting.
The company also wants the three routers to communicate on the minimum quantity of IP addresses using three subnets.
Building 1
Subnet
Department
Subnet ID
Host ID Range
Broadcast Address
0
Warehouse
1
Receiving
2
shipping
3
Maintenance
Building 2
Subnet
Department
Subnet ID
Host ID Range
Broadcast Address
4
Accounting
5
Human Resources
6
Payroll
7
MIS
8
Employee Training
Building 3
Subnet
Department
Subnet ID
Host ID Range
Broadcast Address
9
R&D
10
Marketing
Routers
Building 1
Ethernet and Serial Interfaces
IP Address
Subnet Mask
Router
Fast Ethernet 0/0
Building 1
Serial 0/0
To Building 2
Serial 0/1
To Building 3
Building 2
Ethernet and Serial Interfaces
IP Address
Subnet Mask
Router
Fast Ethernet 0/0
Building 2
Serial 0/0
To Building 1
Serial 0/1
To building 3
Building 3
Ethernet and Serial Interfaces
IP Address
Subnet Mask
Router
Fast Ethernet 0/0
Building 3
Serial 0/0
To Building 1
Serial 0/1
To Building 2
Part 2
Create a logical Network Diagram
Logical Network topology represents a high level overview of the signal topology of the network. Every LAN has two different topologies, or the way that the devices on a networ ...
How to Use GSM/3G/4G in Embedded Linux SystemsToradex
The number of embedded devices that are connected to the internet is growing each day. Nowadays, they are installed majorly using a wireless connection. They need mobile network coverage to be connected to the internet. Read our next blog which tells you about the various configurations to connect a device such as Colibri iMX6S with the Colibri Evaluation Board running Linux to the internet through the PPP (Point-to-Point Protocol) link. Read More: https://www.toradex.com/blog/how-to-use-gsm-3g-4g-in-embedded-linux-systems
By the end of this chapter, you will be able to:
1) Explain how the functions of the application layer, session layer, and presentation layer work together to provide network services to end user applications.
2) Describe how common application layer protocols interact with end user applications.
3) Describe, at a high level, common application layer protocols that provide Internet services to end-users, including WWW services and email.
4) Describe application layer protocols that provide IP addressing services, including DNS and DHCP.
5) Describe the features and operation of well-known application layer protocols that allow for file sharing services, including: FTP, 6) File Sharing Services, SMB protocol.
7) Explain how data is moved across the network, from opening an application to receiving data.
Chapter 10: Objectives
--------------------------------------------------
By the end of this chapter, you will be able to:
Explain how the functions of the application layer, session layer, and presentation layer work together to provide network services to end user applications.
Describe how common application layer protocols interact with end user applications.
Describe, at a high level, common application layer protocols that provide Internet services to end-users, including WWW services and email.
Describe application layer protocols that provide IP addressing services, including DNS and DHCP.
Describe the features and operation of well-known application layer protocols that allow for file sharing services, including: FTP, File Sharing Services, SMB protocol.
Explain how data is moved across the network, from opening an application to receiving data.
Yaser Rahmati | یاسر رحمتی
Rahmati Academy | آکادمی رحمتی
www.yaser-rahmati.ir
www.rahmati-academy.ir
1. TUTORIAL MIKROTIK STEP BY STEP
By: Anung Muhandanu
MikroTik Overview
Mikrotik now widely used by ISPs, hotspot providers, or by the owner of the
cafe. Mikrotik OS router makes the computer into a reliable network that is equipped
with various features and tools, for both wired and wireless.
In this tutorial the author presents a discussion and a simple and simple
instructions on configuring the proxy for certain purposes and the public is typically
collected in server / router cafe as well as other tissues, such configuration for
example, for server NAT, Bridging, BW management, and MRTG.
Mikrotik version I use for this tutorial is MikroTik RouterOS 2.9.27
Access MikroTik:
1. via console
Mikrotik router board or PC can be accessed directly via the console / shell
and remote access using putty (www.putty.nl)
2. via Winbox
Mikrotik can also be accessed / remotely using software tools Winbox
3. via web
Mikrotik can also be accessed via web / port 80 by using a browser
• Naming MikroTik
[ropix@IATG-SOLO] > system identity print
name: "Mikrotik"
[ropix@IATG-SOLO] > system identity edit
value-name: name
Enter the editor type for example I change the name IATG-SOLO:
IATG-SOLO
C-c quit C-o save&quit C-u undo C-k cut line C-y paste
Edit and then press Clrl-O to save and exit the editor
1
2. If using Winbox, it looks like this:
• Changing the name of the interface:
[ropix@IATG-SOLO] > /interface print
Flags: X - disabled, D - dynamic, R - running
# NAME TYPE RX-RATE TX-RATE MTU
0 R ether1 ether 0 0 1500
1 R ether2 ether 0 0 1500
[ropix@IATG-SOLO] > /interface edit 0
value-name: name
The value 0 is the value ether1, if you want to replace ethet2 value 0 replaced by 1.
Entrance to the editor, for example I replace it with name local:
local
C-c quit C-o save&quit C-u undo C-k cut line C-y paste
Edit and then press Cltr-o to save and exit the editor, Do the same for interfaces ether
2, so that if seen again will appear like this:
[ropix@IATG-SOLO] > /interface print
Flags: X - disabled, D - dynamic, R - running
# NAME TYPE RX-RATE TX-RATE MTU
0 R local ether 0 0 1500
1 R public ether 0 0 1500
2
3. Via Winbox:
Select the menu interface, click the name of the interface that wants to be edited, so it
appears the edit window interface.
• Setting IP Address:
[ropix@IATG-SOLO] > /ip address add
address: 192.168.1.1/24
interface: local
[ropix@IATG-SOLO] > /ip address print
Flags: X - disabled, I - invalid, D - dynamic
# ADDRESS NETWORK BROADCAST INTERFACE
0 192.168.0.254/24 192.168.0.0 192.168.0.255 local
Enter the IP address value in the column address and netmask, enter the name of the
interface that wants to be given an IP address. For public interface Interface 2,
namely, the same way as above, so that if seen again will be 2
interfaces:[ropix@IATG-SOLO] > /ip address print
Flags: X - disabled, I - invalid, D - dynamic
# ADDRESS NETWORK BROADCAST INTERFACE
0 192.168.0.254/24 192.168.0.0 192.168.0.255 local
1 202.51.192.42/29 202.51.192.40 202.51.192.47 public
3
4. Via Winbox:
• Make Mikrotik NAT
Network Address Translation or more commonly referred to as NAT is a method to
connect more than one computer to the Internet network using a single IP address.
Number of use of this method due to limited availability of IP addresses, the need for
security , and the ease and flexibility in network administration.
Currently, the widely used IP protocol is IP version 4 (IPv4). With a length of the
address 4 bytes means that there are 2 to the power 32 = 4,294,967,296 IP addresses
available. This amount is theoretically the number of computers that can directly
connect to the internet. Because of this limitation most of the ISPs (Internet Service
Provider) will only allocate one address for one user and this address is dynamic,
meaning that a given IP address will be different every time the user connects to the
Internet. This will make it difficult for businesses to lower middle class. On the one
hand they need more computers are connected to the Internet, but on the other hand
only one IP address which means there is only one computer that can connect to the
internet. This can be overcome by using NAT. By NAT gateways that run on one
computer, one IP address can be shared with several other computer and they can
connect to the internet simultaneously.
Suppose we want to hide the local network / LAN 192.168.0.0/24 202.51.192.42
behind one IP address provided by ISP, which we use is a feature of Mikrotik source
network address translation (masquerading). Masquerading changes the data packets
from the IP address and port from the network 192.168.0.0/24 to 202.51.192.42
henceforth be forwarded to the global Internet network.
4
5. To use masquerading, source NAT rule with action 'masquerade' should be added to
the firewall configuration:
[ropix@IATG-SOLO] > /ip firewall nat add chain=srcnat
action=masquerade out-interface=public
If using Winbox, will look like this:
• As a transparent web proxy mikrotik
One function is to store the proxy cache. If a LAN uses a proxy to connect to the
Internet, it is done by the browser when a user accesses a web server URL is to take
these requests on a proxy server. Whereas if the data is not contained in the proxy
server then proxies to pick up directly from the web server. Then the request is stored
5
6. in the cache proxy. Furthermore, if there are clients who make requests to the same
URL , it will be taken from the cache. This will make access to the Internet faster.
How to ensure that each user accessing the Internet through a web proxy that we have
enabled? To this we can apply the transparent proxy. With transparent proxy, every
browser on computers that use this gateway automatically goes through a proxy.
Enabling web proxy in mikrotik fiture:
[ropix@IATG-SOLO] > /ip proxy set enabled=yes
[ropix@IATG-SOLO] > /ip web-proxy set
cache-administrator= ropix.fauzi@infoasia.net
[ropix@IATG-SOLO] > /ip web-proxy print
enabled: yes
src-address: 0.0.0.0
port: 3128
hostname: "IATG-SOLO"
transparent-proxy: yes
parent-proxy: 0.0.0.0:0
cache-administrator: "ropix.fauzi@infoasia.net"
max-object-size: 8192KiB
cache-drive: system
max-cache-size: unlimited
max-ram-cache-size: unlimited
status: running
reserved-for-cache: 4733952KiB
reserved-for-ram-cache: 2048KiB
Make a rule for transparent proxy on the firewall NAT, precisely there masquerading
under the rule for NAT:
[ropix@IATG-SOLO] > /ip firewall nat add chain=dstnat in-
interface=local src-address=192.168.0.0/24 protocol=tcp dst-port=80
action=redirect to-ports=3128
[ropix@IATG-SOLO] > /ip firewall nat print
Flags: X - disabled, I - invalid, D - dynamic
0 chain=srcnat out-interface=public action=masquerade
1 chain=dstnat in-interface=local src-address=192.168.0.0/24
protocol=tcp dst-port=80 action=redirect to-ports=3128
In Winbox:
1. Enable web proxy on the menu IP> Proxy> Access> Settings (check box enabled)
6
8. 3. Make a rule for transparent proxy on the menu IP> Firewall> NAT
• Transparent proxy with proxy servers separate / independent
MikroTik Web Proxy built in according to my observations not so good compared to
the squid proxy in Linux, squid in Linux has more flexibility to be modified and
diconfigure, eg for delay-pool feature and ACL lists that include files, not in the proxy
series 2.9.x.
Usually most people prefer to create their own proxy servers, with PC Linux /
FreeBSD and live directing all clients to the PC.
Topology PC proxy can be in a local network or using public ip.
Configuration almost similar to the transparent proxy, the difference is in the action
NAT rule is as follows:
8
9. In the above example 192.168.0.100 is the IP proxy server port 8080
• Mikrotik as a bandwidth limiter
Mikrotik can also be used for bandwidth limiter (queue). To control the data rate
allocation mechanism.
In general there are 2 types of bandwidth management at the proxy, the simple queue
and queue trees. Please use one only.
The next tutorial mikrotik all settings using Winbox, because it is more user friendly
and efficient.
Simple queue:
For example we will limit the bandwidth of the client with ip 192.168.0.3 that is for
upstream and downstream 128kbps 64kbps
Settings on the menu Queues> Simple Queues
Queue tree
Click the ip> firewall> magle
9
10. Make a rule (click the + red) with the following parameters:
On the General tab:
Chain = forward,
Src.address = 192.168.0.3 (or ip who want the limit)
On the Action tab:
Action = mark-connection,
New connection-mark = client3 con (or the name of the mark we created a
distinguished conection)
Click Apply and OK
10
11. Create another rule with the following parameters:
On the General tab: chain = forward,
Connection mark = client3-con (choose from dropdown menu)
On the Action tab:
Action = mark-packet,
New pcket Mark = client3 (or the name of the packet we created a distinguished
mark)
Click Apply and OK
Click the Queues> Queues Tree
11
12. Make a rule (click the + red) with the following parameters:
On the General tab:
Name = client3-in (eg),
Parent = public (which is the direction of outgoing interface),
Mark = client3 Package (choose from the dropdown, just that we make to magle)
Queue Type = default,
Priority = 8,
Max limit = 64k (for setting the bandwidth max download)
Click aplly and Ok
12
13. Create another rule with the following parameters:
On the General tab:
Name = client3-up (eg),
Parent = local (as an interface into which direction),
Mark = client3 Package (choose from the dropdown, just that we make to magle)
Queue Type = default,
Priority = 8,
Max limit = 64k (for setting max upload bandwidth)
Click aplly and Ok
Mikrotik as Bridging
Bridge is a way to connect two separate network segments together in a protocol
itself. Packages that are forwarded based on Ethernet addresses, not IP addresses
(such as routers). Because the packet forwarding done at Layer 2, all protocols can be
via a bridge.
So the analogy is like this, you have a local network 192.168.0.0/24 gateway to an
ADSL modem which also as a router with a local ip 192.168.0.254 and public ip
222.124.21.26.
You want to create a proxy server and proxy as a BW management for all clients.
Well want to put the location for the PC mikrotik? Among the hub / switch and
gateway / modem? Do not be like him as a NAT and we have to add 1 block io
private again different from the gateway modem?
The solution set as a bridging proxy, so seolah2 he only bridge between UTP cable
only. Topology as follows:
Internet----------Moderm/router-----------Mikrotik--------Switch/Hub-----Client
Setting bridging using Winbox
1. Add a bridge interface
Click the Interface menu and then click the + sign to add a red color interface, select
the Bridge
13
14. to name bridge interface, eg, we named bridge1
2. adding ether interface on the local and public interface
Click the IP> Bridge> Ports, then click the + sign to add a new rule:
Make 2 rules, to local and public interface.
3. Giving IP address to bridge interface
Click the IP menu and then click the + sign to add an interface IP, eg 192.168.0.100,
select bridge1 interface (or the name of the bridge interface that we created earlier)
14
15. By giving the IP address on bridge interface, the proxy can be either remote from the
network which is connected to a local interface or the public.
Mikrotik as MRTG / Graphing
Graphing is a tool in mokrotik enabled to monitor changes in the parameters at any
time. Changes that change the form of graphs uptodate and can be accessed using a
browser.
Graphing can display the information in the form:
* Resource usage (CPU, Memory and Disk usage)
* Traffic passing through the interfaces
* Traffic through simple queues
Activating the function grapping
Click the Tools menu> Graphing> Resource Rules
Is to enable graphing for Mikrotik resource usage. While allow address is anywhere
IP that can access these charts, 0.0.0.0 / 0 for all ip address.
Click the Tools menu> Graphing> Interface Rules
Is to enable graphing for monitoring traffic passing through the interface, please
select which interface you want monitored, or select "all" for all.
15
16. Graphing consists of two parts, first to collect information / data that both show in a
web format. To access the graphics, type the URL with the format http://
[Router_IP_address] / graphs / and choose from the menus there, where you want to
display graphics.
Sample results graph for traffic public interface:
Similarly, the authors convey a little tutorial for just sharing the knowledge or
simplify for easy understanding of the tutorials that are already available on the
official site mikrotik.
Warmest Regards,
Anung Muhandanu
16