To satisfy the ever-increasing demand for accuracy, the parts have to be produced with a less dimensional variation.
Hence, the labour and machinery required to manufacture a part has become more expensive.
It is essential for the manufacturer to have an in-depth knowledge of the tolerances to manufacture parts economically but, at the same time, adhere to quality and reliability aspects.
chapter-5 Limits, classification Fits and Tolerances.SHITALUDAGAVE2
It is impossible to produce a part to an exact size or basic size, some
variations, known as tolerances, need to be allowed.
The permissible level of tolerance depends on the functional requirements, which cannot be compromised
chapter-5 Limits, classification Fits and Tolerances.SHITALUDAGAVE2
It is impossible to produce a part to an exact size or basic size, some
variations, known as tolerances, need to be allowed.
The permissible level of tolerance depends on the functional requirements, which cannot be compromised
The limit fit tolerance refers to the acceptable degree of variation allowed in a part's dimensions or the permissible difference between the minimum and maximum sizes of mating parts in engineering and manufacturing. This system ensures that parts fit together properly while accounting for unavoidable variations in the manufacturing process.
The tolerance consists of two main components:
Limits: These are the extreme values (upper and lower bounds) within which the actual dimension of a part must fall.
Fits: The relationship between the parts based on the prescribed tolerance. Fits can be categorized into various types, such as clearance fit, interference fit, and transition fit, based on the allowances for the difference between the mating parts.
The ANSI (American National Standards Institute) and ISO (International Organization for Standardization) often provide standard charts and tables that detail various limit fit tolerance classes. These classes specify the allowances for different fits to ensure proper functionality while allowing for ease of assembly or providing a snug fit, depending on the application.
Selecting the appropriate limit fit tolerance depends on the specific requirements of the application, considering factors like function, material, environmental conditions, and manufacturing capabilities. This ensures that parts fit together with the required precision, avoiding issues like parts being too loose or too tight.
When specifying a limit fit tolerance for manufacturing or engineering purposes, it's essential to consider:
Design requirements: What function does the part need to fulfill?
Material properties: Different materials expand, contract, or behave differently under varying conditions.
Environmental factors: Temperature, humidity, and other external conditions may affect the parts' dimensions.
Manufacturing processes: The methods used for manufacturing can influence the achievable tolerance.
Ultimately, the right limit fit tolerance is a balance between functionality, ease of assembly, and ensuring the required performance of the final product. Engineering standards, charts, and tables provided by organizations like ANSI and ISO offer guidance in selecting appropriate tolerances for specific applications.
Basic concept of fits and tolerances and their practical use in fitment of anti friction bearings and couplings
Machine design and maintenance engineers do encounter the problem in deciding right kind of fitment while assembling various machine elements. Satisfactory functioning of a machine is very much dependent on use of right type of fitment between its various machine elements ( parts). Below is link to a presentation wherein I have tried to summarize the basic concepts of fits and tolerances and their practical use in fitment of rolling contact bearings and coupling
Similar to System of Limits, Fits, Tolerance and Gauging (20)
Inspection is the most common method of attaining standardization, uniformity and quality of workmanship. It is the cost art of controlling the product quality after comparison with the established standards and specifications. It is the function of quality control. An inspection is an indispensable tool of the modern manufacturing process. It helps to control quality, reduces manufacturing costs, eliminates scrap losses and assignable causes of defective work.
The sensor is a transducer used to make a measurement of the physical variable. The transducer is a device that converts one type of physical variable into another form. The sensor is used to collect information about the status of manipulator and end effectors with respect to the object.
Robot is a Reprogrammable, Multi-functional Manipulator designed to move materials, parts, tools or specialized devices through variable programmed motions for performing a variety of task
A Coordinate measuring machine is an electromechanical system design to perform coordinate metrology.
CMMs are also considered as transducers that can convert physical measurements into electrical signals.
They are versatile in their capability to record measurement of complex profiles with high sensitivity (0.0025 mm) and speed.
Material handling is the art and science of moving, storing, protecting, and controlling the material
Moving: Required to create time and place utility. The value of having the material at the right time and the right place.
Storing: Provides a buffer between operations, facilitates the efficient use of people and machines.
Protecting: Includes the packaging, packing against damage and theft.
Controlling: Physical Orientation, sequence and space between material.
Automatic storage and retrieval system(as & rs)Tushar Makvana
Definition- AS/RS by material handling Institute as
“ A combination of equipment and controls which handles, stores, and retrieves materials with precision, accuracy and speed under a defined degree of automation.”
AS/RS perform a basic set of operations without human intervention:
Automatic removal of an item from a storage location
Transportation of this item to a specific processing or interface point
Automatic storage of an item in a predetermined location, having received an item from a processing or interface point.
FMS is a manufacturing philosophy based on the concept of effectively controlling material flow through a network of versatile production stations using an efficient and versatile material handling and storage system.
The FMS is most suited for the mid-variety, mid-volume production range
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
Hierarchical Digital Twin of a Naval Power SystemKerry Sado
A hierarchical digital twin of a Naval DC power system has been developed and experimentally verified. Similar to other state-of-the-art digital twins, this technology creates a digital replica of the physical system executed in real-time or faster, which can modify hardware controls. However, its advantage stems from distributing computational efforts by utilizing a hierarchical structure composed of lower-level digital twin blocks and a higher-level system digital twin. Each digital twin block is associated with a physical subsystem of the hardware and communicates with a singular system digital twin, which creates a system-level response. By extracting information from each level of the hierarchy, power system controls of the hardware were reconfigured autonomously. This hierarchical digital twin development offers several advantages over other digital twins, particularly in the field of naval power systems. The hierarchical structure allows for greater computational efficiency and scalability while the ability to autonomously reconfigure hardware controls offers increased flexibility and responsiveness. The hierarchical decomposition and models utilized were well aligned with the physical twin, as indicated by the maximum deviations between the developed digital twin hierarchy and the hardware.
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...Amil Baba Dawood bangali
Contact with Dawood Bhai Just call on +92322-6382012 and we'll help you. We'll solve all your problems within 12 to 24 hours and with 101% guarantee and with astrology systematic. If you want to take any personal or professional advice then also you can call us on +92322-6382012 , ONLINE LOVE PROBLEM & Other all types of Daily Life Problem's.Then CALL or WHATSAPP us on +92322-6382012 and Get all these problems solutions here by Amil Baba DAWOOD BANGALI
#vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore#blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #blackmagicforlove #blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #Amilbabainuk #amilbabainspain #amilbabaindubai #Amilbabainnorway #amilbabainkrachi #amilbabainlahore #amilbabaingujranwalan #amilbabainislamabad
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...
System of Limits, Fits, Tolerance and Gauging
1. SYSTEM OF LIMITS, FITS,
TOLERANCE AND GAUGING
MECHANICAL MEASUREMENT AND
METROLOGY
2. Selective Assembly Approach
• Today’s consumers desire products that are of
good quality and, at the same time, reliable
and available at attractive prices.
• Further, in order to achieve
interchangeability, it is not economical to
manufacture parts to a high degree of
accuracy.
3. Selective Assembly Approach
• It is equally important to produce the part
economically and, at the same time, maintain
the quality of the product for trouble-free
operation.
• Sometimes, for instance, if a part of minimum
limit is assembled with a mating part of
maximum limit, the fit obtained may not fully
satisfy the functional requirements of the
assembly.
4. Selective Assembly Approach
• The reason may be attributed to the issues of
accuracy and uniformity that may not be
satisfied by the certainty of the fits given
under a fully interchangeable system.
• It should be realized that, in practice,
complete interchangeability is not always
feasible; instead, selective assembly
approach can be employed.
5. Selective Assembly Approach
• In selective assembly, the manufactured
components are classified into groups
according to their sizes.
• Automatic gauging is employed for this
purpose.
• Both the mating parts are segregated
according to their sizes, and only matched
groups of mating parts are assembled.
6. Selective Assembly Approach
• This ensures complete protection and
elimination of defective assemblies, and the
matching costs are reduced because the parts
are produced with wider tolerances.
• Selective assembly finds application in
aerospace and automobile industries.
7. Selective Assembly Approach
• A very pertinent and practical example is the
manufacture and assembly of ball and bearing
units, as the tolerances desired in such industries
are very narrow and impossible to achieve
economically by any sophisticated machine tools.
• Balls are segregated into different groups
depending on their size to enable the assembly of
any bearing with balls of uniform size.
9. TOLERANCES
• To satisfy the ever-increasing demand for
accuracy, the parts have to be produced with less
dimensional variation.
• Hence, the labour and machinery required to
manufacture a part has become more expensive.
• It is essential for the manufacturer to have an in-
depth knowledge of the tolerances to
manufacture parts economically but, at the same
time, adhere to quality and reliability aspects.
10. TOLERANCES
• We know that it is not possible to precisely
manufacture components to a given
dimension because of the inherent
inaccuracies of the manufacturing processes.
• The components are manufactured in
accordance with the permissive tolerance
limits, as suggested by the designer, to
facilitate interchangeable manufacture.
11. TOLERANCES
• The permissible limits of variations in
dimensions have to be specified by the
designer in a logical manner, giving due
consideration to the functional requirements.
• The choice of the tolerances is also governed
by other factors such as manufacturing
process, cost, and standardization.
12. TOLERANCES
• Tolerance can be defined as “The magnitude
of permissible variation of a dimension or
other measured value or control criterion from
the specified value.”
• It can also be defined as “The total variation
permitted in the size of a dimension, and is the
algebraic difference between the upper and
lower acceptable dimensions.”
• It is an absolute value.
13. TOLERANCES
• The choice of setting tolerance, to a limited
extent, may be influenced and determined by
factors such as methods of tooling and
available manufacturing equipment.
• The industry follows certain approved
accuracy standards, such as ANSI (American
National Standards Institute) and ASME
(American Society of Mechanical Engineers),
to manufacture different parts.
14. MAXIMUM AND MINIMUM METAL
CONDITIONS
• Let us consider a shaft having a dimension of
• The maximum metal limit (MML) of the shaft
will have a dimension of 40.05 mm because at
this higher limit, the shaft will have the maximum
possible amount of metal.
• The shaft will have the least possible amount of
metal at a lower limit of 39.95 mm, and this limit
of the shaft is known as minimum or least metal
limit (LML).
16. MAXIMUM AND MINIMUM METAL
CONDITIONS
• Similarly, consider a hole having a dimension
of
• The hole will have a maximum possible
amount of metal at a lower limit of 44.95 mm
and the lower limit of the hole is designated
as MML.
17. MAXIMUM AND MINIMUM METAL
CONDITIONS
• For example, when a hole is drilled in a
component, minimum amount of material is
removed at the lower limit size of the hole.
• This lower limit of the hole is known as MML.
• The higher limit of the hole will be the LML.
• At a high limit of 45.05 mm, the hole will have
the least possible amount of metal.
• The maximum and minimum metal conditions
are shown in Fig.
19. FITS
• Manufactured parts are required to mate
with one another during assembly.
• The relationship between the two mating
parts that are to be assembled, that is, the
hole and the shaft, with respect to the
difference in their dimensions before
assembly is called a fit.
20. FITS
• An ideal fit is required for proper functioning
of the mating parts.
• Three basic types of fits can be identified,
depending on the actual limits of the hole or
shaft:
1. CLEARANCE FIT
2. INTERFERENCE FIT
3. TRANSITION FIT
21. CLEARANCE FIT
• The largest permissible diameter of the shaft
is smaller than the diameter of the smallest
hole.
• This type of fit always provides clearance.
Small clearances are provided for a precise fit
that can easily be assembled without the
assistance of tools.
22. CLEARANCE FIT
• For example, a shaft rotating in a bush. In case
of clearance fit, the difference between the
sizes is always positive.
• The clearance fit is described in Fig.
23. INTERFERENCE FIT
• The minimum permissible diameter of the shaft
exceeds the maximum allowable diameter of
the hole.
• This type of fit always provides interference.
• Interference fit is a form of a tight fit.
• Tools are required for the precise assembly of
two parts with an interference fit.
• When two mating parts are assembled with an
interference fit, it will be an almost permanent
assembly, that is, the parts will not come apart or
move during use.
24. INTERFERENCE FIT
• To assemble the parts with interference,
heating or cooling may be required.
• In an interference fit, the difference between
the sizes is always negative.
• Interference fits are used when accurate
location is of utmost importance and also
where such location relative to another part is
critical,
25. INTERFERENCE FIT
• For example, alignment of dowel pins. The
interference fit is illustrated in Fig.
27. TRANSITION FIT
• The diameter of the largest
permissible hole is greater than the
diameter of the smallest shaft and
the diameter of the smallest hole is
smaller than the diameter of the
largest shaft.
28. TRANSITION FIT
• In other words, the combination of
maximum diameter of the shaft and
minimum diameter of the hole results in
an interference fit, while that of
minimum diameter of the shaft and
maximum diameter of the hole yields a
clearance fit.
31. Hole Basis and Shaft Basis Systems
• To obtain the desired class of fits, either the
size of the hole or the size of the shaft must
vary.
• Two types of systems are used to represent
the three basic types of fits, namely clearance,
interference, and transition fits.
(a)HOLE BASIS SYSTEM
(b)SHAFT BASIS SYSTEM
32. Hole Basis System
• In this system, the size of the hole is kept
constant and the shaft size is varied to give
various types of fits.
• In a hole basis system, the fundamental
deviation or lower deviation of the hole is zero,
that is, the lower limit of the hole is the same as
the basic size.
• The two limits of the shaft and the higher
dimension of the hole are then varied to obtain
the desired type of fit, as illustrated in Fig.
34. Hole Basis System
• This type of system is widely adopted in
industries, as it is easier to manufacture shafts
of varying sizes to the required tolerances.
• Standard size drills or reamers can be used to
obtain a variety of fits by varying only the shaft
limits, which leads to greater economy of
production.
• The shaft can be accurately produced to the
required size by standard manufacturing
processes, and standard-size plug gauges are
used to check hole sizes accurately and
conveniently.
35. Shaft Basis System
• The system in which the dimension of the shaft
is kept constant and the hole size is varied to
obtain various types of fits is referred to as shaft
basis system.
• In this system, the fundamental deviation or the
upper deviation of the shaft is zero, that is, the
HLH equals the basic size.
• The desired class of fits is obtained by varying the
lower limit of the shaft and both limits of the
hole, as shown in Fig.
37. Shaft Basis System
• This system is not preferred in industries, as it
requires more number of standard-size tools
such as reamers, broaches, and gauges, which
increases manufacturing and inspection costs.
• It is normally preferred where the hole dimension
is dependent on the shaft dimension and is used
in situations where the standard shaft
determines the dimensions of the mating parts
such as couplings, bearings, collars, gears, and
bushings.
41. Geometric Tolerance
• Normally, tolerances are specified to indicate
the actual size or dimension of a feature such
as a hole or a shaft.
• In order to manufacture components more
accurately or with minimum dimensional
variations, the manufacturing facilities and
the labour required become more cost
intensive.
42. Geometric Tolerance
• Hence, it is essential for the manufacturer to have
an in-depth knowledge of tolerances, to
manufacture quality and reliable components
economically.
• In fact, depending on the application of the end
product, precision is engineered selectively.
• Therefore, apart from considering the actual size,
other geometric dimensions such as roundness
and straightness of a shaft have to be considered
while manufacturing components.
43. Geometric Tolerance
• The tolerances specified should also
encompass such variations.
• However, it is difficult to combine all errors of
roundness, straightness, and diameter within
a single tolerance on diameter.
• Geometric tolerance is defined as the total
amount that the dimension of a
manufactured part can vary.
44. Geometric Tolerance
• Geometric tolerance underlines the
importance of the shape of a feature as
against its size.
• This method is frequently used in industries.
• Depending on the functional requirements,
tolerance on diameter, straightness, and
roundness may be specified separately.
45. Geometric Tolerance
• Geometric tolerance can be classified as
follows:
1. Form Tolerances
2. Orientation Tolerances
3. Positional Tolerances
46. Form Tolerances
• Group of geometric tolerances applied to
individual features.
• They limit the amount of error in the shape
of a feature and are independent tolerances.
• Form tolerances as such do not require
locating dimensions.
• These include straightness, circularity,
flatness, and cylindricity.
47. Orientation Tolerances
• Orientation tolerances are a type of geometric
tolerances used to limit the direction or
orientation of a feature in relation to other
features.
• These are related tolerances.
• Perpendicularity, parallelism, and angularity
fall into this category.
48. Positional Tolerances
• Group of geometric tolerances that controls
the extent of deviation of the location of a
feature from its true position.
• This is a three-dimensional geometric
tolerance comprising position, symmetry, and
concentricity.
50. GEOMETRIC TOLERANCES
• In order to obtain a proper fit between the
two cylinders, both the centres have to be in
line with each other.
• Further, perhaps both the cylinders are
manufactured at different locations and need
to be assembled on an interchangeable basis.
• It becomes imperative to indicate how much
distance can be tolerated between the
centres of these two cylinders.
51. GEOMETRIC TOLERANCES
• This information can be represented in the
feature control frame that comprises three
boxes.
52. GEOMETRIC TOLERANCES
Indicates the feature to be
controlled, which is
represented symbolically
Distance between the two
cylinders that can be
tolerated, that is, these two
centres cannot be apart by
more than 0.01 mm
Datum is with X
54. Gauging
• Eli Whitney, who is hailed as the father of the
American system, won the first contract in
1798 for the production of muskets and
developed the gauging system.
• Richard Roberts of the United Kingdom first
used plug and collar gauges for dimensional
control. In 1857, Joseph Whitworth
demonstrated internal and external gauges
for use with a shaft-based limit system.
55. Gauging
• In mass production, components are
manufactured in accordance with the permissive
tolerance limits, as suggested by the designer.
• Production of components within the permissive
tolerance limits facilitates interchangeable
manufacture.
• It is also essential to check whether the
dimensions of the manufactured components
are in accordance with the specifications or not.
• Therefore, it is required to control the
dimensions of the components.
56. Gauging
• Several methods are available to achieve
the control on dimensions.
• Various precision measuring
instruments can be used to measure the
actual dimensions of the components,
which can be compared with the
standard specified dimensions to decide
the acceptability of these components.
57. Gauging
• In mass production, where a large
number of similar components are
manufactured on an interchangeable
basis
• Measuring the dimensions of each part
will be a time-consuming and expensive
exercise.
58. Gauging
• In addition, the actual or absolute size of a
component,
• Provided that it is within the limits specified,
is not of much importance because the
permissible limits of variations in dimensions
would have been specified by the designer in
a logical manner,
• Giving due consideration to the functional
requirements.
59. Gauging
• Therefore, in mass production, gauges can be
used to check for the compliance of the limits of
the part with the permissive tolerance limits,
instead of measuring the actual dimensions.
• The term ‘LIMIT GAUGING’ signifies the use of
gauges for checking the limits of the
components.
• Gauging plays an important role in the control of
dimensions and interchangeable manufacture.
60. Gauging
• Limit gauges ensure that the components lie
within the permissible limits, but they do not
determine the actual size or dimensions.
• Gauges are scaleless inspection tools, which are
used to check the conformance of the parts along
with their forms and relative positions of the
surfaces of the parts to the limits.
• The gauges required to check the dimensions of
the components correspond to two sizes
conforming to the maximum and minimum
limits of the components.
61. Gauging
• They are called GO gauges or NO GO or NOT
GO gauges, which correspond, respectively,
to the MML and LML of the component, as
depicted in Figs
62. Gauging
• As discussed in Previous section, MML is the
lower limit of a hole and higher limit of the
shaft and LML corresponds to the higher limit
of a hole and lower limit of the shaft.
63. Gauging
• The GO gauge manufactured to the maximum
limit will assemble with the mating (opposed)
part,
• Whereas the NOT GO gauge corresponding to
the low limit will not, hence the names GO
and NOT GO gauges, respectively.
64. Gauging
• Practically, every gauge is a replica of the part
that mates with the part for which the gauge
has been designed.
• Consider an example of the manufacture of a
cylinder that mates with a piston.
• The plug gauge, using which the cylinder bore
is checked, is a copy of the opposed part
(piston) as far as its form and size are
concerned.
67. PLAIN GAUGES
(a) According to their type:
(i) Standard gauges
(ii) Limit gauges
(b) According to their purpose:
(i) Workshop
(ii) Inspection
(iii) Reference, or master, or control gauges
68. PLAIN GAUGES
(c) According to the form of the tested surface:
(i) Plug gauges for checking holes
(ii) Snap and ring gauges for checking shafts
(d) According to their design:
(i) Single- and double-limit gauges
(ii) Single- and double-ended gauges
(iii) Fixed and adjustable gauges