This document summarizes an experiment that optimized cutting parameters for machining austenitic stainless steel AISI 316 on a CNC lathe machine. The experiment used Taguchi methods to design experiments that varied cutting speed, feed rate, and depth of cut. 27 experiments were conducted and surface roughness was measured. Analysis of variance (ANOVA) was used to determine the percentage contribution of each factor on surface roughness. The results showed that feed rate had the maximum effect on surface roughness, while depth of cut had the minimum effect. Cutting speed had the least effect on surface roughness of the workpiece surface.
IRJET- Optimization of Machining Parameters for Turning on CNC Machine of Sta...IRJET Journal
This document discusses an experimental investigation into optimizing machining parameters for turning stainless steel 316 on a CNC machine. Taguchi methods were used to determine the optimal levels for cutting speed, feed rate, and depth of cut. Eighteen experiments were conducted using an L18 orthogonal array with different combinations of the parameters. The results found that depth of cut and feed rate significantly affected material removal rate and surface roughness, while cutting speed did not have a significant impact. Analysis of variance (ANOVA) identified depth of cut as the most influential factor. Optimization found the maximum material removal rate occurred at high cutting speeds, low feed rates, and high depth of cuts.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Effect of process factors on surface roughness in dip cryogenic machining of ...eSAT Journals
Abstract A large number of structures that are being constructed at present tend to be wind-sensitive because of their slenderness, shapes, size, lightness and flexibility. With the ever increase in the vertical growth of urban cities, high rise buildings are being constructed in large numbers. In this study, analytical investigation of different shapes of buildings are taken as an example and various analytical approaches are performed on the building. These plans are modeled and wind loads are found out according to I.S 875(part 3)-1987 by taking gust factor and without taking gust factor. These models are compared in different aspects such as storey drift, storey displacement, storey shear, etc. for different shapes of buildings by using finite element software package ETAB’s 13.1.1v. Among these results, which shape of building provide sound wind loading to the structure as well as the structural efficiency would be selected. Key Words: Storey displacement, Storey drift, Storey shear, Gust, Wind load
IRJET- Review on Cutting Process Parameter for Surface Roughness During Turni...IRJET Journal
This document reviews the effects of cutting parameters like cutting speed, feed rate, nose radius, and depth of cut on surface roughness during turning operations. It discusses previous research that has investigated these effects on various materials like steel, aluminum alloys, and cast iron. The key findings of previous studies are that feed rate often has the greatest influence on surface roughness, while depth of cut and cutting speed also significantly affect results. Response surface methodology and Taguchi experimental design approaches have been used to optimize cutting parameters and predict surface roughness. Overall, controlling cutting parameters is important for achieving the desired surface quality during turning.
Taguchi based Optimization of Cutting Parameters Affecting Surface Roughness ...IRJET Journal
This document summarizes a study that used the Taguchi method to optimize cutting parameters (speed, feed rate, depth of cut) for minimizing surface roughness during CNC dry turning of 16MnCr5 steel. Experiments were conducted based on an L27 orthogonal array with three factors at three levels. Analysis of variance (ANOVA) was used to determine the percentage contribution of each factor on surface roughness. Results showed that depth of cut had the highest influence on surface roughness, followed by speed and then feed rate.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Optimization of Cutting Parameters for Surface Roughness and MRR in CNC Turni...IRJET Journal
This document summarizes an experiment that optimized cutting parameters for surface roughness and material removal rate (MRR) in CNC turning of 16MnCr5 steel. The experiment used a Taguchi design of experiments with cutting speed, feed rate, and depth of cut as parameters. An L9 orthogonal array was used to test combinations of the parameters at three levels each. The experiments measured surface roughness and MRR, which were analyzed using signal-to-noise ratios to determine the optimal settings for each response. Analysis of variance was also used to determine the effect of each parameter. The results showed that depth of cut had the highest effect on surface roughness, while feed rate had the lowest effect.
Optimization of Machining Parameters Affecting Surface Roughness of Al6082 in...IRJET Journal
The document discusses optimizing machining parameters to minimize surface roughness in dry end milling of Al6082 aluminum alloy. It reviews previous research, describes the experimental setup using Taguchi methods, and reports results from 27 experiments with varying spindle speed, feed rate, and depth of cut. Analysis found that feed rate had the greatest influence on surface roughness, with higher feed rates increasing roughness. The optimal parameters to minimize roughness were determined.
IRJET- Optimization of Machining Parameters for Turning on CNC Machine of Sta...IRJET Journal
This document discusses an experimental investigation into optimizing machining parameters for turning stainless steel 316 on a CNC machine. Taguchi methods were used to determine the optimal levels for cutting speed, feed rate, and depth of cut. Eighteen experiments were conducted using an L18 orthogonal array with different combinations of the parameters. The results found that depth of cut and feed rate significantly affected material removal rate and surface roughness, while cutting speed did not have a significant impact. Analysis of variance (ANOVA) identified depth of cut as the most influential factor. Optimization found the maximum material removal rate occurred at high cutting speeds, low feed rates, and high depth of cuts.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Effect of process factors on surface roughness in dip cryogenic machining of ...eSAT Journals
Abstract A large number of structures that are being constructed at present tend to be wind-sensitive because of their slenderness, shapes, size, lightness and flexibility. With the ever increase in the vertical growth of urban cities, high rise buildings are being constructed in large numbers. In this study, analytical investigation of different shapes of buildings are taken as an example and various analytical approaches are performed on the building. These plans are modeled and wind loads are found out according to I.S 875(part 3)-1987 by taking gust factor and without taking gust factor. These models are compared in different aspects such as storey drift, storey displacement, storey shear, etc. for different shapes of buildings by using finite element software package ETAB’s 13.1.1v. Among these results, which shape of building provide sound wind loading to the structure as well as the structural efficiency would be selected. Key Words: Storey displacement, Storey drift, Storey shear, Gust, Wind load
IRJET- Review on Cutting Process Parameter for Surface Roughness During Turni...IRJET Journal
This document reviews the effects of cutting parameters like cutting speed, feed rate, nose radius, and depth of cut on surface roughness during turning operations. It discusses previous research that has investigated these effects on various materials like steel, aluminum alloys, and cast iron. The key findings of previous studies are that feed rate often has the greatest influence on surface roughness, while depth of cut and cutting speed also significantly affect results. Response surface methodology and Taguchi experimental design approaches have been used to optimize cutting parameters and predict surface roughness. Overall, controlling cutting parameters is important for achieving the desired surface quality during turning.
Taguchi based Optimization of Cutting Parameters Affecting Surface Roughness ...IRJET Journal
This document summarizes a study that used the Taguchi method to optimize cutting parameters (speed, feed rate, depth of cut) for minimizing surface roughness during CNC dry turning of 16MnCr5 steel. Experiments were conducted based on an L27 orthogonal array with three factors at three levels. Analysis of variance (ANOVA) was used to determine the percentage contribution of each factor on surface roughness. Results showed that depth of cut had the highest influence on surface roughness, followed by speed and then feed rate.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Optimization of Cutting Parameters for Surface Roughness and MRR in CNC Turni...IRJET Journal
This document summarizes an experiment that optimized cutting parameters for surface roughness and material removal rate (MRR) in CNC turning of 16MnCr5 steel. The experiment used a Taguchi design of experiments with cutting speed, feed rate, and depth of cut as parameters. An L9 orthogonal array was used to test combinations of the parameters at three levels each. The experiments measured surface roughness and MRR, which were analyzed using signal-to-noise ratios to determine the optimal settings for each response. Analysis of variance was also used to determine the effect of each parameter. The results showed that depth of cut had the highest effect on surface roughness, while feed rate had the lowest effect.
Optimization of Machining Parameters Affecting Surface Roughness of Al6082 in...IRJET Journal
The document discusses optimizing machining parameters to minimize surface roughness in dry end milling of Al6082 aluminum alloy. It reviews previous research, describes the experimental setup using Taguchi methods, and reports results from 27 experiments with varying spindle speed, feed rate, and depth of cut. Analysis found that feed rate had the greatest influence on surface roughness, with higher feed rates increasing roughness. The optimal parameters to minimize roughness were determined.
A literature review on optimization of cutting parameters for surface roughne...IJERD Editor
This document summarizes literature on optimizing cutting parameters to improve surface roughness in turning processes. Several studies used Taguchi methods to optimize parameters like cutting speed, feed rate, depth of cut, and nose radius. Most found feed rate was the most influential parameter on surface roughness. Other key findings include that lower feed rates and depths of cut produce better surface finishes, and coatings on carbide inserts can improve tool performance and surface roughness when machining steels. Future work could optimize additional parameters and study different tool coatings.
The document describes an experiment to optimize cutting parameters during CNC turning of AISI 8620 alloy steel using response surface methodology. Speed, feed rate, and depth of cut were varied as factors in a 3-level factorial design. The response variable was surface roughness, which was measured after each experimental run. Regression analysis in Minitab was used to develop a model relating the factors to surface roughness. Response optimization was then used to determine the optimal settings of the factors to minimize surface roughness. The goal of the experiment was to evaluate the best cutting parameter settings for achieving a smooth surface finish during CNC turning of AISI 8620 alloy steel.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
optimization of process parameters for cnc turning using taguchi methods for ...INFOGAIN PUBLICATION
Coated and uncoated tool inserts offers certain degrees of control on the desired rate of tool wear and surface roughness to an extent. This work pursues the quest for realizing the optimal values for the significant process parameters that bears an influence on the response parameters. Experiments were conducted on the samples of EN 24 alloy steel material with the help of PVD coated TiAlN insert and uncoated carbide insert. The experimental runs carried out with proper variation in the levels. Levels are selected with the help of manufacturing catalogue and by pilot experimentation and results are recorded for further analysis. For this study, 9 runs designed using L9 orthogonal array of Taguchi Design of Experiment. Surface roughness was measured using a Mitutoyo surface tester at test lab and material removal rate is calculated by mathematical equation. The data was compiled into Minitab 17 software for analysis. The relationship between the machining parameters and the response variables were analyzed using the Taguchi Method. Optimization of process parameters is carried out by Grey Relational Analysis method (GRA). GRA method is a powerful and most versatile tool which can manipulate the input data as per requirement and comes with results that can be used to have best multi-objective in respective concerns
IRJET- A Review on Optimization of Cutting Parameters in Machining using ...IRJET Journal
This document reviews optimization of cutting parameters in machining using the Taguchi method. It summarizes previous research that has investigated the effects of cutting speed, depth of cut, and feed rate on surface finish in end milling processes using the Taguchi method. The document also provides background on end milling, Taguchi methods, design of experiments, and reviews several previous studies that optimized cutting parameters for different materials using Taguchi methods and found that cutting speed typically has the greatest influence on surface finish, while depth of cut tends to have the smallest effect.
OPTIMIZATION OF TURNING PROCESS PARAMETER IN DRY TURNING OF SAE52100 STEELIAEME Publication
This document summarizes an experiment to optimize surface roughness and material removal rate during dry turning of SAE52100 steel. The experiment varied cutting speed, feed rate, and depth of cut using a Taguchi L9 orthogonal array. Surface roughness increased with increasing feed rate and decreasing cutting speed. Material removal rate models were developed that showed it increases with cutting speed and depth of cut but decreases with feed rate. Analysis found feed rate has the greatest influence on surface roughness, while depth of cut most influences material removal rate. The goal of the experiment was to determine optimal machining parameters that minimize surface roughness and maximize material removal rate and productivity during dry turning of SAE52100 steel.
The document experimentally investigates the material removal rate (MRR) and tool wear in turning hardened AISI 52100 steel using the Taguchi technique. Experiments were conducted using different cutting speeds, feed rates, and depths of cut based on an L9 orthogonal array. The results were analyzed using signal-to-noise ratios and ANOVA to determine the optimal process parameters for maximizing MRR and minimizing tool wear. The analysis found that cutting speed had the greatest influence on MRR, followed by depth of cut and feed rate. The optimal parameters for MRR were a cutting speed of 1120 rpm, feed rate of 0.12 mm/rev, and depth of cut of 0.4 mm.
IRJET- A Review on: Parametric Study for Optimization of CNC Turning Process ...IRJET Journal
This document reviews research on optimizing CNC turning process parameters to minimize surface roughness. It summarizes 10 research papers that studied the effects of cutting speed, feed rate, depth of cut, cutting tool type, and cooling conditions on surface roughness when turning various materials like steel, aluminum, and titanium. The document finds that feed rate typically has the largest effect on surface roughness, followed by cutting speed, while depth of cut has a smaller impact. It recommends using techniques like Taguchi methods, response surface methodology, and ANOVA to determine the optimal process parameters that achieve the minimum possible surface roughness.
Analysis of process parameters in dry machining of en 31 steel by grey relati...IAEME Publication
This paper presents the optimization of surface roughness & material removal rate in dry turning of EN-31 steel.Carbide inserts were used for machining of EN-31 to study effects of process parameters [Cutting speed (S), Feed (F) and depth of cut (d)]. These models can be effectively used to predict the surface roughness (Ra) of the workpiece. The big challenge of the Micro, small& medium industries in India for achieving high quality products with increased productivity.Paper presentswork of an investigation of turning process parameters on EN-31 material, for optimization of surface roughness, material removal rate.The experiment is carried out by considering three controllable input variables namely cutting speed, feed rate, and depth of cut.The design of experiment and optimization of surface roughness is carried out by using Taguchi L9 orthogonal array & Grey Relational analysis.
This document summarizes an experimental study on optimizing surface roughness and material removal rate during turning of AISI D2 steel. 27 experiments were conducted using a full factorial design varying cutting speed, feed rate, and depth of cut. Cutting speed had the greatest effect on surface roughness, while feed rate and depth of cut most influenced material removal rate. Analysis of variance found cutting speed contributed 79.8% to surface roughness. Grey relational analysis identified the optimal condition for low surface roughness as low feed rate, low depth of cut, and high cutting speed.
Optimization of turning process parameter in dry turning of sae52100 steelIAEME Publication
This document discusses optimizing surface roughness and material removal rate in dry turning of SAE52100 steel. Experiments were conducted using different cutting speeds, feeds, and depths of cut. Surface roughness and material removal rate were measured for each experimental condition. The results were analyzed using Taguchi methods to determine the optimal levels for each process parameter to minimize surface roughness and maximize material removal rate. The analysis found that feed rate had the greatest influence on surface roughness, while cutting speed had the greatest influence on material removal rate.
A Review on Optimization of Cutting Parameters for Improvement of Surface Rou...IRJET Journal
This document summarizes a study that used the Taguchi method and Grey Taguchi approach to optimize cutting parameters for improving surface roughness and tool life during low carbon steel turning. The study used an L27 orthogonal array to experiment with cutting speed, feed rate, depth of cut, and corner radius. Surface roughness and flank wear were evaluated as output parameters. Analysis of variance found that cutting speed most significantly affects surface roughness and flank wear, followed by depth of cut, feed rate, and corner radius. The optimized parameters were determined to be a cutting speed of 325m/min, feed rate of 0.1 mm/rev, depth of cut of 0.25mm, and corner radius of 0.8mm.
Determining the Influence of Various Cutting Parameters on Surface Roughness ...IOSR Journals
The document describes an experimental investigation that analyzed the effect of various cutting parameters on surface roughness during wet CNC turning of AISI 1040 medium carbon steel. The parameters tested included cutting speed, feed rate, depth of cut, cutting fluid concentration, and two different cutting fluids. Custom experimental design and statistical analysis using JMP software revealed that feed rate had the most significant influence on surface roughness, and that there was no significant difference in surface roughness between the two cutting fluids tested.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
The document discusses optimizing parameters for boring operations. It aims to achieve a surface finish less than 2 micrometers and bore diameter of 70 mm. Experiments were conducted varying speed, feed rate, and depth of cut. Analysis of variance and response surface methodology were used to analyze results. The optimal parameters were found to be a speed of 1000 rpm and feed rate of 100 mm/min, predicted to achieve a surface roughness of 1.843 micrometers and bore diameter of 70.005 mm. Validation experiments confirmed the predicted results were within acceptable ranges.
Multi-Objective Optimization ( Surface Roughness & Material Removal Rate) of ...IJERA Editor
The present study applied Taguchi method through a case study in straight turning of AISI 202 stainless steel bar on CNC Machine ( Mfd by ACE DESIGNERS) using Titanium Carbide tool for the optimization of Material removal rate, Surface Roughness and tool wear process parameter.The study aimed at evaluating the best process environment which could simultaneously satisfy requirements of both quality as well as productivity with special emphasis on maximizing material removal rate and minimizing surface roughness and tool flank wear at various combination of cutting speed, feed, depth of cut. The predicted optimal setting ensured maximum MRR and minimum surface roughness and tool wear. Since optimum material removal rate is desired, so higher the better criteria of Taguchi signal to noise ratio is used for MRR – SNs = -10 log(Sy2/n) For surface roughness and tool wear – SNL = -10 log(S(1/y2)/n) The results have been verified with the help of S/N Ratios calculation and various graphs have been plotted to show the below mentioned observations.
a) MRR first increases with increase in cutting speed and then decreases.
b) With the increase in feed, MRR increases.
c) With the increase in depth of cut, MRR first increases and then decreases.
d) With the increase in cutting speed, Surface Roughness first decreases and then increases.
e) With the increase in feed, Surface Roughness increases.
f) With the increase in depth of cut, Surface Roughness first increases and then decreases.
IRJET-Optimization of Machining Parameters Affecting Metal Removal Rate of Al...IRJET Journal
The document discusses optimizing machining parameters to increase the metal removal rate in dry end milling of aluminum alloy 6082. The machining parameters investigated are spindle speed, feed rate, and depth of cut. Experiments were performed using a Taguchi design of experiments with the parameters tested at three levels. The experimental data was analyzed using Minitab software to identify the most significant factor affecting metal removal rate. The goal is to determine the optimal settings of the machining parameters to maximize productivity during end milling of aluminum alloy 6082.
IRJET- Investigation on Metal Removal Rate by Changing Various Parameters Lik...IRJET Journal
This document investigates the effect of changing machining parameters like RPM, feed rate, and depth of cut on the material removal rate when turning mild steel. An experiment was conducted using a Taguchi L9 orthogonal array to test different parameter combinations. The results show that material removal rate increases with increases in RPM, feed rate, and depth of cut up to a point, after which further increases can damage the material and tool. An optimal combination is needed to maximize productivity while maintaining quality. The conclusions determine the best parameter ranges for improving efficiency in turning mild steel.
COMPARISON OF SURFACE ROUGHNESS OF COLDWORK AND HOT WORK TOOL STEELS IN HARD ...ijmech
The hard turning process has been attracting interest in different industrial sectors for finishing operations
of hard materials at its hardened state.Surface roughness is investigated in hard turning of AISI D3 and
AISI H13 steels of same hardness 62HRC. In this paper, an attempt has been made to model and predict
the surface roughness in hard turning of AISI D3 and AISI H13 hardened steels using Response Surface
Methodology (RSM). The combined effects of three machining parameters such as cutting speed, feed rate
and depth of cut are investigated for main performance characteristic that is surface roughness. RSM
based Central Composite Design (CCD) is applied as an experimental design. Al2O3/TiC mixed ceramic
tool with corner radius 0.8 mm is employed to accomplish 20 tests with six center points. The acceptability
of the developed models is checked using Analysis of Variance (ANOVA).The combined effects of cutting
speed; feed rate and depth of cut are investigated using surface plots.
A review on effect of various parameters on cutting tool in orthogonal metal ...eSAT Journals
Abstract
In recent years there is great progress in the field of tool design. Tool is an important factor for machinability process. In the
metal cutting process various cutting parameters affecting on the cutting tool. The various parameters include as cutting speed,
feed rate, depth of cut, rake angle. The effect of these parameters on the cutting forces, tool temperature, and surface roughness
studied. This helps in evaluating the tool life and tool wear. This effect of parameters on tool is important for efficient machining
and machining conditions. The paper also covers the effect of cutting parameters on the chip formation and residual stresses
produced during cutting process.
Keywords: Cutting parameters, orthogonal, cutting process, cutting tool
Effectiveness of multilayer coated tool in turning of aisi 430 f steeleSAT Journals
Abstract This paper presents minimization of surface roughness in dry turning of AISI 430F steel using TiN-TiCN-Al2O3-ZrCN multilayer coated cemented carbide & cryo-treated inserts. Effect of cutting velocity, feed rate, depth of cut & machining duration is studied on the surface roughness. Taguchi’s design of experiment is used to find the optimum factor levels. It is found that the feed rate has much effect in producing lower surface roughness followed by speed. The depth of cut has lesser role on surface roughness. The result of Taguchi method shows that cutting velocity of 250m/min, feed rate of 0.25 mm/rev and depth of cut of 0.3mm should be maintained as optimal parameter settings for both coated and cryo-treated tools. Cryo-treated tools perform better. Keywords: Cryo-treatment, Dry Turning, Surface roughness, Taguchi Method
A literature review on optimization of cutting parameters for surface roughne...IJERD Editor
This document summarizes literature on optimizing cutting parameters to improve surface roughness in turning processes. Several studies used Taguchi methods to optimize parameters like cutting speed, feed rate, depth of cut, and nose radius. Most found feed rate was the most influential parameter on surface roughness. Other key findings include that lower feed rates and depths of cut produce better surface finishes, and coatings on carbide inserts can improve tool performance and surface roughness when machining steels. Future work could optimize additional parameters and study different tool coatings.
The document describes an experiment to optimize cutting parameters during CNC turning of AISI 8620 alloy steel using response surface methodology. Speed, feed rate, and depth of cut were varied as factors in a 3-level factorial design. The response variable was surface roughness, which was measured after each experimental run. Regression analysis in Minitab was used to develop a model relating the factors to surface roughness. Response optimization was then used to determine the optimal settings of the factors to minimize surface roughness. The goal of the experiment was to evaluate the best cutting parameter settings for achieving a smooth surface finish during CNC turning of AISI 8620 alloy steel.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
optimization of process parameters for cnc turning using taguchi methods for ...INFOGAIN PUBLICATION
Coated and uncoated tool inserts offers certain degrees of control on the desired rate of tool wear and surface roughness to an extent. This work pursues the quest for realizing the optimal values for the significant process parameters that bears an influence on the response parameters. Experiments were conducted on the samples of EN 24 alloy steel material with the help of PVD coated TiAlN insert and uncoated carbide insert. The experimental runs carried out with proper variation in the levels. Levels are selected with the help of manufacturing catalogue and by pilot experimentation and results are recorded for further analysis. For this study, 9 runs designed using L9 orthogonal array of Taguchi Design of Experiment. Surface roughness was measured using a Mitutoyo surface tester at test lab and material removal rate is calculated by mathematical equation. The data was compiled into Minitab 17 software for analysis. The relationship between the machining parameters and the response variables were analyzed using the Taguchi Method. Optimization of process parameters is carried out by Grey Relational Analysis method (GRA). GRA method is a powerful and most versatile tool which can manipulate the input data as per requirement and comes with results that can be used to have best multi-objective in respective concerns
IRJET- A Review on Optimization of Cutting Parameters in Machining using ...IRJET Journal
This document reviews optimization of cutting parameters in machining using the Taguchi method. It summarizes previous research that has investigated the effects of cutting speed, depth of cut, and feed rate on surface finish in end milling processes using the Taguchi method. The document also provides background on end milling, Taguchi methods, design of experiments, and reviews several previous studies that optimized cutting parameters for different materials using Taguchi methods and found that cutting speed typically has the greatest influence on surface finish, while depth of cut tends to have the smallest effect.
OPTIMIZATION OF TURNING PROCESS PARAMETER IN DRY TURNING OF SAE52100 STEELIAEME Publication
This document summarizes an experiment to optimize surface roughness and material removal rate during dry turning of SAE52100 steel. The experiment varied cutting speed, feed rate, and depth of cut using a Taguchi L9 orthogonal array. Surface roughness increased with increasing feed rate and decreasing cutting speed. Material removal rate models were developed that showed it increases with cutting speed and depth of cut but decreases with feed rate. Analysis found feed rate has the greatest influence on surface roughness, while depth of cut most influences material removal rate. The goal of the experiment was to determine optimal machining parameters that minimize surface roughness and maximize material removal rate and productivity during dry turning of SAE52100 steel.
The document experimentally investigates the material removal rate (MRR) and tool wear in turning hardened AISI 52100 steel using the Taguchi technique. Experiments were conducted using different cutting speeds, feed rates, and depths of cut based on an L9 orthogonal array. The results were analyzed using signal-to-noise ratios and ANOVA to determine the optimal process parameters for maximizing MRR and minimizing tool wear. The analysis found that cutting speed had the greatest influence on MRR, followed by depth of cut and feed rate. The optimal parameters for MRR were a cutting speed of 1120 rpm, feed rate of 0.12 mm/rev, and depth of cut of 0.4 mm.
IRJET- A Review on: Parametric Study for Optimization of CNC Turning Process ...IRJET Journal
This document reviews research on optimizing CNC turning process parameters to minimize surface roughness. It summarizes 10 research papers that studied the effects of cutting speed, feed rate, depth of cut, cutting tool type, and cooling conditions on surface roughness when turning various materials like steel, aluminum, and titanium. The document finds that feed rate typically has the largest effect on surface roughness, followed by cutting speed, while depth of cut has a smaller impact. It recommends using techniques like Taguchi methods, response surface methodology, and ANOVA to determine the optimal process parameters that achieve the minimum possible surface roughness.
Analysis of process parameters in dry machining of en 31 steel by grey relati...IAEME Publication
This paper presents the optimization of surface roughness & material removal rate in dry turning of EN-31 steel.Carbide inserts were used for machining of EN-31 to study effects of process parameters [Cutting speed (S), Feed (F) and depth of cut (d)]. These models can be effectively used to predict the surface roughness (Ra) of the workpiece. The big challenge of the Micro, small& medium industries in India for achieving high quality products with increased productivity.Paper presentswork of an investigation of turning process parameters on EN-31 material, for optimization of surface roughness, material removal rate.The experiment is carried out by considering three controllable input variables namely cutting speed, feed rate, and depth of cut.The design of experiment and optimization of surface roughness is carried out by using Taguchi L9 orthogonal array & Grey Relational analysis.
This document summarizes an experimental study on optimizing surface roughness and material removal rate during turning of AISI D2 steel. 27 experiments were conducted using a full factorial design varying cutting speed, feed rate, and depth of cut. Cutting speed had the greatest effect on surface roughness, while feed rate and depth of cut most influenced material removal rate. Analysis of variance found cutting speed contributed 79.8% to surface roughness. Grey relational analysis identified the optimal condition for low surface roughness as low feed rate, low depth of cut, and high cutting speed.
Optimization of turning process parameter in dry turning of sae52100 steelIAEME Publication
This document discusses optimizing surface roughness and material removal rate in dry turning of SAE52100 steel. Experiments were conducted using different cutting speeds, feeds, and depths of cut. Surface roughness and material removal rate were measured for each experimental condition. The results were analyzed using Taguchi methods to determine the optimal levels for each process parameter to minimize surface roughness and maximize material removal rate. The analysis found that feed rate had the greatest influence on surface roughness, while cutting speed had the greatest influence on material removal rate.
A Review on Optimization of Cutting Parameters for Improvement of Surface Rou...IRJET Journal
This document summarizes a study that used the Taguchi method and Grey Taguchi approach to optimize cutting parameters for improving surface roughness and tool life during low carbon steel turning. The study used an L27 orthogonal array to experiment with cutting speed, feed rate, depth of cut, and corner radius. Surface roughness and flank wear were evaluated as output parameters. Analysis of variance found that cutting speed most significantly affects surface roughness and flank wear, followed by depth of cut, feed rate, and corner radius. The optimized parameters were determined to be a cutting speed of 325m/min, feed rate of 0.1 mm/rev, depth of cut of 0.25mm, and corner radius of 0.8mm.
Determining the Influence of Various Cutting Parameters on Surface Roughness ...IOSR Journals
The document describes an experimental investigation that analyzed the effect of various cutting parameters on surface roughness during wet CNC turning of AISI 1040 medium carbon steel. The parameters tested included cutting speed, feed rate, depth of cut, cutting fluid concentration, and two different cutting fluids. Custom experimental design and statistical analysis using JMP software revealed that feed rate had the most significant influence on surface roughness, and that there was no significant difference in surface roughness between the two cutting fluids tested.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
The document discusses optimizing parameters for boring operations. It aims to achieve a surface finish less than 2 micrometers and bore diameter of 70 mm. Experiments were conducted varying speed, feed rate, and depth of cut. Analysis of variance and response surface methodology were used to analyze results. The optimal parameters were found to be a speed of 1000 rpm and feed rate of 100 mm/min, predicted to achieve a surface roughness of 1.843 micrometers and bore diameter of 70.005 mm. Validation experiments confirmed the predicted results were within acceptable ranges.
Multi-Objective Optimization ( Surface Roughness & Material Removal Rate) of ...IJERA Editor
The present study applied Taguchi method through a case study in straight turning of AISI 202 stainless steel bar on CNC Machine ( Mfd by ACE DESIGNERS) using Titanium Carbide tool for the optimization of Material removal rate, Surface Roughness and tool wear process parameter.The study aimed at evaluating the best process environment which could simultaneously satisfy requirements of both quality as well as productivity with special emphasis on maximizing material removal rate and minimizing surface roughness and tool flank wear at various combination of cutting speed, feed, depth of cut. The predicted optimal setting ensured maximum MRR and minimum surface roughness and tool wear. Since optimum material removal rate is desired, so higher the better criteria of Taguchi signal to noise ratio is used for MRR – SNs = -10 log(Sy2/n) For surface roughness and tool wear – SNL = -10 log(S(1/y2)/n) The results have been verified with the help of S/N Ratios calculation and various graphs have been plotted to show the below mentioned observations.
a) MRR first increases with increase in cutting speed and then decreases.
b) With the increase in feed, MRR increases.
c) With the increase in depth of cut, MRR first increases and then decreases.
d) With the increase in cutting speed, Surface Roughness first decreases and then increases.
e) With the increase in feed, Surface Roughness increases.
f) With the increase in depth of cut, Surface Roughness first increases and then decreases.
IRJET-Optimization of Machining Parameters Affecting Metal Removal Rate of Al...IRJET Journal
The document discusses optimizing machining parameters to increase the metal removal rate in dry end milling of aluminum alloy 6082. The machining parameters investigated are spindle speed, feed rate, and depth of cut. Experiments were performed using a Taguchi design of experiments with the parameters tested at three levels. The experimental data was analyzed using Minitab software to identify the most significant factor affecting metal removal rate. The goal is to determine the optimal settings of the machining parameters to maximize productivity during end milling of aluminum alloy 6082.
IRJET- Investigation on Metal Removal Rate by Changing Various Parameters Lik...IRJET Journal
This document investigates the effect of changing machining parameters like RPM, feed rate, and depth of cut on the material removal rate when turning mild steel. An experiment was conducted using a Taguchi L9 orthogonal array to test different parameter combinations. The results show that material removal rate increases with increases in RPM, feed rate, and depth of cut up to a point, after which further increases can damage the material and tool. An optimal combination is needed to maximize productivity while maintaining quality. The conclusions determine the best parameter ranges for improving efficiency in turning mild steel.
COMPARISON OF SURFACE ROUGHNESS OF COLDWORK AND HOT WORK TOOL STEELS IN HARD ...ijmech
The hard turning process has been attracting interest in different industrial sectors for finishing operations
of hard materials at its hardened state.Surface roughness is investigated in hard turning of AISI D3 and
AISI H13 steels of same hardness 62HRC. In this paper, an attempt has been made to model and predict
the surface roughness in hard turning of AISI D3 and AISI H13 hardened steels using Response Surface
Methodology (RSM). The combined effects of three machining parameters such as cutting speed, feed rate
and depth of cut are investigated for main performance characteristic that is surface roughness. RSM
based Central Composite Design (CCD) is applied as an experimental design. Al2O3/TiC mixed ceramic
tool with corner radius 0.8 mm is employed to accomplish 20 tests with six center points. The acceptability
of the developed models is checked using Analysis of Variance (ANOVA).The combined effects of cutting
speed; feed rate and depth of cut are investigated using surface plots.
A review on effect of various parameters on cutting tool in orthogonal metal ...eSAT Journals
Abstract
In recent years there is great progress in the field of tool design. Tool is an important factor for machinability process. In the
metal cutting process various cutting parameters affecting on the cutting tool. The various parameters include as cutting speed,
feed rate, depth of cut, rake angle. The effect of these parameters on the cutting forces, tool temperature, and surface roughness
studied. This helps in evaluating the tool life and tool wear. This effect of parameters on tool is important for efficient machining
and machining conditions. The paper also covers the effect of cutting parameters on the chip formation and residual stresses
produced during cutting process.
Keywords: Cutting parameters, orthogonal, cutting process, cutting tool
Effectiveness of multilayer coated tool in turning of aisi 430 f steeleSAT Journals
Abstract This paper presents minimization of surface roughness in dry turning of AISI 430F steel using TiN-TiCN-Al2O3-ZrCN multilayer coated cemented carbide & cryo-treated inserts. Effect of cutting velocity, feed rate, depth of cut & machining duration is studied on the surface roughness. Taguchi’s design of experiment is used to find the optimum factor levels. It is found that the feed rate has much effect in producing lower surface roughness followed by speed. The depth of cut has lesser role on surface roughness. The result of Taguchi method shows that cutting velocity of 250m/min, feed rate of 0.25 mm/rev and depth of cut of 0.3mm should be maintained as optimal parameter settings for both coated and cryo-treated tools. Cryo-treated tools perform better. Keywords: Cryo-treatment, Dry Turning, Surface roughness, Taguchi Method
Analysis of process parameters in dry machining of en 31 steel by grey relati...IAEME Publication
This document summarizes a study that optimized surface roughness and material removal rate when dry turning the steel alloy EN-31. Experiments were conducted using carbide inserts with cutting speed, feed rate, and depth of cut as controllable variables. Taguchi's design of experiments and Grey relational analysis were used to optimize surface roughness. The literature review found that feed rate is often the most influential factor on surface roughness in hard turning steel alloys like EN-31. The goal of the study was to determine optimal machining parameters in dry turning of EN-31 to improve productivity for small and medium industries in India.
ANALYSIS OF PROCESS PARAMETERS IN DRY MACHINING OF EN-31 STEEL by GREY RELATI...IAEME Publication
This paper presents the optimization of surface roughness & material removal rate in dry turning of EN-31 steel.Carbide inserts were used for machining of EN-31 to study effects of process parameters [Cutting speed (S), Feed (F) and depth o f cut (d)]. These models can be effectively used to predict the surface roughness (Ra) of the workpiece. The big challenge of the Micro, small& medium industries in India for achieving high quality products with increased productivity.Paper presents work of an investigation of turning process parameters on EN-31 material, for optimization of surface roughness, material removal rate.The experiment is carried out by considering three controllable input variables namely cutting speed, feed rate, and depth of cut.The design of experiment and optimization of surface roughness is carried out by using Taguchi L9 orthogonal array & Grey Relational analysis.
Effects of Cutting Tool Parameters on Surface Roughnessirjes
This paper presents of the influence on surface roughness of Co28Cr6Mo medical alloy machined
on a CNC lathe based on cutting parameters (rotational speed, feed rate, depth of cut and nose radius).The
influences of cutting parameters have been presented in graphical form for understanding. To achieve the
minimum surface roughness, the optimum values obtained for rpm, feed rate, depth of cut and nose radius were
respectively, 318 rpm, 0,1 mm/rev, 0,7 mm and 0,8 mm. Maximum surface roughness has been revealed the
values obtained for rpm, feed rate, depth of cut and nose radius were respectively, 318 rpm, 0,25 mm/rev, 0,9
mm and 0,4 mm.
“Optimization of Cutting Parameters for Turning AISI 316 Stainless Steel Base...IOSRJMCE
The objective of this work is the optimization of the cutting parameters for turning AISI 316 stainless steel to achieve the better surface finish using Taguchi’s methodology. Taguchi Parameter Design is a powerful and efficient method for optimizing quality and performance output of manufacturing processes, thus a powerful tool for meeting this challenge. This work discusses an investigation into the use of Taguchi Parameter Design for optimizing surface roughness generated by a Turning operation. In this method, four control factors viz. cutting speed, feed rate, depth of cut, three different cutting fluids (sherol B, sherol ENF, straight cutting oil) and one work piece material (AISI 316 stainless steel) were investigated at three different levels and the turning operations are done on Banka 1000 lathe machine. Cutting speed followed by cutting fluid has the significant role. The quality characteristic identified is surface roughness. Experiments carried out using L9 (34 ) Orthogonal Array with three different levels of control factors.The test results were analyzed using “smallerthe-better” criteria for Signal-to-Noise ratio in order to optimize the process. The experimental results were analyzed, conformed and successfully used to achieve good surface finish on work piece materials.
IRJET- Analysis of Cutting Process Parameter During Turning of EN 31 for Mini...IRJET Journal
This document analyzes cutting process parameters to minimize surface roughness during turning of EN 31 steel. Experiments were conducted using a Taguchi design of experiments with cutting speed, feed rate, and tool nose radius as parameters. Measurements showed feed rate had the greatest influence on surface roughness, followed by nose radius. The optimal combination for minimum roughness was a feed rate of 0.025 mm/rev, nose radius of 0.8 mm, and cutting speed of 210 m/min.
Experimental Investigation of Machining Parameters for Aluminum 6061 T6 Alloyijtsrd
In the present work, Turning Parameters were optimized using Taguchi Method. Also, the effect of turning parameters such as rotational speed, feed rate, depth of cut and material removal rate on surface roughness of Aluminum 6061 T6 alloy was investigated. L9 Taguchi’s method was used for designing the experiments and optimization of turning parameters. Nine experiments were conducted with four factors having three levels for each factor. Results revealed that spindle speed has a significant effect on surface roughness and it is the most dominating factor affecting the surface roughness with contribution of 52.38 . The optimal parameter combination of Aluminum 6061 T6 alloy bar for minimum surface roughness is found to be A2 B1 C2 D i.e., rotational spindle speed A at 900 rpm, feed rate B at 90 mm min and depth of cut C at 0.8 mm, and material removal rate D . Hardeep Singh | Ganga Singh | Dr. Dinesh Kumar "Experimental Investigation of Machining Parameters for Aluminum 6061-T6 Alloy" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-6 | Issue-7 , December 2022, URL: https://www.ijtsrd.com/papers/ijtsrd52611.pdf Paper URL: https://www.ijtsrd.com/engineering/mechanical-engineering/52611/experimental-investigation-of-machining-parameters-for-aluminum-6061t6-alloy/hardeep-singh
Application of taguchi method in optimization of tool flank wear width ...Alexander Decker
1) The document applies Taguchi techniques to optimize tool flank wear width in turning AISI 1045 steel. An L9 orthogonal array is used to experiment with cutting speed, feed rate, and depth of cut as parameters.
2) Analysis of mean responses and S/N ratios found minimum wear at high speed, low feed rate, and shallow depth of cut. ANOVA showed cutting speed most influential.
3) Confirmation experiments verified 23.85% reduction in wear width at the optimal parameter levels of high speed, low feed rate, and shallow depth of cut.
This document summarizes an investigation into flank wear on minimal cutting fluid application during turning of OHNS steel. Seven input parameters were varied at three levels in a 27-run Taguchi experiment. Analysis found that feed rate had the greatest influence on flank wear, cutting temperature, and chip thickness based on ANOVA. Optimal cutting and fluid application parameters were determined to be a cutting speed of 168.23 m/min, feed of 0.04 mm/rev, depth of cut of 1 mm, pressure of 100 bar, frequency of 900 pulses/min, application rate of 3 ml/min, and fluid composition of 20%. The study provides optimized parameters for improved tool performance during turning of OHNS steel with minimal cutting fluid application.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
This document discusses assessing cutting fluid as a key parameter in evaluating surface finish for CNC turning operations. It begins with an abstract that outlines exploring tool-workpiece combinations of HCHCr material with cemented carbide and CBN tools. Statistical analysis methods like ANOVA, DOE and regression will be used to identify optimal machining parameters. Experimental validation will then be conducted to evaluate the determined parameters. A literature review covers previous research on optimizing surface roughness in turning. The problem statement identifies that variation in speed, feed, depth of cut and coolant type influence material removal rate and surface roughness. The objectives are to determine optimal values for these parameters to achieve desired surface finish with satisfactory material removal. The methodology will use analytical and physical
This document summarizes research on optimizing surface finish in CNC turning operations. It reviews several studies that investigated the effects of cutting parameters such as speed, feed rate, depth of cut, and cutting fluid on surface roughness when machining materials like steel, aluminum alloys, and super alloys. Statistical methods like the Taguchi method, ANOVA, and grey relational analysis were used to identify optimum cutting conditions and the most influential parameters. The goal of the studies was to determine cutting parameters that produce the lowest surface roughness, maximize material removal rate, and minimize power consumption and cutting time.
Optimization of Material Removal Rate & Surface Roughness in Dry Turning of M...IJERA Editor
Optimization of machining parameters is valuable to maintain the accuracy of the components and to minimize
the cost of machining. Surface finish is an important measure for the quality of the machined parts. The present
work is an experimental investigation to study the effect of machining parameters on Material Removal Rate
and Surface Roughness in dry turning of medium carbon steel EN19. Taguchi’s single objective optimization
method was used to find the effect of input parameters on the responses. The experiments were conducted as per
Taguchi’s L9 Orthogonal Array on CNC lathe under dry conditions. Cutting parameters of speed, feed and
depth of cut were taken as inputs and machining was done by PVD TiAlN tool. Regression models for the
responses were prepared by using MINITAB-16 software. Analysis of variance (ANOVA) was used to find the
influence of machining parameters on the responses. From the ANOVA results, it is clear that speed has high
influence followed by feed and depth of cut has very low influence in achieving the optimum values for both
Material Removal Rate and Surface Roughness. Finally, experimental and Regression values of responses were
compared. From the results, it is found that both the values are close to each other hence, the regression models
prepared were more accurate and adequate. Percentage of errors between experimental and regression values
were calculated and they found in the range of ±0.20.
Experimental Investigation and Parametric Studies of Surface Roughness Analys...IJMER
The modern machining industries are focused on achieving high quality, in terms of
part/component accuracy, surface finish, high production rate and increase in product life. Surface
roughness of machined components has received serious attention of researchers for many years. It has
been an important design feature and quality measure in machining process. There are a large number of
parameters which affect the surface roughness. The typical controllable parameters for the CNC machines
include cutting tool variables, work piece material variables, cutting conditions etc. The desired output is
surface roughness, material removal rate, tool wear, etc. Optimization of machining parameters needs to
determine the most significant parameter for required output. Many techniques are used for optimization
of machining parameters including Taguchi, RSM and ANOVA approach to determine most significant
parameter.
The present work is therefore in a direction to integrate effect of various parameters which affect
the surface roughness. This paper investigates the parameters affecting the surface roughness and / or
material removal rate with CNC turning process studied by researchers. It also discusses some other
parameters such as cutting force and power consumption in different conditions.
Analysis of Surface Roughness for Cylindrical Stainless Steel Pipe (Ss 3163) ...IRJET Journal
This document discusses using artificial neural networks (ANN) to predict surface roughness in cylindrical stainless steel pipes machined using CNC lathe turning. Surface roughness is an important quality metric that is influenced by machining parameters like cutting speed, feed rate, depth of cut, and tool geometry. The document reviews previous research applying ANN and other methods to model surface roughness. It then describes an experiment using ANN to develop a model relating machining parameters to surface roughness measured from turning 316L stainless steel pipes on a CNC lathe. The results indicate ANN is an effective method for accurately predicting surface roughness based on cutting conditions.
Similar to Optimization of Cutting Parameters Based on Taugchi Method of AISI316 using CNC Lathe Machine (17)
TUNNELING IN HIMALAYAS WITH NATM METHOD: A SPECIAL REFERENCES TO SUNGAL TUNNE...IRJET Journal
1) The document discusses the Sungal Tunnel project in Jammu and Kashmir, India, which is being constructed using the New Austrian Tunneling Method (NATM).
2) NATM involves continuous monitoring during construction to adapt to changing ground conditions, and makes extensive use of shotcrete for temporary tunnel support.
3) The methodology section outlines the systematic geotechnical design process for tunnels according to Austrian guidelines, and describes the various steps of NATM tunnel construction including initial and secondary tunnel support.
STUDY THE EFFECT OF RESPONSE REDUCTION FACTOR ON RC FRAMED STRUCTUREIRJET Journal
This study examines the effect of response reduction factors (R factors) on reinforced concrete (RC) framed structures through nonlinear dynamic analysis. Three RC frame models with varying heights (4, 8, and 12 stories) were analyzed in ETABS software under different R factors ranging from 1 to 5. The results showed that displacement increased as the R factor decreased, indicating less linear behavior for lower R factors. Drift also decreased proportionally with increasing R factors from 1 to 5. Shear forces in the frames decreased with higher R factors. In general, R factors of 3 to 5 produced more satisfactory performance with less displacement and drift. The displacement variations between different building heights were consistent at different R factors. This study evaluated how R factors influence
A COMPARATIVE ANALYSIS OF RCC ELEMENT OF SLAB WITH STARK STEEL (HYSD STEEL) A...IRJET Journal
This study compares the use of Stark Steel and TMT Steel as reinforcement materials in a two-way reinforced concrete slab. Mechanical testing is conducted to determine the tensile strength, yield strength, and other properties of each material. A two-way slab design adhering to codes and standards is executed with both materials. The performance is analyzed in terms of deflection, stability under loads, and displacement. Cost analyses accounting for material, durability, maintenance, and life cycle costs are also conducted. The findings provide insights into the economic and structural implications of each material for reinforcement selection and recommendations on the most suitable material based on the analysis.
Effect of Camber and Angles of Attack on Airfoil CharacteristicsIRJET Journal
This document discusses a study analyzing the effect of camber, position of camber, and angle of attack on the aerodynamic characteristics of airfoils. Sixteen modified asymmetric NACA airfoils were analyzed using computational fluid dynamics (CFD) by varying the camber, camber position, and angle of attack. The results showed the relationship between these parameters and the lift coefficient, drag coefficient, and lift to drag ratio. This provides insight into how changes in airfoil geometry impact aerodynamic performance.
A Review on the Progress and Challenges of Aluminum-Based Metal Matrix Compos...IRJET Journal
This document reviews the progress and challenges of aluminum-based metal matrix composites (MMCs), focusing on their fabrication processes and applications. It discusses how various aluminum MMCs have been developed using reinforcements like borides, carbides, oxides, and nitrides to improve mechanical and wear properties. These composites have gained prominence for their lightweight, high-strength and corrosion resistance properties. The document also examines recent advancements in fabrication techniques for aluminum MMCs and their growing applications in industries such as aerospace and automotive. However, it notes that challenges remain around issues like improper mixing of reinforcements and reducing reinforcement agglomeration.
Dynamic Urban Transit Optimization: A Graph Neural Network Approach for Real-...IRJET Journal
This document discusses research on using graph neural networks (GNNs) for dynamic optimization of public transportation networks in real-time. GNNs represent transit networks as graphs with nodes as stops and edges as connections. The GNN model aims to optimize networks using real-time data on vehicle locations, arrival times, and passenger loads. This helps increase mobility, decrease traffic, and improve efficiency. The system continuously trains and infers to adapt to changing transit conditions, providing decision support tools. While research has focused on performance, more work is needed on security, socio-economic impacts, contextual generalization of models, continuous learning approaches, and effective real-time visualization.
Structural Analysis and Design of Multi-Storey Symmetric and Asymmetric Shape...IRJET Journal
This document summarizes a research project that aims to compare the structural performance of conventional slab and grid slab systems in multi-story buildings using ETABS software. The study will analyze both symmetric and asymmetric building models under various loading conditions. Parameters like deflections, moments, shears, and stresses will be examined to evaluate the structural effectiveness of each slab type. The results will provide insights into the comparative behavior of conventional and grid slabs to help engineers and architects select appropriate slab systems based on building layouts and design requirements.
A Review of “Seismic Response of RC Structures Having Plan and Vertical Irreg...IRJET Journal
This document summarizes and reviews a research paper on the seismic response of reinforced concrete (RC) structures with plan and vertical irregularities, with and without infill walls. It discusses how infill walls can improve or reduce the seismic performance of RC buildings, depending on factors like wall layout, height distribution, connection to the frame, and relative stiffness of walls and frames. The reviewed research paper analyzes the behavior of infill walls, effects of vertical irregularities, and seismic performance of high-rise structures under linear static and dynamic analysis. It studies response characteristics like story drift, deflection and shear. The document also provides literature on similar research investigating the effects of infill walls, soft stories, plan irregularities, and different
This document provides a review of machine learning techniques used in Advanced Driver Assistance Systems (ADAS). It begins with an abstract that summarizes key applications of machine learning in ADAS, including object detection, recognition, and decision-making. The introduction discusses the integration of machine learning in ADAS and how it is transforming vehicle safety. The literature review then examines several research papers on topics like lightweight deep learning models for object detection and lane detection models using image processing. It concludes by discussing challenges and opportunities in the field, such as improving algorithm robustness and adaptability.
Long Term Trend Analysis of Precipitation and Temperature for Asosa district,...IRJET Journal
The document analyzes temperature and precipitation trends in Asosa District, Benishangul Gumuz Region, Ethiopia from 1993 to 2022 based on data from the local meteorological station. The results show:
1) The average maximum and minimum annual temperatures have generally decreased over time, with maximum temperatures decreasing by a factor of -0.0341 and minimum by -0.0152.
2) Mann-Kendall tests found the decreasing temperature trends to be statistically significant for annual maximum temperatures but not for annual minimum temperatures.
3) Annual precipitation in Asosa District showed a statistically significant increasing trend.
The conclusions recommend development planners account for rising summer precipitation and declining temperatures in
P.E.B. Framed Structure Design and Analysis Using STAAD ProIRJET Journal
This document discusses the design and analysis of pre-engineered building (PEB) framed structures using STAAD Pro software. It provides an overview of PEBs, including that they are designed off-site with building trusses and beams produced in a factory. STAAD Pro is identified as a key tool for modeling, analyzing, and designing PEBs to ensure their performance and safety under various load scenarios. The document outlines modeling structural parts in STAAD Pro, evaluating structural reactions, assigning loads, and following international design codes and standards. In summary, STAAD Pro is used to design and analyze PEB framed structures to ensure safety and code compliance.
A Review on Innovative Fiber Integration for Enhanced Reinforcement of Concre...IRJET Journal
This document provides a review of research on innovative fiber integration methods for reinforcing concrete structures. It discusses studies that have explored using carbon fiber reinforced polymer (CFRP) composites with recycled plastic aggregates to develop more sustainable strengthening techniques. It also examines using ultra-high performance fiber reinforced concrete to improve shear strength in beams. Additional topics covered include the dynamic responses of FRP-strengthened beams under static and impact loads, and the performance of preloaded CFRP-strengthened fiber reinforced concrete beams. The review highlights the potential of fiber composites to enable more sustainable and resilient construction practices.
Survey Paper on Cloud-Based Secured Healthcare SystemIRJET Journal
This document summarizes a survey on securing patient healthcare data in cloud-based systems. It discusses using technologies like facial recognition, smart cards, and cloud computing combined with strong encryption to securely store patient data. The survey found that healthcare professionals believe digitizing patient records and storing them in a centralized cloud system would improve access during emergencies and enable more efficient care compared to paper-based systems. However, ensuring privacy and security of patient data is paramount as healthcare incorporates these digital technologies.
Review on studies and research on widening of existing concrete bridgesIRJET Journal
This document summarizes several studies that have been conducted on widening existing concrete bridges. It describes a study from China that examined load distribution factors for a bridge widened with composite steel-concrete girders. It also outlines challenges and solutions for widening a bridge in the UAE, including replacing bearings and stitching the new and existing structures. Additionally, it discusses two bridge widening projects in New Zealand that involved adding precast beams and stitching to connect structures. Finally, safety measures and challenges for strengthening a historic bridge in Switzerland under live traffic are presented.
React based fullstack edtech web applicationIRJET Journal
The document describes the architecture of an educational technology web application built using the MERN stack. It discusses the frontend developed with ReactJS, backend with NodeJS and ExpressJS, and MongoDB database. The frontend provides dynamic user interfaces, while the backend offers APIs for authentication, course management, and other functions. MongoDB enables flexible data storage. The architecture aims to provide a scalable, responsive platform for online learning.
A Comprehensive Review of Integrating IoT and Blockchain Technologies in the ...IRJET Journal
This paper proposes integrating Internet of Things (IoT) and blockchain technologies to help implement objectives of India's National Education Policy (NEP) in the education sector. The paper discusses how blockchain could be used for secure student data management, credential verification, and decentralized learning platforms. IoT devices could create smart classrooms, automate attendance tracking, and enable real-time monitoring. Blockchain would ensure integrity of exam processes and resource allocation, while smart contracts automate agreements. The paper argues this integration has potential to revolutionize education by making it more secure, transparent and efficient, in alignment with NEP goals. However, challenges like infrastructure needs, data privacy, and collaborative efforts are also discussed.
A REVIEW ON THE PERFORMANCE OF COCONUT FIBRE REINFORCED CONCRETE.IRJET Journal
This document provides a review of research on the performance of coconut fibre reinforced concrete. It summarizes several studies that tested different volume fractions and lengths of coconut fibres in concrete mixtures with varying compressive strengths. The studies found that coconut fibre improved properties like tensile strength, toughness, crack resistance, and spalling resistance compared to plain concrete. Volume fractions of 2-5% and fibre lengths of 20-50mm produced the best results. The document concludes that using a 4-5% volume fraction of coconut fibres 30-40mm in length with M30-M60 grade concrete would provide benefits based on previous research.
Optimizing Business Management Process Workflows: The Dynamic Influence of Mi...IRJET Journal
The document discusses optimizing business management processes through automation using Microsoft Power Automate and artificial intelligence. It provides an overview of Power Automate's key components and features for automating workflows across various apps and services. The document then presents several scenarios applying automation solutions to common business processes like data entry, monitoring, HR, finance, customer support, and more. It estimates the potential time and cost savings from implementing automation for each scenario. Finally, the conclusion emphasizes the transformative impact of AI and automation tools on business processes and the need for ongoing optimization.
Multistoried and Multi Bay Steel Building Frame by using Seismic DesignIRJET Journal
The document describes the seismic design of a G+5 steel building frame located in Roorkee, India according to Indian codes IS 1893-2002 and IS 800. The frame was analyzed using the equivalent static load method and response spectrum method, and its response in terms of displacements and shear forces were compared. Based on the analysis, the frame was designed as a seismic-resistant steel structure according to IS 800:2007. The software STAAD Pro was used for the analysis and design.
Cost Optimization of Construction Using Plastic Waste as a Sustainable Constr...IRJET Journal
This research paper explores using plastic waste as a sustainable and cost-effective construction material. The study focuses on manufacturing pavers and bricks using recycled plastic and partially replacing concrete with plastic alternatives. Initial results found that pavers and bricks made from recycled plastic demonstrate comparable strength and durability to traditional materials while providing environmental and cost benefits. Additionally, preliminary research indicates incorporating plastic waste as a partial concrete replacement significantly reduces construction costs without compromising structural integrity. The outcomes suggest adopting plastic waste in construction can address plastic pollution while optimizing costs, promoting more sustainable building practices.
Optimizing Gradle Builds - Gradle DPE Tour Berlin 2024Sinan KOZAK
Sinan from the Delivery Hero mobile infrastructure engineering team shares a deep dive into performance acceleration with Gradle build cache optimizations. Sinan shares their journey into solving complex build-cache problems that affect Gradle builds. By understanding the challenges and solutions found in our journey, we aim to demonstrate the possibilities for faster builds. The case study reveals how overlapping outputs and cache misconfigurations led to significant increases in build times, especially as the project scaled up with numerous modules using Paparazzi tests. The journey from diagnosing to defeating cache issues offers invaluable lessons on maintaining cache integrity without sacrificing functionality.
Redefining brain tumor segmentation: a cutting-edge convolutional neural netw...IJECEIAES
Medical image analysis has witnessed significant advancements with deep learning techniques. In the domain of brain tumor segmentation, the ability to
precisely delineate tumor boundaries from magnetic resonance imaging (MRI)
scans holds profound implications for diagnosis. This study presents an ensemble convolutional neural network (CNN) with transfer learning, integrating
the state-of-the-art Deeplabv3+ architecture with the ResNet18 backbone. The
model is rigorously trained and evaluated, exhibiting remarkable performance
metrics, including an impressive global accuracy of 99.286%, a high-class accuracy of 82.191%, a mean intersection over union (IoU) of 79.900%, a weighted
IoU of 98.620%, and a Boundary F1 (BF) score of 83.303%. Notably, a detailed comparative analysis with existing methods showcases the superiority of
our proposed model. These findings underscore the model’s competence in precise brain tumor localization, underscoring its potential to revolutionize medical
image analysis and enhance healthcare outcomes. This research paves the way
for future exploration and optimization of advanced CNN models in medical
imaging, emphasizing addressing false positives and resource efficiency.
Batteries -Introduction – Types of Batteries – discharging and charging of battery - characteristics of battery –battery rating- various tests on battery- – Primary battery: silver button cell- Secondary battery :Ni-Cd battery-modern battery: lithium ion battery-maintenance of batteries-choices of batteries for electric vehicle applications.
Fuel Cells: Introduction- importance and classification of fuel cells - description, principle, components, applications of fuel cells: H2-O2 fuel cell, alkaline fuel cell, molten carbonate fuel cell and direct methanol fuel cells.
Software Engineering and Project Management - Introduction, Modeling Concepts...Prakhyath Rai
Introduction, Modeling Concepts and Class Modeling: What is Object orientation? What is OO development? OO Themes; Evidence for usefulness of OO development; OO modeling history. Modeling
as Design technique: Modeling, abstraction, The Three models. Class Modeling: Object and Class Concept, Link and associations concepts, Generalization and Inheritance, A sample class model, Navigation of class models, and UML diagrams
Building the Analysis Models: Requirement Analysis, Analysis Model Approaches, Data modeling Concepts, Object Oriented Analysis, Scenario-Based Modeling, Flow-Oriented Modeling, class Based Modeling, Creating a Behavioral Model.
Introduction- e - waste – definition - sources of e-waste– hazardous substances in e-waste - effects of e-waste on environment and human health- need for e-waste management– e-waste handling rules - waste minimization techniques for managing e-waste – recycling of e-waste - disposal treatment methods of e- waste – mechanism of extraction of precious metal from leaching solution-global Scenario of E-waste – E-waste in India- case studies.
Null Bangalore | Pentesters Approach to AWS IAMDivyanshu
#Abstract:
- Learn more about the real-world methods for auditing AWS IAM (Identity and Access Management) as a pentester. So let us proceed with a brief discussion of IAM as well as some typical misconfigurations and their potential exploits in order to reinforce the understanding of IAM security best practices.
- Gain actionable insights into AWS IAM policies and roles, using hands on approach.
#Prerequisites:
- Basic understanding of AWS services and architecture
- Familiarity with cloud security concepts
- Experience using the AWS Management Console or AWS CLI.
- For hands on lab create account on [killercoda.com](https://killercoda.com/cloudsecurity-scenario/)
# Scenario Covered:
- Basics of IAM in AWS
- Implementing IAM Policies with Least Privilege to Manage S3 Bucket
- Objective: Create an S3 bucket with least privilege IAM policy and validate access.
- Steps:
- Create S3 bucket.
- Attach least privilege policy to IAM user.
- Validate access.
- Exploiting IAM PassRole Misconfiguration
-Allows a user to pass a specific IAM role to an AWS service (ec2), typically used for service access delegation. Then exploit PassRole Misconfiguration granting unauthorized access to sensitive resources.
- Objective: Demonstrate how a PassRole misconfiguration can grant unauthorized access.
- Steps:
- Allow user to pass IAM role to EC2.
- Exploit misconfiguration for unauthorized access.
- Access sensitive resources.
- Exploiting IAM AssumeRole Misconfiguration with Overly Permissive Role
- An overly permissive IAM role configuration can lead to privilege escalation by creating a role with administrative privileges and allow a user to assume this role.
- Objective: Show how overly permissive IAM roles can lead to privilege escalation.
- Steps:
- Create role with administrative privileges.
- Allow user to assume the role.
- Perform administrative actions.
- Differentiation between PassRole vs AssumeRole
Try at [killercoda.com](https://killercoda.com/cloudsecurity-scenario/)