This paper presents the optimization of surface roughness & material removal rate in dry turning of EN-31 steel.Carbide inserts were used for machining of EN-31 to study effects of process parameters [Cutting speed (S), Feed (F) and depth o f cut (d)]. These models can be effectively used to predict the surface roughness (Ra) of the workpiece. The big challenge of the Micro, small& medium industries in India for achieving high quality products with increased productivity.Paper presents work of an investigation of turning process parameters on EN-31 material, for optimization of surface roughness, material removal rate.The experiment is carried out by considering three controllable input variables namely cutting speed, feed rate, and depth of cut.The design of experiment and optimization of surface roughness is carried out by using Taguchi L9 orthogonal array & Grey Relational analysis.
OPTIMIZATION OF TURNING PROCESS PARAMETER IN DRY TURNING OF SAE52100 STEELIAEME Publication
This paper presents the optimization of surface roughness & material removal rate in dry turning of SAE52100 steel. Carbide inserts were used for machining of SAE 52100 to study effects of process parameters [Cutting speed (S), Feed (F) and depth of cut (d)]. These models can be effectively used to predict the surface roughness (Ra) & material removal rate of the workpiece. The big challenge of the Micro, small& medium industries in India for achieving high quality
products with increased productivity.
The big challenge of the mass production firms is concentrated for achieving high quality
products with good dimensionability with high productivity, less wear on the cutting insert, less use
of cutting fluid, within less time. This paper present dissertation work of an investigation of turning
process parameters on hard EN 31 material, for optimization of surface roughness, material removal
rate, machining time in wet and minimum quantity lubrication system. The experiment is carried out
by considering four controllable input variables namely cutting speed, feed rate, depth of cut and
insert nose radius in the presence of wet & MQL system. This experiment also present the relation
between chip formations and controllable variables along with chip thickness, chip colors & chip
velocity from which its effect on insert wear, quality of product can be easily found out, because of
chip morphology gives indirectly the effect of it on the insert wear. In this dissertation work
minimum quantity lubrication system is used for reducing the cutting zone temperature properly and
very fastly. Finally comparison is carried out between wet and minimum quantity lubrication system
from which one can easily identify which system is better for higher productivity along with high
surface finish. This work also present the productivity (MRR) concept in production. The design of
experiment and optimization of surface roughness, material removal rate, machining time is carried
out by using response surface methodology (RSM). Central composite design method is used (CCD)
for the total experimental design work and its analysis and also for optimization of turning process
parameter by which wastage of the machining time, power can be avoided.
optimization of process parameters for cnc turning using taguchi methods for ...INFOGAIN PUBLICATION
Coated and uncoated tool inserts offers certain degrees of control on the desired rate of tool wear and surface roughness to an extent. This work pursues the quest for realizing the optimal values for the significant process parameters that bears an influence on the response parameters. Experiments were conducted on the samples of EN 24 alloy steel material with the help of PVD coated TiAlN insert and uncoated carbide insert. The experimental runs carried out with proper variation in the levels. Levels are selected with the help of manufacturing catalogue and by pilot experimentation and results are recorded for further analysis. For this study, 9 runs designed using L9 orthogonal array of Taguchi Design of Experiment. Surface roughness was measured using a Mitutoyo surface tester at test lab and material removal rate is calculated by mathematical equation. The data was compiled into Minitab 17 software for analysis. The relationship between the machining parameters and the response variables were analyzed using the Taguchi Method. Optimization of process parameters is carried out by Grey Relational Analysis method (GRA). GRA method is a powerful and most versatile tool which can manipulate the input data as per requirement and comes with results that can be used to have best multi-objective in respective concerns
OPTIMIZATION OF TURNING PROCESS PARAMETER IN DRY TURNING OF SAE52100 STEELIAEME Publication
This paper presents the optimization of surface roughness & material removal rate in dry turning of SAE52100 steel. Carbide inserts were used for machining of SAE 52100 to study effects of process parameters [Cutting speed (S), Feed (F) and depth of cut (d)]. These models can be effectively used to predict the surface roughness (Ra) & material removal rate of the workpiece. The big challenge of the Micro, small& medium industries in India for achieving high quality
products with increased productivity.
The big challenge of the mass production firms is concentrated for achieving high quality
products with good dimensionability with high productivity, less wear on the cutting insert, less use
of cutting fluid, within less time. This paper present dissertation work of an investigation of turning
process parameters on hard EN 31 material, for optimization of surface roughness, material removal
rate, machining time in wet and minimum quantity lubrication system. The experiment is carried out
by considering four controllable input variables namely cutting speed, feed rate, depth of cut and
insert nose radius in the presence of wet & MQL system. This experiment also present the relation
between chip formations and controllable variables along with chip thickness, chip colors & chip
velocity from which its effect on insert wear, quality of product can be easily found out, because of
chip morphology gives indirectly the effect of it on the insert wear. In this dissertation work
minimum quantity lubrication system is used for reducing the cutting zone temperature properly and
very fastly. Finally comparison is carried out between wet and minimum quantity lubrication system
from which one can easily identify which system is better for higher productivity along with high
surface finish. This work also present the productivity (MRR) concept in production. The design of
experiment and optimization of surface roughness, material removal rate, machining time is carried
out by using response surface methodology (RSM). Central composite design method is used (CCD)
for the total experimental design work and its analysis and also for optimization of turning process
parameter by which wastage of the machining time, power can be avoided.
optimization of process parameters for cnc turning using taguchi methods for ...INFOGAIN PUBLICATION
Coated and uncoated tool inserts offers certain degrees of control on the desired rate of tool wear and surface roughness to an extent. This work pursues the quest for realizing the optimal values for the significant process parameters that bears an influence on the response parameters. Experiments were conducted on the samples of EN 24 alloy steel material with the help of PVD coated TiAlN insert and uncoated carbide insert. The experimental runs carried out with proper variation in the levels. Levels are selected with the help of manufacturing catalogue and by pilot experimentation and results are recorded for further analysis. For this study, 9 runs designed using L9 orthogonal array of Taguchi Design of Experiment. Surface roughness was measured using a Mitutoyo surface tester at test lab and material removal rate is calculated by mathematical equation. The data was compiled into Minitab 17 software for analysis. The relationship between the machining parameters and the response variables were analyzed using the Taguchi Method. Optimization of process parameters is carried out by Grey Relational Analysis method (GRA). GRA method is a powerful and most versatile tool which can manipulate the input data as per requirement and comes with results that can be used to have best multi-objective in respective concerns
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
COMPARISON OF SURFACE ROUGHNESS OF COLDWORK AND HOT WORK TOOL STEELS IN HARD ...ijmech
The hard turning process has been attracting interest in different industrial sectors for finishing operations
of hard materials at its hardened state.Surface roughness is investigated in hard turning of AISI D3 and
AISI H13 steels of same hardness 62HRC. In this paper, an attempt has been made to model and predict
the surface roughness in hard turning of AISI D3 and AISI H13 hardened steels using Response Surface
Methodology (RSM). The combined effects of three machining parameters such as cutting speed, feed rate
and depth of cut are investigated for main performance characteristic that is surface roughness. RSM
based Central Composite Design (CCD) is applied as an experimental design. Al2O3/TiC mixed ceramic
tool with corner radius 0.8 mm is employed to accomplish 20 tests with six center points. The acceptability
of the developed models is checked using Analysis of Variance (ANOVA).The combined effects of cutting
speed; feed rate and depth of cut are investigated using surface plots.
Optimization of Material Removal Rate & Surface Roughness in Dry Turning of M...IJERA Editor
Optimization of machining parameters is valuable to maintain the accuracy of the components and to minimize
the cost of machining. Surface finish is an important measure for the quality of the machined parts. The present
work is an experimental investigation to study the effect of machining parameters on Material Removal Rate
and Surface Roughness in dry turning of medium carbon steel EN19. Taguchi’s single objective optimization
method was used to find the effect of input parameters on the responses. The experiments were conducted as per
Taguchi’s L9 Orthogonal Array on CNC lathe under dry conditions. Cutting parameters of speed, feed and
depth of cut were taken as inputs and machining was done by PVD TiAlN tool. Regression models for the
responses were prepared by using MINITAB-16 software. Analysis of variance (ANOVA) was used to find the
influence of machining parameters on the responses. From the ANOVA results, it is clear that speed has high
influence followed by feed and depth of cut has very low influence in achieving the optimum values for both
Material Removal Rate and Surface Roughness. Finally, experimental and Regression values of responses were
compared. From the results, it is found that both the values are close to each other hence, the regression models
prepared were more accurate and adequate. Percentage of errors between experimental and regression values
were calculated and they found in the range of ±0.20.
Experimental Investigation and Parametric Studies of Surface Roughness Analy...IJMER
The modern machining industries are focused on achieving high quality, in terms of part/component accuracy, surface finish, high production rate and increase in product life. Surface roughness of machined components has received serious attention of researchers for many years. It has
been an important design feature and quality measure in machining process. There are a large number of
parameters which affect the surface roughness. The typical controllable parameters for the CNC machines
include cutting tool variables, work piece material variables, cutting conditions etc. The desired output is
surface roughness, material removal rate, tool wear, etc. Optimization of machining parameters needs to
determine the most significant parameter for required output. Many techniques are used for optimization
of machining parameters including Taguchi, RSM and ANOVA approach to determine most significant
parameter. The present work is therefore in a direction to integrate effect of various parameters which affect
the surface roughness. This paper investigates the parameters affecting the surface roughness and / or
material removal rate with CNC turning process studied by researchers. It also discusses some other parameters such as cutting force and power consumption in different conditions
“Gray Relational Based Analysis of Al-6351”iosrjce
IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) is a double blind peer reviewed International Journal that provides rapid publication (within a month) of articles in all areas of mechanical and civil engineering and its applications. The journal welcomes publications of high quality papers on theoretical developments and practical applications in mechanical and civil engineering. Original research papers, state-of-the-art reviews, and high quality technical notes are invited for publications.
IJERA (International journal of Engineering Research and Applications) is International online, ... peer reviewed journal. For more detail or submit your article, please visit www.ijera.com
International Journal of Engineering Research and DevelopmentIJERD Editor
Electrical, Electronics and Computer Engineering,
Information Engineering and Technology,
Mechanical, Industrial and Manufacturing Engineering,
Automation and Mechatronics Engineering,
Material and Chemical Engineering,
Civil and Architecture Engineering,
Biotechnology and Bio Engineering,
Environmental Engineering,
Petroleum and Mining Engineering,
Marine and Agriculture engineering,
Aerospace Engineering.
Process Parameter Optimization of Bead geometry for AISI 446 in GMAW Process ...iosrjce
Gas metal arc welding is process is becoming widespread in the welding industries as it can easily
be applied to variety of metals. Quality of weldment depends upon welding input parameters. This experimental
study aims at developing a multi-objective optimization problem to achieve desired weld bead geometry of
GMAW. Objective functions optimized by Taguchi’s L9 orthogonal array design and S/N ratio. Welding
voltage, welding speed, wire feed rate and gas flow rate have been selected as the input process parameters.
Quality targets are bead width, bead height and depth of penetration for AISI 446. The Grey relational analysis
in combination with Taguchi approach is used to solve this multi-objective optimization problem. Additionally
the most significant factor identified by using ANOVA.
OPTIMIZATION OF MACHINING PARAMETERS WITH TOOL INSERT SELECTION FOR S355J2G3 ...AVINASH JURIANI
The key goal of modern manufacturing industries is increased productivity & high quality
Surface Roughness is major concern for quality aspects affecting performance.
Speed, Feed & Depth of cut mainly influences SR & MRR in Turning
Taguchi & Grey Relational Technique is used for optimization followed by ANOVA for contribution
MADM is the need for better Tool Insert Selection to get requisite surface finish
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
COMPARISON OF SURFACE ROUGHNESS OF COLDWORK AND HOT WORK TOOL STEELS IN HARD ...ijmech
The hard turning process has been attracting interest in different industrial sectors for finishing operations
of hard materials at its hardened state.Surface roughness is investigated in hard turning of AISI D3 and
AISI H13 steels of same hardness 62HRC. In this paper, an attempt has been made to model and predict
the surface roughness in hard turning of AISI D3 and AISI H13 hardened steels using Response Surface
Methodology (RSM). The combined effects of three machining parameters such as cutting speed, feed rate
and depth of cut are investigated for main performance characteristic that is surface roughness. RSM
based Central Composite Design (CCD) is applied as an experimental design. Al2O3/TiC mixed ceramic
tool with corner radius 0.8 mm is employed to accomplish 20 tests with six center points. The acceptability
of the developed models is checked using Analysis of Variance (ANOVA).The combined effects of cutting
speed; feed rate and depth of cut are investigated using surface plots.
Optimization of Material Removal Rate & Surface Roughness in Dry Turning of M...IJERA Editor
Optimization of machining parameters is valuable to maintain the accuracy of the components and to minimize
the cost of machining. Surface finish is an important measure for the quality of the machined parts. The present
work is an experimental investigation to study the effect of machining parameters on Material Removal Rate
and Surface Roughness in dry turning of medium carbon steel EN19. Taguchi’s single objective optimization
method was used to find the effect of input parameters on the responses. The experiments were conducted as per
Taguchi’s L9 Orthogonal Array on CNC lathe under dry conditions. Cutting parameters of speed, feed and
depth of cut were taken as inputs and machining was done by PVD TiAlN tool. Regression models for the
responses were prepared by using MINITAB-16 software. Analysis of variance (ANOVA) was used to find the
influence of machining parameters on the responses. From the ANOVA results, it is clear that speed has high
influence followed by feed and depth of cut has very low influence in achieving the optimum values for both
Material Removal Rate and Surface Roughness. Finally, experimental and Regression values of responses were
compared. From the results, it is found that both the values are close to each other hence, the regression models
prepared were more accurate and adequate. Percentage of errors between experimental and regression values
were calculated and they found in the range of ±0.20.
Experimental Investigation and Parametric Studies of Surface Roughness Analy...IJMER
The modern machining industries are focused on achieving high quality, in terms of part/component accuracy, surface finish, high production rate and increase in product life. Surface roughness of machined components has received serious attention of researchers for many years. It has
been an important design feature and quality measure in machining process. There are a large number of
parameters which affect the surface roughness. The typical controllable parameters for the CNC machines
include cutting tool variables, work piece material variables, cutting conditions etc. The desired output is
surface roughness, material removal rate, tool wear, etc. Optimization of machining parameters needs to
determine the most significant parameter for required output. Many techniques are used for optimization
of machining parameters including Taguchi, RSM and ANOVA approach to determine most significant
parameter. The present work is therefore in a direction to integrate effect of various parameters which affect
the surface roughness. This paper investigates the parameters affecting the surface roughness and / or
material removal rate with CNC turning process studied by researchers. It also discusses some other parameters such as cutting force and power consumption in different conditions
“Gray Relational Based Analysis of Al-6351”iosrjce
IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) is a double blind peer reviewed International Journal that provides rapid publication (within a month) of articles in all areas of mechanical and civil engineering and its applications. The journal welcomes publications of high quality papers on theoretical developments and practical applications in mechanical and civil engineering. Original research papers, state-of-the-art reviews, and high quality technical notes are invited for publications.
IJERA (International journal of Engineering Research and Applications) is International online, ... peer reviewed journal. For more detail or submit your article, please visit www.ijera.com
International Journal of Engineering Research and DevelopmentIJERD Editor
Electrical, Electronics and Computer Engineering,
Information Engineering and Technology,
Mechanical, Industrial and Manufacturing Engineering,
Automation and Mechatronics Engineering,
Material and Chemical Engineering,
Civil and Architecture Engineering,
Biotechnology and Bio Engineering,
Environmental Engineering,
Petroleum and Mining Engineering,
Marine and Agriculture engineering,
Aerospace Engineering.
Process Parameter Optimization of Bead geometry for AISI 446 in GMAW Process ...iosrjce
Gas metal arc welding is process is becoming widespread in the welding industries as it can easily
be applied to variety of metals. Quality of weldment depends upon welding input parameters. This experimental
study aims at developing a multi-objective optimization problem to achieve desired weld bead geometry of
GMAW. Objective functions optimized by Taguchi’s L9 orthogonal array design and S/N ratio. Welding
voltage, welding speed, wire feed rate and gas flow rate have been selected as the input process parameters.
Quality targets are bead width, bead height and depth of penetration for AISI 446. The Grey relational analysis
in combination with Taguchi approach is used to solve this multi-objective optimization problem. Additionally
the most significant factor identified by using ANOVA.
OPTIMIZATION OF MACHINING PARAMETERS WITH TOOL INSERT SELECTION FOR S355J2G3 ...AVINASH JURIANI
The key goal of modern manufacturing industries is increased productivity & high quality
Surface Roughness is major concern for quality aspects affecting performance.
Speed, Feed & Depth of cut mainly influences SR & MRR in Turning
Taguchi & Grey Relational Technique is used for optimization followed by ANOVA for contribution
MADM is the need for better Tool Insert Selection to get requisite surface finish
Optimization of hard part turning of bohler K 110 steel with multiple perform...IAEME Publication
Böhler K110 material is used in High-duty cutting tools, blanking and punching tools& small moulds for the plastics industry where excellent wear resistance is required. It is difficult to machine the material in the hardened state (58 HRc).
INVESTIGATION AND OPTIMIZATION OF TURNING PROCESS PARAMETER IN WET AND MQL SY...IAEME Publication
The big challenge of the mass production firms is concentrated for achieving high quality products with good dimensionability with high productivity, less wear on the cutting insert, less use
of cutting fluid, within less time. This paper present dissertation work of an investigation of turning process parameters on hard EN 31 material, for optimization of surface roughness, material removal rate, machining time in wet and minimum quantity lubrication system. The experiment is carried out by considering four controllable input variables namely cutting speed, feed rate, depth of cut and insert nose radius in the presence of wet & MQL system
Experimental Investigation and Parametric Studies of Surface Roughness Analys...IJMER
The modern machining industries are focused on achieving high quality, in terms of
part/component accuracy, surface finish, high production rate and increase in product life. Surface
roughness of machined components has received serious attention of researchers for many years. It has
been an important design feature and quality measure in machining process. There are a large number of
parameters which affect the surface roughness. The typical controllable parameters for the CNC machines
include cutting tool variables, work piece material variables, cutting conditions etc. The desired output is
surface roughness, material removal rate, tool wear, etc. Optimization of machining parameters needs to
determine the most significant parameter for required output. Many techniques are used for optimization
of machining parameters including Taguchi, RSM and ANOVA approach to determine most significant
parameter.
The present work is therefore in a direction to integrate effect of various parameters which affect
the surface roughness. This paper investigates the parameters affecting the surface roughness and / or
material removal rate with CNC turning process studied by researchers. It also discusses some other
parameters such as cutting force and power consumption in different conditions.
Optimization of Metal Removal Rateon Cylindrical Grinding For Is 319 Brass Us...IJERA Editor
Cylindrical grinding is one of the most important metal cutting processes used extensively in the Metal finishing operations. Metal removal rate and surface finish are the important output responses in the production with respect to quantity and quality respectively. The objective of this paper is to arrive at the optimal grinding conditions that will maximize metal removal rate when grinding IS 319 brass. Empirical models were developed using design of experiments by Taguchi L9 Orthogonal Array and the adequacy of the developed model is tested with ANOVA.
Full factorial method for optimization of process parameters for surface roug...Editor IJMTER
Quality and productivity play significant role in today’s manufacturing market.In
machining operations, achieving desired surface quality features of the machined product, is really a
challenging job on cnc machine. Because, these quality features are highly correlated and are
expected to be influenced directly or indirectly by the direct effect of process parameters. There are a
number of parameters like cutting speed, feed and depth of cut etc. which must be given
consideration during the machining of SS 316L. The prediction of optimal machining conditions for
good surface roughness and material removal rate plays a very important role in process planning.
Effect of process factors on surface roughness in dip cryogenic machining of ...eSAT Journals
Abstract A large number of structures that are being constructed at present tend to be wind-sensitive because of their slenderness, shapes, size, lightness and flexibility. With the ever increase in the vertical growth of urban cities, high rise buildings are being constructed in large numbers. In this study, analytical investigation of different shapes of buildings are taken as an example and various analytical approaches are performed on the building. These plans are modeled and wind loads are found out according to I.S 875(part 3)-1987 by taking gust factor and without taking gust factor. These models are compared in different aspects such as storey drift, storey displacement, storey shear, etc. for different shapes of buildings by using finite element software package ETAB’s 13.1.1v. Among these results, which shape of building provide sound wind loading to the structure as well as the structural efficiency would be selected. Key Words: Storey displacement, Storey drift, Storey shear, Gust, Wind load
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Effectiveness of multilayer coated tool in turning of aisi 430 f steeleSAT Journals
Abstract This paper presents minimization of surface roughness in dry turning of AISI 430F steel using TiN-TiCN-Al2O3-ZrCN multilayer coated cemented carbide & cryo-treated inserts. Effect of cutting velocity, feed rate, depth of cut & machining duration is studied on the surface roughness. Taguchi’s design of experiment is used to find the optimum factor levels. It is found that the feed rate has much effect in producing lower surface roughness followed by speed. The depth of cut has lesser role on surface roughness. The result of Taguchi method shows that cutting velocity of 250m/min, feed rate of 0.25 mm/rev and depth of cut of 0.3mm should be maintained as optimal parameter settings for both coated and cryo-treated tools. Cryo-treated tools perform better. Keywords: Cryo-treatment, Dry Turning, Surface roughness, Taguchi Method
Effects of Cutting Tool Parameters on Surface Roughnessirjes
This paper presents of the influence on surface roughness of Co28Cr6Mo medical alloy machined
on a CNC lathe based on cutting parameters (rotational speed, feed rate, depth of cut and nose radius).The
influences of cutting parameters have been presented in graphical form for understanding. To achieve the
minimum surface roughness, the optimum values obtained for rpm, feed rate, depth of cut and nose radius were
respectively, 318 rpm, 0,1 mm/rev, 0,7 mm and 0,8 mm. Maximum surface roughness has been revealed the
values obtained for rpm, feed rate, depth of cut and nose radius were respectively, 318 rpm, 0,25 mm/rev, 0,9
mm and 0,4 mm.
Similar to ANALYSIS OF PROCESS PARAMETERS IN DRY MACHINING OF EN-31 STEEL by GREY RELATIONAL ANALYSIS (20)
Submission Deadline: 30th September 2022
Acceptance Notification: Within Three Days’ time period
Online Publication: Within 24 Hrs. time Period
Expected Date of Dispatch of Printed Journal: 5th October 2022
MODELING AND ANALYSIS OF SURFACE ROUGHNESS AND WHITE LATER THICKNESS IN WIRE-...IAEME Publication
White layer thickness (WLT) formed and surface roughness in wire electric discharge turning (WEDT) of tungsten carbide composite has been made to model through response surface methodology (RSM). A Taguchi’s standard Design of experiments involving five input variables with three levels has been employed to establish a mathematical model between input parameters and responses. Percentage of cobalt content, spindle speed, Pulse on-time, wire feed and pulse off-time were changed during the experimental tests based on the Taguchi’s orthogonal array L27 (3^13). Analysis of variance (ANOVA) revealed that the mathematical models obtained can adequately describe performance within the parameters of the factors considered. There was a good agreement between the experimental and predicted values in this study.
A STUDY ON THE REASONS FOR TRANSGENDER TO BECOME ENTREPRENEURSIAEME Publication
The study explores the reasons for a transgender to become entrepreneurs. In this study transgender entrepreneur was taken as independent variable and reasons to become as dependent variable. Data were collected through a structured questionnaire containing a five point Likert Scale. The study examined the data of 30 transgender entrepreneurs in Salem Municipal Corporation of Tamil Nadu State, India. Simple Random sampling technique was used. Garrett Ranking Technique (Percentile Position, Mean Scores) was used as the analysis for the present study to identify the top 13 stimulus factors for establishment of trans entrepreneurial venture. Economic advancement of a nation is governed upon the upshot of a resolute entrepreneurial doings. The conception of entrepreneurship has stretched and materialized to the socially deflated uncharted sections of transgender community. Presently transgenders have smashed their stereotypes and are making recent headlines of achievements in various fields of our Indian society. The trans-community is gradually being observed in a new light and has been trying to achieve prospective growth in entrepreneurship. The findings of the research revealed that the optimistic changes are taking place to change affirmative societal outlook of the transgender for entrepreneurial ventureship. It also laid emphasis on other transgenders to renovate their traditional living. The paper also highlights that legislators, supervisory body should endorse an impartial canons and reforms in Tamil Nadu Transgender Welfare Board Association.
BROAD UNEXPOSED SKILLS OF TRANSGENDER ENTREPRENEURSIAEME Publication
Since ages gender difference is always a debatable theme whether caused by nature, evolution or environment. The birth of a transgender is dreadful not only for the child but also for their parents. The pain of living in the wrong physique and treated as second class victimized citizen is outrageous and fully harboured with vicious baseless negative scruples. For so long, social exclusion had perpetuated inequality and deprivation experiencing ingrained malign stigma and besieged victims of crime or violence across their life spans. They are pushed into the murky way of life with a source of eternal disgust, bereft sexual potency and perennial fear. Although they are highly visible but very little is known about them. The common public needs to comprehend the ravaged arrogance on these insensitive souls and assist in integrating them into the mainstream by offering equal opportunity, treat with humanity and respect their dignity. Entrepreneurship in the current age is endorsing the gender fairness movement. Unstable careers and economic inadequacy had inclined one of the gender variant people called Transgender to become entrepreneurs. These tiny budding entrepreneurs resulted in economic transition by means of employment, free from the clutches of stereotype jobs, raised standard of living and handful of financial empowerment. Besides all these inhibitions, they were able to witness a platform for skill set development that ignited them to enter into entrepreneurial domain. This paper epitomizes skill sets involved in trans-entrepreneurs of Thoothukudi Municipal Corporation of Tamil Nadu State and is a groundbreaking determination to sightsee various skills incorporated and the impact on entrepreneurship.
DETERMINANTS AFFECTING THE USER'S INTENTION TO USE MOBILE BANKING APPLICATIONSIAEME Publication
The banking and financial services industries are experiencing increased technology penetration. Among them, the banking industry has made technological advancements to better serve the general populace. The economy focused on transforming the banking sector's system into a cashless, paperless, and faceless one. The researcher wants to evaluate the user's intention for utilising a mobile banking application. The study also examines the variables affecting the user's behaviour intention when selecting specific applications for financial transactions. The researcher employed a well-structured questionnaire and a descriptive study methodology to gather the respondents' primary data utilising the snowball sampling technique. The study includes variables like performance expectations, effort expectations, social impact, enabling circumstances, and perceived risk. Each of the aforementioned variables has a major impact on how users utilise mobile banking applications. The outcome will assist the service provider in comprehending the user's history with mobile banking applications.
ANALYSE THE USER PREDILECTION ON GPAY AND PHONEPE FOR DIGITAL TRANSACTIONSIAEME Publication
Technology upgradation in banking sector took the economy to view that payment mode towards online transactions using mobile applications. This system enabled connectivity between banks, Merchant and user in a convenient mode. there are various applications used for online transactions such as Google pay, Paytm, freecharge, mobikiwi, oxygen, phonepe and so on and it also includes mobile banking applications. The study aimed at evaluating the predilection of the user in adopting digital transaction. The study is descriptive in nature. The researcher used random sample techniques to collect the data. The findings reveal that mobile applications differ with the quality of service rendered by Gpay and Phonepe. The researcher suggest the Phonepe application should focus on implementing the application should be user friendly interface and Gpay on motivating the users to feel the importance of request for money and modes of payments in the application.
VOICE BASED ATM FOR VISUALLY IMPAIRED USING ARDUINOIAEME Publication
The prototype of a voice-based ATM for visually impaired using Arduino is to help people who are blind. This uses RFID cards which contain users fingerprint encrypted on it and interacts with the users through voice commands. ATM operates when sensor detects the presence of one person in the cabin. After scanning the RFID card, it will ask to select the mode like –normal or blind. User can select the respective mode through voice input, if blind mode is selected the balance check or cash withdraw can be done through voice input. Normal mode procedure is same as the existing ATM.
IMPACT OF EMOTIONAL INTELLIGENCE ON HUMAN RESOURCE MANAGEMENT PRACTICES AMONG...IAEME Publication
There is increasing acceptability of emotional intelligence as a major factor in personality assessment and effective human resource management. Emotional intelligence as the ability to build capacity, empathize, co-operate, motivate and develop others cannot be divorced from both effective performance and human resource management systems. The human person is crucial in defining organizational leadership and fortunes in terms of challenges and opportunities and walking across both multinational and bilateral relationships. The growing complexity of the business world requires a great deal of self-confidence, integrity, communication, conflict and diversity management to keep the global enterprise within the paths of productivity and sustainability. Using the exploratory research design and 255 participants the result of this original study indicates strong positive correlation between emotional intelligence and effective human resource management. The paper offers suggestions on further studies between emotional intelligence and human capital development and recommends for conflict management as an integral part of effective human resource management.
VISUALISING AGING PARENTS & THEIR CLOSE CARERS LIFE JOURNEY IN AGING ECONOMYIAEME Publication
Our life journey, in general, is closely defined by the way we understand the meaning of why we coexist and deal with its challenges. As we develop the "inspiration economy", we could say that nearly all of the challenges we have faced are opportunities that help us to discover the rest of our journey. In this note paper, we explore how being faced with the opportunity of being a close carer for an aging parent with dementia brought intangible discoveries that changed our insight of the meaning of the rest of our life journey.
A STUDY ON THE IMPACT OF ORGANIZATIONAL CULTURE ON THE EFFECTIVENESS OF PERFO...IAEME Publication
The main objective of this study is to analyze the impact of aspects of Organizational Culture on the Effectiveness of the Performance Management System (PMS) in the Health Care Organization at Thanjavur. Organizational Culture and PMS play a crucial role in present-day organizations in achieving their objectives. PMS needs employees’ cooperation to achieve its intended objectives. Employees' cooperation depends upon the organization’s culture. The present study uses exploratory research to examine the relationship between the Organization's culture and the Effectiveness of the Performance Management System. The study uses a Structured Questionnaire to collect the primary data. For this study, Thirty-six non-clinical employees were selected from twelve randomly selected Health Care organizations at Thanjavur. Thirty-two fully completed questionnaires were received.
Living in 21st century in itself reminds all of us the necessity of police and its administration. As more and more we are entering into the modern society and culture, the more we require the services of the so called ‘Khaki Worthy’ men i.e., the police personnel. Whether we talk of Indian police or the other nation’s police, they all have the same recognition as they have in India. But as already mentioned, their services and requirements are different after the like 26th November, 2008 incidents, where they without saving their own lives has sacrificed themselves without any hitch and without caring about their respective family members and wards. In other words, they are like our heroes and mentors who can guide us from the darkness of fear, militancy, corruption and other dark sides of life and so on. Now the question arises, if Gandhi would have been alive today, what would have been his reaction/opinion to the police and its functioning? Would he have some thing different in his mind now what he had been in his mind before the partition or would he be going to start some Satyagraha in the form of some improvement in the functioning of the police administration? Really these questions or rather night mares can come to any one’s mind, when there is too much confusion is prevailing in our minds, when there is too much corruption in the society and when the polices working is also in the questioning because of one or the other case throughout the India. It is matter of great concern that we have to thing over our administration and our practical approach because the police personals are also like us, they are part and parcel of our society and among one of us, so why we all are pin pointing towards them.
A STUDY ON TALENT MANAGEMENT AND ITS IMPACT ON EMPLOYEE RETENTION IN SELECTED...IAEME Publication
The goal of this study was to see how talent management affected employee retention in the selected IT organizations in Chennai. The fundamental issue was the difficulty to attract, hire, and retain talented personnel who perform well and the gap between supply and demand of talent acquisition and retaining them within the firms. The study's main goals were to determine the impact of talent management on employee retention in IT companies in Chennai, investigate talent management strategies that IT companies could use to improve talent acquisition, performance management, career planning and formulate retention strategies that the IT firms could use. The respondents were given a structured close-ended questionnaire with the 5 Point Likert Scale as part of the study's quantitative research design. The target population consisted of 289 IT professionals. The questionnaires were distributed and collected by the researcher directly. The Statistical Package for Social Sciences (SPSS) was used to collect and analyse the questionnaire responses. Hypotheses that were formulated for the various areas of the study were tested using a variety of statistical tests. The key findings of the study suggested that talent management had an impact on employee retention. The studies also found that there is a clear link between the implementation of talent management and retention measures. Management should provide enough training and development for employees, clarify job responsibilities, provide adequate remuneration packages, and recognise employees for exceptional performance.
ATTRITION IN THE IT INDUSTRY DURING COVID-19 PANDEMIC: LINKING EMOTIONAL INTE...IAEME Publication
Globally, Millions of dollars were spent by the organizations for employing skilled Information Technology (IT) professionals. It is costly to replace unskilled employees with IT professionals possessing technical skills and competencies that aid in interconnecting the business processes. The organization’s employment tactics were forced to alter by globalization along with technological innovations as they consistently diminish to remain lean, outsource to concentrate on core competencies along with restructuring/reallocate personnel to gather efficiency. As other jobs, organizations or professions have become reasonably more appropriate in a shifting employment landscape, the above alterations trigger both involuntary as well as voluntary turnover. The employee view on jobs is also afflicted by the COVID-19 pandemic along with the employee-driven labour market. So, having effective strategies is necessary to tackle the withdrawal rate of employees. By associating Emotional Intelligence (EI) along with Talent Management (TM) in the IT industry, the rise in attrition rate was analyzed in this study. Only 303 respondents were collected out of 350 participants to whom questionnaires were distributed. From the employees of IT organizations located in Bangalore (India), the data were congregated. A simple random sampling methodology was employed to congregate data as of the respondents. Generating the hypothesis along with testing is eventuated. The effect of EI and TM along with regression analysis between TM and EI was analyzed. The outcomes indicated that employee and Organizational Performance (OP) were elevated by effective EI along with TM.
INFLUENCE OF TALENT MANAGEMENT PRACTICES ON ORGANIZATIONAL PERFORMANCE A STUD...IAEME Publication
By implementing talent management strategy, organizations would have the option to retain their skilled professionals while additionally working on their overall performance. It is the course of appropriately utilizing the ideal individuals, setting them up for future top positions, exploring and dealing with their performance, and holding them back from leaving the organization. It is employee performance that determines the success of every organization. The firm quickly obtains an upper hand over its rivals in the event that its employees having particular skills that cannot be duplicated by the competitors. Thus, firms are centred on creating successful talent management practices and processes to deal with the unique human resources. Firms are additionally endeavouring to keep their top/key staff since on the off chance that they leave; the whole store of information leaves the firm's hands. The study's objective was to determine the impact of talent management on organizational performance among the selected IT organizations in Chennai. The study recommends that talent management limitedly affects performance. On the off chance that this talent is appropriately management and implemented properly, organizations might benefit as much as possible from their maintained assets to support development and productivity, both monetarily and non-monetarily.
A STUDY OF VARIOUS TYPES OF LOANS OF SELECTED PUBLIC AND PRIVATE SECTOR BANKS...IAEME Publication
Banking regulations act of India, 1949 defines banking as “acceptance of deposits for the purpose of lending or investment from the public, repayment on demand or otherwise and withdrawable through cheques, drafts order or otherwise”, the major participants of the Indian financial system are commercial banks, the financial institution encompassing term lending institutions. Investments institutions, specialized financial institution and the state level development banks, non banking financial companies (NBFC) and other market intermediaries such has the stock brokers and money lenders are among the oldest of the certain variants of NBFC and the oldest market participants. The asset quality of banks is one of the most important indicators of their financial health. The Indian banking sector has been facing severe problems of increasing Non- Performing Assets (NPAs). The NPAs growth directly and indirectly affects the quality of assets and profitability of banks. It also shows the efficiency of banks credit risk management and the recovery effectiveness. NPA do not generate any income, whereas, the bank is required to make provisions for such as assets that why is a double edge weapon. This paper outlines the concept of quality of bank loans of different types like Housing, Agriculture and MSME loans in state Haryana of selected public and private sector banks. This study is highlighting problems associated with the role of commercial bank in financing Small and Medium Scale Enterprises (SME). The overall objective of the research was to assess the effect of the financing provisions existing for the setting up and operations of MSMEs in the country and to generate recommendations for more robust financing mechanisms for successful operation of the MSMEs, in turn understanding the impact of MSME loans on financial institutions due to NPA. There are many research conducted on the topic of Non- Performing Assets (NPA) Management, concerning particular bank, comparative study of public and private banks etc. In this paper the researcher is considering the aggregate data of selected public sector and private sector banks and attempts to compare the NPA of Housing, Agriculture and MSME loans in state Haryana of public and private sector banks. The tools used in the study are average and Anova test and variance. The findings reveal that NPA is common problem for both public and private sector banks and is associated with all types of loans either that is housing loans, agriculture loans and loans to SMES. NPAs of both public and private sector banks show the increasing trend. In 2010-11 GNPA of public and private sector were at same level it was 2% but after 2010-11 it increased in many fold and at present there is GNPA in some more than 15%. It shows the dark area of Indian banking sector.
EXPERIMENTAL STUDY OF MECHANICAL AND TRIBOLOGICAL RELATION OF NYLON/BaSO4 POL...IAEME Publication
An experiment conducted in this study found that BaSO4 changed Nylon 6's mechanical properties. By changing the weight ratios, BaSO4 was used to make Nylon 6. This Researcher looked into how hard Nylon-6/BaSO4 composites are and how well they wear. Experiments were done based on Taguchi design L9. Nylon-6/BaSO4 composites can be tested for their hardness number using a Rockwell hardness testing apparatus. On Nylon/BaSO4, the wear behavior was measured by a wear monitor, pinon-disc friction by varying reinforcement, sliding speed, and sliding distance, and the microstructure of the crack surfaces was observed by SEM. This study provides significant contributions to ultimate strength by increasing BaSO4 content up to 16% in the composites, and sliding speed contributes 72.45% to the wear rate
ROLE OF SOCIAL ENTREPRENEURSHIP IN RURAL DEVELOPMENT OF INDIA - PROBLEMS AND ...IAEME Publication
The majority of the population in India lives in villages. The village is the back bone of the country. Village or rural industries play an important role in the national economy, particularly in the rural development. Developing the rural economy is one of the key indicators towards a country’s success. Whether it be the need to look after the welfare of the farmers or invest in rural infrastructure, Governments have to ensure that rural development isn’t compromised. The economic development of our country largely depends on the progress of rural areas and the standard of living of rural masses. Village or rural industries play an important role in the national economy, particularly in the rural development. Rural entrepreneurship is based on stimulating local entrepreneurial talent and the subsequent growth of indigenous enterprises. It recognizes opportunity in the rural areas and accelerates a unique blend of resources either inside or outside of agriculture. Rural entrepreneurship brings an economic value to the rural sector by creating new methods of production, new markets, new products and generate employment opportunities thereby ensuring continuous rural development. Social Entrepreneurship has the direct and primary objective of serving the society along with the earning profits. So, social entrepreneurship is different from the economic entrepreneurship as its basic objective is not to earn profits but for providing innovative solutions to meet the society needs which are not taken care by majority of the entrepreneurs as they are in the business for profit making as a sole objective. So, the Social Entrepreneurs have the huge growth potential particularly in the developing countries like India where we have huge societal disparities in terms of the financial positions of the population. Still 22 percent of the Indian population is below the poverty line and also there is disparity among the rural & urban population in terms of families living under BPL. 25.7 percent of the rural population & 13.7 percent of the urban population is under BPL which clearly shows the disparity of the poor people in the rural and urban areas. The need to develop social entrepreneurship in agriculture is dictated by a large number of social problems. Such problems include low living standards, unemployment, and social tension. The reasons that led to the emergence of the practice of social entrepreneurship are the above factors. The research problem lays upon disclosing the importance of role of social entrepreneurship in rural development of India. The paper the tendencies of social entrepreneurship in India, to present successful examples of such business for providing recommendations how to improve situation in rural areas in terms of social entrepreneurship development. Indian government has made some steps towards development of social enterprises, social entrepreneurship, and social in- novation, but a lot remains to be improved.
OPTIMAL RECONFIGURATION OF POWER DISTRIBUTION RADIAL NETWORK USING HYBRID MET...IAEME Publication
Distribution system is a critical link between the electric power distributor and the consumers. Most of the distribution networks commonly used by the electric utility is the radial distribution network. However in this type of network, it has technical issues such as enormous power losses which affect the quality of the supply. Nowadays, the introduction of Distributed Generation (DG) units in the system help improve and support the voltage profile of the network as well as the performance of the system components through power loss mitigation. In this study network reconfiguration was done using two meta-heuristic algorithms Particle Swarm Optimization and Gravitational Search Algorithm (PSO-GSA) to enhance power quality and voltage profile in the system when simultaneously applied with the DG units. Backward/Forward Sweep Method was used in the load flow analysis and simulated using the MATLAB program. Five cases were considered in the Reconfiguration based on the contribution of DG units. The proposed method was tested using IEEE 33 bus system. Based on the results, there was a voltage profile improvement in the system from 0.9038 p.u. to 0.9594 p.u.. The integration of DG in the network also reduced power losses from 210.98 kW to 69.3963 kW. Simulated results are drawn to show the performance of each case.
APPLICATION OF FRUGAL APPROACH FOR PRODUCTIVITY IMPROVEMENT - A CASE STUDY OF...IAEME Publication
Manufacturing industries have witnessed an outburst in productivity. For productivity improvement manufacturing industries are taking various initiatives by using lean tools and techniques. However, in different manufacturing industries, frugal approach is applied in product design and services as a tool for improvement. Frugal approach contributed to prove less is more and seems indirectly contributing to improve productivity. Hence, there is need to understand status of frugal approach application in manufacturing industries. All manufacturing industries are trying hard and putting continuous efforts for competitive existence. For productivity improvements, manufacturing industries are coming up with different effective and efficient solutions in manufacturing processes and operations. To overcome current challenges, manufacturing industries have started using frugal approach in product design and services. For this study, methodology adopted with both primary and secondary sources of data. For primary source interview and observation technique is used and for secondary source review has done based on available literatures in website, printed magazines, manual etc. An attempt has made for understanding application of frugal approach with the study of manufacturing industry project. Manufacturing industry selected for this project study is Mahindra and Mahindra Ltd. This paper will help researcher to find the connections between the two concepts productivity improvement and frugal approach. This paper will help to understand significance of frugal approach for productivity improvement in manufacturing industry. This will also help to understand current scenario of frugal approach in manufacturing industry. In manufacturing industries various process are involved to deliver the final product. In the process of converting input in to output through manufacturing process productivity plays very critical role. Hence this study will help to evolve status of frugal approach in productivity improvement programme. The notion of frugal can be viewed as an approach towards productivity improvement in manufacturing industries.
A MULTIPLE – CHANNEL QUEUING MODELS ON FUZZY ENVIRONMENTIAEME Publication
In this paper, we investigated a queuing model of fuzzy environment-based a multiple channel queuing model (M/M/C) ( /FCFS) and study its performance under realistic conditions. It applies a nonagonal fuzzy number to analyse the relevant performance of a multiple channel queuing model (M/M/C) ( /FCFS). Based on the sub interval average ranking method for nonagonal fuzzy number, we convert fuzzy number to crisp one. Numerical results reveal that the efficiency of this method. Intuitively, the fuzzy environment adapts well to a multiple channel queuing models (M/M/C) ( /FCFS) are very well.
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Forklift Classes Overview by Intella PartsIntella Parts
Discover the different forklift classes and their specific applications. Learn how to choose the right forklift for your needs to ensure safety, efficiency, and compliance in your operations.
For more technical information, visit our website https://intellaparts.com
Democratizing Fuzzing at Scale by Abhishek Aryaabh.arya
Presented at NUS: Fuzzing and Software Security Summer School 2024
This keynote talks about the democratization of fuzzing at scale, highlighting the collaboration between open source communities, academia, and industry to advance the field of fuzzing. It delves into the history of fuzzing, the development of scalable fuzzing platforms, and the empowerment of community-driven research. The talk will further discuss recent advancements leveraging AI/ML and offer insights into the future evolution of the fuzzing landscape.
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
Event Management System Vb Net Project Report.pdfKamal Acharya
In present era, the scopes of information technology growing with a very fast .We do not see any are untouched from this industry. The scope of information technology has become wider includes: Business and industry. Household Business, Communication, Education, Entertainment, Science, Medicine, Engineering, Distance Learning, Weather Forecasting. Carrier Searching and so on.
My project named “Event Management System” is software that store and maintained all events coordinated in college. It also helpful to print related reports. My project will help to record the events coordinated by faculties with their Name, Event subject, date & details in an efficient & effective ways.
In my system we have to make a system by which a user can record all events coordinated by a particular faculty. In our proposed system some more featured are added which differs it from the existing system such as security.
Courier management system project report.pdfKamal Acharya
It is now-a-days very important for the people to send or receive articles like imported furniture, electronic items, gifts, business goods and the like. People depend vastly on different transport systems which mostly use the manual way of receiving and delivering the articles. There is no way to track the articles till they are received and there is no way to let the customer know what happened in transit, once he booked some articles. In such a situation, we need a system which completely computerizes the cargo activities including time to time tracking of the articles sent. This need is fulfilled by Courier Management System software which is online software for the cargo management people that enables them to receive the goods from a source and send them to a required destination and track their status from time to time.
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.