Design and Analysis of Microstrip Antenna for CDMA Systems CommunicationIOSR Journals
This paper proposes a newly designed microstrip patch antennas (MSA) for wireless application
(CDMA Systems). The designed single antenna E-shaped patch antenna. Two parallel slots are in corporated
into the patch of a microstrip antenna to expand it bandwidth, and designed antenna operates in the frequency
range of 1.85 to 1.99 GHz. The antenna is designed using air as a dielectric substrate between the ground plane
and substrate patch antenna. IE3D is a full-wave electromagnetic simulator based on the method of moments
(MoM) technique. It has been widely used in the design of MICs, RFICs, patch antennas, wire antennas, and
other RF/wireless antennas. It can be used to calculate and plot the S parameters, VSWR, current distributions
as well as the radiation patterns. The results obtained for each patch were 2D and 3D view of patch, Directivity,
Gain, beam width and other such parameters, true and mapped 3D radiation pattern, and 2D polar radiation
pattern. The antenna successfully achieves the exhibit a broad impedance bandwidth of 27 % (at VSWR < 2)
with respect to the center frequency of 1.9 GHz is designed, fabricated, and finally measured on Spectrum
analyzer. The radiation pattern and directivity are also presented.. Gain maximum achievable is 3 dBi and good
return loss (S11 parameters) of -30 dB is achieved along with broadside radiation pattern.
Microstrip patch antenna with metamaterial using superstrate technique for wi...journalBEEI
This work builds a metamaterial (MTM) superstrate loaded on a patch of microstrip antenna for wireless communications. The MTM superstrate is made up of four G-shaped resonators on FR-4 substrate with a relative permittivity of 4.4 and has a total area of (8×16) mm2, and is higher than the patch. The MTM superstrate increases antenna gain while also raising the input reflection coefficient. When it is 9 mm above the patch, the gain increased from 3.28 dB to 6.02 dB, and when it is 7 mm above the patch, the input reflection coefficient was enhanced from -31.217 dB to -45.8 dB. When the MTM superstrate loaded antenna was compared to the traditional unloaded antenna, it was discovered that metamaterials have a lot of potential for improving antenna performance.
Analysis of Metamaterial Based Microstrip Array Antennaijceronline
Metamaterials have been intensively researched due to their peculiar features such as negative permittivity and/or permeability and ultra-refraction phenomenon. To satisfy the demand of commonly used wireless communication systems, an antenna which can operate at higher frequencies and enhanced characteristics are desirable. The arrangement of all elements is done that they provide an improvement in bandwidth, directivity return loss etc. The frequency response of a metamaterial can be tailored by varying its characteristics. A new metamaterial structure using square and ring split ring resonator is proposed. Using this metamaterial structure, a microstrip patch antenna is designed with enhanced characteristics such as reduction in return lossfrom-20dB to -36dB with tunability is achieved.
Antenna array design with rectangular ring slot for 5G technologyTELKOMNIKA JOURNAL
A patch antenna with rectangular-shaped ring slot that fed by a coaxial probe is proposed in this
article as the single element for planar patch array antenna design to meet the requirement of multiple
input multiple output (MIMO) in fifth generation (5G) technology. Initially, the single antenna element is
designed at three different center frequencies of 0.85, 1.9 and 2.6 GHz to cover the mobile operating
frequency of 0.8, 0.85, 0.9, 1.8, 2.1 and 2.6 GHz, which considering the proposed 5G spectrum below than
6 GHz. The rectangular-shaped ring slot is introduced to the patch antenna with the partial ground plane to
widen the bandwidth performance. The designed single element is then arranged to design planar arrays
of 2x2. Each of elements in the planar array is fed by a coaxial probe. The designs are utilizing a
high-performance substrate, Rogers 6010LM.
A Compact Multiband Metamaterial based Microstrip Patch Antenna for Wireless ...IJERA Editor
In this paper, a metamaterial based compact multiband microstrip antenna is proposed which can give high gain and directivity. Metamaterials are periodic structures and have been intensively investigated due to the particular features such as ultra-refraction phenomenon and negative permittivity and/or permeability. A metamaterialbased microstrip patch antenna with enhanced characteristics and multi band operation will be investigated in this work. The multiple frequency operation will be achieved by varying the capacitance of the metamaterial structure with the help of metallic loadings placed in each metamaterial unit cells. The potential impacts will be miniaturization, reduced cost and reduced power consumption since multiple antennas operating at different frequencies are replaced by a single antenna which can operate at multiple frequencies. The proposed microstrip patch antenna will have its frequencies of operation in the L, S and C bands. The proposed structure is simulated using Agilent Advanced Design System (ADS) 2011.05. It is then fabricated on the FR4 substrate and the performance of the fabricated antenna is measured using the Vector Network Analyzer (VNA)
Gain Enhancement of Series Feed Square Patch Microstrip Antenna Array for S b...ijsrd.com
Gain is the ability of an antenna to concentrate the radiated power in a desired direction. Only small gain can be achieved by single antenna that is why, antenna arrays are required to improve the gain by using different feed networks. This paper describes the design and performance of a series feed antenna array. The operating frequency of 2.4GHz is used. The aim of this paper is to improve the gain of a series feed antenna array. Line feed is used for designing single antenna, 2x1 & 4x1 microstrip antenna array. These series feed microstrip antenna arrays are useful for both S and C band. The proposed antenna is simulated by IE3D version 9.0 Zealand simulation software based on method of moments.
Design and Analysis of Microstrip Antenna for CDMA Systems CommunicationIOSR Journals
This paper proposes a newly designed microstrip patch antennas (MSA) for wireless application
(CDMA Systems). The designed single antenna E-shaped patch antenna. Two parallel slots are in corporated
into the patch of a microstrip antenna to expand it bandwidth, and designed antenna operates in the frequency
range of 1.85 to 1.99 GHz. The antenna is designed using air as a dielectric substrate between the ground plane
and substrate patch antenna. IE3D is a full-wave electromagnetic simulator based on the method of moments
(MoM) technique. It has been widely used in the design of MICs, RFICs, patch antennas, wire antennas, and
other RF/wireless antennas. It can be used to calculate and plot the S parameters, VSWR, current distributions
as well as the radiation patterns. The results obtained for each patch were 2D and 3D view of patch, Directivity,
Gain, beam width and other such parameters, true and mapped 3D radiation pattern, and 2D polar radiation
pattern. The antenna successfully achieves the exhibit a broad impedance bandwidth of 27 % (at VSWR < 2)
with respect to the center frequency of 1.9 GHz is designed, fabricated, and finally measured on Spectrum
analyzer. The radiation pattern and directivity are also presented.. Gain maximum achievable is 3 dBi and good
return loss (S11 parameters) of -30 dB is achieved along with broadside radiation pattern.
Microstrip patch antenna with metamaterial using superstrate technique for wi...journalBEEI
This work builds a metamaterial (MTM) superstrate loaded on a patch of microstrip antenna for wireless communications. The MTM superstrate is made up of four G-shaped resonators on FR-4 substrate with a relative permittivity of 4.4 and has a total area of (8×16) mm2, and is higher than the patch. The MTM superstrate increases antenna gain while also raising the input reflection coefficient. When it is 9 mm above the patch, the gain increased from 3.28 dB to 6.02 dB, and when it is 7 mm above the patch, the input reflection coefficient was enhanced from -31.217 dB to -45.8 dB. When the MTM superstrate loaded antenna was compared to the traditional unloaded antenna, it was discovered that metamaterials have a lot of potential for improving antenna performance.
Analysis of Metamaterial Based Microstrip Array Antennaijceronline
Metamaterials have been intensively researched due to their peculiar features such as negative permittivity and/or permeability and ultra-refraction phenomenon. To satisfy the demand of commonly used wireless communication systems, an antenna which can operate at higher frequencies and enhanced characteristics are desirable. The arrangement of all elements is done that they provide an improvement in bandwidth, directivity return loss etc. The frequency response of a metamaterial can be tailored by varying its characteristics. A new metamaterial structure using square and ring split ring resonator is proposed. Using this metamaterial structure, a microstrip patch antenna is designed with enhanced characteristics such as reduction in return lossfrom-20dB to -36dB with tunability is achieved.
Antenna array design with rectangular ring slot for 5G technologyTELKOMNIKA JOURNAL
A patch antenna with rectangular-shaped ring slot that fed by a coaxial probe is proposed in this
article as the single element for planar patch array antenna design to meet the requirement of multiple
input multiple output (MIMO) in fifth generation (5G) technology. Initially, the single antenna element is
designed at three different center frequencies of 0.85, 1.9 and 2.6 GHz to cover the mobile operating
frequency of 0.8, 0.85, 0.9, 1.8, 2.1 and 2.6 GHz, which considering the proposed 5G spectrum below than
6 GHz. The rectangular-shaped ring slot is introduced to the patch antenna with the partial ground plane to
widen the bandwidth performance. The designed single element is then arranged to design planar arrays
of 2x2. Each of elements in the planar array is fed by a coaxial probe. The designs are utilizing a
high-performance substrate, Rogers 6010LM.
A Compact Multiband Metamaterial based Microstrip Patch Antenna for Wireless ...IJERA Editor
In this paper, a metamaterial based compact multiband microstrip antenna is proposed which can give high gain and directivity. Metamaterials are periodic structures and have been intensively investigated due to the particular features such as ultra-refraction phenomenon and negative permittivity and/or permeability. A metamaterialbased microstrip patch antenna with enhanced characteristics and multi band operation will be investigated in this work. The multiple frequency operation will be achieved by varying the capacitance of the metamaterial structure with the help of metallic loadings placed in each metamaterial unit cells. The potential impacts will be miniaturization, reduced cost and reduced power consumption since multiple antennas operating at different frequencies are replaced by a single antenna which can operate at multiple frequencies. The proposed microstrip patch antenna will have its frequencies of operation in the L, S and C bands. The proposed structure is simulated using Agilent Advanced Design System (ADS) 2011.05. It is then fabricated on the FR4 substrate and the performance of the fabricated antenna is measured using the Vector Network Analyzer (VNA)
Gain Enhancement of Series Feed Square Patch Microstrip Antenna Array for S b...ijsrd.com
Gain is the ability of an antenna to concentrate the radiated power in a desired direction. Only small gain can be achieved by single antenna that is why, antenna arrays are required to improve the gain by using different feed networks. This paper describes the design and performance of a series feed antenna array. The operating frequency of 2.4GHz is used. The aim of this paper is to improve the gain of a series feed antenna array. Line feed is used for designing single antenna, 2x1 & 4x1 microstrip antenna array. These series feed microstrip antenna arrays are useful for both S and C band. The proposed antenna is simulated by IE3D version 9.0 Zealand simulation software based on method of moments.
DESIGN OF RECTANGULAR PATCH ANTEENA USING METAMATERIAL SUBSTRATEPrateek Kumar
Dissertation part-1 presentation on design of rectangular patch antenna using metamaterial substrate by Prateek Kumar from RUSTAMJI INSTITUTE OF TECHNOLOGY BORDER SECURITY FORCE TEKANPUR GWALIOR (M.P).
A Novel Design of a Miniature Metamaterial Antenna for RFID Reader ApplicationsTELKOMNIKA JOURNAL
In this article, we propose a novel design of a dual band antenna based metamaterial for RFID
applications. The proposed antenna consists of a rectangular patch using inverted u-slot in radiating
element and two split ring resonators loaded in the ground plane. The antenna is printed on an FR4
substrate having athickness of 1.6 mm, permitivitty of 4.4 and loss tanget of 0.025. this antenna is feed by
a micostrip line having caracteristique of 50 Ohms. The designed antenna resonates at the UHF band
around 900Mz with an input impedance of 87MHz and also, resonates at the ISM band around 2.45GHz
with a large bandwidth about 516MHz. The designed antenna is simulated bys using CST and the results
is validated by HFSS. After simulation, a prototype of the proposed antenna is fabricated, and the
measured results show a good agreement with the simulated one.
Metamaterial loaded microstrip patch antenna for quad band operationeSAT Journals
Abstract In this paper, a novel design for miniaturization of microstrip patch antenna with multiband operation of microstrip antenna is proposed. The technique is based on etching out of Complimentary Split-Ring Resonator (CSRR) on the radiating edge of the patch antenna. Numerical simulations are presented for a patch antenna with and without CSRRs by using IE3D simulation software and measured practically. The measured results shows that antenna with CSRRs on the radiating edge of the patch antenna is resonating at four different frequency points i.e., 4.96GHz, 6.05GHz, 8.62GHz and 11.25GHz., whereas, antenna without CSRR i.e., conventional microstrip antenna is resonating at 5.98GHz. The size reduction of 16.92% is achieved and the antenna gives the overall bandwidth of 17.88%. These antennas find application in Wireless Communications. Keywords: microstrip antenna, CSRR, return loss, miniaturization, bandwidth.
Artificial intelligence in the design of microstrip antennaRaj Kumar Thenua
This work presents a Neural Network model for the design of Microstrip Antenna for a desired frequency between 3.5 GHz to 5.5 GHz. The results obtained from the proposed method are compared with the results of IE3D and are found to be in good agreement. The advantage of the proposed method lies with the fact that the various parameters required for the design of specific Microstrip antenna at a particular frequency of interest can be easily extracted without going into the rigorous time consuming, iterative design procedures using a costly software package. In this work, a general design procedure is suggested for the Microstrip antennas using artificial neural networks and this is demonstrated using the rectangular patch geometry.
A Triple Band Bow Tie Array Antenna Using Both-sided MIC Technology IJECEIAES
A single-fed linearly polarized 2x2 microstrip bow tie array antenna is proposed. The feed network has microstrip line and slot line where microstrip-slot branch circuit is connected in parallel. The feed network of the array is designed using both-sided M IC Technology to overcome the impedance matching problem of conventional feed networks. The 2x2 half bow tie array antenna is also truncated with spur lines for optimization of antenna performance. The array antenna unit can be realized in very simple and compact structure, as all the antenna elements and the feeding circuit is arranged on a Teflon glass fiber substrate without requiring any external network. The design frequency of the proposed antenna is 5 to 8 GHz (C- Band) and the obtained peak gain is 12.41 dBi. The resultant axial ratio indicates that linear polarization is achieved.
Extended-Bandwidth Microstrip Circular Patch Antenna for Dual Band Applications IJECEIAES
This paper presents a new wideband microstrip circular patch antenna (MCPA) fed by proximity-coupled line with double-stub matching to achieve dual-band operation. Bandwidth extension is achieved by exciting higherorder modes in the circular radiating patch, and using two stubs to achieve adequate matching across the obtained two bands. The characteristics of the antenna such as reflection coefficient, impedance bandwidth, gain and radiation pattern are investigated and optimized through parametric studies using the CST Microwave Studio Suite. The antenna achieved a large relative bandwidth of 45.16% at the upper band, while the lower one has 10.3% relative bandwidth. The maximum achieved gain of the dual-band antenna in the 5.8GHz band is 4.62dBi while it is 4.85dBi in the upper band. The antenna has an overall size of 30×30×3.2mm3 corresponding to 0.58λ × 0.58 λ × 0.062 λ at the lower band of 5.8 GHz. The proposed antenna should be useful for WLAN and X-band communication systems.
In this paper a compact, flexible, Multiband antenna is designed. It is having flexible Substrate of photographic paper which makes the antenna conformal. The antenna with two U slots cut in radiating patch is offset fed by microstrip lines gives the multiple bands of WLAN/WIMAX Application and two parasitic Elements improves the bandwidth of a typical microstrip antenna. The Measured results shows that the antenna resonates between Frequency band 2.10-2.95 GHz, 3.35-3.54 GHz and 5.04-6.0Hz.which are used for application such as Bluetooth, Wi-Fi, Zigbee, ISM 2.4GHz,WLAN WiMAX, and WLAN 5.2GHz.
5G Fixed Beam Switching on Microstrip Patch Antenna IJECEIAES
5G technology is using millimeter-wave band to improve the wireless communication system. However, narrow transmitter and receiver beams have caused the beam coverage area to be limited. Due to propagation limitations of mm wave band, beam forming technology with multi-beam based communication system, has been focused to overcome the problem. In this letter, a fixed beam switching method is introduced. By changing the switches, four different configurations of patch array antennas are designed to investigate their performances in terms of radiation patterns, beam forming angle, gain, half-power bandwidth and impedance bandwidth at 28 GHz operating frequency for 5G application. Mircostrip antenna is preferred due to its low profile, easy in feeding and array configurations. Three different beam directions had been formed at -15°, 0°, and 15° with half-power bandwidth of range 45˚ to 50˚.
The implementations of the microstrip patch antenna for wireless local area network (WLAN) and worldwide interoperability for microwave access (WiMAX) are analyzed in the literature in this research. Dual or multiband antenna has played a significant part in meeting the expectations of wireless service in this quickly developing world of wireless communication. Basically, a transitory guide, an antenna is a device that emits or absorbs radio waves. Numerous benefits exist for microstrip patch antennas, including affordability, portability, simplicity of construction, and compatibility with integrated circuits. This has several important uses in the military, radar, mobile communications, global positioning system (GPS), remote sensing, and more. In mobile devices like portable computers and smartphones, WLAN and WiMAX are often used.
DESIGN OF RECTANGULAR PATCH ANTEENA USING METAMATERIAL SUBSTRATEPrateek Kumar
Dissertation part-1 presentation on design of rectangular patch antenna using metamaterial substrate by Prateek Kumar from RUSTAMJI INSTITUTE OF TECHNOLOGY BORDER SECURITY FORCE TEKANPUR GWALIOR (M.P).
A Novel Design of a Miniature Metamaterial Antenna for RFID Reader ApplicationsTELKOMNIKA JOURNAL
In this article, we propose a novel design of a dual band antenna based metamaterial for RFID
applications. The proposed antenna consists of a rectangular patch using inverted u-slot in radiating
element and two split ring resonators loaded in the ground plane. The antenna is printed on an FR4
substrate having athickness of 1.6 mm, permitivitty of 4.4 and loss tanget of 0.025. this antenna is feed by
a micostrip line having caracteristique of 50 Ohms. The designed antenna resonates at the UHF band
around 900Mz with an input impedance of 87MHz and also, resonates at the ISM band around 2.45GHz
with a large bandwidth about 516MHz. The designed antenna is simulated bys using CST and the results
is validated by HFSS. After simulation, a prototype of the proposed antenna is fabricated, and the
measured results show a good agreement with the simulated one.
Metamaterial loaded microstrip patch antenna for quad band operationeSAT Journals
Abstract In this paper, a novel design for miniaturization of microstrip patch antenna with multiband operation of microstrip antenna is proposed. The technique is based on etching out of Complimentary Split-Ring Resonator (CSRR) on the radiating edge of the patch antenna. Numerical simulations are presented for a patch antenna with and without CSRRs by using IE3D simulation software and measured practically. The measured results shows that antenna with CSRRs on the radiating edge of the patch antenna is resonating at four different frequency points i.e., 4.96GHz, 6.05GHz, 8.62GHz and 11.25GHz., whereas, antenna without CSRR i.e., conventional microstrip antenna is resonating at 5.98GHz. The size reduction of 16.92% is achieved and the antenna gives the overall bandwidth of 17.88%. These antennas find application in Wireless Communications. Keywords: microstrip antenna, CSRR, return loss, miniaturization, bandwidth.
Artificial intelligence in the design of microstrip antennaRaj Kumar Thenua
This work presents a Neural Network model for the design of Microstrip Antenna for a desired frequency between 3.5 GHz to 5.5 GHz. The results obtained from the proposed method are compared with the results of IE3D and are found to be in good agreement. The advantage of the proposed method lies with the fact that the various parameters required for the design of specific Microstrip antenna at a particular frequency of interest can be easily extracted without going into the rigorous time consuming, iterative design procedures using a costly software package. In this work, a general design procedure is suggested for the Microstrip antennas using artificial neural networks and this is demonstrated using the rectangular patch geometry.
A Triple Band Bow Tie Array Antenna Using Both-sided MIC Technology IJECEIAES
A single-fed linearly polarized 2x2 microstrip bow tie array antenna is proposed. The feed network has microstrip line and slot line where microstrip-slot branch circuit is connected in parallel. The feed network of the array is designed using both-sided M IC Technology to overcome the impedance matching problem of conventional feed networks. The 2x2 half bow tie array antenna is also truncated with spur lines for optimization of antenna performance. The array antenna unit can be realized in very simple and compact structure, as all the antenna elements and the feeding circuit is arranged on a Teflon glass fiber substrate without requiring any external network. The design frequency of the proposed antenna is 5 to 8 GHz (C- Band) and the obtained peak gain is 12.41 dBi. The resultant axial ratio indicates that linear polarization is achieved.
Extended-Bandwidth Microstrip Circular Patch Antenna for Dual Band Applications IJECEIAES
This paper presents a new wideband microstrip circular patch antenna (MCPA) fed by proximity-coupled line with double-stub matching to achieve dual-band operation. Bandwidth extension is achieved by exciting higherorder modes in the circular radiating patch, and using two stubs to achieve adequate matching across the obtained two bands. The characteristics of the antenna such as reflection coefficient, impedance bandwidth, gain and radiation pattern are investigated and optimized through parametric studies using the CST Microwave Studio Suite. The antenna achieved a large relative bandwidth of 45.16% at the upper band, while the lower one has 10.3% relative bandwidth. The maximum achieved gain of the dual-band antenna in the 5.8GHz band is 4.62dBi while it is 4.85dBi in the upper band. The antenna has an overall size of 30×30×3.2mm3 corresponding to 0.58λ × 0.58 λ × 0.062 λ at the lower band of 5.8 GHz. The proposed antenna should be useful for WLAN and X-band communication systems.
In this paper a compact, flexible, Multiband antenna is designed. It is having flexible Substrate of photographic paper which makes the antenna conformal. The antenna with two U slots cut in radiating patch is offset fed by microstrip lines gives the multiple bands of WLAN/WIMAX Application and two parasitic Elements improves the bandwidth of a typical microstrip antenna. The Measured results shows that the antenna resonates between Frequency band 2.10-2.95 GHz, 3.35-3.54 GHz and 5.04-6.0Hz.which are used for application such as Bluetooth, Wi-Fi, Zigbee, ISM 2.4GHz,WLAN WiMAX, and WLAN 5.2GHz.
5G Fixed Beam Switching on Microstrip Patch Antenna IJECEIAES
5G technology is using millimeter-wave band to improve the wireless communication system. However, narrow transmitter and receiver beams have caused the beam coverage area to be limited. Due to propagation limitations of mm wave band, beam forming technology with multi-beam based communication system, has been focused to overcome the problem. In this letter, a fixed beam switching method is introduced. By changing the switches, four different configurations of patch array antennas are designed to investigate their performances in terms of radiation patterns, beam forming angle, gain, half-power bandwidth and impedance bandwidth at 28 GHz operating frequency for 5G application. Mircostrip antenna is preferred due to its low profile, easy in feeding and array configurations. Three different beam directions had been formed at -15°, 0°, and 15° with half-power bandwidth of range 45˚ to 50˚.
The implementations of the microstrip patch antenna for wireless local area network (WLAN) and worldwide interoperability for microwave access (WiMAX) are analyzed in the literature in this research. Dual or multiband antenna has played a significant part in meeting the expectations of wireless service in this quickly developing world of wireless communication. Basically, a transitory guide, an antenna is a device that emits or absorbs radio waves. Numerous benefits exist for microstrip patch antennas, including affordability, portability, simplicity of construction, and compatibility with integrated circuits. This has several important uses in the military, radar, mobile communications, global positioning system (GPS), remote sensing, and more. In mobile devices like portable computers and smartphones, WLAN and WiMAX are often used.
Performance Analysis of Corporate Feed Rectangular Patch Element and Circular...Mohamed Hassouna
This paper present simple, slim, low cost and high gain circular patch and rectangular patch microstrip array antenna, with the details steps of design process, operate in X-band(8 GHz to 12 GHz) and it provides a mean to choose the effective one based on the performance analysis of both of these array antennas. The method of analysis, design and development of these array antennas are explained completely here and analyses are carried out for 4x2 arrays. The simulation has been performed by using commercially available antenna simulator, SONNET version V12.56, to compute the current distribution, return loss response and radiation pattern. The proposed antennas are designed by using Taconic TLY-5 dielectric substrate with permittivity, εr = 2.2 and height, h =1.588 mm. In all cases we get return losses in the range -4.96 dB to -25.21 dB at frequencies around 10 GHz. The gain of these antennas as simulated are found above 6 dB and side lobe label is maintained lower than main lobe. Operating frequency of these antennas is 10 GHz so these antennas are suitable for X-band application.
Parametric Analysis of Single Element U Slot Microstrip AntennaIJSRD
In wireless communication system antennas are the most important element for creating communication link between source and destination. Microsrtip antennas are used for mobile and other satellite communication application because of their light weight, low power handling capacity and low profile. The modern mobile communication system requires high gain, wide bandwidth and minimal size antennas that are capable of providing better performance over a wide range of frequency spectrum. This requirement leads to the design of microsrtip patch array antenna. This paper proposes the parametric analysis of single element U slot MSA. Low dielectric constant substrates are generally preferred for maximum radiation. Thus it prefers FR4 as a dielectric substrate. Desired patch antenna design is simulated by using high frequency simulation software and patch antenna is designed as per requirement. Antenna dimensions such as Length (L), Width (W), and substrate dielectric constant and parameters like Return Loss, Gain, impedance and current distribution are calculated using CAD-FEKO. The antenna has been design to be operated in the range of 8-12GHz. Hence this antenna is highly suitable for X-band applications.
Rectangular and circular antennas design for Bluetooth applicationsTELKOMNIKA JOURNAL
The most researched and examined aspect of the communication system is the wireless connection. Without learning how to operate and use different types of antennas, your knowledge is incomplete. Microstrip patch antenna research has advanced significantly in recent years. When compared to standard antennas, microstrip patch antennas provide additional advantages and opportunities. It is of low volume, light weight, low cost, low appearance, compact and easy to manufacture. This study investigates the differences between rectangular and circular patch antennas. For Bluetooth applications, the center frequency of 2.4 GHz was chosen as the optimal resonant frequency. On a flame retardant (FR-4) epoxy substrate, the antenna dielectric constant is 4.4. Above the ground the base rises 3.6 mm. For the simulation process, high frequency simulation software (HFSS 15) is used as the program design. Antennas 1×1, 1×2, and 1×4 are designed for both circular and rectangular antennas. A comparison was made for both types of antennas and voltage standing wave ratio (VSWR), return losses, gain, directivity and half power beam width (HPBW) were found, and the feature of the rectangular antenna was shown.
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
COLLEGE BUS MANAGEMENT SYSTEM PROJECT REPORT.pdfKamal Acharya
The College Bus Management system is completely developed by Visual Basic .NET Version. The application is connect with most secured database language MS SQL Server. The application is develop by using best combination of front-end and back-end languages. The application is totally design like flat user interface. This flat user interface is more attractive user interface in 2017. The application is gives more important to the system functionality. The application is to manage the student’s details, driver’s details, bus details, bus route details, bus fees details and more. The application has only one unit for admin. The admin can manage the entire application. The admin can login into the application by using username and password of the admin. The application is develop for big and small colleges. It is more user friendly for non-computer person. Even they can easily learn how to manage the application within hours. The application is more secure by the admin. The system will give an effective output for the VB.Net and SQL Server given as input to the system. The compiled java program given as input to the system, after scanning the program will generate different reports. The application generates the report for users. The admin can view and download the report of the data. The application deliver the excel format reports. Because, excel formatted reports is very easy to understand the income and expense of the college bus. This application is mainly develop for windows operating system users. In 2017, 73% of people enterprises are using windows operating system. So the application will easily install for all the windows operating system users. The application-developed size is very low. The application consumes very low space in disk. Therefore, the user can allocate very minimum local disk space for this application.
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
Forklift Classes Overview by Intella PartsIntella Parts
Discover the different forklift classes and their specific applications. Learn how to choose the right forklift for your needs to ensure safety, efficiency, and compliance in your operations.
For more technical information, visit our website https://intellaparts.com
CFD Simulation of By-pass Flow in a HRSG module by R&R Consult.pptxR&R Consult
CFD analysis is incredibly effective at solving mysteries and improving the performance of complex systems!
Here's a great example: At a large natural gas-fired power plant, where they use waste heat to generate steam and energy, they were puzzled that their boiler wasn't producing as much steam as expected.
R&R and Tetra Engineering Group Inc. were asked to solve the issue with reduced steam production.
An inspection had shown that a significant amount of hot flue gas was bypassing the boiler tubes, where the heat was supposed to be transferred.
R&R Consult conducted a CFD analysis, which revealed that 6.3% of the flue gas was bypassing the boiler tubes without transferring heat. The analysis also showed that the flue gas was instead being directed along the sides of the boiler and between the modules that were supposed to capture the heat. This was the cause of the reduced performance.
Based on our results, Tetra Engineering installed covering plates to reduce the bypass flow. This improved the boiler's performance and increased electricity production.
It is always satisfying when we can help solve complex challenges like this. Do your systems also need a check-up or optimization? Give us a call!
Work done in cooperation with James Malloy and David Moelling from Tetra Engineering.
More examples of our work https://www.r-r-consult.dk/en/cases-en/
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers