This document analyzes the physico-chemical parameters of underground water samples from selected areas of Satna District in Madhya Pradesh, India. Water samples were collected from 9 locations and tested for various parameters including temperature, pH, alkalinity, hardness, TDS, EC, DO, BOD, and COD. The results found that most parameters were within permissible limits but the water quality was not suitable for drinking due to higher levels of certain parameters. While the water quality needs improvement, most parameters met groundwater quality standards. The analysis helps communicate the current water quality to citizens and policymakers.
INFLUENCE OF LEACHATE MIGRATION ON GROUND WATER QUALITY Dr. Naveen BP
In this paper, the concept of leachate pollution index, a tool for quantifying the leachate pollution potential and water quality index for surrounding water bodies of Mavallipura landfill site in Bangalore has been applied. It has been found that the leachate generated from the Mavallipura landfill site has high contamination potential to the surrounding water bodies. The results revealed that quality of ground water resources in Mavallipura landfill is deteriorating largely, as a result of the poor practice of solid waste management. Hence, an effective remedial plan needs to be prepared for the sustainable water quality maintenance of the area.
CHARACTERIZATION OF LEACHATE FROM MUNCIPAL LANDFILL AND ITS EFFECT ON SURROUN...Dr. Naveen BP
Percolating water passing through waste becomes contaminated and will have dissolved soluble organic and inorganic compounds as well as suspended particles. Also the pore fluid of the waste is often released and mixes with this water. The entire contaminated fluid is called leachate. There are many factors that affect leachate production like annual precipitation, runoff, infiltration, evaporation, transpiration, and freezing, mean ambient temperature, waste composition, waste density, initial moisture content, and depth of the waste fill. The production of leachate reduces when a landfill is closed. The decomposition of waste in presence of water can be separated into two different phases of degradation viz., initial aerobic and subsequent anaerobic. Generally, the leachate undergoes natural chemical changes over time that reduces its toxicity. Some of the soluble contaminants enrich the water table, or the saturated zone. Some of remaining molecules naturally adsorbed to the clay liner particles. The paper discusses the characteristics of leachate generated from municipal solid waste landfill and its effect on surrounding water bodies near Mavallipura landfill area in Bangalore. Two samples of water from the nearby pond and well were collected from downstream of Mavallipura landfill site. Physico-chemical characterization of leachate has shown that the leachate contains high concentrations of organic and inorganic constituents beyond the permissible limits. While the heavy metals concentration was in traces as the waste is dumped in the landfill is mainly domestic in nature. The pH of the leachate is marginally alkaline as the pH is 7.4. The results also showed that the highest metal concentration that exists in the leachate was Iron which is about of 11.16 ppm. BOD5 and COD of the leachate are 1500 mg/l and 10400 mg/l, respectively. The leachate characteristics indicate favorable growth of algae in natural water contaminated with leachate with the alkaline condition and with the presence of magnesium as nutrient, which has been confirmed in the nearby surface pond. Knowledge of leachate quality will be useful in planning and providing remedial measures to protect surface and ground water quality in the area.
INFLUENCE OF LEACHATE MIGRATION ON GROUND WATER QUALITY Dr. Naveen BP
In this paper, the concept of leachate pollution index, a tool for quantifying the leachate pollution potential and water quality index for surrounding water bodies of Mavallipura landfill site in Bangalore has been applied. It has been found that the leachate generated from the Mavallipura landfill site has high contamination potential to the surrounding water bodies. The results revealed that quality of ground water resources in Mavallipura landfill is deteriorating largely, as a result of the poor practice of solid waste management. Hence, an effective remedial plan needs to be prepared for the sustainable water quality maintenance of the area.
CHARACTERIZATION OF LEACHATE FROM MUNCIPAL LANDFILL AND ITS EFFECT ON SURROUN...Dr. Naveen BP
Percolating water passing through waste becomes contaminated and will have dissolved soluble organic and inorganic compounds as well as suspended particles. Also the pore fluid of the waste is often released and mixes with this water. The entire contaminated fluid is called leachate. There are many factors that affect leachate production like annual precipitation, runoff, infiltration, evaporation, transpiration, and freezing, mean ambient temperature, waste composition, waste density, initial moisture content, and depth of the waste fill. The production of leachate reduces when a landfill is closed. The decomposition of waste in presence of water can be separated into two different phases of degradation viz., initial aerobic and subsequent anaerobic. Generally, the leachate undergoes natural chemical changes over time that reduces its toxicity. Some of the soluble contaminants enrich the water table, or the saturated zone. Some of remaining molecules naturally adsorbed to the clay liner particles. The paper discusses the characteristics of leachate generated from municipal solid waste landfill and its effect on surrounding water bodies near Mavallipura landfill area in Bangalore. Two samples of water from the nearby pond and well were collected from downstream of Mavallipura landfill site. Physico-chemical characterization of leachate has shown that the leachate contains high concentrations of organic and inorganic constituents beyond the permissible limits. While the heavy metals concentration was in traces as the waste is dumped in the landfill is mainly domestic in nature. The pH of the leachate is marginally alkaline as the pH is 7.4. The results also showed that the highest metal concentration that exists in the leachate was Iron which is about of 11.16 ppm. BOD5 and COD of the leachate are 1500 mg/l and 10400 mg/l, respectively. The leachate characteristics indicate favorable growth of algae in natural water contaminated with leachate with the alkaline condition and with the presence of magnesium as nutrient, which has been confirmed in the nearby surface pond. Knowledge of leachate quality will be useful in planning and providing remedial measures to protect surface and ground water quality in the area.
study of ground water quality of raichur in industrial zone in concernIJAEMSJORNAL
This paper gives the information of the groundwater quality of Raichur industrial area. Different areas were selected for the study and comparison. The parameters studied were temperature, pH, total alkalinity, total hardness, chloride, sulphate, fluoride, total dissolved solids and conductivity. It was observed that there was a minor fluctuation in the physico-chemical parameters among the water samples studied from overall analysis. The groundwater is highly contaminated and account for health hazards for human use from the Comparison of the physico-chemical parameters of the water sample with WHO and ICMR limits.
Study on Assessment of Physico chemical properties of Industrial wastesIJEAB
The physicochemical parameters of wastewater collected from five sampling sites were investigated. These parameters were analyzed by standard methods. The pH of the waste water varied from 4.7 to7.66, while the waste water conductivity ranges from 1205.3 to 7130.17 µScm−1. The maximum total dissolved solid was 8100mg/l.and the maximum biological oxygen demand was 2763.35 mg/l. The chemical oxygen demand of the selected samplesites varied widely (772.56–3105.13 mg/l), the nitrate content was found to be maximum in sample W5 (166.00mg/l), and the sulfate content was found to be high in samples W1 andW5 (500and 4875mg/l). The chloride and sulphied contents were maximum at samples of W3 and W5 their concentrations were8543.45 and 10.7mg/l respectively. The physic chemical parameters studied in this work were varied between the samples and almost all parameters studied were higher compared with the permissible limit prescribed by the United States Environmental Protection Agency and World Health Organization.
THE EFFECT OF WATER TREATMENT ON SELENIUM AND VANADIUM LEVELS OF WATER IN KAR...EDITOR IJCRCPS
Introduction: Due to the increase in world population and increased demand for safe drinking water, using of bottled water,
especially in areas with a shortage of safe drinking water is common. The aim of this research was to compare Selenium and
Vanadium levels in the water of Karun river at the influent stream of the water treatment plant number 2 (WTP2) and its outlet
water after the water treatment process and waters of inlet and outlet of Byblus factory and Anahita factory in Ahvaz city. Materials
and Methods: Fourteen samples of Karun river water at the inlet of Ahvaz WTP2 and its outlet water after the water treatment
process and waters of inlet and outlet of Byblus factory and Anahita factory were collected during five months (September 2013,
and January - April 2014). Samples were taken fourteen times, each time; five, one - liter samples were collected. The samples
were mixed and one liter composite sample was isolated and transported to laboratory. The collected samples were filtered
through filter paper (0.45 μm). For their fixation and protection, nitric acid was added and the pH was adjusted at≤2. All samples
were analyzed by ICP-MS. Results & Discussion: According to the results, the highest and lowest mean concentration of
Vanadium 14.22 and 6.17 ppb in Water inlet the water treatment plant NO (2) of Ahvaz and water at outlet from Anahita factory.
The mean concentration of selenium because of the lower limit (0.1 ppb) was not measured with ICP-MS. Conclusion: The results
showed that the purification process causes reduction in content of metals in water.
Keywords: Karun River, Selenium, Vanadium, Water Treatment Plant, ICP-MS.
Seasonal Variations in Physico-Chemical Parameter of Groundwater in Bhimavara...IJERD Editor
Physico-chemical analysis of open well water samples was carried out from 10 sampling locations
in Bhimavaram town during three seasons namely summer, rainy and winter of 2012-‟13 are presented. The
quality analysis was made through the estimation of physico-chemical parameters such as pH,
Turbidity, EC, TDS, Cl–, SO4
2–, NO3
–, PO4
3–, D.O, TH, Ca2+, Mg2+, F–, Na+, K+ and BOD. Each parameter was
compared with its standard permissible limit as prescribed by World Health Organization (WHO) and BIS
standard to assess the suitability of drinking and domestic purposes. The analytical results of groundwater
samples shows that that certain parameters namely PH, D.O and Fluoride were found within the desirable limits
by BIS. However, Turbidity, EC, TH, TDS, BOD, Chloride, Sulphate, Phosphate, Nitrate, Sodium, Potassium,
Calcium, were exceding the desirable limit throughout the investigation period in all locations.The results of
analysis reveal that the ground water of the area was not suitable for human consumption and domestic use due
to the influence saltwater intrusion, sewage, Industrial effluents and high urban concentration are the probable
sources for the variation of water quality in the study area
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
This presentation describes, how the water can be analyzed using the basic parameters like DO, COD, BOD, Alkalinity and so on. The physical, chemical, and biological parameters were discussed here.
IOSR Journal of Applied Chemistry (IOSR-JAC) is an open access international journal that provides rapid publication (within a month) of articles in all areas of applied chemistry and its applications. The journal welcomes publications of high quality papers on theoretical developments and practical applications in Chemical Science. Original research papers, state-of-the-art reviews, and high quality technical notes are invited for publications.
study of ground water quality of raichur in industrial zone in concernIJAEMSJORNAL
This paper gives the information of the groundwater quality of Raichur industrial area. Different areas were selected for the study and comparison. The parameters studied were temperature, pH, total alkalinity, total hardness, chloride, sulphate, fluoride, total dissolved solids and conductivity. It was observed that there was a minor fluctuation in the physico-chemical parameters among the water samples studied from overall analysis. The groundwater is highly contaminated and account for health hazards for human use from the Comparison of the physico-chemical parameters of the water sample with WHO and ICMR limits.
Study on Assessment of Physico chemical properties of Industrial wastesIJEAB
The physicochemical parameters of wastewater collected from five sampling sites were investigated. These parameters were analyzed by standard methods. The pH of the waste water varied from 4.7 to7.66, while the waste water conductivity ranges from 1205.3 to 7130.17 µScm−1. The maximum total dissolved solid was 8100mg/l.and the maximum biological oxygen demand was 2763.35 mg/l. The chemical oxygen demand of the selected samplesites varied widely (772.56–3105.13 mg/l), the nitrate content was found to be maximum in sample W5 (166.00mg/l), and the sulfate content was found to be high in samples W1 andW5 (500and 4875mg/l). The chloride and sulphied contents were maximum at samples of W3 and W5 their concentrations were8543.45 and 10.7mg/l respectively. The physic chemical parameters studied in this work were varied between the samples and almost all parameters studied were higher compared with the permissible limit prescribed by the United States Environmental Protection Agency and World Health Organization.
THE EFFECT OF WATER TREATMENT ON SELENIUM AND VANADIUM LEVELS OF WATER IN KAR...EDITOR IJCRCPS
Introduction: Due to the increase in world population and increased demand for safe drinking water, using of bottled water,
especially in areas with a shortage of safe drinking water is common. The aim of this research was to compare Selenium and
Vanadium levels in the water of Karun river at the influent stream of the water treatment plant number 2 (WTP2) and its outlet
water after the water treatment process and waters of inlet and outlet of Byblus factory and Anahita factory in Ahvaz city. Materials
and Methods: Fourteen samples of Karun river water at the inlet of Ahvaz WTP2 and its outlet water after the water treatment
process and waters of inlet and outlet of Byblus factory and Anahita factory were collected during five months (September 2013,
and January - April 2014). Samples were taken fourteen times, each time; five, one - liter samples were collected. The samples
were mixed and one liter composite sample was isolated and transported to laboratory. The collected samples were filtered
through filter paper (0.45 μm). For their fixation and protection, nitric acid was added and the pH was adjusted at≤2. All samples
were analyzed by ICP-MS. Results & Discussion: According to the results, the highest and lowest mean concentration of
Vanadium 14.22 and 6.17 ppb in Water inlet the water treatment plant NO (2) of Ahvaz and water at outlet from Anahita factory.
The mean concentration of selenium because of the lower limit (0.1 ppb) was not measured with ICP-MS. Conclusion: The results
showed that the purification process causes reduction in content of metals in water.
Keywords: Karun River, Selenium, Vanadium, Water Treatment Plant, ICP-MS.
Seasonal Variations in Physico-Chemical Parameter of Groundwater in Bhimavara...IJERD Editor
Physico-chemical analysis of open well water samples was carried out from 10 sampling locations
in Bhimavaram town during three seasons namely summer, rainy and winter of 2012-‟13 are presented. The
quality analysis was made through the estimation of physico-chemical parameters such as pH,
Turbidity, EC, TDS, Cl–, SO4
2–, NO3
–, PO4
3–, D.O, TH, Ca2+, Mg2+, F–, Na+, K+ and BOD. Each parameter was
compared with its standard permissible limit as prescribed by World Health Organization (WHO) and BIS
standard to assess the suitability of drinking and domestic purposes. The analytical results of groundwater
samples shows that that certain parameters namely PH, D.O and Fluoride were found within the desirable limits
by BIS. However, Turbidity, EC, TH, TDS, BOD, Chloride, Sulphate, Phosphate, Nitrate, Sodium, Potassium,
Calcium, were exceding the desirable limit throughout the investigation period in all locations.The results of
analysis reveal that the ground water of the area was not suitable for human consumption and domestic use due
to the influence saltwater intrusion, sewage, Industrial effluents and high urban concentration are the probable
sources for the variation of water quality in the study area
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
This presentation describes, how the water can be analyzed using the basic parameters like DO, COD, BOD, Alkalinity and so on. The physical, chemical, and biological parameters were discussed here.
IOSR Journal of Applied Chemistry (IOSR-JAC) is an open access international journal that provides rapid publication (within a month) of articles in all areas of applied chemistry and its applications. The journal welcomes publications of high quality papers on theoretical developments and practical applications in Chemical Science. Original research papers, state-of-the-art reviews, and high quality technical notes are invited for publications.
Water is an important natural resource, which forms the cause of all life. Water is
one of the most requisite materials in our day to day life. It is a key resource in all
economic activities ranging from agriculture to industries. Only a minimal fraction of
the planet’s plentiful water is available to the living beings as fresh water. About 97%
is found in the oceans and is very salty for drinking, irrigation, or industry. The
remaining 3% is fresh water. About 2.997% of it is arrested in ice caps or glaciers or
is concealed so deep that it costs too much time & money to extract. Only about
0.0035 of Earth’s total volume of water is easily available to us as soil moisture,
exploitable ground water, water vapor, rivers, lakes and streams. In this present study
by a systematic sampling has been carried out to find the water quality parameters of
the Lake, by collecting samples from Six different positions, which covering entire
area of the lake, and the stations were distributed covering the periphery of the entire
tank, and also considering the inflow and the discharges and to suggest required
management techniques to make water free from the pollution
Democratizing Fuzzing at Scale by Abhishek Aryaabh.arya
Presented at NUS: Fuzzing and Software Security Summer School 2024
This keynote talks about the democratization of fuzzing at scale, highlighting the collaboration between open source communities, academia, and industry to advance the field of fuzzing. It delves into the history of fuzzing, the development of scalable fuzzing platforms, and the empowerment of community-driven research. The talk will further discuss recent advancements leveraging AI/ML and offer insights into the future evolution of the fuzzing landscape.
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Quality defects in TMT Bars, Possible causes and Potential Solutions.PrashantGoswami42
Maintaining high-quality standards in the production of TMT bars is crucial for ensuring structural integrity in construction. Addressing common defects through careful monitoring, standardized processes, and advanced technology can significantly improve the quality of TMT bars. Continuous training and adherence to quality control measures will also play a pivotal role in minimizing these defects.
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
Explore the innovative world of trenchless pipe repair with our comprehensive guide, "The Benefits and Techniques of Trenchless Pipe Repair." This document delves into the modern methods of repairing underground pipes without the need for extensive excavation, highlighting the numerous advantages and the latest techniques used in the industry.
Learn about the cost savings, reduced environmental impact, and minimal disruption associated with trenchless technology. Discover detailed explanations of popular techniques such as pipe bursting, cured-in-place pipe (CIPP) lining, and directional drilling. Understand how these methods can be applied to various types of infrastructure, from residential plumbing to large-scale municipal systems.
Ideal for homeowners, contractors, engineers, and anyone interested in modern plumbing solutions, this guide provides valuable insights into why trenchless pipe repair is becoming the preferred choice for pipe rehabilitation. Stay informed about the latest advancements and best practices in the field.
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
Event Management System Vb Net Project Report.pdfKamal Acharya
In present era, the scopes of information technology growing with a very fast .We do not see any are untouched from this industry. The scope of information technology has become wider includes: Business and industry. Household Business, Communication, Education, Entertainment, Science, Medicine, Engineering, Distance Learning, Weather Forecasting. Carrier Searching and so on.
My project named “Event Management System” is software that store and maintained all events coordinated in college. It also helpful to print related reports. My project will help to record the events coordinated by faculties with their Name, Event subject, date & details in an efficient & effective ways.
In my system we have to make a system by which a user can record all events coordinated by a particular faculty. In our proposed system some more featured are added which differs it from the existing system such as security.
Vaccine management system project report documentation..pdfKamal Acharya
The Division of Vaccine and Immunization is facing increasing difficulty monitoring vaccines and other commodities distribution once they have been distributed from the national stores. With the introduction of new vaccines, more challenges have been anticipated with this additions posing serious threat to the already over strained vaccine supply chain system in Kenya.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Forklift Classes Overview by Intella PartsIntella Parts
Discover the different forklift classes and their specific applications. Learn how to choose the right forklift for your needs to ensure safety, efficiency, and compliance in your operations.
For more technical information, visit our website https://intellaparts.com
COLLEGE BUS MANAGEMENT SYSTEM PROJECT REPORT.pdfKamal Acharya
The College Bus Management system is completely developed by Visual Basic .NET Version. The application is connect with most secured database language MS SQL Server. The application is develop by using best combination of front-end and back-end languages. The application is totally design like flat user interface. This flat user interface is more attractive user interface in 2017. The application is gives more important to the system functionality. The application is to manage the student’s details, driver’s details, bus details, bus route details, bus fees details and more. The application has only one unit for admin. The admin can manage the entire application. The admin can login into the application by using username and password of the admin. The application is develop for big and small colleges. It is more user friendly for non-computer person. Even they can easily learn how to manage the application within hours. The application is more secure by the admin. The system will give an effective output for the VB.Net and SQL Server given as input to the system. The compiled java program given as input to the system, after scanning the program will generate different reports. The application generates the report for users. The admin can view and download the report of the data. The application deliver the excel format reports. Because, excel formatted reports is very easy to understand the income and expense of the college bus. This application is mainly develop for windows operating system users. In 2017, 73% of people enterprises are using windows operating system. So the application will easily install for all the windows operating system users. The application-developed size is very low. The application consumes very low space in disk. Therefore, the user can allocate very minimum local disk space for this application.
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.