This document discusses water reclamation and reuse. It describes the water reclamation process, which involves microfiltration to strain out particles, reverse osmosis to remove minerals, and advanced oxidation with UV light and hydrogen peroxide to disinfect. Tests conducted on wastewater for reclamation include measuring organics, solids, nutrients, and physical properties. The document also discusses the environmental, health, and agricultural aspects of water reclamation and reuse, concluding that it is needed to preserve freshwater sources and can augment water supplies when treated adequately.
ASSESSMENT OF WASTE WATER TREATMENT IN CANAANLAND, OTA, OGUN STATE, NIGERIA.O...Felix Oginni
Effluent from a sewage treatment plant in Covenant University, Canaanland is made to pass through a series of constructed wetland before discharging into a gully that drains into River Iju (also known as Atuara). This river is used as a source of drinking water and also provides food in form of fish for hundreds of thousands of people downstream and eventually enters the lagoon, some 60km away. Effectiveness and adequacy of the wastewater treatment facility in place was assessed in order to improve sanitation within this watershed, thereby alleviating environmental challenges in this coastal region of Nigeria. Waste water is gravity drained to the southwest portion of the campus where the solid is removed and the liquid is allowed to flow through six sets of constructed wetlands, each with four chambers. Within each chamber are water hyacinth plants put in place to remove nutrients from the waster water.
A quick survey of the facility shows the system to be effective in reducing and removing solids and dissolved solids from the waste water. The pH ranged between 6.6 and 6.8, conductivity from 530 to 600, and total dissolved solids (TDS) ranged from 360 – 400 ppm. The data obtained indicate that some modifications need to be made as the waste water treatment system is not very efficient in reducing the amount of TDS and nutrients. The flow rate is considered to be very high from cell to cell, thereby not allowing time for the plants and microbes to reduce the TDS. It is suggested that some method be devised to slow down the flow rate to allow the plants and microbes to work on reducing the TDS. Parameters also also considered included DO, E. Coli. Nitrate and Phosphates.
Desalination Overview and 24 MLD Jaffna SWRO Project May, 2015 - Water Globe.Private Consultants
TA-8668 SRI: Rapid Assessment of Seawater Desalination and
Other Alternative Water Sources for Jaffna Water Supply Water - Globe Consulting Nikolay Voutchkov
ASSESSMENT OF WASTE WATER TREATMENT IN CANAANLAND, OTA, OGUN STATE, NIGERIA.O...Felix Oginni
Effluent from a sewage treatment plant in Covenant University, Canaanland is made to pass through a series of constructed wetland before discharging into a gully that drains into River Iju (also known as Atuara). This river is used as a source of drinking water and also provides food in form of fish for hundreds of thousands of people downstream and eventually enters the lagoon, some 60km away. Effectiveness and adequacy of the wastewater treatment facility in place was assessed in order to improve sanitation within this watershed, thereby alleviating environmental challenges in this coastal region of Nigeria. Waste water is gravity drained to the southwest portion of the campus where the solid is removed and the liquid is allowed to flow through six sets of constructed wetlands, each with four chambers. Within each chamber are water hyacinth plants put in place to remove nutrients from the waster water.
A quick survey of the facility shows the system to be effective in reducing and removing solids and dissolved solids from the waste water. The pH ranged between 6.6 and 6.8, conductivity from 530 to 600, and total dissolved solids (TDS) ranged from 360 – 400 ppm. The data obtained indicate that some modifications need to be made as the waste water treatment system is not very efficient in reducing the amount of TDS and nutrients. The flow rate is considered to be very high from cell to cell, thereby not allowing time for the plants and microbes to reduce the TDS. It is suggested that some method be devised to slow down the flow rate to allow the plants and microbes to work on reducing the TDS. Parameters also also considered included DO, E. Coli. Nitrate and Phosphates.
Desalination Overview and 24 MLD Jaffna SWRO Project May, 2015 - Water Globe.Private Consultants
TA-8668 SRI: Rapid Assessment of Seawater Desalination and
Other Alternative Water Sources for Jaffna Water Supply Water - Globe Consulting Nikolay Voutchkov
This is my team's Capstone Senior Design Project from Fall 2021. Our project was to retrofit a drinking water well site with ion exchange vessels for PFAS removal.
Lecture note of Industrial Waste Treatment (Elective -III) as per syllabus of Solapur university for BE Civil
Prepared by
Prof S S Jahagirdar,
Associate Professor,
N K ORchid College of Engg and Tech,
Solapur
Study on Assessment of Physico chemical properties of Industrial wastesIJEAB
The physicochemical parameters of wastewater collected from five sampling sites were investigated. These parameters were analyzed by standard methods. The pH of the waste water varied from 4.7 to7.66, while the waste water conductivity ranges from 1205.3 to 7130.17 µScm−1. The maximum total dissolved solid was 8100mg/l.and the maximum biological oxygen demand was 2763.35 mg/l. The chemical oxygen demand of the selected samplesites varied widely (772.56–3105.13 mg/l), the nitrate content was found to be maximum in sample W5 (166.00mg/l), and the sulfate content was found to be high in samples W1 andW5 (500and 4875mg/l). The chloride and sulphied contents were maximum at samples of W3 and W5 their concentrations were8543.45 and 10.7mg/l respectively. The physic chemical parameters studied in this work were varied between the samples and almost all parameters studied were higher compared with the permissible limit prescribed by the United States Environmental Protection Agency and World Health Organization.
INFLUENCE OF LEACHATE MIGRATION ON GROUND WATER QUALITY Dr. Naveen BP
In this paper, the concept of leachate pollution index, a tool for quantifying the leachate pollution potential and water quality index for surrounding water bodies of Mavallipura landfill site in Bangalore has been applied. It has been found that the leachate generated from the Mavallipura landfill site has high contamination potential to the surrounding water bodies. The results revealed that quality of ground water resources in Mavallipura landfill is deteriorating largely, as a result of the poor practice of solid waste management. Hence, an effective remedial plan needs to be prepared for the sustainable water quality maintenance of the area.
Membrane Separation Technology for Water Treatment in Upstream Oil & Gas Oper...James Robinson
Membrane Separation Technology for Water Treatment in Upstream Oil & Gas Operations
presented by James Robinson on April 20, 2016, at the "Semi-Annual Water & Wastewater Short Course: Issues, Challenges, Solutions & New Technologies" hosted by the Global Petroleum Research Institute (GPRI) at Texas A&M's Department of Petroleum Engineering.
CHARACTERIZATION OF LEACHATE FROM MUNCIPAL LANDFILL AND ITS EFFECT ON SURROUN...Dr. Naveen BP
Percolating water passing through waste becomes contaminated and will have dissolved soluble organic and inorganic compounds as well as suspended particles. Also the pore fluid of the waste is often released and mixes with this water. The entire contaminated fluid is called leachate. There are many factors that affect leachate production like annual precipitation, runoff, infiltration, evaporation, transpiration, and freezing, mean ambient temperature, waste composition, waste density, initial moisture content, and depth of the waste fill. The production of leachate reduces when a landfill is closed. The decomposition of waste in presence of water can be separated into two different phases of degradation viz., initial aerobic and subsequent anaerobic. Generally, the leachate undergoes natural chemical changes over time that reduces its toxicity. Some of the soluble contaminants enrich the water table, or the saturated zone. Some of remaining molecules naturally adsorbed to the clay liner particles. The paper discusses the characteristics of leachate generated from municipal solid waste landfill and its effect on surrounding water bodies near Mavallipura landfill area in Bangalore. Two samples of water from the nearby pond and well were collected from downstream of Mavallipura landfill site. Physico-chemical characterization of leachate has shown that the leachate contains high concentrations of organic and inorganic constituents beyond the permissible limits. While the heavy metals concentration was in traces as the waste is dumped in the landfill is mainly domestic in nature. The pH of the leachate is marginally alkaline as the pH is 7.4. The results also showed that the highest metal concentration that exists in the leachate was Iron which is about of 11.16 ppm. BOD5 and COD of the leachate are 1500 mg/l and 10400 mg/l, respectively. The leachate characteristics indicate favorable growth of algae in natural water contaminated with leachate with the alkaline condition and with the presence of magnesium as nutrient, which has been confirmed in the nearby surface pond. Knowledge of leachate quality will be useful in planning and providing remedial measures to protect surface and ground water quality in the area.
Case study: Algae Control in Drinking Water ReservoirLG Sonic
Since the spring of 2014, four solar-powered algae control buoys are operating in the Canoe Brook Reservoir #1 in Short Hills, New Jersey to control algae and cyanobacteria in the raw water reservoir. The reservoir is managed by American Water, America’s largest publicly traded water and wastewater utility company.
ENVIRONMENTAL EFFECT OF LIFT IRRIGATION SCHEME-A CASE STUDYijiert bestjournal
Purandar Lift Irrigation scheme is on Mula-Mutha River near Pune in India envisaged to supply
4 TMC of water to drought prone area of Purandar, Daund, Haveli & Baramati. It is observed
that the raw water quality available near source is far below the acceptable limits for surface
water irrigation.
The farmers are raising objections for supply of raw water for irrigation purpose. The main
reason for the reluctance of the farmers in using available river water is undesirable organic & in
organic impurities, blackish green color & obnoxious smell of water. The chemical analysis
results indicate that BOD (Biological Oxidation Demand) & COD (Chemical Oxidation
Demand) values of the river water used for irrigation purpose are above permissible limits.
Our main aim in the project was to find out whether the polluted water of the river would have
any long term environmental effects on the soil and ground water of the Saswad-Purandar area.
For this purpose we conducted several site visits to check the extent of pollution of the river
water at different locations. We tested soil & ground water samples of the area where lifted water
is used for irrigation. We also suggested low cost treatmentaerated facultative lagoons to treat the
river water.
This is my team's Capstone Senior Design Project from Fall 2021. Our project was to retrofit a drinking water well site with ion exchange vessels for PFAS removal.
Lecture note of Industrial Waste Treatment (Elective -III) as per syllabus of Solapur university for BE Civil
Prepared by
Prof S S Jahagirdar,
Associate Professor,
N K ORchid College of Engg and Tech,
Solapur
Study on Assessment of Physico chemical properties of Industrial wastesIJEAB
The physicochemical parameters of wastewater collected from five sampling sites were investigated. These parameters were analyzed by standard methods. The pH of the waste water varied from 4.7 to7.66, while the waste water conductivity ranges from 1205.3 to 7130.17 µScm−1. The maximum total dissolved solid was 8100mg/l.and the maximum biological oxygen demand was 2763.35 mg/l. The chemical oxygen demand of the selected samplesites varied widely (772.56–3105.13 mg/l), the nitrate content was found to be maximum in sample W5 (166.00mg/l), and the sulfate content was found to be high in samples W1 andW5 (500and 4875mg/l). The chloride and sulphied contents were maximum at samples of W3 and W5 their concentrations were8543.45 and 10.7mg/l respectively. The physic chemical parameters studied in this work were varied between the samples and almost all parameters studied were higher compared with the permissible limit prescribed by the United States Environmental Protection Agency and World Health Organization.
INFLUENCE OF LEACHATE MIGRATION ON GROUND WATER QUALITY Dr. Naveen BP
In this paper, the concept of leachate pollution index, a tool for quantifying the leachate pollution potential and water quality index for surrounding water bodies of Mavallipura landfill site in Bangalore has been applied. It has been found that the leachate generated from the Mavallipura landfill site has high contamination potential to the surrounding water bodies. The results revealed that quality of ground water resources in Mavallipura landfill is deteriorating largely, as a result of the poor practice of solid waste management. Hence, an effective remedial plan needs to be prepared for the sustainable water quality maintenance of the area.
Membrane Separation Technology for Water Treatment in Upstream Oil & Gas Oper...James Robinson
Membrane Separation Technology for Water Treatment in Upstream Oil & Gas Operations
presented by James Robinson on April 20, 2016, at the "Semi-Annual Water & Wastewater Short Course: Issues, Challenges, Solutions & New Technologies" hosted by the Global Petroleum Research Institute (GPRI) at Texas A&M's Department of Petroleum Engineering.
CHARACTERIZATION OF LEACHATE FROM MUNCIPAL LANDFILL AND ITS EFFECT ON SURROUN...Dr. Naveen BP
Percolating water passing through waste becomes contaminated and will have dissolved soluble organic and inorganic compounds as well as suspended particles. Also the pore fluid of the waste is often released and mixes with this water. The entire contaminated fluid is called leachate. There are many factors that affect leachate production like annual precipitation, runoff, infiltration, evaporation, transpiration, and freezing, mean ambient temperature, waste composition, waste density, initial moisture content, and depth of the waste fill. The production of leachate reduces when a landfill is closed. The decomposition of waste in presence of water can be separated into two different phases of degradation viz., initial aerobic and subsequent anaerobic. Generally, the leachate undergoes natural chemical changes over time that reduces its toxicity. Some of the soluble contaminants enrich the water table, or the saturated zone. Some of remaining molecules naturally adsorbed to the clay liner particles. The paper discusses the characteristics of leachate generated from municipal solid waste landfill and its effect on surrounding water bodies near Mavallipura landfill area in Bangalore. Two samples of water from the nearby pond and well were collected from downstream of Mavallipura landfill site. Physico-chemical characterization of leachate has shown that the leachate contains high concentrations of organic and inorganic constituents beyond the permissible limits. While the heavy metals concentration was in traces as the waste is dumped in the landfill is mainly domestic in nature. The pH of the leachate is marginally alkaline as the pH is 7.4. The results also showed that the highest metal concentration that exists in the leachate was Iron which is about of 11.16 ppm. BOD5 and COD of the leachate are 1500 mg/l and 10400 mg/l, respectively. The leachate characteristics indicate favorable growth of algae in natural water contaminated with leachate with the alkaline condition and with the presence of magnesium as nutrient, which has been confirmed in the nearby surface pond. Knowledge of leachate quality will be useful in planning and providing remedial measures to protect surface and ground water quality in the area.
Case study: Algae Control in Drinking Water ReservoirLG Sonic
Since the spring of 2014, four solar-powered algae control buoys are operating in the Canoe Brook Reservoir #1 in Short Hills, New Jersey to control algae and cyanobacteria in the raw water reservoir. The reservoir is managed by American Water, America’s largest publicly traded water and wastewater utility company.
ENVIRONMENTAL EFFECT OF LIFT IRRIGATION SCHEME-A CASE STUDYijiert bestjournal
Purandar Lift Irrigation scheme is on Mula-Mutha River near Pune in India envisaged to supply
4 TMC of water to drought prone area of Purandar, Daund, Haveli & Baramati. It is observed
that the raw water quality available near source is far below the acceptable limits for surface
water irrigation.
The farmers are raising objections for supply of raw water for irrigation purpose. The main
reason for the reluctance of the farmers in using available river water is undesirable organic & in
organic impurities, blackish green color & obnoxious smell of water. The chemical analysis
results indicate that BOD (Biological Oxidation Demand) & COD (Chemical Oxidation
Demand) values of the river water used for irrigation purpose are above permissible limits.
Our main aim in the project was to find out whether the polluted water of the river would have
any long term environmental effects on the soil and ground water of the Saswad-Purandar area.
For this purpose we conducted several site visits to check the extent of pollution of the river
water at different locations. We tested soil & ground water samples of the area where lifted water
is used for irrigation. We also suggested low cost treatmentaerated facultative lagoons to treat the
river water.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Purification of Wastewater by Metal Oxide Nanoparticlesijtsrd
In todays world, nanotechnology is becoming increasingly popular for water treatment. In this review, we will summarize recent advances in the development of typical metal oxide materials TiO2, Fe3O4 Fe2O3, MnO2, CeO2, MgO and Al2O3 and the related processes for the treatment of various water resources which have been contaminated by organic solutes, inorganic anions, radionuclides, bacteria and viruses. Gajendra Kumar Tardia "Purification of Wastewater by Metal Oxide Nanoparticles" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-6 | Issue-4 , June 2022, URL: https://www.ijtsrd.com/papers/ijtsrd50327.pdf Paper URL: https://www.ijtsrd.com/other-scientific-research-area/other/50327/purification-of-wastewater-by-metal-oxide-nanoparticles/gajendra-kumar-tardia
Automobile Management System Project Report.pdfKamal Acharya
The proposed project is developed to manage the automobile in the automobile dealer company. The main module in this project is login, automobile management, customer management, sales, complaints and reports. The first module is the login. The automobile showroom owner should login to the project for usage. The username and password are verified and if it is correct, next form opens. If the username and password are not correct, it shows the error message.
When a customer search for a automobile, if the automobile is available, they will be taken to a page that shows the details of the automobile including automobile name, automobile ID, quantity, price etc. “Automobile Management System” is useful for maintaining automobiles, customers effectively and hence helps for establishing good relation between customer and automobile organization. It contains various customized modules for effectively maintaining automobiles and stock information accurately and safely.
When the automobile is sold to the customer, stock will be reduced automatically. When a new purchase is made, stock will be increased automatically. While selecting automobiles for sale, the proposed software will automatically check for total number of available stock of that particular item, if the total stock of that particular item is less than 5, software will notify the user to purchase the particular item.
Also when the user tries to sale items which are not in stock, the system will prompt the user that the stock is not enough. Customers of this system can search for a automobile; can purchase a automobile easily by selecting fast. On the other hand the stock of automobiles can be maintained perfectly by the automobile shop manager overcoming the drawbacks of existing system.
CFD Simulation of By-pass Flow in a HRSG module by R&R Consult.pptxR&R Consult
CFD analysis is incredibly effective at solving mysteries and improving the performance of complex systems!
Here's a great example: At a large natural gas-fired power plant, where they use waste heat to generate steam and energy, they were puzzled that their boiler wasn't producing as much steam as expected.
R&R and Tetra Engineering Group Inc. were asked to solve the issue with reduced steam production.
An inspection had shown that a significant amount of hot flue gas was bypassing the boiler tubes, where the heat was supposed to be transferred.
R&R Consult conducted a CFD analysis, which revealed that 6.3% of the flue gas was bypassing the boiler tubes without transferring heat. The analysis also showed that the flue gas was instead being directed along the sides of the boiler and between the modules that were supposed to capture the heat. This was the cause of the reduced performance.
Based on our results, Tetra Engineering installed covering plates to reduce the bypass flow. This improved the boiler's performance and increased electricity production.
It is always satisfying when we can help solve complex challenges like this. Do your systems also need a check-up or optimization? Give us a call!
Work done in cooperation with James Malloy and David Moelling from Tetra Engineering.
More examples of our work https://www.r-r-consult.dk/en/cases-en/
Event Management System Vb Net Project Report.pdfKamal Acharya
In present era, the scopes of information technology growing with a very fast .We do not see any are untouched from this industry. The scope of information technology has become wider includes: Business and industry. Household Business, Communication, Education, Entertainment, Science, Medicine, Engineering, Distance Learning, Weather Forecasting. Carrier Searching and so on.
My project named “Event Management System” is software that store and maintained all events coordinated in college. It also helpful to print related reports. My project will help to record the events coordinated by faculties with their Name, Event subject, date & details in an efficient & effective ways.
In my system we have to make a system by which a user can record all events coordinated by a particular faculty. In our proposed system some more featured are added which differs it from the existing system such as security.
Quality defects in TMT Bars, Possible causes and Potential Solutions.PrashantGoswami42
Maintaining high-quality standards in the production of TMT bars is crucial for ensuring structural integrity in construction. Addressing common defects through careful monitoring, standardized processes, and advanced technology can significantly improve the quality of TMT bars. Continuous training and adherence to quality control measures will also play a pivotal role in minimizing these defects.
TECHNICAL TRAINING MANUAL GENERAL FAMILIARIZATION COURSEDuvanRamosGarzon1
AIRCRAFT GENERAL
The Single Aisle is the most advanced family aircraft in service today, with fly-by-wire flight controls.
The A318, A319, A320 and A321 are twin-engine subsonic medium range aircraft.
The family offers a choice of engines
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Courier management system project report.pdfKamal Acharya
It is now-a-days very important for the people to send or receive articles like imported furniture, electronic items, gifts, business goods and the like. People depend vastly on different transport systems which mostly use the manual way of receiving and delivering the articles. There is no way to track the articles till they are received and there is no way to let the customer know what happened in transit, once he booked some articles. In such a situation, we need a system which completely computerizes the cargo activities including time to time tracking of the articles sent. This need is fulfilled by Courier Management System software which is online software for the cargo management people that enables them to receive the goods from a source and send them to a required destination and track their status from time to time.
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.