Shielded metal arc welding (SMAW), also known as manual metal arc (MMA) welding or stick welding, is one of world's most popular welding processes due to its versatility and simplicity. It is particularly dominant in maintenance and repair industries and is used extensively in construction of steel structures and industrial fabrication. While its use has declined with expanded use of flux-cored arc welding and gas metal arc welding, SMAW remains popular for its low equipment costs and wide applicability, especially among amateurs and small businesses. SMAW can be used to weld many materials like carbon steel, stainless steel, and cast iron, in any position with proper technique.
Arc welding is type of welding in Manufacturing Processes. Brief Introduction about Arc welding and types of arc welding and their introduction. There are many types of Arc welding available in the market.
Arc welding is type of welding in Manufacturing Processes. Brief Introduction about Arc welding and types of arc welding and their introduction. There are many types of Arc welding available in the market.
It is a type of welding that uses a welding power supply to create an electric arc between an metal stick and the base material to melt the metals at the point-of-contact
Welding process
Arc Welding
Resistance Welding
Oxy fuel Gas Welding
Other Fusion Welding Processes
Solid State Welding
Weld Quality
Weld ability
Design Considerations in Welding
Welding equipment's is the tools used in the welding
The following equipment's used in the welding
1. Power Source (AC or DC)
2. Electrode Holder
3. Welding Cables
4. Ground Clamp
5. Welding Electrodes
6. Welding Helmets & Hand Shield
7. Protective Cloths
8. Finishing tools – Wire brush, Chipping Hammers.
Time Temperature Transformation (TTT) curveIsaac Ayuba M.
In material science, this topic is very essential to understanding the principle of heat treatment of metals. So in studying heat treatment along side this TTT curve will simplify the complexity of heat treatment of metals.
It is a type of welding that uses a welding power supply to create an electric arc between an metal stick and the base material to melt the metals at the point-of-contact
Welding process
Arc Welding
Resistance Welding
Oxy fuel Gas Welding
Other Fusion Welding Processes
Solid State Welding
Weld Quality
Weld ability
Design Considerations in Welding
Welding equipment's is the tools used in the welding
The following equipment's used in the welding
1. Power Source (AC or DC)
2. Electrode Holder
3. Welding Cables
4. Ground Clamp
5. Welding Electrodes
6. Welding Helmets & Hand Shield
7. Protective Cloths
8. Finishing tools – Wire brush, Chipping Hammers.
Time Temperature Transformation (TTT) curveIsaac Ayuba M.
In material science, this topic is very essential to understanding the principle of heat treatment of metals. So in studying heat treatment along side this TTT curve will simplify the complexity of heat treatment of metals.
This topic introduces the methods of irons, steels and cast irons production. It also describes the structure, properties and the usage of irons, steels and cast irons in the engineering field.
This topic relates to polymer structure and types of plastic. It also explains the usage and mechanical properties of thermo plastic, thermosetting plastic and the process of making plastic products.
Chapter 1: Material Structure and Binary Alloy Systemsyar 2604
This is an introduction to material structure and periodic table system. This topic also describes microstructure of the metals and alloys solidification.
Chapter 3: Metal Works, Casting & Heat Treatmentsyar 2604
This topic explains the processes of metal works and casting. It also describes the types and purpose of heat treatment for steels and the effects of heat treatment on mechanical properties of steels.
The discovery of X-rays and the phenomenon of radioactivity and their application to the examination of objects provided the starting point for the advancement of industrial radiography. This technique is one of the most widely used for the detection of internal defects such as voids and porosity. Planar defects can also be detected by radiography with some proper orientation. Radiography is also suitable for detecting changes in material composition, thickness measurements and locating unwanted or defective components hidden from view in an assembled part.
SMAW is one of the basic and most common of all welding processes. this presentation is geared towards helping the general public in understanding the fundamentals of SMAW process. Look out for my next series of publications...
Guide to understanding welding procedure specification (wpsTonni Bruce
this is my private data, i just want to translate some of documents that i just find on the internet into my language to easy to learn, so if anyone have the same native language with me they can use my book.
thanks for all
Germangulf.com, the authorized distributor of Kemppi offers global welding solutions for both demanding industrial applications and ready-to-weld needs. For More Information and enquiry, please contact: welding@german-gulf.com or +971 6 5316171 | Fax: +971 6 5314184
In the modern world of industrialization the wear is eating metal assets worth millions of dollars per year. The wear is in the form of corrosion, erosion, abrasion etc. which occur in the process industries like oil & gas, refineries, cement plants, steel plants, shipping and offshore working structures. The equipments like pressure vessels, heat exchangers, hydro processing reactors which very often work at elevated temperatures face corrosion in the internal diameter.Hastelloy C-276weld overlay on ferrous material is developed for outstanding resistance to wide variety of chemical process environments such as ferric and cupric chlorides, hot contaminated mineral acids, solvents, chlorine and chlorine contained media, both inorganic and organic, dry chlorine, formic and acetic acids, acetic anhydride, sea water and brine solutions.Selection of SMAW is for development of hastalloy C-276 material with SMAW process to use as a weld overlay process at non accessible area & where position is constraint which is not feasible by other processes like ESSC, FCAW, and SAW etc.
The Technological advancements have driven up temperature and pressure serviced in the
petroleum, chemical, pulp, and environmental protection. Industries have increased the possibility of
severe corrosion and wear in process pressure vessels. The industries must upgrade the corrosion and
wear performance of these main important parts .Economic features as a rule will not allow fabricating
components from solid high alloyed materials. As a result it is essential to surface non-alloyed or low
alloy base materials with high-alloy cladding. The submerged arc welding(SAW) and electroslag welding
(ESW) process are appropriate for applying welded deposits over large surface areas by means of strip
electrodes .Both processes are using a granular flux material. A strip electrode, fed continuously, is
liquefied and fused to the substrate. In contrast with other processes it is very effective in spite of the
same equipments used but due to the wide strip used it procures a magnetic flow effect within to rectify it
a magnetic steering device is exercised. After the welding to examine the defects NDT's are carried upon it
Welding is a fabrication process used to join materials, typically metals or thermoplastics, by causing fusion, leading to the creation of a strong, permanent bond. Various welding processes exist, each with its own techniques, applications, and suitability for different materials and conditions. Some of the common welding processes include:
Shielded Metal Arc Welding (SMAW):
Commonly known as "stick welding," it uses a consumable electrode coated with flux to create the weld.
It's versatile and widely used in construction, maintenance, and repair work.
Gas Metal Arc Welding (GMAW/MIG - Metal Inert Gas):
Uses a continuous solid wire electrode and a shielding gas (typically argon or a mix of gases) to protect the weld area from atmospheric contamination.
Generally used in manufacturing, automotive, and construction industries.
Gas Tungsten Arc Welding (GTAW/TIG - Tungsten Inert Gas):
Uses a non-consumable tungsten electrode and a separate filler material if needed.
Often used for thin materials, critical welds, or where precise control is necessary.
Flux-Cored Arc Welding (FCAW):
Similar to MIG welding but uses a tubular wire filled with flux instead of a solid wire and external shielding gas.
Commonly used in heavy equipment manufacturing and construction.
Submerged Arc Welding (SAW):
Involves feeding a continuous, solid filler wire electrode and granular flux over the weld zone.
Ideal for heavy industrial applications due to its high deposition rates.
Resistance Spot Welding (RSW):
Joins metals by applying pressure and passing current through the metals using copper alloy electrodes.
Widely used in automotive manufacturing and sheet metal applications.
Oxy-Fuel Welding (OFW):
Uses fuel gases and oxygen to weld and cut metals.
Still used for maintenance and repair work, though its use has declined in favor of other processes.
Electron Beam Welding (EBW) and Laser Beam Welding (LBW):
Utilize highly focused beams of electrons or lasers to create high-quality welds in precise and delicate applications, often in aerospace or electronics industries.
Each welding method has its advantages and limitations, making certain techniques better suited for specific applications based on factors like material type, thickness, required strength, and the environment in which the welding will be performed.
Welding processes continue to evolve, with advancements in technology improving efficiency, precision, and safety, and newer techniques being developed to cater to specific industrial needs and challenges.
There are numerous welding processes including arc welding, electron beam welding,
friction welding, laser welding, and resistance welding. This article will concentrate on arc
welding, which is the most common technique used to join most steels. Factors affecting
weld quality will be discussed and how to avoid common weld defects will be presented.
Arc welding requires striking a low-voltage, high-current arc between an electrode and the
base metal. The intense heat generated with this arc melts the base metal and allows the
joining of two components. The characteristic of the metal that is being welded and the joint
type (i.e. groove, fillet, etc.) dictates the welding parameters and the procedure that needs to
be followed to obtain a sound weld joint.
Welding process /certified fixed orthodontic courses by Indian dental acad...Indian dental academy
The Indian Dental Academy is the Leader in continuing dental education , training dentists in all aspects of dentistry and offering a wide range of dental certified courses in different formats.
Indian dental academy provides dental crown & Bridge,rotary endodontics,fixed orthodontics,
Dental implants courses.for details pls visit www.indiandentalacademy.com ,or call
00919248678078
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
Using recycled concrete aggregates (RCA) for pavements is crucial to achieving sustainability. Implementing RCA for new pavement can minimize carbon footprint, conserve natural resources, reduce harmful emissions, and lower life cycle costs. Compared to natural aggregate (NA), RCA pavement has fewer comprehensive studies and sustainability assessments.
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
We have compiled the most important slides from each speaker's presentation. This year’s compilation, available for free, captures the key insights and contributions shared during the DfMAy 2024 conference.
HEAP SORT ILLUSTRATED WITH HEAPIFY, BUILD HEAP FOR DYNAMIC ARRAYS.
Heap sort is a comparison-based sorting technique based on Binary Heap data structure. It is similar to the selection sort where we first find the minimum element and place the minimum element at the beginning. Repeat the same process for the remaining elements.
Hierarchical Digital Twin of a Naval Power SystemKerry Sado
A hierarchical digital twin of a Naval DC power system has been developed and experimentally verified. Similar to other state-of-the-art digital twins, this technology creates a digital replica of the physical system executed in real-time or faster, which can modify hardware controls. However, its advantage stems from distributing computational efforts by utilizing a hierarchical structure composed of lower-level digital twin blocks and a higher-level system digital twin. Each digital twin block is associated with a physical subsystem of the hardware and communicates with a singular system digital twin, which creates a system-level response. By extracting information from each level of the hierarchy, power system controls of the hardware were reconfigured autonomously. This hierarchical digital twin development offers several advantages over other digital twins, particularly in the field of naval power systems. The hierarchical structure allows for greater computational efficiency and scalability while the ability to autonomously reconfigure hardware controls offers increased flexibility and responsiveness. The hierarchical decomposition and models utilized were well aligned with the physical twin, as indicated by the maximum deviations between the developed digital twin hierarchy and the hardware.
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
3. 1.1 INTRODUCTION1.1 INTRODUCTION
Shielded metal arc weldingShielded metal arc welding (SMAW)(SMAW), also known as, also known as manualmanual
metal arc (MMA) weldingmetal arc (MMA) welding or informally asor informally as stick weldingstick welding, is a, is a
manual arc welding process that uses a consumable electrodemanual arc welding process that uses a consumable electrode
coated in flux to lay the weld.coated in flux to lay the weld.
An electric current, in the form of either alternating current or directAn electric current, in the form of either alternating current or direct
current from a welding power supply, is used to form an electric arccurrent from a welding power supply, is used to form an electric arc
between the electrode and the metals to be joined. As the weld isbetween the electrode and the metals to be joined. As the weld is
laid, the flux coating of the electrode disintegrates, giving off vaporslaid, the flux coating of the electrode disintegrates, giving off vapors
that serve as a shielding gas and providing a layer of slag, both ofthat serve as a shielding gas and providing a layer of slag, both of
which protect the weld area from atmospheric contamination.which protect the weld area from atmospheric contamination.
Because of the versatility of the process and the simplicity of itsBecause of the versatility of the process and the simplicity of its
equipment and operation, shielded metal arc welding is one of theequipment and operation, shielded metal arc welding is one of the
world's most popular welding processes. It dominates other weldingworld's most popular welding processes. It dominates other welding
processes in the maintenance and repair industry, and though flux-processes in the maintenance and repair industry, and though flux-
cored arc welding is growing in popularity, SMAW continues to becored arc welding is growing in popularity, SMAW continues to be
used extensively in the construction of steel structures and inused extensively in the construction of steel structures and in
industrial fabrication. The process is used primarily to weld iron andindustrial fabrication. The process is used primarily to weld iron and
steels (including stainless steel) but aluminum, nickel and coppersteels (including stainless steel) but aluminum, nickel and copper
alloys can also be welded with this methodalloys can also be welded with this method
4. To strike the electric arc, the electrode is brought into contact with the
workpiece in a short sweeping motion and then pulled away slightly.
This initiates the arc and thus the melting of the workpiece and the
consumable electrode, and causes droplets of the electrode to be
passed from the electrode to the weld pool.
As the electrode melts, the flux covering disintegrates, giving off vapors
that protect the weld area from oxygen and other atmospheric gases. In
addition, the flux provides molten slag which covers the filler metal as it
travels from the electrode to the weld pool. Once part of the weld pool,
the slag floats to the surface and protects the weld from contamination
as it solidifies.
1.2 OPERATION1.2 OPERATION
5. Once hardened, it must be chipped away to reveal the finished
weld. As welding progresses and the electrode melts, the welder
must periodically stop welding to remove the remaining
electrode stub and insert a new electrode into the electrode
holder. This activity, combined with chipping away the slag,
reduce the amount of time that the welder can spend laying the
weld, making SMAW one of the least efficient welding
processes.
SMAW weld area
6. The actual welding technique utilized depends on the electrode,
the composition of the workpiece, and the position of the joint
being welded. The choice of electrode and welding position also
determine the welding speed. Flat welds require the least
operator skill, and can be done with electrodes that melt quickly
but solidify slowly. This permits higher welding speeds. Sloped,
vertical or upside-down welding requires more operator skill, and
often necessitates the use of an electrode that solidifies quickly to
prevent the molten metal from flowing out of the weld pool.
However, this generally means that the electrode melts less
quickly, thus increasing the time required to lay the weld.
7. The most common quality problems associated with SMAW includeThe most common quality problems associated with SMAW include
weld spatter, porosity, poor fusion, shallow penetration, andweld spatter, porosity, poor fusion, shallow penetration, and
crackingcracking. Weld spatter damages its appearance and increases. Weld spatter damages its appearance and increases
cleaning costs. It can be caused by excessively high current, a longcleaning costs. It can be caused by excessively high current, a long
arc, or arc blow, a condition associated with direct currentarc, or arc blow, a condition associated with direct current
characterized by the electric arc being deflected away from the weldcharacterized by the electric arc being deflected away from the weld
pool by magnetic forces.pool by magnetic forces.
Arc blow can also cause porosity in the weld, as can jointArc blow can also cause porosity in the weld, as can joint
contamination, high welding speed, and a long welding arc,contamination, high welding speed, and a long welding arc,
especially when low-hydrogen electrodes are used.especially when low-hydrogen electrodes are used.
Porosity, often not visible without the use of advancedPorosity, often not visible without the use of advanced
nondestructive testing methods, is a serious concern because it cannondestructive testing methods, is a serious concern because it can
potentially weaken the weld.potentially weaken the weld.
Another defect affecting the strength of the weld is poor fusion,Another defect affecting the strength of the weld is poor fusion,
though it is often easily visible. It is caused by low current,though it is often easily visible. It is caused by low current,
contaminated joint surfaces, or the use of an improper electrode.contaminated joint surfaces, or the use of an improper electrode.
1.3 QUALITY1.3 QUALITY
8. Shallow penetration, another detriment to weld strength, can beShallow penetration, another detriment to weld strength, can be
addressed by decreasing welding speed, increasing the current oraddressed by decreasing welding speed, increasing the current or
using a smaller electrode.using a smaller electrode.
Any of these weld-strength-related defects can make the weld proneAny of these weld-strength-related defects can make the weld prone
to cracking, but other factors are involved as well. High carbon, alloyto cracking, but other factors are involved as well. High carbon, alloy
or sulfur content in the base material can lead to cracking,or sulfur content in the base material can lead to cracking,
especially if low-hydrogen electrodes and preheating are notespecially if low-hydrogen electrodes and preheating are not
employed. Furthermore, the workpieces should not be excessivelyemployed. Furthermore, the workpieces should not be excessively
restrained, as this introduces residual stresses into the weld andrestrained, as this introduces residual stresses into the weld and
can cause cracking as the weld cools.can cause cracking as the weld cools.
9. Shielded metal arc welding is one of world's most popular weldingShielded metal arc welding is one of world's most popular welding
processes. Because of its versatility and simplicity, it is particularly dominantprocesses. Because of its versatility and simplicity, it is particularly dominant
in the maintenance and repair industry, and is heavily used in thein the maintenance and repair industry, and is heavily used in the
construction of steel structures and in industrial fabrication.construction of steel structures and in industrial fabrication.
In recent years its use has declined as flux-cored arc welding has expandedIn recent years its use has declined as flux-cored arc welding has expanded
in the construction industry and gas metal arc welding has become morein the construction industry and gas metal arc welding has become more
popular in industrial environments. However, because of the low equipmentpopular in industrial environments. However, because of the low equipment
cost and wide applicability, the process will likely remain popular, especiallycost and wide applicability, the process will likely remain popular, especially
among amateurs and small businesses where specialized weldingamong amateurs and small businesses where specialized welding
processes are uneconomical and unnecessary.processes are uneconomical and unnecessary.
SMAW is often used to weld carbon steel, low and high alloy steel, stainlessSMAW is often used to weld carbon steel, low and high alloy steel, stainless
steel, cast iron, and ductile iron. While less popular for nonferrous materials,steel, cast iron, and ductile iron. While less popular for nonferrous materials,
it can be used on nickel and copper and their alloys and, in rare cases, onit can be used on nickel and copper and their alloys and, in rare cases, on
aluminum. The thickness of the material being welded is bounded on the lowaluminum. The thickness of the material being welded is bounded on the low
end primarily by the skill of the welder, but rarely does it drop below 0.05 inend primarily by the skill of the welder, but rarely does it drop below 0.05 in
(1.5 mm). No upper bound exists: with proper joint preparation and use of(1.5 mm). No upper bound exists: with proper joint preparation and use of
multiple passes, materials of virtually unlimited thicknesses can be joined.multiple passes, materials of virtually unlimited thicknesses can be joined.
Furthermore, depending on the electrode used and the skill of the welder,Furthermore, depending on the electrode used and the skill of the welder,
SMAW can be used in any position.SMAW can be used in any position.
1.4 APPLICATION1.4 APPLICATION
10. Shielded metal arc welding equipment typically consists of aShielded metal arc welding equipment typically consists of a
constant current welding power supply and an electrode, with anconstant current welding power supply and an electrode, with an
electrode holder, a work clamp, and welding cables (also known aselectrode holder, a work clamp, and welding cables (also known as
welding leads) connecting the two.welding leads) connecting the two.
1.5 EQUIPMENT1.5 EQUIPMENT
Schematic illustration of
SMAW.
Also known as stick
welding, because the
electrode is in the
shape of a stick.
11. 1.5 ELECTRODES1.5 ELECTRODES
The choice of electrode for SMAW depends on a number of
factors, including the weld material, welding position and the
desired weld properties. The electrode is coated in a metal
mixture called flux.
Electrode coating has the following basic functions:
- to improve the arc stability.
- to generate gases to act as a shield against the surrounding
atmosphere in order to prevent weld contamination.
- to control the rate at which the electrode melts.
- to act as a flux to protect the weld against the formation of
oxides, nitrides and other inclusion and to protect molten –
weld pool.
- to add alloying elements to the weld zone to enhance the
properties of the joint.
12.
13. 2. gas METaL2. gas METaL
aRC WELDINgaRC WELDINg
(gMaW)(gMaW)
14. Gas metal arc welding (GMAW), sometimes referred to by its
subtypes metal inert gas (MIG) welding or metal active gas
(MAG) welding, is a semi-automatic or automatic arc welding
process in which a continuous and consumable wire electrode
and a shielding gas are fed through a welding gun. A constant
voltage, direct current power source is most commonly used with
GMAW, but constant current systems, as well as alternating
current alternating current, can be used. There are four primary
methods of metal transfer in GMAW, called globular, short-
circuiting, spray, and pulsed-spray, each of which has distinct
properties and corresponding advantages and limitations.
GMAW is the most common industrial welding process, preferred
for its versatility, speed and the relative ease of adapting the
process to robotic automation. The automobile industry in particular
uses GMAW welding almost exclusively. Unlike welding processes
that do not employ a shielding gas, such as shielded metal arc
welding, it is rarely used outdoors or in other areas of air volatility.
2.1.1 INTRODUCTION (MIG)2.1.1 INTRODUCTION (MIG)
15. To perform gas metal arc welding, the basic necessary equipment is a
welding gun, a wire feed unit, a welding power supply, an electrode
wire, and a shielding gas supply. Shielding gases are inert or semi-inert
gases that are commonly used in several welding processes, most
notably gas metal arc welding and gas tungsten arc welding. ...
Wire feed unit for GMAW GMAW torch nozzle
(1) Torch handle
(2) Molded phenolic
dielectric
(3) Shielding gas
nozzle
(4) Contact tip
(5) Nozzle output
face
2.1.2 EQUIPMENT2.1.2 EQUIPMENT
16. The typical GMAW welding gun has a number of key parts—a control
switch, a contact tip, a power cable, a gas nozzle, an electrode conduit
and liner, and a gas hose. The control switch, or trigger, when pressed
by the operator, initiates the wire feed, electric power, and the
shielding gas flow, causing an electric arc to be struck. The contact tip,
normally made of copper and sometimes chemically treated to reduce
spatter, is connected to the welding power source through the power
cable and transmits the electrical energy to the electrode while
directing it to the weld area. It must be firmly secured and properly
sized, since it must allow the passage of the electrode while
maintaining an electrical contact. Before arriving at the contact tip, the
wire is protected and guided by the electrode conduit and liner, which
help prevent buckling and maintain an uninterrupted wire feed. The
gas nozzle is used to evenly direct the shielding gas into the welding
zone—if the flow is inconsistent, it may not provide adequate
protection of the weld area. Larger nozzles provide greater shielding
gas flow, which is useful for high current welding operations, in which
the size of the molten weld pool is increased. The gas is supplied to
the nozzle through a gas hose, which is connected to the tanks of
shielding gas.
17. Alternating current is rarely used with GMAW; instead, direct current is
employed and the electrode is generally positively charged. Since the
anode tends to have a greater heat concentration, this results in faster
melting of the feed wire, which increases weld penetration and welding
speed. The polarity can be reversed only when special emissive-coated
electrode wires are used, but since these are not popular, a negatively
charged electrode is rarely employed.
18. Electrode selection is based primarily on the composition of the metal
being welded, but also on the process variation being used, the joint
design, and the material surface conditions. The choice of an electrode
strongly influences the mechanical properties of the weld area, and is a
key factor in weld quality. In general, the finished weld metal should have
mechanical properties similar to those of the base material, with no defects
such as discontinuities, entrained contaminants, or porosity, within the
weld. To achieve these goals a wide variety of electrodes exist. All
commercially available electrodes contain deoxidizing metals such as
silicon, manganese, titanium and aluminum in small percentages to help
prevent oxygen porosity, and some contain denitriding metals such as
titanium and zirconium to avoid nitrogen porosity. Depending on the
process variation and base material being used, the diameters of the
electrodes used in GMAW typically range from 0.7 to 2.4 mm (0.028–
0.095 in), but can be as large as 4 mm (0.16 in). The smallest electrodes,
generally up to 1.14 mm (0.045 in) are associated with the short-circuiting
metal transfer process, while the most common spray-transfer process
mode electrodes are usually at least 0.9 mm (0.035 in).
2.1.3 ELECTRODE2.1.3 ELECTRODE
19. 2.1.4 SHIELDING GAS2.1.4 SHIELDING GAS
Shielding gases are necessary for gas metal arc welding to protect the
welding area from atmospheric gases such as nitrogen and oxygen, which
can cause fusion defects, inadequate weld penetration (argon) or cause an
erratic arc and encourage spatter (with helium).
Argon is also commonly mixed with other gases, such as oxygen, helium,
hydrogen and nitrogen. The addition of up to 5% oxygen can be helpful in
welding stainless steel or in very thin gauge materials, however, in most
applications carbon dioxide is preferred. Increased oxygen makes the
shielding gas oxidize the electrode, which can lead to porosity in the
deposit if the electrode does not contain sufficient deoxidizers. Argon-
helium mixtures are completely inert, and can be used on nonferrous
materials.
Shielding gas mixtures of three or more gases are also available.
claiming to improve weld quality.
20. GMAW requires only that the operator guide the welding gun with proper
position and orientation along the area being welded. Keeping a consistent
contact tip-to-work distance (the stickout distance) is important, because a
long stickout distance can cause the electrode to overheat and will also
waste shielding gas. Stickout distance varies for different GMAW weld
processes and applications. The position of the end of the contact tip to the
gas nozzle are related to the stickout distance and also varies with transfer
type and application. The orientation of the gun is also important—it should
be held so as to bisect the angle between the workpieces; that is, at 45
degrees for a fillet weld and 90 degrees for welding a flat surface. The travel
angle or lead angle is the angle of the torch with respect to the direction of
travel, and it should generally remain approximately vertical. However, the
desirable angle changes somewhat depending on the type of shielding gas
used—with pure inert gases, the bottom of the torch is out often slightly in
front of the upper section, while the opposite is true when the welding
atmosphere is carbon dioxide.
2.1.5 TECHNIQUE2.1.5 TECHNIQUE
21. 2.1.6 QUALITY2.1.6 QUALITY
Two of the most prevalent quality problems in GMAW are dross and
porosity. If not controlled, they can lead to weaker, less ductile welds.
Dross, a mass of solid impurities floating on a molten metal bath, is an
especially common problem in aluminum GMAW welds, normally coming
from particles of aluminum oxide or aluminum nitride present in the
electrode or base materials. Electrodes and workpieces must be brushed
with a wire brush or chemically treated to remove oxides on the surface.
Any oxygen in contact with the weld pool, whether from the atmosphere or
the shielding gas, causes dross as well. As a result, sufficient flow of inert
shielding gases is necessary, and welding in volatile air should be avoided.
In GMAW the primary cause of porosity is gas entrapment in the weld
pool, which occurs when the metal solidifies before the gas escapes.
The gas can come from impurities in the shielding gas or on the
workpiece.
22. 2.2.1 INTRODUCTION (TIG)2.2.1 INTRODUCTION (TIG)
Gas tungsten arc welding (GTAW), also known as tungsten inert gas
(TIG) welding, is an arc welding process that uses a nonconsumable
tungsten electrode to produce the weld. The weld area is protected from
atmospheric contamination by a shielding gas (usually an inert gas such
as argon), and a filler metal is normally used, though some welds, known
as autogenous welds, do not require it.
GTAW is most commonly used to weld thin sections of stainless steel
and light metals such as aluminum, magnesium and copper alloys.
The process grants the operator greater control over the weld than
competing procedures such as shielded metal arc welding and gas metal
arc welding, allowing for stronger, higher quality welds. However, GTAW
is comparatively more complex and difficult to master, and furthermore, it
is significantly slower than most other welding techniques.
23. 2.2.2 OPERATION2.2.2 OPERATION
Manual gas tungsten arc welding is often considered the most difficult of
all the welding processes commonly used in industry. Because the
welder must maintain a short arc length, great care and skill are required
to prevent contact between the electrode and the workpiece. Unlike most
other welding processes, GTAW normally requires two hands, since most
applications require that the welder manually feed a filler metal into the
weld area with one hand while manipulating the welding torch in the
other. However, some welds combining thin materials (known as
autogenous or fusion welds) can be accomplished without filler metal;
most notably edge, corner and butt joints.
24. To strike the welding arc, a high frequency generator provides a path for the
welding current through the shielding gas, allowing the arc to be struck
when the separation between the electrode and the workpiece is
approximately 1.5–3 mm (0.06–0.12 in). Once the arc is struck, the welder
moves the torch in a small circle to create a welding pool, the size of which
depends on the size of the electrode and the amount of current. While
maintaining a constant separation between the electrode and the
workpiece, the operator then moves the torch back slightly and tilts it
backward about 10–15 degrees from vertical. Filler metal is added manually
to the front end of the weld pool as it is needed.
GTAW can use a positive direct current, negative direct current or an
alternating current, depending on the power supply set up. A negative direct
current from the electrode causes a stream of electrons to collide with the
surface, generating large amounts of heat at the weld region. This creates a
deep, narrow weld. In the opposite process where the electrode is connected
to the positive power supply terminal, positively charged ions flow from the
tip of the electrode instead, so the heating action of the electrons is mostly
on the electrode. This mode also helps to remove oxide layers from the
surface of the region to be welded, which is good for metals such as
aluminum or magnesium. A shallow, wide weld is produced from this mode,
with minimum heat input.
25. 2.2.3 APPLICATIONS2.2.3 APPLICATIONS
The aerospace industry is one of the primary users of gas tungsten arc
welding, the process is used in a number of other areas. Many industries
use GTAW for welding thin workpieces, especially nonferrous metals.
It is used extensively in the manufacture of space vehicles, and is also
frequently employed to weld small-diameter, thin-wall tubing such as
those used in the bicycle industry.
In addition, GTAW is often used to make root or first pass welds for piping
of various sizes.
In maintenance and repair work, the process is commonly used to repair
tools and dies, especially components made of aluminum and
magnesium. Because the weld metal is not transferred directly across the
electric arc like most open arc welding processes, a vast assortment of
welding filler metal is available to the welding engineer. In fact, no other
welding process permits the welding of so many alloys in so many product
configurations
26. 2.2.4 QUALITY2.2.4 QUALITY
Engineers prefer GTAW welds because of its low-hydrogen properties and
the match of mechanical and chemical properties with the base material.
Maximum weld quality is assured by maintaining the cleanliness of the
operation—all equipment and materials used must be free from oil, moisture,
dirt and other impurities, as these cause weld porosity and consequently a
decrease in weld strength and quality.
Low heat input, caused by low welding current or high welding speed,
can limit penetration and cause the weld bead to lift away from the
surface being welded. If there is too much heat input, however, the weld
bead grows in width while the likelihood of excessive penetration and
spatter increase. Additionally, if the welder holds the welding torch too
far from the workpiece, shielding gas is wasted and the appearance of
the weld worsens.
If the amount of current used exceeds the capability of the electrode,
tungsten inclusions in the weld may result. Known as tungsten spitting, it can
be identified with radiography and prevented by changing the type of
electrode or increasing the electrode diameter. if the electrode is not well
protected by the gas shield or the operator accidentally allows it to contact
the molten metal, it can become dirty or contaminated.
27. 2.2.5 EQUIPMENT2.2.5 EQUIPMENT
The equipment required for the gas tungsten arc welding operation
includes a welding torch utilizing a nonconsumable tungsten electrode,
a constant-current welding power supply and a shielding gas source.
Gas tungsten arc welding uses a constant current power source,
meaning that the current (and thus the heat) remains relatively constant,
even if the arc distance and voltage change. This is important because
most applications of GTAW are manual or semiautomatic, requiring that
an operator hold the torch. Maintaining a suitably steady arc distance is
difficult if a constant voltage power source is used instead, since it can
cause dramatic heat variations and make welding more difficult.
28. The preferred polarity of the GTAW system depends largely on the type of
metal being welded. Direct current with a negatively charged electrode
(DCEN) is often employed when welding steels, nickel, titanium and other
metals. It can also be used in automatic GTA welding of aluminum or
magnesium when helium is used as a shielding gas.
The negatively charged electrode generates heat by emitting electrons which
travel across the arc, causing thermal ionization of the shielding gas and
increasing the temperature of the base material. The ionized shielding gas
flows toward the electrode, not the base material. Direct current with a
positively charged electrode (DCEP) is less common, and is used primarily
for shallow welds since less heat is generated in the base material. Instead
of flowing from the electrode to the base material, as in DCEN, electrons go
the other direction, causing the electrode to reach very high temperatures.
To help it maintain its shape and prevent softening, a larger electrode is
often used.
29. Advantages
- Concentrated Arc - Permits pin point control of heat input to the
workpiece
resulting in a narrow heat-affected zone
- No Slag - No requirement for flux, therefore no slag to obscure the
welder’s vision of the molten weld pool
- No Sparks or Spatter - No transfer of metal across the arc. No molten
globules of spatter to contend with and no sparks produced if material
being welded is free of contaminants
- Little Smoke or Fumes - Compared to other arc-welding processes like
stick or flux-cored welding, few fumes are produced. The base metals
being welded may contain coatings or elements such as lead, zinc,
copper, nickel that may produce hazardous fumes, however
- Welds more metals and metal alloys than any other process
- Good for welding thin material.
2.2.5 ADVANTAGES &2.2.5 ADVANTAGES &
DISADVANTAGESDISADVANTAGES
30. Disadvantages
-Slower travel speeds than other processes
-Lower filler metal deposition rates
-Hand-eye coordination is a required skill
-Brighter UV rays than other processes
-Equipment costs can be higher than other processes
-Concentrations of shielding gas may build up and displace oxygen
when welding in confined areas
32. 3.1 INTRODUCTION3.1 INTRODUCTION
InIn submerged-arc weldingsubmerged-arc welding (SAW), the weld arc is shielded by a(SAW), the weld arc is shielded by a
granular fluxgranular flux consisting of lime, silica, manganese oxide,consisting of lime, silica, manganese oxide,
calcium fluoride, and other compounds.calcium fluoride, and other compounds.
The flux is fed into the weld zone from a hopper by gravity flowThe flux is fed into the weld zone from a hopper by gravity flow
through a nozzle.through a nozzle.
The thick layer of flux completely covers the molten metal.The thick layer of flux completely covers the molten metal.
It prevents spatter and sparks and suppresses the intenseIt prevents spatter and sparks and suppresses the intense
ultraviolet radiation and fumes characteristic of the SMAWultraviolet radiation and fumes characteristic of the SMAW
process.process.
34. The flux acts as a thermal insulator by promoting deep penetrationThe flux acts as a thermal insulator by promoting deep penetration
of heat into the workpiece.of heat into the workpiece.
The consumable electrode is fed automatically through a tube calledThe consumable electrode is fed automatically through a tube called
welding gun.welding gun.
Electrical currents range between 300 & 2000 A.Electrical currents range between 300 & 2000 A.
Because the flux is gravity fed, the SAW process is limited largely toBecause the flux is gravity fed, the SAW process is limited largely to
welds in a flat or horizontal position.welds in a flat or horizontal position.
Circular welds can be made on pipes and cylinder by rotating theCircular welds can be made on pipes and cylinder by rotating the
workpiece.workpiece.
The process is automated and is used to weld variety of carbon andThe process is automated and is used to weld variety of carbon and
alloy steel and stainless-steel sheets or plates at speeds as high asalloy steel and stainless-steel sheets or plates at speeds as high as
5 m/min.5 m/min.
Weld quality is very high – good toughness, ductility and uniformityWeld quality is very high – good toughness, ductility and uniformity
of properties.of properties.
SAW process provides very high welding productivity, depositing 4SAW process provides very high welding productivity, depositing 4
to 10 times the amount of weld metal per hour as the SMAWto 10 times the amount of weld metal per hour as the SMAW
process.process.
Suitable for thick-plate welding for shipbuilding and pressureSuitable for thick-plate welding for shipbuilding and pressure
vessels.vessels.
35. Advantages of SAWAdvantages of SAW
-- High deposition rates (over 100 lb/h (45 kg/h) have been reported);High deposition rates (over 100 lb/h (45 kg/h) have been reported);
-- High operating factors in mechanized applications;High operating factors in mechanized applications;
-- Deep weld penetration;Deep weld penetration;
-- Sound welds are readily made (with good process design andSound welds are readily made (with good process design and
control);control);
-- High speed welding of thin sheet steels at over 100 in/min (2.5High speed welding of thin sheet steels at over 100 in/min (2.5
m/min) is possible;m/min) is possible;
- Minimal welding fume or arc light is emitted.Minimal welding fume or arc light is emitted.
Limitations of SAWLimitations of SAW
- Limited to ferrous (steel or stainless steels) and some nickel based- Limited to ferrous (steel or stainless steels) and some nickel based
alloys;alloys;
- Normally limited to the 1F, 1G, and 2F positions;- Normally limited to the 1F, 1G, and 2F positions;
- Normally limited to long straight seams or rotated pipes or vessels;- Normally limited to long straight seams or rotated pipes or vessels;
- Requires relatively troublesome flux handling systems;- Requires relatively troublesome flux handling systems;
- Flux and slag residue can present a health & safety issue;- Flux and slag residue can present a health & safety issue;
- Requires inter-pass and post weld slag removal.- Requires inter-pass and post weld slag removal.