Hands on lab_instruction
•
0 likes•64 views
This document outlines three packet tracer activities to configure OSPF routing between three routers: Lab_A, Lab_B, and Lab_C. The first activity has students enable the OSPF process on each router with different process IDs. The second activity has them configure OSPF network statements to establish routing. The third activity provides commands to verify OSPF neighbor relationships, routes, and interface settings. Completing all activities will allow the routers to exchange routes via OSPF.
Report
Share
Report
Share
Download to read offline
Recommended
Route Redistribution
Redistribution is necessary when routing protocols connect and must pass routes between the two.
Route Redistribution involves placing the routes learned from one routing domain, such as RIP, into
another routing domain, such as EIGRP.
While running a single routing protocol throughout your entire IP internetwork is desirable, multiprotocol routing is common for a number of reasons, such as company mergers, multiple departments
managed by multiple network administrators, and multi-vendor environments. Running different
routing protocols is often part of a network design.
Eincop Netwax Lab: Redistribution
The document provides instructions for a lab on route redistribution between OSPF, EIGRP and RIP routing protocols. It involves configuring the routing protocols on various routers as specified in the topology, including redistributing routes between protocols. It also requires summarizing loopback routes between areas and protocols.
NE_expt4
1) The document describes an experiment to use a null 0 interface to avoid a routing loop.
2) The network diagram shows routers R1, R2, and R3 connected, where R3 is an ISP backbone router, R1 is an ISP router, and R2 is a customer router using addresses from the 192.168.0.0/24 block.
3) When pinging an unused address on the 192.168.0.0/24 block from R3, a timeout occurs due to a loop between R1 and R2.
Buzzer - Suneel and Mayank
This document describes the design and implementation of a buzzer system for quiz competitions using NI LabVIEW and a NI MyRIO-1900 microcontroller. The system records the response times of two players when they press their buttons and identifies the fastest player by comparing the recorded times. The logic is implemented using LabVIEW block diagrams with timers, comparators, and conditional logic. Hardware connections are made from the microcontroller ports to buttons and buzzers. The system ensures only one player can respond for each question and identifies the fastest player in less than one microsecond.
Eincop Netwax Lab: Lab 1 static route
The document describes setting up static routes on 7 routers (R1-R7) to allow connectivity between all routers and PCs in a network topology. It involves configuring IP addresses and static routes on each router's interfaces according to the topology diagram, so that each router has a route to every other subnet and can ping all other routers and PCs.
Ccn pv7 route_lab2-1_eigrp-load-balancing_student
The document describes a lab that explores EIGRP load balancing capabilities. The objectives are to configure EIGRP on three routers, examine the EIGRP topology table, and verify equal-cost and unequal-cost load balancing. Initial configurations are provided to set up loopback interfaces and serial links between the routers. EIGRP is then enabled on two routers and debugging commands are used to observe route installation.
Nxll21 ospf filtering & summarization
1. The document provides instructions for configuring OSPF routing, filtering LSAs, and summarizing routes between OSPF areas on a network with multiple routers.
2. Tasks include configuring OSPF on each router, filtering routes between areas, redistributing EIGRP routes into OSPF, and using prefix lists and route summarization.
3. The solution shows the OSPF and redistribution configurations needed on each router to implement the requested tasks and filters.
Eincop Netwax Lab: EIGRP iii
1. The document describes configuring EIGRP routing on a network topology. This includes configuring EIGRP routing processes and interfaces, modifying timers, enabling authentication, adjusting metrics, ensuring all routes are learned, implementing route summarization, and filtering routes.
2. Key tasks are configuring EIGRP routing processes on each router with associated networks, changing timers on EIGRP process 200, enabling MD5 authentication between R4 and R5, adjusting metrics for EIGRP 100, redistributing between EIGRP processes, and summarizing loopback routes on R5 and R7.
3. The solution provides the configuration commands needed to complete each task, such as enabling EIGRP routing on
Recommended
Route Redistribution
Redistribution is necessary when routing protocols connect and must pass routes between the two.
Route Redistribution involves placing the routes learned from one routing domain, such as RIP, into
another routing domain, such as EIGRP.
While running a single routing protocol throughout your entire IP internetwork is desirable, multiprotocol routing is common for a number of reasons, such as company mergers, multiple departments
managed by multiple network administrators, and multi-vendor environments. Running different
routing protocols is often part of a network design.
Eincop Netwax Lab: Redistribution
The document provides instructions for a lab on route redistribution between OSPF, EIGRP and RIP routing protocols. It involves configuring the routing protocols on various routers as specified in the topology, including redistributing routes between protocols. It also requires summarizing loopback routes between areas and protocols.
NE_expt4
1) The document describes an experiment to use a null 0 interface to avoid a routing loop.
2) The network diagram shows routers R1, R2, and R3 connected, where R3 is an ISP backbone router, R1 is an ISP router, and R2 is a customer router using addresses from the 192.168.0.0/24 block.
3) When pinging an unused address on the 192.168.0.0/24 block from R3, a timeout occurs due to a loop between R1 and R2.
Buzzer - Suneel and Mayank
This document describes the design and implementation of a buzzer system for quiz competitions using NI LabVIEW and a NI MyRIO-1900 microcontroller. The system records the response times of two players when they press their buttons and identifies the fastest player by comparing the recorded times. The logic is implemented using LabVIEW block diagrams with timers, comparators, and conditional logic. Hardware connections are made from the microcontroller ports to buttons and buzzers. The system ensures only one player can respond for each question and identifies the fastest player in less than one microsecond.
Eincop Netwax Lab: Lab 1 static route
The document describes setting up static routes on 7 routers (R1-R7) to allow connectivity between all routers and PCs in a network topology. It involves configuring IP addresses and static routes on each router's interfaces according to the topology diagram, so that each router has a route to every other subnet and can ping all other routers and PCs.
Ccn pv7 route_lab2-1_eigrp-load-balancing_student
The document describes a lab that explores EIGRP load balancing capabilities. The objectives are to configure EIGRP on three routers, examine the EIGRP topology table, and verify equal-cost and unequal-cost load balancing. Initial configurations are provided to set up loopback interfaces and serial links between the routers. EIGRP is then enabled on two routers and debugging commands are used to observe route installation.
Nxll21 ospf filtering & summarization
1. The document provides instructions for configuring OSPF routing, filtering LSAs, and summarizing routes between OSPF areas on a network with multiple routers.
2. Tasks include configuring OSPF on each router, filtering routes between areas, redistributing EIGRP routes into OSPF, and using prefix lists and route summarization.
3. The solution shows the OSPF and redistribution configurations needed on each router to implement the requested tasks and filters.
Eincop Netwax Lab: EIGRP iii
1. The document describes configuring EIGRP routing on a network topology. This includes configuring EIGRP routing processes and interfaces, modifying timers, enabling authentication, adjusting metrics, ensuring all routes are learned, implementing route summarization, and filtering routes.
2. Key tasks are configuring EIGRP routing processes on each router with associated networks, changing timers on EIGRP process 200, enabling MD5 authentication between R4 and R5, adjusting metrics for EIGRP 100, redistributing between EIGRP processes, and summarizing loopback routes on R5 and R7.
3. The solution provides the configuration commands needed to complete each task, such as enabling EIGRP routing on
Eincop Netwax Lab: Site 2 Site VPN with Routing Protocols
This document provides instructions for configuring routing protocols and a site-to-site VPN between HQ and BR1 networks. The tasks include: 1) configuring EIGRP and RIP routing with redistribution to ensure HQ_R2 learns all routes, 2) enabling MD5 authentication on EIGRP 200, 3) establishing an IPsec VPN between HQ and BR1 to permit access only to BR1 loopback addresses from HQ_R2, and 4) summarizing the BR1 loopback routes into OSPF area 0 on BR1.
Nxll28 ospf iii
1. The document describes tasks for configuring OSPF routing on a network topology.
2. Key configurations include enabling OSPF on each router, configuring authentication for Area 1, summarizing loopback routes on R4, and preventing Area 3 routers from receiving routes from other areas.
3. PAT is configured on routers R1 and R11 to allow traffic from multiple private networks to use a single public IP address.
Eincop Netwax Lab: HSRP (Hot Standby Router Protocol)
This document outlines the steps to configure HSRP (Hot Standby Router Protocol) on two multi-layer switches (MLS1 and MLS2) including: configuring IP addresses, EIGRP routing, web server and NTP server, setting MLS1 as the active router, tracking the state of interfaces, using HSRP for load balancing between the routers, and enabling NAT on the border router for internal traffic.
Nxll11 bgp
The document provides the configuration steps for a lab exercise on BGP. The steps include:
1. Configuring IBGP and EBGP neighborships between routers as shown in the topology diagram using loopback addresses.
2. Advertising loopback networks in BGP to ensure all routers have the routing information.
3. Configuring route reflectors to reduce the number of neighbor relationships needed.
4. Setting preferences for best paths between routers for certain networks.
I pv6 ospfv3 case study
This document illustrates configuring stub, totally stubby, and NSSA areas in OSPFv3. Three routers are configured with OSPFv3, with R1 and R3 in area 0 and R1 and R2 in area 12. Under normal OSPFv3 operation, R2 receives all routes. Configuring area 12 as a stub area causes R2 to only receive the default route and internal OSPF routes. Configuring it as a totally stubby area causes R2 to only receive the default route. Configuring it as an NSSA area causes R2 to only receive intra-area and inter-area OSPF routes.
Usage, Performance and Future Of PL1 at NRB Benoit Ebner
When Peter Elderon visited NRB to present the evolution of PL1, Benoit Ebner made this presentation on how this programmation language is used at NRB.
Nxll25 hsrp with failover
1. The document describes configuring high availability routing between two firewalls (ASA1 and ASA2) using failover, and between two routers (MLS3 and R2) using HSRP.
2. It provides configuration examples for failover on the ASAs, HSRP on MLS3 and R2, PAT on the ASA and R2, and EIGRP routing between the ASA and MLS3.
3. It also specifies default gateways for different PCs to reach R1 via the active HSRP router.
Nxll12 zone based firewall
The document describes tasks for configuring a zone-based firewall on Router 1:
1. Create an inside and outside zone on Router 1's interfaces; apply an inspect policy between the zones to allow necessary traffic.
2. Configure R2 to ping R3 by name by adding DNS and host entries.
3. Configure R2 to copy a file from R4's HTTP server using the file path and name.
4. Configure R2 as the NTP server and have the other routers synchronize to it after applying necessary firewall policies.
Nxll17 dynamic routing with asa
The document describes the steps to configure dynamic routing, site-to-site VPN, and network access between devices in a lab topology. The tasks include: 1) Configuring IP addresses and dynamic routing protocols on routers and firewalls, 2) Establishing connectivity between all devices, 3) Implementing NAT and VPN services on the firewalls to allow communication between specified subnets, and 4) Opening a non-standard port for remote access between two routers via one of the firewalls.
Nxll09 access list
This document provides instructions for completing 12 tasks to configure access control lists on routers. The tasks include configuring IP addresses, inter-VLAN routing, EIGRP routing, DNS, Telnet/SSH access, and ACLs to restrict traffic between VLANs and access to websites based on the VLAN. Detailed configuration steps are provided for each router to implement the access controls and routing as outlined in the tasks.
Nxll26 bgp ii
1. The document describes the configuration steps for a lab exercise involving BGP routing. It includes tasks to configure IP addresses, IBGP, HSRP, servers, and BGP routing on multiple routers as shown in the given topology diagram.
2. Key steps are to configure IBGP between routers R1-R4, HSRP between R5-R6, servers on R6, and BGP routing between all routers as specified in the tasks and topology, including IBGP, EBGP, route reflectors, and BGP confederations.
3. The goal is to verify connectivity between loopbacks and servers across the different BGP and IBGP domains as configured.
Nxll19 vrrp (virtual router redundancy protocol)
The document describes configuring VRRP (Virtual Router Redundancy Protocol) on routers R1 and R2. It involves:
1. Configuring R1 as the master for VRRP group 1 using virtual IP 10.0.0.254 and authentication.
2. Configuring R2 as the master for load-balanced VRRP group 2 using virtual IP 10.0.0.193 and a different authentication string.
3. Enabling tracking on both routers so that the priority of the backup router decreases if the route to the opposite network fails, allowing it to take over as master.
Nxll23 i pv6
The document provides instructions for configuring IPv6 on a network topology. It includes tasks to configure IPv6 addresses on routers, configure Frame-Relay over IPv6, assign IPv6 addresses to routers through autoconfiguration, and configure OSPF routing between the routers.
Nxll10 v lan and trunking
The document describes the tasks and solution for a lab on VLANs and trunking. The tasks are to: 1) Configure IP addresses as shown in the topology, 2) Create DHCP servers for VLANs 10 and 20, 3) Configure SW1 as the VTP server and the others as clients with the domain "netwaxlab.com", 4) Ensure PCs get IP addresses via DHCP, and 5) Allow communication between PCs 9 and 10 which have different IPs on the same VLAN. The solution describes the configurations needed on the switches to accomplish these tasks.
Configuration of Smtp Server On CentOS 8
This document provides instructions for configuring an SMTP server on CentOS 8, including installing Postfix and Dovecot, configuring configuration files like main.cf, master.cf, and firewall rules to allow access to ports 25, 465, and 587 for SMTP, SSL, and submission protocols. Key steps are installing Postfix and Dovecot packages, enabling and starting services, editing configuration files to set mail locations and UIDL formats, and opening required ports in the firewall.
Nxll18 vpn (s2 s gre & dmvpn)
1. The document describes configuring IP addresses, DNS, a site-to-site GRE VPN between routers R5 and R6, and a DMVPN network between routers R1, R2, and R3.
2. For the GRE VPN, ISAKMP and IPsec are configured on R5 and R6 using a preshared key of "netwaxlab" to secure the GRE tunnel.
3. For the DMVPN, R1 is configured as a hub router and R2 and R3 as spoke routers. ISAKMP and IPsec are configured using a preshared key of "netwaxlab" to secure the GRE tunnels between the routers.
Day 11 eigrp
http://www.cyberintelligents.in
info@cyberintelligents.in
https://www.facebook.com/cyberintelligents
https://in.linkedin.com/in/cyberintelligents/en
https://cyberintelligents.wordpress.com/
http://cyberintelligent.blogspot.in
+91 9876162698 +919988288019
http://trainingcyberintelligents.blogspot.com
https://cyberintelligentsnews.wordpress.com/
Nxll16 basic asa v8.2
The document provides instructions for configuring an ASA firewall to:
1. Configure security levels and interfaces for DMZ and DMZ1 subnets.
2. Enable ping access between the DMZ and DMZ1 interfaces.
3. Restrict telnet access to the ASA to only the R2 host.
4. Enable SSH access to the ASA from the ISP subnet only.
5. Apply PAT for the Inside, DMZ and DMZ1 interfaces.
6. Allow the ISP to telnet to the R2 host using port 2487.
Eincop Netwax Lab: EIGRP ii
1. The document describes configuring EIGRP routing on a network topology. This includes configuring EIGRP routing processes and interfaces, adjusting EIGRP timers, enabling authentication, setting metric weights, redistributing routes between EIGRP processes, summarizing routes, and filtering routes.
Cisco labs practical4
This document provides instructions for configuring OSPF routing between routers. Key steps include:
1. Configure IP addresses and interfaces on the routers.
2. Configure OSPF routing process on each router to advertise networks in area 0. This includes adding loopback interfaces for stability.
3. Test connectivity between routers and hosts by pinging interfaces. Troubleshoot any issues until connectivity is established across the network.
Lab 9 instructions
This document describes configuring a basic single-area OSPFv2 network. It includes the topology diagram and addressing tables, and steps to build the network, configure OSPF routing on each router with area 0, and verify OSPF neighbor relationships and routing tables. It also provides sample outputs of show commands to check OSPF settings and interfaces.
Huawei ARG3 Router How To - Troubleshooting OSPF: Netmask mismatch
This third lesson about OSPF troubleshooting will be focused on “Netmask mismatch”. We will isolate the problem and we will correct the configuration.
More Related Content
What's hot
Eincop Netwax Lab: Site 2 Site VPN with Routing Protocols
This document provides instructions for configuring routing protocols and a site-to-site VPN between HQ and BR1 networks. The tasks include: 1) configuring EIGRP and RIP routing with redistribution to ensure HQ_R2 learns all routes, 2) enabling MD5 authentication on EIGRP 200, 3) establishing an IPsec VPN between HQ and BR1 to permit access only to BR1 loopback addresses from HQ_R2, and 4) summarizing the BR1 loopback routes into OSPF area 0 on BR1.
Nxll28 ospf iii
1. The document describes tasks for configuring OSPF routing on a network topology.
2. Key configurations include enabling OSPF on each router, configuring authentication for Area 1, summarizing loopback routes on R4, and preventing Area 3 routers from receiving routes from other areas.
3. PAT is configured on routers R1 and R11 to allow traffic from multiple private networks to use a single public IP address.
Eincop Netwax Lab: HSRP (Hot Standby Router Protocol)
This document outlines the steps to configure HSRP (Hot Standby Router Protocol) on two multi-layer switches (MLS1 and MLS2) including: configuring IP addresses, EIGRP routing, web server and NTP server, setting MLS1 as the active router, tracking the state of interfaces, using HSRP for load balancing between the routers, and enabling NAT on the border router for internal traffic.
Nxll11 bgp
The document provides the configuration steps for a lab exercise on BGP. The steps include:
1. Configuring IBGP and EBGP neighborships between routers as shown in the topology diagram using loopback addresses.
2. Advertising loopback networks in BGP to ensure all routers have the routing information.
3. Configuring route reflectors to reduce the number of neighbor relationships needed.
4. Setting preferences for best paths between routers for certain networks.
I pv6 ospfv3 case study
This document illustrates configuring stub, totally stubby, and NSSA areas in OSPFv3. Three routers are configured with OSPFv3, with R1 and R3 in area 0 and R1 and R2 in area 12. Under normal OSPFv3 operation, R2 receives all routes. Configuring area 12 as a stub area causes R2 to only receive the default route and internal OSPF routes. Configuring it as a totally stubby area causes R2 to only receive the default route. Configuring it as an NSSA area causes R2 to only receive intra-area and inter-area OSPF routes.
Usage, Performance and Future Of PL1 at NRB Benoit Ebner
When Peter Elderon visited NRB to present the evolution of PL1, Benoit Ebner made this presentation on how this programmation language is used at NRB.
Nxll25 hsrp with failover
1. The document describes configuring high availability routing between two firewalls (ASA1 and ASA2) using failover, and between two routers (MLS3 and R2) using HSRP.
2. It provides configuration examples for failover on the ASAs, HSRP on MLS3 and R2, PAT on the ASA and R2, and EIGRP routing between the ASA and MLS3.
3. It also specifies default gateways for different PCs to reach R1 via the active HSRP router.
Nxll12 zone based firewall
The document describes tasks for configuring a zone-based firewall on Router 1:
1. Create an inside and outside zone on Router 1's interfaces; apply an inspect policy between the zones to allow necessary traffic.
2. Configure R2 to ping R3 by name by adding DNS and host entries.
3. Configure R2 to copy a file from R4's HTTP server using the file path and name.
4. Configure R2 as the NTP server and have the other routers synchronize to it after applying necessary firewall policies.
Nxll17 dynamic routing with asa
The document describes the steps to configure dynamic routing, site-to-site VPN, and network access between devices in a lab topology. The tasks include: 1) Configuring IP addresses and dynamic routing protocols on routers and firewalls, 2) Establishing connectivity between all devices, 3) Implementing NAT and VPN services on the firewalls to allow communication between specified subnets, and 4) Opening a non-standard port for remote access between two routers via one of the firewalls.
Nxll09 access list
This document provides instructions for completing 12 tasks to configure access control lists on routers. The tasks include configuring IP addresses, inter-VLAN routing, EIGRP routing, DNS, Telnet/SSH access, and ACLs to restrict traffic between VLANs and access to websites based on the VLAN. Detailed configuration steps are provided for each router to implement the access controls and routing as outlined in the tasks.
Nxll26 bgp ii
1. The document describes the configuration steps for a lab exercise involving BGP routing. It includes tasks to configure IP addresses, IBGP, HSRP, servers, and BGP routing on multiple routers as shown in the given topology diagram.
2. Key steps are to configure IBGP between routers R1-R4, HSRP between R5-R6, servers on R6, and BGP routing between all routers as specified in the tasks and topology, including IBGP, EBGP, route reflectors, and BGP confederations.
3. The goal is to verify connectivity between loopbacks and servers across the different BGP and IBGP domains as configured.
Nxll19 vrrp (virtual router redundancy protocol)
The document describes configuring VRRP (Virtual Router Redundancy Protocol) on routers R1 and R2. It involves:
1. Configuring R1 as the master for VRRP group 1 using virtual IP 10.0.0.254 and authentication.
2. Configuring R2 as the master for load-balanced VRRP group 2 using virtual IP 10.0.0.193 and a different authentication string.
3. Enabling tracking on both routers so that the priority of the backup router decreases if the route to the opposite network fails, allowing it to take over as master.
Nxll23 i pv6
The document provides instructions for configuring IPv6 on a network topology. It includes tasks to configure IPv6 addresses on routers, configure Frame-Relay over IPv6, assign IPv6 addresses to routers through autoconfiguration, and configure OSPF routing between the routers.
Nxll10 v lan and trunking
The document describes the tasks and solution for a lab on VLANs and trunking. The tasks are to: 1) Configure IP addresses as shown in the topology, 2) Create DHCP servers for VLANs 10 and 20, 3) Configure SW1 as the VTP server and the others as clients with the domain "netwaxlab.com", 4) Ensure PCs get IP addresses via DHCP, and 5) Allow communication between PCs 9 and 10 which have different IPs on the same VLAN. The solution describes the configurations needed on the switches to accomplish these tasks.
Configuration of Smtp Server On CentOS 8
This document provides instructions for configuring an SMTP server on CentOS 8, including installing Postfix and Dovecot, configuring configuration files like main.cf, master.cf, and firewall rules to allow access to ports 25, 465, and 587 for SMTP, SSL, and submission protocols. Key steps are installing Postfix and Dovecot packages, enabling and starting services, editing configuration files to set mail locations and UIDL formats, and opening required ports in the firewall.
Nxll18 vpn (s2 s gre & dmvpn)
1. The document describes configuring IP addresses, DNS, a site-to-site GRE VPN between routers R5 and R6, and a DMVPN network between routers R1, R2, and R3.
2. For the GRE VPN, ISAKMP and IPsec are configured on R5 and R6 using a preshared key of "netwaxlab" to secure the GRE tunnel.
3. For the DMVPN, R1 is configured as a hub router and R2 and R3 as spoke routers. ISAKMP and IPsec are configured using a preshared key of "netwaxlab" to secure the GRE tunnels between the routers.
Day 11 eigrp
http://www.cyberintelligents.in
info@cyberintelligents.in
https://www.facebook.com/cyberintelligents
https://in.linkedin.com/in/cyberintelligents/en
https://cyberintelligents.wordpress.com/
http://cyberintelligent.blogspot.in
+91 9876162698 +919988288019
http://trainingcyberintelligents.blogspot.com
https://cyberintelligentsnews.wordpress.com/
Nxll16 basic asa v8.2
The document provides instructions for configuring an ASA firewall to:
1. Configure security levels and interfaces for DMZ and DMZ1 subnets.
2. Enable ping access between the DMZ and DMZ1 interfaces.
3. Restrict telnet access to the ASA to only the R2 host.
4. Enable SSH access to the ASA from the ISP subnet only.
5. Apply PAT for the Inside, DMZ and DMZ1 interfaces.
6. Allow the ISP to telnet to the R2 host using port 2487.
Eincop Netwax Lab: EIGRP ii
1. The document describes configuring EIGRP routing on a network topology. This includes configuring EIGRP routing processes and interfaces, adjusting EIGRP timers, enabling authentication, setting metric weights, redistributing routes between EIGRP processes, summarizing routes, and filtering routes.
What's hot (19)
Eincop Netwax Lab: Site 2 Site VPN with Routing Protocols
Eincop Netwax Lab: Site 2 Site VPN with Routing Protocols
Eincop Netwax Lab: HSRP (Hot Standby Router Protocol)
Eincop Netwax Lab: HSRP (Hot Standby Router Protocol)
Usage, Performance and Future Of PL1 at NRB Benoit Ebner
Usage, Performance and Future Of PL1 at NRB Benoit Ebner
Similar to Hands on lab_instruction
Cisco labs practical4
This document provides instructions for configuring OSPF routing between routers. Key steps include:
1. Configure IP addresses and interfaces on the routers.
2. Configure OSPF routing process on each router to advertise networks in area 0. This includes adding loopback interfaces for stability.
3. Test connectivity between routers and hosts by pinging interfaces. Troubleshoot any issues until connectivity is established across the network.
Lab 9 instructions
This document describes configuring a basic single-area OSPFv2 network. It includes the topology diagram and addressing tables, and steps to build the network, configure OSPF routing on each router with area 0, and verify OSPF neighbor relationships and routing tables. It also provides sample outputs of show commands to check OSPF settings and interfaces.
Huawei ARG3 Router How To - Troubleshooting OSPF: Netmask mismatch
This third lesson about OSPF troubleshooting will be focused on “Netmask mismatch”. We will isolate the problem and we will correct the configuration.
OSPF Internal Route Summarization
The document discusses OSPF internal route summarization. It explains that OSPF summarization can only be configured on area border routers (ABRs) between areas, and that it involves using a route range to join multiple routes into fewer summary routes. Configuring summarization reduces routing table and link state database sizes. The example shows routing tables and link state databases before and after configuring a route range on an ABR to summarize two networks in an area into a single inter-area route.
1000 Ccna Questions And Answers
CCNA certification, CCNA training, CCNA course, CCNA Exam, CCNA certification, CCNA training, CCNA course, CCNA Exam, how to, how to,1000 CCNA Questions and Answers
การคอนฟิกส์ OSPF บน Ubiquiti Edge Router
The document provides instructions for configuring three Ubiquiti EdgeRouter devices (R1, R2, R3) with OSPF routing. It describes setting the IP addresses and OSPF parameters for each router, including their router IDs, networks, and areas. It confirms the OSPF configuration is working by showing R1 has learned the route to network 10.0.60.0/24 through R2 and can ping and trace route to R3 on that network. It also lists some common OSPF commands for viewing routes, neighbors, and interface information.
Exam viewer2
The document is a sample exam for CCNA certification that contains multiple choice questions about networking concepts. Some of the questions test knowledge of protocols like TCP, UDP, HTTP, SNMP, and protocols used for routing like OSPF, EIGRP, RIP. Other questions cover topics like VLANs, trunking, STP, and IP addressing schemes.
Lab6.4.1
This document provides instructions for configuring basic inter-VLAN routing on a network with three switches and one router. Key steps include:
1. Configuring VTP on the switches with one in server mode and two in client mode to propagate VLANs.
2. Creating VLANs 99, 10, 20 and 30 on the VTP server and assigning ports and IP addresses.
3. Configuring the router interface and subinterfaces for each VLAN to enable inter-VLAN routing.
4. Verifying connectivity between VLANs, which now routes through the router instead of failing.
ccna project on topic company infrastructure
Prince Gautam submitted a presentation on CCNA that introduces CCNA and networking. It defines CCNA, describes the importance of networking for communication and resource sharing. It also summarizes different types of networking including LAN, MAN, WAN and common networking devices like hubs, switches, routers. The presentation further explains concepts like subnetting, supernetting, routing protocols like RIP, EIGRP, OSPF and basic router configuration.
©LWTAOB© 2013 Cisco andLab – O.docx
©
L
W
T
A
O
B
© 2013 Cisco and
Lab – Ob
Wiresha
Topology
Addressing
R
S
S2
PC
PC
Objectives
Part 1: Bu
Part 2: Us
Part 3: Us
Part 4: Us
Backgroun
The Addre
address. W
d/or its affiliates.
bserving
ark
g Table
Device
1 G
1 V
2 V
C-A N
C-B N
uild and Con
se the Windo
se the IOS S
se Wireshark
nd / Scenar
ess Resolutio
When a frame
All rights reserve
g ARP w
Interface
G0/1
VLAN 1
VLAN 1
NIC
NIC
nfigure the N
ows ARP Co
how ARP Co
k to Examine
rio
on Protocol (A
e is placed on
ed. This docume
with the
IP Ad
192.168
192.168
192.168
192.168
192.168
etwork
mmand
ommand
e ARP Excha
ARP) is used
n the network
ent is Cisco Publ
Window
ddress
8.1.1 25
8.1.11 25
8.1.12 25
8.1.3 25
8.1.2 25
anges
by TCP/IP to
k, it must have
ic.
ws CLI, I
Subnet Mas
55.255.255.0
55.255.255.0
55.255.255.0
55.255.255.0
55.255.255.0
map a Layer
e a destinatio
OS CLI,
sk Defaul
N/A
192.16
192.16
192.16
192.16
r 3 IP address
n MAC addre
P
and
t Gateway
8.1.1
8.1.1
8.1.1
8.1.1
s to a Layer 2
ess. To dynam
Page 1 of 11
MAC
mically
Lab – Observing ARP with the Windows CLI, IOS CLI and Wireshark
© 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 2 of 11
discover the MAC address for the destination device, an ARP request is broadcast on the LAN. The device
that contains the destination IP address responds, and the MAC address is recorded in the ARP cache. Every
device on the LAN keeps its own ARP cache, or small area in RAM that holds ARP results. An ARP cache
timer removes ARP entries that have not been used for a certain period of time.
ARP is an excellent example of performance tradeoff. With no cache, ARP must continually request address
translations each time a frame is placed on the network. This adds latency to the communication and could
congest the LAN. Conversely, unlimited hold times could cause errors with devices that leave the network or
change the Layer 3 address.
A network administrator should be aware of ARP, but may not interact with the protocol on a regular basis.
ARP is a protocol that enables network devices to communicate with the TCP/IP protocol. Without ARP, there
is no efficient method to build the datagram Layer 2 destination address. Also, ARP is a potential security risk.
ARP spoofing, or ARP poisoning, is a technique used by an attacker to inject the wrong MAC address
association in a network. An attacker forges the MAC address of a device, and frames are sent to the wrong
destination. Manually configuring static ARP associations is one way to prevent ARP spoofing. Finally, an
authorized MAC address list may be configured on Cisco devices to restrict network access to only approved
devices.
In this lab, you will use the ARP commands in both Windows and Cisco routers to display the ARP table. You
will also clear the ARP cache and add static ARP entries.
Practice exam #2
The document contains multiple choice questions about network configuration and protocols. Based on the options provided, the correct answers are:
- The missing information for Blank 1 is the command show ip route.
- Addition of hosts to a physical segment and increasing use of bandwidth intensive network applications contribute to congestion on an Ethernet LAN.
- The SwA port has IEEE 802.1Q trunking enabled and the SwB port has ISL trunking enabled.
Introduction 140318015826-phpapp01
This document provides a summary of a presentation on CCNA (Cisco Certified Network Associate). It includes:
1. An introduction to CCNA, which stands for Cisco Certified Network Associate and provides information about networking, its types and applications. Networking is important for communication and resource sharing.
2. Descriptions of different types of networking including LAN, MAN, and WAN. It also lists common networking devices like LAN cards, bridges, hubs, switches, and routers.
3. Overviews of topics covered in CCNA including subnetting, supernetting, Classless Interdomain Routing (CIDR), the differences between hubs and switches, what routers are used for,
UIU Network System(Cn project)
The document describes a network design project to model the network of UIU University. Key elements include:
- The network uses RIP routing and DHCP for IP addressing. It connects labs, faculty PCs, servers and student laptops through wired and wireless connections.
- The network topology connects labs, faculty, and wireless access through separate routers linked to a central UIU router. Subnetting divides IP ranges for different sections.
- Devices are configured and IP addresses assigned using DHCP. Routing is established using RIP configuration on the routers. Testing shows connectivity between all devices on the network.
- While functional, the design could be improved by adding an ISP connection and implementing NAT and VLAN
OSPF_multi.pdf
This document provides instructions for configuring a multi-area OSPF network. SanJose1 is configured as an area border router (ABR) connecting Area 0 and Area 1. SanJose3 is also an ABR connecting Area 0 and Area 51. Singapore is configured to redistribute static routes learned from Auckland into Area 51, making it an autonomous system boundary router (ASBR). Inter-area route summarization is configured on SanJose1 to reduce routing table entries.
CCIE Lab - IGP Routing
The document discusses IP routing protocols RIP, RIP version 2, EIGRP, and OSPF. It provides details on configuration and features of each protocol, including route summarization, route filtering, default routing, and stub routing. It also covers troubleshooting routing loops caused by interface summaries in RIP and using leak maps in EIGRP.
Ccna 2 chapter 11 v4.0 answers 2011
This document provides 25 questions and answers related to CCNA 2 Chapter 11 on OSPF routing. OSPF is the Open Shortest Path First routing protocol. The questions cover topics like OSPF neighbor relationships, route calculations, DR/BDR elections, network statements, and troubleshooting.
119163798 icnd1-practice-questions-9tut
Here are the key steps to configure RIPv2 on Router1:
1. Enter configuration mode:
Router1> enable
Router1# configure terminal
2. Configure the FastEthernet 0/0 interface:
Router1(config)# interface FastEthernet 0/0
Router1(config-if)# ip address 192.168.12.1 255.255.255.0
Router1(config-if)# no shutdown
3. Configure the Serial 0/0 interface:
Router1(config-if)# interface Serial 0/0
Router1(config-if)# ip address 192.168.23.1 255.255.255.252
Router1(config-if
ccna summer training ppt ( Cisco certified network analysis) ppt. by Traun k...
This document provides a summary of a presentation on CCNA (Cisco Certified Network Associate). It was trained by Ravinder Kumar from Gurukul Technical Institute and submitted by Tarun Khaneja with roll number 2110045 and contact number 09034406598. The presentation introduces CCNA and discusses networking types and applications. It also covers networking devices, subnetting, routing protocols like RIP, EIGRP, OSPF, ACLs, VLANs, and inter-VLAN routing. Configuration examples are provided for EIGRP and RIP routing on the same network.
Lab8 Controlling traffic using Extended ACL Objectives Per.pdf
Lab8 Controlling traffic using Extended ACL
Objectives
Perform basic configuration tasks on a router.
Applying Static routes and default route.
Exploring the routing table entry.
Applying Extended (named) access control lists (ACLs).
Testing the access control lists (ACLs).
Required Resources
2 Cisco Routers (1841)
2 Cisco Switches (2950-24)
3 Computers
UTP (straight through and cross over) cables
Tasks:
A. Build up the topology.
B. Perform Basic Router Configurations
Steps:
1. Connect the components as shown in Fig 1.
2. Configure the router hostname to match the topology diagram.
3. Configure IP addresses and masks on all devices.
4. Configure a loopback interface (loopback 0) on R2 to simulate the ISP. (search on the internet
how to configure loopback interface)
C. Enable Static route for all networks.
Steps:
1. For Router 1
R1(config)# ip route 192.168.20.0 255.255.255.0 serial 0/0/0
Default root can be configured as:
R1(config)# ip route 0.0.0.0 0.0.0.0 10.1.1.2
2. For Router 2
R2(config)# ip route 192.168.10.0 255.255.255.0 serial 0/0/1
R2(config)# ip route 192.168.11.0 255.255.255.0 serial 0/0/1
D. Verify full IP connectivity using the ping command and the routing table of routers.
Step#1:
For R1 and R2, use the command show ip route, take a snapshot for the resulting routing table,
and discuss the outputs:
*Routing table of R1(Screenshoot)
*Routing table of R2 (Screenshot)
Step#2:
Make sure that the whole network nodes can ping each other.
Before configuring and applying this ACL, be sure to test connectivity from Laptop1 to the
loopback interface (ISP - 209.165.200.225)
E. Configuring an Extended ACL
In this section, you are configuring an extended ACL on R1 that blocks traffic originating from any
device on the 192.168.10.0/24 network to access the 209.165.200.255 host (the simulated ISP).
This ACL will be applied outbound on the R1 Serial 0/0/0 interface.
Steps:
1. Configure a named extended ACL.
R1(config)#ip access-list extended EXTEND-1
R1(config-ext-nacl)#deny ip 192.168.10.0 0.0.0.255 host 209.165.200.225
2. Apply the ACL.
With standard ACLs, the best practice is to place the ACL as close to the destination as possible.
Extended ACLs are typically placed close to the source.
R1(config)#interface serial 0/0/0
R1(config-if)#ip access-group EXTEND-1 out
3. Test the ACL.
From Laptop1; ping the loopback interface on R2.
R1(config-ext-nacl)#permit ip any any
**Please provide full code and screenshoots from Cisco packet tracer.
Table -1 begin{tabular}{|c|ccc|} hline Device & Interface & IP Address & Default Gateway & & & R1
& Fa0/0 & 192.168.10.1/24 & N/A & Fa0/1 & 192.168.11.1/24 & N/A & So/0/0 & 10.1.1.1/24 & N/A
& Fa0/1 & 192.168.20.1/24 & N/A R2 & So/0/1 & 10.1.1.2/24 & N/A & loopback 0 &
209.165.200.225/8 & N/A & & & & & 192.168.10.10/24 & 192.168 .10 .1 hline Laptop1 & NIC &
192.168.11.10/24 & 192.168 .11 .1 hline Laptop2 & NIC & 192.168.20.254/24 & 192.168 .20 .1
hline hline PC3 & NIC & & hline end{tabular}.
Comment by JCB Please center this on the pag.docx
Comment by JCB: Please center this on the page
Cisco Network Proposal Part 2Comment by JCB: This document should include to sites, Worchester and Boston, you have combined the requirements of both sites.
Worchester requires subnetting, the range of each subnet in a table, and encapsulation 802.1q configured.
Boston requires subnetting, all ranges displayed in a table, a routing protocol chosen and a summarized route advertised utilizing the routing protocol
CMIT 350 7982: Interconnecting Cisco Devices
Contents
Routing Protocol3
Summarization 3
Default Route 4
Topology8Site
The current site which I have been assigned to upgrade in Boston and do the routing, the default routing include Comment by JCB: You wording does not clearly state what you are trying to accomplish.
Recommend that you start by describing the Boston network then describe what you plan to do the fix it. For example
Title should be Boston Site Configuration (or something like this)
The Boston site consist of three (type) routers. The routers will be configured with the x.x.x.x/x. This subnet address will be subnetted to support the current configuration and allow for future expansion.
You actually have something below that should be moved up to the introduction paragraph about Boston. I have highlighted it in red.
You then want to talk about your intension to utilized the OSPF routing protocol and summarization to improve the network and the value it will bring.
Then you can start talking about each.
The subnetting would be a good topic at this point because you would have just finished talking about the network and how you intend to improve it. You can now state the subnet address that will be utilize to configure the router and that the subnet will be summarized
Next you can talk about the routing protocol and state that the summarized route will be used and why.
You can use one of these charts.
Why are you using subinterfaces? There is not requirement for VLANs at the Boston site.
3 – 2900 of integrated routers, the routers have four Ethernet cables and are connected to two serial cables. The diagram for the current cabling is as shown below.
Figure 1: Boston site topology
Comment by JCB: All figures, diagrams, and tables must be labeled and referenced in the test.
What is the purpose of the show ip interface brief command?
The site has implemented a routing protocol and the routers have been configured with the default routing protocol.
Proposed solutions and remedies
Routing Protocols
There are three main interior routing protocols:Comment by JCB: You don’t have to describe all the routing protocols, just pick one and state why you chose it. Then show an example of how to configured it.
i. OSPF protocol – This is a link-state classless protocol which is best suited across multi-vendor networks and extensive networks. The protocol can be used in a distance of 110 meters. The routing standard uses cost metric. Comment by JCB: Your formattin ...
Similar to Hands on lab_instruction (20)
Huawei ARG3 Router How To - Troubleshooting OSPF: Netmask mismatch
Huawei ARG3 Router How To - Troubleshooting OSPF: Netmask mismatch
ccna summer training ppt ( Cisco certified network analysis) ppt. by Traun k...
ccna summer training ppt ( Cisco certified network analysis) ppt. by Traun k...
Lab8 Controlling traffic using Extended ACL Objectives Per.pdf
Lab8 Controlling traffic using Extended ACL Objectives Per.pdf
More from trayyoo
ops300 Week5 storage
This document provides instructions and specifications for setting up a storage environment for virtual machines (VMs) and containers using Proxmox VE. It describes using block storage, file storage, and object storage (e.g. Ceph) and configuring storage pools and volumes. Small Ceph deployments are outlined using a single node configuration. Feedback is also provided on examples of networking between containers and VMs.
ops300 Week8 practical test
This document outlines the objectives and requirements for a practical networking test. It details that students must configure a topology (5%), implement a plan with interface screenshots (10%), provide test case evidence from tools like ping (30%), evidence of requirements from packet captures (40%), and show static routing rules (15%). It provides the allowed IP ranges and requires submitting screenshots, configs, and evidence before and after class. Penalties are assigned for poorly written reports, no internet access, late submissions, incorrect IPs, or using unsubmitted evidence. Bonuses are available for additional tasks like tunnels or distributed topologies.
ops300 Week8 gre
This document discusses setting up a GRE overlay network to create a distributed switch. It outlines creating GRE tunnels between endpoints, disabling NetworkManager, configuring interfaces and bridges, populating the routing table, allowing GRE traffic through the firewall, and testing connectivity. Troubleshooting steps include checking interfaces, IP addresses, routing tables, and firewall rules.
ops300 Week9 feedback
This document outlines several network connectivity scenarios involving virtual machines and containers with different grades. The highest grade (A/A+) involves an LXC container, 4 VMs, and both GRE and OpenVPN tunnels that must be established for the container and VMs to have internet access and ping each other. The next grades (B/B+ through D/D+) involve progressively fewer VMs and tunnels but similar connectivity requirements between the VMs and containers.
ops300 Week10 technology evaluation
This document outlines the process for evaluating technologies, which includes collecting material from various sources like search engines, papers, and documentation to summarize and organize; establishing evaluation criteria such as performance, security, and costs; and conducting experiments to test technologies, analyze results, and write a final report with conclusions.
ops300 Research paperrubric
This grading rubric evaluates research papers on four criteria: format/layout, content/information, quality of writing, and references and use of references. Each criterion has requirements for poor, good, and excellent performance. Format/layout addresses following length, font and style requirements. Content/information covers addressing all topics, technical soundness, research-based information, and coherence. Quality of writing focuses on clarity, grammar, and organization. References and use of references examines reference quality, effectiveness of use, correctness of citation and listing. The rubric also notes originality and authenticity as an overriding criterion.
ops300 Project(4)
This document outlines a course project to design and deploy an enterprise IT infrastructure for a small community college. Students will complete the project in phases, first proposing their design and then implementing virtualization and central logging. The goal is to reduce hardware needs through virtualization and automation. Requirements include setting up a learning management system, email server, content management system, VPN, Linux and Windows labs, kiosks, single sign-on, and on-demand services. The project will be graded based on meeting requirements, security, automation, and documentation in a final report.
ops300 Project(3)
This document outlines a course project to design and deploy an enterprise IT infrastructure for a small community college. Students will complete the project in phases, first proposing their design and then implementing virtualization, Active Directory, and centralized logging. The goal is for students to reduce hardware needs through virtualization and automation while meeting the college's requirements for services like email, websites, labs, and single sign-on access. Students will be graded based on how fully they meet requirements, secure systems, automate operations, and document their work.
ops300 Assignment 02
The document provides instructions for Assignment 02, which requires writing a formal research paper comparing public, private, and hybrid clouds. The paper must include sections on the advantages and disadvantages of each cloud type, case studies demonstrating appropriate uses of each type, and explanations of migration processes from traditional IT to various cloud environments. The paper must follow MLA style guidelines, cite all non-original material, and be submitted as a PDF. It will be graded based on an in-class discussion and the quality of the research paper.
ops300 Week5 storage (1)
This document provides instructions and specifications for setting up a storage environment for practical testing in Proxmox. It describes setting up various virtual machines and containers with Linux and Windows operating systems along with networking tools. It also covers configuring block storage, file storage, and object storage using local disks, RBD/Ceph distributed storage, and examples of container and virtual machine networking configurations for testing interconnection goals.
srt311 Project2
The document describes a project to build a secure web forum with Python. Users can create accounts to post content. Posts are checked for SQL injection and XSS vulnerabilities. Users' passwords are stored securely hashed with salt. The forum allows viewing all posts and signing in to post. When a new post is added, it appears at the bottom. The forum greets signed in users and allows posting, while providing sign in/account creation for others. Students will create scripts for account registration, login, posting, and securing against vulnerabilities. Code quality and documentation standards are also assessed.
Project papercontent requirement
This document outlines the structure and sections required for a research paper. It includes sections for an abstract, introduction, literature review, proposed approach, discussion, and references. The introduction provides background on the topic and the author's contribution. The literature review summarizes related work. The proposed approach presents the author's novel method in detail with comparisons to other approaches. The discussion provides critical analysis and addresses limitations.
Dcn330 project papertemplate(1)
The document provides a template for formatting academic papers with specific styles and guidelines. It includes sections for the title, authors and affiliations, abstract, keywords, body headings and text, figures and tables, references, copyright forms and acknowledgments. The template specifies the formatting for all text components, including fonts, spacing, headings, citations, references, and footnotes to facilitate electronic publication and consistency across publications. Authors are instructed to use the template to format their paper according to the specified styles and guidelines.
Dcn330 project-paper-rubric
This rubric outlines criteria for evaluating a DCN 330 project on a scale of 1-5. It assesses the originality, significance, quality, scientific soundness, and interest of the content. It also evaluates whether the project followed the provided writing template, included an analysis of existing approaches, used proper citation style, and contained clear introductions and conclusions that motivated the topic and summarized contributions. The total possible score is 60.
Introduction(2)
This document outlines the course DCN 330 which covers data communication and network interconnectivity, including distinguishing network devices, analyzing network designs, quality of service, cloud computing, and gaining hands-on experience through lectures, labs, and a course project using tools like Cisco Packet Tracer and lab equipment. Students will be evaluated through exams, quizzes, lab assignments, and a course project presentation and report.
Report for lab 1
This document is a lab report for determining connectivity issues between various computers and a web server. It details steps to check connectivity between PC-01 and the web server, PC-02 and the web server, PC-A and the web server, and PC-B and the web server. For each connection, the report instructs the user to ping various IP addresses and hosts, check web access, and document any issues found along with solutions.
Report for lab 2(2)
This document is a lab report for a networking course that asks the student to complete several tasks involving two routers and a switch. It instructs the student to fill in a table with device names, interfaces, IP addresses, subnet masks and default gateways. It also asks the student to explain how to connect their lab computer to the two routers, provide screenshots of ping tests between devices, explain how to remotely configure the actual routers from their computer, and provide screenshots of configuring each router.
Report for lab 3(1)
This document contains instructions for a lab assignment involving Cisco packet tracer. The student is asked to complete 4 questions:
1) Execute commands on Switch8 to view information like IOS version, model, and interfaces.
2) Explore the network topology in packet tracer and answer questions about the types of switches used and why routers are not needed.
3) Change the hostname of Switch4 and bring up and down an interface on the switch using CLI commands.
4) Attach screenshots showing the updated network topology and a ping test from PC0 to PC5.
Report for lab 4 2017(1)
This document summarizes the steps and questions from a lab report on configuring VLANs. It involves viewing default VLAN configurations, configuring VLANs on switches, assigning VLANs to ports, and testing connectivity between PCs in different VLANs. The final step is to make a configuration change to allow PCs in different VLANs to ping each other successfully and take a screenshot of the results.
Report for lab 5 2017
This document provides instructions for a lab assignment on subnetting and IP addressing. It outlines 8 steps to design an IP addressing scheme for a network with multiple subnets and router interfaces. The steps include determining subnet sizes, assigning subnet addresses, and allocating IP addresses to network device interfaces within each subnet.
More from trayyoo (20)
Recently uploaded
Azure Interview Questions and Answers PDF By ScholarHat
Azure Interview Questions and Answers PDF By ScholarHat
clinical examination of hip joint (1).pdf
described clinical examination all orthopeadic conditions .
BÀI TẬP BỔ TRỢ TIẾNG ANH 8 CẢ NĂM - GLOBAL SUCCESS - NĂM HỌC 2023-2024 (CÓ FI...
BÀI TẬP BỔ TRỢ TIẾNG ANH 8 CẢ NĂM - GLOBAL SUCCESS - NĂM HỌC 2023-2024 (CÓ FI...Nguyen Thanh Tu Collection
https://app.box.com/s/y977uz6bpd3af4qsebv7r9b7s21935vdAssessment and Planning in Educational technology.pptx
In an education system, it is understood that assessment is only for the students, but on the other hand, the Assessment of teachers is also an important aspect of the education system that ensures teachers are providing high-quality instruction to students. The assessment process can be used to provide feedback and support for professional development, to inform decisions about teacher retention or promotion, or to evaluate teacher effectiveness for accountability purposes.
Main Java[All of the Base Concepts}.docx
This is part 1 of my Java Learning Journey. This Contains Custom methods, classes, constructors, packages, multithreading , try- catch block, finally block and more.
Pollock and Snow "DEIA in the Scholarly Landscape, Session One: Setting Expec...
Pollock and Snow "DEIA in the Scholarly Landscape, Session One: Setting Expec...National Information Standards Organization (NISO)
This presentation was provided by Steph Pollock of The American Psychological Association’s Journals Program, and Damita Snow, of The American Society of Civil Engineers (ASCE), for the initial session of NISO's 2024 Training Series "DEIA in the Scholarly Landscape." Session One: 'Setting Expectations: a DEIA Primer,' was held June 6, 2024.Introduction to AI for Nonprofits with Tapp Network
Dive into the world of AI! Experts Jon Hill and Tareq Monaur will guide you through AI's role in enhancing nonprofit websites and basic marketing strategies, making it easy to understand and apply.
How to Add Chatter in the odoo 17 ERP Module
In Odoo, the chatter is like a chat tool that helps you work together on records. You can leave notes and track things, making it easier to talk with your team and partners. Inside chatter, all communication history, activity, and changes will be displayed.
Digital Artifact 1 - 10VCD Environments Unit
Digital Artifact 1 - 10VCD Environments Unit - NGV Pavilion Concept Design
ISO/IEC 27001, ISO/IEC 42001, and GDPR: Best Practices for Implementation and...
Denis is a dynamic and results-driven Chief Information Officer (CIO) with a distinguished career spanning information systems analysis and technical project management. With a proven track record of spearheading the design and delivery of cutting-edge Information Management solutions, he has consistently elevated business operations, streamlined reporting functions, and maximized process efficiency.
Certified as an ISO/IEC 27001: Information Security Management Systems (ISMS) Lead Implementer, Data Protection Officer, and Cyber Risks Analyst, Denis brings a heightened focus on data security, privacy, and cyber resilience to every endeavor.
His expertise extends across a diverse spectrum of reporting, database, and web development applications, underpinned by an exceptional grasp of data storage and virtualization technologies. His proficiency in application testing, database administration, and data cleansing ensures seamless execution of complex projects.
What sets Denis apart is his comprehensive understanding of Business and Systems Analysis technologies, honed through involvement in all phases of the Software Development Lifecycle (SDLC). From meticulous requirements gathering to precise analysis, innovative design, rigorous development, thorough testing, and successful implementation, he has consistently delivered exceptional results.
Throughout his career, he has taken on multifaceted roles, from leading technical project management teams to owning solutions that drive operational excellence. His conscientious and proactive approach is unwavering, whether he is working independently or collaboratively within a team. His ability to connect with colleagues on a personal level underscores his commitment to fostering a harmonious and productive workplace environment.
Date: May 29, 2024
Tags: Information Security, ISO/IEC 27001, ISO/IEC 42001, Artificial Intelligence, GDPR
-------------------------------------------------------------------------------
Find out more about ISO training and certification services
Training: ISO/IEC 27001 Information Security Management System - EN | PECB
ISO/IEC 42001 Artificial Intelligence Management System - EN | PECB
General Data Protection Regulation (GDPR) - Training Courses - EN | PECB
Webinars: https://pecb.com/webinars
Article: https://pecb.com/article
-------------------------------------------------------------------------------
For more information about PECB:
Website: https://pecb.com/
LinkedIn: https://www.linkedin.com/company/pecb/
Facebook: https://www.facebook.com/PECBInternational/
Slideshare: http://www.slideshare.net/PECBCERTIFICATION
South African Journal of Science: Writing with integrity workshop (2024)
South African Journal of Science: Writing with integrity workshop (2024)Academy of Science of South Africa
A workshop hosted by the South African Journal of Science aimed at postgraduate students and early career researchers with little or no experience in writing and publishing journal articles.বাংলাদেশ অর্থনৈতিক সমীক্ষা (Economic Review) ২০২৪ UJS App.pdf
বাংলাদেশের অর্থনৈতিক সমীক্ষা ২০২৪ [Bangladesh Economic Review 2024 Bangla.pdf] কম্পিউটার , ট্যাব ও স্মার্ট ফোন ভার্সন সহ সম্পূর্ণ বাংলা ই-বুক বা pdf বই " সুচিপত্র ...বুকমার্ক মেনু 🔖 ও হাইপার লিংক মেনু 📝👆 যুক্ত ..
আমাদের সবার জন্য খুব খুব গুরুত্বপূর্ণ একটি বই ..বিসিএস, ব্যাংক, ইউনিভার্সিটি ভর্তি ও যে কোন প্রতিযোগিতা মূলক পরীক্ষার জন্য এর খুব ইম্পরট্যান্ট একটি বিষয় ...তাছাড়া বাংলাদেশের সাম্প্রতিক যে কোন ডাটা বা তথ্য এই বইতে পাবেন ...
তাই একজন নাগরিক হিসাবে এই তথ্য গুলো আপনার জানা প্রয়োজন ...।
বিসিএস ও ব্যাংক এর লিখিত পরীক্ষা ...+এছাড়া মাধ্যমিক ও উচ্চমাধ্যমিকের স্টুডেন্টদের জন্য অনেক কাজে আসবে ...
A Survey of Techniques for Maximizing LLM Performance.pptx
A Survey of Techniques for Maximizing LLM Performance
ANATOMY AND BIOMECHANICS OF HIP JOINT.pdf
it describes the bony anatomy including the femoral head , acetabulum, labrum . also discusses the capsule , ligaments . muscle that act on the hip joint and the range of motion are outlined. factors affecting hip joint stability and weight transmission through the joint are summarized.
The Diamonds of 2023-2024 in the IGRA collection
A review of the growth of the Israel Genealogy Research Association Database Collection for the last 12 months. Our collection is now passed the 3 million mark and still growing. See which archives have contributed the most. See the different types of records we have, and which years have had records added. You can also see what we have for the future.
A Strategic Approach: GenAI in Education
Artificial Intelligence (AI) technologies such as Generative AI, Image Generators and Large Language Models have had a dramatic impact on teaching, learning and assessment over the past 18 months. The most immediate threat AI posed was to Academic Integrity with Higher Education Institutes (HEIs) focusing their efforts on combating the use of GenAI in assessment. Guidelines were developed for staff and students, policies put in place too. Innovative educators have forged paths in the use of Generative AI for teaching, learning and assessments leading to pockets of transformation springing up across HEIs, often with little or no top-down guidance, support or direction.
This Gasta posits a strategic approach to integrating AI into HEIs to prepare staff, students and the curriculum for an evolving world and workplace. We will highlight the advantages of working with these technologies beyond the realm of teaching, learning and assessment by considering prompt engineering skills, industry impact, curriculum changes, and the need for staff upskilling. In contrast, not engaging strategically with Generative AI poses risks, including falling behind peers, missed opportunities and failing to ensure our graduates remain employable. The rapid evolution of AI technologies necessitates a proactive and strategic approach if we are to remain relevant.
Recently uploaded (20)
Azure Interview Questions and Answers PDF By ScholarHat
Azure Interview Questions and Answers PDF By ScholarHat
Film vocab for eal 3 students: Australia the movie
Film vocab for eal 3 students: Australia the movie
BÀI TẬP BỔ TRỢ TIẾNG ANH 8 CẢ NĂM - GLOBAL SUCCESS - NĂM HỌC 2023-2024 (CÓ FI...
BÀI TẬP BỔ TRỢ TIẾNG ANH 8 CẢ NĂM - GLOBAL SUCCESS - NĂM HỌC 2023-2024 (CÓ FI...
Assessment and Planning in Educational technology.pptx
Assessment and Planning in Educational technology.pptx
Pollock and Snow "DEIA in the Scholarly Landscape, Session One: Setting Expec...
Pollock and Snow "DEIA in the Scholarly Landscape, Session One: Setting Expec...
Introduction to AI for Nonprofits with Tapp Network
Introduction to AI for Nonprofits with Tapp Network
ISO/IEC 27001, ISO/IEC 42001, and GDPR: Best Practices for Implementation and...
ISO/IEC 27001, ISO/IEC 42001, and GDPR: Best Practices for Implementation and...
South African Journal of Science: Writing with integrity workshop (2024)
South African Journal of Science: Writing with integrity workshop (2024)
বাংলাদেশ অর্থনৈতিক সমীক্ষা (Economic Review) ২০২৪ UJS App.pdf
বাংলাদেশ অর্থনৈতিক সমীক্ষা (Economic Review) ২০২৪ UJS App.pdf
A Survey of Techniques for Maximizing LLM Performance.pptx
A Survey of Techniques for Maximizing LLM Performance.pptx
Pride Month Slides 2024 David Douglas School District
Pride Month Slides 2024 David Douglas School District
Hands on lab_instruction
- 1. Packet Tracer Activity for Lab 8 In this section, you will use the following network and add OSPF routing. There are three lab activities and you should create the network by yourself. The first lab (Lab 8.1) requires you to configure three routers for OSPF and then view the configuration. Note that the labs were written to be used with real equipment and with any router simulator. You can replace the Ethernet links with WAN links if you want to. The labs are as follows: Lab 8.1: Enabling the OSPF Process Lab 8.2: Configuring OSPF Interfaces Lab 8.3: Verifying OSPF Operation Table 1 shows our IP addresses for each router (each interface uses a /24 mask). Table 1: Our IP addresses Router Interface IP address Lab_A Fa0/0 172.16.10.1 Lab_A S0/0/0 172.16.20.1 Lab_B S0/0/0 172.16.20.2 Lab_B S0/0/1 172.16.30.1 Lab_C S0/0/0 172.16.30.2
- 2. Lab_C Fa0/0 172.16.40.1 Hands-on Lab 8.1: Enabling the OSPF Process This is the first mandatory step in OSPF configuration. 1. Enable OSPF process 100 on Lab_A: Lab_A#conf t Enter configuration commands, one per line. End with CNTL/Z. Lab_A (config)#router ospf 100 Lab_A (config-router)#^Z 2. Enable OSPF process 101 on Lab_B: Lab_B#conf t Enter configuration commands, one per line. End with CNTL/Z. Lab_B (config)#router ospf 101 Lab_B (config-router)#^Z 3. Enable OSPF process 102 on Lab_C: Lab_C#conf t Enter configuration commands, one per line. End with CNTL/Z. Lab_C (config)#router ospf 102 Lab_C (config-router)#^Z Hands-on Lab 8.2: Configuring OSPF Interfaces The second mandatory step in OSPF is adding your network statements. 1. Configure the LAN and the network between Lab_A and Lab_B. Assign it to area 0. Lab_A#conf t Enter configuration commands, one per line. End with CNTL/Z. Lab_A (config)#router ospf 100 Lab_A (config-router)#network 172.16.10.1 0.0.0.0 area 0 Lab_A (config-router)#network 172.16.20.1 0.0.0.0 area 0
- 3. Lab_A (config-router)#^Z Lab_A # 2. Configure the networks on the Lab_B router. Assign them to area 0. Lab_B#conf t Enter configuration commands, one per line. End with CNTL/Z. Lab_B(config)#router ospf 101 Lab_B(config-router)#network 172.16.20.2 0.0.0.0 area 0 Lab_B(config-router)#network 172.16.30.1 0.0.0.0 area 0 Lab_B(config-router)#^Z Lab_B # 3. Configure the networks on the Lab_C router. Assign them to area 0. Lab_C#conf t Enter configuration commands, one per line. End with CNTL/Z. Lab_C(config)#router ospf 102 Lab_C(config-router)#network 172.16.30.2 0.0.0.0 area 0 Lab_C(config-router)#network 172.16.40.1 0.0.0.0 area 0 Lab_C(config-router)#^Z Lab_C# Hands-on Lab 8.3: Verifying OSPF Operation You need to be able to verify what you configure. 1. Execute a show ip ospf neighbors command from the Lab_A router and view the results. Lab_A#sho ip ospf neig 2. Execute a show ip route command to verify that all other routers are learning all routes. Lab_A#sho ip route 3. Execute a show ip protocols command to verify OSPF information. Lab_A#sho ip protocols 4. Execute a show ip OSPF command to verify your RID. Lab_A#sho ip ospf 5. Execute a show ip ospf interface f0/0 command to verify your timers. Lab_A#sho ip ospf int f0/0
- 4. Great! You just finished the hands-on lab tasks. Remember to upload your finished PKT file separately with your lab report to the Blackboard!