This document provides a review of techniques for designing broadband microstrip patch antennas. It discusses how microstrip patch antennas inherently have narrow bandwidths, and various techniques that have been used to enhance the bandwidth in recent decades. These techniques include using shorting pins, slot loading on patches, planar meta-material unit cells, and conductive biasing. The review then examines specific examples from literature on compact circularly polarized patch designs using slots, and UWB designs using parasitic elements and slots. Overall, the document aims to critically review different approaches for fabricating microstrip patch antennas with broader bandwidths.
DESIGN OF A COMPACT CIRCULAR MICROSTRIP PATCH ANTENNA FOR WLAN APPLICATIONS pijans
This paper presents the design of a compact circular microstrip patch antenna for WLAN applications which covers the band 5.15 to 5.825 GHz. The antenna is designed using 1.4mm thick FR-4 (lossy)substrate with relative permittivity 4.4 and a microstrip line feed is used. The radius of the circular patch is chosen as 7.62mm. To reduce the size and enhance the performance of the proposed antenna, a circular slot is loaded on circular patch and a square slot is etched on the ground plane of dimension 30mm×30mm. Design of the antenna is carried out using CST Microsoft Studio Sonimulation Software. The proposed antenna resonates at 5.5 GHz with a wider bandwidth of 702 MHz and it provides low return loss of -31.58 dB, good gain of 3.23 dB and directivity of 4.28 dBi and high efficiency of around 79% against the resonance frequency. The geometry of the proposed circular antenna with reduced size and its various performance parameters such as return loss, bandwidth, VSWR, gain, directivity, efficiency and radiation pattern plots are presented and discussed.
Phi shape uwb antenna with band notch characteristicsKiran Ajetrao
In this paper a novel band notch antenna in UWB
frequency range is designed using split rings. Split rings are
overlapped with designed monopole to give phi shape. The slit
gap gives band-notch operation from 5.1GHz to 6.29GHz and
from 4.94GHz to 5.91GHz for SPSSR and SPSCR antennas
respectively. Simulated and measured results are in good
agreement.
In this paper a compact, flexible, Multiband antenna is designed. It is having flexible Substrate of photographic paper which makes the antenna conformal. The antenna with two U slots cut in radiating patch is offset fed by microstrip lines gives the multiple bands of WLAN/WIMAX Application and two parasitic Elements improves the bandwidth of a typical microstrip antenna. The Measured results shows that the antenna resonates between Frequency band 2.10-2.95 GHz, 3.35-3.54 GHz and 5.04-6.0Hz.which are used for application such as Bluetooth, Wi-Fi, Zigbee, ISM 2.4GHz,WLAN WiMAX, and WLAN 5.2GHz.
Designing large-scale antenna array using sub-arrayjournalBEEI
Antenna array of large scale have been examined for different applications including 5G technology. To get better data rate or a reliable link substantial number of antenna arrays have been utilized to provide high multiplexing gains as well as array gains with high directivity. In this paper a simple but efficient implementation technique of using sub-arrays for the improvement of large-sized uniform arrays. By repeating a small sub-array multiple times large arrays can be designed. This implication of utilizing small array simplifies the design of a larger array which allows the designer to concentrate on the smaller sub-array before assembling larger arrays. So, by investigating the sub arrays the performance and radiation characteristics of large arrays can be anticipated. The array-factor for a planar sub-array of 2x2 (4 elements) is analyzed using Mat-lab software and then a large array is formed by placing the 2x2 sub-array indifferent configurations in a rectangular arrangements up to 8x8 planar array. And then the results are validated with CST (Computer simulation technology) simulation results.In this way the array-factors, directivities, HPBWs, and side lobes of the constructed large arrays are analyzed and associated with the small sub-array.
Design of Dual Frequency Antenna For Global Positioning systemijsrd.com
In recent years low profile, light weight antennas are preferred for the applications which need mobility. In this research the polygonal-shape Microstrip Single Patch Antenna has been designed for GPS dual resonant frequencies (GPS L1 1.575 GHz & L5 1.176 GHz band). Simulated results for main parameters such as return loss, bandwidth, radiation patterns and gains are also discussed herein. The Designing, Simulation & Optimization of this antenna is done in ADS Software. Result of the simulation shows at 1.575 GHz and 1.176 GHz, the antenna has return loss at -20.862 dB and -14.162 dB respectively. .
DESIGN OF A COMPACT CIRCULAR MICROSTRIP PATCH ANTENNA FOR WLAN APPLICATIONS pijans
This paper presents the design of a compact circular microstrip patch antenna for WLAN applications which covers the band 5.15 to 5.825 GHz. The antenna is designed using 1.4mm thick FR-4 (lossy)substrate with relative permittivity 4.4 and a microstrip line feed is used. The radius of the circular patch is chosen as 7.62mm. To reduce the size and enhance the performance of the proposed antenna, a circular slot is loaded on circular patch and a square slot is etched on the ground plane of dimension 30mm×30mm. Design of the antenna is carried out using CST Microsoft Studio Sonimulation Software. The proposed antenna resonates at 5.5 GHz with a wider bandwidth of 702 MHz and it provides low return loss of -31.58 dB, good gain of 3.23 dB and directivity of 4.28 dBi and high efficiency of around 79% against the resonance frequency. The geometry of the proposed circular antenna with reduced size and its various performance parameters such as return loss, bandwidth, VSWR, gain, directivity, efficiency and radiation pattern plots are presented and discussed.
Phi shape uwb antenna with band notch characteristicsKiran Ajetrao
In this paper a novel band notch antenna in UWB
frequency range is designed using split rings. Split rings are
overlapped with designed monopole to give phi shape. The slit
gap gives band-notch operation from 5.1GHz to 6.29GHz and
from 4.94GHz to 5.91GHz for SPSSR and SPSCR antennas
respectively. Simulated and measured results are in good
agreement.
In this paper a compact, flexible, Multiband antenna is designed. It is having flexible Substrate of photographic paper which makes the antenna conformal. The antenna with two U slots cut in radiating patch is offset fed by microstrip lines gives the multiple bands of WLAN/WIMAX Application and two parasitic Elements improves the bandwidth of a typical microstrip antenna. The Measured results shows that the antenna resonates between Frequency band 2.10-2.95 GHz, 3.35-3.54 GHz and 5.04-6.0Hz.which are used for application such as Bluetooth, Wi-Fi, Zigbee, ISM 2.4GHz,WLAN WiMAX, and WLAN 5.2GHz.
Designing large-scale antenna array using sub-arrayjournalBEEI
Antenna array of large scale have been examined for different applications including 5G technology. To get better data rate or a reliable link substantial number of antenna arrays have been utilized to provide high multiplexing gains as well as array gains with high directivity. In this paper a simple but efficient implementation technique of using sub-arrays for the improvement of large-sized uniform arrays. By repeating a small sub-array multiple times large arrays can be designed. This implication of utilizing small array simplifies the design of a larger array which allows the designer to concentrate on the smaller sub-array before assembling larger arrays. So, by investigating the sub arrays the performance and radiation characteristics of large arrays can be anticipated. The array-factor for a planar sub-array of 2x2 (4 elements) is analyzed using Mat-lab software and then a large array is formed by placing the 2x2 sub-array indifferent configurations in a rectangular arrangements up to 8x8 planar array. And then the results are validated with CST (Computer simulation technology) simulation results.In this way the array-factors, directivities, HPBWs, and side lobes of the constructed large arrays are analyzed and associated with the small sub-array.
Design of Dual Frequency Antenna For Global Positioning systemijsrd.com
In recent years low profile, light weight antennas are preferred for the applications which need mobility. In this research the polygonal-shape Microstrip Single Patch Antenna has been designed for GPS dual resonant frequencies (GPS L1 1.575 GHz & L5 1.176 GHz band). Simulated results for main parameters such as return loss, bandwidth, radiation patterns and gains are also discussed herein. The Designing, Simulation & Optimization of this antenna is done in ADS Software. Result of the simulation shows at 1.575 GHz and 1.176 GHz, the antenna has return loss at -20.862 dB and -14.162 dB respectively. .
Comparative analyses of enhancing bandwidth of micro strip patch antennas a s...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
Design and Analysis of Microstrip Antenna for CDMA Systems CommunicationIOSR Journals
This paper proposes a newly designed microstrip patch antennas (MSA) for wireless application
(CDMA Systems). The designed single antenna E-shaped patch antenna. Two parallel slots are in corporated
into the patch of a microstrip antenna to expand it bandwidth, and designed antenna operates in the frequency
range of 1.85 to 1.99 GHz. The antenna is designed using air as a dielectric substrate between the ground plane
and substrate patch antenna. IE3D is a full-wave electromagnetic simulator based on the method of moments
(MoM) technique. It has been widely used in the design of MICs, RFICs, patch antennas, wire antennas, and
other RF/wireless antennas. It can be used to calculate and plot the S parameters, VSWR, current distributions
as well as the radiation patterns. The results obtained for each patch were 2D and 3D view of patch, Directivity,
Gain, beam width and other such parameters, true and mapped 3D radiation pattern, and 2D polar radiation
pattern. The antenna successfully achieves the exhibit a broad impedance bandwidth of 27 % (at VSWR < 2)
with respect to the center frequency of 1.9 GHz is designed, fabricated, and finally measured on Spectrum
analyzer. The radiation pattern and directivity are also presented.. Gain maximum achievable is 3 dBi and good
return loss (S11 parameters) of -30 dB is achieved along with broadside radiation pattern.
A Compact Wideband Monopole Antenna using Single Open Loop Resonator for Wire...TELKOMNIKA JOURNAL
A novel single layer, microstrip line fed compact wideband monopole antenna using open loop resonator has been designed and analyzed. The proposed antenna occupies a compact size of only 30 36.5 1.6 mm3. A partial ground plane is employed to enhance the operating bandwidth and reflection coefficient of the proposed antenna. The variations in operating bandwidth of the proposed antenna can be easily controlled by properly adjusting the position of the gap in the open loop resonator.The antenna prototype is fabricated on FR4 substrate with a dielectric constant 4.2. In this design, the antenna exhibits 10dB wide impedance bandwidth of 61% from 2.0174 to 3.7903 GHz.The antenna can be easily fed using a 50 Ω microstrip feed line and it covers the bandwidth requirements of a number of modern wireless communication systems such as IEEE 502.11b WLAN band (2.4 2.5 GHz), extended UMTS (2.5 2.69 GHz), IMT (2.7 2.9 GHz), and IEEE 802.16 Wi MAX band (3.3 3.6 GHz) applications. The desired antenna is designed and simulated using Computer Simulation Technology (CST). An extensive analysis of the antenna parameters (reflection coefficient, radiation pattern, directivity, and VSWR) including surface current distributions is presented and discussed in this paper. Good agreement between simulated and measured result is obtained.
A miniaturized printed UWB antenna with dual notching for X-b and and aeronau...TELKOMNIKA JOURNAL
A low cost miniaturized UWB microstrip antenna with dual notched band for X band and aeronautical radio navigation (ARN) is presented in this article. The antenna (19 16×"> 25 mm2) is composed of a half-circular ring as a radiation patch with an incomplete ground plane. The measured results indicate a fractional bandwidth of 112% for 16S11≤-"> 10 dB between 3 to 10.6 GHz. The dual notched band has been achieved by incorporating window shaped microstrip closed ring resonators at the rear surface of the designed structure. The first notch band is centered at 7.5 GHz (7 8.1 GHz) to reject interference with X-band downlink (7.25 to 7.74 GHz) and second band centered at 9.1 GHz (8.6 9.4 GHz) to reject interference with aeronautical radio navigation (ARN) (8.7 to 9.2 GHz). The simulated and measured return loss, radiation pattern, and gain shows good agreement which confirms the applicability of the designed antenna for the intended UWB applications.
Electrically small antennas: The art of miniaturizationEditor IJARCET
We are living in the technological era, were we preferred to have the portable devices rather than unmovable devices. We are isolating our self rom the wires and we are becoming the habitual of wireless world what makes the device portable? I guess physical dimensions (mechanical) of that particular device, but along with this the electrical dimension is of the device is also of great importance. Reducing the physical dimension of the antenna would result in the small antenna but not electrically small antenna. We have different definition for the electrically small antenna but the one which is most appropriate is, where k is the wave number and is equal to and a is the radius of the imaginary sphere circumscribing the maximum dimension of the antenna. As the present day electronic devices progress to diminish in size, technocrats have become increasingly concentrated on electrically small antenna (ESA) designs to reduce the size of the antenna in the overall electronics system. Researchers in many fields, including RF and Microwave, biomedical technology and national intelligence, can benefit from electrically small antennas as long as the performance of the designed ESA meets the system requirement.
Optical Wireless Communication (OWC) has attracted the researchers as an alternative broadband technology for wireless communication. In OWC optical beams are used to transport data through atmosphere or even vacuum. We have proposed an OWC model and analyze the transmission performance of OW channel for indoor/ outdoor application. The performance has been judged on the basis of key parameters like BER and OSNR. A theoretical model has also been presented and validated by the simulation results. The proposed OWC channel was simulated in Optisystem which is a powerful tool of Optical communication System
A compact triband microstrip antenna utilizing hexagonal CSRR for wireless co...journalBEEI
In this paper, a compact triband printed antenna with hexagonal complementary split-ring resonators (CSRRs) for 4G applications is proposed. The proposed multiband antenna is comprised of a rectangular patch antenna on the top plane, while on the ground plane, hexagonal CSRRs are etched for size miniaturization (at the lower bands) and multiband generation. Another effect of the CSRR is the shifting of the initial resonance of the patch antenna from 5.17 GHz to the higher band of 6.18 GHz. The triband of 180 MHz 2.4~2.59, 150 MHz 2.79~2.94 and 420 MHz 6.04~6.46 GHz bands acquired can cover WLAN/Wi-Fi and WiMAX operating bands adequately. This can be achieved by choosing the optimal size and position of the CSRR on the ground plane carefully. The design occupies a total size of 45 x 45 mm2 using the low-cost FR-4 substrate. Good agreements are obtained between the measured results and the simulated, which are discussed and presented.
International Journal of Engineering Research and Applications (IJERA) is a team of researchers not publication services or private publications running the journals for monetary benefits, we are association of scientists and academia who focus only on supporting authors who want to publish their work. The articles published in our journal can be accessed online, all the articles will be archived for real time access.
Our journal system primarily aims to bring out the research talent and the works done by sciaentists, academia, engineers, practitioners, scholars, post graduate students of engineering and science. This journal aims to cover the scientific research in a broader sense and not publishing a niche area of research facilitating researchers from various verticals to publish their papers. It is also aimed to provide a platform for the researchers to publish in a shorter of time, enabling them to continue further All articles published are freely available to scientific researchers in the Government agencies,educators and the general public. We are taking serious efforts to promote our journal across the globe in various ways, we are sure that our journal will act as a scientific platform for all researchers to publish their works online.
International Journal of Computational Engineering Research (IJCER) is dedicated to protecting personal information and will make every reasonable effort to handle collected information appropriately. All information collected, as well as related requests, will be handled as carefully and efficiently as possible in accordance with IJCER standards for integrity and objectivity.
E shape microstrip patch antenna design for wimax applications, international...Sk Sohag
This paper presents the design & simulation of E-shape microstrip patch antenna exhibiting wideband operating frequencies for various wireless applications. This antenna will provide the wide bandwidth which is required in various applications like remote sensing, biomedical application, mobile radio satellite, wireless communication etc. The coaxial feed or probe feed technique is used in the experiment. The performance of the designed antenna was analyzed in terms of bandwidth, gain, return loss, VSWR, and radiation pattern. The design is optimized to meet the best possible result. The proposed antenna is designed by air substrate which has a dielectric constant of 1.0006. The results show the wideband antenna is able to operate from 8.80 to 13.49 GHz frequency band with optimum frequency at 8.73 GHz.
Performance Analysis of Corporate Feed Rectangular Patch Element and Circular...Mohamed Hassouna
This paper present simple, slim, low cost and high gain circular patch and rectangular patch microstrip array antenna, with the details steps of design process, operate in X-band(8 GHz to 12 GHz) and it provides a mean to choose the effective one based on the performance analysis of both of these array antennas. The method of analysis, design and development of these array antennas are explained completely here and analyses are carried out for 4x2 arrays. The simulation has been performed by using commercially available antenna simulator, SONNET version V12.56, to compute the current distribution, return loss response and radiation pattern. The proposed antennas are designed by using Taconic TLY-5 dielectric substrate with permittivity, εr = 2.2 and height, h =1.588 mm. In all cases we get return losses in the range -4.96 dB to -25.21 dB at frequencies around 10 GHz. The gain of these antennas as simulated are found above 6 dB and side lobe label is maintained lower than main lobe. Operating frequency of these antennas is 10 GHz so these antennas are suitable for X-band application.
DESIGN OF A COMPACT CIRCULAR MICROSTRIP PATCH ANTENNA FOR WLAN APPLICATIONSpijans
This paper presents the design of a compact circular microstrip patch antenna for WLAN applications
which covers the band 5.15 to 5.825 GHz. The antenna is designed using 1.4mm thick FR-4
(lossy)substrate with relative permittivity 4.4 and a microstrip line feed is used. The radius of the
circular patch is chosen as 7.62mm. To reduce the size and enhance the performance of the proposed
antenna, a circular slot is loaded on circular patch and a square slot is etched on the ground plane of
dimension 30mm×30mm. Design of the antenna is carried out using CST Microsoft Studio Sonimulation
Software. The proposed antenna resonates at 5.5 GHz with a wider bandwidth of 702 MHz and it provides
low return loss of -31.58 dB, good gain of 3.23 dB and directivity of 4.28 dBi and high efficiency of around
79% against the resonance frequency. The geometry of the proposed circular antenna with reduced size
and its various performance parameters such as return loss, bandwidth, VSWR, gain, directivity, efficiency
and radiation pattern plots are presented and discussed.
DESIGN OF A COMPACT CIRCULAR MICROSTRIP PATCH ANTENNA FOR WLAN APPLICATIONSpijans
This paper presents the design of a compact circular microstrip patch antenna for WLAN applications
which covers the band 5.15 to 5.825 GHz. The antenna is designed using 1.4mm thick FR-4
(lossy)substrate with relative permittivity 4.4 and a microstrip line feed is used. The radius of the
circular patch is chosen as 7.62mm. To reduce the size and enhance the performance of the proposed
antenna, a circular slot is loaded on circular patch and a square slot is etched on the ground plane of
dimension 30mm×30mm. Design of the antenna is carried out using CST Microsoft Studio Sonimulation
Software. The proposed antenna resonates at 5.5 GHz with a wider bandwidth of 702 MHz and it provides
low return loss of -31.58 dB, good gain of 3.23 dB and directivity of 4.28 dBi and high efficiency of around
79% against the resonance frequency. The geometry of the proposed circular antenna with reduced size
and its various performance parameters such as return loss, bandwidth, VSWR, gain, directivity, efficiency
and radiation pattern plots are presented and discussed
Comparative analyses of enhancing bandwidth of micro strip patch antennas a s...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
Design and Analysis of Microstrip Antenna for CDMA Systems CommunicationIOSR Journals
This paper proposes a newly designed microstrip patch antennas (MSA) for wireless application
(CDMA Systems). The designed single antenna E-shaped patch antenna. Two parallel slots are in corporated
into the patch of a microstrip antenna to expand it bandwidth, and designed antenna operates in the frequency
range of 1.85 to 1.99 GHz. The antenna is designed using air as a dielectric substrate between the ground plane
and substrate patch antenna. IE3D is a full-wave electromagnetic simulator based on the method of moments
(MoM) technique. It has been widely used in the design of MICs, RFICs, patch antennas, wire antennas, and
other RF/wireless antennas. It can be used to calculate and plot the S parameters, VSWR, current distributions
as well as the radiation patterns. The results obtained for each patch were 2D and 3D view of patch, Directivity,
Gain, beam width and other such parameters, true and mapped 3D radiation pattern, and 2D polar radiation
pattern. The antenna successfully achieves the exhibit a broad impedance bandwidth of 27 % (at VSWR < 2)
with respect to the center frequency of 1.9 GHz is designed, fabricated, and finally measured on Spectrum
analyzer. The radiation pattern and directivity are also presented.. Gain maximum achievable is 3 dBi and good
return loss (S11 parameters) of -30 dB is achieved along with broadside radiation pattern.
A Compact Wideband Monopole Antenna using Single Open Loop Resonator for Wire...TELKOMNIKA JOURNAL
A novel single layer, microstrip line fed compact wideband monopole antenna using open loop resonator has been designed and analyzed. The proposed antenna occupies a compact size of only 30 36.5 1.6 mm3. A partial ground plane is employed to enhance the operating bandwidth and reflection coefficient of the proposed antenna. The variations in operating bandwidth of the proposed antenna can be easily controlled by properly adjusting the position of the gap in the open loop resonator.The antenna prototype is fabricated on FR4 substrate with a dielectric constant 4.2. In this design, the antenna exhibits 10dB wide impedance bandwidth of 61% from 2.0174 to 3.7903 GHz.The antenna can be easily fed using a 50 Ω microstrip feed line and it covers the bandwidth requirements of a number of modern wireless communication systems such as IEEE 502.11b WLAN band (2.4 2.5 GHz), extended UMTS (2.5 2.69 GHz), IMT (2.7 2.9 GHz), and IEEE 802.16 Wi MAX band (3.3 3.6 GHz) applications. The desired antenna is designed and simulated using Computer Simulation Technology (CST). An extensive analysis of the antenna parameters (reflection coefficient, radiation pattern, directivity, and VSWR) including surface current distributions is presented and discussed in this paper. Good agreement between simulated and measured result is obtained.
A miniaturized printed UWB antenna with dual notching for X-b and and aeronau...TELKOMNIKA JOURNAL
A low cost miniaturized UWB microstrip antenna with dual notched band for X band and aeronautical radio navigation (ARN) is presented in this article. The antenna (19 16×"> 25 mm2) is composed of a half-circular ring as a radiation patch with an incomplete ground plane. The measured results indicate a fractional bandwidth of 112% for 16S11≤-"> 10 dB between 3 to 10.6 GHz. The dual notched band has been achieved by incorporating window shaped microstrip closed ring resonators at the rear surface of the designed structure. The first notch band is centered at 7.5 GHz (7 8.1 GHz) to reject interference with X-band downlink (7.25 to 7.74 GHz) and second band centered at 9.1 GHz (8.6 9.4 GHz) to reject interference with aeronautical radio navigation (ARN) (8.7 to 9.2 GHz). The simulated and measured return loss, radiation pattern, and gain shows good agreement which confirms the applicability of the designed antenna for the intended UWB applications.
Electrically small antennas: The art of miniaturizationEditor IJARCET
We are living in the technological era, were we preferred to have the portable devices rather than unmovable devices. We are isolating our self rom the wires and we are becoming the habitual of wireless world what makes the device portable? I guess physical dimensions (mechanical) of that particular device, but along with this the electrical dimension is of the device is also of great importance. Reducing the physical dimension of the antenna would result in the small antenna but not electrically small antenna. We have different definition for the electrically small antenna but the one which is most appropriate is, where k is the wave number and is equal to and a is the radius of the imaginary sphere circumscribing the maximum dimension of the antenna. As the present day electronic devices progress to diminish in size, technocrats have become increasingly concentrated on electrically small antenna (ESA) designs to reduce the size of the antenna in the overall electronics system. Researchers in many fields, including RF and Microwave, biomedical technology and national intelligence, can benefit from electrically small antennas as long as the performance of the designed ESA meets the system requirement.
Optical Wireless Communication (OWC) has attracted the researchers as an alternative broadband technology for wireless communication. In OWC optical beams are used to transport data through atmosphere or even vacuum. We have proposed an OWC model and analyze the transmission performance of OW channel for indoor/ outdoor application. The performance has been judged on the basis of key parameters like BER and OSNR. A theoretical model has also been presented and validated by the simulation results. The proposed OWC channel was simulated in Optisystem which is a powerful tool of Optical communication System
A compact triband microstrip antenna utilizing hexagonal CSRR for wireless co...journalBEEI
In this paper, a compact triband printed antenna with hexagonal complementary split-ring resonators (CSRRs) for 4G applications is proposed. The proposed multiband antenna is comprised of a rectangular patch antenna on the top plane, while on the ground plane, hexagonal CSRRs are etched for size miniaturization (at the lower bands) and multiband generation. Another effect of the CSRR is the shifting of the initial resonance of the patch antenna from 5.17 GHz to the higher band of 6.18 GHz. The triband of 180 MHz 2.4~2.59, 150 MHz 2.79~2.94 and 420 MHz 6.04~6.46 GHz bands acquired can cover WLAN/Wi-Fi and WiMAX operating bands adequately. This can be achieved by choosing the optimal size and position of the CSRR on the ground plane carefully. The design occupies a total size of 45 x 45 mm2 using the low-cost FR-4 substrate. Good agreements are obtained between the measured results and the simulated, which are discussed and presented.
International Journal of Engineering Research and Applications (IJERA) is a team of researchers not publication services or private publications running the journals for monetary benefits, we are association of scientists and academia who focus only on supporting authors who want to publish their work. The articles published in our journal can be accessed online, all the articles will be archived for real time access.
Our journal system primarily aims to bring out the research talent and the works done by sciaentists, academia, engineers, practitioners, scholars, post graduate students of engineering and science. This journal aims to cover the scientific research in a broader sense and not publishing a niche area of research facilitating researchers from various verticals to publish their papers. It is also aimed to provide a platform for the researchers to publish in a shorter of time, enabling them to continue further All articles published are freely available to scientific researchers in the Government agencies,educators and the general public. We are taking serious efforts to promote our journal across the globe in various ways, we are sure that our journal will act as a scientific platform for all researchers to publish their works online.
International Journal of Computational Engineering Research (IJCER) is dedicated to protecting personal information and will make every reasonable effort to handle collected information appropriately. All information collected, as well as related requests, will be handled as carefully and efficiently as possible in accordance with IJCER standards for integrity and objectivity.
E shape microstrip patch antenna design for wimax applications, international...Sk Sohag
This paper presents the design & simulation of E-shape microstrip patch antenna exhibiting wideband operating frequencies for various wireless applications. This antenna will provide the wide bandwidth which is required in various applications like remote sensing, biomedical application, mobile radio satellite, wireless communication etc. The coaxial feed or probe feed technique is used in the experiment. The performance of the designed antenna was analyzed in terms of bandwidth, gain, return loss, VSWR, and radiation pattern. The design is optimized to meet the best possible result. The proposed antenna is designed by air substrate which has a dielectric constant of 1.0006. The results show the wideband antenna is able to operate from 8.80 to 13.49 GHz frequency band with optimum frequency at 8.73 GHz.
Performance Analysis of Corporate Feed Rectangular Patch Element and Circular...Mohamed Hassouna
This paper present simple, slim, low cost and high gain circular patch and rectangular patch microstrip array antenna, with the details steps of design process, operate in X-band(8 GHz to 12 GHz) and it provides a mean to choose the effective one based on the performance analysis of both of these array antennas. The method of analysis, design and development of these array antennas are explained completely here and analyses are carried out for 4x2 arrays. The simulation has been performed by using commercially available antenna simulator, SONNET version V12.56, to compute the current distribution, return loss response and radiation pattern. The proposed antennas are designed by using Taconic TLY-5 dielectric substrate with permittivity, εr = 2.2 and height, h =1.588 mm. In all cases we get return losses in the range -4.96 dB to -25.21 dB at frequencies around 10 GHz. The gain of these antennas as simulated are found above 6 dB and side lobe label is maintained lower than main lobe. Operating frequency of these antennas is 10 GHz so these antennas are suitable for X-band application.
DESIGN OF A COMPACT CIRCULAR MICROSTRIP PATCH ANTENNA FOR WLAN APPLICATIONSpijans
This paper presents the design of a compact circular microstrip patch antenna for WLAN applications
which covers the band 5.15 to 5.825 GHz. The antenna is designed using 1.4mm thick FR-4
(lossy)substrate with relative permittivity 4.4 and a microstrip line feed is used. The radius of the
circular patch is chosen as 7.62mm. To reduce the size and enhance the performance of the proposed
antenna, a circular slot is loaded on circular patch and a square slot is etched on the ground plane of
dimension 30mm×30mm. Design of the antenna is carried out using CST Microsoft Studio Sonimulation
Software. The proposed antenna resonates at 5.5 GHz with a wider bandwidth of 702 MHz and it provides
low return loss of -31.58 dB, good gain of 3.23 dB and directivity of 4.28 dBi and high efficiency of around
79% against the resonance frequency. The geometry of the proposed circular antenna with reduced size
and its various performance parameters such as return loss, bandwidth, VSWR, gain, directivity, efficiency
and radiation pattern plots are presented and discussed.
DESIGN OF A COMPACT CIRCULAR MICROSTRIP PATCH ANTENNA FOR WLAN APPLICATIONSpijans
This paper presents the design of a compact circular microstrip patch antenna for WLAN applications
which covers the band 5.15 to 5.825 GHz. The antenna is designed using 1.4mm thick FR-4
(lossy)substrate with relative permittivity 4.4 and a microstrip line feed is used. The radius of the
circular patch is chosen as 7.62mm. To reduce the size and enhance the performance of the proposed
antenna, a circular slot is loaded on circular patch and a square slot is etched on the ground plane of
dimension 30mm×30mm. Design of the antenna is carried out using CST Microsoft Studio Sonimulation
Software. The proposed antenna resonates at 5.5 GHz with a wider bandwidth of 702 MHz and it provides
low return loss of -31.58 dB, good gain of 3.23 dB and directivity of 4.28 dBi and high efficiency of around
79% against the resonance frequency. The geometry of the proposed circular antenna with reduced size
and its various performance parameters such as return loss, bandwidth, VSWR, gain, directivity, efficiency
and radiation pattern plots are presented and discussed
Design and Analysis of MIMO Patch Antenna for 5G Wireless Communication SystemsIJCNCJournal
In this work, the circular array microstrip patch antenna (MPA) design is proposed for the 5G wireless communication and the millimeter- wave frequency being utilized for this communication system to enhance the coverage area. Here, the Multi Input Multi Output feeding technique is utilized to improve the performance of the proposed design at a resonant frequency of 35 GHz with RT-Duroid 5880 material as substrate. It has 2.2 dielectric constant value and the thickness is 0.5mm.The simulation analysis has obtained the gain as 8.8dB and return loss as -41.9dB. Also, two MPA designs such as single element MPA and 2x2 rectangular array MPA are designed to validate the proposed antenna design. A comparative analysis has proved that the circular array MPA is preferable for the 5G wireless communication system compared to the other two designs such as single element MPA and 2x2 rectangular array MPA.
DESIGN AND ANALYSIS OF MIMO PATCH ANTENNA FOR 5G WIRELESS COMMUNICATION SYSTEMSIJCNCJournal
In this work, the circular array microstrip patch antenna (MPA) design is proposed for the 5G wireless
communication and the millimeter- wave frequency being utilized for this communication system to
enhance the coverage area. Here, the Multi Input Multi Output feeding technique is utilized to improve the
performance of the proposed design at a resonant frequency of 35 GHz with RT-Duroid 5880 material as
substrate. It has 2.2 dielectric constant value and the thickness is 0.5mm.The simulation analysis has
obtained the gain as 8.8dB and return loss as -41.9dB. Also, two MPA designs such as single element MPA
and 2x2 rectangular array MPA are designed to validate the proposed antenna design. A comparative
analysis has proved that the circular array MPA is preferable for the 5G wireless communication system
compared to the other two designs such as single element MPA and 2x2 rectangular array MPA.
Impact and analytical study of the patch and slot for antenna designeSAT Journals
Abstract Antenna is the backbone of the communication system. With the advent of technology a lot of innovation happens to develop the antennas. Antenna is a smart device, which not only transmit and receive but also works as a transducer. S/N ratio also Abstract depend upon the efficiency of the antenna .Patch and slot has become a very important in modern wireless communication antennas. Patch and slots are being used for performance improvement of antenna in wireless communication. with the pace and speed of the communication theory, antennas also its design also developed in an innovative ways. Keeping the above fact in mind we had tried to present a complete review on patch and slots antennas .it has been analyzed in detail, In different size and shapes of slots and patch are great interest of obtaining optimum results of antenna design , in order to allow their use in communication application. A variety of the antennas are available in the communication engineering system. Present study represent the various details and open wide the slit for more innovations. Keywords- ( patch, slot GSM900, GSM1800, GSM 2100, UMTS, IMT-2000 and PCS,
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
Microstrip Rectangular Monopole Antennas with Defected Ground for UWB Applica...IJECEIAES
This paper presents the design of new compact antennas for ultra wide band applications. Each antenna consists of a rectangular patch fed by 50Ω microstrip transmission line and the ground element is a defected ground structure (DGS). The aim of this study is to improve the bandwidth of these antennas by using DGS and the modification geometry of rectangular structure, which gives new compact antennas for UWB applications. The input impedance bandwidth of the antennas with S11<-10dB is more than 10GHz, from 3GHz to more than 14 GHz. The proposed antennas are investigated and optimized by using CST microwave studio, they are validated by using another electromagnetic solver Ansoft HFSS. The measured parameters present good agreement with simulation. The final antenna structures offer excellent performances for UWB system.
Design of high gain dual T-shaped stub antenna for satellite communicationTELKOMNIKA JOURNAL
The ultra wide band (UWB) antennas play a vital role in supporting different wireless standards and are suitable for wide variety of applications. This paper is aimed to present a novel UWB dual notch microstrip antenna with modified ground plane. The antenna is designed to operate in UWB ranging from 2 GHz to 12 GHz with multi band operation. This will help in operating the antenna for different operations independently. The proposed structure will operate in two notch bands 3.3-4 GHz (Wi-MAX), 5.05-5.9 GHz (WLAN) and the structure is suitable for long distance communications because of its increased directivity. The structure can also be used for X-Band applications for various applications of traffic control, weather forecasting and vehicle speed detection systems. It is observed that, the proposed structure is offering a gain of 5.2 dBi with improved directivity with a beam width of 42.230. This makes the antenna structure suitable for long distance satellite communications. The antenna is supporting the circular polarization at higher the frequencies and can be useful for the upcoming 5G mobile applications. Moreover, the proposed structure offers the less interference at the receiver. The structure is found to be smaller in dimensions, easily fabricated at low costs and can be integrated into any compact wireless devices. The structure is simulated using a commercially available software Ansys-HFSS and is analyzed.
Design and optimization of a rectangular microstrip patch antenna for dual-b...IJECEIAES
This paper introduces a new rectangular slot antenna structure based on a simple rectangular shape with two symmetrical rectangular slots on the radiated element. The aim of this work is to design an antenna and enhance it to function in the band (2.45 GHz and 5.8 GHz). We formulated the dimensions of the antenna using the transmission line model of the analytical methods and then we optimized these parameters using the CST Microwave Studio simulator. We made changes to two important parameters in our design: the position and width of the slots when the other parameters are kept constant. The resulting antenna provides good adaptation, high gain that achieves 5.96 dBi at 2.45 GHz and 6.491 dBi at 5.8 GHz, good return loss values of -49.859 dB and -34.303 dB for the lower and upper operating frequencies respectively. For radio frequency identification (RFID) implementations, the proposed antenna is ideal, and its main advantage is that it has high gain and is simple to design and fabricate.
Modified T&U Shape Triangular Microstrip Patch Antenna Array for Communication.IJSRD
Modern communication system requires high gain, large bandwidth and less size antennas which shows excellent performance over a wide range of frequency spectrum. Proposed system uses FR4 as a dielectric substrate(€r=4.4).Proposed Triangular Miscrostrip Patch antenna is designed with additional T & U shape ,simulated by using high frequency simulation software HFSS & finally tested with the help of vector network analyzer (VNA -N9923A) . Various antenna parameters like Return Loss, Gain and VSWR etc. are calculated using HFSS. The antenna has been designed to operate on the range of 5.5GHz. This paper report the simulation result using equilateral triangular patch antenna with Microstrip line feed.
A PATCH ANTENNA DESIGN WITH BOOSTED BANDWIDTH FOR ISM BAND APPLICATIONSpijans
In recent times, the utilization of microstrip patch antennas (MPAs) has increased due to their simple
production, simple analysis, low cost, lightweight, easy feeding, and superior radiation characteristics.
Limited bandwidth is a key disadvantage of MPAs. In this paper, a rectangular patch antenna with partial
ground plane (PGP) strategy for ISM applications is proposed to overcome this deficiency and its
performance is compared with that of a traditional patch antenna. A low-cost FR-4 substrate with a
dielectric constant of 4.3 and a thickness of 1.6 mm is used to make both antennas designed. The antennas
are analyzed and simulated at the operating frequency of 2.45 GHz using CST software. The simulation
results show that the proposed antenna has a 0.1465 GHz i.e. 146.5 MHz bandwidth, which is more than
1.77 times larger than a conventional antenna (bandwidth = 0.0827 GHz i.e. 82.7MHz). The suggested
antenna is suitable for a wide range of wireless communication standards, such as Bluetooth (2.4 to 2.485
GHz), WiMAX (2.3 to 2.4 GHz), Microwave ovens (2.4 to 2.48 GHz), RFID (2.4 to 2.5 GHz), S-Band (2.3
to 2.4 GHz), Wireless Communication Services (WCS) 2.345 GHz to 2.360 GHz, and 4G LTE (2.3 to 2.315
GHz).
A PATCH ANTENNA DESIGN WITH BOOSTED BANDWIDTH FOR ISM BAND APPLICATIONSpijans
In recent times, the utilization of microstrip patch antennas (MPAs) has increased due to their simple
production, simple analysis, low cost, lightweight, easy feeding, and superior radiation characteristics.
Limited bandwidth is a key disadvantage of MPAs. In this paper, a rectangular patch antenna with partial
ground plane (PGP) strategy for ISM applications is proposed to overcome this deficiency and its
performance is compared with that of a traditional patch antenna. A low-cost FR-4 substrate with a
dielectric constant of 4.3 and a thickness of 1.6 mm is used to make both antennas designed. The antennas
are analyzed and simulated at the operating frequency of 2.45 GHz using CST software. The simulation
results show that the proposed antenna has a 0.1465 GHz i.e. 146.5 MHz bandwidth, which is more than
1.77 times larger than a conventional antenna (bandwidth = 0.0827 GHz i.e. 82.7MHz). The suggested
antenna is suitable for a wide range of wireless communication standards, such as Bluetooth (2.4 to 2.485
GHz), WiMAX (2.3 to 2.4 GHz), Microwave ovens (2.4 to 2.48 GHz), RFID (2.4 to 2.5 GHz), S-Band (2.3
to 2.4 GHz), Wireless Communication Services (WCS) 2.345 GHz to 2.360 GHz, and 4G LTE (2.3 to 2.315
GHz).
Understanding Inductive Bias in Machine LearningSUTEJAS
This presentation explores the concept of inductive bias in machine learning. It explains how algorithms come with built-in assumptions and preferences that guide the learning process. You'll learn about the different types of inductive bias and how they can impact the performance and generalizability of machine learning models.
The presentation also covers the positive and negative aspects of inductive bias, along with strategies for mitigating potential drawbacks. We'll explore examples of how bias manifests in algorithms like neural networks and decision trees.
By understanding inductive bias, you can gain valuable insights into how machine learning models work and make informed decisions when building and deploying them.
The Internet of Things (IoT) is a revolutionary concept that connects everyday objects and devices to the internet, enabling them to communicate, collect, and exchange data. Imagine a world where your refrigerator notifies you when you’re running low on groceries, or streetlights adjust their brightness based on traffic patterns – that’s the power of IoT. In essence, IoT transforms ordinary objects into smart, interconnected devices, creating a network of endless possibilities.
Here is a blog on the role of electrical and electronics engineers in IOT. Let's dig in!!!!
For more such content visit: https://nttftrg.com/
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
Harnessing WebAssembly for Real-time Stateless Streaming PipelinesChristina Lin
Traditionally, dealing with real-time data pipelines has involved significant overhead, even for straightforward tasks like data transformation or masking. However, in this talk, we’ll venture into the dynamic realm of WebAssembly (WASM) and discover how it can revolutionize the creation of stateless streaming pipelines within a Kafka (Redpanda) broker. These pipelines are adept at managing low-latency, high-data-volume scenarios.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
Hierarchical Digital Twin of a Naval Power SystemKerry Sado
A hierarchical digital twin of a Naval DC power system has been developed and experimentally verified. Similar to other state-of-the-art digital twins, this technology creates a digital replica of the physical system executed in real-time or faster, which can modify hardware controls. However, its advantage stems from distributing computational efforts by utilizing a hierarchical structure composed of lower-level digital twin blocks and a higher-level system digital twin. Each digital twin block is associated with a physical subsystem of the hardware and communicates with a singular system digital twin, which creates a system-level response. By extracting information from each level of the hierarchy, power system controls of the hardware were reconfigured autonomously. This hierarchical digital twin development offers several advantages over other digital twins, particularly in the field of naval power systems. The hierarchical structure allows for greater computational efficiency and scalability while the ability to autonomously reconfigure hardware controls offers increased flexibility and responsiveness. The hierarchical decomposition and models utilized were well aligned with the physical twin, as indicated by the maximum deviations between the developed digital twin hierarchy and the hardware.
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...Amil Baba Dawood bangali
Contact with Dawood Bhai Just call on +92322-6382012 and we'll help you. We'll solve all your problems within 12 to 24 hours and with 101% guarantee and with astrology systematic. If you want to take any personal or professional advice then also you can call us on +92322-6382012 , ONLINE LOVE PROBLEM & Other all types of Daily Life Problem's.Then CALL or WHATSAPP us on +92322-6382012 and Get all these problems solutions here by Amil Baba DAWOOD BANGALI
#vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore#blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #blackmagicforlove #blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #Amilbabainuk #amilbabainspain #amilbabaindubai #Amilbabainnorway #amilbabainkrachi #amilbabainlahore #amilbabaingujranwalan #amilbabainislamabad
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
NUMERICAL SIMULATIONS OF HEAT AND MASS TRANSFER IN CONDENSING HEAT EXCHANGERS...ssuser7dcef0
Power plants release a large amount of water vapor into the
atmosphere through the stack. The flue gas can be a potential
source for obtaining much needed cooling water for a power
plant. If a power plant could recover and reuse a portion of this
moisture, it could reduce its total cooling water intake
requirement. One of the most practical way to recover water
from flue gas is to use a condensing heat exchanger. The power
plant could also recover latent heat due to condensation as well
as sensible heat due to lowering the flue gas exit temperature.
Additionally, harmful acids released from the stack can be
reduced in a condensing heat exchanger by acid condensation. reduced in a condensing heat exchanger by acid condensation.
Condensation of vapors in flue gas is a complicated
phenomenon since heat and mass transfer of water vapor and
various acids simultaneously occur in the presence of noncondensable
gases such as nitrogen and oxygen. Design of a
condenser depends on the knowledge and understanding of the
heat and mass transfer processes. A computer program for
numerical simulations of water (H2O) and sulfuric acid (H2SO4)
condensation in a flue gas condensing heat exchanger was
developed using MATLAB. Governing equations based on
mass and energy balances for the system were derived to
predict variables such as flue gas exit temperature, cooling
water outlet temperature, mole fraction and condensation rates
of water and sulfuric acid vapors. The equations were solved
using an iterative solution technique with calculations of heat
and mass transfer coefficients and physical properties.