Tank radar set up
•Download as DOCX, PDF•
1 like•70 views
This document provides instructions for setting up tank radar and radar master software: 1. Connect the Hart communicator to the radar and select basic setup to input measurements like tank dimensions and material properties. Offset the radar level reading to match the hand gauge measurement. 2. Install a 250 ohm resistor in the radar power supply circuit for HART communications. Connect the Hart communicator leads on either side. 3. Open the radar master software, set the communication settings to connect to the HART communicator port, and scan to find the instrument. Then use the setup wizard to input the radar configuration.
Report
Share
Report
Share
Recommended
How to make test boxes
This document provides instructions for building three test devices: a break out box to connect cables and measure voltage, frequency, current, and simulate 4-20 mA and frequency signals; a 4-20 mA simulator using a resistor and light switch to demonstrate current levels; and a pressure transducer tester using a 9V battery and switch to calibrate transducers at 3.9 mA and 19.9 mA readings. Connectors, test points, and components are soldered together to construct the boxes, which are used with a digital meter to test and troubleshoot process instrumentation.
How to trouble shoot frac pump transmission problems
This document provides tips for troubleshooting transmission problems in frac pumps. It discusses checking solenoids, relays, sensors, and other components. Key points include:
- Measuring solenoid resistance to identify issues
- Checking for locked transmission which could overheat from a bad lock up solenoid
- Testing pressure switches and sensors that may cause transmission errors
- Resetting control modules and codes to resolve many problems
- Providing wiring diagrams and specifications for Allison transmissions
How to calibrate a frac pump and data
This document provides instructions for calibrating a frac pump and data van pressure transducer using a two-point calibration method. It explains how to set the minimum and maximum scale readings using calibration pins on the pump control panel. The calibration process involves setting the zero point with little pressure on the pump and setting the full scale point while holding the calibration switch. It also describes how to calibrate data van wellhead pressure transducers using software to set the zero pressure at 4mA and high pressure point at 20mA. Finally, it discusses using transducer slope instead of a fixed maximum pressure for calibration in some software programs.
Frac turbine flow meters and mag meters
Turbine and electromagnetic (mag) flow meters are used to measure suction and discharge rates on blenders. Turbine flow meters require a calibration factor that should be attached to the meter or rebuild kit. For low flow rates, a 4-inch meter is better than an 8-inch meter. Turbine meters wear out over time but can be rebuilt. Mag meters use flow tube tag information to program the transmitter. Pie frequency generators and LCR meters can be used to troubleshoot mag meters. Manuals provide instructions for setup, programming, and troubleshooting of mag meters.
Frac data van acquisition system test
This document provides instructions for testing a data acquisition system using simulation tools. It describes how to create a test job in frac software like IFS, connect a laptop running ACE to an instrument skid via Ethernet to simulate pressure and rate inputs, and generate graphs in IFS to verify the simulated data is recording properly. Key tools mentioned include a loop calibrator to simulate pressure and a function generator for simulating rate. The test allows verifying communication between field equipment, data van software, and central servers.
How to test calibration of pressure transmitters and
- Pressure transmitters and switches can be tested using a crystal meter connected to a hydraulic hand pump. The crystal meter displays current and pressure readings.
- The hand pump is used to pressurize the transmitter or switch being tested. The crystal meter records the current and pressure at specific calibration points to check if the transmitter is properly calibrated.
- Differential pressure transmitters can also be tested using a differential pressure manifold connected to the hand pump. Various valves on the manifold are opened and closed to test across the pressure difference.
- Pressure switches are tested by applying pressure from the hand pump and monitoring when the switch contact opens at the setpoint pressure. The crystal meter shows the switch changing from closed to open.
Electrical calibration workload matrix
This document provides a comparison of Fluke calibration products. It lists various product models and their key specifications and capabilities. The products include multifunction calibrators, oscilloscope calibrators, precision process calibrators, data acquisition modules, and safety testers. Specifications covered include voltage, current and resistance measurement accuracy, temperature simulation and measurement capabilities, pressure modules, oscilloscope channels and bandwidth, and electrical safety testing functions. The matrix is intended to help users determine which Fluke calibration products best suit their needs.
Four Quadrant Metering
Four quadrant metering can be used to understand individually or collectively:
Real Power consumed by the end user
Apparent Power delivered by the utility
Real Power delivered to the utility by an end user’s generation source
Apparent Power generated by the end user’s generation source
Having these measurements allows for the calculation of Reactive Power, VA and VARS as well as providing kWh for billing purposes.
Recommended
How to make test boxes
This document provides instructions for building three test devices: a break out box to connect cables and measure voltage, frequency, current, and simulate 4-20 mA and frequency signals; a 4-20 mA simulator using a resistor and light switch to demonstrate current levels; and a pressure transducer tester using a 9V battery and switch to calibrate transducers at 3.9 mA and 19.9 mA readings. Connectors, test points, and components are soldered together to construct the boxes, which are used with a digital meter to test and troubleshoot process instrumentation.
How to trouble shoot frac pump transmission problems
This document provides tips for troubleshooting transmission problems in frac pumps. It discusses checking solenoids, relays, sensors, and other components. Key points include:
- Measuring solenoid resistance to identify issues
- Checking for locked transmission which could overheat from a bad lock up solenoid
- Testing pressure switches and sensors that may cause transmission errors
- Resetting control modules and codes to resolve many problems
- Providing wiring diagrams and specifications for Allison transmissions
How to calibrate a frac pump and data
This document provides instructions for calibrating a frac pump and data van pressure transducer using a two-point calibration method. It explains how to set the minimum and maximum scale readings using calibration pins on the pump control panel. The calibration process involves setting the zero point with little pressure on the pump and setting the full scale point while holding the calibration switch. It also describes how to calibrate data van wellhead pressure transducers using software to set the zero pressure at 4mA and high pressure point at 20mA. Finally, it discusses using transducer slope instead of a fixed maximum pressure for calibration in some software programs.
Frac turbine flow meters and mag meters
Turbine and electromagnetic (mag) flow meters are used to measure suction and discharge rates on blenders. Turbine flow meters require a calibration factor that should be attached to the meter or rebuild kit. For low flow rates, a 4-inch meter is better than an 8-inch meter. Turbine meters wear out over time but can be rebuilt. Mag meters use flow tube tag information to program the transmitter. Pie frequency generators and LCR meters can be used to troubleshoot mag meters. Manuals provide instructions for setup, programming, and troubleshooting of mag meters.
Frac data van acquisition system test
This document provides instructions for testing a data acquisition system using simulation tools. It describes how to create a test job in frac software like IFS, connect a laptop running ACE to an instrument skid via Ethernet to simulate pressure and rate inputs, and generate graphs in IFS to verify the simulated data is recording properly. Key tools mentioned include a loop calibrator to simulate pressure and a function generator for simulating rate. The test allows verifying communication between field equipment, data van software, and central servers.
How to test calibration of pressure transmitters and
- Pressure transmitters and switches can be tested using a crystal meter connected to a hydraulic hand pump. The crystal meter displays current and pressure readings.
- The hand pump is used to pressurize the transmitter or switch being tested. The crystal meter records the current and pressure at specific calibration points to check if the transmitter is properly calibrated.
- Differential pressure transmitters can also be tested using a differential pressure manifold connected to the hand pump. Various valves on the manifold are opened and closed to test across the pressure difference.
- Pressure switches are tested by applying pressure from the hand pump and monitoring when the switch contact opens at the setpoint pressure. The crystal meter shows the switch changing from closed to open.
Electrical calibration workload matrix
This document provides a comparison of Fluke calibration products. It lists various product models and their key specifications and capabilities. The products include multifunction calibrators, oscilloscope calibrators, precision process calibrators, data acquisition modules, and safety testers. Specifications covered include voltage, current and resistance measurement accuracy, temperature simulation and measurement capabilities, pressure modules, oscilloscope channels and bandwidth, and electrical safety testing functions. The matrix is intended to help users determine which Fluke calibration products best suit their needs.
Four Quadrant Metering
Four quadrant metering can be used to understand individually or collectively:
Real Power consumed by the end user
Apparent Power delivered by the utility
Real Power delivered to the utility by an end user’s generation source
Apparent Power generated by the end user’s generation source
Having these measurements allows for the calculation of Reactive Power, VA and VARS as well as providing kWh for billing purposes.
TESCO Tuesday: CT Testing: Theory and Practice
This presentation discusses self-contained vs. transformer rated CTs, functions and terminology, CT testing, ratio testing, burden testing, and more.
Starter Motor diagnostic
This diagnostic worksheet outlines steps to determine if a starter motor has an issue and help prevent unwarranted warranty denials. The steps include: 1) checking each battery has at least 75% charge and the voltage difference between batteries is no more than 0.1 volts; 2) testing battery cables for resistance less than 2mΩ or voltage drop less than 1 volt under load; 3) checking relay voltage is at least 11.4v when turning the key to crank; and 4) if voltage is over 11.4v but starter does not engage, replace the starter.
How to identify and solve the problem that piezoelectric products unable to a...
Hello everyone, today professional CoreMorrow engineer will introduce the identification and solutions for piezoelectric products that cannot be used in closed loop due to zero offset.
TESCO Tuesday: Transformer-Rated & Self-Contained Metering Fundamentals
TESCO Tuesday: Transformer-Rated & Self-Contained Metering FundamentalsTESCO - The Eastern Specialty Company
This document discusses transformer-rated metering fundamentals, including:
- Transformer-rated meters measure current through current transformers and sometimes voltage transformers, unlike self-contained meters which connect directly to the load.
- Blondel's theorem states that total power in a polyphase system can be measured using N-1 meters connected between each line and a common point.
- Meeting Blondel's theorem ensures accurate power measurements under all conditions, while violations may cause errors if voltage and current are not balanced.
- Examples show how to apply Blondel's theorem correctly for 3-phase 4-wire systems.TESCO Tuesday: Ratio, Burden and Admittance
This document provides an overview and agenda for an advanced training session on field CT testing. It discusses the key topics of ratio, burden, and admittance testing to evaluate the functionality and health of current transformers (CTs). The summary discusses:
- Ratio testing measures the proportional relationship between primary and secondary currents.
- Burden testing checks that CTs maintain accurate ratios with varying levels of burden on the secondary loop, up to specified limits.
- Admittance testing uses injected audio signals to evaluate the overall "health" of the CT's secondary loop in millisiemens values. Interpreting the results requires analysis to understand implications.
- Demagnetization procedures are also covered to address issues like
Vom reading
This document provides safety guidelines and instructions for using a volt-ohm meter (VOM) to take electrical measurements. Key points include:
1) Always select the highest range setting if unsure of the measurement value to avoid meter damage. Take readings near the center of the analog scale for best accuracy.
2) Never hold the meter in your hand or touch live circuits when taking measurements. Use a clamp-on meter for currents over 250mA and wear protective equipment like safety glasses.
3) Examples are given for converting readings to the correct voltage values based on the range setting and scale. Readings must be multiplied or decimal points adjusted depending on the range/scale combination.
KEMET Webinar - Measuring capacitors properties correct
This document discusses measuring capacitor properties correctly. It begins by outlining standards for measuring capacitors and common equipment used like DMMs, RLC bridges, and vector network analyzers. Key points covered include only being able to directly measure voltage, current, and phase between them. Capacitance, inductance, and resistance must be calculated from these measurements based on the impedance. It reviews measurement principles for ceramic, polymer, and tantalum capacitors according to EIA-198-D standards. The importance of measuring at the specified AC voltage and DC bias is emphasized to avoid incorrect readings caused by capacitance shifts. Different measurement techniques for low-Z and high-Z capacitors are presented, including using series and
Lab 2 multimeter
A multimeter is an electronic instrument that combines several measurement functions in one unit, allowing it to measure voltage, current, and resistance. An analog multimeter uses a moving pointer on a calibrated scale to display measurements, while a digital multimeter converts measurements to a digital number. This document provides instructions on using an analog multimeter to take voltage, current, and resistance measurements. It explains how to properly connect the probes and select ranges, as well as how to accurately read measurements on the analog scale.
Traditional Ratio, Burden, Admittance and Demag Testing – Part I
Traditional Ratio, Burden, Admittance and Demag Testing – Part ITESCO - The Eastern Specialty Company
Part I gives a quick overview on ratio/burden testing and a more in-depth look at using traditional burden test sets.
Hands-On Transformer Rated Polyphase Meter Testing
This presentation discusses the differences between self-contained and transformer or instrument rated meter sites; transformer rated meter forms; test switches and CTs; meter accuracy testing in the field; checking the health of your CTs and PTs; and Site Verification. This presentation was given at the MEUA Meter School. 03/03/20
Ratio, Burden, Admittance Testing
This presentation was for an Advanced Session at North Carolina Meter School and discussed CT functionality Basics, Terminology and Specifications, Ratio Testing, Burden Testing, Admittance Testing, and Demag Functions.
Wb4-3
This document discusses potentiometers and their use in electronic circuits. Potentiometers are variable resistors that can be used as voltage dividers to provide an output voltage that is a fraction of the supply voltage. Proper resistor values are needed to avoid loading errors that occur when the resistance connected to the potentiometer output is too low compared to the potentiometer resistance. Potentiometers are also used in temperature sensors, strain gauges, and other electronic applications.
EV Charging Stations
Did you know vehicle manufacturers have announced over 100 electric vehicle models are to be introduced by 2024? This presentation was given at the Southeastern Distribution Apparatus School in Auburn, AL and covers Electric Vehicle Service Equipment (EVSE) and the testing of Electric Vehicle stations. This presentation covers types of EVSEs, market growth, regulatory environment and type approval and testing.
Meter Shunt (Ammeter)
The document shows the step-by-step working to calculate the value of a shunt resistor used with a moving coil meter that has an internal resistance of 12 ohms and a full scale deflection of 22mA, when measuring a current of 40A. It calculates the shunt resistor value to be 0.0132 ohms.
Introduction to CTs and PTs
This presentation was given at the PREA Meter School and gives an introduction into current transformers and potential transformers. 03/10/20.
Force Measurement - Best load cell calibration practices
Common Measurement Errors, and Challenges on CMC uncertainty for Force Measurements This slide show presents some of the most common errors for force calibration. This would include, certificate errors, adapter issues, load cell errors, force sensor alignment issues, Dillon load link errors and more.
Ammeter&voltmeter
This document discusses different types of electronic ammeters and voltmeters. It describes the basic components and operating principles of basic ammeters, multirange ammeters, basic voltmeters, multirange voltmeters, electronic voltmeters including vacuum tube voltmeters and transistor voltmeters. Numerical examples are provided to illustrate how to calculate shunt resistances for converting a meter movement into different current ranges for an ammeter and multiplier resistances for extending the voltage range of a voltmeter.
MSC SOW
AFES will perform preventive maintenance of 11kV switchgear, transformers, and cables at various hub and MSC sites. This will include detailed inspections, testing, cleaning, servicing, and checking of components like circuit breakers, relays, meters, bushings, terminals, nuts/bolts, cables, and fuses. Proper operation and calibration of equipment will be ensured through simulated tests under working conditions.
Theorms
This document describes procedures to verify Thevenin's theorem and the superposition theorem. For Thevenin's theorem, the circuit is connected in different configurations to measure open circuit voltage, short circuit current, and load current. These values are used to calculate the Thevenin equivalent resistance and voltage, and compared to observed load current. For superposition theorem, the circuit is connected with individual sources to measure individual currents, which are summed and compared to total observed current. Readings are taken for multiple input values to verify the theorems. Calculations of individual currents and resistances are also described.
Digital voltmeter (DVM) and its Classification
This document discusses digital voltmeters (DVMs). It explains that DVMs display voltage measurements as numerical readings rather than using an analog needle gauge. The document covers various types of DVMs including ramp type, dual slope integrating type, successive approximation type, and microprocessor-based versions. It provides block diagrams and explanations of the operating principles for different DVM designs. Advantages of DVMs like accuracy, ease of reading, and versatility are also summarized.
High frequency radar level meter zero902
The document describes a 26GHz radar level meter. Key details:
- It uses radar technology to measure liquid levels up to 30 meters.
- The small antenna allows installation in tight spaces and is unaffected by dust or vapor.
- It has various process connections, approvals for hazardous areas, output options, and can be calibrated on-site or with a handheld programmer.
- Installation requirements include minimum distances from walls and ensuring the antenna is vertical for accurate readings.
RD-FMF12-T Radar level transmitter for rive and lakes
RD-FMF12-T Radar level transmitter for rive and lakesDalian Zero Instrument Technology Co., Ltd China
Application: Rivers, Lakes, Shoal
Measuring Range: 50 meters
Process Connection: Gantry frame/locking flange from DN65/2.5"
Temperature: -40℃ ~ 80℃
Process Pressure: -0.1~0.3 MPa
Precision: ± 2mm
Frequency Range: 120GHz
Protection Grade: IP68
Power Supply: (12 - 24V) DC / Four-wire
The Signal output: RS485
Debugging: Bluetooth / Modbus protocol
The Scene Display: NO
Shell: Plastic PVDFMore Related Content
What's hot
TESCO Tuesday: CT Testing: Theory and Practice
This presentation discusses self-contained vs. transformer rated CTs, functions and terminology, CT testing, ratio testing, burden testing, and more.
Starter Motor diagnostic
This diagnostic worksheet outlines steps to determine if a starter motor has an issue and help prevent unwarranted warranty denials. The steps include: 1) checking each battery has at least 75% charge and the voltage difference between batteries is no more than 0.1 volts; 2) testing battery cables for resistance less than 2mΩ or voltage drop less than 1 volt under load; 3) checking relay voltage is at least 11.4v when turning the key to crank; and 4) if voltage is over 11.4v but starter does not engage, replace the starter.
How to identify and solve the problem that piezoelectric products unable to a...
Hello everyone, today professional CoreMorrow engineer will introduce the identification and solutions for piezoelectric products that cannot be used in closed loop due to zero offset.
TESCO Tuesday: Transformer-Rated & Self-Contained Metering Fundamentals
TESCO Tuesday: Transformer-Rated & Self-Contained Metering FundamentalsTESCO - The Eastern Specialty Company
This document discusses transformer-rated metering fundamentals, including:
- Transformer-rated meters measure current through current transformers and sometimes voltage transformers, unlike self-contained meters which connect directly to the load.
- Blondel's theorem states that total power in a polyphase system can be measured using N-1 meters connected between each line and a common point.
- Meeting Blondel's theorem ensures accurate power measurements under all conditions, while violations may cause errors if voltage and current are not balanced.
- Examples show how to apply Blondel's theorem correctly for 3-phase 4-wire systems.TESCO Tuesday: Ratio, Burden and Admittance
This document provides an overview and agenda for an advanced training session on field CT testing. It discusses the key topics of ratio, burden, and admittance testing to evaluate the functionality and health of current transformers (CTs). The summary discusses:
- Ratio testing measures the proportional relationship between primary and secondary currents.
- Burden testing checks that CTs maintain accurate ratios with varying levels of burden on the secondary loop, up to specified limits.
- Admittance testing uses injected audio signals to evaluate the overall "health" of the CT's secondary loop in millisiemens values. Interpreting the results requires analysis to understand implications.
- Demagnetization procedures are also covered to address issues like
Vom reading
This document provides safety guidelines and instructions for using a volt-ohm meter (VOM) to take electrical measurements. Key points include:
1) Always select the highest range setting if unsure of the measurement value to avoid meter damage. Take readings near the center of the analog scale for best accuracy.
2) Never hold the meter in your hand or touch live circuits when taking measurements. Use a clamp-on meter for currents over 250mA and wear protective equipment like safety glasses.
3) Examples are given for converting readings to the correct voltage values based on the range setting and scale. Readings must be multiplied or decimal points adjusted depending on the range/scale combination.
KEMET Webinar - Measuring capacitors properties correct
This document discusses measuring capacitor properties correctly. It begins by outlining standards for measuring capacitors and common equipment used like DMMs, RLC bridges, and vector network analyzers. Key points covered include only being able to directly measure voltage, current, and phase between them. Capacitance, inductance, and resistance must be calculated from these measurements based on the impedance. It reviews measurement principles for ceramic, polymer, and tantalum capacitors according to EIA-198-D standards. The importance of measuring at the specified AC voltage and DC bias is emphasized to avoid incorrect readings caused by capacitance shifts. Different measurement techniques for low-Z and high-Z capacitors are presented, including using series and
Lab 2 multimeter
A multimeter is an electronic instrument that combines several measurement functions in one unit, allowing it to measure voltage, current, and resistance. An analog multimeter uses a moving pointer on a calibrated scale to display measurements, while a digital multimeter converts measurements to a digital number. This document provides instructions on using an analog multimeter to take voltage, current, and resistance measurements. It explains how to properly connect the probes and select ranges, as well as how to accurately read measurements on the analog scale.
Traditional Ratio, Burden, Admittance and Demag Testing – Part I
Traditional Ratio, Burden, Admittance and Demag Testing – Part ITESCO - The Eastern Specialty Company
Part I gives a quick overview on ratio/burden testing and a more in-depth look at using traditional burden test sets.
Hands-On Transformer Rated Polyphase Meter Testing
This presentation discusses the differences between self-contained and transformer or instrument rated meter sites; transformer rated meter forms; test switches and CTs; meter accuracy testing in the field; checking the health of your CTs and PTs; and Site Verification. This presentation was given at the MEUA Meter School. 03/03/20
Ratio, Burden, Admittance Testing
This presentation was for an Advanced Session at North Carolina Meter School and discussed CT functionality Basics, Terminology and Specifications, Ratio Testing, Burden Testing, Admittance Testing, and Demag Functions.
Wb4-3
This document discusses potentiometers and their use in electronic circuits. Potentiometers are variable resistors that can be used as voltage dividers to provide an output voltage that is a fraction of the supply voltage. Proper resistor values are needed to avoid loading errors that occur when the resistance connected to the potentiometer output is too low compared to the potentiometer resistance. Potentiometers are also used in temperature sensors, strain gauges, and other electronic applications.
EV Charging Stations
Did you know vehicle manufacturers have announced over 100 electric vehicle models are to be introduced by 2024? This presentation was given at the Southeastern Distribution Apparatus School in Auburn, AL and covers Electric Vehicle Service Equipment (EVSE) and the testing of Electric Vehicle stations. This presentation covers types of EVSEs, market growth, regulatory environment and type approval and testing.
Meter Shunt (Ammeter)
The document shows the step-by-step working to calculate the value of a shunt resistor used with a moving coil meter that has an internal resistance of 12 ohms and a full scale deflection of 22mA, when measuring a current of 40A. It calculates the shunt resistor value to be 0.0132 ohms.
Introduction to CTs and PTs
This presentation was given at the PREA Meter School and gives an introduction into current transformers and potential transformers. 03/10/20.
Force Measurement - Best load cell calibration practices
Common Measurement Errors, and Challenges on CMC uncertainty for Force Measurements This slide show presents some of the most common errors for force calibration. This would include, certificate errors, adapter issues, load cell errors, force sensor alignment issues, Dillon load link errors and more.
Ammeter&voltmeter
This document discusses different types of electronic ammeters and voltmeters. It describes the basic components and operating principles of basic ammeters, multirange ammeters, basic voltmeters, multirange voltmeters, electronic voltmeters including vacuum tube voltmeters and transistor voltmeters. Numerical examples are provided to illustrate how to calculate shunt resistances for converting a meter movement into different current ranges for an ammeter and multiplier resistances for extending the voltage range of a voltmeter.
MSC SOW
AFES will perform preventive maintenance of 11kV switchgear, transformers, and cables at various hub and MSC sites. This will include detailed inspections, testing, cleaning, servicing, and checking of components like circuit breakers, relays, meters, bushings, terminals, nuts/bolts, cables, and fuses. Proper operation and calibration of equipment will be ensured through simulated tests under working conditions.
Theorms
This document describes procedures to verify Thevenin's theorem and the superposition theorem. For Thevenin's theorem, the circuit is connected in different configurations to measure open circuit voltage, short circuit current, and load current. These values are used to calculate the Thevenin equivalent resistance and voltage, and compared to observed load current. For superposition theorem, the circuit is connected with individual sources to measure individual currents, which are summed and compared to total observed current. Readings are taken for multiple input values to verify the theorems. Calculations of individual currents and resistances are also described.
Digital voltmeter (DVM) and its Classification
This document discusses digital voltmeters (DVMs). It explains that DVMs display voltage measurements as numerical readings rather than using an analog needle gauge. The document covers various types of DVMs including ramp type, dual slope integrating type, successive approximation type, and microprocessor-based versions. It provides block diagrams and explanations of the operating principles for different DVM designs. Advantages of DVMs like accuracy, ease of reading, and versatility are also summarized.
What's hot (20)
How to identify and solve the problem that piezoelectric products unable to a...
How to identify and solve the problem that piezoelectric products unable to a...
TESCO Tuesday: Transformer-Rated & Self-Contained Metering Fundamentals
TESCO Tuesday: Transformer-Rated & Self-Contained Metering Fundamentals
KEMET Webinar - Measuring capacitors properties correct
KEMET Webinar - Measuring capacitors properties correct
Traditional Ratio, Burden, Admittance and Demag Testing – Part I
Traditional Ratio, Burden, Admittance and Demag Testing – Part I
Hands-On Transformer Rated Polyphase Meter Testing
Hands-On Transformer Rated Polyphase Meter Testing
Force Measurement - Best load cell calibration practices
Force Measurement - Best load cell calibration practices
Similar to Tank radar set up
High frequency radar level meter zero902
The document describes a 26GHz radar level meter. Key details:
- It uses radar technology to measure liquid levels up to 30 meters.
- The small antenna allows installation in tight spaces and is unaffected by dust or vapor.
- It has various process connections, approvals for hazardous areas, output options, and can be calibrated on-site or with a handheld programmer.
- Installation requirements include minimum distances from walls and ensuring the antenna is vertical for accurate readings.
RD-FMF12-T Radar level transmitter for rive and lakes
RD-FMF12-T Radar level transmitter for rive and lakesDalian Zero Instrument Technology Co., Ltd China
Application: Rivers, Lakes, Shoal
Measuring Range: 50 meters
Process Connection: Gantry frame/locking flange from DN65/2.5"
Temperature: -40℃ ~ 80℃
Process Pressure: -0.1~0.3 MPa
Precision: ± 2mm
Frequency Range: 120GHz
Protection Grade: IP68
Power Supply: (12 - 24V) DC / Four-wire
The Signal output: RS485
Debugging: Bluetooth / Modbus protocol
The Scene Display: NO
Shell: Plastic PVDF80G FM Radar Level Meter Product Manual
The general principle of the FM continuous wave radar level gauge is that the radar emits electromagnetic waves on the top of the tank, and the electromagnetic waves are received by the radar after being reflected by the medium. The frequency difference δf between the received signal and the transmitted signal is proportional to the distance R from the surface of the medium: R=C (speed)*δf (frequency difference)/2/K (frequency modulation slope). Because the speed of light C and the frequency modulation slope K are known, the frequency difference δf can be estimated to obtain the distance R from the radar installation position to the material surface, and then through the known total height of the tank, subtract the spatial distance from the radar to the material surface (referred to as Empty height) to get the height of the material level.
Varactor diode or varicap diode working and applications
A varactor diode is also called varicap diode. Lets look into the construction, working of diode, characteristics and applications of varactor diode
Steam flow meter- COMPAFLOW
Saturated/Superheated, Gas, Liquid…Flowmeter
Saturated/Superheated, Gas, Liquid…Flowmeter
Saturated/Superheated, Gas, Liquid…Flowmeter
-Saturated/Superheated Steam flow meter
-Gas flow meter
-Liquid flow meter
-ISO – 5167 Standard
-Low Cost
-Easy Installation
-High Accuracy
-Ready to connect to internet
-Not be affacted by vibration & electromagnetic interference
Thông tin liên lạc:
Nguyễn Văn Linh – Sales Engineer
Tel : +84-8-6268.2523 / 6268.2524 Ext 106
H/P: 0903.898.256 / 0988.880.426
Website: https://steamflowmeter.wordpress.com
Youtube: https://www.youtube.com/playlist?list=PL7OkPvAYND9z98UuZuBD8A8HJIaF3FMVj
Fb: https://www.facebook.com/tommymyteo
Mail: sales.05@daviteq.com / gblinh@gmail.com
phase 1 final drft.pptx
The document describes a proposed high-efficiency sea-water monopole antenna using an acrylic tube for maritime wireless communications. The antenna consists of a feeding probe and a sea-water cylinder held by a clear acrylic tube. This design aims to improve upon existing sea-water antennas by using a thicker sea-water cylinder for higher efficiency and an acrylic tube structure for transparency and reconfigurability. The objective is to develop this antenna to enable more effective wireless communication for submarines and water vessels.
Original N-Channel Mosfet IRFD120PBF 120 100V 1.3A DIP-4 New Vishay Siliconix
The document provides product specifications for the IRFD120 and SiHFD120 power MOSFETs from Vishay, including absolute maximum ratings, thermal characteristics, electrical characteristics and typical performance curves, with the MOSFETs offering features such as a 175°C operating temperature and fast switching for power applications.
Hydrometry: Field Manual, Field Application of ADCP Volume-4 Part V 2003
This document provides guidance on using Acoustic Doppler Current Profilers (ADCPs) for streamflow measurement in India. It discusses operating modes, site conditions, deployment, setup, and data handling procedures for ADCPs manufactured by RDI and SonTek. The key considerations outlined include selecting an appropriate operating mode based on water depth and velocity, deploying the ADCP from a boat, and setting parameters like bin size and blanking distance prior to measurement runs. Proper setup and handling of the ADCP equipment is important given its technical complexity and cost.
An9611
This document summarizes a DC-AC isolated battery inverter design that uses the HIP4082 integrated circuit. It describes the need for DC-AC inverters to provide backup power from batteries. The design uses the HIP4082 IC to generate a 60kHz square wave from the battery input to drive a transformer. It then rectifies and filters the output to produce a 55Hz quasi-square wave AC output. Key features of the HIP4082 IC that make it suitable for this application are also summarized, including its ability to independently drive four MOSFETs in a full-bridge configuration. The document provides details on the primary inverter design including the input filter, waveform generation, bootstrap supply,
Final esd lab manual (1)
Here are the key steps to design a variable gain audio amplifier using LM380:
1. The LM380 is an audio power amplifier that can provide a gain of up to 200. It is powered by a supply voltage between 4-15V.
2. A potentiometer is used to provide a variable gain from 1 to 50. The potentiometer is connected between the non-inverting and inverting inputs of the LM380. Turning the potentiometer varies the voltage division and thus the gain.
3. The audio input signal is given to the non-inverting terminal. A coupling capacitor is used to block any DC from the signal source and allow only the AC audio signal to pass.
EI 2406 instrumentation system design laboratory
The document provides details of experiments to be conducted in an Instrumentation Systems Design laboratory. It includes experiments to design instrumentation amplifiers, active filters, voltage/current converters, cold junction compensation circuits, signal conditioning circuits for RTDs and thermocouples, orifice plates, rotameters, control valves, and PID controllers using operational amplifiers and microprocessors. Circuit diagrams, equipment lists, procedures, and objectives are provided for each experiment.
Presentation_Power_Transformers-1
This document provides an overview of power transformers, including:
1. It describes different types of transformers such as power, distribution, auto, step-up, step-down transformers and discusses their various components and specifications.
2. It explains transformers used in power plants along with their ratings, cooling methods, impedance and other details.
3. It covers transformer components, testing procedures, loading capacity, condition monitoring techniques and diagnostic tests to evaluate transformer performance and health.
Advanced motion controls b12a6
The Analog Servo Drive B12A6 is a PWM servo drive designed to drive brushless DC motors. It has a peak current of 12A and continuous current of 6A, and operates on a supply voltage of 20-60VDC. It provides fully protected operation and interfaces with digital controllers or can operate standalone. It has adjustable parameters and indicators for operating status.
Far series outdoor auto circuit recloser
The document provides information on the FAR series pole mounted auto circuit recloser from Zhejiang Farady Electric Co., Ltd. Key details include:
- It uses epoxy resin solid insulation and a long life magnetic actuator, and integrates functions of control, protection, measurement, communication, fault detection and online monitoring.
- It is suitable for overhead distribution lines and substations from 11kV to 38kV. Rated currents range from 200A to 1600A and breaking capacities are from 12.5kA to 31.5kA.
- It has optional communication protocols, measurement functions, reclosing intervals and event recording capabilities.
Far series outdoor auto circuit recloser
The document describes a pole mounted auto circuit recloser manufactured by Zhejiang Farady Electric Co., Ltd. The FAR series recloser can be used on overhead distribution lines and substations from 11kV to 38kV. It integrates control, protection, measurement, communication, fault detection and online monitoring functions. Key features include epoxy resin solid insulation, a magnetic actuator, and recloser functions. It is designed to perform reliably for over 20 years in various environmental conditions.
R501 ADVANCED TRANSFORMER MONITOR | Rugged Monitoring
RUGGED MONITORING’s R501 is the most versatile and advanced multi-channel monitoring solution. Designed to seamlessly integrate into diverse industries, the R501 stands as a testament to our commitment to innovation and reliability in electrical asset monitoring.
Deeter LVCS FP Flameproof Liquid Vertical Continuous Sensor - Spec Sheet
The Deeter LVCS FP is a magnetic float level sensor for measuring liquid levels in potentially explosive environments. It uses a reed switch or Hall effect sensor on a stainless steel probe up to 4 meters in length to provide analog outputs such as 4-20mA or voltage signals. It is ATEX and IECEx approved for gas and dust hazardous areas, has an IP68 rating, and can measure liquid temperatures up to 185°C.
Selecting Radar Level Instruments for Custody Transfer
In many applications, higher-accuracy
measurements are required to protect
the customer from over-billing and the
supplier from under-billing. Common
products requiring this level of accuracy
are typically oils, fuels, edible oils, and
alcohols. In the oil & gas industry, this
requires a system called automatic
tank gauging (ATG) as defined by the
American Petroleum Institute (API)
standards.
Advanced motion controls b15a8
The document describes an analog servo drive that provides 15A of peak current and 7.5A of continuous current. It can interface with digital controllers or operate independently. Key features include adjustable current limits, high switching frequency, fault monitoring, and modes for current control, duty cycle control and velocity control. It is designed to drive brushless DC motors and includes protections against overheating, overcurrent and more.
digital multimeter dt4280-4250-4220 series
This document describes Hioki's DT4200 series of digital multimeters (DMMs). It provides an overview of the various models in the series, their key features and specifications. The series includes high-end, standard and pocket-sized models with different measurement capabilities. Models have fast response times, bright backlights, safety features and memory storage. They are suited for electrical work, laboratories, HVAC and other applications.
Similar to Tank radar set up (20)
RD-FMF12-T Radar level transmitter for rive and lakes
RD-FMF12-T Radar level transmitter for rive and lakes
Varactor diode or varicap diode working and applications
Varactor diode or varicap diode working and applications
Original N-Channel Mosfet IRFD120PBF 120 100V 1.3A DIP-4 New Vishay Siliconix
Original N-Channel Mosfet IRFD120PBF 120 100V 1.3A DIP-4 New Vishay Siliconix
Hydrometry: Field Manual, Field Application of ADCP Volume-4 Part V 2003
Hydrometry: Field Manual, Field Application of ADCP Volume-4 Part V 2003
R501 ADVANCED TRANSFORMER MONITOR | Rugged Monitoring
R501 ADVANCED TRANSFORMER MONITOR | Rugged Monitoring
Deeter LVCS FP Flameproof Liquid Vertical Continuous Sensor - Spec Sheet
Deeter LVCS FP Flameproof Liquid Vertical Continuous Sensor - Spec Sheet
Selecting Radar Level Instruments for Custody Transfer
Selecting Radar Level Instruments for Custody Transfer
More from David Aakre
Limitorque Actuator Set UP.pptx
The document provides instructions for setting the limit switches on a Limitorque valve actuator. It outlines 8 steps for locking out the actuator, manually operating the valve to fully open and closed positions, depressing the setting rod to latch it while the valve rotor engages the limit switch plunger, ensuring the intermediate shaft is secured before moving the valve, and setting both rotors by following the same steps. Safety cautions are provided to lock out power before opening the cover and not operate the valve while the setting rod is depressed.
Trek Communicator.pptx
The document describes how to use the Trex Communicator to easily set up and configure Hart transmitters. It explains that the Trex has a built-in 250 ohm resistor and power supply, allowing it to directly power and communicate with Hart devices. The steps shown include choosing to power the transmitter with the Trex, simulating loop signals, and using the Trex to configure the transmitter's setup and parameters.
How to extract a program from a Redlion.pptx
To extract a program from a Red Lion HMI using Crimson Software, you need a USB cable to connect the HMI to a computer with the matching version of Crimson installed. In the software, select the USB connection under Link, then click Extract to upload the program file from the HMI to your computer where it can be saved. Ethernet IP settings can also be configured by clicking Network to set up a TCP/IP connection to the HMI.
How to extract a program from a Redlion.pptx
To extract a program from a Redlion HMI using Crimson Software, you need a USB cable to connect the HMI to a computer with the matching version of Crimson downloaded. In the software, select the USB connection under Link, then click Extract to upload the program from the HMI to the computer where it can be saved. Ethernet IP settings can also be configured by clicking Network to connect to the HMI over Ethernet.
ROC 800 Serial and Ethernet Connection Setup.pptx
To connect a ROC 800 to a computer via serial port and set up the IP address using ROCKLINK software:
1. Create a DB9 female to RJ45 connector with specific wire configurations and combine it with a RS232 serial converter.
2. Plug the converter into the computer and connect an Ethernet cable to the ROC 800 port.
3. Open the ROCLINK 800 software, directly connect to the ROC, and set the IP address under the device information tabs.
4. The ROC 800 serial port is now connected and its IP address is configured for internet access.
How to Calibrate a BS&W Meter.pptx
To calibrate a BS&W meter:
1. Check the status LED for fault codes such as flashing, which indicate issues like under/over range or needing calibration.
2. Put the meter in calibration mode by pressing both buttons until the LED lights up solid.
3. Connect a volt meter, write down the voltage, and take an oil sample to determine the water cut percentage calibration point.
4. Use the up and down buttons to enter the water cut percentage as the calibration point.
How to manipulate a blender screw speed and
This document provides instructions for correcting sand usage on a frac location by manipulating density meters and blender settings. It explains that sand usage is typically estimated, not exact, and can get out of balance over the course of a job. It then gives various ways to manipulate density meters and blender settings like screw speed to hide using more or less sand than planned in order to get sand usage back on track according to the job chart, including by adjusting calibration points and voltage readings. The goal is to fix imbalances in sand tracking without it being evident on frac charts.
Hourse power math
This document provides instructions for calculating the pumping rate of a frac pump in barrels per minute using simple math. It uses a Weir 4-inch QWS 2500 pump with 5 plungers as an example. The key steps are: (1) calculate the cubic inches of liquid per revolution based on plunger geometry, (2) convert to gallons and then barrels per revolution, (3) factor in the transmission speed ratio to get barrels per transmission revolution, and (4) use the transmission gear ratios and maximum engine speed to calculate the pumping rate in each gear. A chart is provided with the pumping rates for all gears at different engine speeds.
Density meter calibration
This document provides instructions for calibrating a density meter and summarizes procedures for testing density measurement systems using frac slurry mixtures. It outlines a two-point calibration process using air and water, recording calibration results for restoring meter settings, and calibrating on different fluid types. It also describes preparing frac slurry mixtures with various additives to achieve different densities, measuring the true densities of the mixtures, and using the mixtures to calibrate or test a densometer by taking pressure readings and comparing to known densities. The goal is to practice density measurement techniques and calibrate equipment.
Bucket testing on ace blender
1) The document provides steps for conducting a bucket test to calibrate a chemical pump using the ACE software.
2) Key steps include selecting the master flow rate for the bucket test, running the pump in auto at a set point, and comparing the volume in the test bucket to the volume pumped in ACE to check accuracy.
3) If the test is not accurate, the document provides troubleshooting steps like zeroing the micromotion transmitter or performing an auto-tune of the pump settings.
Frac formulas david aakre technologist
This document provides formulas and explanations for calculating frac job parameters such as fluid rates, pressures, horsepower requirements, and blender equations. Key points include:
1. Formulas are given for calculating maximum frac rate, line volume, fluid gradient, bottomhole pressure, frac gradient, horsepower, and pipe time.
2. Modes of monitoring bottomhole pressure during fracturing are described.
3. Equations are outlined for calculating parameters related to blender operations like fluid and proppant volumes and densities.
4. Pump math formulas are defined for calculating fluid volumes per revolution and maximum pump rates based on engine speeds and transmission gear ratios.
5. Steps for bucket testing chemical pumps to validate
Frac formulas david aakre technologist
This document provides formulas and equations for calculating rates, pressures, volumes, densities, and other parameters related to hydraulic fracturing operations. Some key points:
1. Formulas are provided for calculating maximum frac rate, line volume, fluid gradient, bottomhole pressure, frac gradient, horsepower requirements, and other fracturing parameters.
2. Equations are outlined for calculating parameters related to blender operations like clean water weight, sand volumes, slurry volumes, densities, and screw speeds.
3. Pump math formulas define relationships for determining pump capacities based on fluid end geometry, transmission ratios, engine speeds, and other factors.
More from David Aakre (13)
Recently uploaded
一比一原版(uofo毕业证书)美国俄勒冈大学毕业证如何办理
原版一模一样【微信：741003700 】【(uofo毕业证书)美国俄勒冈大学毕业证成绩单】【微信：741003700 】学位证，留信认证（真实可查，永久存档）原件一模一样纸张工艺/offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原。
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问Q/微741003700
【主营项目】
一.毕业证【q微741003700】成绩单、使馆认证、教育部认证、雅思托福成绩单、学生卡等！
二.真实使馆公证(即留学回国人员证明,不成功不收费)
三.真实教育部学历学位认证（教育部存档！教育部留服网站永久可查）
四.办理各国各大学文凭(一对一专业服务,可全程监控跟踪进度)
如果您处于以下几种情况：
◇在校期间，因各种原因未能顺利毕业……拿不到官方毕业证【q/微741003700】
◇面对父母的压力，希望尽快拿到；
◇不清楚认证流程以及材料该如何准备；
◇回国时间很长，忘记办理；
◇回国马上就要找工作，办给用人单位看；
◇企事业单位必须要求办理的
◇需要报考公务员、购买免税车、落转户口
◇申请留学生创业基金
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
办理(uofo毕业证书)美国俄勒冈大学毕业证【微信：741003700 】外观非常简单，由纸质材料制成，上面印有校徽、校名、毕业生姓名、专业等信息。
办理(uofo毕业证书)美国俄勒冈大学毕业证【微信：741003700 】格式相对统一，各专业都有相应的模板。通常包括以下部分：
校徽：象征着学校的荣誉和传承。
校名:学校英文全称
授予学位：本部分将注明获得的具体学位名称。
毕业生姓名：这是最重要的信息之一，标志着该证书是由特定人员获得的。
颁发日期：这是毕业正式生效的时间，也代表着毕业生学业的结束。
其他信息：根据不同的专业和学位，可能会有一些特定的信息或章节。
办理(uofo毕业证书)美国俄勒冈大学毕业证【微信：741003700 】价值很高，需要妥善保管。一般来说，应放置在安全、干燥、防潮的地方，避免长时间暴露在阳光下。如需使用，最好使用复印件而不是原件，以免丢失。
综上所述，办理(uofo毕业证书)美国俄勒冈大学毕业证【微信：741003700 】是证明身份和学历的高价值文件。外观简单庄重，格式统一，包括重要的个人信息和发布日期。对持有人来说，妥善保管是非常重要的。
一比一原版(CalArts毕业证)加利福尼亚艺术学院毕业证如何办理
CalArts毕业证学历书【微信95270640】CalArts毕业证’圣力嘉学院毕业证《Q微信95270640》办理CalArts毕业证√文凭学历制作{CalArts文凭}购买学历学位证书本科硕士,CalArts毕业证学历学位证【实体公司】办毕业证、成绩单、学历认证、学位证、文凭认证、办留信网认证、（网上可查，实体公司，专业可靠）
(诚招代理)办理国外高校毕业证成绩单文凭学位证,真实使馆公证（留学回国人员证明）真实留信网认证国外学历学位认证雅思代考国外学校代申请名校保录开请假条改GPA改成绩ID卡
1.高仿业务:【本科硕士】毕业证,成绩单（GPA修改）,学历认证（教育部认证）,大学Offer,,ID,留信认证,使馆认证,雅思,语言证书等高仿类证书；
2.认证服务: 学历认证（教育部认证）,大使馆认证（回国人员证明）,留信认证（可查有编号证书）,大学保录取,雅思保分成绩单。
3.技术服务：钢印水印烫金激光防伪凹凸版设计印刷激凸温感光标底纹镭射速度快。
办理加利福尼亚艺术学院加利福尼亚艺术学院毕业证文凭证书流程：
1客户提供办理信息：姓名生日专业学位毕业时间等（如信息不确定可以咨询顾问：我们有专业老师帮你查询）；
2开始安排制作毕业证成绩单电子图；
3毕业证成绩单电子版做好以后发送给您确认；
4毕业证成绩单电子版您确认信息无误之后安排制作成品；
5成品做好拍照或者视频给您确认；
6快递给客户（国内顺丰国外DHLUPS等快读邮寄）
-办理真实使馆公证（即留学回国人员证明）
-办理各国各大学文凭（世界名校一对一专业服务,可全程监控跟踪进度）
-全套服务：毕业证成绩单真实使馆公证真实教育部认证。让您回国发展信心十足！
（详情请加一下 文凭顾问+微信:95270640）欢迎咨询！子小伍玩小伍比山娃小一岁虎头虎脑的很霸气父亲让山娃跟小伍去夏令营听课山娃很高兴夏令营就设在附近一所小学山娃发现那所小学比自己的学校更大更美操场上还铺有塑胶跑道呢里面很多小朋友一班一班的快快乐乐原来城里娃都藏这儿来了怪不得平时见不到他们山娃恍然大悟起来吹拉弹唱琴棋书画山娃都不懂却什么都想学山娃怨自己太笨什么都不会斟酌再三山娃终于选定了学美术当听说每月要交元时父亲犹豫了山娃也说爸算了吧咱学校一学期才转
AI-Based Home Security System : Home security
Home security is of paramount importance in today's world, where we rely more on technology, home
security is crucial. Using technology to make homes safer and easier to control from anywhere is
important. Home security is important for the occupant’s safety. In this paper, we came up with a low cost,
AI based model home security system. The system has a user-friendly interface, allowing users to start
model training and face detection with simple keyboard commands. Our goal is to introduce an innovative
home security system using facial recognition technology. Unlike traditional systems, this system trains
and saves images of friends and family members. The system scans this folder to recognize familiar faces
and provides real-time monitoring. If an unfamiliar face is detected, it promptly sends an email alert,
ensuring a proactive response to potential security threats.
Mechanical Engineering on AAI Summer Training Report-003.pdf
Mechanical Engineering PROJECT REPORT ON SUMMER VOCATIONAL TRAINING
AT MBB AIRPORT
Optimizing Gradle Builds - Gradle DPE Tour Berlin 2024
Sinan from the Delivery Hero mobile infrastructure engineering team shares a deep dive into performance acceleration with Gradle build cache optimizations. Sinan shares their journey into solving complex build-cache problems that affect Gradle builds. By understanding the challenges and solutions found in our journey, we aim to demonstrate the possibilities for faster builds. The case study reveals how overlapping outputs and cache misconfigurations led to significant increases in build times, especially as the project scaled up with numerous modules using Paparazzi tests. The journey from diagnosing to defeating cache issues offers invaluable lessons on maintaining cache integrity without sacrificing functionality.
Object Oriented Analysis and Design - OOAD
This ppt gives detailed description of Object Oriented Analysis and design.
Null Bangalore | Pentesters Approach to AWS IAM
#Abstract:
- Learn more about the real-world methods for auditing AWS IAM (Identity and Access Management) as a pentester. So let us proceed with a brief discussion of IAM as well as some typical misconfigurations and their potential exploits in order to reinforce the understanding of IAM security best practices.
- Gain actionable insights into AWS IAM policies and roles, using hands on approach.
#Prerequisites:
- Basic understanding of AWS services and architecture
- Familiarity with cloud security concepts
- Experience using the AWS Management Console or AWS CLI.
- For hands on lab create account on [killercoda.com](https://killercoda.com/cloudsecurity-scenario/)
# Scenario Covered:
- Basics of IAM in AWS
- Implementing IAM Policies with Least Privilege to Manage S3 Bucket
- Objective: Create an S3 bucket with least privilege IAM policy and validate access.
- Steps:
- Create S3 bucket.
- Attach least privilege policy to IAM user.
- Validate access.
- Exploiting IAM PassRole Misconfiguration
-Allows a user to pass a specific IAM role to an AWS service (ec2), typically used for service access delegation. Then exploit PassRole Misconfiguration granting unauthorized access to sensitive resources.
- Objective: Demonstrate how a PassRole misconfiguration can grant unauthorized access.
- Steps:
- Allow user to pass IAM role to EC2.
- Exploit misconfiguration for unauthorized access.
- Access sensitive resources.
- Exploiting IAM AssumeRole Misconfiguration with Overly Permissive Role
- An overly permissive IAM role configuration can lead to privilege escalation by creating a role with administrative privileges and allow a user to assume this role.
- Objective: Show how overly permissive IAM roles can lead to privilege escalation.
- Steps:
- Create role with administrative privileges.
- Allow user to assume the role.
- Perform administrative actions.
- Differentiation between PassRole vs AssumeRole
Try at [killercoda.com](https://killercoda.com/cloudsecurity-scenario/)
Accident detection system project report.pdf
The Rapid growth of technology and infrastructure has made our lives easier. The
advent of technology has also increased the traffic hazards and the road accidents take place
frequently which causes huge loss of life and property because of the poor emergency facilities.
Many lives could have been saved if emergency service could get accident information and
reach in time. Our project will provide an optimum solution to this draw back. A piezo electric
sensor can be used as a crash or rollover detector of the vehicle during and after a crash. With
signals from a piezo electric sensor, a severe accident can be recognized. According to this
project when a vehicle meets with an accident immediately piezo electric sensor will detect the
signal or if a car rolls over. Then with the help of GSM module and GPS module, the location
will be sent to the emergency contact. Then after conforming the location necessary action will
be taken. If the person meets with a small accident or if there is no serious threat to anyone’s
life, then the alert message can be terminated by the driver by a switch provided in order to
avoid wasting the valuable time of the medical rescue team.
一比一原版(USF毕业证)旧金山大学毕业证如何办理
原件一模一样【微信：95270640】【旧金山大学毕业证USF学位证成绩单】【微信：95270640】（留信学历认证永久存档查询）采用学校原版纸张、特殊工艺完全按照原版一比一制作（包括：隐形水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠，文字图案浮雕，激光镭射，紫外荧光，温感，复印防伪）行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备，十五年致力于帮助留学生解决难题，业务范围有加拿大、英国、澳洲、韩国、美国、新加坡，新西兰等学历材料，包您满意。
【业务选择办理准则】
一、工作未确定，回国需先给父母、亲戚朋友看下文凭的情况，办理一份就读学校的毕业证【微信：95270640】文凭即可
二、回国进私企、外企、自己做生意的情况，这些单位是不查询毕业证真伪的，而且国内没有渠道去查询国外文凭的真假，也不需要提供真实教育部认证。鉴于此，办理一份毕业证【微信：95270640】即可
三、进国企，银行，事业单位，考公务员等等，这些单位是必需要提供真实教育部认证的，办理教育部认证所需资料众多且烦琐，所有材料您都必须提供原件，我们凭借丰富的经验，快捷的绿色通道帮您快速整合材料，让您少走弯路。
留信网认证的作用:
1:该专业认证可证明留学生真实身份【微信：95270640】
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
→ 【关于价格问题（保证一手价格）
我们所定的价格是非常合理的，而且我们现在做得单子大多数都是代理和回头客户介绍的所以一般现在有新的单子 我给客户的都是第一手的代理价格，因为我想坦诚对待大家 不想跟大家在价格方面浪费时间
对于老客户或者被老客户介绍过来的朋友，我们都会适当给一些优惠。
选择实体注册公司办理，更放心，更安全！我们的承诺：可来公司面谈，可签订合同，会陪同客户一起到教育部认证窗口递交认证材料，客户在教育部官方认证查询网站查询到认证通过结果后付款，不成功不收费！
办理旧金山大学毕业证毕业证学位证USF学位证【微信：95270640 】外观非常精致，由特殊纸质材料制成，上面印有校徽、校名、毕业生姓名、专业等信息。
办理旧金山大学毕业证USF学位证毕业证学位证【微信：95270640 】格式相对统一，各专业都有相应的模板。通常包括以下部分：
校徽：象征着学校的荣誉和传承。
校名:学校英文全称
授予学位：本部分将注明获得的具体学位名称。
毕业生姓名：这是最重要的信息之一，标志着该证书是由特定人员获得的。
颁发日期：这是毕业正式生效的时间，也代表着毕业生学业的结束。
其他信息：根据不同的专业和学位，可能会有一些特定的信息或章节。
办理旧金山大学毕业证毕业证学位证USF学位证【微信：95270640 】价值很高，需要妥善保管。一般来说，应放置在安全、干燥、防潮的地方，避免长时间暴露在阳光下。如需使用，最好使用复印件而不是原件，以免丢失。
综上所述，办理旧金山大学毕业证毕业证学位证USF学位证【微信：95270640 】是证明身份和学历的高价值文件。外观简单庄重，格式统一，包括重要的个人信息和发布日期。对持有人来说，妥善保管是非常重要的。
Generative AI Use cases applications solutions and implementation.pdf
Generative AI solutions encompass a range of capabilities from content creation to complex problem-solving across industries. Implementing generative AI involves identifying specific business needs, developing tailored AI models using techniques like GANs and VAEs, and integrating these models into existing workflows. Data quality and continuous model refinement are crucial for effective implementation. Businesses must also consider ethical implications and ensure transparency in AI decision-making. Generative AI's implementation aims to enhance efficiency, creativity, and innovation by leveraging autonomous generation and sophisticated learning algorithms to meet diverse business challenges.
https://www.leewayhertz.com/generative-ai-use-cases-and-applications/
Open Channel Flow: fluid flow with a free surface
Open Channel Flow: This topic focuses on fluid flow with a free surface, such as in rivers, canals, and drainage ditches. Key concepts include the classification of flow types (steady vs. unsteady, uniform vs. non-uniform), hydraulic radius, flow resistance, Manning's equation, critical flow conditions, and energy and momentum principles. It also covers flow measurement techniques, gradually varied flow analysis, and the design of open channels. Understanding these principles is vital for effective water resource management and engineering applications.
原版制作(Humboldt毕业证书)柏林大学毕业证学位证一模一样
原件一模一样【微信：bwp0011】《(Humboldt毕业证书)柏林大学毕业证学位证》【微信：bwp0011】学位证，留信认证（真实可查，永久存档）原件一模一样纸张工艺/offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原。
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问微bwp0011
【主营项目】
一.毕业证【微bwp0011】成绩单、使馆认证、教育部认证、雅思托福成绩单、学生卡等！
二.真实使馆公证(即留学回国人员证明,不成功不收费)
三.真实教育部学历学位认证（教育部存档！教育部留服网站永久可查）
四.办理各国各大学文凭(一对一专业服务,可全程监控跟踪进度)
如果您处于以下几种情况：
◇在校期间，因各种原因未能顺利毕业……拿不到官方毕业证【微bwp0011】
◇面对父母的压力，希望尽快拿到；
◇不清楚认证流程以及材料该如何准备；
◇回国时间很长，忘记办理；
◇回国马上就要找工作，办给用人单位看；
◇企事业单位必须要求办理的
◇需要报考公务员、购买免税车、落转户口
◇申请留学生创业基金
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
LLM Fine Tuning with QLoRA Cassandra Lunch 4, presented by Anant
Slides for the 4th Presentation on LLM Fine-Tuning with QLoRA Presented by Anant, featuring DataStax Astra
Software Engineering and Project Management - Software Testing + Agile Method...
Software Testing: A Strategic Approach to Software Testing, Strategic Issues, Test Strategies for Conventional Software, Test Strategies for Object -Oriented Software, Validation Testing, System Testing, The Art of Debugging.
Agile Methodology: Before Agile – Waterfall, Agile Development.
Height and depth gauge linear metrology.pdf
Height gauges may also be used to measure the height of an object by using the underside of the scriber as the datum. The datum may be permanently fixed or the height gauge may have provision to adjust the scale, this is done by sliding the scale vertically along the body of the height gauge by turning a fine feed screw at the top of the gauge; then with the scriber set to the same level as the base, the scale can be matched to it. This adjustment allows different scribers or probes to be used, as well as adjusting for any errors in a damaged or resharpened probe.
Recently uploaded (20)
5G Radio Network Througput Problem Analysis HCIA.pdf
5G Radio Network Througput Problem Analysis HCIA.pdf
SENTIMENT ANALYSIS ON PPT AND Project template_.pptx
SENTIMENT ANALYSIS ON PPT AND Project template_.pptx
2. protection of river banks and bed erosion protection works.ppt
2. protection of river banks and bed erosion protection works.ppt
4. Mosca vol I -Fisica-Tipler-5ta-Edicion-Vol-1.pdf
4. Mosca vol I -Fisica-Tipler-5ta-Edicion-Vol-1.pdf
Mechanical Engineering on AAI Summer Training Report-003.pdf
Mechanical Engineering on AAI Summer Training Report-003.pdf
Optimizing Gradle Builds - Gradle DPE Tour Berlin 2024
Optimizing Gradle Builds - Gradle DPE Tour Berlin 2024
Generative AI Use cases applications solutions and implementation.pdf
Generative AI Use cases applications solutions and implementation.pdf
Zener Diode and its V-I Characteristics and Applications
Zener Diode and its V-I Characteristics and Applications
LLM Fine Tuning with QLoRA Cassandra Lunch 4, presented by Anant
LLM Fine Tuning with QLoRA Cassandra Lunch 4, presented by Anant
Software Engineering and Project Management - Software Testing + Agile Method...
Software Engineering and Project Management - Software Testing + Agile Method...
Tank radar set up
- 1. Tank Radar Set UP David Aakre 1.Connect Hart communicator to Radar 2.Select Basic Set UP. 3.Input measurement: Radar Flange to Tank Bottom. Example: 42’00 5/8 from Tank Tag, = 42.052ft. 4.Input Span: Example 0 ft. = 4maand 40 ft. = 20ma 5.Input Stilling Well Diameter. Example 8 inch = 8/12= .666 ft. 6.Input Tank Geometry Example Round Flat bottom. 7.Input Dielectric 2-4 or Medium for Oil. 8.Input Fluid Properties- Turbulent with Mixer. 9.Hand Gauge Tank level. 10. Offset/ Calibration Input. Use this to match Radar Level with Hand Gauge. Example Radar level is 15 ft. and Hand gauge is 16 ft. Enter in offset 1 ft. to Match. 11. Up-date device and save settings. 12. Cycle Power and Check saved settings
- 2. Radar Master Software Set UP 1.Install a 250 OHM resistor in series In Radar 24V Circuit. The resistor is needed for HART Communications.(DCpower supply 20-24v) 2.Connect Hart Communicator 2 Leads with one on each side of 250 OHM Resistor. Example: Microflex-Microlink USB Hart Modem. 3.Open Radar Master software ( free Down load from Rosemount) 4.Set communications to: HART, Select Enable HART Communications and Port Settings: COM 1 Or Com port number your HART communicator is connected to. Modems select RS 232. Advanced Settings: Baud 1200, Stop bit 1, Parity odd, Preambles 5, Handshake RTS/CTS, Response Time out 1000, Retries 3, Master Mode Secondary. 5.Press Scan To find Instrument 6.Once Connected Run: Wizard to Guided SET UP. Fill in Radar set up information.