Mig welding process is semi automatic when used for manual welding . It can be used in welding automation systems for high quality welds and high productivity.

1. PRINCIPLES OF MIG
WELDING
TECHNOLOGY

2. PRINCIPLE OF MIG WELDING
Gas Metal Arc Welding (GMAW) is commonly referred to as MIG welding (Metal Inert Gas
welding). It is also referred to as MAG welding (Manual Metal Arc Welding). The basic principle of
MIG Welding is, an arc is maintained between the end of the bare wire electrode and the work piece
where the heat source required to melt the parent metal is obtained. The arc melts the end of the
electrode wire, which is transferred to the molten weld pool. For a given wire material and diameter,
the arc current is determined by the wire feed rate. The arc and the weld pool is shielded from the
atmospheric contamination by an externally supplied shield gas. Metal Inert Gas (MIG) welding is a
'flat' arc process (constant) voltage. The required voltage is selected by adjusting the voltage control
knobs provided at the power source. The process itself can be manual, partly mechanized, fully
mechanized or automatic. An example for MIG welding is show below

3. MIG welding Setup MIG welding component
MIG Hard Faced component

4. Schematic representation of MIG welding process:

5. MIG WELDING EQUIPMENT
The basic MIG welding equipment consists of the following components:
• Power source
• Welding Gun
• Gas cylinders with pressure-reducing valve and flow meter
• Wire feeder unit
The basic circuit and the equipment of MIG welding is shown below,

6. Basic MIG Welding Circuit: Fully Automated MIG Welding Equipment:

7. WELDING VARIABLES AND PARAMETERS
1. Electrode extension - affects the amperage. Stick out length should be 10 - 15 mm.
2. Inductance - smoothes the arc characteristic. Also called the choke. If it is Set low it gives excess
penetration and if set high, no penetration.
3. Wire feed speed - amperage. Controls fusion and penetration.
4. Travel speed - controls depth of penetration.
5. Gas flow rate - protects weld from atmosphere.
6. Voltage - set on the welding machine and controls the arc length.
7. Tilt angle - back or fore hand should be not greater than 15° from the perpendicular.
8. The welding position and type of weld are further variables to be considered.

8. METAL TRANSFER ACROSS THE ARC
The weld metal transfer from the electrode to the work is classified into four different types
 Short circuiting transfer
 Globular transfer
 Spray transfer
 Pulsed spray transfer
The mode of weld metal transfer is determined by the following:
 Welding current
 Electrode size
 Electrode composition
 Electrode stick out
 Shielding gas

9. Short circuiting transfer:
Short circuiting transfer uses the lowest welding currents and voltages, which consequently produces very
low heat input. In this mode of welding, the metal is not transferred across the arc gap, but from the electrode
to the work only during a short period when the welding wire is in contact with the weld pool. When the
electrode wire tip touches the weld pool, the arc extinguishes, the voltage goes down and amperage rises. At
this moment, metal is transferred from the melted electrode tip to the weld pool with the help of surface
tension of the melted weld metal.
Globular metal transfer:
Globular metal transfer occurs at relatively low operating currents and voltages but these are still higher than
those used in short circuiting transfer. This metal transfer mode is characterized by a drop, two or three times
larger in diameter than the wire, formed at the tip of the electrode. This droplet is detached from the tip of the
electrode by the effect of a pinch force and the transfer of the droplets in irregular form across the arc is
aided by the effect of the weak electromagnetic and strong gravity forces. As the droplets grow on the tip of
the wire electrode they wobble around and disturb the arc plasma stability. Consequently, the heat-affected
zone in the work becomes narrow, penetration of the weld becomes small, and the weld deposit is irregular
and large amounts of spatter takes place.

10. Spray Transfer:
Under an argon-rich shielding gas, increasing the current and voltage causes a new mode of metal transfer to
appear, the tip of the wire electrode is tapped, the sizes of the droplets become smaller and they are directed
axially in a straight line from the wire to the weld pool. The current level above by which this mode of metal
transfer begins is called transition current. The droplets are much smaller than the diameter of the wire and
they detach with pinch force much more rapidly than with the globular transfer mode, there is very little
spatter and the surface of the weld bead is smooth.
Pulsed spray transfer:
The Pulsed mode of metal transfer in MIG is used for applications where a good penetration and reduced
heat input are required. A pulsed current transfer is a spray type of transfer that occurs at regularly spaced
intervals instead of constantly. This mode of metal transfer can only be produced if the power source is able
to supply a pulsed current. The level of a welding current supplied by a pulsing type of power source varies
between high and low levels. Whereas high level is above the transition current and produces the droplets,
low level or background current has only sufficient energy to sustain the arc.

11. WELDING TORCH
 The Welding torch feeds the wire and directs inert gas to the weld area with the help of gas nozzle. They
are highly insulated as electric current is flowing in order to ensure operator safety.
 The selection of the proper MIG torch, commonly called a MIG gun, depends upon the following factors:
o Type of welding: semiautomatic, hard automation or robotic automation.
o Level of current (amps) required by the welding application and capacity of the torch.
o Shielding gas selected.
o Duty cycle of the torch.
o Preference of an air-cooled or water-cooled torch.

12.  Both air cooled (natural) and water cooled (when the current is above 200 amp) torches are available. The
basic welding torch consist of
o Gas Nozzle
o Copper contact tube
o Water hose (if water cooled)
o Gas hose
o Welding cable
o Wire conduit
o Trigger switch
 The duty cycle of the MIG torch selected relates to the shielding gas and the maximum current that is
specific to the welding application.

13. SCHEMATIC REPRESENTATION OF WELD TORCH:

14. WELDING TORCH

15. POWER SOURCE
Only Direct Current DC (Reverse Polarity - DCRP) source is used for MIG welding process. A power source
with a flat characteristic is almost used for Metal Inert Gas Welding process as it offers several advantages
e.g., latitude in setting the welding condition and self-regulated arc besides it also meets the special
requirements of dip transfer welding. Power sources incorporate output characteristics designed to optimize
the arc performance for a given welding process. For MIG, the output characteristics fall into two main
categories:
1. constant current
2. constant voltage
The important advantage of flat characteristic power source is its ability to produce self-regulated arc. Self-
regulated arc means maintaining the arc length constant. With a constant potential power source, change in
arc voltage will have marked effects on current. Thus if the arc length is reduced from the set value, there
will be an increase in current resulting in faster burn off rate and the arc length will be adjusted back to its
original value.

16. In other hand increase in arc length from a set value would increase the arc voltage resulting in less current
and a low burn off rate. The arc length would be restored to the original length. Self-adjustment will operate
successfully only when the change in current produced by voltage fluctuations is sufficiently large to
produce a large alteration in burn off, and rapid response rate and correction that the disturbance cannot beat.
Current density is defined as the current employed with a particular electrode diameter divided by its current
carrying cross-sectional area. If the wire feed speed is low, then the current density will be low, and vice
versa. Lower current density applied to a given electrode is associated with the short-circuit mode of metal
transfer. Higher current density is associated with the higher energy modes of metal transfer: globular, axial
spray transfer or the more advanced pulsed spray metal transfer.

17. SHIELDING GASES
The primary purpose of shielding gas is to protect the molten weld metal from contamination by the
oxygen and nitrogen in air. The type of shielding gas used has a major influence on the weld quality.
Only inert gases and their mixtures are utilized for welding. The required purity of the gases must be
guaranteed.
• MAG welding + Reactive shielding gasses (oxygen, nitrogen, carbon dioxide &
hydrogen)
• MIG welding + Inert shielding gasses (Argon & Helium)
Although pure inert gas protects metal at any temperature from reaction with constituents of air, they
are not suitable for all welding applications. Controlled quantity of reactive gas mixes with inert gas
improves the arc action and metal transfer characteristics when welding the steel, but such mixtures are
not used for the reactive metals. The heavier a gas, the more effective it is for gas shielding. Helium is
very light, argon is about 10 times heavier than helium and about 30% heavier than air.

18. The reactive gas are not generally used alone for arc shielding, carbon dioxide can be used alone or
mixed with an inert gas for welding many carbon and low alloy steels. Oxygen is used in small
quantity with one of the inert gasses – usually Argon. Nitrogen is used occasionally but is mixed
with argon, as a shielding gas to weld copper. The most extensive use of nitrogen is in Europe,
where helium is relatively unavailable.
PENETRATION PATTERN FOR VARIOUS SHIELDING GASSES:

19. ADVANTAGES
• Ability to provide high quality welds, for a wide range of ferrous and non-ferrous alloys, at a low cost.
• The ability to join a wide range of material types and thicknesses.
• Simple equipment components are readily available and affordable.
• MIG welding has higher electrode efficiencies (93% - 98%).
• All-position welding’s are possible.
• Excellent weld bead appearance.
• Low hydrogen weld deposit
• Low heat input when compared to other welding processes.
• Less weld spatter and slag makes weld clean up fast and easy.
• Less welding fumes when compared to SMAW (Shielded Metal Arc Welding) and FCAW (Flux-Cored
Arc Welding) processes.

20. DEFECTS AND CAUSES
• Lack of fusion.
• Excessive penetration.
• Silica inclusions (with steel only).
• Solidification (center line) cracking: Spray transfer current too high, deep narrow prep.
• Porosity: Gas flow too high or too low, blocked nozzle, leaking gas line, draughty conditions, nozzle to
work distance too long, Painted, primed, wet or oily work surface, damp or rusty wire.
• Lack of penetration: Current too low, prep to narrow, root face too thick, root gap too small, worn tip
causing irregular arcing, irregular wire feed, poor technique, mismatched joint.
• Undercut: Speed too high, current too high, irregular surface, wrong torch angle.
• Crater cracking: Poor finishing technique.
• Spatter: Inadequate choke, voltage too low, rusty or primed plate.

21. LIMITATIONS
 The lower heat input characteristic of the short-circuiting mode of metal transfer restricts its use to thin
materials.
 The higher heat input axial spray transfer generally restricts its use to thicker base materials.
 The higher heat input mode of axial spray is restricted to flat or horizontal welding positions.
 The use of argon based shielding gas for axial spray and pulsed spray transfer modes is more expensive
than 100% carbon dioxide (CO2).

22. APPLICATIONS
It is used in:
• Structural steel.
• Aluminum sections.
• Stainless steel and nickel alloys.
• Some offshore applications (flux core only).

23. Arcraft Plasma Equipments (I) Pvt Ltd.,
124, Diamond Industrial Estate,
Ketkipada, Dahisar (East),
Mumbai- 400068.
INDIA.
Ph : 00-91-22-28965890, 28965745, 28963247
Fax: 00-91-22-28966418