Effect of Stitch Length on Different Properties of Plain Single Jersey FabricIJMERJOURNAL
ABSTRACT: The works reported in this paper present the effects of stitch length on different properties of plain single jersey fabric. Fabric properties can be changed due to use of various counts of yarn, type (ring, rotor, and compact), quality, stitch length, structural geometry, fiber composition, etc. With an increase in stitch length, the properties like Courses Per Inch (CPI), Wales Per Inch (WPI), GSM and stitch density will be decreased when the remaining other parameters are constant. Again shrinkage and spirality will be increased and bursting strength decreased with the increased stitch length. Pilling and abrasion resistance show lower grading when stitch length increases.
An Investigation on Different Physical Properties of Cotton Woven Fabrics IJERA Editor
In this study, “An Investigation on Different Physical Properties of Cotton Woven Fabrics”, some sample fabrics were produced with plain, 2/2 twill, 3/1 twill and 4-end satin weave structure using four different weft counts. By means of regression, the correlation coefficient and correlation between different properties of fabrics were investigated. The findings of this study revealed that the crease recovery angle and the bending length are inversely proportional to each other. It was also found that with the increasing of weft yarn counts lead to a decreasing in stiffness, abrasion resistance and increasing in crease recovery angle. The pilling and wrinkle recovery affected very low by the increase of weft yarn count and for the variation of weave structure. Plain weave was superior to other structures in stiffness where as twill weave showed higher crease recovery.
Comparison of some of Denim Fabric Properties produced with different Weftijsrd.com
The aim of this study was to asses and compares the some of denim fabric properties using three different weft yarns. Threads per inch and weft type are some of the most important parameters that affect both weaving performance and fabric property. Experimental studies were conducted by weaving fabrics with same warp yarn i.e. 9'OE Rotor yarn. Three different weft yarns are (1) Excel (2) Cotton (3) Polyester. These all are same count. Denim fabrics was woven in three different twill weave (1) 2/1 (2) 3/1 (3) 2/2. It was found the weave type and weft type affects fabric properties. The weave and weft yarn has great impact on the some of comfort related properties also i.e. air permeability, tensile strength, tear strength, and seam slippage, bursting strength.
fiber strength and fiber fineness are described in detail about the machinery and discussed about new computerized testing machines which are used to determine the strength and fineness of the fiber.
Effect of Stitch Length on Different Properties of Plain Single Jersey FabricIJMERJOURNAL
ABSTRACT: The works reported in this paper present the effects of stitch length on different properties of plain single jersey fabric. Fabric properties can be changed due to use of various counts of yarn, type (ring, rotor, and compact), quality, stitch length, structural geometry, fiber composition, etc. With an increase in stitch length, the properties like Courses Per Inch (CPI), Wales Per Inch (WPI), GSM and stitch density will be decreased when the remaining other parameters are constant. Again shrinkage and spirality will be increased and bursting strength decreased with the increased stitch length. Pilling and abrasion resistance show lower grading when stitch length increases.
An Investigation on Different Physical Properties of Cotton Woven Fabrics IJERA Editor
In this study, “An Investigation on Different Physical Properties of Cotton Woven Fabrics”, some sample fabrics were produced with plain, 2/2 twill, 3/1 twill and 4-end satin weave structure using four different weft counts. By means of regression, the correlation coefficient and correlation between different properties of fabrics were investigated. The findings of this study revealed that the crease recovery angle and the bending length are inversely proportional to each other. It was also found that with the increasing of weft yarn counts lead to a decreasing in stiffness, abrasion resistance and increasing in crease recovery angle. The pilling and wrinkle recovery affected very low by the increase of weft yarn count and for the variation of weave structure. Plain weave was superior to other structures in stiffness where as twill weave showed higher crease recovery.
Comparison of some of Denim Fabric Properties produced with different Weftijsrd.com
The aim of this study was to asses and compares the some of denim fabric properties using three different weft yarns. Threads per inch and weft type are some of the most important parameters that affect both weaving performance and fabric property. Experimental studies were conducted by weaving fabrics with same warp yarn i.e. 9'OE Rotor yarn. Three different weft yarns are (1) Excel (2) Cotton (3) Polyester. These all are same count. Denim fabrics was woven in three different twill weave (1) 2/1 (2) 3/1 (3) 2/2. It was found the weave type and weft type affects fabric properties. The weave and weft yarn has great impact on the some of comfort related properties also i.e. air permeability, tensile strength, tear strength, and seam slippage, bursting strength.
fiber strength and fiber fineness are described in detail about the machinery and discussed about new computerized testing machines which are used to determine the strength and fineness of the fiber.
Evaluation of physico mechanical properties of 1×1 interlock cotton knitted f...Elias Khalil (ইলিয়াস খলিল)
The Physico-Mechanical properties of knitted fabric can be changed due to use of various count of yarn, type of yarn (ring, rotor, and compact), quality of yarn, Loop length / Stitch length, structural geometry, fibre composition of yarn etc. This study focused on the various Loop length effect of grey interlock knit structure. With an increase in Loop length, the dimensional properties like CPI, WPI, GSM, thickness & tightness factor will be decreased; while comfort properties like air permeability & water absorbency will be increased. Again shrinkage & spirality will be decreased with increased Loop length at grey stage. Other properties such as bursting strength, abrasion resistance & pilling resistance improved with increased Loop length. Though all the tests for fabric properties were carried out for grey stage, there properties can considerably vary after further finishing of the fabrics. As finishing is mandatory for fabric production, so now-a-days, these kinds of tests are carried out after finishing stage & proper controlling is done according desired quality. Sometimes, controlling of some properties of finished fabrics are beyond our trial. In that case, analysis of fabric properties at grey stage can help us to take various control & corrective actions when necessary.
Hairiness is characterized by the quantity of freely moving fibre ends or fibre loops projecting from a yarn or textile fabric (woven, knitted or non woven fabrics).
In term of measurement Hairiness corresponds to the total length of the protruding fibres in unit length of one centimeter.
The Effect of Twist Multiplier, Elastane Percentage and Pick Density on Denim...CrimsonpublishersTTEFT
The Effect of Twist Multiplier, Elastane Percentage and Pick Density on Denim Quality by A K Choudhary in Trends in Textile Engineering & Fashion Technology
For an end consumer of denim garments, the most important factors are performance and comfort after few aesthetic factors such as appearance and fashion appeal. For stretchable denim fabric, the fit related comfort lies in ability of the fabric to be stretched and recover when a repeated load is applied due to body movements without any permanent set called bagging. In this study, the interactive effect of twist multiplier of weft yarn, denier elastane fibre and fabric areal density on performance of denim fabric was investigated. The denier of elastane fibre used with weft yarn of three different twist multiplier- 4.9, 5.2 and 5.5, is changed as 40D, 55D and 70D. The areal density of fabric is changed through change in picks per inch as 50, 55 and 60. Performance was analysed on the basis of results of breaking strength, breaking elongation and cyclic loading stretch properties. The test results revealed that the tensile strength and breaking elongation properties of denim fabric, for both before and after cyclic loading are in the same trend, but after cyclic loading due to fatigue behaviour, tensile strength and breaking elongation was reduced. The breaking elongation increased as lycra content increases in the fabric and with increase in lycra content percentage, tensile strength was decreased slightly.
Influence of Gas Yarn Singeing On Viscose Spun Yarn Characteristicsiosrjce
Viscose spun yarnhas more hairiness and poses problem in the subsequent processes like yarn dyeing,
fabric production and fabric processing due to protruding of hairs. In this research work, an attempt has been
made to singe the viscose spun yarns of most commonly used yarn counts. Its influence on yarn quality
characteristics were compared and studied with its parent un-singed yarns. It has been found that the primary
objective of hairiness reduction was well achieved with singeing processes; however there isan impact on other
quality characteristics such as yarn imperfections, tenacity and yarn elongation. There is overall improvement
in yarn imperfection results by singeing process. Yarn tenacity is also improved after singeing, but there is drop
in yarn elongation due to singeing.
High Volume Instrument in QC Department of Textile IndustryMohiuddin Chowdhury
The testing of fibers was always of importance to the spinner. It is done by the HVI machine. High volume instrument systems are based on the fiber bundle strength testing, ie, many fibers are checked at the same time and their average values determined. Traditional testing using micronaire, pressley, stelometre, and fibrous graph are designed to determine average value for a large number of fibers, the so called fibre bundle tests. In HVI, the bundle testing method is automated. Here, the time for testing is less and so the number of samples that could be processed is increased, quite considerably. The influence of operator is reduced.
The contents are written in a way that the student understands the basics tests that are done to evaluate the textile fibers. In specific the properties namely length, strength, maturity and elongation.
Effect of stitch length on physical and mechanical properties of single jerse...Elias Khalil (ইলিয়াস খলিল)
The physical and mechanical properties of knitted fabric can be changed due to use of various count of yarn, type of yarn
(ring, rotor, and compact), quality of yarn, stitch length / loop length, structural geometry, fiber composition of yarn etc. This study
focused on the various stitch length effect of grey single jersey. With an increase in stitch length, the dimensional properties like CPI,
WPI, GSM, thickness & tightness factor will be decreased for all the structures; while comfort properties like air permeability & water
absorbency will be increased. Again shrinkage & spirality will be decreased with increased stitch length at grey stage. Other properties
such as bursting strength, abrasion resistance & pilling resistance improved with increased stitch length. Though all the tests for fabric
properties were carried out for grey stage, there properties can considerably vary after further finishing of the fabrics. As finishing is
mandatory for fabric production, so now-a-days, these kinds of tests are carried out after finishing stage & proper controlling is done
according to desired quality. Sometimes, controlling of some properties of finished fabrics are beyond our trial. In that case, analysis of
fabric properties at grey stage can help us to take various control & corrective actions when necessary.
International Journal of Engineering Research and DevelopmentIJERD Editor
Electrical, Electronics and Computer Engineering,
Information Engineering and Technology,
Mechanical, Industrial and Manufacturing Engineering,
Automation and Mechatronics Engineering,
Material and Chemical Engineering,
Civil and Architecture Engineering,
Biotechnology and Bio Engineering,
Environmental Engineering,
Petroleum and Mining Engineering,
Marine and Agriculture engineering,
Aerospace Engineering.
Evaluation of physico mechanical properties of 1×1 interlock cotton knitted f...Elias Khalil (ইলিয়াস খলিল)
The Physico-Mechanical properties of knitted fabric can be changed due to use of various count of yarn, type of yarn (ring, rotor, and compact), quality of yarn, Loop length / Stitch length, structural geometry, fibre composition of yarn etc. This study focused on the various Loop length effect of grey interlock knit structure. With an increase in Loop length, the dimensional properties like CPI, WPI, GSM, thickness & tightness factor will be decreased; while comfort properties like air permeability & water absorbency will be increased. Again shrinkage & spirality will be decreased with increased Loop length at grey stage. Other properties such as bursting strength, abrasion resistance & pilling resistance improved with increased Loop length. Though all the tests for fabric properties were carried out for grey stage, there properties can considerably vary after further finishing of the fabrics. As finishing is mandatory for fabric production, so now-a-days, these kinds of tests are carried out after finishing stage & proper controlling is done according desired quality. Sometimes, controlling of some properties of finished fabrics are beyond our trial. In that case, analysis of fabric properties at grey stage can help us to take various control & corrective actions when necessary.
Hairiness is characterized by the quantity of freely moving fibre ends or fibre loops projecting from a yarn or textile fabric (woven, knitted or non woven fabrics).
In term of measurement Hairiness corresponds to the total length of the protruding fibres in unit length of one centimeter.
The Effect of Twist Multiplier, Elastane Percentage and Pick Density on Denim...CrimsonpublishersTTEFT
The Effect of Twist Multiplier, Elastane Percentage and Pick Density on Denim Quality by A K Choudhary in Trends in Textile Engineering & Fashion Technology
For an end consumer of denim garments, the most important factors are performance and comfort after few aesthetic factors such as appearance and fashion appeal. For stretchable denim fabric, the fit related comfort lies in ability of the fabric to be stretched and recover when a repeated load is applied due to body movements without any permanent set called bagging. In this study, the interactive effect of twist multiplier of weft yarn, denier elastane fibre and fabric areal density on performance of denim fabric was investigated. The denier of elastane fibre used with weft yarn of three different twist multiplier- 4.9, 5.2 and 5.5, is changed as 40D, 55D and 70D. The areal density of fabric is changed through change in picks per inch as 50, 55 and 60. Performance was analysed on the basis of results of breaking strength, breaking elongation and cyclic loading stretch properties. The test results revealed that the tensile strength and breaking elongation properties of denim fabric, for both before and after cyclic loading are in the same trend, but after cyclic loading due to fatigue behaviour, tensile strength and breaking elongation was reduced. The breaking elongation increased as lycra content increases in the fabric and with increase in lycra content percentage, tensile strength was decreased slightly.
Influence of Gas Yarn Singeing On Viscose Spun Yarn Characteristicsiosrjce
Viscose spun yarnhas more hairiness and poses problem in the subsequent processes like yarn dyeing,
fabric production and fabric processing due to protruding of hairs. In this research work, an attempt has been
made to singe the viscose spun yarns of most commonly used yarn counts. Its influence on yarn quality
characteristics were compared and studied with its parent un-singed yarns. It has been found that the primary
objective of hairiness reduction was well achieved with singeing processes; however there isan impact on other
quality characteristics such as yarn imperfections, tenacity and yarn elongation. There is overall improvement
in yarn imperfection results by singeing process. Yarn tenacity is also improved after singeing, but there is drop
in yarn elongation due to singeing.
High Volume Instrument in QC Department of Textile IndustryMohiuddin Chowdhury
The testing of fibers was always of importance to the spinner. It is done by the HVI machine. High volume instrument systems are based on the fiber bundle strength testing, ie, many fibers are checked at the same time and their average values determined. Traditional testing using micronaire, pressley, stelometre, and fibrous graph are designed to determine average value for a large number of fibers, the so called fibre bundle tests. In HVI, the bundle testing method is automated. Here, the time for testing is less and so the number of samples that could be processed is increased, quite considerably. The influence of operator is reduced.
The contents are written in a way that the student understands the basics tests that are done to evaluate the textile fibers. In specific the properties namely length, strength, maturity and elongation.
Effect of stitch length on physical and mechanical properties of single jerse...Elias Khalil (ইলিয়াস খলিল)
The physical and mechanical properties of knitted fabric can be changed due to use of various count of yarn, type of yarn
(ring, rotor, and compact), quality of yarn, stitch length / loop length, structural geometry, fiber composition of yarn etc. This study
focused on the various stitch length effect of grey single jersey. With an increase in stitch length, the dimensional properties like CPI,
WPI, GSM, thickness & tightness factor will be decreased for all the structures; while comfort properties like air permeability & water
absorbency will be increased. Again shrinkage & spirality will be decreased with increased stitch length at grey stage. Other properties
such as bursting strength, abrasion resistance & pilling resistance improved with increased stitch length. Though all the tests for fabric
properties were carried out for grey stage, there properties can considerably vary after further finishing of the fabrics. As finishing is
mandatory for fabric production, so now-a-days, these kinds of tests are carried out after finishing stage & proper controlling is done
according to desired quality. Sometimes, controlling of some properties of finished fabrics are beyond our trial. In that case, analysis of
fabric properties at grey stage can help us to take various control & corrective actions when necessary.
International Journal of Engineering Research and DevelopmentIJERD Editor
Electrical, Electronics and Computer Engineering,
Information Engineering and Technology,
Mechanical, Industrial and Manufacturing Engineering,
Automation and Mechatronics Engineering,
Material and Chemical Engineering,
Civil and Architecture Engineering,
Biotechnology and Bio Engineering,
Environmental Engineering,
Petroleum and Mining Engineering,
Marine and Agriculture engineering,
Aerospace Engineering.
Effect of count and stitch length on spirality of single jersey knit fabriceSAT Journals
Abstract
The following paper focuses on change in spirality due to stitch length and count variation .This work was carried out with 12 samples of single jersey knit fabrics which were scoured and bleached with NaOH and H2O2 (35% strength), dyed with reactive dye (Remazol Yellow RR reactive class) and were finished as standard procedure . After finishing the samples were tested for spirality and compared between different stitch length and count. The result obtained in this research indicated that spirality increases strongly due to increase of stitch length when count of yarn is fixed and on fixed stitch length spirality increases with the increment of count.
Keywords: Spirality, Count, Stitch length.
Handle of cotton: wool knitted khadi fabriciosrjce
Hand of cotton: woolhand knitted fabrics has been reported in this study. Indian crossbred wool
(Rambouillet and Chokla) was blended with cotton (Mech I) in three different ratios (10-90%, 20-80% and 30-
70%) and yarns were prepared on hand spinning system.Knitted fabric samples were constructed on 10-12
gauge, flat bed hand knitting machine. Fabric handle was objectively assessed by SiroFAST.
Investigation on the Changes of Areal Density of Knit Fabric with Stitch Leng...iosrjce
Stitch length and GSM (gram per square meter) are the two major parameters for making a knit
fabric. The relationship between stitch length (S.L) and GSM is inversely proportional if the other parameter
remain constant. Again the presence of tuck loop in knit fabric structure make the fabric heavier than the plain
single jersey fabric having all knit loop because of the accumulation of yarn in the tucking place. In this study,
an experimental work was offered to understand the influence of different stitch length on the GSM of knit fabric
with respect to the change of tuck loop percentage in the knit fabric structure. Here three fabric (single jersey,
single lacoste and polo pique) having different tuck loops percentage with five different stitch lengths were
selected where the other parameters were constant. With the increment of tuck loop percentage and descending
of stitch length, a measurable increase in areal density was observed, where the GSM increment percentage was
maximum at 2.70 mm stitch length for every tuck loop percentage. After that the gradual reduction of stitch
length resulted in the lower rate of GSM increment.
International Journal of Engineering Research and Development (IJERD)IJERD Editor
journal publishing, how to publish research paper, Call For research paper, international journal, publishing a paper, IJERD, journal of science and technology, how to get a research paper published, publishing a paper, publishing of journal, publishing of research paper, reserach and review articles, IJERD Journal, How to publish your research paper, publish research paper, open access engineering journal, Engineering journal, Mathemetics journal, Physics journal, Chemistry journal, Computer Engineering, Computer Science journal, how to submit your paper, peer reviw journal, indexed journal, reserach and review articles, engineering journal, www.ijerd.com, research journals,
yahoo journals, bing journals, International Journal of Engineering Research and Development, google journals, hard copy of journal
Effect of different types of washing processes on the strength and weight los...Hafeezullah Memon
Denim fabric is preferred not only for casual use in the garments, but now even some use it formally in daily routine garments. These denim garments passes through the washing and finishing process. These washing include, bleach wash, enzyme wash and stone wash. The chemical washes are normally used to remove unfixed dyes and other particulate from the surface of fabric [1]. Whereas enzyme wash is used to obtain different looks into the garments. The denim garments being used today are liked with worn look, this worn look is obtained by the rigorous washing. These introductions of the worn looks by rigorous washing lead to the loss of strength of the garments[2]. It is obvious that there will be some loss in terms of the strength of the garments, but till what extent the loss in strength comes into the garments is here to be determined. This project is industrial based project, in which Tensile strength, Tear strength and weight loss (GSM) of garments by using different washing methods being practiced.
Graphene is a material that attracts attention in technical textile applications as in many other areas due to its outstanding features. In this study, it was aimed to investigate the performance properties of graphene coated fabrics. Pre-treated polyester fabrics were coated with nano-graphene powders at different concentration rates (50, 100 and 200 g/kg) by knife-over-roll technique. According to test results, generally, the graphene coating had a positive effect on the performance properties of polyester fabrics.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
Hierarchical Digital Twin of a Naval Power SystemKerry Sado
A hierarchical digital twin of a Naval DC power system has been developed and experimentally verified. Similar to other state-of-the-art digital twins, this technology creates a digital replica of the physical system executed in real-time or faster, which can modify hardware controls. However, its advantage stems from distributing computational efforts by utilizing a hierarchical structure composed of lower-level digital twin blocks and a higher-level system digital twin. Each digital twin block is associated with a physical subsystem of the hardware and communicates with a singular system digital twin, which creates a system-level response. By extracting information from each level of the hierarchy, power system controls of the hardware were reconfigured autonomously. This hierarchical digital twin development offers several advantages over other digital twins, particularly in the field of naval power systems. The hierarchical structure allows for greater computational efficiency and scalability while the ability to autonomously reconfigure hardware controls offers increased flexibility and responsiveness. The hierarchical decomposition and models utilized were well aligned with the physical twin, as indicated by the maximum deviations between the developed digital twin hierarchy and the hardware.
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.