Here is the list of major electrical and electronic components utilized in electrical and electronic projects and several circuits are designed with numerous components like Resistors, Capacitors, Fuses, Transistors, Integrated Circuits, Relays, Switches, Motors, Circuit Breakers, Resistors, Inductors, Transformers, Battery And Fuse.
What is electronics?
Electronics is the science of how to control electric energy, which the electrons have a fundamental role.
This presentation gives a brief explanation about what is electronics and each of the part of the electronic components.
What is electronics?
Electronics is the science of how to control electric energy, which the electrons have a fundamental role.
This presentation gives a brief explanation about what is electronics and each of the part of the electronic components.
The basics of electronics can be watched through the link http://bit.ly/2PPv0mv
A Diode is a semiconductor device with two terminals, typically allowing the flow of current in one direction only.
a thermionic valve having two electrodes (an anode and a cathode).
This presentation is for beginners of electronics. This will give you a brief about all the important basic building blocks of electronics and hence will be helpful in creating a good foundation.
The full basics of Electrical Components can be seen in the link http://bit.ly/2PIOIQM
A switch in an electronic device is used to interrupt the flow of electricity or electric current. Electrical switches are binary devices, they can be either completely off or completely on. In simple English, a switch is an electronic device that is used to break or make the electronic circuit.
The basics of electronics can be watched through the link http://bit.ly/2PPv0mv
A Diode is a semiconductor device with two terminals, typically allowing the flow of current in one direction only.
a thermionic valve having two electrodes (an anode and a cathode).
This presentation is for beginners of electronics. This will give you a brief about all the important basic building blocks of electronics and hence will be helpful in creating a good foundation.
The full basics of Electrical Components can be seen in the link http://bit.ly/2PIOIQM
A switch in an electronic device is used to interrupt the flow of electricity or electric current. Electrical switches are binary devices, they can be either completely off or completely on. In simple English, a switch is an electronic device that is used to break or make the electronic circuit.
Discover affordable electronic components at Express-Technology Group. We offer high-quality parts at competitive prices, ensuring reliable performance without breaking the bank. Shop our extensive inventory for budget-friendly solutions to meet all your electronic project needs.
“Microcontroller Based Substation Monitoring system with gsm modem”.Priya Rachakonda
• The system is used for transmitting the message to predefined number about the
status of electrical parameters such as voltage, current, temperature etc., to improve
the quality of power.
• Studied about the protection, monitoring and control of a power system.
Get The Best Quality Components For Your Needs From The Top Electronic Compon...expess-technology
You can find all types of electrical components for industrial, commercial, and residential applications uses from the top electronic components' distributors like Express Technology Group. Some of the most frequently ordered products from the top electronic components' distributors are
Current Electricity Chp-8 General Science 9th 10thKamran Abdullah
Subject : General Science
Teacher: Mr Ehtisham Ul Haq
Class: BS EDUCATION
Semester: 2nd (Spring(2023-2027)
Date Of Starting Of Semester : 4 September 2023
Date Of End Of Semester : 20 January 2024
University Of Sargodha
Institute of Education
These are the presentation slides that we prepare by our own research and work!
Purchase The Highest-quality Components For Your Requirements From The Leadin...expess-technology
Top electronic components distributors, such as Express Technology Group, offer a wide variety of electrical components for usage in commercial, residential, and industrial settings. Among the most popular items that leading distributors of electrical components order are
basic electrical and electronics engg. components of LT switch gear, switch fuse unit, MCB, MCCB, ELCB, TYPES OF WIRES AND CABLES, ELECTRICAL EARTHING, TYPES OF BATTERIES,
SCADA for remote industrial plant project is used to process the real time data acquisition under supervisory control for large scale remote industries.
TV Remote Jammer | 555 Timer Projects | Final Year Engineering ProjectsEdgefxkits & Solutions
This project is a simple but effective TV remote jammer that distracts the ir receiver in tv by using 555 timer. Rays are emitted by standard 38KHz Tv remote.
This predefined speed control of BLDC motor runs a motor at user desired speed by using EEPROM for storing speed. It is an effective speed control method.
How to select the diy electrical projects kit by engineering studentsEdgefxkits & Solutions
The DIY Electrical Projects kit is an interesting assortment of all the nuts,bolts and accessories required to assemble the electrical equipments. This kit helps the students to gain the practical experience of real life electrical assignments on the job.
This article discusses about how to build a robot vehicle with arduino, AVR, robot body, DC motor, 8051 microcontroller, metal detector and motor driver IC.
This article tells about what is an Opto electronic oscillator, working of the oscillator, multi-loop Opto-electronic oscillator, and its applications.
Engineering students should give more importance to mini projects which is designed by students to learn its practical applications using Do It Yourself Kit.
This is used to track the exact location of a vehicle using GPS tracking systems and give information about the position to concerned person through GSM via SMS.
Project is used to control traffic signal system automatically with IR sensors. Signal timing changes automatically on sensing the traffic density at junctions.
This article discusses what is an electronic speed control, ESC circuit, components used in electronic speed control, features, types and its applications
Prepaid energy meter using GSM is used to record consumed units and send an alert to user via GSM. It is used to reduce power theft in commercial areas.
This project is used to control electrical appliances or loads through a personal computer (PC) like theatre lighting can be centrally controlled from a PC.
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
2. http://www.edgefxkits.com/
Introduction
Electrical and Electronic Components
Used in Projects
There are numerous basic electrical and electronic components
are normally found in numerous circuits of peripherals like hard
disks, mother boards, etc. Several circuits are designed with
numerous components like resistors, capacitors, inductors,
transistors, transformers, switches and fuses etc.
3. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
The Major Electrical and Electronic Components Are
Resistors, Capacitors, Fuses, Transistors, Integrated Circuits,
Relays, Switches, Motors, Circuit Breakers, Resistors, Inductors,
Transformers, Battery, And Fuse.
The major electrical and electronic components utilized in electrical
and electronic projects are.
4. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
About Active and Passive Components
1. Active components
A component that provides and controls energy.
2. Passive Components
A component that responds to the flow of voltage and either
dissipates or store energy.
6. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Resisto
r
The electrical device may also be used to afford a particular voltage to a
semiconductor.
Once current flows through the resistor.
The resistor absorbs the voltage and degenerates within the form of
heat.
Resistors might have variable or mounted resistances.
7. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Resisto
r
The current flow through a resistor is directly proportional to the
voltage across the resistor terminals.
The relationship is pictured by Ohm’s law.
Ohms law V=IR from this equation, we are able to get I=V/R
Where, ‘V’ is that the voltage of the conductor, ‘I’ is the current
through the conductor.
‘R’ is the resistance of the conductor.
8. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Capacitor
A capacitor is a two terminal linear passive component that is made from 2
conductive plates with an insulator between them.
9. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Capacitor
The main function of a capacitor is that, it stores voltage once an
electrical charge is forced onto its terminals from a power supply.
It maintains the charge even when getting disconnected from the
power supply.
A capacitor is employed with a resistor and can also be used as a
filter to permit the AC signals and block the DC signals.
10. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Capacitor
The stored electrical charge is Q=CV
Where, “C” is the capacitive reactance and ‘V’ is the applied voltage.
Thus, the current flow through a capacitor is I= C dv/dt
11. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Microcontroller
A microcontroller is a small computer on
a single integrated circuit.
It assembles all the options which are
found within the microprocessor.
it has a high concentration of on chip amenities like RAM, ROM, timers I/O
ports, serial port, interrupt and clock circuit.
These are used in numerous automatically controlled devices like remote
controls, medical devices, automobile engine control systems, power tools,
toys, workplace machines, and different embedded systems.
12. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Inductor
An inductor or coil or a reactor is a two-terminal
passive electrical component.
It stores voltage within the form of magnetic energy.
Generally an inductor includes of a conductor.
component wound into a coil that works on the principle of Faraday’s
law of inductance.
Once a current flows through the coil from the left side to the right
side.
13. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Inductor
The coil produces a magnetic field within the clockwise direction.
The inductance of the inductor is denoted by ‘L’.
L== (µ.K.N2.S)/I.
Where,
• ‘L’ is an inductance.
• ‘K’ is a Nagaoka constant.
• ‘µ’ is a Magnetic permeability.
• ‘N’ is the number of turns of the coils.
• ‘S’ is the Cross section area of the coil.
• ‘I’ is the Length of the coil in axial direction.
14. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Transformer
A transformer is an electrical device and it consists of 2 coils of wire
that are joined by an iron core.
It has the capability of changing the current and voltage levels simply.
The main function of the transformer is that to increase (step-up) or
decrease (step-down) AC voltages.
The transformer works on the principle of Faraday’s law of
electromagnetic induction.
15. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Transformer
It means that mutual inductance between 2 circuits that is linked by
a common magnetic flux.
Transformer converts an electrical energy from one circuit to another
circuit.
With the help of mutual induction between the 2 windings without
electrical connection between them.
It converts power from one circuit to another circuit without
changing the frequency.
16. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Transformer
In a step up transformer, secondary winding
contains a lot of winding than the first coil.
Transformer has more windings in the primary
than the secondary winding.
These are one of the main reasons we use AC
current in our homes and not DC.
DC voltages can’t be modified using
transformers.
17. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Battery
A battery is an electrical device that is employed to convert chemical
energy into voltage through electrochemical discharge reactions.
Batteries are composed of one or more cells where each cell having an
anode (+), the cathode (-) and the solution.
The anode and the cathode are preserved to an electric circuit.
Batteries are classified into 2 varieties
1. Primary or disposable batteries
2. Secondary or rechargeable batteries
19. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Fuse
A fuse is a material or a bit of wire which is employed to protect the
components from destruction due to excessive current flowing through
them.
When excessive current flows through the circuit, the wires get heated
up and get broken.
When wire get broken, the current stops flowing.
When the fuse melts due to overflow of current then, the part of the
fuse absorbs some energy.
20. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Fuse
The absorbed energy is given by I2t.
Where, ‘I’ is the peak value of the current interrupted
‘t’ is the time taken to clear the fault.
When the fuse blows, it offers a signal that there is
some reasonably fault within the circuit.
A fuse element is made of Zn, copper, silver,
aluminium or alloys to afford sure characteristics.
21. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Diode/LED (Light Emitting Diode)
A diode is a device, which is made from semiconductor
material that allows current to flow in one direction.
It blocks the current that tries to travel against the flow
in a wire.
These devices are often used in several electronic
circuits that convert AC to DC.
An LED is the alternative of the diode.
22. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Diode/LED (Light Emitting Diode)
Once a current is applied to an LED; it emits light at a specific frequency.
LEDs are utilized in varied applications like.
Keyboards
Hard disks
TV remote controls
23. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Transistors
The transistor is a device, which consists of 3
terminals.
It fabricated from semiconductor material that
controls the flow of voltage or current.
It acts as a switch for electronic signals.
There are 2 varieties of transistors PNP and NPN.
24. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Transistors
Most circuits uses NPN semiconductor.
Transistors are designed in numerous shapes.
The 3 terminals of the semiconductor are the base (B), emitter (E)
and collector(C).
The base terminal is responsible for activating the transistor.
The emitter terminal is the negative lead and collector terminal is the
positive lead.
25. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Integrated Circuit
Integrated circuit is also called IC and sometimes it
is additionally known as a chip.
The integrated circuit is a semiconductor device.
It has numerous resistors, capacitors, and
transistors are fabricated.
It will operate as a microprocessor, microchip, amplifier, and timer.
An IC is classified as either linear or nonlinear depending on its application.
26. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Integrated Circuit
Linear ICs or analog integrated circuits have continuously variable O/P.
It depends on the level of i/p signal.
These linear ICs are used as audio frequency and radio frequency amplifiers.
Digital ICs operate at only some defined states, instead of over a
continuous vary of signal amplitudes.
The basic structure of digital integrated circuits is logic gates.
Integrated circuits uses in computers, modems, computer networks and
frequency counters.
27. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Relays
Relays are switches. It is used to control the circuits by employing a low
power signal.
The relays comprise of a magnet, a coil, a series of electrical contacts
and a spring.
There is no electrical connection between the two circuits within the
relay.
It is connected through the magnetic connection.
Relays are used to perform logical operations in telephone exchanges
and computers.
29. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Switches
A switch is an electrical device, it is employed to interrupt the circuit.
The switch works with ON and OFF mechanism.
It Interrupt the current and provide the current from one conductor to a
different conductor.
30. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Switches
Switches are classified into four varieties like
(SPST) Single pole single throw.
(SPDT) Single pole double throw.
(DPST) Double pole single throw.
(DPDT) Double pole double throw.
31. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Motors
A motor is an electrical device, it converts
electrical energy into mechanical energy.
The motor contains rotor, stator, bearings,
conduit box, enclosure and eye bolt.
The motors are competent for the tasks which
they perform when compared to pneumatic or
hydraulic alternatives.
32. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Motors
Motors are categorized into different types like.
AC inductance motors
DC motors And Stepper motor
Three phase induction motor
Brushless magnet electric motor
Brushed DC motor
Switched reluctance motor.
33. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Circuit Breakers
A circuit breaker is a mechanical switching device
which is operated automatically.
It used to defend an electric circuit from damage
caused by overload or short circuit.
The most functions of the circuit breaker is to
interrupt current flow and determine a fault
condition.
It includes of two contacts like moving & mounted
contacts.
34. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Circuit Breakers
Moving contact: It is to interrupt and create the circuit
victimization stored energies in the kind of spring or compressed air.
Mounted contact: Includes a spring that holds the moving contact
when closing.
These devices accommodate two coils, closing and tripping coil.
Wherever closing coil is used to shut the circuit and tripping coil is
employed to trip the circuit.
35. http://www.edgefxkits.com/
Electrical and Electronic Components
Used in Projects
Conclusion
This list offers a quick info concerning different types of
electronic and electrical components that are utilized in
various electronic and electrical projects, embedded
systems.