Automatic Street Light Controller Using Arduino
•Download as PPTX, PDF•
0 likes•3,855 views
This document describes an automatic street light controller system using Arduino that can reduce power consumption by turning lights off when roads are deserted. It uses light dependent resistors (LDRs) to sense light levels and detect faults, and PIR motion sensors to adjust light intensity based on vehicle movement. The system is controlled by an Arduino board and can send status messages to control rooms using WiFi modules. Block diagrams and code are provided to illustrate the hardware and software implementation.
Report
Share
Report
Share
Recommended
Automatic Streetlight
Automatic Streetlight System Using LDR and Arduino UNO. An electronics short project done by students of Mechanical Engineering,IUBAT. This Arduino based project will provide a competent method for lighting systems and make the whole process of energy saving easier and efficient. With a capability to change the amount of light emitted depending upon the outside condition is no doubt an innovation with many future application apart from the fact that it can also be used in many present day tech such as street light, park lights, industrial lights and many more.
Ppt on automatic street light control using ir sensors
This document describes a project to automatically control street lights using infrared sensors and a microcontroller. The system is intended to reduce energy consumption by turning lights on only when vehicles are detected. Infrared sensors detect passing vehicles and signal the microcontroller, which then turns on the appropriate street lights. When the vehicle passes, the lights will turn off again after a set time. The goal is to reduce wasted electricity while providing lighting as needed.
Automatic street light control using ldr PPT
This document describes an automatic street light control circuit using an LDR (light dependent resistor). The circuit uses an LDR, resistors, capacitors, diodes, a transistor and relay to automatically turn on LED street lights when it gets dark. When the LDR detects a drop in light levels, it causes the transistor to switch on, powering the relay and turning on the lights. The circuit requires few components, consumes little power and provides an efficient automatic method for controlling street lights without manual operation.
smart blind stick
This document describes the design of a smart electronic guiding stick for blind people. It uses multiple sensors interfaced with a microcontroller to provide alerts and feedback to help with navigation. The sensors include ultrasonic sensors for obstacle detection, IR sensors for pit and staircase detection, water and fire sensors for hazard avoidance, and a light sensor. The microcontroller outputs alerts through a buzzer, vibrator, and LEDs. Software like AVR Studio and Proteus were used. The goal is to provide a low-cost solution that makes navigation safer and more secure for blind users through real-time monitoring and dual feedback systems.
automatic streetlight control using ldr ppt
This document describes an automatic street light control circuit using an LDR (Light Dependent Resistor). The circuit uses an LM358 operational amplifier, a relay, an LDR, resistors, a capacitor, a transistor, and a lamp. It works by turning the street light on when the LDR detects low light levels and turning it off when high light levels are detected, thereby automatically controlling the street light and saving energy. The circuit was designed and simulated using Proteus software and implemented on a breadboard.
Smart street light system
This document provides a design report for a smart street light system that aims to reduce energy wastage by automatically controlling street lights based on sunlight intensity and detecting movement. The system uses an Arduino microcontroller along with light dependent resistors and infrared proximity sensors to sense the environment and control street lamp brightness accordingly. It is designed to switch lights on when sunlight is low and increase brightness when motion is detected to save electricity without compromising visibility needs. The report outlines the objectives, design considerations, components, and challenges of implementing such a system.
Automatic control of street light using LDR
Many of the people have a phobia of darkness, so to assist them in such situation, we have explained a simple circuit. It will automatically turn on street light in the way of LEDs or bulb coupled with relay. Working this circuit is very much easy and also the power consumed by the circuit is very low because of the very few components used in the circuit.
street light intensity control using micro-controller
This document describes an automatic street lighting system that uses an LDR sensor, infrared sensors, and a microcontroller to intelligently control street lights. The system turns lights on when it detects vehicles using infrared sensors and turns them off during the day based on light levels measured by the LDR sensor. This allows energy to be saved by only powering lights when needed. The system aims to reduce energy costs, greenhouse gas emissions, and maintenance costs compared to a conventional street lighting system.
Recommended
Automatic Streetlight
Automatic Streetlight System Using LDR and Arduino UNO. An electronics short project done by students of Mechanical Engineering,IUBAT. This Arduino based project will provide a competent method for lighting systems and make the whole process of energy saving easier and efficient. With a capability to change the amount of light emitted depending upon the outside condition is no doubt an innovation with many future application apart from the fact that it can also be used in many present day tech such as street light, park lights, industrial lights and many more.
Ppt on automatic street light control using ir sensors
This document describes a project to automatically control street lights using infrared sensors and a microcontroller. The system is intended to reduce energy consumption by turning lights on only when vehicles are detected. Infrared sensors detect passing vehicles and signal the microcontroller, which then turns on the appropriate street lights. When the vehicle passes, the lights will turn off again after a set time. The goal is to reduce wasted electricity while providing lighting as needed.
Automatic street light control using ldr PPT
This document describes an automatic street light control circuit using an LDR (light dependent resistor). The circuit uses an LDR, resistors, capacitors, diodes, a transistor and relay to automatically turn on LED street lights when it gets dark. When the LDR detects a drop in light levels, it causes the transistor to switch on, powering the relay and turning on the lights. The circuit requires few components, consumes little power and provides an efficient automatic method for controlling street lights without manual operation.
smart blind stick
This document describes the design of a smart electronic guiding stick for blind people. It uses multiple sensors interfaced with a microcontroller to provide alerts and feedback to help with navigation. The sensors include ultrasonic sensors for obstacle detection, IR sensors for pit and staircase detection, water and fire sensors for hazard avoidance, and a light sensor. The microcontroller outputs alerts through a buzzer, vibrator, and LEDs. Software like AVR Studio and Proteus were used. The goal is to provide a low-cost solution that makes navigation safer and more secure for blind users through real-time monitoring and dual feedback systems.
automatic streetlight control using ldr ppt
This document describes an automatic street light control circuit using an LDR (Light Dependent Resistor). The circuit uses an LM358 operational amplifier, a relay, an LDR, resistors, a capacitor, a transistor, and a lamp. It works by turning the street light on when the LDR detects low light levels and turning it off when high light levels are detected, thereby automatically controlling the street light and saving energy. The circuit was designed and simulated using Proteus software and implemented on a breadboard.
Smart street light system
This document provides a design report for a smart street light system that aims to reduce energy wastage by automatically controlling street lights based on sunlight intensity and detecting movement. The system uses an Arduino microcontroller along with light dependent resistors and infrared proximity sensors to sense the environment and control street lamp brightness accordingly. It is designed to switch lights on when sunlight is low and increase brightness when motion is detected to save electricity without compromising visibility needs. The report outlines the objectives, design considerations, components, and challenges of implementing such a system.
Automatic control of street light using LDR
Many of the people have a phobia of darkness, so to assist them in such situation, we have explained a simple circuit. It will automatically turn on street light in the way of LEDs or bulb coupled with relay. Working this circuit is very much easy and also the power consumed by the circuit is very low because of the very few components used in the circuit.
street light intensity control using micro-controller
This document describes an automatic street lighting system that uses an LDR sensor, infrared sensors, and a microcontroller to intelligently control street lights. The system turns lights on when it detects vehicles using infrared sensors and turns them off during the day based on light levels measured by the LDR sensor. This allows energy to be saved by only powering lights when needed. The system aims to reduce energy costs, greenhouse gas emissions, and maintenance costs compared to a conventional street lighting system.
LASER SECURITY SYSTEM (PPTx) PRESENTATION
This document describes a student project to design a laser security system. The system uses a laser, light dependent resistor (LDR), and other components like an LED, transistor, capacitor, resistor, buzzer, and battery. When the laser beam is interrupted by an intruder breaking the plane, the LDR detects the change and triggers the circuit to activate the buzzer alarm. The project aims to develop an affordable modern security system using laser technology to protect individuals and property from crime and threats.
Automatic street light
automatic street light that switches between both solar and electricity based on the intensity level of light using pica6f883
Automatic Room Light Controller Using Arduinom & PIR Sensor
Automatic Room Lights System using Arduino is a very useful project as you need not worry about turning on and off the switches every time you want to turn on the lights. The main components of the Automatic Room Lights project are Arduino, PIR Sensor and the Relay Module.
smart street light ppt
The document presents a smart street light system that uses sensors to detect vehicles and adjusts street light brightness accordingly to save energy. It aims to reduce wasted energy by turning lights off when no vehicles are present. The system uses IR sensors to detect vehicles, microcontrollers to control LED street lights, and PWM technique to dim lights to 10% intensity between vehicles. It is presented as an energy efficient and cost effective alternative to existing street light technologies.
Street light controllercircuit.ppt 3
This document describes a street light controller circuit that automatically turns street lights on at night and off during the day to reduce power consumption and costs. The circuit uses a light dependent resistor to sense light levels and control a relay that switches a 230V lamp. When it gets dark, the LDR resistance increases and the relay is energized, turning the lamp on. During the day when the LDR resistance decreases, the relay is de-energized and the lamp turns off. The circuit aims to eliminate the need for manual switching and reduce energy usage through automatic operation based on light levels.
automatic light control at night ppt by Shubhan raj
This document presents a project on an automatic light control circuit that can switch lights on and off without manual operation based on ambient light levels. The circuit uses an LDR sensor to detect light intensity and control a relay driver IC and relay to power the lights. It includes sections describing the hardware requirements, circuit diagram, components, simulation, PCB layout, advantages, and conclusions. The system is intended to automatically control lights to save electricity while requiring minimal maintenance.
INFRARED SENSOR WORKING PRINCIPLE AND CIRCUIT
This document summarizes an active learning assignment on infrared sensors. It introduces the topic, explaining that IR sensors are used to detect obstacles like human vision. It then describes the basic components of an IR sensor including the IR LED transmitter, photodiode receiver, and comparator circuitry. The document explains that the IR LED transmits light which bounces off objects and is detected by the photodiode, with the output compared to a reference voltage. Finally, it outlines some common applications of IR sensors and their pros and cons.
Automatic light control Using LDR
This project name also called Automatic dark detector using LDR or automatic Light detector using LDR.
smart helmet
This document describes the implementation of a smart helmet system using solar power. The system includes an alcohol sensor, temperature sensor, vibration sensor, GPS module, GSM module, and microcontroller to provide safety features like detecting accidents, monitoring alcohol levels, tracking location, and regulating temperature. The smart helmet aims to reduce accidents by preventing intoxicated riding and automatically alerting emergency contacts in the event of a crash. It can also be used to remotely immobilize a vehicle if the helmet is removed or stolen. The system design uses low power components like a solar cell to allow for portable operation.
AUTOMATIC RAILWAY GATE CONTROL SYSTEM
This document presents a technical presentation on an automatic railway gate control system. The main aim of the project is to automate unmanned railway gates so that the gate closes automatically when a train approaches and opens after the train passes. It works using IR sensors to detect the train's approach and a microcontroller that controls stepper motors to open and close the gate. When a train is detected, the gate closes to prevent accidents at the railway crossing. This automatic system helps reduce accidents by removing human error.
Automatic led night lamp
The document describes an automatic LED night lamp project that uses light dependent resistors and integrated circuits to turn on a night lamp when it gets dark and sound an alarm in the morning when it gets light. The key components are an NE555 timer IC, UM66 music generator IC, light dependent resistors, LED, speaker and other passive components. When the light sensor detects darkness, the NE555 timer turns on the LED night lamp. In the morning, the sensor detects light and the UM66 IC sounds a musical alarm through the speaker. The circuit aims to provide light at night for tasks like reading and wake the user up gently in the morning.
IoT Based Garbage Monitoring System ppt
1) A group of students presented on an IOT Garbage Monitoring System to help keep cities clean.
2) The system uses ultrasonic sensors and a microcontroller to monitor garbage levels in bins and displays the status on an LCD screen and web page.
3) When fully implemented, the system will help support initiatives like Swachh Bharat Mission by enabling real-time garbage monitoring and efficient collection.
Automatic street light control system
This document describes an automatic street light control system that uses a light dependent resistor and op-amp circuit to switch street lights on and off automatically based on light levels. It aims to reduce energy consumption by preventing lights from staying on during the day or taking too long to turn on at night. The system detects darkness and uses a relay to switch on lights without manual operation. It is powered by a 12V DC supply and can be modified to charge during the day using solar energy.
Electronics project presentation
This is a project presentation for our electronics lab .The name of our project is cell phone detector.
Density based Traffic Light Controller
This document describes a density-based traffic light controller system that uses sensors to measure traffic load and detect emergency vehicles. The system uses a microcontroller to automatically adjust signal timing based on traffic density during normal operation. When an emergency vehicle is detected, the system overrides normal timing to provide a green light in the direction of the emergency vehicle while blocking other lanes. The system is intended to help reduce traffic jams by adapting to current traffic conditions. Key components include IR sensors to detect vehicles, a microcontroller to control signal timing, and an RF receiver to detect emergency vehicles like ambulances.
ACCIDENT DETECTION SYSTEM PPT
This presentation includes what is accident detection system ppt ,what are its requirements and how its works and its advantages,disadvantages and applications,Results and future sccope and at last conclusion
Auto control street lights
This document describes a project to automatically control street light intensity using different dimming methods for high pressure sodium lamps and LEDs. For sodium lamps, a triac circuit uses pulse width modulation to vary the conduction angle and adjust brightness. For LEDs, an IGBT circuit also uses PWM to control the duty cycle fed to the lights. Simulation results show how brightness changes as the conduction angle and duty cycle are varied. Automatic dimming based on time of night can reduce energy costs for street lighting.
arduino based automatic irrigation system
This document describes an Arduino-based automatic irrigation system. The system uses soil moisture and temperature sensors to monitor soil conditions. When the soil moisture drops below a threshold, a relay connected to an Arduino board activates a water pump to irrigate. The system aims to minimize manual intervention by farmers and prevent over- or under-watering. It provides a schematic diagram of the circuit components, which include an Arduino Uno, sensors, LCD display, and relay module. The document also includes photos of the prototype and discusses the benefits of automating irrigation.
Smart street light detector
smart street light detector based on sensors. This is basically designed to reduce the power consumption of the street light. And help out to conserve more and more energy.
automatic room light controller
This document outlines a project to design and construct an automatic room light controller with a bidirectional visitor counter. It aims to limit power waste by turning lights off when rooms are empty and automatically turning them on when people enter. The system will incorporate transmitters, receivers, and relays to detect presence and absence and control lights accordingly. It will also count the number of people in a room at a given time. The project scope includes use in schools, offices, and conference halls to conserve electricity without inconveniencing visitors.
Presentation-WPS Office.pptx
This document describes an automatic street light control system that uses a light dependent resistor (LDR) sensor to detect light levels and switch street lights on and off without manual operation. When the LDR sensor detects darkness above a certain level, it activates a transistor switch to turn on the lights. The system gets its power from a solar panel and battery, providing a renewable energy source. It has advantages of being low cost, using automated operation and low power consumption. Potential disadvantages include risk of theft and needing to replace rechargeable batteries over time. The system has applications for street, yard, park and industrial lighting.
Group project progree
This document describes a home automation system proposed by a group of students. The system uses a PLC and microcontrollers to control the home's gate, lights, and intruder detection systems. Sensors like infrared and ultrasonic sensors detect intruders and control the gate and lights, while components like relays, transistors, and a stepper motor help operate the automation. The group's proposed solution uses these technologies in a circuit to remotely control and secure the home.
More Related Content
What's hot
LASER SECURITY SYSTEM (PPTx) PRESENTATION
This document describes a student project to design a laser security system. The system uses a laser, light dependent resistor (LDR), and other components like an LED, transistor, capacitor, resistor, buzzer, and battery. When the laser beam is interrupted by an intruder breaking the plane, the LDR detects the change and triggers the circuit to activate the buzzer alarm. The project aims to develop an affordable modern security system using laser technology to protect individuals and property from crime and threats.
Automatic street light
automatic street light that switches between both solar and electricity based on the intensity level of light using pica6f883
Automatic Room Light Controller Using Arduinom & PIR Sensor
Automatic Room Lights System using Arduino is a very useful project as you need not worry about turning on and off the switches every time you want to turn on the lights. The main components of the Automatic Room Lights project are Arduino, PIR Sensor and the Relay Module.
smart street light ppt
The document presents a smart street light system that uses sensors to detect vehicles and adjusts street light brightness accordingly to save energy. It aims to reduce wasted energy by turning lights off when no vehicles are present. The system uses IR sensors to detect vehicles, microcontrollers to control LED street lights, and PWM technique to dim lights to 10% intensity between vehicles. It is presented as an energy efficient and cost effective alternative to existing street light technologies.
Street light controllercircuit.ppt 3
This document describes a street light controller circuit that automatically turns street lights on at night and off during the day to reduce power consumption and costs. The circuit uses a light dependent resistor to sense light levels and control a relay that switches a 230V lamp. When it gets dark, the LDR resistance increases and the relay is energized, turning the lamp on. During the day when the LDR resistance decreases, the relay is de-energized and the lamp turns off. The circuit aims to eliminate the need for manual switching and reduce energy usage through automatic operation based on light levels.
automatic light control at night ppt by Shubhan raj
This document presents a project on an automatic light control circuit that can switch lights on and off without manual operation based on ambient light levels. The circuit uses an LDR sensor to detect light intensity and control a relay driver IC and relay to power the lights. It includes sections describing the hardware requirements, circuit diagram, components, simulation, PCB layout, advantages, and conclusions. The system is intended to automatically control lights to save electricity while requiring minimal maintenance.
INFRARED SENSOR WORKING PRINCIPLE AND CIRCUIT
This document summarizes an active learning assignment on infrared sensors. It introduces the topic, explaining that IR sensors are used to detect obstacles like human vision. It then describes the basic components of an IR sensor including the IR LED transmitter, photodiode receiver, and comparator circuitry. The document explains that the IR LED transmits light which bounces off objects and is detected by the photodiode, with the output compared to a reference voltage. Finally, it outlines some common applications of IR sensors and their pros and cons.
Automatic light control Using LDR
This project name also called Automatic dark detector using LDR or automatic Light detector using LDR.
smart helmet
This document describes the implementation of a smart helmet system using solar power. The system includes an alcohol sensor, temperature sensor, vibration sensor, GPS module, GSM module, and microcontroller to provide safety features like detecting accidents, monitoring alcohol levels, tracking location, and regulating temperature. The smart helmet aims to reduce accidents by preventing intoxicated riding and automatically alerting emergency contacts in the event of a crash. It can also be used to remotely immobilize a vehicle if the helmet is removed or stolen. The system design uses low power components like a solar cell to allow for portable operation.
AUTOMATIC RAILWAY GATE CONTROL SYSTEM
This document presents a technical presentation on an automatic railway gate control system. The main aim of the project is to automate unmanned railway gates so that the gate closes automatically when a train approaches and opens after the train passes. It works using IR sensors to detect the train's approach and a microcontroller that controls stepper motors to open and close the gate. When a train is detected, the gate closes to prevent accidents at the railway crossing. This automatic system helps reduce accidents by removing human error.
Automatic led night lamp
The document describes an automatic LED night lamp project that uses light dependent resistors and integrated circuits to turn on a night lamp when it gets dark and sound an alarm in the morning when it gets light. The key components are an NE555 timer IC, UM66 music generator IC, light dependent resistors, LED, speaker and other passive components. When the light sensor detects darkness, the NE555 timer turns on the LED night lamp. In the morning, the sensor detects light and the UM66 IC sounds a musical alarm through the speaker. The circuit aims to provide light at night for tasks like reading and wake the user up gently in the morning.
IoT Based Garbage Monitoring System ppt
1) A group of students presented on an IOT Garbage Monitoring System to help keep cities clean.
2) The system uses ultrasonic sensors and a microcontroller to monitor garbage levels in bins and displays the status on an LCD screen and web page.
3) When fully implemented, the system will help support initiatives like Swachh Bharat Mission by enabling real-time garbage monitoring and efficient collection.
Automatic street light control system
This document describes an automatic street light control system that uses a light dependent resistor and op-amp circuit to switch street lights on and off automatically based on light levels. It aims to reduce energy consumption by preventing lights from staying on during the day or taking too long to turn on at night. The system detects darkness and uses a relay to switch on lights without manual operation. It is powered by a 12V DC supply and can be modified to charge during the day using solar energy.
Electronics project presentation
This is a project presentation for our electronics lab .The name of our project is cell phone detector.
Density based Traffic Light Controller
This document describes a density-based traffic light controller system that uses sensors to measure traffic load and detect emergency vehicles. The system uses a microcontroller to automatically adjust signal timing based on traffic density during normal operation. When an emergency vehicle is detected, the system overrides normal timing to provide a green light in the direction of the emergency vehicle while blocking other lanes. The system is intended to help reduce traffic jams by adapting to current traffic conditions. Key components include IR sensors to detect vehicles, a microcontroller to control signal timing, and an RF receiver to detect emergency vehicles like ambulances.
ACCIDENT DETECTION SYSTEM PPT
This presentation includes what is accident detection system ppt ,what are its requirements and how its works and its advantages,disadvantages and applications,Results and future sccope and at last conclusion
Auto control street lights
This document describes a project to automatically control street light intensity using different dimming methods for high pressure sodium lamps and LEDs. For sodium lamps, a triac circuit uses pulse width modulation to vary the conduction angle and adjust brightness. For LEDs, an IGBT circuit also uses PWM to control the duty cycle fed to the lights. Simulation results show how brightness changes as the conduction angle and duty cycle are varied. Automatic dimming based on time of night can reduce energy costs for street lighting.
arduino based automatic irrigation system
This document describes an Arduino-based automatic irrigation system. The system uses soil moisture and temperature sensors to monitor soil conditions. When the soil moisture drops below a threshold, a relay connected to an Arduino board activates a water pump to irrigate. The system aims to minimize manual intervention by farmers and prevent over- or under-watering. It provides a schematic diagram of the circuit components, which include an Arduino Uno, sensors, LCD display, and relay module. The document also includes photos of the prototype and discusses the benefits of automating irrigation.
Smart street light detector
smart street light detector based on sensors. This is basically designed to reduce the power consumption of the street light. And help out to conserve more and more energy.
automatic room light controller
This document outlines a project to design and construct an automatic room light controller with a bidirectional visitor counter. It aims to limit power waste by turning lights off when rooms are empty and automatically turning them on when people enter. The system will incorporate transmitters, receivers, and relays to detect presence and absence and control lights accordingly. It will also count the number of people in a room at a given time. The project scope includes use in schools, offices, and conference halls to conserve electricity without inconveniencing visitors.
What's hot (20)
Automatic Room Light Controller Using Arduinom & PIR Sensor
Automatic Room Light Controller Using Arduinom & PIR Sensor
automatic light control at night ppt by Shubhan raj
automatic light control at night ppt by Shubhan raj
Similar to Automatic Street Light Controller Using Arduino
Presentation-WPS Office.pptx
This document describes an automatic street light control system that uses a light dependent resistor (LDR) sensor to detect light levels and switch street lights on and off without manual operation. When the LDR sensor detects darkness above a certain level, it activates a transistor switch to turn on the lights. The system gets its power from a solar panel and battery, providing a renewable energy source. It has advantages of being low cost, using automated operation and low power consumption. Potential disadvantages include risk of theft and needing to replace rechargeable batteries over time. The system has applications for street, yard, park and industrial lighting.
Group project progree
This document describes a home automation system proposed by a group of students. The system uses a PLC and microcontrollers to control the home's gate, lights, and intruder detection systems. Sensors like infrared and ultrasonic sensors detect intruders and control the gate and lights, while components like relays, transistors, and a stepper motor help operate the automation. The group's proposed solution uses these technologies in a circuit to remotely control and secure the home.
Smart street lighting control system project PPT
This document contains details about a smart street light control system project. It lists the batch members and project guide. The objectives are to reduce energy consumption and inform authorities about any incidents or street light faults using sensors, a camera and GSM modem. It describes the components used like PIR sensor, vibration sensor, camera, microcontroller. It also explains how ThingSpeak cloud platform can be used to store and access real-time sensor data through mobile phones.
PRESENTATION PRACTICAL TASK (A) MINI PROJECT-2.pptx
This document describes an automatic street light control system project using an LDR sensor. It contains an introduction to open and closed loop control systems. The automatic street light system uses an LDR sensor to detect light levels and a transistor switch to turn the street light on in low light and off in high light, reducing energy consumption. The circuit diagram and components used including the LDR, LED, transistor, and resistor are explained. Advantages of using the LDR for energy savings are outlined along with some disadvantages. Suggestions for improving the system using infrared sensors or a phototransistor are provided.
IRJET- Automatic Highway Lighting System
This document describes an automatic highway lighting system that uses sensors to detect vehicle movement and controls highway lighting accordingly to save energy. Infrared sensors placed along the highway detect approaching vehicles and signal a microcontroller to turn on a block of lights ahead of the vehicle. As the vehicle passes, the lights behind it are automatically turned off. When no vehicles are present, all the lights remain off. This system aims to reduce energy consumption compared to conventional highway lighting that remains on all night.
Intelligent street lights 2
Intelligent street lights improve on automatic street lights by including a GSM modem and power saving algorithms. The GSM modem allows the intelligent street lights to send SMS messages to alert linemen and municipal officers if a light fails or burns out, allowing for faster repairs. Power saving algorithms enable all lights during expected heavy traffic periods but disable lights one by one at other times to conserve power. These improvements give the street lights intelligence to report issues and know when all lights are needed.
Automatic Head Light Intensity control for avoid accidents at night times..pptx
This document describes a proposed system for automatic headlight intensity control to avoid accidents. The system uses an LDR sensor and ultrasonic sensor along with a microcontroller to automatically adjust the headlight intensity based on surrounding light levels and detected objects. When the LDR sensor detects a high intensity of light and the ultrasonic sensor detects an object, the headlights will be dimmed to the low beam setting to prevent glare. If darkness is detected but no object is present, the headlights will remain on high beam. The system aims to prevent accidents caused by glare from opposing vehicles' headlights during night driving.
Smart street light system
This document describes the design of a smart street light system that uses sensors and a microcontroller to automatically control street lights. The system aims to reduce energy waste by switching lights on only when motion is detected and adjusting brightness based on sunlight levels. Key components include infrared and proximity sensors to detect vehicles, an Arduino microcontroller to control the lights, and a light dependent resistor to measure sunlight intensity and determine when to turn lights on or off. The document outlines the problem, objectives, design constraints, system features and components.
Density based traffic signal control using microcontroller
Description : This project includes controller ATmega 32A, Led (blue,red,yellow), IR sensor modules.
Specification : Power supply (12 v -1amp), frequency of controller Atmega 32A is 8 Mhz, range of IR
module is 1m and frequency of IR module is 32KHz.
Method of work : 1.Design of circuit
2. Programming in ICC AVR.
3. Simulation of design through Proteus.
automatic street light control using aurdino,PIR,LDR tinker cad circuit
This document describes an automatic street light control system that uses PIR sensors and LDR sensors to reduce energy waste. The system aims to automatically switch street lights on when motion is detected and regulate the lights based on available natural light. It consists of an Arduino, PIR sensors, LDR sensors, an LCD display, resistors, and bulbs. When a PIR sensor detects a vehicle, the corresponding street light will turn on and remain on for a set time before switching off. The LDR sensors monitor light levels and regulate street light intensity during day and night. This automatic control system is expected to significantly reduce unnecessary street light use and wastage of electricity.
Auto turning outdoor light
The document describes an automated outdoor light circuit that uses an LDR light sensor and NPN transistor to turn a light on and off based on light intensity levels. The circuit aims to reduce human effort in controlling lights and lower power consumption. It works by using an LDR light sensor to detect light levels and trigger an NPN transistor switch to power a light. The automated light system has applications for street lights, home exterior lights, and outdoor gardens. It provides effortless and economical light control but has limitations in response time and issues measuring light levels.
ELECTRONIC EYE FOR NIGHT DEVICE SWITCHING USING 555 TIMER
HEAR USING PIR AND LDR SENSORS WE CONTROLLED LIGHT TO GLOW IN NIGHT TIMES THAT TO IN THE PRESENCE OF HUMAN.
Street controlling ppt
This document describes an intelligent and weather adaptive smart street lighting controlling system. It aims to reduce energy consumption of street lights by automating their operation based on factors like time of day, weather conditions, and presence of people/vehicles. The proposed system uses wireless communication between LED street lights equipped with sensors and a central control unit to automatically switch lights on and off instead of the existing manual process. This is expected to cut municipal lighting costs by 50-70% while reducing light pollution, CO2 emissions, and maintenance costs compared to traditional street lighting systems.
Ppt on automatic solar tracking system
This document describes the design and implementation of a dual-axis solar tracking system. It discusses the need for solar trackers to improve efficiency over stationary panels, provides an overview of the hardware and software components used including solar panels, LDR sensors, servo motors, microcontroller, and introduces the block diagrams and flow charts of the system. It also presents the simulation results, cost analysis, applications and concludes that such a tracking system can effectively increase energy generation for small to medium scale power needs.
Micro controller based Traffic control system
This project deals with traffic system controlled by a microcontroller.
using IR controllers instead of using old timing circuits.
This system aims to provide much better and safer way of controlling Traffic signal system.
This system of controlling will help a lot in future.
DESIGN AND DEVELOPMENT OF SUN TRACKER SOLAR POWER
A solar tracker system was designed and developed to increase the efficiency of solar panels. It uses a stepper motor, actuator, microcontroller and other components to orient solar panels toward the sun for maximum energy generation. By continuously tracking the sun's movement, the system can increase efficiency by 25-35% compared to fixed panels. It is useful for power generation in remote areas without electricity grids and can help reduce emissions from other power sources. While the initial investment is high, solar tracking provides flexibility and higher long-term returns from cleaner energy production.
Mini Project
This document describes a proposed obstacle collision prevention system that uses an ultrasonic sensor mounted on a vehicle's bumper to detect obstacles and an Arduino microcontroller to automatically apply the brakes if an obstacle gets too close, aiming to reduce accidents by providing an automatic braking system without relying solely on human response time; it discusses the existing braking systems, proposed system design and components, advantages over existing systems, and possibilities for future enhancements.
Renewable energy resources for highway lighting
This project aims to design a prototype highway that can generate its own electricity through renewable energy sources. The prototype captures wind energy created by passing traffic, solar energy from sunlight, and piezoelectric energy from vehicle pressure. The energies are combined and stored in batteries, which power streetlights and reduce the highway's energy needs. The design uses an Arduino Nano, piezoelectric generators, an LCD display, a relay, and an LDR to integrate the renewable sources and control energy distribution. If implemented, it could transform highways into smart systems that independently and sustainably meet their own energy demands.
PLS 2016: SMART CITIES - Is there a place for solar in the Smart City?
PLS 2016: SMART CITIES - Is there a place for solar in the Smart City?Institution of Lighting Professionals
Solar power can play an important role in smart cities by powering sensors and devices anywhere they are needed, without the cost and disruption of running power lines. Small solar panels and batteries can provide reliable power for systems that monitor conditions like traffic, temperature, and air quality. These solar-powered smart devices can wirelessly transmit data to help cities efficiently manage resources and infrastructure in real-time, improving traffic flow, targeting road gritting, and more. By deploying sensors wherever useful data can be collected, solar power allows smart cities to maximize information gathering and decision making.Arduino based Automatic Solar Tracker.pptx
This document presents a synopsis for an automatic solar tracker using an Arduino. It discusses how solar trackers can increase energy gains from PV systems by up to 35% by orienting them towards the sun. It then describes the dual-axis solar tracker prototype, which uses two LDR sensors and servo motors connected to an Arduino to adjust the position of a solar panel based on sunlight readings. The circuit diagram and working principle are explained. Key hardware components including the solar panel, motors, sensors and Arduino are also described. Applications include power generation and potential future developments like integrated street lighting.
Similar to Automatic Street Light Controller Using Arduino (20)
PRESENTATION PRACTICAL TASK (A) MINI PROJECT-2.pptx
PRESENTATION PRACTICAL TASK (A) MINI PROJECT-2.pptx
Automatic Head Light Intensity control for avoid accidents at night times..pptx
Automatic Head Light Intensity control for avoid accidents at night times..pptx
Density based traffic signal control using microcontroller
Density based traffic signal control using microcontroller
automatic street light control using aurdino,PIR,LDR tinker cad circuit
automatic street light control using aurdino,PIR,LDR tinker cad circuit
ELECTRONIC EYE FOR NIGHT DEVICE SWITCHING USING 555 TIMER
ELECTRONIC EYE FOR NIGHT DEVICE SWITCHING USING 555 TIMER
PLS 2016: SMART CITIES - Is there a place for solar in the Smart City?
PLS 2016: SMART CITIES - Is there a place for solar in the Smart City?
Recently uploaded
一比一原版(CalArts毕业证)加利福尼亚艺术学院毕业证如何办理
CalArts毕业证学历书【微信95270640】CalArts毕业证’圣力嘉学院毕业证《Q微信95270640》办理CalArts毕业证√文凭学历制作{CalArts文凭}购买学历学位证书本科硕士,CalArts毕业证学历学位证【实体公司】办毕业证、成绩单、学历认证、学位证、文凭认证、办留信网认证、（网上可查，实体公司，专业可靠）
(诚招代理)办理国外高校毕业证成绩单文凭学位证,真实使馆公证（留学回国人员证明）真实留信网认证国外学历学位认证雅思代考国外学校代申请名校保录开请假条改GPA改成绩ID卡
1.高仿业务:【本科硕士】毕业证,成绩单（GPA修改）,学历认证（教育部认证）,大学Offer,,ID,留信认证,使馆认证,雅思,语言证书等高仿类证书；
2.认证服务: 学历认证（教育部认证）,大使馆认证（回国人员证明）,留信认证（可查有编号证书）,大学保录取,雅思保分成绩单。
3.技术服务：钢印水印烫金激光防伪凹凸版设计印刷激凸温感光标底纹镭射速度快。
办理加利福尼亚艺术学院加利福尼亚艺术学院毕业证文凭证书流程：
1客户提供办理信息：姓名生日专业学位毕业时间等（如信息不确定可以咨询顾问：我们有专业老师帮你查询）；
2开始安排制作毕业证成绩单电子图；
3毕业证成绩单电子版做好以后发送给您确认；
4毕业证成绩单电子版您确认信息无误之后安排制作成品；
5成品做好拍照或者视频给您确认；
6快递给客户（国内顺丰国外DHLUPS等快读邮寄）
-办理真实使馆公证（即留学回国人员证明）
-办理各国各大学文凭（世界名校一对一专业服务,可全程监控跟踪进度）
-全套服务：毕业证成绩单真实使馆公证真实教育部认证。让您回国发展信心十足！
（详情请加一下 文凭顾问+微信:95270640）欢迎咨询！子小伍玩小伍比山娃小一岁虎头虎脑的很霸气父亲让山娃跟小伍去夏令营听课山娃很高兴夏令营就设在附近一所小学山娃发现那所小学比自己的学校更大更美操场上还铺有塑胶跑道呢里面很多小朋友一班一班的快快乐乐原来城里娃都藏这儿来了怪不得平时见不到他们山娃恍然大悟起来吹拉弹唱琴棋书画山娃都不懂却什么都想学山娃怨自己太笨什么都不会斟酌再三山娃终于选定了学美术当听说每月要交元时父亲犹豫了山娃也说爸算了吧咱学校一学期才转
Redefining brain tumor segmentation: a cutting-edge convolutional neural netw...
Medical image analysis has witnessed significant advancements with deep learning techniques. In the domain of brain tumor segmentation, the ability to
precisely delineate tumor boundaries from magnetic resonance imaging (MRI)
scans holds profound implications for diagnosis. This study presents an ensemble convolutional neural network (CNN) with transfer learning, integrating
the state-of-the-art Deeplabv3+ architecture with the ResNet18 backbone. The
model is rigorously trained and evaluated, exhibiting remarkable performance
metrics, including an impressive global accuracy of 99.286%, a high-class accuracy of 82.191%, a mean intersection over union (IoU) of 79.900%, a weighted
IoU of 98.620%, and a Boundary F1 (BF) score of 83.303%. Notably, a detailed comparative analysis with existing methods showcases the superiority of
our proposed model. These findings underscore the model’s competence in precise brain tumor localization, underscoring its potential to revolutionize medical
image analysis and enhance healthcare outcomes. This research paves the way
for future exploration and optimization of advanced CNN models in medical
imaging, emphasizing addressing false positives and resource efficiency.
Data Driven Maintenance | UReason Webinar
Discover the latest insights on Data Driven Maintenance with our comprehensive webinar presentation. Learn about traditional maintenance challenges, the right approach to utilizing data, and the benefits of adopting a Data Driven Maintenance strategy. Explore real-world examples, industry best practices, and innovative solutions like FMECA and the D3M model. This presentation, led by expert Jules Oudmans, is essential for asset owners looking to optimize their maintenance processes and leverage digital technologies for improved efficiency and performance. Download now to stay ahead in the evolving maintenance landscape.
官方认证美国密歇根州立大学毕业证学位证书原版一模一样
原版一模一样【微信：741003700 】【美国密歇根州立大学毕业证学位证书】【微信：741003700 】学位证，留信认证（真实可查，永久存档）offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原海外各大学 Bachelor Diploma degree, Master Degree Diploma
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问Q/微741003700
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
Embedded machine learning-based road conditions and driving behavior monitoring
Car accident rates have increased in recent years, resulting in losses in human lives, properties, and other financial costs. An embedded machine learning-based system is developed to address this critical issue. The system can monitor road conditions, detect driving patterns, and identify aggressive driving behaviors. The system is based on neural networks trained on a comprehensive dataset of driving events, driving styles, and road conditions. The system effectively detects potential risks and helps mitigate the frequency and impact of accidents. The primary goal is to ensure the safety of drivers and vehicles. Collecting data involved gathering information on three key road events: normal street and normal drive, speed bumps, circular yellow speed bumps, and three aggressive driving actions: sudden start, sudden stop, and sudden entry. The gathered data is processed and analyzed using a machine learning system designed for limited power and memory devices. The developed system resulted in 91.9% accuracy, 93.6% precision, and 92% recall. The achieved inference time on an Arduino Nano 33 BLE Sense with a 32-bit CPU running at 64 MHz is 34 ms and requires 2.6 kB peak RAM and 139.9 kB program flash memory, making it suitable for resource-constrained embedded systems.
IEEE Aerospace and Electronic Systems Society as a Graduate Student Member
IEEE Aerospace and Electronic Systems Society as a Graduate Student Member
Null Bangalore | Pentesters Approach to AWS IAM
#Abstract:
- Learn more about the real-world methods for auditing AWS IAM (Identity and Access Management) as a pentester. So let us proceed with a brief discussion of IAM as well as some typical misconfigurations and their potential exploits in order to reinforce the understanding of IAM security best practices.
- Gain actionable insights into AWS IAM policies and roles, using hands on approach.
#Prerequisites:
- Basic understanding of AWS services and architecture
- Familiarity with cloud security concepts
- Experience using the AWS Management Console or AWS CLI.
- For hands on lab create account on [killercoda.com](https://killercoda.com/cloudsecurity-scenario/)
# Scenario Covered:
- Basics of IAM in AWS
- Implementing IAM Policies with Least Privilege to Manage S3 Bucket
- Objective: Create an S3 bucket with least privilege IAM policy and validate access.
- Steps:
- Create S3 bucket.
- Attach least privilege policy to IAM user.
- Validate access.
- Exploiting IAM PassRole Misconfiguration
-Allows a user to pass a specific IAM role to an AWS service (ec2), typically used for service access delegation. Then exploit PassRole Misconfiguration granting unauthorized access to sensitive resources.
- Objective: Demonstrate how a PassRole misconfiguration can grant unauthorized access.
- Steps:
- Allow user to pass IAM role to EC2.
- Exploit misconfiguration for unauthorized access.
- Access sensitive resources.
- Exploiting IAM AssumeRole Misconfiguration with Overly Permissive Role
- An overly permissive IAM role configuration can lead to privilege escalation by creating a role with administrative privileges and allow a user to assume this role.
- Objective: Show how overly permissive IAM roles can lead to privilege escalation.
- Steps:
- Create role with administrative privileges.
- Allow user to assume the role.
- Perform administrative actions.
- Differentiation between PassRole vs AssumeRole
Try at [killercoda.com](https://killercoda.com/cloudsecurity-scenario/)
Comparative analysis between traditional aquaponics and reconstructed aquapon...
The aquaponic system of planting is a method that does not require soil usage. It is a method that only needs water, fish, lava rocks (a substitute for soil), and plants. Aquaponic systems are sustainable and environmentally friendly. Its use not only helps to plant in small spaces but also helps reduce artificial chemical use and minimizes excess water use, as aquaponics consumes 90% less water than soil-based gardening. The study applied a descriptive and experimental design to assess and compare conventional and reconstructed aquaponic methods for reproducing tomatoes. The researchers created an observation checklist to determine the significant factors of the study. The study aims to determine the significant difference between traditional aquaponics and reconstructed aquaponics systems propagating tomatoes in terms of height, weight, girth, and number of fruits. The reconstructed aquaponics system’s higher growth yield results in a much more nourished crop than the traditional aquaponics system. It is superior in its number of fruits, height, weight, and girth measurement. Moreover, the reconstructed aquaponics system is proven to eliminate all the hindrances present in the traditional aquaponics system, which are overcrowding of fish, algae growth, pest problems, contaminated water, and dead fish.
Mechanical Engineering on AAI Summer Training Report-003.pdf
Mechanical Engineering PROJECT REPORT ON SUMMER VOCATIONAL TRAINING
AT MBB AIRPORT
Rainfall intensity duration frequency curve statistical analysis and modeling...
Using data from 41 years in Patna’ India’ the study’s goal is to analyze the trends of how often it rains on a weekly, seasonal, and annual basis (1981−2020). First, utilizing the intensity-duration-frequency (IDF) curve and the relationship by statistically analyzing rainfall’ the historical rainfall data set for Patna’ India’ during a 41 year period (1981−2020), was evaluated for its quality. Changes in the hydrologic cycle as a result of increased greenhouse gas emissions are expected to induce variations in the intensity, length, and frequency of precipitation events. One strategy to lessen vulnerability is to quantify probable changes and adapt to them. Techniques such as log-normal, normal, and Gumbel are used (EV-I). Distributions were created with durations of 1, 2, 3, 6, and 24 h and return times of 2, 5, 10, 25, and 100 years. There were also mathematical correlations discovered between rainfall and recurrence interval.
Findings: Based on findings, the Gumbel approach produced the highest intensity values, whereas the other approaches produced values that were close to each other. The data indicates that 461.9 mm of rain fell during the monsoon season’s 301st week. However, it was found that the 29th week had the greatest average rainfall, 92.6 mm. With 952.6 mm on average, the monsoon season saw the highest rainfall. Calculations revealed that the yearly rainfall averaged 1171.1 mm. Using Weibull’s method, the study was subsequently expanded to examine rainfall distribution at different recurrence intervals of 2, 5, 10, and 25 years. Rainfall and recurrence interval mathematical correlations were also developed. Further regression analysis revealed that short wave irrigation, wind direction, wind speed, pressure, relative humidity, and temperature all had a substantial influence on rainfall.
Originality and value: The results of the rainfall IDF curves can provide useful information to policymakers in making appropriate decisions in managing and minimizing floods in the study area.
学校原版美国波士顿大学毕业证学历学位证书原版一模一样
原版一模一样【微信：741003700 】【美国波士顿大学毕业证学历学位证书】【微信：741003700 】学位证，留信认证（真实可查，永久存档）offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原海外各大学 Bachelor Diploma degree, Master Degree Diploma
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问Q/微741003700
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
Optimizing Gradle Builds - Gradle DPE Tour Berlin 2024
Sinan from the Delivery Hero mobile infrastructure engineering team shares a deep dive into performance acceleration with Gradle build cache optimizations. Sinan shares their journey into solving complex build-cache problems that affect Gradle builds. By understanding the challenges and solutions found in our journey, we aim to demonstrate the possibilities for faster builds. The case study reveals how overlapping outputs and cache misconfigurations led to significant increases in build times, especially as the project scaled up with numerous modules using Paparazzi tests. The journey from diagnosing to defeating cache issues offers invaluable lessons on maintaining cache integrity without sacrificing functionality.
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...
Climate change's impact on the planet forced the United Nations and governments to promote green energies and electric transportation. The deployments of photovoltaic (PV) and electric vehicle (EV) systems gained stronger momentum due to their numerous advantages over fossil fuel types. The advantages go beyond sustainability to reach financial support and stability. The work in this paper introduces the hybrid system between PV and EV to support industrial and commercial plants. This paper covers the theoretical framework of the proposed hybrid system including the required equation to complete the cost analysis when PV and EV are present. In addition, the proposed design diagram which sets the priorities and requirements of the system is presented. The proposed approach allows setup to advance their power stability, especially during power outages. The presented information supports researchers and plant owners to complete the necessary analysis while promoting the deployment of clean energy. The result of a case study that represents a dairy milk farmer supports the theoretical works and highlights its advanced benefits to existing plants. The short return on investment of the proposed approach supports the paper's novelty approach for the sustainable electrical system. In addition, the proposed system allows for an isolated power setup without the need for a transmission line which enhances the safety of the electrical network
Unit-III-ELECTROCHEMICAL STORAGE DEVICES.ppt
Batteries -Introduction – Types of Batteries – discharging and charging of battery - characteristics of battery –battery rating- various tests on battery- – Primary battery: silver button cell- Secondary battery :Ni-Cd battery-modern battery: lithium ion battery-maintenance of batteries-choices of batteries for electric vehicle applications.
Fuel Cells: Introduction- importance and classification of fuel cells - description, principle, components, applications of fuel cells: H2-O2 fuel cell, alkaline fuel cell, molten carbonate fuel cell and direct methanol fuel cells.
BRAIN TUMOR DETECTION for seminar ppt.pdf
BRAIN TUMOR DETECTION
AND CLASSIFICATION USING
ARTIFICIAL INTELLIGENCE
Recently uploaded (20)
Redefining brain tumor segmentation: a cutting-edge convolutional neural netw...
Redefining brain tumor segmentation: a cutting-edge convolutional neural netw...
Embedded machine learning-based road conditions and driving behavior monitoring
Embedded machine learning-based road conditions and driving behavior monitoring
IEEE Aerospace and Electronic Systems Society as a Graduate Student Member
IEEE Aerospace and Electronic Systems Society as a Graduate Student Member
Comparative analysis between traditional aquaponics and reconstructed aquapon...
Comparative analysis between traditional aquaponics and reconstructed aquapon...
Mechanical Engineering on AAI Summer Training Report-003.pdf
Mechanical Engineering on AAI Summer Training Report-003.pdf
Rainfall intensity duration frequency curve statistical analysis and modeling...
Rainfall intensity duration frequency curve statistical analysis and modeling...
Optimizing Gradle Builds - Gradle DPE Tour Berlin 2024
Optimizing Gradle Builds - Gradle DPE Tour Berlin 2024
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...
Automatic Street Light Controller Using Arduino
- 2. AUTOMATIC STREET LIGHT CONTROLLER USING ARDUINO
- 4. INTRODUCTION • IN OUR COUNTRY, THE CORPORATION STREET LIGHT CONSUMES MORE POWER WHEN ROADS ARE DESOLATE. HOWEVER WITH THE INCREASING IMPORTANCE FOR SAVING POWER AND PROPER MAINTENANCE ARE LEADS TO SAVE THE NATURAL RESOURCES FOR THE FUTURE. A SMART STREET LIGHT SYSTEM CAN REDUCE THE POWER OF CORPORATION STREET LIGHT FOR DESOLATE ROADS. • IN OUR PROJECT GIVES THE SOLUTION TO THOSE PROBLEMS. AN AUTOMATIC STREET LIGHT SYSTEM USING SENSORS AND WIRELESS MODULES FOR IMPLEMENT A SYSTEM. THE LDR (LIGHT DEPENDENT RESISTOR) SENSING THE WEATHER CONDITION. • THE SYSTEM CAN IDENTIFY THE BRIGHT OR DARK ENVIRONMENT USING LDR. THE WEATHER IS DARK THE SYSTEM ALLOWS TO ON THE STREET LIGHTS. THE WEATHER IS BRIGHT THE SYSTEM ALLOWS TO OFF THE STREET LIGHTS. SAME THIS LDR OPERATION IS USED TO FIND THE LIGHT FAULT DETECTION AND SEND TO THE CONTROL ROOM USING ESP8266 WI-FI MODULE. • HERE THE INTENSITY OF THE STREET LIGHT TO BE CONTROLLED BY THE CONTROLLER. WHENEVER PIR SENSE THE MOTION OF VEHICLE, THE STREET LIGHT WILL GLOW AS BRIGHT OR NORMAL. OTHERWISE THE STREET LIGHT WILL GLOW AS DIM.
- 5. BLOCK DIAGRAM AND DESCRIPTION Power supply Rectifier Regulator LDR Street light IoT PIR sensor
- 6. BLOCK DIAGRAM : POWER SUPPLY :
- 8. HARDWARE IMPLEMENTATION : LDR MODULE:
- 10. FLOW CHART: Start Read LDR value LDR<5 0 Stop Send the message to the control room A A YES NO
- 11. CODE
- 12. SIMULATION
- 15. THE END