This document discusses static CMOS logic design. It can be made pipelined by inserting latches between combinational logic stages. Static CMOS uses complementary signals and requires both NMOS and PMOS transistors. The propagation delay increases with higher fan-in because of increased capacitive loading on internal nodes. Other logic styles discussed include pseudo-NMOS, dynamic CMOS, pass transistor logic, and switch logic.
Part of Lecture series on EE321N, Power Electronics-I delivered by me during Fifth Semester of B.Tech. Electrical Engg., 2012
Z H College of Engg. & Technology, Aligarh Muslim University, Aligarh
Please comment and feel free to ask anything related. Thanks!
The Quadrature Phase Shift Keying QPSK is a variation of BPSK, and it is also a Double Side Band Suppressed Carrier DSBSC modulation scheme, which sends two bits of digital information at a time, called as bigits.
Instead of the conversion of digital bits into a series of digital stream, it converts them into bit pairs. This decreases the data bit rate to half, which allows space for the other users.
QPSK (Quadrature Phase Shift Keying) is type of phase shift keying. Unlike BPSK which is a DSBCS modulation scheme with digital information for the message, QPSK is also a DSBCS modulation scheme but it sends two bits of digital information a time (without the use of another carrier frequency).
The amount of radio frequency spectrum required to transmit QPSK reliably is half that required for BPSK signals, which in turn makes room for more users on the channel.
Part of Lecture series on EE321N, Power Electronics-I delivered by me during Fifth Semester of B.Tech. Electrical Engg., 2012
Z H College of Engg. & Technology, Aligarh Muslim University, Aligarh
Please comment and feel free to ask anything related. Thanks!
The Quadrature Phase Shift Keying QPSK is a variation of BPSK, and it is also a Double Side Band Suppressed Carrier DSBSC modulation scheme, which sends two bits of digital information at a time, called as bigits.
Instead of the conversion of digital bits into a series of digital stream, it converts them into bit pairs. This decreases the data bit rate to half, which allows space for the other users.
QPSK (Quadrature Phase Shift Keying) is type of phase shift keying. Unlike BPSK which is a DSBCS modulation scheme with digital information for the message, QPSK is also a DSBCS modulation scheme but it sends two bits of digital information a time (without the use of another carrier frequency).
The amount of radio frequency spectrum required to transmit QPSK reliably is half that required for BPSK signals, which in turn makes room for more users on the channel.
In this video, I will explain what is QAM modulation and what is 16QAM.
QAM Stands for Quadrature Amplitude Modulation. QAM is both an analog and a digital modulation method. But here, we are only talking about QAM as a digital modulation.
Quadrature means that two carrier waves are being used, one sine wave and one cosine wave. These two waves are out of phase with each other by 90°, this is called quadrature.
At the receiving end, the sine and cosine wave can be decoded independently, this means that by using both a sine wave and a cosine wave, the communication channel's capacity is doubled comparing to using only one sine or one cosine wave. That is why quadrature is such a popular technique for digital modulation.
QAM modulation is a combination of Amplitude Shift Keying and Phase Shift Keying, both carrier wave is modulated by changing both its amplitude and phase. As shown in this 8QAM waveform, the top is the sine wave carrier, for bit 000, the sin wave has a phase shift of 0°, and an amplitude of 2. While for bit 110, the phase shift is 180°, and the amplitude now is 1. So both phase and amplitude are changed.
In 16QAM, the input binary data is combined into groups of 4 bits called QUADBITS.
As shown in this picture, the I and I' bits are sent to the sine wave modulation path, and the Q and Q' bits are sent to the cosine wave path. Since the bits are split and sent in parallel, so the symbol rate has been reduced to a quarter of the input binary bit rate. If the input binary data rate is 100 Gbps, then the symbol rate is reduced to only 25 Gbaud/second. This is the reason why 16QAM is under hot research for 100Gbps fiber optic communication.
The I and Q bits control the carrier wave's phase shift, if the bit is 0, then the phase shift is 180°, if the bit is 1, then the phase shift is 0°.
The I' and Q' bits control the carrier wave's amplitude, if bit is 0, then the amplitude is 0.22 volt, if the bit is 1, then the amplitude is 0.821 volt.
So each pair of bits has 4 different outputs. Then they are added up at the linear summer. 4X4 is 16, so there is a total of 16 different combinations at the output, that is why this is called 16QAM.
This illustration shows an example of how the QUADBIT 0000 is modulated onto the carrier waves.
Here I and I' is 00, so the output is -0.22 Volt at the 2-to-4-level converter, when timed with the sine wave carrier, we get -0.22sin(2πfct), here fc is the carrier wave's frequency. QQ' is also 00, so the other carrier wave output is -0.22cos(2πfct).
Here is the proof that quadbit 0000 is modulated as a sine wave with an amplitude of 0.311volt and a phase shift of -135°. You can now pause for a moment to study the proof.
This list shows the 16QAM modulation output with different amplitude and phase change for all 16 quadbits. On the right side is the constellation diagram which shows the positions of these quadbits on a I-Q diagram.
You can visit FO4SALE.com f
Part of Lecture series on EE321N, Power Electronics-I delivered by me during Fifth Semester of B.Tech. Electrical Engg., 2012
Z H College of Engg. & Technology, Aligarh Muslim University, Aligarh
Please comment and feel free to ask anything related. Thanks!
We are providing training on IEEE 2016-17 projects for Ph.D Scalars, M.Tech, B.E, MCA, BCA and Diploma students for
all branches for their academic projects.
For more details call us or watsapp us @ 7676768124 0r 9545252155
Email your base papers to "adritsolutions@gmail.co.in"
We are providing IEEE projects on
1) Cloud Computing, Data Mining, BigData Projects Using JAva
2) Image Processing and Video Procesing (MATLAB) , Signal Processing
3) NS2 (Wireless Sensor, MANET, VANET)
4) ANDRIOD APPS
5) JAVA, JEE, J2EE, J2ME
6) Mechanical Design projects
7) Embedded Systems and IoT Projects
8) VLSI- Verilog Projects (ModelSim and Xilinx using FPGA)
For More details Please Visit us at
Adrit Solutions
Near Maruthi Mandir
#42/5, 18th Cross, 21st Main
Vijaynagar
Bangalore.
In this video, I will explain what is QAM modulation and what is 16QAM.
QAM Stands for Quadrature Amplitude Modulation. QAM is both an analog and a digital modulation method. But here, we are only talking about QAM as a digital modulation.
Quadrature means that two carrier waves are being used, one sine wave and one cosine wave. These two waves are out of phase with each other by 90°, this is called quadrature.
At the receiving end, the sine and cosine wave can be decoded independently, this means that by using both a sine wave and a cosine wave, the communication channel's capacity is doubled comparing to using only one sine or one cosine wave. That is why quadrature is such a popular technique for digital modulation.
QAM modulation is a combination of Amplitude Shift Keying and Phase Shift Keying, both carrier wave is modulated by changing both its amplitude and phase. As shown in this 8QAM waveform, the top is the sine wave carrier, for bit 000, the sin wave has a phase shift of 0°, and an amplitude of 2. While for bit 110, the phase shift is 180°, and the amplitude now is 1. So both phase and amplitude are changed.
In 16QAM, the input binary data is combined into groups of 4 bits called QUADBITS.
As shown in this picture, the I and I' bits are sent to the sine wave modulation path, and the Q and Q' bits are sent to the cosine wave path. Since the bits are split and sent in parallel, so the symbol rate has been reduced to a quarter of the input binary bit rate. If the input binary data rate is 100 Gbps, then the symbol rate is reduced to only 25 Gbaud/second. This is the reason why 16QAM is under hot research for 100Gbps fiber optic communication.
The I and Q bits control the carrier wave's phase shift, if the bit is 0, then the phase shift is 180°, if the bit is 1, then the phase shift is 0°.
The I' and Q' bits control the carrier wave's amplitude, if bit is 0, then the amplitude is 0.22 volt, if the bit is 1, then the amplitude is 0.821 volt.
So each pair of bits has 4 different outputs. Then they are added up at the linear summer. 4X4 is 16, so there is a total of 16 different combinations at the output, that is why this is called 16QAM.
This illustration shows an example of how the QUADBIT 0000 is modulated onto the carrier waves.
Here I and I' is 00, so the output is -0.22 Volt at the 2-to-4-level converter, when timed with the sine wave carrier, we get -0.22sin(2πfct), here fc is the carrier wave's frequency. QQ' is also 00, so the other carrier wave output is -0.22cos(2πfct).
Here is the proof that quadbit 0000 is modulated as a sine wave with an amplitude of 0.311volt and a phase shift of -135°. You can now pause for a moment to study the proof.
This list shows the 16QAM modulation output with different amplitude and phase change for all 16 quadbits. On the right side is the constellation diagram which shows the positions of these quadbits on a I-Q diagram.
You can visit FO4SALE.com f
Part of Lecture series on EE321N, Power Electronics-I delivered by me during Fifth Semester of B.Tech. Electrical Engg., 2012
Z H College of Engg. & Technology, Aligarh Muslim University, Aligarh
Please comment and feel free to ask anything related. Thanks!
We are providing training on IEEE 2016-17 projects for Ph.D Scalars, M.Tech, B.E, MCA, BCA and Diploma students for
all branches for their academic projects.
For more details call us or watsapp us @ 7676768124 0r 9545252155
Email your base papers to "adritsolutions@gmail.co.in"
We are providing IEEE projects on
1) Cloud Computing, Data Mining, BigData Projects Using JAva
2) Image Processing and Video Procesing (MATLAB) , Signal Processing
3) NS2 (Wireless Sensor, MANET, VANET)
4) ANDRIOD APPS
5) JAVA, JEE, J2EE, J2ME
6) Mechanical Design projects
7) Embedded Systems and IoT Projects
8) VLSI- Verilog Projects (ModelSim and Xilinx using FPGA)
For More details Please Visit us at
Adrit Solutions
Near Maruthi Mandir
#42/5, 18th Cross, 21st Main
Vijaynagar
Bangalore.
In digital logic and computing, a counter is a device which stores the number of times a particular event or process has occurred, often in relationship to a clock signal. CMOS devices are designed for high noise immunity and low static power consumption. CMOS accomplishes current reduction by complementing every nMOSFET with a pMOSFET and connecting both gates and both drains together. A high voltage on the gates will cause the nMOSFET to conduct and the pMOSFET to not conduct, while a low voltage on the gate causes the reverse. This arrangement greatly reduces power consumption and heat generation .Finally we proposed counter using SRAM model, provides the best resolution, high output current and good output-input current linearity.
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
CFD Simulation of By-pass Flow in a HRSG module by R&R Consult.pptxR&R Consult
CFD analysis is incredibly effective at solving mysteries and improving the performance of complex systems!
Here's a great example: At a large natural gas-fired power plant, where they use waste heat to generate steam and energy, they were puzzled that their boiler wasn't producing as much steam as expected.
R&R and Tetra Engineering Group Inc. were asked to solve the issue with reduced steam production.
An inspection had shown that a significant amount of hot flue gas was bypassing the boiler tubes, where the heat was supposed to be transferred.
R&R Consult conducted a CFD analysis, which revealed that 6.3% of the flue gas was bypassing the boiler tubes without transferring heat. The analysis also showed that the flue gas was instead being directed along the sides of the boiler and between the modules that were supposed to capture the heat. This was the cause of the reduced performance.
Based on our results, Tetra Engineering installed covering plates to reduce the bypass flow. This improved the boiler's performance and increased electricity production.
It is always satisfying when we can help solve complex challenges like this. Do your systems also need a check-up or optimization? Give us a call!
Work done in cooperation with James Malloy and David Moelling from Tetra Engineering.
More examples of our work https://www.r-r-consult.dk/en/cases-en/
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
block diagram and signal flow graph representation
Advd lecture 09 - microsoft power point - lec-9-inverte-rpart4 [compatibility mode]
1. Combinational logic
STATIC CMOS GATES
no clock design
Can Be Made pipelined By Inserting Latches
in between
Combinational logic
STATIC CMOS GATES
no clock design
Can Be Made pipelined By Inserting Latches
in between
10. Drawback of static cmos
• 2N devices required
• Prop delay inc with increase in fanin
because of inc in Cint, large series chain
11. Uniform transistor sizing
• For the gate, Find equivalent inverter
model
• Find the required transistor w/L
• Hence estimate w/L of each transistor
• For the gate, Find equivalent inverter
model
• Find the required transistor w/L
• Hence estimate w/L of each transistor
21. Power reduction- Time multiplexing of
resources—area reduces, activity increases
Very low switching activity Very high switching activity as bus
toggles between 0 and 1