The Top 10 Mistakes Made in Electrical Workplace Safety is a presentation from Magid Glove & Safety breaks down the 10 most common mistakes made in electrical workplace safety and provides safety tips and product recommendations that will help keep your workers safe and protected.
The electrical arc creates a pressure wave. The incident energy is the energy of this arc-flash coming into contact with a surface. Essentially an electric arc creates a radiation burn which accounts for the internal burns a person can receive when exposed to an electrical arc flash.
Webinar - Electrical Arc Flash Hazards - Is your company in compliance?Leonardo ENERGY
This course is designed to equip the electrical consultant, system designer or any other professional responsible for designing or modernizing commercial and industrial electrical power distribution systems with the fundamentals of the Arc Flash Energy phenomenon.
The electrical arc creates a pressure wave. The incident energy is the energy of this arc-flash coming into contact with a surface. Essentially an electric arc creates a radiation burn which accounts for the internal burns a person can receive when exposed to an electrical arc flash.
Webinar - Electrical Arc Flash Hazards - Is your company in compliance?Leonardo ENERGY
This course is designed to equip the electrical consultant, system designer or any other professional responsible for designing or modernizing commercial and industrial electrical power distribution systems with the fundamentals of the Arc Flash Energy phenomenon.
This training presentation covers the basic on arc flash and other electrical hazards, including the effects of an arc flash incident and how to determine shock and flash protection boundaries for a safe workplace
1. What is arc flash
2. OSHA, NFPA 70E
3. Codes and standards
4. Protective clothing and equipment
5. Prevention
An arc flash (or arc blast) is a type of electrical explosion that results from a low impedance connection to ground or another voltage phase in an electrical system
Even without electrocution, death or dismemberment may occur through an intense arc blast, up to 35,000 F deg, and force up to 2100 psi from the intense heat rapidly expanding the air, copper & particles creating a shockwave blast. Droplets of molten metal and shrapnel can penetrate the body.
Electrical Commissioning and Arc-Flash Safety presentationMichael Luffred
Electrical Commissioning and Arc Flash Safety training presentation given November 21, 2013. Mike Luffred presented this information as a technical seminar for the National Capital Chapter region (PA/NJ/DE/VA/MD/DC) of the Building Commissioning Association. The presentation was given at the Eaton Experience Center in Warrendale, PA to help commissioning engineers understand the importance of arc flash safety in the industry.
An arc blast or flash can occur when workers service electrical power, transmission, and distribution systems using high voltage. It is important to understand the OSHA, NFPA, IEEE and NEC requirements as well as the hierarchy of controls to reduce the risk. Understanding how to calculate a flash analysis to determine the protection boundaries, train workers on the hazards of high voltage electricity and use of personal protective equipment and clothing, and using the right tools for the job are all important steps. Learn more about arc blast/flash in this presentation. If you need advice or help with electrical safety, contact our staff of CSPs at The Windsor Consulting Group, Inc. We have past performance working with contractors near powerlines and underground utilities.
Arc flash incidents can be costly in terms of personnel injury and equipment repair/replacement. This presentation provides an overview of the NFPA 70E 2012 Standard for Electrical Safety in the Workplace and the requirements of the standards, which are intended to better protect electrical workers from injury when they work on energized electrical equipment. This includes all aspects of facility and employer responsibilities for compliance to the NFPA 70E standards, as well as the current status of OSHA enforcement of these standards. Copyright AIST Reprinted with Permission.
Practical Arc Flash Protection for Electrical Safety ProfessionalsLiving Online
Electrical safety is an important issue for those working on electrical facilities in utility networks and large industrial installations. A number of serious accidents including fatalities occur every year due to accidents involving electricity resulting in huge financial losses and wasted man-hours. Arc flashes in electrical equipment are now considered one of the major causes of electrical accidents even surpassing the well known hazards of electric shock. Avoiding arc flash incidents and the resulting injuries is one of major challenges today facing electrical workers and requires adequate attention in the stages of system planning, design, installation, operation and maintenance.
Injuries due to arc flash can depend on many factors, one of which is the incident thermal energy on a worker exposed to a flash. Today, a considerable body of knowledge exists as a result of research efforts and is available to designers and maintenance engineers in the form of standards such as IEEE 1584 and NFPA 70E. This workshop will detail the basis of this approach and also about the major advances that have been made in the area of PPE made of FR fabrics and rated for different levels of thermal exposure.
Prevention however still remains the best form of protection and switchgear manufacturers have made considerable design advances to ensure that the effect of arc flash incidents is contained within the enclosure of switchgear (often called arc flash resistant switchgear) and methods of testing such switchgear have also evolved simultaneously. Another important factor is the approach to avoid arc incidents within the switchgear by proper design and maintenance and techniques to reduce the severity of the flash should such incidents occur.
These would form the key focus areas of this workshop.
MORE INFORMATION: http://www.idc-online.com/content/practical-arc-flash-protection-electrical-safety-professionals-22
Arc flash typically occurs when the electrical insulation or isolation between live conductors is severed or can no longer withstand the applied voltage. Near the high power electrical equipment, the short-circuit power available is high and consequently so is the energy associated with the electrical arc in case of a fault.
In Europe, regulation and standardization are mainly aimed at protecting workers against the risks of direct contact during work and interventions on and near electrical installations. The risks in the case of electric arc and the means to prevent them are mentioned but not developed.The effects of the electric arc:
The electric arc produces intense light and heat, high noise, high overpressure
Heat and splashes of molten metal can cause lethal burns
Noise can lead to permanent or temporary hearing loss, a flash of vision disorders
The overpressure can open and project the doors of electrical cabinets or cause falls during work at height
In addition to personal injury, an arc flash can result in serious damage to electrical equipment. which can cause disruption to electrical systems in manufacturing and process industry environments or tertiary buildings. The cost of downtime can be considerable. elec calc™ Arc Flash module provides the professionals of the electrical industry with a fundamental tool in the sector, as the user will be able to develop its safety analysis in the vicinity of switchboards and panels. By design, elec calc™ has almost all the data allowing the calculation of the figures of the arc flash, from which the user will be able to elaborate his security analysis near the tables and boxes.
Many workers working on energised equipment are injured and/or killed each year. Several of these casualties are a result of arc flash.
Arc Flash is considered as one of the most destructive and dangerous instances when dealing with electrical wirings. A single occurrence can destroy metals and it has the ability to kill a person if not protected by Arc Flash Clothing. An arc flash can create an arc blast that can shatter anything because it is as hot as the as surface of the sun. This kind of heat can destroy metals instantly and completely burn a body beyond recognition.
Arc Flash ProtectionSerious injuries are caused by the arc flash:
Burns
Respiratory system damage
Hearing damage
Skin penetration from flying debris
Eye and face injuries
An arc flash may happen instantly and if the worker does not have the correct protection, they will already be dead when the arc flash hits them.
The use of Arc Flash Protective Equipment will lessen the damages caused by an arc flash because all of these equipments are solely made to withstand the heat.
Typical Arc Flash Clothing Applications
Working on electrical systems and switchrooms at 500 volts, live testing and proving dead on electrical systems, fitting and removal of LV-HV earths on electrical systems, working on panels/control circuits with exposed energised conductors, removal of bolted covers from energised electrical equipment, racking in/out of switchgear, racking in/out of starters and control gear, live testing and proving dead on electrical systems 11-33kV - T&D UK stock a broad range of Arc Flash Clothing and PPE.
Safety is the number one priority of everyone while at work. We have collected the top ten safety tips you need to know to safe at work! #NationalSafetyMonth
This training presentation covers the basic on arc flash and other electrical hazards, including the effects of an arc flash incident and how to determine shock and flash protection boundaries for a safe workplace
1. What is arc flash
2. OSHA, NFPA 70E
3. Codes and standards
4. Protective clothing and equipment
5. Prevention
An arc flash (or arc blast) is a type of electrical explosion that results from a low impedance connection to ground or another voltage phase in an electrical system
Even without electrocution, death or dismemberment may occur through an intense arc blast, up to 35,000 F deg, and force up to 2100 psi from the intense heat rapidly expanding the air, copper & particles creating a shockwave blast. Droplets of molten metal and shrapnel can penetrate the body.
Electrical Commissioning and Arc-Flash Safety presentationMichael Luffred
Electrical Commissioning and Arc Flash Safety training presentation given November 21, 2013. Mike Luffred presented this information as a technical seminar for the National Capital Chapter region (PA/NJ/DE/VA/MD/DC) of the Building Commissioning Association. The presentation was given at the Eaton Experience Center in Warrendale, PA to help commissioning engineers understand the importance of arc flash safety in the industry.
An arc blast or flash can occur when workers service electrical power, transmission, and distribution systems using high voltage. It is important to understand the OSHA, NFPA, IEEE and NEC requirements as well as the hierarchy of controls to reduce the risk. Understanding how to calculate a flash analysis to determine the protection boundaries, train workers on the hazards of high voltage electricity and use of personal protective equipment and clothing, and using the right tools for the job are all important steps. Learn more about arc blast/flash in this presentation. If you need advice or help with electrical safety, contact our staff of CSPs at The Windsor Consulting Group, Inc. We have past performance working with contractors near powerlines and underground utilities.
Arc flash incidents can be costly in terms of personnel injury and equipment repair/replacement. This presentation provides an overview of the NFPA 70E 2012 Standard for Electrical Safety in the Workplace and the requirements of the standards, which are intended to better protect electrical workers from injury when they work on energized electrical equipment. This includes all aspects of facility and employer responsibilities for compliance to the NFPA 70E standards, as well as the current status of OSHA enforcement of these standards. Copyright AIST Reprinted with Permission.
Practical Arc Flash Protection for Electrical Safety ProfessionalsLiving Online
Electrical safety is an important issue for those working on electrical facilities in utility networks and large industrial installations. A number of serious accidents including fatalities occur every year due to accidents involving electricity resulting in huge financial losses and wasted man-hours. Arc flashes in electrical equipment are now considered one of the major causes of electrical accidents even surpassing the well known hazards of electric shock. Avoiding arc flash incidents and the resulting injuries is one of major challenges today facing electrical workers and requires adequate attention in the stages of system planning, design, installation, operation and maintenance.
Injuries due to arc flash can depend on many factors, one of which is the incident thermal energy on a worker exposed to a flash. Today, a considerable body of knowledge exists as a result of research efforts and is available to designers and maintenance engineers in the form of standards such as IEEE 1584 and NFPA 70E. This workshop will detail the basis of this approach and also about the major advances that have been made in the area of PPE made of FR fabrics and rated for different levels of thermal exposure.
Prevention however still remains the best form of protection and switchgear manufacturers have made considerable design advances to ensure that the effect of arc flash incidents is contained within the enclosure of switchgear (often called arc flash resistant switchgear) and methods of testing such switchgear have also evolved simultaneously. Another important factor is the approach to avoid arc incidents within the switchgear by proper design and maintenance and techniques to reduce the severity of the flash should such incidents occur.
These would form the key focus areas of this workshop.
MORE INFORMATION: http://www.idc-online.com/content/practical-arc-flash-protection-electrical-safety-professionals-22
Arc flash typically occurs when the electrical insulation or isolation between live conductors is severed or can no longer withstand the applied voltage. Near the high power electrical equipment, the short-circuit power available is high and consequently so is the energy associated with the electrical arc in case of a fault.
In Europe, regulation and standardization are mainly aimed at protecting workers against the risks of direct contact during work and interventions on and near electrical installations. The risks in the case of electric arc and the means to prevent them are mentioned but not developed.The effects of the electric arc:
The electric arc produces intense light and heat, high noise, high overpressure
Heat and splashes of molten metal can cause lethal burns
Noise can lead to permanent or temporary hearing loss, a flash of vision disorders
The overpressure can open and project the doors of electrical cabinets or cause falls during work at height
In addition to personal injury, an arc flash can result in serious damage to electrical equipment. which can cause disruption to electrical systems in manufacturing and process industry environments or tertiary buildings. The cost of downtime can be considerable. elec calc™ Arc Flash module provides the professionals of the electrical industry with a fundamental tool in the sector, as the user will be able to develop its safety analysis in the vicinity of switchboards and panels. By design, elec calc™ has almost all the data allowing the calculation of the figures of the arc flash, from which the user will be able to elaborate his security analysis near the tables and boxes.
Many workers working on energised equipment are injured and/or killed each year. Several of these casualties are a result of arc flash.
Arc Flash is considered as one of the most destructive and dangerous instances when dealing with electrical wirings. A single occurrence can destroy metals and it has the ability to kill a person if not protected by Arc Flash Clothing. An arc flash can create an arc blast that can shatter anything because it is as hot as the as surface of the sun. This kind of heat can destroy metals instantly and completely burn a body beyond recognition.
Arc Flash ProtectionSerious injuries are caused by the arc flash:
Burns
Respiratory system damage
Hearing damage
Skin penetration from flying debris
Eye and face injuries
An arc flash may happen instantly and if the worker does not have the correct protection, they will already be dead when the arc flash hits them.
The use of Arc Flash Protective Equipment will lessen the damages caused by an arc flash because all of these equipments are solely made to withstand the heat.
Typical Arc Flash Clothing Applications
Working on electrical systems and switchrooms at 500 volts, live testing and proving dead on electrical systems, fitting and removal of LV-HV earths on electrical systems, working on panels/control circuits with exposed energised conductors, removal of bolted covers from energised electrical equipment, racking in/out of switchgear, racking in/out of starters and control gear, live testing and proving dead on electrical systems 11-33kV - T&D UK stock a broad range of Arc Flash Clothing and PPE.
Safety is the number one priority of everyone while at work. We have collected the top ten safety tips you need to know to safe at work! #NationalSafetyMonth
Getting your PPE Facts Right - 5 Facts and 5 MythsKristy Thornton
Ensure you're protecting yourself and your workers with 'Getting your PPE Facts Right - 5 Facts and 5 Myths'
Kristy Thornton of Thiess Services entry in the British Occupational Hygiene Society and 3M competition to attend the IOHA 2015 conference.
#IOHA2015 #3Mcompetition
@BOHSworld
5 Myths 5 Facts About Personal Protective Equipment (PPE)vogelk
Getting your PPE Facts right - 5 facts and 5 myths. A PowerPoint presentation aimed at dispelling 5 falsely held beliefs about Personal Protective Equipment (PPE)
Starting Off On The Right Foot In Your New JobSocialcast
Being new to the workforce can be an intensive experience. However, there are strategies that can help you rise above the bar, and excel in any industry. Hard word really does pay off.
A slide presentation from Bryan Evans presented at the April 8, 2013 NACE/Pipeliners Joint Meeting in Atlanta, GA. The presentation dealt with the phenomenon of AC electricity running through high voltage lines potentially corroding nearby underground pipelines--and how to mitigate potential problems.
The proper use of personal protective equipment (PPE) is a critical component of any electrical safety program, and yet proper PPE use often is overlooked, diminished, or simply disregarded by electrical workers in manufacturing. Plant Engineering will present a Webcast on December 5th at 1 p.m. CT that will discuss the importance of PPE to mitigate arc flash dangers and other electrical safety issues.
Electrical Safety is a concern in almost every organizations. The risks related to electrical safety are often managed in an isolated way.
This presentation will help organisations to manage Electrical Safety risks in a more structured fashion.
CompTIA exam study guide presentations by instructor Brian Ferrill, PACE-IT (Progressive, Accelerated Certifications for Employment in Information Technology)
"Funded by the Department of Labor, Employment and Training Administration, Grant #TC-23745-12-60-A-53"
Learn more about the PACE-IT Online program: www.edcc.edu/pace-it
Personal Protective Equipment (PPE) is any safety equipment workers wear to prevent injury in the workplace when engineering and administrative controls fail to eliminate the hazard.
basics_of_ppe_training.ppt ppe componentsNitika588942
specialized clothing or equipment worn by an employee for protection against infectious materials” Types of PPE Used in Healthcare Settings
Gloves – protect hands
Gowns/aprons – protect skin and/or clothing
Masks and respirators– protect mouth/nose
Respirators – protect respiratory tract from airborne infectious agents.
Types of PPE Used in Healthcare Settings-Goggles – protect eyes
Face shields – protect face, mouth, nose, and eyes
Key Points About PPE-Don before contact with the patient, generally before entering the room
Use carefully – don’t spread contamination
Remove and discard carefully, either at the doorway or immediately outside patient room; remove respirator outside room
Immediately perform hand hygiene How to Safely Use PPE-Keep gloved hands away from face
Avoid touching or adjusting other PPE
Remove gloves if they become torn; perform hand hygiene before donning new gloves
Limit surfaces and items touched. Contaminated” and “Clean” Areas of PPE-Contaminated – outside front
Areas of PPE that have or are likely to have been in contact with body sites, materials, or environmental surfaces where the infectious organism may reside
Clean – inside, outside back, ties on head and back
Areas of PPE that are not likely to have been in contact with the infectious organism
Sequence for Removing PPE-Gloves
Face shield or goggles
Gown
Mask or respirator
Where to Remove PPE-At doorway, before leaving patient room or in anteroom*
Remove respirator outside room, after door has been closed*
Standard Precautions-Previously called Universal Precautions
Assumes blood and body fluid of ANY patient could be infectious
Recommends PPE and other infection control practices to prevent transmission in any healthcare setting
Decisions about PPE use determined by type of clinical interaction with patient
Standard Precautions for PPE-Mask and goggles or a face shield – Use during patient care activities likely to generate splashes or sprays of blood, body fluids, secretions, or excretionsMask and goggles or a face shield – Use during patient care activities likely to generate splashes or sprays of blood, body fluids, secretions, or excretions
Mask and goggles or a face shield – Use during patient care activities likely to generate splashes or sprays of blood, body fluids, secretions, or excretions
Mask and goggles or a face shield – Use during patient care activities likely to generate splashes or sprays of blood, body fluids, secretions, or excretions
Mask and goggles or a face shield – Use during patient care activities likely to generate splashes or sprays of blood, body fluids, secretions, or excretions
Mask and goggles or a face shield – Use during patient care activities likely to generate splashes or sprays of blood, body fluids, secretions, or excretions
Mask and goggles or a face shield – Use during patient care activities likely to generate splashes or sprays of blood, body fluids, secretions, or excretions
Mask and goggles or a face shield – Use
Is your facility currently an AED program? Each year 382,500 people experience EMS-assessed out-of-hospital non-traumatic sudden cardiac arrest and nine out of 10 victims die. In this Magid Glove & Safety presentation, sponsored by Zoll, Magid explains why the need for an AED program in the workplace is so important and how you can quickly implement and manage one.
Noise-induced hearing loss is the most common permanent and preventable occupationalinjury in the world. In many countries, excessive noise is the biggest compensable occupational hazard. Magid Glove & Safety and Honeywell have teamed up to present you with the newest innovations and trends in hearing conservation so you can better protect yourself and/or your workers.
In 2008 there were over 2 million visits to emergency rooms due to injuries caused by “cutting or piercing instruments or objects”. 18% of these injuries were to the upper extremities – hand, finger, wrist, and arm.
This presentation helps you find the right solution and identifies the major role PPE plays, so you can "cut" costs and keep your workers safe.
Employers have the responsibility to provide a place of employment free from recognized hazards. This Magid presentation provides you with multiple protective clothing options for industrial workers that will help keep your employees safe, productive and protected.
Magid - How to Select Chemical Resistant GlovesMagid
The science in choosing the right chemical resistant glove can be tricky. This Magid presentation guides you through how to choose the right glove for your industrial and non-industrial applications and needs.
This Magid Glove & Safety presentation answers the top 10 questions in personal protection equipment (PPE) vending.
Implementing a PPE vending program can seem a little daunting at first. Thankfully, Magid’s expertise in providing low-cost PPE solutions through innovative technology and distribution can help tailor a unique vending program to the specific needs and budget of any facility.
This presentation by Magid Glove & Safety and 3M highlights some of the top products available for head and eye protection. It shows the advances made in eye and head safety, the common work hazards employees face and tips on keeping workers safe.
There are 751 deaths a year in the construction industry. Falls account for 35% of those fatalities. This presentation provides insights, safety tips and pointers on how to select the proper harnesses that will help protect your workers from deadly falls.
Workers often show up to work already dehydrated and heat symptoms are typically blamed on other health problems such as diabetes or hypertension. This presentation from Magid provides tips to keeping your workers safe, hydrated and their muscles moving when the heat is on.
An average of 92 workers are killed each year in confined space accidents. Magid Glove and Safety teamed up with MSA to create this presentation in effort to help reduce that number by informing you of these hazards and providing you simple solutions to better test your work environment.
New Directions in Targeted Therapeutic Approaches for Older Adults With Mantl...i3 Health
i3 Health is pleased to make the speaker slides from this activity available for use as a non-accredited self-study or teaching resource.
This slide deck presented by Dr. Kami Maddocks, Professor-Clinical in the Division of Hematology and
Associate Division Director for Ambulatory Operations
The Ohio State University Comprehensive Cancer Center, will provide insight into new directions in targeted therapeutic approaches for older adults with mantle cell lymphoma.
STATEMENT OF NEED
Mantle cell lymphoma (MCL) is a rare, aggressive B-cell non-Hodgkin lymphoma (NHL) accounting for 5% to 7% of all lymphomas. Its prognosis ranges from indolent disease that does not require treatment for years to very aggressive disease, which is associated with poor survival (Silkenstedt et al, 2021). Typically, MCL is diagnosed at advanced stage and in older patients who cannot tolerate intensive therapy (NCCN, 2022). Although recent advances have slightly increased remission rates, recurrence and relapse remain very common, leading to a median overall survival between 3 and 6 years (LLS, 2021). Though there are several effective options, progress is still needed towards establishing an accepted frontline approach for MCL (Castellino et al, 2022). Treatment selection and management of MCL are complicated by the heterogeneity of prognosis, advanced age and comorbidities of patients, and lack of an established standard approach for treatment, making it vital that clinicians be familiar with the latest research and advances in this area. In this activity chaired by Michael Wang, MD, Professor in the Department of Lymphoma & Myeloma at MD Anderson Cancer Center, expert faculty will discuss prognostic factors informing treatment, the promising results of recent trials in new therapeutic approaches, and the implications of treatment resistance in therapeutic selection for MCL.
Target Audience
Hematology/oncology fellows, attending faculty, and other health care professionals involved in the treatment of patients with mantle cell lymphoma (MCL).
Learning Objectives
1.) Identify clinical and biological prognostic factors that can guide treatment decision making for older adults with MCL
2.) Evaluate emerging data on targeted therapeutic approaches for treatment-naive and relapsed/refractory MCL and their applicability to older adults
3.) Assess mechanisms of resistance to targeted therapies for MCL and their implications for treatment selection
Lung Cancer: Artificial Intelligence, Synergetics, Complex System Analysis, S...Oleg Kshivets
RESULTS: Overall life span (LS) was 2252.1±1742.5 days and cumulative 5-year survival (5YS) reached 73.2%, 10 years – 64.8%, 20 years – 42.5%. 513 LCP lived more than 5 years (LS=3124.6±1525.6 days), 148 LCP – more than 10 years (LS=5054.4±1504.1 days).199 LCP died because of LC (LS=562.7±374.5 days). 5YS of LCP after bi/lobectomies was significantly superior in comparison with LCP after pneumonectomies (78.1% vs.63.7%, P=0.00001 by log-rank test). AT significantly improved 5YS (66.3% vs. 34.8%) (P=0.00000 by log-rank test) only for LCP with N1-2. Cox modeling displayed that 5YS of LCP significantly depended on: phase transition (PT) early-invasive LC in terms of synergetics, PT N0—N12, cell ratio factors (ratio between cancer cells- CC and blood cells subpopulations), G1-3, histology, glucose, AT, blood cell circuit, prothrombin index, heparin tolerance, recalcification time (P=0.000-0.038). Neural networks, genetic algorithm selection and bootstrap simulation revealed relationships between 5YS and PT early-invasive LC (rank=1), PT N0—N12 (rank=2), thrombocytes/CC (3), erythrocytes/CC (4), eosinophils/CC (5), healthy cells/CC (6), lymphocytes/CC (7), segmented neutrophils/CC (8), stick neutrophils/CC (9), monocytes/CC (10); leucocytes/CC (11). Correct prediction of 5YS was 100% by neural networks computing (area under ROC curve=1.0; error=0.0).
CONCLUSIONS: 5YS of LCP after radical procedures significantly depended on: 1) PT early-invasive cancer; 2) PT N0--N12; 3) cell ratio factors; 4) blood cell circuit; 5) biochemical factors; 6) hemostasis system; 7) AT; 8) LC characteristics; 9) LC cell dynamics; 10) surgery type: lobectomy/pneumonectomy; 11) anthropometric data. Optimal diagnosis and treatment strategies for LC are: 1) screening and early detection of LC; 2) availability of experienced thoracic surgeons because of complexity of radical procedures; 3) aggressive en block surgery and adequate lymph node dissection for completeness; 4) precise prediction; 5) adjuvant chemoimmunoradiotherapy for LCP with unfavorable prognosis.
Flu Vaccine Alert in Bangalore Karnatakaaddon Scans
As flu season approaches, health officials in Bangalore, Karnataka, are urging residents to get their flu vaccinations. The seasonal flu, while common, can lead to severe health complications, particularly for vulnerable populations such as young children, the elderly, and those with underlying health conditions.
Dr. Vidisha Kumari, a leading epidemiologist in Bangalore, emphasizes the importance of getting vaccinated. "The flu vaccine is our best defense against the influenza virus. It not only protects individuals but also helps prevent the spread of the virus in our communities," he says.
This year, the flu season is expected to coincide with a potential increase in other respiratory illnesses. The Karnataka Health Department has launched an awareness campaign highlighting the significance of flu vaccinations. They have set up multiple vaccination centers across Bangalore, making it convenient for residents to receive their shots.
To encourage widespread vaccination, the government is also collaborating with local schools, workplaces, and community centers to facilitate vaccination drives. Special attention is being given to ensuring that the vaccine is accessible to all, including marginalized communities who may have limited access to healthcare.
Residents are reminded that the flu vaccine is safe and effective. Common side effects are mild and may include soreness at the injection site, mild fever, or muscle aches. These side effects are generally short-lived and far less severe than the flu itself.
Healthcare providers are also stressing the importance of continuing COVID-19 precautions. Wearing masks, practicing good hand hygiene, and maintaining social distancing are still crucial, especially in crowded places.
Protect yourself and your loved ones by getting vaccinated. Together, we can help keep Bangalore healthy and safe this flu season. For more information on vaccination centers and schedules, residents can visit the Karnataka Health Department’s official website or follow their social media pages.
Stay informed, stay safe, and get your flu shot today!
Knee anatomy and clinical tests 2024.pdfvimalpl1234
This includes all relevant anatomy and clinical tests compiled from standard textbooks, Campbell,netter etc..It is comprehensive and best suited for orthopaedicians and orthopaedic residents.
Prix Galien International 2024 Forum ProgramLevi Shapiro
June 20, 2024, Prix Galien International and Jerusalem Ethics Forum in ROME. Detailed agenda including panels:
- ADVANCES IN CARDIOLOGY: A NEW PARADIGM IS COMING
- WOMEN’S HEALTH: FERTILITY PRESERVATION
- WHAT’S NEW IN THE TREATMENT OF INFECTIOUS,
ONCOLOGICAL AND INFLAMMATORY SKIN DISEASES?
- ARTIFICIAL INTELLIGENCE AND ETHICS
- GENE THERAPY
- BEYOND BORDERS: GLOBAL INITIATIVES FOR DEMOCRATIZING LIFE SCIENCE TECHNOLOGIES AND PROMOTING ACCESS TO HEALTHCARE
- ETHICAL CHALLENGES IN LIFE SCIENCES
- Prix Galien International Awards Ceremony
NVBDCP.pptx Nation vector borne disease control programSapna Thakur
NVBDCP was launched in 2003-2004 . Vector-Borne Disease: Disease that results from an infection transmitted to humans and other animals by blood-feeding arthropods, such as mosquitoes, ticks, and fleas. Examples of vector-borne diseases include Dengue fever, West Nile Virus, Lyme disease, and malaria.
Ozempic: Preoperative Management of Patients on GLP-1 Receptor Agonists Saeid Safari
Preoperative Management of Patients on GLP-1 Receptor Agonists like Ozempic and Semiglutide
ASA GUIDELINE
NYSORA Guideline
2 Case Reports of Gastric Ultrasound
These lecture slides, by Dr Sidra Arshad, offer a quick overview of physiological basis of a normal electrocardiogram.
Learning objectives:
1. Define an electrocardiogram (ECG) and electrocardiography
2. Describe how dipoles generated by the heart produce the waveforms of the ECG
3. Describe the components of a normal electrocardiogram of a typical bipolar leads (limb II)
4. Differentiate between intervals and segments
5. Enlist some common indications for obtaining an ECG
Study Resources:
1. Chapter 11, Guyton and Hall Textbook of Medical Physiology, 14th edition
2. Chapter 9, Human Physiology - From Cells to Systems, Lauralee Sherwood, 9th edition
3. Chapter 29, Ganong’s Review of Medical Physiology, 26th edition
4. Electrocardiogram, StatPearls - https://www.ncbi.nlm.nih.gov/books/NBK549803/
5. ECG in Medical Practice by ABM Abdullah, 4th edition
6. ECG Basics, http://www.nataliescasebook.com/tag/e-c-g-basics
HOT NEW PRODUCT! BIG SALES FAST SHIPPING NOW FROM CHINA!! EU KU DB BK substit...GL Anaacs
Contact us if you are interested:
Email / Skype : kefaya1771@gmail.com
Threema: PXHY5PDH
New BATCH Ku !!! MUCH IN DEMAND FAST SALE EVERY BATCH HAPPY GOOD EFFECT BIG BATCH !
Contact me on Threema or skype to start big business!!
Hot-sale products:
NEW HOT EUTYLONE WHITE CRYSTAL!!
5cl-adba precursor (semi finished )
5cl-adba raw materials
ADBB precursor (semi finished )
ADBB raw materials
APVP powder
5fadb/4f-adb
Jwh018 / Jwh210
Eutylone crystal
Protonitazene (hydrochloride) CAS: 119276-01-6
Flubrotizolam CAS: 57801-95-3
Metonitazene CAS: 14680-51-4
Payment terms: Western Union,MoneyGram,Bitcoin or USDT.
Deliver Time: Usually 7-15days
Shipping method: FedEx, TNT, DHL,UPS etc.Our deliveries are 100% safe, fast, reliable and discreet.
Samples will be sent for your evaluation!If you are interested in, please contact me, let's talk details.
We specializes in exporting high quality Research chemical, medical intermediate, Pharmaceutical chemicals and so on. Products are exported to USA, Canada, France, Korea, Japan,Russia, Southeast Asia and other countries.
- Video recording of this lecture in English language: https://youtu.be/lK81BzxMqdo
- Video recording of this lecture in Arabic language: https://youtu.be/Ve4P0COk9OI
- Link to download the book free: https://nephrotube.blogspot.com/p/nephrotube-nephrology-books.html
- Link to NephroTube website: www.NephroTube.com
- Link to NephroTube social media accounts: https://nephrotube.blogspot.com/p/join-nephrotube-on-social-media.html
New Drug Discovery and Development .....NEHA GUPTA
The "New Drug Discovery and Development" process involves the identification, design, testing, and manufacturing of novel pharmaceutical compounds with the aim of introducing new and improved treatments for various medical conditions. This comprehensive endeavor encompasses various stages, including target identification, preclinical studies, clinical trials, regulatory approval, and post-market surveillance. It involves multidisciplinary collaboration among scientists, researchers, clinicians, regulatory experts, and pharmaceutical companies to bring innovative therapies to market and address unmet medical needs.
2. Electrical
Workplace SafetyHow Bad is Bad?
Electrical Hazards – Arc Flash
Watch the disconnect door.
How much
protection
would work in
this arc?
Is over
protection a
good idea?
What works
best here,
PPE or work
practices or a
combination?
3. Electrical
Workplace Safety
Avoiding Mistakes
• Overkill on PPE
“sounds” smart but it has
two negatives
– Sends the wrong
message
– If the workers don’t
believe you they may cut
corners when no one is
watching.
– Watch out for salesmen’s
little lies…
– Better safe than sorry??
– Better safe and right
Match PPE to the hazard
5. Electrical
Workplace Safety
Avoiding Mistakes
• Making the program cheaper or easier
for management or the safety
department or for enforcement may
not be the most cost effective or the
best program.
• A natural program that becomes a
worker’s habit is the most reliable.
• Tends to over protect or not protect at
all.
• Match the kit to the level
– Don’t buy 100 cal kits for everyone.
• Arc rated daily wear is better than a
“coverall program.”
– Darlene’s story
Make the program easy for the worker
Level 2 Kit
10. Electrical
Workplace Safety
Arc-Rated PPE – Clothing
Beware of:
• “FR until washed
or dry cleaned”
• Melting “FR”
• “FR-treated”
acrylics, polyester,
nylon
Got Arc-Rating?
Because of the misuse of the term FR,
NFPA 70E removed the term favoring arc-rated.
14. Electrical
Workplace Safety
• Generic training doesn’t always get to the finer
points.
• Site specific written programs are critical
• Unique hazards must be considered
– FR cotton and 20% body burns from sodium
hypochlorite.
– Aramids and welding spatter.
– Melting polyester in cleanrooms.
• Train + Audit + Knowledgeable Management
= A Great Program
16. Electrical
Workplace Safety
• Assessment will not change the level of
protection but it will change how often you
need to wear it.
• Don’t put off PPE purchases waiting on
assessment
• Daily wear for all electrical workers
• Suits for high level exposures
• Operators work in natural fiber or are rated
gear depending on level of exposure.
Don’t put off PPE purchase but
18. Electrical
Workplace Safety
• Shock is the number one killer of the
electrical hazards.
• More bang for the buck with right PPE than
engineering. Most important engineering is
done by proper installations, maintenance
then equipment upgrades. Engineering out
the arc flash hazard is not always an option.
20. Electrical
Workplace Safety
Avoiding Mistakes
• ASTM F1506
– Hairnets/beardnets
– Cleanroom gear
– Gloves (Proposed separate Standard)
– Disposable FR Wear
• ASTM F1891
– Rainwear
– Chemical gear + Chemical Standard
• ASTM D2413 + D1116
– Shoes (EH or DI or leather, etc.)
• Other Specialty PPE must be evaluated by
the AHJ
Don’t forget specialty gear
22. Electrical
Workplace Safety
Avoiding Mistakes
• The five people you need to do proper hazard
assessment for electrical
– Trouble making electrician
– Nicest electrician
– Smartest electrician
– Electrical Engineer
– Safety Person
The Electrical Safety Team
24. Electrical
Workplace Safety
Three Types of Audits Required
Observations required to
do the following:
• Identifies:
• Demonstrate task
proficiency
• Retraining needs
• Supervisory level
• Part of evaluating Qualified
Persons
Supervisory
Safe Work Practice Inspection
NFPA 70E 110.2(D)(1)(f)
Minimum annual supervisory work practice inspection to
monitor safe work practices
25. Electrical
Workplace Safety
Three Types of Audits Required
Better practice: Separate
from Supervisory Audit.
Observations required to
do the following:
• Prove procedures work
• Identify:
• Procedures that don’t work
• Changes that should be
made
• Retraining needs
Annual Field Work Audit
Site audit looks at the site’s practices and could include
NEC auditing and NFPA/OSHA auditing 110.4 (H)(2)
Best practice: Separate
from Supervisory Audit.
• Year One: Internal by
local safety/electrical
dept.
• Year Two: Cross-
pollinate using another
professional from
another plant or industry
• Year Three: Outside
Audit by competent
auditor
26. Electrical
Workplace Safety
Avoiding Mistakes
• Documented electrical safety
program audit
(not more than every 3 yrs.)
NFPA 70 E 110.3 (H)(1)
• Must reviewed Arc Hazard
Assessment
minimum of every five years.
– Updates required if major
modifications or renovations.
– Required for calculations or if
Tables used.
– Should include audit of labeling.
Electrical Safety Program Audit &
Hazard Assessment Audit
27. Electrical
Workplace Safety
Safety-Related Work Practices
Habit 1 Always verify absence of voltage & use VR gloves &
tools.
Habit 2 Establish worker safety boundaries from shock & arc
flash.
Habit 3 Always wear arc-rated daily wear and a face shield.
Habit 4 Always use GFCI with cord connected tools & extension
cords.
Habit 5 When feasible create an electrically safe work condition.
Habit 6 Plan your jobs, use standards to identify greater
hazards, & adopt controls & PPE to mitigate hazards.
Habit 7 Measure, audit & continuously improve electrical safety
processes.
7 Electrical Safety Habits™
29. Electrical
Workplace Safety
For more information on electrical arc
PPE, for help on selecting the proper arc
PPE or for a custom quote,
Contact your local
Magid Glove & Safety Sales
Representative
1-800-444-8030
www.magidglove.com
30. Electrical
Workplace Safety
*Newsletter is free; charge for DVD.
www.e-hazard.com
Email: questions@e-hazard.com
Phone: (502) 716-7073
For a FREE* copy of Hugh’s
newsletter or information about his
DVD’s:
Text: “DVD” or “Newsletter” with
your e-mail address to:
925-Arc-Wear
(925-272-9327)
Questions?
Want More Information?