This document summarizes research on utilizing waste materials to create more sustainable "green concrete." It discusses how concrete production contributes significantly to greenhouse gas emissions and natural resource depletion. Various studies explored partially replacing cement, coarse aggregates, and fine aggregates in concrete with industrial wastes like fly ash, quarry dust, demolished concrete, ceramic waste, and rice husk ash. Results found that compressive strength was maintained with replacements as high as 30-50% depending on the material. Using these wastes reduces costs, pollution, and natural resource consumption compared to traditional concrete. Overall, the document evaluates green concrete as a promising construction material for more sustainable development.
Utilization of Waste Paper Sludge in Construction IndustrySandeep Jain
This technical note is recapitulation of the work carried out by researchers round the globe on characterization of waste paper sludge based on physical, chemical and mineralogical properties, activation mechanisms, pozzolanic reactivity, reaction kinematics and durability; for its possible utilization in construction industry as supplementary cementitious material, mineral admixture, partial replacement of binders in concrete, raw material for clay brick manufacturing, production of ceramics, soil stabilization in road works, reduction in carbon-dioxide emission etc., in order to en-cash various socio-economic and environmental benefits.
Experimental Study of Partial Replacement of Fine Aggregate with Waste Materi...IJRES Journal
The utilization of industrial and agricultural waste produced by industrial process has been the focus of waste reduction research for economical, environmental and technical reasons. This is because over 300 million tones of industrial waste are being produced per annual by agricultural and industrial process in India. The problem arising from continuous technological and industrial development is the disposal of waste material. If some of the waste materials are found suitable in concrete making not only cost of construction can be cut down, but also safe disposal of waste material can be achieved. The cement of high strength concrete is generally high which often leads to higher shrinkage and greater evaluation of neat of hydration besides increase in cost. A partial substitution of cement by an industrial waste is not only economical but also improves the properties of fresh and hardened concrete and enhance the durability characteristics besides the safe disposal of waste material thereby protecting the environment form pollution This paper deals with partial replacement of fine aggregate with the industrial waste from China Clay industries. The compressive strength, split tensile strength and flexural strength of conventional concrete and fine aggregate replaced concrete are compared and the results are tabulated.
An experimental laboratory study on utilisation of e waste as a partial repla...eSAT Journals
Abstract
The Growth in the Electronics sector has been rapid and this rapid growth is due to continuous upgradation of technology and introduction of new technologies to the market. This has led to one of the fastest growing solid waste in the world, simply called as E-waste. India is the 5th highest e-waste producer in the world. The rapid increase in the construction activity in India, has resulted in huge demand for the aggregates to be used in the concrete. This has led to depletion of natural resources and adverse changes in the environment. This rapid development in the infrastructure sector has led to shortage of natural sand. This paper outlines the experimental work carried for utilisation of e-waste as a partial replacement for the fine aggregates. Strength tests and durability tests are conducted on hardened concrete. Results show that the partial use of E- waste as fine aggregates results in much higher workable and less dense concrete. This study gives an Economic, environment friendly and efficient disposal method for E-waste to be used as a partial replacement to the fine aggregates in concrete.
Keywords: E-waste, M-Sand, Fine aggregate replacement, Concrete, Durabilityetc.
To Study the Properties of Concrete with Partial Replacement of Fine Aggregat...ijtsrd
Natural resources are depleting worldwide while at the same time the generated wastes from the industry are increasing substantially. The sustainable development for construction involves the use of nonconventional and innovative materials, and recycling of waste materials in order to compensate the lack of natural resources and to find alternative ways conserving the environment. So, this paper presents the results of an experimental investigation carried out to evaluate the mechanical properties of concrete mixtures in which fine aggregate sand was replaced with Copper Slag. The fine aggregates sand was replaced with percentages 0 for the control mixture , 10 , 20 , 30 , 40 , 50 , 60 , 80 , and 100 of Copper Slag by weight. Tests were performed for properties of fresh concrete and Hardened Concrete. Compressive strength and Flexural strength were determined at 7, 28 and 56days. The results indicate that workability increases with increase in Copper Slag percentage. Test results indicate significant improvement in the strength properties of plain concrete by the inclusion of up to 80 Copper slag as replacement of fine aggregate sand , and can be effectively used in structural concrete. Also as percentage of Copper Slag increased the density of concrete increased. The workability of concrete increased with increase in percentage of copper slag. Toughness of copper slag is found to be more, which increases the compressive and flexural strength of concrete. Achal Jain | Nitin Thakur "To Study the Properties of Concrete with Partial Replacement of Fine Aggregates through Copper Slag and Coarse Aggregates by Recycled Aggregates" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-6 , October 2019, URL: https://www.ijtsrd.com/papers/ijtsrd28104.pdf Paper URL: https://www.ijtsrd.com/engineering/civil-engineering/28104/to-study-the-properties-of-concrete-with-partial-replacement-of-fine-aggregates-through-copper-slag-and-coarse-aggregates-by-recycled-aggregates/achal-jain
Exploratory study on the use of crushed cockle shell as partial sand replacem...IJRES Journal
The increasing demand for natural river sand supply for the use in construction industry along
with the issue of environmental problem posed by the dumping of cockle shell, a by-product from cockle
business have initiated research towards producing a more environmental friendly concrete. This research
explores the potential use of cockle shell as partial sand replacement in concrete production. Cockle shell used
in this experimental work were crushed to smaller size almost similar to sand before mixed in concrete. A total
of six concrete mixtures were prepared with varying the percentages of cockle shell viz. 0%, 5%, 10%, 15%,
20% and 25%. All the specimens were subjected to continuous water curing. The compressive strength test was
conducted at 28 days in accordance to BS EN 12390. Finding shows that integration of suitable content of
crushed cockle shell of 10% as partial sand replacement able to enhance the compressive strength of concrete.
Adopting crushed cockle shell as partial sand replacement in concrete would reduce natural river sand
consumption as well as reducing the amount of cockle shell disposed as waste.
As concrete is the most abundant material used in the world, it contains aggregate content of around 60 to 70 %. Since aggregate are being used rapidly there has been a scarcity in the avaibility of these materials. This research investigates the effect of partially replacing aggregates by burnt brick bats and lateritic fines in concrete respectively for M25 grade concrete. The incorporation is done for 5%, 10% and 15% of burnt brick bats for coarse aggregate and by talking 15% of lateritic fines as constant for fine aggregate by conducting compressive strength test which gave the optimum value of 15% for natural sand. The compressive strength, split tensile strength and flexural strength was conducted. The results showed density of of the concrete incorporating brick and laterite was lower compared to conventional concrete, the concrete with 5% burnt brick and 15% lateritic soil showed increased strength for 7 days compared to normal concrete but when 28 days test was conducted the strength was similar to conventional concrete. The split tensile and flexural strength of replaced concrete was found to be lower than the nominal concrete.
A research study of Donald u. Bulawin, Cristian Ralph E. Ibahay, and Mabeth L. Arellano. It is all about utilizing the waste bottle caps for concrete mixture. This study aims that by utilizing the waste bottle caps as a partial replacement for coarse aggregates helps in increasing the strength of concrete and in the environmental issues of wastes disposal.
Use of Over-Burnt Bricks as Coarse aggregate in ConcreteEditorIJAERD
In modern construction industry number of materials are used and one of the materials is Brick. Regular
bricks are generally used in buildings or in some other engineering applications. In manufacturing of these bricks, a lot
of waste is produced in the form of over- burnt-bricks. The bricks being near to the fire in the furnace receives a
temperature more heat and eventually shrink and loose its shape, its color becomes reddish. These bricks can’t be used
in construction, directly because of their distorted shape dark color. hose over-burnt brick could be a source of recycled
coarse aggregate. The primary goal of this paper is to assess the suitability of incorporating over-burnt bricks in
concrete, by the partial replacement of natural coarse aggregate (NCA) with overburnt brick aggregate (OBBA) in a
ratio of 20%, 50%, and 100%. Initially, mix proportion of 1:2:4 and w/c of 0.57 was selected. By replacing NCA with
OBBA while using mix proportion of 1:2:4 and w/c of 0.57, the resulting concrete was found non-mixable and nonworkable. Thus, mix was designed (for targeted strength of 4ksi) for all replacement percentages. Slump test was
conducted for each replacement and the results show that by increasing replacement percentage the workability of
concrete decreases. the slump values are in between the range of 3–1.5 inches. For compressive strength the cylindrical
specimens of 6" x 12" were tested at 3, 7, and 28 days. For 20% replacement, the loss in compressive strength is 42.16%
for 3 days and for 7 and 28 days the loss is 46.96% and 61.37% respectively. For 50 % replacement, the loss in strength
for 3, 7 and 28 days is 29.73%, 30.87% and 58.29% respectively. For 100% replacement, the loss in strength for 3, 7 and
28 days is 48.65%, 55.65% and 69.19%.
Utilization of Waste Paper Sludge in Construction IndustrySandeep Jain
This technical note is recapitulation of the work carried out by researchers round the globe on characterization of waste paper sludge based on physical, chemical and mineralogical properties, activation mechanisms, pozzolanic reactivity, reaction kinematics and durability; for its possible utilization in construction industry as supplementary cementitious material, mineral admixture, partial replacement of binders in concrete, raw material for clay brick manufacturing, production of ceramics, soil stabilization in road works, reduction in carbon-dioxide emission etc., in order to en-cash various socio-economic and environmental benefits.
Experimental Study of Partial Replacement of Fine Aggregate with Waste Materi...IJRES Journal
The utilization of industrial and agricultural waste produced by industrial process has been the focus of waste reduction research for economical, environmental and technical reasons. This is because over 300 million tones of industrial waste are being produced per annual by agricultural and industrial process in India. The problem arising from continuous technological and industrial development is the disposal of waste material. If some of the waste materials are found suitable in concrete making not only cost of construction can be cut down, but also safe disposal of waste material can be achieved. The cement of high strength concrete is generally high which often leads to higher shrinkage and greater evaluation of neat of hydration besides increase in cost. A partial substitution of cement by an industrial waste is not only economical but also improves the properties of fresh and hardened concrete and enhance the durability characteristics besides the safe disposal of waste material thereby protecting the environment form pollution This paper deals with partial replacement of fine aggregate with the industrial waste from China Clay industries. The compressive strength, split tensile strength and flexural strength of conventional concrete and fine aggregate replaced concrete are compared and the results are tabulated.
An experimental laboratory study on utilisation of e waste as a partial repla...eSAT Journals
Abstract
The Growth in the Electronics sector has been rapid and this rapid growth is due to continuous upgradation of technology and introduction of new technologies to the market. This has led to one of the fastest growing solid waste in the world, simply called as E-waste. India is the 5th highest e-waste producer in the world. The rapid increase in the construction activity in India, has resulted in huge demand for the aggregates to be used in the concrete. This has led to depletion of natural resources and adverse changes in the environment. This rapid development in the infrastructure sector has led to shortage of natural sand. This paper outlines the experimental work carried for utilisation of e-waste as a partial replacement for the fine aggregates. Strength tests and durability tests are conducted on hardened concrete. Results show that the partial use of E- waste as fine aggregates results in much higher workable and less dense concrete. This study gives an Economic, environment friendly and efficient disposal method for E-waste to be used as a partial replacement to the fine aggregates in concrete.
Keywords: E-waste, M-Sand, Fine aggregate replacement, Concrete, Durabilityetc.
To Study the Properties of Concrete with Partial Replacement of Fine Aggregat...ijtsrd
Natural resources are depleting worldwide while at the same time the generated wastes from the industry are increasing substantially. The sustainable development for construction involves the use of nonconventional and innovative materials, and recycling of waste materials in order to compensate the lack of natural resources and to find alternative ways conserving the environment. So, this paper presents the results of an experimental investigation carried out to evaluate the mechanical properties of concrete mixtures in which fine aggregate sand was replaced with Copper Slag. The fine aggregates sand was replaced with percentages 0 for the control mixture , 10 , 20 , 30 , 40 , 50 , 60 , 80 , and 100 of Copper Slag by weight. Tests were performed for properties of fresh concrete and Hardened Concrete. Compressive strength and Flexural strength were determined at 7, 28 and 56days. The results indicate that workability increases with increase in Copper Slag percentage. Test results indicate significant improvement in the strength properties of plain concrete by the inclusion of up to 80 Copper slag as replacement of fine aggregate sand , and can be effectively used in structural concrete. Also as percentage of Copper Slag increased the density of concrete increased. The workability of concrete increased with increase in percentage of copper slag. Toughness of copper slag is found to be more, which increases the compressive and flexural strength of concrete. Achal Jain | Nitin Thakur "To Study the Properties of Concrete with Partial Replacement of Fine Aggregates through Copper Slag and Coarse Aggregates by Recycled Aggregates" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-6 , October 2019, URL: https://www.ijtsrd.com/papers/ijtsrd28104.pdf Paper URL: https://www.ijtsrd.com/engineering/civil-engineering/28104/to-study-the-properties-of-concrete-with-partial-replacement-of-fine-aggregates-through-copper-slag-and-coarse-aggregates-by-recycled-aggregates/achal-jain
Exploratory study on the use of crushed cockle shell as partial sand replacem...IJRES Journal
The increasing demand for natural river sand supply for the use in construction industry along
with the issue of environmental problem posed by the dumping of cockle shell, a by-product from cockle
business have initiated research towards producing a more environmental friendly concrete. This research
explores the potential use of cockle shell as partial sand replacement in concrete production. Cockle shell used
in this experimental work were crushed to smaller size almost similar to sand before mixed in concrete. A total
of six concrete mixtures were prepared with varying the percentages of cockle shell viz. 0%, 5%, 10%, 15%,
20% and 25%. All the specimens were subjected to continuous water curing. The compressive strength test was
conducted at 28 days in accordance to BS EN 12390. Finding shows that integration of suitable content of
crushed cockle shell of 10% as partial sand replacement able to enhance the compressive strength of concrete.
Adopting crushed cockle shell as partial sand replacement in concrete would reduce natural river sand
consumption as well as reducing the amount of cockle shell disposed as waste.
As concrete is the most abundant material used in the world, it contains aggregate content of around 60 to 70 %. Since aggregate are being used rapidly there has been a scarcity in the avaibility of these materials. This research investigates the effect of partially replacing aggregates by burnt brick bats and lateritic fines in concrete respectively for M25 grade concrete. The incorporation is done for 5%, 10% and 15% of burnt brick bats for coarse aggregate and by talking 15% of lateritic fines as constant for fine aggregate by conducting compressive strength test which gave the optimum value of 15% for natural sand. The compressive strength, split tensile strength and flexural strength was conducted. The results showed density of of the concrete incorporating brick and laterite was lower compared to conventional concrete, the concrete with 5% burnt brick and 15% lateritic soil showed increased strength for 7 days compared to normal concrete but when 28 days test was conducted the strength was similar to conventional concrete. The split tensile and flexural strength of replaced concrete was found to be lower than the nominal concrete.
A research study of Donald u. Bulawin, Cristian Ralph E. Ibahay, and Mabeth L. Arellano. It is all about utilizing the waste bottle caps for concrete mixture. This study aims that by utilizing the waste bottle caps as a partial replacement for coarse aggregates helps in increasing the strength of concrete and in the environmental issues of wastes disposal.
Use of Over-Burnt Bricks as Coarse aggregate in ConcreteEditorIJAERD
In modern construction industry number of materials are used and one of the materials is Brick. Regular
bricks are generally used in buildings or in some other engineering applications. In manufacturing of these bricks, a lot
of waste is produced in the form of over- burnt-bricks. The bricks being near to the fire in the furnace receives a
temperature more heat and eventually shrink and loose its shape, its color becomes reddish. These bricks can’t be used
in construction, directly because of their distorted shape dark color. hose over-burnt brick could be a source of recycled
coarse aggregate. The primary goal of this paper is to assess the suitability of incorporating over-burnt bricks in
concrete, by the partial replacement of natural coarse aggregate (NCA) with overburnt brick aggregate (OBBA) in a
ratio of 20%, 50%, and 100%. Initially, mix proportion of 1:2:4 and w/c of 0.57 was selected. By replacing NCA with
OBBA while using mix proportion of 1:2:4 and w/c of 0.57, the resulting concrete was found non-mixable and nonworkable. Thus, mix was designed (for targeted strength of 4ksi) for all replacement percentages. Slump test was
conducted for each replacement and the results show that by increasing replacement percentage the workability of
concrete decreases. the slump values are in between the range of 3–1.5 inches. For compressive strength the cylindrical
specimens of 6" x 12" were tested at 3, 7, and 28 days. For 20% replacement, the loss in compressive strength is 42.16%
for 3 days and for 7 and 28 days the loss is 46.96% and 61.37% respectively. For 50 % replacement, the loss in strength
for 3, 7 and 28 days is 29.73%, 30.87% and 58.29% respectively. For 100% replacement, the loss in strength for 3, 7 and
28 days is 48.65%, 55.65% and 69.19%.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
Forklift Classes Overview by Intella PartsIntella Parts
Discover the different forklift classes and their specific applications. Learn how to choose the right forklift for your needs to ensure safety, efficiency, and compliance in your operations.
For more technical information, visit our website https://intellaparts.com
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
Quality defects in TMT Bars, Possible causes and Potential Solutions.PrashantGoswami42
Maintaining high-quality standards in the production of TMT bars is crucial for ensuring structural integrity in construction. Addressing common defects through careful monitoring, standardized processes, and advanced technology can significantly improve the quality of TMT bars. Continuous training and adherence to quality control measures will also play a pivotal role in minimizing these defects.
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
COLLEGE BUS MANAGEMENT SYSTEM PROJECT REPORT.pdfKamal Acharya
The College Bus Management system is completely developed by Visual Basic .NET Version. The application is connect with most secured database language MS SQL Server. The application is develop by using best combination of front-end and back-end languages. The application is totally design like flat user interface. This flat user interface is more attractive user interface in 2017. The application is gives more important to the system functionality. The application is to manage the student’s details, driver’s details, bus details, bus route details, bus fees details and more. The application has only one unit for admin. The admin can manage the entire application. The admin can login into the application by using username and password of the admin. The application is develop for big and small colleges. It is more user friendly for non-computer person. Even they can easily learn how to manage the application within hours. The application is more secure by the admin. The system will give an effective output for the VB.Net and SQL Server given as input to the system. The compiled java program given as input to the system, after scanning the program will generate different reports. The application generates the report for users. The admin can view and download the report of the data. The application deliver the excel format reports. Because, excel formatted reports is very easy to understand the income and expense of the college bus. This application is mainly develop for windows operating system users. In 2017, 73% of people enterprises are using windows operating system. So the application will easily install for all the windows operating system users. The application-developed size is very low. The application consumes very low space in disk. Therefore, the user can allocate very minimum local disk space for this application.