The document experimentally investigates the compressive behavior of straw bale bricks. Straw bale bricks were manufactured and then subjected to various tests to determine their properties. The bricks were made from a mixture of straw, clay, lime and water. They were formed into standardized sizes, dried for several days, and then tested for compressive strength, water absorption, impact resistance, and other properties. The results indicate that straw bale bricks have favorable properties such as strength, insulation and cost effectiveness, showing potential as a sustainable and eco-friendly building material.
STUDY ON STRENGTH PROPERTIES OF COCONUT SHELL CONCRETEIAEME Publication
Concrete is the premier construction material around the world and is most widely used in all types of construction works, including infrastructure, low and high-rise buildings, and domestic developments. It is a man-made product, essentially consisting of a mixture of cement, aggregates, water and admixture(s). Inert granular materials such as sand, crushed stone or gravel form the major part of the aggregates. Traditionally aggregates have been readily available at economic prices and of qualities to suit all purposes. But, the continued extensive extraction use of aggregates from natural
resources has been questioned because of the depletion of quality primary aggregates and greater awareness of environmental protection.
Effective utilisation of waste materials on concreteeSAT Journals
Abstract In the world, concrete is material which is produced more than any other man made material. Due to the increasing of population
in the world, a waste material also increases. In those waste materials many are non- degradable materials, they make hazards to
the environment.So, that usage of non degradable waste [1] in concrete will be safe for disposal. This project will give the ideas,
experimental analysis of the recycled aggregates (Coarse Aggregates) and waste glass materials (Fine aggregates) on the
concrete mix. Desired properties of concrete such as strength,, workability,durability can also achieved by adding above
materials in the concrete.
Keywords: Recycled Aggregate, Powder of Waste Glass, Coarse Aggregate-Partial Replacement, Fine Aggregate,
Compression Test, Flexural Strength, Split Tensile Test
STUDY ON STRENGTH PROPERTIES OF COCONUT SHELL CONCRETEIAEME Publication
Concrete is the premier construction material around the world and is most widely used in all types of construction works, including infrastructure, low and high-rise buildings, and domestic developments. It is a man-made product, essentially consisting of a mixture of cement, aggregates, water and admixture(s). Inert granular materials such as sand, crushed stone or gravel form the major part of the aggregates. Traditionally aggregates have been readily available at economic prices and of qualities to suit all purposes. But, the continued extensive extraction use of aggregates from natural
resources has been questioned because of the depletion of quality primary aggregates and greater awareness of environmental protection.
Effective utilisation of waste materials on concreteeSAT Journals
Abstract In the world, concrete is material which is produced more than any other man made material. Due to the increasing of population
in the world, a waste material also increases. In those waste materials many are non- degradable materials, they make hazards to
the environment.So, that usage of non degradable waste [1] in concrete will be safe for disposal. This project will give the ideas,
experimental analysis of the recycled aggregates (Coarse Aggregates) and waste glass materials (Fine aggregates) on the
concrete mix. Desired properties of concrete such as strength,, workability,durability can also achieved by adding above
materials in the concrete.
Keywords: Recycled Aggregate, Powder of Waste Glass, Coarse Aggregate-Partial Replacement, Fine Aggregate,
Compression Test, Flexural Strength, Split Tensile Test
Utilization of Coconut Shell in Different Forms in Concreteijsrd.com
The rising cost of material is a matter of concern in this developing construction environment. The prices of building material such as cement, sand, gravel etc. are increasing day by day. The reason for increase in cost is high demand and less availability of material. Nowadays, most of the researchers are doing research on the material which can reduce the cost of construction as well as increase the strength. Research on waste material such as fly ash, rice husk, slag and sludge from treatment of industrial and domestic waste water demolished building material is being done. Use of coconut shell in concrete is not only useful economically but also environmentally useful for human being. Coconut shell is one of the main contributors of pollution problem as a solid waste. Coconut shell used as coarse aggregate in concrete encouraged sustainable and environmentally helpful material in the construction field. Since cement rate increases day per day and its availability is decreasing as per time so it can be useful to use coconut shell ash used as substitute of cement in concrete. Coconut shell can be used in the form of powder with epoxy resins or epoxy matrixes in concrete also. Composites are made by combining two or more natural or artificial materials to maximize their useful properties and minimize their weaknesses.
Experimental Study of Partial Replacement of Fine Aggregate with Waste Materi...IJRES Journal
The utilization of industrial and agricultural waste produced by industrial process has been the focus of waste reduction research for economical, environmental and technical reasons. This is because over 300 million tones of industrial waste are being produced per annual by agricultural and industrial process in India. The problem arising from continuous technological and industrial development is the disposal of waste material. If some of the waste materials are found suitable in concrete making not only cost of construction can be cut down, but also safe disposal of waste material can be achieved. The cement of high strength concrete is generally high which often leads to higher shrinkage and greater evaluation of neat of hydration besides increase in cost. A partial substitution of cement by an industrial waste is not only economical but also improves the properties of fresh and hardened concrete and enhance the durability characteristics besides the safe disposal of waste material thereby protecting the environment form pollution This paper deals with partial replacement of fine aggregate with the industrial waste from China Clay industries. The compressive strength, split tensile strength and flexural strength of conventional concrete and fine aggregate replaced concrete are compared and the results are tabulated.
Partial replacement of coarse aggregates by expanded polystyrene beads in con...eSAT Journals
Abstract With the increase in demand for construction materials, there is a strong need to utilize alternative materials for sustainable development. The main objective of this investigation is to study the properties, such as compressive strength and tensile strengths of lightweight concrete containing Expanded Polystyrene (EPS) beads. Its properties are compared with those of the normal concrete i.e., without EPS beads. EPS beads are used as partial replacement to coarse aggregates. The results showed that the amount of polystyrene beads incorporated in concrete influences the properties of hardened concrete. At 28 days, it was found that compressive strength of 5%, 10%, 15%, 20%, 25% and 30% EPS incorporated concrete strengths were 91%, 77 %, 71%, 63%, 57%, and 45%, respectively when compared to concrete with no EPS case. Key Words: Expanded polystyrene beads (EPS); Workability; Compressive strength; Splitting tensile strength;
Experimental Analysis of the Use of Coconut Shell as Coarse AggregateIOSR Journals
The high cost of conventional building materials is a major factor affecting housing delivery in the
world. This has necessitated research into alternative materials of construction. In this study, coconut shell is
used as light weight aggregate in concrete. The properties of coconut shell and coconut shell aggregate
concrete is examined and the use of coconut shell aggregate in construction is tested. The project paper aims at
analyzing flexural and compressive strength characteristics of with partial replacement using M30 grade
concrete. The project also aims to show that Coconut shell aggregate is a potential construction material and
simultaneously reduces the environment problem of solid..Beams are casted, tested and their physical and
mechanical properties are determined. The main objective is to encourage the use of these „seemingly‟ waste
products as construction materials in low-cost housing.
An experimental laboratory study on utilisation of e waste as a partial repla...eSAT Journals
Abstract
The Growth in the Electronics sector has been rapid and this rapid growth is due to continuous upgradation of technology and introduction of new technologies to the market. This has led to one of the fastest growing solid waste in the world, simply called as E-waste. India is the 5th highest e-waste producer in the world. The rapid increase in the construction activity in India, has resulted in huge demand for the aggregates to be used in the concrete. This has led to depletion of natural resources and adverse changes in the environment. This rapid development in the infrastructure sector has led to shortage of natural sand. This paper outlines the experimental work carried for utilisation of e-waste as a partial replacement for the fine aggregates. Strength tests and durability tests are conducted on hardened concrete. Results show that the partial use of E- waste as fine aggregates results in much higher workable and less dense concrete. This study gives an Economic, environment friendly and efficient disposal method for E-waste to be used as a partial replacement to the fine aggregates in concrete.
Keywords: E-waste, M-Sand, Fine aggregate replacement, Concrete, Durabilityetc.
The high cost of materials for anyconventional
building is a major factor that affects the housing delivery
worldwide. This has necessitated research for alternative cost
effective materials in construction. The paper aims at analyzing
characteristic compressive and tensile strength of coconut shells
of concrete produced. By partial replacement using crushed,
granular coconut shells as a substitute for conventional coarse
aggregate in M20 grade concrete. The cube and cylinder are
casted, tested then physical and mechanical properties are
determined. In this studies, three different concrete mixes with
different the combination of natural material content namely
0%, 25%, 50%. Three samples specimen will be prepare for each
concrete mixes. The parameters will be tested are compressive
strength, tensile strength.
This paper analyzed an investigation on the behavior of
concrete specimens produce from coconut shell aggregate. A total
of 36 specimens with varying percentage of replacement were
casted and tested. The attempt is made to prove in all respect the
serviceability and durability, experimental study is satisfying and
can be implemented in rural areas by considering all technical
aspect
Investigation of Crack Width Development in Reinforced Concrete Beams Using F...IJERA Editor
Due to increase in thermal power plants in India lot of fly ash is produced. The disposal of fly ash causes
negative impact on the environment in the way of water pollution, air pollution and finally effect on the eco
system. Hence disposal of fly ash is challenging task for engineers.
Lot of earlier investigations reported that fly ash has some cementing properties it can be replaced as cement
upto some percentage. Hence in this investigation an attempt has been made to replace the cement by fly ash
and investigated the resulting properties.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Experimental Study on Performance of Concrete M30 with Partial Replacement of...IJERA Editor
In this research work experiments have been conducted with collection of materials required and the data required for mix design are obtained by sieve analysis and specific gravity test. Sieve analysis is carried out from various fine aggregates (FA) and coarse aggregates (CA) samples and the sample which suits the requirement is selected. Specific gravity tests are carried out for fine and coarse aggregate. The various materials used were tested as per Indian standard specifications. On the basis of the experimental studies carried out on M30 grade concrete as partial replacement of coarse aggregates with sea shells and coconut shells, the following conclusions are drawn from the above experiment we conclude that comparing to traditional concrete, compressive strength of 10% (5% + 5%) of coconut shells (5%) and sea shells (5%) increased. whereas the compressive strength of the concrete cubes has gradually decreased from addition of 10% (5% + 5%) of coconut shells and sea shells. Hence for economical view 10% is preferable and in the perspective of compressive strength 10% is suggested. Thus, 10% replacement coconut shells and sea shells are recommended for both heavy weight and light weight concrete production.
Review Paper on Application of Waste Plastic in Modifying Bitumen PropertiesIJERA Editor
Industrialisation and population is increasing day by day leading to the increase in the amount of waste plastic. Plastic is a non-biodegradable substance i.e. it is not decomposed by bacteria easily. So, dumping it causes soil pollution which leads to decrease in the fertility of soil. Another way of getting rid of plastic is by burning it, which also produces a lot of harmful gases and leads to increase in air pollution. Soil and air pollution both are harmful for the environment. Waste plastic can be used in bitumen as a modifier. In this paper we will discuss the variation of the properties of bitumen on addition of waste plastic at different percentage
Utilization of Coconut Shell in Different Forms in Concreteijsrd.com
The rising cost of material is a matter of concern in this developing construction environment. The prices of building material such as cement, sand, gravel etc. are increasing day by day. The reason for increase in cost is high demand and less availability of material. Nowadays, most of the researchers are doing research on the material which can reduce the cost of construction as well as increase the strength. Research on waste material such as fly ash, rice husk, slag and sludge from treatment of industrial and domestic waste water demolished building material is being done. Use of coconut shell in concrete is not only useful economically but also environmentally useful for human being. Coconut shell is one of the main contributors of pollution problem as a solid waste. Coconut shell used as coarse aggregate in concrete encouraged sustainable and environmentally helpful material in the construction field. Since cement rate increases day per day and its availability is decreasing as per time so it can be useful to use coconut shell ash used as substitute of cement in concrete. Coconut shell can be used in the form of powder with epoxy resins or epoxy matrixes in concrete also. Composites are made by combining two or more natural or artificial materials to maximize their useful properties and minimize their weaknesses.
Experimental Study of Partial Replacement of Fine Aggregate with Waste Materi...IJRES Journal
The utilization of industrial and agricultural waste produced by industrial process has been the focus of waste reduction research for economical, environmental and technical reasons. This is because over 300 million tones of industrial waste are being produced per annual by agricultural and industrial process in India. The problem arising from continuous technological and industrial development is the disposal of waste material. If some of the waste materials are found suitable in concrete making not only cost of construction can be cut down, but also safe disposal of waste material can be achieved. The cement of high strength concrete is generally high which often leads to higher shrinkage and greater evaluation of neat of hydration besides increase in cost. A partial substitution of cement by an industrial waste is not only economical but also improves the properties of fresh and hardened concrete and enhance the durability characteristics besides the safe disposal of waste material thereby protecting the environment form pollution This paper deals with partial replacement of fine aggregate with the industrial waste from China Clay industries. The compressive strength, split tensile strength and flexural strength of conventional concrete and fine aggregate replaced concrete are compared and the results are tabulated.
Partial replacement of coarse aggregates by expanded polystyrene beads in con...eSAT Journals
Abstract With the increase in demand for construction materials, there is a strong need to utilize alternative materials for sustainable development. The main objective of this investigation is to study the properties, such as compressive strength and tensile strengths of lightweight concrete containing Expanded Polystyrene (EPS) beads. Its properties are compared with those of the normal concrete i.e., without EPS beads. EPS beads are used as partial replacement to coarse aggregates. The results showed that the amount of polystyrene beads incorporated in concrete influences the properties of hardened concrete. At 28 days, it was found that compressive strength of 5%, 10%, 15%, 20%, 25% and 30% EPS incorporated concrete strengths were 91%, 77 %, 71%, 63%, 57%, and 45%, respectively when compared to concrete with no EPS case. Key Words: Expanded polystyrene beads (EPS); Workability; Compressive strength; Splitting tensile strength;
Experimental Analysis of the Use of Coconut Shell as Coarse AggregateIOSR Journals
The high cost of conventional building materials is a major factor affecting housing delivery in the
world. This has necessitated research into alternative materials of construction. In this study, coconut shell is
used as light weight aggregate in concrete. The properties of coconut shell and coconut shell aggregate
concrete is examined and the use of coconut shell aggregate in construction is tested. The project paper aims at
analyzing flexural and compressive strength characteristics of with partial replacement using M30 grade
concrete. The project also aims to show that Coconut shell aggregate is a potential construction material and
simultaneously reduces the environment problem of solid..Beams are casted, tested and their physical and
mechanical properties are determined. The main objective is to encourage the use of these „seemingly‟ waste
products as construction materials in low-cost housing.
An experimental laboratory study on utilisation of e waste as a partial repla...eSAT Journals
Abstract
The Growth in the Electronics sector has been rapid and this rapid growth is due to continuous upgradation of technology and introduction of new technologies to the market. This has led to one of the fastest growing solid waste in the world, simply called as E-waste. India is the 5th highest e-waste producer in the world. The rapid increase in the construction activity in India, has resulted in huge demand for the aggregates to be used in the concrete. This has led to depletion of natural resources and adverse changes in the environment. This rapid development in the infrastructure sector has led to shortage of natural sand. This paper outlines the experimental work carried for utilisation of e-waste as a partial replacement for the fine aggregates. Strength tests and durability tests are conducted on hardened concrete. Results show that the partial use of E- waste as fine aggregates results in much higher workable and less dense concrete. This study gives an Economic, environment friendly and efficient disposal method for E-waste to be used as a partial replacement to the fine aggregates in concrete.
Keywords: E-waste, M-Sand, Fine aggregate replacement, Concrete, Durabilityetc.
The high cost of materials for anyconventional
building is a major factor that affects the housing delivery
worldwide. This has necessitated research for alternative cost
effective materials in construction. The paper aims at analyzing
characteristic compressive and tensile strength of coconut shells
of concrete produced. By partial replacement using crushed,
granular coconut shells as a substitute for conventional coarse
aggregate in M20 grade concrete. The cube and cylinder are
casted, tested then physical and mechanical properties are
determined. In this studies, three different concrete mixes with
different the combination of natural material content namely
0%, 25%, 50%. Three samples specimen will be prepare for each
concrete mixes. The parameters will be tested are compressive
strength, tensile strength.
This paper analyzed an investigation on the behavior of
concrete specimens produce from coconut shell aggregate. A total
of 36 specimens with varying percentage of replacement were
casted and tested. The attempt is made to prove in all respect the
serviceability and durability, experimental study is satisfying and
can be implemented in rural areas by considering all technical
aspect
Investigation of Crack Width Development in Reinforced Concrete Beams Using F...IJERA Editor
Due to increase in thermal power plants in India lot of fly ash is produced. The disposal of fly ash causes
negative impact on the environment in the way of water pollution, air pollution and finally effect on the eco
system. Hence disposal of fly ash is challenging task for engineers.
Lot of earlier investigations reported that fly ash has some cementing properties it can be replaced as cement
upto some percentage. Hence in this investigation an attempt has been made to replace the cement by fly ash
and investigated the resulting properties.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Experimental Study on Performance of Concrete M30 with Partial Replacement of...IJERA Editor
In this research work experiments have been conducted with collection of materials required and the data required for mix design are obtained by sieve analysis and specific gravity test. Sieve analysis is carried out from various fine aggregates (FA) and coarse aggregates (CA) samples and the sample which suits the requirement is selected. Specific gravity tests are carried out for fine and coarse aggregate. The various materials used were tested as per Indian standard specifications. On the basis of the experimental studies carried out on M30 grade concrete as partial replacement of coarse aggregates with sea shells and coconut shells, the following conclusions are drawn from the above experiment we conclude that comparing to traditional concrete, compressive strength of 10% (5% + 5%) of coconut shells (5%) and sea shells (5%) increased. whereas the compressive strength of the concrete cubes has gradually decreased from addition of 10% (5% + 5%) of coconut shells and sea shells. Hence for economical view 10% is preferable and in the perspective of compressive strength 10% is suggested. Thus, 10% replacement coconut shells and sea shells are recommended for both heavy weight and light weight concrete production.
Review Paper on Application of Waste Plastic in Modifying Bitumen PropertiesIJERA Editor
Industrialisation and population is increasing day by day leading to the increase in the amount of waste plastic. Plastic is a non-biodegradable substance i.e. it is not decomposed by bacteria easily. So, dumping it causes soil pollution which leads to decrease in the fertility of soil. Another way of getting rid of plastic is by burning it, which also produces a lot of harmful gases and leads to increase in air pollution. Soil and air pollution both are harmful for the environment. Waste plastic can be used in bitumen as a modifier. In this paper we will discuss the variation of the properties of bitumen on addition of waste plastic at different percentage
STUDIES ON STABILIZED MUD BLOCK AS A CONSTRUCTION MATERIALAM Publications
Soil as a building material is available in most areas of the world. In developing countries, earth
construction is economically the most efficient means for house construction with the least demand of resources.
Investigation is carried out to find the suitable proportion of locally available materials such as soil , coir , straw etc. with
cement as stabilizers for improving the strength of locally available mud blocks and thus to provide affordable housing.
Using soil (from areas of Neriamangalam) and stabilizers (cement, lime, straw fibre, coir fibre, plastic fibre), eleven
different types of samples were prepared. Tests were conducted on these samples in order to evaluate their performance
such as compressive strength and total water absorption on which the durability of the blocks depend. The investigation
has revealed that, out of all block samples, blocks which are produced from10% cement (C10), 10% cement with 3% coir
fibre (C10C) and 10% cement with 3% plastic fibre (C10P) have compressive strength and total water absorption values
above the recommended minimum values for structural work.(IS 1725:1992)
Partially Replacement of Clay by S.T.P. Sludge in Brick ManufacturingAM Publications
In many countries, sludge is a serious problem due to its high treatment costs and the risks to environment and human health. The sludge presents increasingly difficult problem to cities of all sizes because of the scarcity of suitable disposal sites, increasing labour costs, and environmental concerns. The study investigated the use of water treatment sludge incorporated with clay. In this study bricks were produced with sewage sludge additions ranging from 20, 25, 30 and 40% by dry weight respectively and compare produce brick with regular brick. Bricks with a sludge content of up to 40 % were capable of meeting the relevant technical standards. However, if bricks with more than 30 % sludge addition are not recommended for use because they are brittle in nature and easily broken even when handled gently as well as colour is not as per the requirement. Also from this investigation me can solve disposal problem completely and also construct and economical structure with easy designing.
Papercrete Bricks An Alternative Sustainable Building MaterialIJERA Editor
A large amount of non-renewable resources is consumed by the construction industry throughout the world. Everyday tons of waste papers are discarded as landfill or dump sites than those recycled. It is learnt that it takes about fifteen trees to make a ton of paper which means that 720 million trees are used once and then buried as landfills each year. In order to address these issues it has become imperative to push the boundaries of research in the field of innovative sustainable construction materials. This study is one such kind of efforts. Papercrete is a new composite material comprising of waste papers and cement. In this investigation, an attempt is made to produce an alternative material using waste papers. This could help eradicate a few of the environmental hazards caused by the construction industry. But there is no proper code for the mix proportioning of papercrete bricks. Therefore, a mix proportion of [Cement: Paper : Sand] 1:1.15:1.3 was chosen on trial and error basis. All the necessary engineering properties are studied and compared with the conventional bricks and discussions on its potential uses are made.
Use of Over-Burnt Bricks as Coarse aggregate in ConcreteEditorIJAERD
In modern construction industry number of materials are used and one of the materials is Brick. Regular
bricks are generally used in buildings or in some other engineering applications. In manufacturing of these bricks, a lot
of waste is produced in the form of over- burnt-bricks. The bricks being near to the fire in the furnace receives a
temperature more heat and eventually shrink and loose its shape, its color becomes reddish. These bricks can’t be used
in construction, directly because of their distorted shape dark color. hose over-burnt brick could be a source of recycled
coarse aggregate. The primary goal of this paper is to assess the suitability of incorporating over-burnt bricks in
concrete, by the partial replacement of natural coarse aggregate (NCA) with overburnt brick aggregate (OBBA) in a
ratio of 20%, 50%, and 100%. Initially, mix proportion of 1:2:4 and w/c of 0.57 was selected. By replacing NCA with
OBBA while using mix proportion of 1:2:4 and w/c of 0.57, the resulting concrete was found non-mixable and nonworkable. Thus, mix was designed (for targeted strength of 4ksi) for all replacement percentages. Slump test was
conducted for each replacement and the results show that by increasing replacement percentage the workability of
concrete decreases. the slump values are in between the range of 3–1.5 inches. For compressive strength the cylindrical
specimens of 6" x 12" were tested at 3, 7, and 28 days. For 20% replacement, the loss in compressive strength is 42.16%
for 3 days and for 7 and 28 days the loss is 46.96% and 61.37% respectively. For 50 % replacement, the loss in strength
for 3, 7 and 28 days is 29.73%, 30.87% and 58.29% respectively. For 100% replacement, the loss in strength for 3, 7 and
28 days is 48.65%, 55.65% and 69.19%.
Explore the innovative world of trenchless pipe repair with our comprehensive guide, "The Benefits and Techniques of Trenchless Pipe Repair." This document delves into the modern methods of repairing underground pipes without the need for extensive excavation, highlighting the numerous advantages and the latest techniques used in the industry.
Learn about the cost savings, reduced environmental impact, and minimal disruption associated with trenchless technology. Discover detailed explanations of popular techniques such as pipe bursting, cured-in-place pipe (CIPP) lining, and directional drilling. Understand how these methods can be applied to various types of infrastructure, from residential plumbing to large-scale municipal systems.
Ideal for homeowners, contractors, engineers, and anyone interested in modern plumbing solutions, this guide provides valuable insights into why trenchless pipe repair is becoming the preferred choice for pipe rehabilitation. Stay informed about the latest advancements and best practices in the field.
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...Amil Baba Dawood bangali
Contact with Dawood Bhai Just call on +92322-6382012 and we'll help you. We'll solve all your problems within 12 to 24 hours and with 101% guarantee and with astrology systematic. If you want to take any personal or professional advice then also you can call us on +92322-6382012 , ONLINE LOVE PROBLEM & Other all types of Daily Life Problem's.Then CALL or WHATSAPP us on +92322-6382012 and Get all these problems solutions here by Amil Baba DAWOOD BANGALI
#vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore#blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #blackmagicforlove #blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #Amilbabainuk #amilbabainspain #amilbabaindubai #Amilbabainnorway #amilbabainkrachi #amilbabainlahore #amilbabaingujranwalan #amilbabainislamabad
Automobile Management System Project Report.pdfKamal Acharya
The proposed project is developed to manage the automobile in the automobile dealer company. The main module in this project is login, automobile management, customer management, sales, complaints and reports. The first module is the login. The automobile showroom owner should login to the project for usage. The username and password are verified and if it is correct, next form opens. If the username and password are not correct, it shows the error message.
When a customer search for a automobile, if the automobile is available, they will be taken to a page that shows the details of the automobile including automobile name, automobile ID, quantity, price etc. “Automobile Management System” is useful for maintaining automobiles, customers effectively and hence helps for establishing good relation between customer and automobile organization. It contains various customized modules for effectively maintaining automobiles and stock information accurately and safely.
When the automobile is sold to the customer, stock will be reduced automatically. When a new purchase is made, stock will be increased automatically. While selecting automobiles for sale, the proposed software will automatically check for total number of available stock of that particular item, if the total stock of that particular item is less than 5, software will notify the user to purchase the particular item.
Also when the user tries to sale items which are not in stock, the system will prompt the user that the stock is not enough. Customers of this system can search for a automobile; can purchase a automobile easily by selecting fast. On the other hand the stock of automobiles can be maintained perfectly by the automobile shop manager overcoming the drawbacks of existing system.
Forklift Classes Overview by Intella PartsIntella Parts
Discover the different forklift classes and their specific applications. Learn how to choose the right forklift for your needs to ensure safety, efficiency, and compliance in your operations.
For more technical information, visit our website https://intellaparts.com
Courier management system project report.pdfKamal Acharya
It is now-a-days very important for the people to send or receive articles like imported furniture, electronic items, gifts, business goods and the like. People depend vastly on different transport systems which mostly use the manual way of receiving and delivering the articles. There is no way to track the articles till they are received and there is no way to let the customer know what happened in transit, once he booked some articles. In such a situation, we need a system which completely computerizes the cargo activities including time to time tracking of the articles sent. This need is fulfilled by Courier Management System software which is online software for the cargo management people that enables them to receive the goods from a source and send them to a required destination and track their status from time to time.
Vaccine management system project report documentation..pdfKamal Acharya
The Division of Vaccine and Immunization is facing increasing difficulty monitoring vaccines and other commodities distribution once they have been distributed from the national stores. With the introduction of new vaccines, more challenges have been anticipated with this additions posing serious threat to the already over strained vaccine supply chain system in Kenya.
CFD Simulation of By-pass Flow in a HRSG module by R&R Consult.pptxR&R Consult
CFD analysis is incredibly effective at solving mysteries and improving the performance of complex systems!
Here's a great example: At a large natural gas-fired power plant, where they use waste heat to generate steam and energy, they were puzzled that their boiler wasn't producing as much steam as expected.
R&R and Tetra Engineering Group Inc. were asked to solve the issue with reduced steam production.
An inspection had shown that a significant amount of hot flue gas was bypassing the boiler tubes, where the heat was supposed to be transferred.
R&R Consult conducted a CFD analysis, which revealed that 6.3% of the flue gas was bypassing the boiler tubes without transferring heat. The analysis also showed that the flue gas was instead being directed along the sides of the boiler and between the modules that were supposed to capture the heat. This was the cause of the reduced performance.
Based on our results, Tetra Engineering installed covering plates to reduce the bypass flow. This improved the boiler's performance and increased electricity production.
It is always satisfying when we can help solve complex challenges like this. Do your systems also need a check-up or optimization? Give us a call!
Work done in cooperation with James Malloy and David Moelling from Tetra Engineering.
More examples of our work https://www.r-r-consult.dk/en/cases-en/