This document presents the results of a study on the behavioral effects of partially replacing cement with fly ash in concrete. Fly ash is a byproduct of burning coal that can be used as a supplementary cementitious material in concrete. The study investigated replacing cement at levels of 0%, 10%, 20%, and 30% by weight with fly ash in M20 grade concrete mixes. Concrete cubes were cast and tested for compressive strength at 7, 14, and 28 days. The results showed that compressive strength decreased with higher levels of fly ash replacement but was maintained at replacement levels up to 20-30%. Overall, the study aimed to determine the optimum level of fly ash replacement in concrete mixtures to reduce cement usage while maintaining adequate strength.
As concrete is the most abundant material used in the world, it contains aggregate content of around 60 to 70 %. Since aggregate are being used rapidly there has been a scarcity in the avaibility of these materials. This research investigates the effect of partially replacing aggregates by burnt brick bats and lateritic fines in concrete respectively for M25 grade concrete. The incorporation is done for 5%, 10% and 15% of burnt brick bats for coarse aggregate and by talking 15% of lateritic fines as constant for fine aggregate by conducting compressive strength test which gave the optimum value of 15% for natural sand. The compressive strength, split tensile strength and flexural strength was conducted. The results showed density of of the concrete incorporating brick and laterite was lower compared to conventional concrete, the concrete with 5% burnt brick and 15% lateritic soil showed increased strength for 7 days compared to normal concrete but when 28 days test was conducted the strength was similar to conventional concrete. The split tensile and flexural strength of replaced concrete was found to be lower than the nominal concrete.
As concrete is the most abundant material used in the world, it contains aggregate content of around 60 to 70 %. Since aggregate are being used rapidly there has been a scarcity in the avaibility of these materials. This research investigates the effect of partially replacing aggregates by burnt brick bats and lateritic fines in concrete respectively for M25 grade concrete. The incorporation is done for 5%, 10% and 15% of burnt brick bats for coarse aggregate and by talking 15% of lateritic fines as constant for fine aggregate by conducting compressive strength test which gave the optimum value of 15% for natural sand. The compressive strength, split tensile strength and flexural strength was conducted. The results showed density of of the concrete incorporating brick and laterite was lower compared to conventional concrete, the concrete with 5% burnt brick and 15% lateritic soil showed increased strength for 7 days compared to normal concrete but when 28 days test was conducted the strength was similar to conventional concrete. The split tensile and flexural strength of replaced concrete was found to be lower than the nominal concrete.
Partial Replacement of Cement by Saw Dust Ash in Concrete A Sustainable ApproachIJERD Editor
Concrete industry is one of the largest consumers of natural resources due to which sustainability of concrete industry is under threat. The environmental and economic concern is the biggest challenge concrete industry is facing. In this paper, the issues of environmental and economic concern are addressed by the use of saw dust ash as partial replacement of cement in concrete. Cement was replaced by Saw Dust Ash as 5%, 10%, 15% and 20% by weight for M-25 mix. The concrete specimens were tested for compressive strength, durability (water absorption) and density at 28 days of age and the results obtained were compared with those of normal concrete. The results concluded the permissibility of using Saw Dust Ash as partial replacement of cement up to 10% by weight for particle size of range 90micron.
“Experimental studies on the characteristics properties of concrete produced ...AjeetPanedakatti
Concrete is the most widely used man-made construction material in the world and is consumed second only to water on this planet. It is obtained by mixing the cementitious materials, water and aggregates in the required proportions. However, the various required performance attributes of concrete including strength, workability, dimensional stability and durability, often impose contradictory requirements on the mix parameters to be adopted, there by rendering the concrete mix design a very difficult task.
The increase in global warming has resulted a wide range of change in earth’s temperature, the source being emission of carbon dioxide gas from the production process of cement. Use of naturally available pozzolanic waste materials (fly ash & granite powder) as a partial substitute of OPC cement in mortar mix has seen a wide potential in the utilization of these waste material and also enhancing the properties of mortar mix and thus reducing the environment impact caused by manufacturing of cement. In this study the effect of using fly ash & granite powder is used as a partial substitute of ordinary port-land cement and to reduce the cost of the cement.
An investigation was conducted to determine the suitability of using fly ash (bi-product from thermal power plant) and waste granite powder as partial replacement for cement for concrete production. Apart from the control concrete sample which had 100% cement all the other samples were treated to 20%, 40%, 60%, 80% and 100% replacement of cement with flyash and granite powder. Concrete cubes of 150mmx150mmx150mm, cylinders of 150mm diameter and 300mm height, beams of 100mmx100mmx500mm were made with the various proportions of cement, sand and coarse aggregates in a mix ratio of 1:2.2:3, water -cement ratio of 0.50 and cured over 28 days. The results of compressive strength tests show that the strength of the concrete cubes with varying amounts of cement and fly ash and granite powder changed marginally. This was interpreted to mean that the partial replacement of cement with fly ash and granite powder up to 20% in concrete results in about 1.4% increase in the strength of the concrete. The compressive strength of concrete cubes is 33N/mm2, flexural strength of concrete beams is 5.10 N/mm2 and split tensile strength of concrete cylinder is 2.34 N/mm2 for 20% replacement.
Disposal of tyre rubber is becoming a huge problem in India day by day.
Researchers are trying to use those rubber in civil engineering projects from long day
back. Crumb rubber replaced fine aggregate is qute a common practice now a days.
An attempt was made to replace 10% chipped rubber with coarse aggregate and
beams were casted with that concrete mix.They were tested to failure. Deflection,
ultimate load, first crack,stress vs strain,load vs deflection are all studied. Efforts
have been taken to identify the potential application of waste tyres in civil engineering
projects. This study can show an alternative way of recycling tyre by incorporating
them into concrete construction. Main focus was made on the behaviour of beam
made from recycled rubber chips .
EFFECT OF BAGAGSE ASH ON PROPERTIES OF CONCRETE USED AS PARTIAL REPLACEMNT FO...IAEME Publication
Background/Objectives: Cement is one of the sources for producing inexperienced house gases united ton of carbon dioxide is created with each one ton of cement production. Use of alternative materials will scale back this pollution downside. Methods/ Statistical analysis: In the present work Sugarcane pulp ash has been tried as another material for partial replacement of cement. Sugarcane bagasse ash is a by-product of sugarcane and disposal of that is making serious setting issues. In the present work, trails are created (with 0%, 5%, 10%, 15%, 20% and 25%) to value absolutely the quantum of cement that may get replaced by bagasse ash while not poignant the strength capabilities of the cast. Findings: Different tests such as compressive strength, flexure strength and split tensile strength are to be conducted on concrete for seven days and twenty-eight days natural process. Analysis of the results would give conclusions and inferences. Applications/Improvements: Outcome shows that for 15% substitute of cement by way of the SCBA strength is nearly enough the nominal force of the concrete.
An Experimental Study on Short Term Durability and Hardened Properties of Bag...Dr. Amarjeet Singh
This project reports the comparison of bagasse ash and fly ash-bagasse ash based on geopolymer concrete. In which cement is fully replaced by pozzolanic material that is rich in silicon and aluminium like fly ash and bagasse ash referred to as “Geopolymer concrete” which is a contemporary material. Geopolymer concrete was actually manufactured by reusing and recycling of industrial solid wastes and by products. Fly Ash, a by-product of coal obtained from the thermal power plant is plenty available worldwide. Fly ash is used as ingredients in concrete which enhance the properties of concrete and utilization of fly ash is helpful for consumption. Bagasse ash is a final waste product of sugar obtained from the sugar mills. The base material, viz. fly ash and Bagasse ash, is activated by alkaline solution that is sodium hydroxide and sodium silicate to produce a binder which is rich in silica and aluminium. Sample 1 is cement. It is replaced by 100% fly ash geopolymer concrete and trial 2 is 10%, 30% & 50% replaced by Bagasse ash in Geopolymer concrete . The project presents the strength and durability of Bagasse ash based Geopolymer concrete and fly ash and Bagasse ash based Geopolymer concrete.
Performance of lateritic concrete under environmental harsh conditioneSAT Journals
Abstract This is an investigation of weathering characteristics of Laterized concrete with laterite-fine aggregate ratio as a factor. It was done with a view of ascertaining the suitability of laterite as aggregate substitutes at 0, 10, 20, 30 and 40% of fine aggregate used in the construction industry. The weathering characteristics were examined by conditioning laterized concrete cubes to varying temperatures, chemical and alternate wetting and drying, which all represent the operating weather conditions (wet and dry seasons) in tropics, including Nigeria. The mix proportion used was 1:2:4, the curing age of the laterized concrete was based on 28days curing age, while the compressive strength of the treated laterized concrete cubes was determined. The result of this research showed that the compressive strength of laterized concrete with laterite-fine aggregate ratio variation decreases when subjected to alternate wetting and drying and increases when subjected to magnesium sulphate (Mg2SO4). It was also discovered that a laterized concrete with a laterite-fine aggregate ratio of 20% conditioned to a temperature range of 100oC attained optimum compressive strength of 12.90Nmm-2 Keywords: Laterized Concrete, Comprehensive strength, Weathering Characteristics
Replacement of Natural Fine Aggregate With Air Cooled Blast Furnace Slag An I...IJERA Editor
The aim of the investigation is to replace natural fine aggregatewith Air Cooled Blast Furnace Slag in OPC concrete. At present, nearly million tons of slag is being produced in the steel plants, in India. The generation of slag would be dual problem in disposal difficulty and environmental pollution. Some strategies should be used to utilize the slag effectively. Considering physical properties of metallurgical slags and a series of possibilities for their use in the field of civil constructions, this report demonstrates the possibilities of using air cooled blast furnace slag as partial replacement of sand in concrete. A total of five concrete mixes, containing 0%, 12.5%, 25%, 37.5% and 50% partial replacement of regular sand with air cooled blast furnace slag are investigated in the laboratory. These mixes were tested to determine axial compressive strength, split tensile strength, and flexural strength for 7days, 28days, 56days and 90days.
Study on mechanical properties of concrete with industrial wasteseSAT Journals
Abstract
Utilization of Industrial waste, construction waste, agriculture waste, commercial waste etc... In concrete plays a vital role in minimizing the disposal problems. Over 300 million tons of industrial wastes are being produced per annum by chemical and agricultural process in India. These materials poses problems of disposal, health hazards and aesthetic problem. Hypo Sludge (HS) is a waste material produced from paper industry that can used as a cement replacement material in concrete since the lime content in the sludge is large. Copper slag is a waste material produced from copper manufacturing process and this can be used as a replacement material for fine aggregate (sand) since the particle size similar to sand. During the present study, an attempt had been made to study the mechanical properties of concrete in which Hypo sludge and Copper slag were as a replacement material for cement and fine aggregate respectively. Replacement percentage used during this study were 10%, 20% and 30% of Hypo sludge for cement. Fine aggregate was replaced with 30%, 40% and 50% of Copper slag. Compressive strength of cubes were found on 7th, 28th and 56th days. Split tensile strengths of the cylinders were found on 28th and 56th days. Flexural strengths of prism specimens were found on 28th day. It has been found that usage of Hypo sludge and Copper slag as a replacement material has beneficial effects on the Mechanical properties of concrete.
Keywords: Hypo sludge, Copper slag, Compressive strength, Split tensile strength, Flexural strength.
STUDY ON GEOPOLYMER CONCRETE USED FOR PAVING BLOCKSAM Publications
Paver block is used in various applications like in street road and other construction places. Portland cement generates large amounts of carbon dioxide (CO2) which is responsible for global warming hence it is a greenhouse gas. And the concrete paver block production consume large amount of water and space for curing purpose. The other great problem today is disposal of solid waste from Coal fired thermal power plants generate fly ash and pond ash. This project combined sustainability, curing free with waste management leading to a wonderful product called geo-polymer concrete pavers. This paper represents the results of the geopolymer concrete paver block with the mix of M40 grade Test results indicate that low calcium fly ash based geopolymer concrete pavers has excellent compressive strength within short period (3 days) without water curing & suitable for practical applications
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Partial Replacement of Cement by Saw Dust Ash in Concrete A Sustainable ApproachIJERD Editor
Concrete industry is one of the largest consumers of natural resources due to which sustainability of concrete industry is under threat. The environmental and economic concern is the biggest challenge concrete industry is facing. In this paper, the issues of environmental and economic concern are addressed by the use of saw dust ash as partial replacement of cement in concrete. Cement was replaced by Saw Dust Ash as 5%, 10%, 15% and 20% by weight for M-25 mix. The concrete specimens were tested for compressive strength, durability (water absorption) and density at 28 days of age and the results obtained were compared with those of normal concrete. The results concluded the permissibility of using Saw Dust Ash as partial replacement of cement up to 10% by weight for particle size of range 90micron.
“Experimental studies on the characteristics properties of concrete produced ...AjeetPanedakatti
Concrete is the most widely used man-made construction material in the world and is consumed second only to water on this planet. It is obtained by mixing the cementitious materials, water and aggregates in the required proportions. However, the various required performance attributes of concrete including strength, workability, dimensional stability and durability, often impose contradictory requirements on the mix parameters to be adopted, there by rendering the concrete mix design a very difficult task.
The increase in global warming has resulted a wide range of change in earth’s temperature, the source being emission of carbon dioxide gas from the production process of cement. Use of naturally available pozzolanic waste materials (fly ash & granite powder) as a partial substitute of OPC cement in mortar mix has seen a wide potential in the utilization of these waste material and also enhancing the properties of mortar mix and thus reducing the environment impact caused by manufacturing of cement. In this study the effect of using fly ash & granite powder is used as a partial substitute of ordinary port-land cement and to reduce the cost of the cement.
An investigation was conducted to determine the suitability of using fly ash (bi-product from thermal power plant) and waste granite powder as partial replacement for cement for concrete production. Apart from the control concrete sample which had 100% cement all the other samples were treated to 20%, 40%, 60%, 80% and 100% replacement of cement with flyash and granite powder. Concrete cubes of 150mmx150mmx150mm, cylinders of 150mm diameter and 300mm height, beams of 100mmx100mmx500mm were made with the various proportions of cement, sand and coarse aggregates in a mix ratio of 1:2.2:3, water -cement ratio of 0.50 and cured over 28 days. The results of compressive strength tests show that the strength of the concrete cubes with varying amounts of cement and fly ash and granite powder changed marginally. This was interpreted to mean that the partial replacement of cement with fly ash and granite powder up to 20% in concrete results in about 1.4% increase in the strength of the concrete. The compressive strength of concrete cubes is 33N/mm2, flexural strength of concrete beams is 5.10 N/mm2 and split tensile strength of concrete cylinder is 2.34 N/mm2 for 20% replacement.
Disposal of tyre rubber is becoming a huge problem in India day by day.
Researchers are trying to use those rubber in civil engineering projects from long day
back. Crumb rubber replaced fine aggregate is qute a common practice now a days.
An attempt was made to replace 10% chipped rubber with coarse aggregate and
beams were casted with that concrete mix.They were tested to failure. Deflection,
ultimate load, first crack,stress vs strain,load vs deflection are all studied. Efforts
have been taken to identify the potential application of waste tyres in civil engineering
projects. This study can show an alternative way of recycling tyre by incorporating
them into concrete construction. Main focus was made on the behaviour of beam
made from recycled rubber chips .
EFFECT OF BAGAGSE ASH ON PROPERTIES OF CONCRETE USED AS PARTIAL REPLACEMNT FO...IAEME Publication
Background/Objectives: Cement is one of the sources for producing inexperienced house gases united ton of carbon dioxide is created with each one ton of cement production. Use of alternative materials will scale back this pollution downside. Methods/ Statistical analysis: In the present work Sugarcane pulp ash has been tried as another material for partial replacement of cement. Sugarcane bagasse ash is a by-product of sugarcane and disposal of that is making serious setting issues. In the present work, trails are created (with 0%, 5%, 10%, 15%, 20% and 25%) to value absolutely the quantum of cement that may get replaced by bagasse ash while not poignant the strength capabilities of the cast. Findings: Different tests such as compressive strength, flexure strength and split tensile strength are to be conducted on concrete for seven days and twenty-eight days natural process. Analysis of the results would give conclusions and inferences. Applications/Improvements: Outcome shows that for 15% substitute of cement by way of the SCBA strength is nearly enough the nominal force of the concrete.
An Experimental Study on Short Term Durability and Hardened Properties of Bag...Dr. Amarjeet Singh
This project reports the comparison of bagasse ash and fly ash-bagasse ash based on geopolymer concrete. In which cement is fully replaced by pozzolanic material that is rich in silicon and aluminium like fly ash and bagasse ash referred to as “Geopolymer concrete” which is a contemporary material. Geopolymer concrete was actually manufactured by reusing and recycling of industrial solid wastes and by products. Fly Ash, a by-product of coal obtained from the thermal power plant is plenty available worldwide. Fly ash is used as ingredients in concrete which enhance the properties of concrete and utilization of fly ash is helpful for consumption. Bagasse ash is a final waste product of sugar obtained from the sugar mills. The base material, viz. fly ash and Bagasse ash, is activated by alkaline solution that is sodium hydroxide and sodium silicate to produce a binder which is rich in silica and aluminium. Sample 1 is cement. It is replaced by 100% fly ash geopolymer concrete and trial 2 is 10%, 30% & 50% replaced by Bagasse ash in Geopolymer concrete . The project presents the strength and durability of Bagasse ash based Geopolymer concrete and fly ash and Bagasse ash based Geopolymer concrete.
Performance of lateritic concrete under environmental harsh conditioneSAT Journals
Abstract This is an investigation of weathering characteristics of Laterized concrete with laterite-fine aggregate ratio as a factor. It was done with a view of ascertaining the suitability of laterite as aggregate substitutes at 0, 10, 20, 30 and 40% of fine aggregate used in the construction industry. The weathering characteristics were examined by conditioning laterized concrete cubes to varying temperatures, chemical and alternate wetting and drying, which all represent the operating weather conditions (wet and dry seasons) in tropics, including Nigeria. The mix proportion used was 1:2:4, the curing age of the laterized concrete was based on 28days curing age, while the compressive strength of the treated laterized concrete cubes was determined. The result of this research showed that the compressive strength of laterized concrete with laterite-fine aggregate ratio variation decreases when subjected to alternate wetting and drying and increases when subjected to magnesium sulphate (Mg2SO4). It was also discovered that a laterized concrete with a laterite-fine aggregate ratio of 20% conditioned to a temperature range of 100oC attained optimum compressive strength of 12.90Nmm-2 Keywords: Laterized Concrete, Comprehensive strength, Weathering Characteristics
Replacement of Natural Fine Aggregate With Air Cooled Blast Furnace Slag An I...IJERA Editor
The aim of the investigation is to replace natural fine aggregatewith Air Cooled Blast Furnace Slag in OPC concrete. At present, nearly million tons of slag is being produced in the steel plants, in India. The generation of slag would be dual problem in disposal difficulty and environmental pollution. Some strategies should be used to utilize the slag effectively. Considering physical properties of metallurgical slags and a series of possibilities for their use in the field of civil constructions, this report demonstrates the possibilities of using air cooled blast furnace slag as partial replacement of sand in concrete. A total of five concrete mixes, containing 0%, 12.5%, 25%, 37.5% and 50% partial replacement of regular sand with air cooled blast furnace slag are investigated in the laboratory. These mixes were tested to determine axial compressive strength, split tensile strength, and flexural strength for 7days, 28days, 56days and 90days.
Study on mechanical properties of concrete with industrial wasteseSAT Journals
Abstract
Utilization of Industrial waste, construction waste, agriculture waste, commercial waste etc... In concrete plays a vital role in minimizing the disposal problems. Over 300 million tons of industrial wastes are being produced per annum by chemical and agricultural process in India. These materials poses problems of disposal, health hazards and aesthetic problem. Hypo Sludge (HS) is a waste material produced from paper industry that can used as a cement replacement material in concrete since the lime content in the sludge is large. Copper slag is a waste material produced from copper manufacturing process and this can be used as a replacement material for fine aggregate (sand) since the particle size similar to sand. During the present study, an attempt had been made to study the mechanical properties of concrete in which Hypo sludge and Copper slag were as a replacement material for cement and fine aggregate respectively. Replacement percentage used during this study were 10%, 20% and 30% of Hypo sludge for cement. Fine aggregate was replaced with 30%, 40% and 50% of Copper slag. Compressive strength of cubes were found on 7th, 28th and 56th days. Split tensile strengths of the cylinders were found on 28th and 56th days. Flexural strengths of prism specimens were found on 28th day. It has been found that usage of Hypo sludge and Copper slag as a replacement material has beneficial effects on the Mechanical properties of concrete.
Keywords: Hypo sludge, Copper slag, Compressive strength, Split tensile strength, Flexural strength.
STUDY ON GEOPOLYMER CONCRETE USED FOR PAVING BLOCKSAM Publications
Paver block is used in various applications like in street road and other construction places. Portland cement generates large amounts of carbon dioxide (CO2) which is responsible for global warming hence it is a greenhouse gas. And the concrete paver block production consume large amount of water and space for curing purpose. The other great problem today is disposal of solid waste from Coal fired thermal power plants generate fly ash and pond ash. This project combined sustainability, curing free with waste management leading to a wonderful product called geo-polymer concrete pavers. This paper represents the results of the geopolymer concrete paver block with the mix of M40 grade Test results indicate that low calcium fly ash based geopolymer concrete pavers has excellent compressive strength within short period (3 days) without water curing & suitable for practical applications
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
A PARAMETRIC STUDY ON EFFECT OF FLY ASH TOGETHER WITH FIBER FOR SUSTAINABLE C...IAEME Publication
The present challenge for civil engineers is to produce high volume and high
performance fly ash concrete with increased durability and service life, at lowest
possible cost. Also concrete produced should have minimal negative impact on the
environment, which is green and sustainable concrete. This can be achieved by
reducing the use of natural lime, fine and coarse aggregates whose resources are
limited and are depleting very fast day by day. It could also be achieved by utilizing
maximum possible industrial by-product like fly ash in concrete as it would reduce
landfill area for fly ash disposal and CO2 emission during cement manufacturing
process. Effect of fly ash as replacement of cement together with fibers in concrete on
durability is very well reported in literatures. However effect of fly ash as partial
replacement of cement and sand together with fibers is not clearly available in
literatures. Literatures show that partial replacement of cement by fly ash reduces early
age strength of concrete. Partial replacement of sand by fly ash together with fiber shall
compensate strength loss due to partial replacement of cement by fly ash. Due to
government restrictions on natural sand mining from river beds, contractors are
demanding a reliable and all weather partial or full replacement material for sand.
Present study shall be a right step forward in reducing consumption of natural sand
and consuming higher volumes of fly ash available in Chhattisgarh region together with
fibers for sustainable and durable concrete.
Experimental Investigations of Mechanical properties on Micro silica (Silica ...IOSR Journals
Abstract : The Now a day, we need to look at a way to reduce the cost of building materials, particularly
cement is currently so high that only rich people and governments can afford meaningful construction. Studies
have been carried out to investigate the possibility of utilizing a broad range of materials as partial replacement
materials for cement in the production of concrete. This study investigated the strength properties of Silica fume
and fly ash concrete. This work primarily deals with the strength characteristics such as compressive, Split
tensile and flexural strength. High performance concrete a set of 7 different concrete mixture were cast and
tested with different cement replacement levels (0%, 2.5%, 5%, 7.5%, 10% 12.5% and15%) of Fly ash (FA) with
silica fume (SF) as addition ( 0%,5%,10 % ,15% ,25and 30%) by wt of Cement and/or each trial super
plasticizer has been added at constant values to achieve a constant range of slump for desired work ability with
a constant water-binder (w/b) ratio of 0.30.Specimens were produced and cured in a curing tank for 3, 7, 14
and 28 days. The cubes were subjected to compressive strength tests after density determination at 3,7,14 and
28 days respectively. The chemical composition and physical composition of micro silica, FlyAsh and cement
were determined. The density of the concrete decreased with increased in percentage of micro silica and Fly ash
replacement up to 15%. Increase in the level of micro silica fume and Fly ash replacement between 30% to 45%
led to a reduction in the compressive strength of hardened concrete. This study has shown that between 15 to
22.5% replacement levels, concrete will develop strength sufficient for construction purposes. Its use will lead
to a reduction in cement quantity required for construction purposes and hence sustainability in the
construction industry as well as aid economic construction.
Keywords: Durability, Fly Ash, High performance Concrete, Silica Fume/Micro Silica, Density, water
absorption
Variation of Compressive strength and water absorption of concrete made by Tw...ijsrd.com
Nowadays construction materials are increasingly evaluated by their ecological characteristics. Concrete recycling gains importance because it protects natural resources and eliminates the need for disposal by using the readily available concrete as an aggregate source for new concrete or other applications. The concrete in this paper is produced by utilizing alternative and recycled waste materials such as fly ash and recycled concrete aggregates to reduce energy consumption, environmental impact, and usage of natural resources. The inferior quality of recycled aggregate (RA) has restricted its use to low-grade applications such as roadwork sub-base and pavements, while its adoption for higher-grade concrete is rare because of the lower compressive strength and higher variability in mechanical performance of RA. A new concrete mixing method, two-stage mixing approach (TSMA), was advocated to improve the quality of RA concrete (RAC) by splitting the mixing process into two parts. In the current paper we will discuss two parameters on which the concrete made by TSMA has been tested for strength characteristics viz. compressive strength and flexural strength. These parametric properties are compared with the conventional concrete with the variation of percentage of recycled coarse aggregates(RCA) and fly ash.
DESIGN OF RIGID PAVEMENT AND ITS COST-BENEFIT ANALYSIS BY USAGE OF VITRIFIED ...IAEME Publication
A country can achieve sustainable and rapid growth in all fields by improving its connectivity and transit systems. Connectivity of people to resources by improved transit mechanism results in improved living standards. Apart from other means, the major part of connectivity of any country is through road systems. Well designed and maintained pavements provide better and long lasting service. In India, all the major road systems are designed as flexible pavements only, because of their ease of construction and less time it takes to be opened to traffic operations. The major problem with flexible pavements is their design life and high maintenance costs. Also, globally reducing petrol reserves, which are used for bitumen and asphalt production are also increasing the need for alternatives. To tackle these problems, rigid pavements can be constructed. Although the cost of construction of rigid pavements is high, its long life, high load carrying capabilities and low maintenance cost will balance the initial cost aspect. Recently, many studies are being conducted on different pozzolanic admixtures which can be used as partial replacement of cement in rigid pavements, thereby reducing its cost and enhancing properties of the mix. Here, an attempt is made to reduce the construction cost of rigid pavements by incorporating Vitrified Polish Waste (VPW) as partial cement replacement in proportions of 5% for M40 grade concrete. Further, to enhance flexural properties of pavement, Recron fibre is added to optimum VPW in increments of 0.1%, then after C.C pavement is designed for two lane two way national highway and cost benefit analysis is performed.
Explore the innovative world of trenchless pipe repair with our comprehensive guide, "The Benefits and Techniques of Trenchless Pipe Repair." This document delves into the modern methods of repairing underground pipes without the need for extensive excavation, highlighting the numerous advantages and the latest techniques used in the industry.
Learn about the cost savings, reduced environmental impact, and minimal disruption associated with trenchless technology. Discover detailed explanations of popular techniques such as pipe bursting, cured-in-place pipe (CIPP) lining, and directional drilling. Understand how these methods can be applied to various types of infrastructure, from residential plumbing to large-scale municipal systems.
Ideal for homeowners, contractors, engineers, and anyone interested in modern plumbing solutions, this guide provides valuable insights into why trenchless pipe repair is becoming the preferred choice for pipe rehabilitation. Stay informed about the latest advancements and best practices in the field.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.