This document describes an automated energy monitoring system and power factor improvement project. The system continuously monitors the power factor of an electrical load and automatically improves it using a capacitor bank. It measures the reactive power consumed by inductive loads and compensates for the lagging power factor. This correction brings the power factor closer to unity, providing benefits like reduced power losses, increased system capacity, and improved voltages. The system uses current and potential transformers to monitor voltage and current. A microcontroller then calculates the power factor and controls relays to switch capacitors on or off as needed to improve the overall power factor.
IRJET-Management of power factor and harmonicIRJET Journal
P. K. Kurundwade, G. V. Swami , R. A. Metri, S. B. Patil, P. B. Patil, M. Patil "Management of power factor and harmonic", International Research Journal of Engineering and Technology (IRJET), Volume2,issue-01 April 2015.e-ISSN:2395-0056, p-ISSN:2395-0072. www.irjet.net
Abstract
This paper discusses about the power factor improvement and reduction in harmonic system. Poor power factor causes increased electricity charges, penalty for low power factor and unnecessary effect in the system and poor power quality. To smooth such negative effects, the power factor correction is carried out, also reduce harmonic content in the system filters are used. Automatic Power Factor Correction relay is one of the smart relay used to control the capacitor with respect to output. The proposed system is characterized by no generation of harmonics and reduction of transmission losses.
Power factor improvement is the essence of any power sector for realible operations. This report provides literature study of a fixed capacitor thyristor controlled reactor type of power factor compensator by matlab simulation and implementation in programmed microcontroller. To retaining power factor closed to unity under various load condition the arduino ATmega8 microcontroller is used which is programmed by keil software. The simulation is done using proteus software which display power factor according to the variation in load whenever a capacitive load is connected to the transmission line, a shunt reactor is connected which injects lagging reactive VARs to the power system. This report also includes the matlab simulation for three phase power factor improvement by using fixed capacitor thyristor controlled reactor. As a
result the power factor is improved. The results given in this report provides
suitable matlab simulation and proteus simulation based reactor power compensation and power factor improvement and techniques using a FCTCR.
The proposed model automatically corrects the power factor without any human presence. It consist of a micro controller which detects the power factor value,if the power factor goes low during peak hours it automatically connects capacitor banks to improve it. The main aim of the model is to maintain the power factor as high as possible which helps to increase the efficiency of the system.
IRJET-Management of power factor and harmonicIRJET Journal
P. K. Kurundwade, G. V. Swami , R. A. Metri, S. B. Patil, P. B. Patil, M. Patil "Management of power factor and harmonic", International Research Journal of Engineering and Technology (IRJET), Volume2,issue-01 April 2015.e-ISSN:2395-0056, p-ISSN:2395-0072. www.irjet.net
Abstract
This paper discusses about the power factor improvement and reduction in harmonic system. Poor power factor causes increased electricity charges, penalty for low power factor and unnecessary effect in the system and poor power quality. To smooth such negative effects, the power factor correction is carried out, also reduce harmonic content in the system filters are used. Automatic Power Factor Correction relay is one of the smart relay used to control the capacitor with respect to output. The proposed system is characterized by no generation of harmonics and reduction of transmission losses.
Power factor improvement is the essence of any power sector for realible operations. This report provides literature study of a fixed capacitor thyristor controlled reactor type of power factor compensator by matlab simulation and implementation in programmed microcontroller. To retaining power factor closed to unity under various load condition the arduino ATmega8 microcontroller is used which is programmed by keil software. The simulation is done using proteus software which display power factor according to the variation in load whenever a capacitive load is connected to the transmission line, a shunt reactor is connected which injects lagging reactive VARs to the power system. This report also includes the matlab simulation for three phase power factor improvement by using fixed capacitor thyristor controlled reactor. As a
result the power factor is improved. The results given in this report provides
suitable matlab simulation and proteus simulation based reactor power compensation and power factor improvement and techniques using a FCTCR.
The proposed model automatically corrects the power factor without any human presence. It consist of a micro controller which detects the power factor value,if the power factor goes low during peak hours it automatically connects capacitor banks to improve it. The main aim of the model is to maintain the power factor as high as possible which helps to increase the efficiency of the system.
Design of UPQC with Minimization of DC Link voltage for the Improvement of Po...IDES Editor
Devices such as power electronics converters, inject
harmonic currents in the AC system and increase overall
reactive power demanded by the equivalent loads are presents
non-linear characteristics. Also, the number of sensitive loads
that require ideal sinusoidal supply voltages for their proper
operation has increased. In order to keep power quality under
limits proposed by standards, it is necessary to include some
sort of compensation. The aim of this paper is to present a
unified power quality conditioner (UPQC) with minimization
of DC Link voltage for the improvement of power quality by
Fuzzy logic controller as compared with PI controller. By the
proposed system is comprised of series and shunt Inverters
which can compensate the sag, swell, unbalance voltage,
Harmonics and reactive power. PI and fuzzy logic controllers
are used to stabilize DC link voltage and balance the active
power between shunt and series inverters for the enhancement
of power quality.
Adaptive Modified Minimally Switched Hysteresis Controlled Shunt Active Power...idescitation
The main focus of this article is to investigate the
effects of Adaptive control on the switching frequency and
Total Harmonic Distortion of a modified, minimally switched
hysteresis controlled shunt active power filter. Reference
current generation was done using Instantaneous real and
reactive power algorithm. Pulses to the minimally switched
grid interactive inverter in which only two switches are
controlled at a time, had been generated using a modified
hysteresis current controller. Use of Modified Hysteresis
controller results in reducing the switching loses to one-third
but results in increase in current THD than the conventional
hysteresis controller. To overcome this, pulses to the modified
hysteresis controller were generated employing adaptive
control by modifying pulses from a conventional hysteresis
controller. Using adaptive control instantaneous switching
frequency was reduced and maintained nearly constant and
THD was brought to the limits specified by the standards,
thus overcoming the disadvantage of conventional and modified
hysteresis controller which has variable switching frequency.
A comparison of Modified Hysteresis controller with and
without Adaptive control has been made, to show the reduction
in THD. The system was simulated using MATLAB-
SIMULINK.
SIMULATION OF REDUCED SWITCH INVERTER BASED UPQC WITH FUZZY LOGIC AND ANN CON...MABUSUBANI SHAIK
ABSTRACT
This paper presents a new methodology to reduce harmonic distortion in UPQC using artificial neural network
and fuzzy logic controller. So this paper main aim is improve power quality by using UPQC with ANN and FLC. The most purpose of the proposed (ANN & FLC) is capable of providing good static and dynamic performances compared to PI controller. The UPQC is to control on voltage flicker/unbalance, reactive power and harmonics. In different words, the UPQC has the potential of up power quality at the purpose of installation on power industrial power systems. The appliance of computing is growing quick within the space of power electronics and drives. From olden days to now days we are using twelve switches used in back to back configuration. But now we are using nine switches instead of 12
switches. In 9 switch UPQC converter given the most useful benefits compared to 12 switches power converter. The nine switches UPQC converter gets the best results by using of three methods. They are one is PI controller technique, ANN controller technique and FLC controller technique. By contrast PI, FLC and ANN, ANN is better than (FLC & PI) for power quality enhancement and voltage sag and voltage swell mitigations. The factitious neural network (ANN) is taken into account as a replacement tool to style management electronic equipment for power quality (PQ) devices. A whole
simulation study is administrated to analysis the performance of the ANN controller and compares its performance with the quality FLC & PI controller’s results. The nine-switch convertor has already been proved to possess sure benefits,
additionally to its part saving topological feature. Despite these benefits, the nine-switch convertor has thus far found restricted applications because of its several perceived performance tradeoffs like requiring associate degree outsized
dc-link capacitance, restricted amplitude sharing, and unnatural part shift between its 2 sets of output terminals. Rather than acceptive these tradeoffs as limitations, a nine-switch power conditioner is projected here that nearly “converts” most of those topological short comings into fascinating performance benefits. Aiming more to cut back its switch losses,
Harmonics, Voltage Sag & Swell associate degree acceptable discontinuous modulation theme is projected and studied here thoroughly to doubly make sure that top reduction of commutations is achieved. With associate degree suitably
designed management theme with PI and ANN with Fuzzy logic controller then incorporated, the nine-switch convertor is shown to favorably raise the general power quality in Simulation, thus justifying its role as an influence conditioner at a reduced value.
KEYWORDS: ANN, Active Power Filters, PI Controller, Nine Switch Converter, Power Quality, UPQC
Power quality improvement using upqc with soft computing method: Fuzzy logicSakti Prasanna Muduli
Now a days problems regarding power quality is more in large inter connected power systems. There are many method to mitigate these problems but using the latest most efficient compensation method is some what impressive. Here is the brief explanations regarding UPQC using soft computing method(fuzzy logic). This was my academic project along with my friends.
SRF THEORY BASED STATCOM FOR COMPENSATION OF REACTIVE POWER AND HARMONICSIAEME Publication
The power electronic devices like converters and inverters inject harmonic currents into AC
system due to their non linear characteristics. These devices draw high amount of reactive power
from source. The commencement of Nonlinear Load into the ac power system will have the effect of
harmonics. The presence of harmonics in system it will effected with power quality problems. Due
to this high amount of power losses and disoperation of power electronics devices is caused, along
with this Harmonics have a number of undesirable effects like Voltage disturbances. These
harmonics are needed to mitigate for Power Quality Enhancement in distributed system. Here the
device called STATCOM is one of the FACTS Devices which can be used to mitigate the harmonics
and reactive power compensation. The voltage source converter is core of the STATCOM and the
hysteresis current control is indirect method of controlling of VSC. In this paper we implement with
SRF based STATCOM control. SRF theory is implemented for the generation of controlling
reference current signals for controller of STATCOM. The Matlab\Simulink based model is
developed and simulation results are showed for linear and nonlinear load conditions.
The use of distributed generation (DG) within distribution systems has increased for the last two decades due to worldwide increase in demand for electricity and governmental policy change from “conventional” energy to “green” energy. High levels of penetration of DG have many significant benefits but also come with many drawbacks such as voltage drop and power losses. This study presents the impact of DG at different locations in a distribution feeder in terms of the feeder voltage profile. A radial distribution system is simulated using PSCAD/EMTDC simulation software while changing the size and location of DG in the system. The obtained results are used for better understanding on the impact of DG on voltage profile in radial distribution feeder.
Grid Interconnection of Renewable Energy Sources at the Distribution Level Wi...Pradeep Avanigadda
Renewable energy resources (RES) are being increasingly connected in distribution systems utilizing power electronic converters.
This project presents a novel control strategy for achieving maximum benefits from these grid-interfacing inverters when installed in 3-phase 4-wire distribution systems.
The inverter can thus be utilized as:
1) power converter to inject power generated from RES to the grid &
2) shunt APF to compensate current unbalance, load current harmonics, load reactive power demand and load neutral current.
This paper focus on distribution system by applying different control techniques in order to improve the performance of the system. In the distribution system mainly concentrate on power quality issues like reactive power control, harmonic elimination, power factor correction, etc. Because of power quality problems voltage, current, frequency are continuously changing in power systems. These changes will effects the performance of power systems. Power quality problems can be compensated by placing DSTATCOM which is connected at PCC in parallel. It is shunt connected VSI along with the filters, with the help of DSTATCOM voltage sag, swell and THD can be controlled. This paper presents detailed explanation about performance and configuration of latest control techniques to control the DSTATCOM.
Optimization Technique for Power Quality Improvement using DSTATCOM Neural Ne...ijtsrd
As the power demand has been increasing rapidly, power generation and transmission are being affected due to limited resources, environmental restrictions and other losses. soft computing the techniques of correcting the supply voltage sag, swell and interruption in a distributed system. At present, a wide range of very flexible controllers, which capitalize on newly available power electronics components, are emerging for custom power applications. Power electronic based equipment aimed at enhancing the reliability and quality of power flows in low voltage distribution networks. A control algorithm is used for the extraction of the fundamental weighted value of active and reactive power components. Using digital signal processor the DSTATCOM is developed and its performance of DSTATCOM is found to be satisfactory for various types of loads. Hareram Mishra | Manju Gupta | Dr. Anuprita Mishra "Optimization Technique for Power Quality Improvement using DSTATCOM (Neural Network Approach) – A Review" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-5 | Issue-5 , August 2021, URL: https://www.ijtsrd.com/papers/ijtsrd45219.pdf Paper URL: https://www.ijtsrd.com/engineering/other/45219/optimization-technique-for-power-quality-improvement-using-dstatcom-neural-network-approach- – -a-review/hareram-mishra
Design of UPQC with Minimization of DC Link voltage for the Improvement of Po...IDES Editor
Devices such as power electronics converters, inject
harmonic currents in the AC system and increase overall
reactive power demanded by the equivalent loads are presents
non-linear characteristics. Also, the number of sensitive loads
that require ideal sinusoidal supply voltages for their proper
operation has increased. In order to keep power quality under
limits proposed by standards, it is necessary to include some
sort of compensation. The aim of this paper is to present a
unified power quality conditioner (UPQC) with minimization
of DC Link voltage for the improvement of power quality by
Fuzzy logic controller as compared with PI controller. By the
proposed system is comprised of series and shunt Inverters
which can compensate the sag, swell, unbalance voltage,
Harmonics and reactive power. PI and fuzzy logic controllers
are used to stabilize DC link voltage and balance the active
power between shunt and series inverters for the enhancement
of power quality.
Adaptive Modified Minimally Switched Hysteresis Controlled Shunt Active Power...idescitation
The main focus of this article is to investigate the
effects of Adaptive control on the switching frequency and
Total Harmonic Distortion of a modified, minimally switched
hysteresis controlled shunt active power filter. Reference
current generation was done using Instantaneous real and
reactive power algorithm. Pulses to the minimally switched
grid interactive inverter in which only two switches are
controlled at a time, had been generated using a modified
hysteresis current controller. Use of Modified Hysteresis
controller results in reducing the switching loses to one-third
but results in increase in current THD than the conventional
hysteresis controller. To overcome this, pulses to the modified
hysteresis controller were generated employing adaptive
control by modifying pulses from a conventional hysteresis
controller. Using adaptive control instantaneous switching
frequency was reduced and maintained nearly constant and
THD was brought to the limits specified by the standards,
thus overcoming the disadvantage of conventional and modified
hysteresis controller which has variable switching frequency.
A comparison of Modified Hysteresis controller with and
without Adaptive control has been made, to show the reduction
in THD. The system was simulated using MATLAB-
SIMULINK.
SIMULATION OF REDUCED SWITCH INVERTER BASED UPQC WITH FUZZY LOGIC AND ANN CON...MABUSUBANI SHAIK
ABSTRACT
This paper presents a new methodology to reduce harmonic distortion in UPQC using artificial neural network
and fuzzy logic controller. So this paper main aim is improve power quality by using UPQC with ANN and FLC. The most purpose of the proposed (ANN & FLC) is capable of providing good static and dynamic performances compared to PI controller. The UPQC is to control on voltage flicker/unbalance, reactive power and harmonics. In different words, the UPQC has the potential of up power quality at the purpose of installation on power industrial power systems. The appliance of computing is growing quick within the space of power electronics and drives. From olden days to now days we are using twelve switches used in back to back configuration. But now we are using nine switches instead of 12
switches. In 9 switch UPQC converter given the most useful benefits compared to 12 switches power converter. The nine switches UPQC converter gets the best results by using of three methods. They are one is PI controller technique, ANN controller technique and FLC controller technique. By contrast PI, FLC and ANN, ANN is better than (FLC & PI) for power quality enhancement and voltage sag and voltage swell mitigations. The factitious neural network (ANN) is taken into account as a replacement tool to style management electronic equipment for power quality (PQ) devices. A whole
simulation study is administrated to analysis the performance of the ANN controller and compares its performance with the quality FLC & PI controller’s results. The nine-switch convertor has already been proved to possess sure benefits,
additionally to its part saving topological feature. Despite these benefits, the nine-switch convertor has thus far found restricted applications because of its several perceived performance tradeoffs like requiring associate degree outsized
dc-link capacitance, restricted amplitude sharing, and unnatural part shift between its 2 sets of output terminals. Rather than acceptive these tradeoffs as limitations, a nine-switch power conditioner is projected here that nearly “converts” most of those topological short comings into fascinating performance benefits. Aiming more to cut back its switch losses,
Harmonics, Voltage Sag & Swell associate degree acceptable discontinuous modulation theme is projected and studied here thoroughly to doubly make sure that top reduction of commutations is achieved. With associate degree suitably
designed management theme with PI and ANN with Fuzzy logic controller then incorporated, the nine-switch convertor is shown to favorably raise the general power quality in Simulation, thus justifying its role as an influence conditioner at a reduced value.
KEYWORDS: ANN, Active Power Filters, PI Controller, Nine Switch Converter, Power Quality, UPQC
Power quality improvement using upqc with soft computing method: Fuzzy logicSakti Prasanna Muduli
Now a days problems regarding power quality is more in large inter connected power systems. There are many method to mitigate these problems but using the latest most efficient compensation method is some what impressive. Here is the brief explanations regarding UPQC using soft computing method(fuzzy logic). This was my academic project along with my friends.
SRF THEORY BASED STATCOM FOR COMPENSATION OF REACTIVE POWER AND HARMONICSIAEME Publication
The power electronic devices like converters and inverters inject harmonic currents into AC
system due to their non linear characteristics. These devices draw high amount of reactive power
from source. The commencement of Nonlinear Load into the ac power system will have the effect of
harmonics. The presence of harmonics in system it will effected with power quality problems. Due
to this high amount of power losses and disoperation of power electronics devices is caused, along
with this Harmonics have a number of undesirable effects like Voltage disturbances. These
harmonics are needed to mitigate for Power Quality Enhancement in distributed system. Here the
device called STATCOM is one of the FACTS Devices which can be used to mitigate the harmonics
and reactive power compensation. The voltage source converter is core of the STATCOM and the
hysteresis current control is indirect method of controlling of VSC. In this paper we implement with
SRF based STATCOM control. SRF theory is implemented for the generation of controlling
reference current signals for controller of STATCOM. The Matlab\Simulink based model is
developed and simulation results are showed for linear and nonlinear load conditions.
The use of distributed generation (DG) within distribution systems has increased for the last two decades due to worldwide increase in demand for electricity and governmental policy change from “conventional” energy to “green” energy. High levels of penetration of DG have many significant benefits but also come with many drawbacks such as voltage drop and power losses. This study presents the impact of DG at different locations in a distribution feeder in terms of the feeder voltage profile. A radial distribution system is simulated using PSCAD/EMTDC simulation software while changing the size and location of DG in the system. The obtained results are used for better understanding on the impact of DG on voltage profile in radial distribution feeder.
Grid Interconnection of Renewable Energy Sources at the Distribution Level Wi...Pradeep Avanigadda
Renewable energy resources (RES) are being increasingly connected in distribution systems utilizing power electronic converters.
This project presents a novel control strategy for achieving maximum benefits from these grid-interfacing inverters when installed in 3-phase 4-wire distribution systems.
The inverter can thus be utilized as:
1) power converter to inject power generated from RES to the grid &
2) shunt APF to compensate current unbalance, load current harmonics, load reactive power demand and load neutral current.
This paper focus on distribution system by applying different control techniques in order to improve the performance of the system. In the distribution system mainly concentrate on power quality issues like reactive power control, harmonic elimination, power factor correction, etc. Because of power quality problems voltage, current, frequency are continuously changing in power systems. These changes will effects the performance of power systems. Power quality problems can be compensated by placing DSTATCOM which is connected at PCC in parallel. It is shunt connected VSI along with the filters, with the help of DSTATCOM voltage sag, swell and THD can be controlled. This paper presents detailed explanation about performance and configuration of latest control techniques to control the DSTATCOM.
Optimization Technique for Power Quality Improvement using DSTATCOM Neural Ne...ijtsrd
As the power demand has been increasing rapidly, power generation and transmission are being affected due to limited resources, environmental restrictions and other losses. soft computing the techniques of correcting the supply voltage sag, swell and interruption in a distributed system. At present, a wide range of very flexible controllers, which capitalize on newly available power electronics components, are emerging for custom power applications. Power electronic based equipment aimed at enhancing the reliability and quality of power flows in low voltage distribution networks. A control algorithm is used for the extraction of the fundamental weighted value of active and reactive power components. Using digital signal processor the DSTATCOM is developed and its performance of DSTATCOM is found to be satisfactory for various types of loads. Hareram Mishra | Manju Gupta | Dr. Anuprita Mishra "Optimization Technique for Power Quality Improvement using DSTATCOM (Neural Network Approach) – A Review" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-5 | Issue-5 , August 2021, URL: https://www.ijtsrd.com/papers/ijtsrd45219.pdf Paper URL: https://www.ijtsrd.com/engineering/other/45219/optimization-technique-for-power-quality-improvement-using-dstatcom-neural-network-approach- – -a-review/hareram-mishra
A Review on Optimization Techniques for Power Quality Improvement using DSTAT...ijtsrd
As demand for electricity has risen exponentially, power production and transmission are affected by scarce energy, environmental constraints and other losses. Soft computing methods to fix the sag, swell and disruption of the supply voltage in the distributed device. At present, a broad variety of highly versatile controls that leverage on newly available power electronics components are evolving for custom power applications. Control electronic equipment intended to improve the stability and efficiency of electricity flows in low voltage distribution networks. The control algorithm is used to derive the fundamental weighted value of the active and reactive power components. Using a digital signal processor, DSTATCOM is built and its output as a DSTATCOM is found to be satisfactory for different types of loads. Amit Radhakrishna Parhad | Pramod Kumar Rathore "A Review on Optimization Techniques for Power Quality Improvement using DSTATCOM (Neural Network Approach)" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-5 | Issue-4 , June 2021, URL: https://www.ijtsrd.compapers/ijtsrd42403.pdf Paper URL: https://www.ijtsrd.comengineering/electrical-engineering/42403/a-review-on-optimization-techniques-for-power-quality-improvement-using-dstatcom-neural-network-approach/amit-radhakrishna-parhad
Hardware Implementation of Single Phase Power Factor Correction System using ...IAES-IJPEDS
Rapid increase of consumers in electronics devices and the use of mains rectification circuits inside these electronic devices is the root cause of mains harmonic distortion. Automatic power factor correction techniques can be applied to the industries, power systems and households to make them stable inturns increases the efficiency of system as well as the apparatus. This paper deals with the hardware design of active power factor correction circuit employing boost converter which is used to boost the DC voltages with a controller based on PID control strategy. The pulses given to power switches by pulse width modulation techniques generated by utilizing micro-controller board, Arduino thus obviating the need of complex hardware circuitry. MATLAB/SIMULINK was used to design and tune the PID controller parameters. The simulation results are matching with the predictions and the same was implemented as hardware. The waveforms various test points and across capacitors were obtained, studied and compared with the theoretical waveforms and are found to be in precise proximity of theoretical waveforms.
Simulation and Analysis of a D-STATCOM for Load Compensation and Power Facto...IJMER
Power Generation and Transmission is a complex process, requiring the working of many
components of the power system in tandem to maximize the output. One of the main components to form
a major part is the reactive power in the system. It is required to maintain the voltage to deliver the
active power through the lines. Loads like motor loads and other loads require reactive power for their
operation. To improve the performance of ac power systems, we need to manage this reactive power in
an efficient way and this is known as reactive power compensation. In developing countries like India,
where the variation of power frequency and many such other determinants of power quality are
themselves a serious question, it is very vital to take positive steps in this direction.
The work presented here illustrates a method to compensate for the load reactive power using a
DSTATCOM
A DSTATCOM injects a current into the system to provide for the reactive component of the load
current. The validity of proposed method and achievement of desired compensation are confirmed by
the results of the simulation in MATLAB/ Simulink.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Similar to IRJET- Automated Energy Monitering System and Power Factor Improvement (20)
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
Explore the innovative world of trenchless pipe repair with our comprehensive guide, "The Benefits and Techniques of Trenchless Pipe Repair." This document delves into the modern methods of repairing underground pipes without the need for extensive excavation, highlighting the numerous advantages and the latest techniques used in the industry.
Learn about the cost savings, reduced environmental impact, and minimal disruption associated with trenchless technology. Discover detailed explanations of popular techniques such as pipe bursting, cured-in-place pipe (CIPP) lining, and directional drilling. Understand how these methods can be applied to various types of infrastructure, from residential plumbing to large-scale municipal systems.
Ideal for homeowners, contractors, engineers, and anyone interested in modern plumbing solutions, this guide provides valuable insights into why trenchless pipe repair is becoming the preferred choice for pipe rehabilitation. Stay informed about the latest advancements and best practices in the field.
CFD Simulation of By-pass Flow in a HRSG module by R&R Consult.pptxR&R Consult
CFD analysis is incredibly effective at solving mysteries and improving the performance of complex systems!
Here's a great example: At a large natural gas-fired power plant, where they use waste heat to generate steam and energy, they were puzzled that their boiler wasn't producing as much steam as expected.
R&R and Tetra Engineering Group Inc. were asked to solve the issue with reduced steam production.
An inspection had shown that a significant amount of hot flue gas was bypassing the boiler tubes, where the heat was supposed to be transferred.
R&R Consult conducted a CFD analysis, which revealed that 6.3% of the flue gas was bypassing the boiler tubes without transferring heat. The analysis also showed that the flue gas was instead being directed along the sides of the boiler and between the modules that were supposed to capture the heat. This was the cause of the reduced performance.
Based on our results, Tetra Engineering installed covering plates to reduce the bypass flow. This improved the boiler's performance and increased electricity production.
It is always satisfying when we can help solve complex challenges like this. Do your systems also need a check-up or optimization? Give us a call!
Work done in cooperation with James Malloy and David Moelling from Tetra Engineering.
More examples of our work https://www.r-r-consult.dk/en/cases-en/
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.