The document compares two control algorithms, back propagation and synchronous reference frame theory, for controlling a DSTATCOM (dynamic voltage compensator) to compensate for reactive power and eliminate current harmonics from linear and non-linear loads. It simulates the DSTATCOM performance with each control algorithm under different load conditions. The back propagation algorithm uses load current measurements to estimate reference source currents, while synchronous reference frame theory transforms load currents between stationary and rotating coordinate systems to extract reference values. Simulation results show that with both control algorithms, the DSTATCOM is able to regulate voltage amplitude at the point of common coupling and reduce total harmonic distortion of source currents from non-linear loads.
International Journal of Engineering Research and Development is an international premier peer reviewed open access engineering and technology journal promoting the discovery, innovation, advancement and dissemination of basic and transitional knowledge in engineering, technology and related disciplines.
We follow "Rigorous Publication" model - means that all articles appear on IJERD after full appraisal, effectiveness, legitimacy and reliability of research content. International Journal of Engineering Research and Development publishes papers online as well as provide hard copy of Journal to authors after publication of paper. It is intended to serve as a forum for researchers, practitioners and developers to exchange ideas and results for the advancement of Engineering & Technology.
A Voltage Controlled Dstatcom for Power Quality Improvementiosrjce
Due to increasing complexity in the power system, voltage sag is becoming one of the most significant
power quality problems. Voltage sag is a short reduction voltage from nominal voltage, occurs in a short time.
If the voltage sags exceed two to three cycles, then manufacturing systems making use of sensitive electronic
equipments are likely to be affected leading to major problems. It ultimately leads to wastage of resources (both
material and human) as well as financial losses. This is possible only by ensuring that uninterrupted flow of
power is maintained at proper voltage levels. This project tends look at the solving the sag problems by using
custom power devices such as Distribution Static compensator (D-STATCOM).Proposed scheme follows a new
algorithm to generate reference voltage for a distribution static compensator (DSTATCOM) operating in
voltage-control mode. The proposed scheme ensures that unity power factor (UPF) is achieved at the load
terminal during nominal operation, which is not possible in the traditional method. Also, the compensator
injects lower currents therefore, reduces losses in the feeder and voltage-source inverter. Further, a saving in
the rating of DSTATCOM is achieved which increases its capacity to mitigate voltage sag. Nearly UPF is
maintained, while regulating voltage at the load terminal, during load change. The state-space model of
DSTATCOM is incorporated with the deadbeat predictive controller for fast load voltage regulation during
voltage disturbances. With these features, this scheme allows DSTATCOM to tackle power-quality issues by
providing power factor correction, harmonic elimination, load balancing, and voltage regulation based on the
load requirement.
International Journal of Engineering Research and Development is an international premier peer reviewed open access engineering and technology journal promoting the discovery, innovation, advancement and dissemination of basic and transitional knowledge in engineering, technology and related disciplines.
We follow "Rigorous Publication" model - means that all articles appear on IJERD after full appraisal, effectiveness, legitimacy and reliability of research content. International Journal of Engineering Research and Development publishes papers online as well as provide hard copy of Journal to authors after publication of paper. It is intended to serve as a forum for researchers, practitioners and developers to exchange ideas and results for the advancement of Engineering & Technology.
A Voltage Controlled Dstatcom for Power Quality Improvementiosrjce
Due to increasing complexity in the power system, voltage sag is becoming one of the most significant
power quality problems. Voltage sag is a short reduction voltage from nominal voltage, occurs in a short time.
If the voltage sags exceed two to three cycles, then manufacturing systems making use of sensitive electronic
equipments are likely to be affected leading to major problems. It ultimately leads to wastage of resources (both
material and human) as well as financial losses. This is possible only by ensuring that uninterrupted flow of
power is maintained at proper voltage levels. This project tends look at the solving the sag problems by using
custom power devices such as Distribution Static compensator (D-STATCOM).Proposed scheme follows a new
algorithm to generate reference voltage for a distribution static compensator (DSTATCOM) operating in
voltage-control mode. The proposed scheme ensures that unity power factor (UPF) is achieved at the load
terminal during nominal operation, which is not possible in the traditional method. Also, the compensator
injects lower currents therefore, reduces losses in the feeder and voltage-source inverter. Further, a saving in
the rating of DSTATCOM is achieved which increases its capacity to mitigate voltage sag. Nearly UPF is
maintained, while regulating voltage at the load terminal, during load change. The state-space model of
DSTATCOM is incorporated with the deadbeat predictive controller for fast load voltage regulation during
voltage disturbances. With these features, this scheme allows DSTATCOM to tackle power-quality issues by
providing power factor correction, harmonic elimination, load balancing, and voltage regulation based on the
load requirement.
A Review on Optimization Techniques for Power Quality Improvement using DSTAT...ijtsrd
As demand for electricity has risen exponentially, power production and transmission are affected by scarce energy, environmental constraints and other losses. Soft computing methods to fix the sag, swell and disruption of the supply voltage in the distributed device. At present, a broad variety of highly versatile controls that leverage on newly available power electronics components are evolving for custom power applications. Control electronic equipment intended to improve the stability and efficiency of electricity flows in low voltage distribution networks. The control algorithm is used to derive the fundamental weighted value of the active and reactive power components. Using a digital signal processor, DSTATCOM is built and its output as a DSTATCOM is found to be satisfactory for different types of loads. Amit Radhakrishna Parhad | Pramod Kumar Rathore "A Review on Optimization Techniques for Power Quality Improvement using DSTATCOM (Neural Network Approach)" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-5 | Issue-4 , June 2021, URL: https://www.ijtsrd.compapers/ijtsrd42403.pdf Paper URL: https://www.ijtsrd.comengineering/electrical-engineering/42403/a-review-on-optimization-techniques-for-power-quality-improvement-using-dstatcom-neural-network-approach/amit-radhakrishna-parhad
The Green Energy sources (solar, wind) are performing a vigorous role to reach the electrical power demand. Due to the presence of non-linear loads, reactive loads in the distribution system and the injection of wind power into the grid integrated system results power quality issues like current harmonics, voltage fluctuations, reactive power demand etc. This paper mainly investigates the designing and satisfactory performance evaluation of solar farm as PV-STATCOM (Static Synchronous Compensator) for enhancement of power quality in grid tie system by using MATLAB environment (Simulink). The proportional and integral (PI) Controller and Hysteresis Current Controller (HCC) were effectively utilized to inject the desired current from voltage source converter (VSC) based PV-STATCOM at PCC for the mitigation of quality related problems in the proposed test system.
SRF CONTROLLED DVR FOR COMPENSATION OF BALANCED AND UNBALANCED VOLTAGE DISTUR...IAEME Publication
The growth of power electronictechnology in the field of electric power sector has caused a greater awarenesson the power quality of distribution systems. With the re-structuring of powersystems and with shifting trend towards distributed and dispersed generation,the issue of power quality is going to take newer dimensions. The presentresearch is to identify the prominent concerns in this area and hence themeasures that can enhance the quality of power. This paper investigates theproblems of voltage sag, swell and its severe impact on nonlinear loads,sensitive loads.
Voltage Sag and Swell Identification Using FFT Analysis and Mitigation with DVRIOSRJEEE
- Power quality issues like voltage sag, swell, harmonics and transients can affect the power system performance. Voltage sag and swell are now-a-days treated to reduce power quality issues by power engineers. A small variation in voltage can badly affect the operation of power system and connected loads as well. This paper presents the voltage sag and voltage swell identification using FFT analysis. The paper also presents the mitigation for identified voltage sag and swells issues addressed with DVR. DVR consists of a voltage source converter and is controlled with d-q theory which is simple producing reference signals and gate pulses for switches of DVR. The proposed concept was simulated using MATLAB/SIMULINK software and results were presented for identification and mitigation. FFT analyses for identification of voltage sags and swell existence in different phases of power system network were shown. Mitigation of voltage sag and swell with DVR was also shown with results
CONTROL OF BATTERY OPERATED SYSTEM WITH A DC-DC BOOSTCONVERTER FED DSTATCOM U...ijiert bestjournal
This paper presents a comprehensive survey of DSTATCOM control strategies put forward recently. It is
aimed at providing a broad perspective on the status of DSTATCOM control methods to researchers and
application engineers dealing with harmonic suppression issues. Many control techniques have been
designed, developed, and realized for active filters in recent years. The proposed DSTATCOM consists of a
three-leg Voltage Source Converter (VSC) with a dc bus capacitor. The PV array or battery operated boost
converter is proposed to maintain the dc link voltage of the dc bus capacitor for continuous compensation
for the load. This paper presents to evaluate the performance comparison of two control strategies for
extracting the reference currents to control the proposed DSTATCOM. The two control methods are
Synchronous Reference Frame (SRF) theory and IcosΦ algorithm. The performance of the DSTATCOM is
validated using MATLAB software with its simulink and Power System Block set (PSB) toolboxes. The
simulation results for the two control methods are compared to validate the superior performance of the
IcosΦ algorithm.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
This paper focus on distribution system by applying different control techniques in order to improve the performance of the system. In the distribution system mainly concentrate on power quality issues like reactive power control, harmonic elimination, power factor correction, etc. Because of power quality problems voltage, current, frequency are continuously changing in power systems. These changes will effects the performance of power systems. Power quality problems can be compensated by placing DSTATCOM which is connected at PCC in parallel. It is shunt connected VSI along with the filters, with the help of DSTATCOM voltage sag, swell and THD can be controlled. This paper presents detailed explanation about performance and configuration of latest control techniques to control the DSTATCOM.
International Journal of Engineering Research and Development is an international premier peer reviewed open access engineering and technology journal promoting the discovery, innovation, advancement and dissemination of basic and transitional knowledge in engineering, technology and related disciplines.
We follow "Rigorous Publication" model - means that all articles appear on IJERD after full appraisal, effectiveness, legitimacy and reliability of research content. International Journal of Engineering Research and Development publishes papers online as well as provide hard copy of Journal to authors after publication of paper. It is intended to serve as a forum for researchers, practitioners and developers to exchange ideas and results for the advancement of Engineering & Technology.
A Review on Optimization Techniques for Power Quality Improvement using DSTAT...ijtsrd
As demand for electricity has risen exponentially, power production and transmission are affected by scarce energy, environmental constraints and other losses. Soft computing methods to fix the sag, swell and disruption of the supply voltage in the distributed device. At present, a broad variety of highly versatile controls that leverage on newly available power electronics components are evolving for custom power applications. Control electronic equipment intended to improve the stability and efficiency of electricity flows in low voltage distribution networks. The control algorithm is used to derive the fundamental weighted value of the active and reactive power components. Using a digital signal processor, DSTATCOM is built and its output as a DSTATCOM is found to be satisfactory for different types of loads. Amit Radhakrishna Parhad | Pramod Kumar Rathore "A Review on Optimization Techniques for Power Quality Improvement using DSTATCOM (Neural Network Approach)" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-5 | Issue-4 , June 2021, URL: https://www.ijtsrd.compapers/ijtsrd42403.pdf Paper URL: https://www.ijtsrd.comengineering/electrical-engineering/42403/a-review-on-optimization-techniques-for-power-quality-improvement-using-dstatcom-neural-network-approach/amit-radhakrishna-parhad
The Green Energy sources (solar, wind) are performing a vigorous role to reach the electrical power demand. Due to the presence of non-linear loads, reactive loads in the distribution system and the injection of wind power into the grid integrated system results power quality issues like current harmonics, voltage fluctuations, reactive power demand etc. This paper mainly investigates the designing and satisfactory performance evaluation of solar farm as PV-STATCOM (Static Synchronous Compensator) for enhancement of power quality in grid tie system by using MATLAB environment (Simulink). The proportional and integral (PI) Controller and Hysteresis Current Controller (HCC) were effectively utilized to inject the desired current from voltage source converter (VSC) based PV-STATCOM at PCC for the mitigation of quality related problems in the proposed test system.
SRF CONTROLLED DVR FOR COMPENSATION OF BALANCED AND UNBALANCED VOLTAGE DISTUR...IAEME Publication
The growth of power electronictechnology in the field of electric power sector has caused a greater awarenesson the power quality of distribution systems. With the re-structuring of powersystems and with shifting trend towards distributed and dispersed generation,the issue of power quality is going to take newer dimensions. The presentresearch is to identify the prominent concerns in this area and hence themeasures that can enhance the quality of power. This paper investigates theproblems of voltage sag, swell and its severe impact on nonlinear loads,sensitive loads.
Voltage Sag and Swell Identification Using FFT Analysis and Mitigation with DVRIOSRJEEE
- Power quality issues like voltage sag, swell, harmonics and transients can affect the power system performance. Voltage sag and swell are now-a-days treated to reduce power quality issues by power engineers. A small variation in voltage can badly affect the operation of power system and connected loads as well. This paper presents the voltage sag and voltage swell identification using FFT analysis. The paper also presents the mitigation for identified voltage sag and swells issues addressed with DVR. DVR consists of a voltage source converter and is controlled with d-q theory which is simple producing reference signals and gate pulses for switches of DVR. The proposed concept was simulated using MATLAB/SIMULINK software and results were presented for identification and mitigation. FFT analyses for identification of voltage sags and swell existence in different phases of power system network were shown. Mitigation of voltage sag and swell with DVR was also shown with results
CONTROL OF BATTERY OPERATED SYSTEM WITH A DC-DC BOOSTCONVERTER FED DSTATCOM U...ijiert bestjournal
This paper presents a comprehensive survey of DSTATCOM control strategies put forward recently. It is
aimed at providing a broad perspective on the status of DSTATCOM control methods to researchers and
application engineers dealing with harmonic suppression issues. Many control techniques have been
designed, developed, and realized for active filters in recent years. The proposed DSTATCOM consists of a
three-leg Voltage Source Converter (VSC) with a dc bus capacitor. The PV array or battery operated boost
converter is proposed to maintain the dc link voltage of the dc bus capacitor for continuous compensation
for the load. This paper presents to evaluate the performance comparison of two control strategies for
extracting the reference currents to control the proposed DSTATCOM. The two control methods are
Synchronous Reference Frame (SRF) theory and IcosΦ algorithm. The performance of the DSTATCOM is
validated using MATLAB software with its simulink and Power System Block set (PSB) toolboxes. The
simulation results for the two control methods are compared to validate the superior performance of the
IcosΦ algorithm.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
This paper focus on distribution system by applying different control techniques in order to improve the performance of the system. In the distribution system mainly concentrate on power quality issues like reactive power control, harmonic elimination, power factor correction, etc. Because of power quality problems voltage, current, frequency are continuously changing in power systems. These changes will effects the performance of power systems. Power quality problems can be compensated by placing DSTATCOM which is connected at PCC in parallel. It is shunt connected VSI along with the filters, with the help of DSTATCOM voltage sag, swell and THD can be controlled. This paper presents detailed explanation about performance and configuration of latest control techniques to control the DSTATCOM.
International Journal of Engineering Research and Development is an international premier peer reviewed open access engineering and technology journal promoting the discovery, innovation, advancement and dissemination of basic and transitional knowledge in engineering, technology and related disciplines.
We follow "Rigorous Publication" model - means that all articles appear on IJERD after full appraisal, effectiveness, legitimacy and reliability of research content. International Journal of Engineering Research and Development publishes papers online as well as provide hard copy of Journal to authors after publication of paper. It is intended to serve as a forum for researchers, practitioners and developers to exchange ideas and results for the advancement of Engineering & Technology.
Voltage Sag Mitigation in Utility Connected System Using Current Source Conve...IDES Editor
This paper discusses the implementation of current
source converter based distribution type static synchronous
compensator. For eliminating the lower order harmonics, the
power semiconductors are switched by pulse width modulation
technique. Current source converter, input filter, dc link
reactor are combined to design the proposed CSC based
STATCOM. Since the STATCOM is a current injection
device, the performance of the device is improved by a currentsource
converter (CSC) combination. So a controllable current
is generated at the output terminals of the device. Filter circuit
at the input terminal is designed to eliminate the higher order
harmonics. The proposed D- STATCOM is simulated and the
results are validated using MATLAB.
Simulation and Analysis of a D-STATCOM for Load Compensation and Power Facto...IJMER
Power Generation and Transmission is a complex process, requiring the working of many
components of the power system in tandem to maximize the output. One of the main components to form
a major part is the reactive power in the system. It is required to maintain the voltage to deliver the
active power through the lines. Loads like motor loads and other loads require reactive power for their
operation. To improve the performance of ac power systems, we need to manage this reactive power in
an efficient way and this is known as reactive power compensation. In developing countries like India,
where the variation of power frequency and many such other determinants of power quality are
themselves a serious question, it is very vital to take positive steps in this direction.
The work presented here illustrates a method to compensate for the load reactive power using a
DSTATCOM
A DSTATCOM injects a current into the system to provide for the reactive component of the load
current. The validity of proposed method and achievement of desired compensation are confirmed by
the results of the simulation in MATLAB/ Simulink.
1.compensation of reactive power using d statcom in grid interfaced pv systemEditorJST
This paper displays the upgrade of voltage droops, Harmonic mutilation and low power figure utilizing Distribution Static Compensator (D-STATCOM) with LCL Passive Filter in Distribution Framework. At whatever point there is an entrance of photovoltaic cell energy to the low voltage appropriated matrix, there happen the issue of confuse in voltage and recurrence in the system, maybe brought on by non-direct loads, creating music. The model depends on the Voltage Source Converter (VSC) guideline. The D-STATCOM infuses a current into the framework to alleviate the voltage lists. LCL Passive Filter Was then added to D-STATCOM to enhance symphonies bending and low power figure. The reproductions were performed utilizing MATLAB SIMULINK.
Power Quality Enhancement using DSTATCOM by Immune Feedback Control Algorithmijtsrd
This paper proposes an immune feedback control algorithm for a three phase distribution static compensator DSTATCOM to mitigate several power quality problems such as harmonics, reactive power, and load unbalancing at distribution level. This control algorithm proposed for DSTATCOM, is validated for maintaining power factor to unity, load balancing, and harmonics reduction of supply currents. In this application, the proposed control algorithm on a DSTATCOM is implemented for the compensation of nonlinear loads. The simulations were performed in the environment of MATLAB SIMULINK. P. Thirumala | K. Mahesh "Power Quality Enhancement using DSTATCOM by Immune Feedback Control Algorithm" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-4 | Issue-1 , December 2019, URL: https://www.ijtsrd.com/papers/ijtsrd29812.pdf Paper URL: https://www.ijtsrd.com/engineering/electrical-engineering/29812/power-quality-enhancement-using-dstatcom-by-immune-feedback-control-algorithm/p-thirumala
Power Quality Improvement Using Cascaded H-Bridge Multilevel Inverter Based D...IJERA Editor
Cascaded multilevel configuration of the inverter has the advantage of its simplicity and modularity over the
configurations of the diode-clamped and flying capacitor multilevel inverters. This paper presents a threephase,
five-level and seven level cascaded multilevel voltage source inverter based active filter for power line
conditioning to improve power quality in the distribution network. The DSTATCOM helps to improve the
power factor and eliminate the Total Harmonics Distortion (THD) drawn from a Non-Liner Diode Rectifier
Load (NLDRL). The compensation process is based on concept of p-q theory. A CHB Inverter is considered for
shunt compensation of a 11 kV distribution system. Finally a level shifted PWM (LSPWM) and phase shifted
PWM (PSPWM) techniques are adopted to investigate the performance of CHB Inverter. The results are
obtained through Matlab/Simulink software package.
A review on techniques and modelling methodologies used for checking electrom...nooriasukmaningtyas
The proper function of the integrated circuit (IC) in an inhibiting electromagnetic environment has always been a serious concern throughout the decades of revolution in the world of electronics, from disjunct devices to today’s integrated circuit technology, where billions of transistors are combined on a single chip. The automotive industry and smart vehicles in particular, are confronting design issues such as being prone to electromagnetic interference (EMI). Electronic control devices calculate incorrect outputs because of EMI and sensors give misleading values which can prove fatal in case of automotives. In this paper, the authors have non exhaustively tried to review research work concerned with the investigation of EMI in ICs and prediction of this EMI using various modelling methodologies and measurement setups.
Online aptitude test management system project report.pdfKamal Acharya
The purpose of on-line aptitude test system is to take online test in an efficient manner and no time wasting for checking the paper. The main objective of on-line aptitude test system is to efficiently evaluate the candidate thoroughly through a fully automated system that not only saves lot of time but also gives fast results. For students they give papers according to their convenience and time and there is no need of using extra thing like paper, pen etc. This can be used in educational institutions as well as in corporate world. Can be used anywhere any time as it is a web based application (user Location doesn’t matter). No restriction that examiner has to be present when the candidate takes the test.
Every time when lecturers/professors need to conduct examinations they have to sit down think about the questions and then create a whole new set of questions for each and every exam. In some cases the professor may want to give an open book online exam that is the student can take the exam any time anywhere, but the student might have to answer the questions in a limited time period. The professor may want to change the sequence of questions for every student. The problem that a student has is whenever a date for the exam is declared the student has to take it and there is no way he can take it at some other time. This project will create an interface for the examiner to create and store questions in a repository. It will also create an interface for the student to take examinations at his convenience and the questions and/or exams may be timed. Thereby creating an application which can be used by examiners and examinee’s simultaneously.
Examination System is very useful for Teachers/Professors. As in the teaching profession, you are responsible for writing question papers. In the conventional method, you write the question paper on paper, keep question papers separate from answers and all this information you have to keep in a locker to avoid unauthorized access. Using the Examination System you can create a question paper and everything will be written to a single exam file in encrypted format. You can set the General and Administrator password to avoid unauthorized access to your question paper. Every time you start the examination, the program shuffles all the questions and selects them randomly from the database, which reduces the chances of memorizing the questions.
HEAP SORT ILLUSTRATED WITH HEAPIFY, BUILD HEAP FOR DYNAMIC ARRAYS.
Heap sort is a comparison-based sorting technique based on Binary Heap data structure. It is similar to the selection sort where we first find the minimum element and place the minimum element at the beginning. Repeat the same process for the remaining elements.
NUMERICAL SIMULATIONS OF HEAT AND MASS TRANSFER IN CONDENSING HEAT EXCHANGERS...ssuser7dcef0
Power plants release a large amount of water vapor into the
atmosphere through the stack. The flue gas can be a potential
source for obtaining much needed cooling water for a power
plant. If a power plant could recover and reuse a portion of this
moisture, it could reduce its total cooling water intake
requirement. One of the most practical way to recover water
from flue gas is to use a condensing heat exchanger. The power
plant could also recover latent heat due to condensation as well
as sensible heat due to lowering the flue gas exit temperature.
Additionally, harmful acids released from the stack can be
reduced in a condensing heat exchanger by acid condensation. reduced in a condensing heat exchanger by acid condensation.
Condensation of vapors in flue gas is a complicated
phenomenon since heat and mass transfer of water vapor and
various acids simultaneously occur in the presence of noncondensable
gases such as nitrogen and oxygen. Design of a
condenser depends on the knowledge and understanding of the
heat and mass transfer processes. A computer program for
numerical simulations of water (H2O) and sulfuric acid (H2SO4)
condensation in a flue gas condensing heat exchanger was
developed using MATLAB. Governing equations based on
mass and energy balances for the system were derived to
predict variables such as flue gas exit temperature, cooling
water outlet temperature, mole fraction and condensation rates
of water and sulfuric acid vapors. The equations were solved
using an iterative solution technique with calculations of heat
and mass transfer coefficients and physical properties.
TOP 10 B TECH COLLEGES IN JAIPUR 2024.pptxnikitacareer3
Looking for the best engineering colleges in Jaipur for 2024?
Check out our list of the top 10 B.Tech colleges to help you make the right choice for your future career!
1) MNIT
2) MANIPAL UNIV
3) LNMIIT
4) NIMS UNIV
5) JECRC
6) VIVEKANANDA GLOBAL UNIV
7) BIT JAIPUR
8) APEX UNIV
9) AMITY UNIV.
10) JNU
TO KNOW MORE ABOUT COLLEGES, FEES AND PLACEMENT, WATCH THE FULL VIDEO GIVEN BELOW ON "TOP 10 B TECH COLLEGES IN JAIPUR"
https://www.youtube.com/watch?v=vSNje0MBh7g
VISIT CAREER MANTRA PORTAL TO KNOW MORE ABOUT COLLEGES/UNIVERSITITES in Jaipur:
https://careermantra.net/colleges/3378/Jaipur/b-tech
Get all the information you need to plan your next steps in your medical career with Career Mantra!
https://careermantra.net/
6th International Conference on Machine Learning & Applications (CMLA 2024)ClaraZara1
6th International Conference on Machine Learning & Applications (CMLA 2024) will provide an excellent international forum for sharing knowledge and results in theory, methodology and applications of on Machine Learning & Applications.