This study investigates experimentally the performance of two-dimensional solar tracking systems with reflector using commercial silicon based photovoltaic module, with open and closed loop control systems. Different reflector materials were also investigated. The experiments were performed at the Hashemite University campus in Zarqa at a latitude of 32⁰, in February and March. Photovoltaic output power and performance were analyzed. It was found that the modified photovoltaic module with mirror reflector generated the highest value of power, while the temperature reached a maximum value of 53 ̊ C. The modified module suggested in this study produced 5% more PV power than the two-dimensional solar tracking systems without reflector and produced 12.5% more PV power than the fixed PV module with 26⁰ tilt angle.
This study investigates experimentally the performance of two-dimensional solar tracking systems with reflector using commercial silicon based photovoltaic module, with open and closed loop control systems. Different reflector materials were also investigated. The experiments were performed at the Hashemite University campus in Zarqa at a latitude of 32⁰, in February and March. Photovoltaic output power and performance were analyzed. It was found that the modified photovoltaic module with mirror reflector generated the highest value of power, while the temperature reached a maximum value of 53 ̊ C. The modified module suggested in this study produced 5% more PV power than the two-dimensional solar tracking systems without reflector and produced 12.5% more PV power than the fixed PV module with 26⁰ tilt angle.
Experimental Analysis of Factors Affecting the Power Output of the PV Module IJECEIAES
Energy is the driving force in all the sectors as it acts like an index of standard of living or prosperity of the people of the country. However heavy dependence on fossil fuels leads to global warming, hence there is a need for the use of clean, sustainable, and eco friendly form of energy. Among the various types of non-conventional energy solar energy is the fundamental as it is abundant, pollution free and universally available.Even though the main input to the PV system is the solar radiation still there are other factors which affects the efficiency of the pv module. In this paper real time experiment has been conducted to analyze the effect of various factors like irradiance, temperature, and angle of tilt, soiling, shading on the power output of the pv module. Temperature is a negative factor which reduces the efficiency of the module and can be reduced by various cooling arrangements. Presence of dust particles and shading obstructs the incident solar radiations entering the panel and the effect is seen in the iv and pv curve .For better performance solar tracking at maximum power point is suggested to improve the power output of the pv module.
Solar Plate Indexing To Improve Efficiency of Present Solar Power Systempaperpublications3
Abstract: Although solar plate are being used from very long ago in the world for generation of power in non-conventional form, but still there is hording of improving efficiency of the currently available stationery solar plates. Solar plate indexing system is also one of such efforts made to improve efficiency of solar power extraction. Survey data say that very few days are left when the all reserves will nearly deplete i.e. till 2050 all the reserves of petroleum products which are available under earth will vanish. Therefore, human being is very much worried about the future energy sources. Aiming the improvement of the efficiency of current energy generating equipment’s we have designed to index the solar plate according to the solar track so that perpendicular rays could fall on the plates. We have used 5 watt, 1550 rpm motor to rotate the shaft on which our solar plate is mounted. Electronic cyclic timers have been used to index the plate in the span of 1200 in the duration if 8 hours a day. On-off switch have been used to start the cycle of rotation of plate. Sunrise and sunset limiting switches have been used to decide the pan of the solar plate. After testing the indexed plate solar system on the real ground we have found the result that current stationery plate after charging for 8 hours in the full sunny-day can give uses of 4 hour whereas our indexed plate on charging for the same duration can deliver 6 hour of service. This result is really encouraging and improving the efficiency of current solar plates
A NOVEL APPROACH TO OBTAIN MAXIMUM POWER OUTPUT FROM SOLAR PANEL USING PSOijsrd.com
The configuration of a most extreme force point following (MPPT) controller for a sun based photovoltaic force framework is proposed using a help converter topology utilizing PSO calculation. Sunlight based board voltage and current are consistently checked by a shut circle focused around PSO microcontroller control framework, and the obligation cycle of the help converter persistently changed in accordance with concentrate greatest force. Framework testing affirms crest force following under changing lighting conditions. Under particular conditions, efficiencies in overabundance of 96% are demonstrated to be conceivable.
Experimental Analysis of Factors Affecting the Power Output of the PV Module IJECEIAES
Energy is the driving force in all the sectors as it acts like an index of standard of living or prosperity of the people of the country. However heavy dependence on fossil fuels leads to global warming, hence there is a need for the use of clean, sustainable, and eco friendly form of energy. Among the various types of non-conventional energy solar energy is the fundamental as it is abundant, pollution free and universally available.Even though the main input to the PV system is the solar radiation still there are other factors which affects the efficiency of the pv module. In this paper real time experiment has been conducted to analyze the effect of various factors like irradiance, temperature, and angle of tilt, soiling, shading on the power output of the pv module. Temperature is a negative factor which reduces the efficiency of the module and can be reduced by various cooling arrangements. Presence of dust particles and shading obstructs the incident solar radiations entering the panel and the effect is seen in the iv and pv curve .For better performance solar tracking at maximum power point is suggested to improve the power output of the pv module.
Solar Plate Indexing To Improve Efficiency of Present Solar Power Systempaperpublications3
Abstract: Although solar plate are being used from very long ago in the world for generation of power in non-conventional form, but still there is hording of improving efficiency of the currently available stationery solar plates. Solar plate indexing system is also one of such efforts made to improve efficiency of solar power extraction. Survey data say that very few days are left when the all reserves will nearly deplete i.e. till 2050 all the reserves of petroleum products which are available under earth will vanish. Therefore, human being is very much worried about the future energy sources. Aiming the improvement of the efficiency of current energy generating equipment’s we have designed to index the solar plate according to the solar track so that perpendicular rays could fall on the plates. We have used 5 watt, 1550 rpm motor to rotate the shaft on which our solar plate is mounted. Electronic cyclic timers have been used to index the plate in the span of 1200 in the duration if 8 hours a day. On-off switch have been used to start the cycle of rotation of plate. Sunrise and sunset limiting switches have been used to decide the pan of the solar plate. After testing the indexed plate solar system on the real ground we have found the result that current stationery plate after charging for 8 hours in the full sunny-day can give uses of 4 hour whereas our indexed plate on charging for the same duration can deliver 6 hour of service. This result is really encouraging and improving the efficiency of current solar plates
A NOVEL APPROACH TO OBTAIN MAXIMUM POWER OUTPUT FROM SOLAR PANEL USING PSOijsrd.com
The configuration of a most extreme force point following (MPPT) controller for a sun based photovoltaic force framework is proposed using a help converter topology utilizing PSO calculation. Sunlight based board voltage and current are consistently checked by a shut circle focused around PSO microcontroller control framework, and the obligation cycle of the help converter persistently changed in accordance with concentrate greatest force. Framework testing affirms crest force following under changing lighting conditions. Under particular conditions, efficiencies in overabundance of 96% are demonstrated to be conceivable.
A review on techniques and modelling methodologies used for checking electrom...nooriasukmaningtyas
The proper function of the integrated circuit (IC) in an inhibiting electromagnetic environment has always been a serious concern throughout the decades of revolution in the world of electronics, from disjunct devices to today’s integrated circuit technology, where billions of transistors are combined on a single chip. The automotive industry and smart vehicles in particular, are confronting design issues such as being prone to electromagnetic interference (EMI). Electronic control devices calculate incorrect outputs because of EMI and sensors give misleading values which can prove fatal in case of automotives. In this paper, the authors have non exhaustively tried to review research work concerned with the investigation of EMI in ICs and prediction of this EMI using various modelling methodologies and measurement setups.
6th International Conference on Machine Learning & Applications (CMLA 2024)ClaraZara1
6th International Conference on Machine Learning & Applications (CMLA 2024) will provide an excellent international forum for sharing knowledge and results in theory, methodology and applications of on Machine Learning & Applications.
Using recycled concrete aggregates (RCA) for pavements is crucial to achieving sustainability. Implementing RCA for new pavement can minimize carbon footprint, conserve natural resources, reduce harmful emissions, and lower life cycle costs. Compared to natural aggregate (NA), RCA pavement has fewer comprehensive studies and sustainability assessments.
Understanding Inductive Bias in Machine LearningSUTEJAS
This presentation explores the concept of inductive bias in machine learning. It explains how algorithms come with built-in assumptions and preferences that guide the learning process. You'll learn about the different types of inductive bias and how they can impact the performance and generalizability of machine learning models.
The presentation also covers the positive and negative aspects of inductive bias, along with strategies for mitigating potential drawbacks. We'll explore examples of how bias manifests in algorithms like neural networks and decision trees.
By understanding inductive bias, you can gain valuable insights into how machine learning models work and make informed decisions when building and deploying them.
TOP 10 B TECH COLLEGES IN JAIPUR 2024.pptxnikitacareer3
Looking for the best engineering colleges in Jaipur for 2024?
Check out our list of the top 10 B.Tech colleges to help you make the right choice for your future career!
1) MNIT
2) MANIPAL UNIV
3) LNMIIT
4) NIMS UNIV
5) JECRC
6) VIVEKANANDA GLOBAL UNIV
7) BIT JAIPUR
8) APEX UNIV
9) AMITY UNIV.
10) JNU
TO KNOW MORE ABOUT COLLEGES, FEES AND PLACEMENT, WATCH THE FULL VIDEO GIVEN BELOW ON "TOP 10 B TECH COLLEGES IN JAIPUR"
https://www.youtube.com/watch?v=vSNje0MBh7g
VISIT CAREER MANTRA PORTAL TO KNOW MORE ABOUT COLLEGES/UNIVERSITITES in Jaipur:
https://careermantra.net/colleges/3378/Jaipur/b-tech
Get all the information you need to plan your next steps in your medical career with Career Mantra!
https://careermantra.net/
NUMERICAL SIMULATIONS OF HEAT AND MASS TRANSFER IN CONDENSING HEAT EXCHANGERS...ssuser7dcef0
Power plants release a large amount of water vapor into the
atmosphere through the stack. The flue gas can be a potential
source for obtaining much needed cooling water for a power
plant. If a power plant could recover and reuse a portion of this
moisture, it could reduce its total cooling water intake
requirement. One of the most practical way to recover water
from flue gas is to use a condensing heat exchanger. The power
plant could also recover latent heat due to condensation as well
as sensible heat due to lowering the flue gas exit temperature.
Additionally, harmful acids released from the stack can be
reduced in a condensing heat exchanger by acid condensation. reduced in a condensing heat exchanger by acid condensation.
Condensation of vapors in flue gas is a complicated
phenomenon since heat and mass transfer of water vapor and
various acids simultaneously occur in the presence of noncondensable
gases such as nitrogen and oxygen. Design of a
condenser depends on the knowledge and understanding of the
heat and mass transfer processes. A computer program for
numerical simulations of water (H2O) and sulfuric acid (H2SO4)
condensation in a flue gas condensing heat exchanger was
developed using MATLAB. Governing equations based on
mass and energy balances for the system were derived to
predict variables such as flue gas exit temperature, cooling
water outlet temperature, mole fraction and condensation rates
of water and sulfuric acid vapors. The equations were solved
using an iterative solution technique with calculations of heat
and mass transfer coefficients and physical properties.