This document summarizes a study that examined the effects of adding granite powder and polypropylene fibers on the compressive, split tensile, and flexural strengths of concrete. Granite powder was used to replace river sand in proportions of 10%, 20%, and 30%. Polypropylene fibers made up 0.25% of the cement weight. Specimens were tested for strengths at 7, 28, and 56 days and after exposure to 300°C. Results showed that concrete with 20% granite powder replacement had improved compressive strength compared to normal concrete. The study aimed to develop more durable and heat-resistant concrete using industrial waste materials.
A Study on Partial Replacement of Natural Granite Aggregate with Pelletized F...ijceronline
International Journal of Computational Engineering Research (IJCER) is dedicated to protecting personal information and will make every reasonable effort to handle collected information appropriately. All information collected, as well as related requests, will be handled as carefully and efficiently as possible in accordance with IJCER standards for integrity and objectivity.
A Study on Partial Replacement of Natural Granite Aggregate with Pelletized F...ijceronline
International Journal of Computational Engineering Research (IJCER) is dedicated to protecting personal information and will make every reasonable effort to handle collected information appropriately. All information collected, as well as related requests, will be handled as carefully and efficiently as possible in accordance with IJCER standards for integrity and objectivity.
Comparatives study of M20 grade conventional concrete pavement with M20 grade...IJSRD
This project work involves an experimental and laboratory study of the Polypropylene fibers with two types of admixtures those are Quarry dust and Fly ash on the mechanical properties of the concrete used in the rigid pavement. In this experimental study involves two types of concrete mixes were prepared individually. Polypropylene fiber of 1% to 3% with Quarry dust of 0.1% to 0.3% and Polypropylene fiber of 1% to 4% with Fly ash of 0.1% to 0.4% by weight of cement were added to the mixes. After that a comparative analysis has been carried out for conventional concrete to that of the fiber reinforced in relation to their compressive, split tensile and flexural properties. By the experimental work the compressive, split tensile and flexural strengths are proportionally increased both Polypropylene + Quarry dust and Polypropylene +Fly ash usage. It is observed that the optimum dosages of Polypropylene + Quarry dust is 3% + 0.3% Polypropylene +Fly ash is 4%+ 0.4% by weight of cement. In this project cost analysis is also determined for conventional concrete and fiber reinforced with admixtures individually using experimental test reports. By analyzing the cost it was found that Polypropylene reinforced concrete with quarry dust pavement is economical than Polypropylene reinforced concrete with Fly ash pavement.
AN EXPERIMENTAL STUDY ON PROPERTIES OF TERNARY BLENDED CONCRETE USING GGBS AN...AM Publications
Ground granulated blast furnace slag (GGBS) is a by-product obtained from the blast furnaces used in the iron manufacturing industry. The disposal of the marble powder obtained from marble industry constitutes one of the environmental problems around the world. One of the possible solutions for the effective use of GGBS and marble powder is to partially replace cement in concrete. This paper presents the results of an experimental study on concrete in which the cement is partially replaced by both GGBS and marble powder. In this study, different percentages of GGBS and marble powder are used for partial replacement of cement by 30%. Tests conducted includes workability of fresh concrete (Slump test), strength of hardened concrete (Compressive strength, Split tensile strength and Flexural strength) and durability properties of concrete (Chloride resistance and Sulphate resistance).
Impact test on geopolymer concrete slabseSAT Journals
Abstract
Geopolymer is an eco-friendly binding material alternative for Ordinary Portland Cement (OPC). Geopolymer concrete is
produced by mixing fly ash, GGBS, alkaline solution, fine aggregate and coarse aggregate. Alkaline solution is composed of
NaOH and Na2SiO3 solution. This paper deals with the study of impact resistance capacity of geopolymer concrete slabs
subjected to impact loading. For this study, ten specimens of size 600 mm (length) × 600 mm (width) × 60 mm (thick) were casted
with nine different combination of geopolymer concrete mix using different molar sodium hydroxide solutions and different
percentages of mineral admixtures and a normal concrete slab as control slab. The molarity of NaOH solution used was 8M, 12M
and 16M. Fly ash and GGBS admixtures were used in three different ratios of 100:0, 75:25 and 50:50.The slabs were oven cured
at 600C for 24 hours. These slabs were subjected to impact loading by drop weight test method. All the slabs were tested under a
drop weight of 75.50 N through a guide pipe from a height of 700mm. The results obtained from this study showed that with the
increase in molarity of NaOH solution, the strength characteristics and the impact resistance capacity of the specimen increases.
Also increase in percentage of GGBS content as replacement for Fly ash content increases the impact resistance and overall
strength characteristics of geopolymer concrete. From the test results, geopolymer concrete slab with 16M NaOH solution using
50:50 Fly ash and GGBS content showed higher impact energy absorption capacity as compared other geopolymer mixes.
Key Words: Geopolymer, Molarity, Impact loading, First crack, Ultimate failure etc…
IJERA (International journal of Engineering Research and Applications) is International online, ... peer reviewed journal. For more detail or submit your article, please visit www.ijera.com
Disposal of tyre rubber is becoming a huge problem in India day by day.
Researchers are trying to use those rubber in civil engineering projects from long day
back. Crumb rubber replaced fine aggregate is qute a common practice now a days.
An attempt was made to replace 10% chipped rubber with coarse aggregate and
beams were casted with that concrete mix.They were tested to failure. Deflection,
ultimate load, first crack,stress vs strain,load vs deflection are all studied. Efforts
have been taken to identify the potential application of waste tyres in civil engineering
projects. This study can show an alternative way of recycling tyre by incorporating
them into concrete construction. Main focus was made on the behaviour of beam
made from recycled rubber chips .
Improved Concrete Properties Using Quarry Dust as Replacement for Natural SandIJERD Editor
Concrete plays a major role in the construction industry. Natural sand is a prime material used for
the preparation of concrete and also plays an important role in Mix Design. Now a day’s river erosion and other
environmental issues have led to the scarcity of river sand. The reduction in the sources of natural sand and the
requirement for reduction in the cost of concrete production has resulted in the increased need to find new
alternative materials to replace river sand so that excess river erosion is prevented and high strength concrete is
obtained at lower cost. One such material is Quarry stone dust: a by-product obtained during quarrying process.
Attempts have been made to study the suitability of Quarry dust as sand replacing material and it has been found
that Quarry dust improves the mechanical properties of concrete as well as elastic modulus. The optimum
compressive strength is achieved at the proportion of fine to coarse with 60:40 ratio
Experimental Investigation on Replacement of Cement in Concrete Partially by ...ijtsrd
Concrete is the most extremely used construction material within the world, which always uses natural resources like lime, aggregates and water. The production of cement in world has increased greatly, due to this cement production emission of CO2 gas has been increased tremendously, ultimately environmental pollution increased to very large extent. This affect to environment has been reduced by cement has been replaced by some supplementary materials like Dolamite Powder or Fly ash or GGBS and so on. Dolamite. Powder was conducted detailed study and lots of research work has been made on other waste materials and it is found there is a great future scope for research on Dolamite Powder as a replacement to cement, sand or both. Now in our case, cement has been replaced partially with in varying proportions likewise from 0 to 20 and its effect has been analysed on the standard consistency, soundness, setting times of cement and compressive strength of cement mortar mixes. The cubes and cylinders of concrete were casted for variable content of dolomite powder. Pramod Dhamne | Dr. P. B. Nagarnaik ""Experimental Investigation on Replacement of Cement in Concrete Partially by using Dolamite Powder"" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-3 , April 2019, URL: https://www.ijtsrd.com/papers/ijtsrd23035.pdf
Paper URL: https://www.ijtsrd.com/engineering/civil-engineering/23035/experimental-investigation-on-replacement-of-cement-in-concrete-partially-by-using-dolamite-powder/pramod-dhamne
The Journal of MC Square Scientific Research is published by MC Square Publication on the monthly basis. It aims to publish original research papers devoted to wide areas in various disciplines of science and engineering and their applications in industry. This journal is basically devoted to interdisciplinary research in Science, Engineering and Technology, which can improve the technology being used in industry. The real-life problems involve multi-disciplinary knowledge, and thus strong inter-disciplinary approach is the need of the research.
Self-compacting concrete is high performance concrete which is highly flowable, non-segregating, spread on its
own weight and doesn‟t need any compaction. This paper deals with flow and strength characteristics such as
compressive strength, split tensile strength, flexural strength and impact strength of Self-compacting concrete
with various percentages of waste plastic fibres like 0%, 0.25%, 0.5%, 0.75%, 1.0%, 1.1%, 1.20%, 1.3% and
1.4% is added by weight of cement. The mix proportion for M40 grade of concrete was done by using Nan Su
method (Cement: GGBS: Fine aggregate: Course aggregate 1: 0.705: 3.34: 2.62). Water powder (W/P) ratio
0.36, cement content 280kg/m3
, GGBS 220 kg/m3 was calculated and maintained as constant throughout the
experimental work for all eight mixes, only the superplastizers dosage was varied for different percentage of
fibres. In this experimental investigation one control mix and eight (8) different mixes were considered. Totally
81 Cube, beam, Cylindrical specimens and square plates were casted, cured and tested as per IS specifications.
For determining impact strength drop weight method was used. The results obtained indicate that fresh
(workability) characteristics satisfy the lower and upper limit as suggested by EFNARC. The tests on hardened
properties indicate that the compressive strength, split tensile strength, flexural strength was improved
proportionally with the addition of waste plastic fibers upto 1.0% by weight of cement and then decreases. The
impact strength improved proportionally with addition of fibres upto 1.2% by weight of cement and then
decreases
Recycled aggregates consist of crushed, graded inorganic particles processed from the material that have been used in the constructions and demolition debris. The target of the present thesis work is to determine the strength characteristic of recycled aggregates for the application in concrete pavement construction. The scope of the thesis is to determine and compare the compressive strength, flexural strength and sulphate resistance of concrete by using different percentages of recycled aggregates. The investigation was carried out by using workability test, compressive strength test, flexural strength test and sulphate resistance test. A total of five mixes with replacement of coarse aggregates with 0%, 10%, 20%, 30% and 40% recycled coarse aggregates were studied. The water cement ratio was kept constant at 0.38. It was observed that workability of concrete was decreased with the increase in recycled aggregates in concrete. For the strength characteristics, the results showed that the strengths of recycled aggregate concrete was comparable to the strengths of natural aggregates concrete. Munesh Kumar | Sumesh Jain"Use of Demorlished Concrete in Pavement" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-1 | Issue-5 , August 2017, URL: http://www.ijtsrd.com/papers/ijtsrd2369.pdf http://www.ijtsrd.com/engineering/civil-engineering/2369/use-of-demorlished-concrete-in-pavement/munesh-kumar
International Journal of Computational Engineering Research(IJCER) is an intentional online Journal in English monthly publishing journal. This Journal publish original research work that contributes significantly to further the scientific knowledge in engineering and Technology
Comparatives study of M20 grade conventional concrete pavement with M20 grade...IJSRD
This project work involves an experimental and laboratory study of the Polypropylene fibers with two types of admixtures those are Quarry dust and Fly ash on the mechanical properties of the concrete used in the rigid pavement. In this experimental study involves two types of concrete mixes were prepared individually. Polypropylene fiber of 1% to 3% with Quarry dust of 0.1% to 0.3% and Polypropylene fiber of 1% to 4% with Fly ash of 0.1% to 0.4% by weight of cement were added to the mixes. After that a comparative analysis has been carried out for conventional concrete to that of the fiber reinforced in relation to their compressive, split tensile and flexural properties. By the experimental work the compressive, split tensile and flexural strengths are proportionally increased both Polypropylene + Quarry dust and Polypropylene +Fly ash usage. It is observed that the optimum dosages of Polypropylene + Quarry dust is 3% + 0.3% Polypropylene +Fly ash is 4%+ 0.4% by weight of cement. In this project cost analysis is also determined for conventional concrete and fiber reinforced with admixtures individually using experimental test reports. By analyzing the cost it was found that Polypropylene reinforced concrete with quarry dust pavement is economical than Polypropylene reinforced concrete with Fly ash pavement.
AN EXPERIMENTAL STUDY ON PROPERTIES OF TERNARY BLENDED CONCRETE USING GGBS AN...AM Publications
Ground granulated blast furnace slag (GGBS) is a by-product obtained from the blast furnaces used in the iron manufacturing industry. The disposal of the marble powder obtained from marble industry constitutes one of the environmental problems around the world. One of the possible solutions for the effective use of GGBS and marble powder is to partially replace cement in concrete. This paper presents the results of an experimental study on concrete in which the cement is partially replaced by both GGBS and marble powder. In this study, different percentages of GGBS and marble powder are used for partial replacement of cement by 30%. Tests conducted includes workability of fresh concrete (Slump test), strength of hardened concrete (Compressive strength, Split tensile strength and Flexural strength) and durability properties of concrete (Chloride resistance and Sulphate resistance).
Impact test on geopolymer concrete slabseSAT Journals
Abstract
Geopolymer is an eco-friendly binding material alternative for Ordinary Portland Cement (OPC). Geopolymer concrete is
produced by mixing fly ash, GGBS, alkaline solution, fine aggregate and coarse aggregate. Alkaline solution is composed of
NaOH and Na2SiO3 solution. This paper deals with the study of impact resistance capacity of geopolymer concrete slabs
subjected to impact loading. For this study, ten specimens of size 600 mm (length) × 600 mm (width) × 60 mm (thick) were casted
with nine different combination of geopolymer concrete mix using different molar sodium hydroxide solutions and different
percentages of mineral admixtures and a normal concrete slab as control slab. The molarity of NaOH solution used was 8M, 12M
and 16M. Fly ash and GGBS admixtures were used in three different ratios of 100:0, 75:25 and 50:50.The slabs were oven cured
at 600C for 24 hours. These slabs were subjected to impact loading by drop weight test method. All the slabs were tested under a
drop weight of 75.50 N through a guide pipe from a height of 700mm. The results obtained from this study showed that with the
increase in molarity of NaOH solution, the strength characteristics and the impact resistance capacity of the specimen increases.
Also increase in percentage of GGBS content as replacement for Fly ash content increases the impact resistance and overall
strength characteristics of geopolymer concrete. From the test results, geopolymer concrete slab with 16M NaOH solution using
50:50 Fly ash and GGBS content showed higher impact energy absorption capacity as compared other geopolymer mixes.
Key Words: Geopolymer, Molarity, Impact loading, First crack, Ultimate failure etc…
IJERA (International journal of Engineering Research and Applications) is International online, ... peer reviewed journal. For more detail or submit your article, please visit www.ijera.com
Disposal of tyre rubber is becoming a huge problem in India day by day.
Researchers are trying to use those rubber in civil engineering projects from long day
back. Crumb rubber replaced fine aggregate is qute a common practice now a days.
An attempt was made to replace 10% chipped rubber with coarse aggregate and
beams were casted with that concrete mix.They were tested to failure. Deflection,
ultimate load, first crack,stress vs strain,load vs deflection are all studied. Efforts
have been taken to identify the potential application of waste tyres in civil engineering
projects. This study can show an alternative way of recycling tyre by incorporating
them into concrete construction. Main focus was made on the behaviour of beam
made from recycled rubber chips .
Improved Concrete Properties Using Quarry Dust as Replacement for Natural SandIJERD Editor
Concrete plays a major role in the construction industry. Natural sand is a prime material used for
the preparation of concrete and also plays an important role in Mix Design. Now a day’s river erosion and other
environmental issues have led to the scarcity of river sand. The reduction in the sources of natural sand and the
requirement for reduction in the cost of concrete production has resulted in the increased need to find new
alternative materials to replace river sand so that excess river erosion is prevented and high strength concrete is
obtained at lower cost. One such material is Quarry stone dust: a by-product obtained during quarrying process.
Attempts have been made to study the suitability of Quarry dust as sand replacing material and it has been found
that Quarry dust improves the mechanical properties of concrete as well as elastic modulus. The optimum
compressive strength is achieved at the proportion of fine to coarse with 60:40 ratio
Experimental Investigation on Replacement of Cement in Concrete Partially by ...ijtsrd
Concrete is the most extremely used construction material within the world, which always uses natural resources like lime, aggregates and water. The production of cement in world has increased greatly, due to this cement production emission of CO2 gas has been increased tremendously, ultimately environmental pollution increased to very large extent. This affect to environment has been reduced by cement has been replaced by some supplementary materials like Dolamite Powder or Fly ash or GGBS and so on. Dolamite. Powder was conducted detailed study and lots of research work has been made on other waste materials and it is found there is a great future scope for research on Dolamite Powder as a replacement to cement, sand or both. Now in our case, cement has been replaced partially with in varying proportions likewise from 0 to 20 and its effect has been analysed on the standard consistency, soundness, setting times of cement and compressive strength of cement mortar mixes. The cubes and cylinders of concrete were casted for variable content of dolomite powder. Pramod Dhamne | Dr. P. B. Nagarnaik ""Experimental Investigation on Replacement of Cement in Concrete Partially by using Dolamite Powder"" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-3 , April 2019, URL: https://www.ijtsrd.com/papers/ijtsrd23035.pdf
Paper URL: https://www.ijtsrd.com/engineering/civil-engineering/23035/experimental-investigation-on-replacement-of-cement-in-concrete-partially-by-using-dolamite-powder/pramod-dhamne
The Journal of MC Square Scientific Research is published by MC Square Publication on the monthly basis. It aims to publish original research papers devoted to wide areas in various disciplines of science and engineering and their applications in industry. This journal is basically devoted to interdisciplinary research in Science, Engineering and Technology, which can improve the technology being used in industry. The real-life problems involve multi-disciplinary knowledge, and thus strong inter-disciplinary approach is the need of the research.
Self-compacting concrete is high performance concrete which is highly flowable, non-segregating, spread on its
own weight and doesn‟t need any compaction. This paper deals with flow and strength characteristics such as
compressive strength, split tensile strength, flexural strength and impact strength of Self-compacting concrete
with various percentages of waste plastic fibres like 0%, 0.25%, 0.5%, 0.75%, 1.0%, 1.1%, 1.20%, 1.3% and
1.4% is added by weight of cement. The mix proportion for M40 grade of concrete was done by using Nan Su
method (Cement: GGBS: Fine aggregate: Course aggregate 1: 0.705: 3.34: 2.62). Water powder (W/P) ratio
0.36, cement content 280kg/m3
, GGBS 220 kg/m3 was calculated and maintained as constant throughout the
experimental work for all eight mixes, only the superplastizers dosage was varied for different percentage of
fibres. In this experimental investigation one control mix and eight (8) different mixes were considered. Totally
81 Cube, beam, Cylindrical specimens and square plates were casted, cured and tested as per IS specifications.
For determining impact strength drop weight method was used. The results obtained indicate that fresh
(workability) characteristics satisfy the lower and upper limit as suggested by EFNARC. The tests on hardened
properties indicate that the compressive strength, split tensile strength, flexural strength was improved
proportionally with the addition of waste plastic fibers upto 1.0% by weight of cement and then decreases. The
impact strength improved proportionally with addition of fibres upto 1.2% by weight of cement and then
decreases
Recycled aggregates consist of crushed, graded inorganic particles processed from the material that have been used in the constructions and demolition debris. The target of the present thesis work is to determine the strength characteristic of recycled aggregates for the application in concrete pavement construction. The scope of the thesis is to determine and compare the compressive strength, flexural strength and sulphate resistance of concrete by using different percentages of recycled aggregates. The investigation was carried out by using workability test, compressive strength test, flexural strength test and sulphate resistance test. A total of five mixes with replacement of coarse aggregates with 0%, 10%, 20%, 30% and 40% recycled coarse aggregates were studied. The water cement ratio was kept constant at 0.38. It was observed that workability of concrete was decreased with the increase in recycled aggregates in concrete. For the strength characteristics, the results showed that the strengths of recycled aggregate concrete was comparable to the strengths of natural aggregates concrete. Munesh Kumar | Sumesh Jain"Use of Demorlished Concrete in Pavement" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-1 | Issue-5 , August 2017, URL: http://www.ijtsrd.com/papers/ijtsrd2369.pdf http://www.ijtsrd.com/engineering/civil-engineering/2369/use-of-demorlished-concrete-in-pavement/munesh-kumar
International Journal of Computational Engineering Research(IJCER) is an intentional online Journal in English monthly publishing journal. This Journal publish original research work that contributes significantly to further the scientific knowledge in engineering and Technology
Experimental Study of Partial Replacement of Cement in Concrete with Marble D...YogeshIJTSRD
The advancement of concrete technology is abridging the usance of natural and energy asset, and lessen the pollution of environment by the industrial waste. Marble is a metamorphic rock, resulting from the transformation of pure lime stone. Marble dust is generated in stone processing plants which pollute the environment and affect the humans directly or indirectly. Marble is industrially processed by being cut, polished and used for decorative purpose and thus, economically variable. During cutting process, 20 30 of a marble block becomes waste marble powder. Krishnendra Kumar Shukla | Hirendra Pratap Singh "Experimental Study of Partial Replacement of Cement in Concrete with Marble Dust and Recron Fibre as Admixture" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-5 | Issue-3 , April 2021, URL: https://www.ijtsrd.com/papers/ijtsrd38703.pdf Paper URL: https://www.ijtsrd.com/engineering/civil-engineering/38703/experimental-study-of-partial-replacement-of-cement-in-concrete-with-marble-dust-and-recron-fibre-as-admixture/krishnendra-kumar-shukla
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
COLLEGE BUS MANAGEMENT SYSTEM PROJECT REPORT.pdfKamal Acharya
The College Bus Management system is completely developed by Visual Basic .NET Version. The application is connect with most secured database language MS SQL Server. The application is develop by using best combination of front-end and back-end languages. The application is totally design like flat user interface. This flat user interface is more attractive user interface in 2017. The application is gives more important to the system functionality. The application is to manage the student’s details, driver’s details, bus details, bus route details, bus fees details and more. The application has only one unit for admin. The admin can manage the entire application. The admin can login into the application by using username and password of the admin. The application is develop for big and small colleges. It is more user friendly for non-computer person. Even they can easily learn how to manage the application within hours. The application is more secure by the admin. The system will give an effective output for the VB.Net and SQL Server given as input to the system. The compiled java program given as input to the system, after scanning the program will generate different reports. The application generates the report for users. The admin can view and download the report of the data. The application deliver the excel format reports. Because, excel formatted reports is very easy to understand the income and expense of the college bus. This application is mainly develop for windows operating system users. In 2017, 73% of people enterprises are using windows operating system. So the application will easily install for all the windows operating system users. The application-developed size is very low. The application consumes very low space in disk. Therefore, the user can allocate very minimum local disk space for this application.
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
Democratizing Fuzzing at Scale by Abhishek Aryaabh.arya
Presented at NUS: Fuzzing and Software Security Summer School 2024
This keynote talks about the democratization of fuzzing at scale, highlighting the collaboration between open source communities, academia, and industry to advance the field of fuzzing. It delves into the history of fuzzing, the development of scalable fuzzing platforms, and the empowerment of community-driven research. The talk will further discuss recent advancements leveraging AI/ML and offer insights into the future evolution of the fuzzing landscape.
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...Amil Baba Dawood bangali
Contact with Dawood Bhai Just call on +92322-6382012 and we'll help you. We'll solve all your problems within 12 to 24 hours and with 101% guarantee and with astrology systematic. If you want to take any personal or professional advice then also you can call us on +92322-6382012 , ONLINE LOVE PROBLEM & Other all types of Daily Life Problem's.Then CALL or WHATSAPP us on +92322-6382012 and Get all these problems solutions here by Amil Baba DAWOOD BANGALI
#vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore#blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #blackmagicforlove #blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #Amilbabainuk #amilbabainspain #amilbabaindubai #Amilbabainnorway #amilbabainkrachi #amilbabainlahore #amilbabaingujranwalan #amilbabainislamabad
Vaccine management system project report documentation..pdfKamal Acharya
The Division of Vaccine and Immunization is facing increasing difficulty monitoring vaccines and other commodities distribution once they have been distributed from the national stores. With the introduction of new vaccines, more challenges have been anticipated with this additions posing serious threat to the already over strained vaccine supply chain system in Kenya.
Quality defects in TMT Bars, Possible causes and Potential Solutions.PrashantGoswami42
Maintaining high-quality standards in the production of TMT bars is crucial for ensuring structural integrity in construction. Addressing common defects through careful monitoring, standardized processes, and advanced technology can significantly improve the quality of TMT bars. Continuous training and adherence to quality control measures will also play a pivotal role in minimizing these defects.
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
TECHNICAL TRAINING MANUAL GENERAL FAMILIARIZATION COURSEDuvanRamosGarzon1
AIRCRAFT GENERAL
The Single Aisle is the most advanced family aircraft in service today, with fly-by-wire flight controls.
The A318, A319, A320 and A321 are twin-engine subsonic medium range aircraft.
The family offers a choice of engines
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.