In this presentation you can able to understand what is split and strip plot design along with that steps to forming ANOVA table and further calculation for critical differences by which you can determine whether the treatment is on par with other
2. SPLIT PLOT DESIGN
• A split-plot design is an experimental design
in which researchers are interested in studying
two factors in which:
One of the factors is “easy” to change or vary.
One of the factors is “hard” to change or vary.
• This type of design was developed in 1925 by
mathematician Ronald Fisher for use in
agricultural experiments.
3. • It occurs in factors which require larger plots than
for others.
• Eg: Experiments on Tillage and Irrigation require
larger plots whereas experiments on Fertilizers
and Herbicides require no larger plots.
• Larger plots are split into smaller plots to
accommodate the other factors; different
treatment where alloted at random to their
respective plots – Split plot design.
5. CRITICAL DIFFERENCE
• Critical Difference is used to compare means
of different treatments that have an equal
number of replications.
6. • Treatment 1 (T1) is significantly different from Treatment 2 (T2) as their difference is
more than the Critical Difference you have calculated here. (T1-T2 i.e. 10.62 – 5.21 =
5.41 > 0.978887)
• But Treatment 1 (T1) statistically does not differ significantly from Treatment 6 (T6),
as their difference is less than the Critical Difference you have calculated here (T1-T6
i.e. 10.62 – 10.25 = 0.37 < 0.978887)
7. 1. As Treatment 1 (T1) significantly out-yielded -
Treatment (T2) and will likely do so again in
future field trials,
2. But as Treatment 1 (T1) statistically does not
differ significantly from Treatment 6 (T6) i.e.
Treatment 1 (T1) was statistically similar to
Treatment 6 (T6). so
– The treatment effects on yield were similar
– The observed differences are likely due to
simply random chance or background "noise,"
and
– The apparent trends in treatment yields (T1>T6)
would likely not be repeated in subsequent trials
comparing these same treatments.
8. CONFIDENCE LEVEL
• The confidence level, which we usually take
either 90 or 95 percent.
• Confidence level can be identified by its
corresponding alpha value:
• A 95 percent confidence level has an alpha of 5
% (p < 0.05)
• and a 90 percent confidence level has
an alpha of 10 % (p< 0.1).
• A 90 percent confidence level means there is still
a 10 percent chance that, the difference was
actually due to natural variation.
28. STRIP PLOT DESIGN
• This design is also known as split block design. When
there are two factors in an experiment and both the
factors require large plot sizes it is difficult to carryout
the experiment in split plot design.
• Also the precision for measuring the interaction effect
between the two factors is higher than that for
measuring the main effect of either one of the two
factors. Strip plot design is suitable for such
experiments.
• In strip plot design each block or replication is divided
into number of vertical and horizontal strips depending
on the levels of the respective factors.
29. • In this split-plot design, Irrigation was implemented first followed by
a split into two parts. Two fertilizers were randomized among the
split plots.
In the split-block design, the “plots” are split
horizontally and vertically according to how many levels are present
in the experiment. In other words, the first, whole-plot factor is
completely crossed with a second factor.
30. Compute Correction Factor = (GT)²
-------------
a X b X r
TSS = Σyijk ²- CF
Trt SS = ΣYij²/r - CF
Blk SS= ΣY..k²/ ra - CF
31. 1) Vertical Strip Analysis
Form A x R Table and calculate RSS, ASS and
Error(a) SS
32.
33. 2) Horizontal Strip Analysis
• Form B x R Table and calculate RSS, BSS and Error(b)
SS