Sewing Machine Needle A to Z
written by
Md. Masudur Rahman
Department of Textile Engineering
4th Batch
National Institute of Textile Engineering and Research (NITER)
Contents…… . . .
The basic functions of a needle
Needle Parts
Needle Selection
Types of needle
Needle Size / Thickness
Various effects of wrong sewing needle selection in apparel industry has mentioned in the below:
1. When the needle is finer than sewing thread
2. When the thread is finer than needle
3. When the needle is coarser than required fabric
4. When the needle is finer than required fabric
Needle Parts:
1. Butt
The starting part of bottom edge of needle. Helps for easily attaching of needle with the needle bar or clamp
2. Shank
The bottom thicker part of the needle which is tied in the needle clamp or the needle set screw. It may be cylindrical or flat in size. It supports the needle as a whole by providing additional strength
3. Shoulder
The intermediate section between the shank and the blade of needle. When the needle penetrate through the fabric to reach its lower position, then the shoulder also penetrates through the fabric. As a result it reduces the friction between needle & fabrics by producing a wider hole on fabric.
4. Blade
The needle portion extends from the shank to the eye. This is subjected to the greatest amount of friction and hence heat when it passes through the material. Blade is gradually tapered to tip
5. Long groove(s)
It is a long and thin groove, presents in one side of the needle blade . During up and down of needle through sewing, the sewing thread take place in this groove and reduce the frictions between fabric, needle and thread. It provides a protective channel and reduce possibility of damaging thread due to frictions.
6. Short groove
It is formed on the other side of long groove, towards the shuttle, hook, or looper and it assists in throwing the loop of needle thread
7. Eye
The eye of the needle is present in the bottom end of the blade. Needle thread allowed through this eye is taken to the bottom area. It helps to create loop
8. Scarf (Clearance)
It is a curved slot, a clearance cut in the needle blade just above the eye to permit a closer setting of the shuttle, hook, or looper to the needle. As a result, it is easy to catch the needle loop by the looper hook.
9. Point
It is the part from needle eye to the tip. The point of the needle is shaped to provide the most suitable penetration of the material being sewn according to its nature and the desired stitch effect
10. Tip
The ending edge pf needle is called tip. It helps to penetrate the needle into the fabric and create hole during sewing.
Sewing Machine Needle A to Z
written by
Md. Masudur Rahman
Department of Textile Engineering
4th Batch
National Institute of Textile Engineering and Research (NITER)
Contents…… . . .
The basic functions of a needle
Needle Parts
Needle Selection
Types of needle
Needle Size / Thickness
Various effects of wrong sewing needle selection in apparel industry has mentioned in the below:
1. When the needle is finer than sewing thread
2. When the thread is finer than needle
3. When the needle is coarser than required fabric
4. When the needle is finer than required fabric
Needle Parts:
1. Butt
The starting part of bottom edge of needle. Helps for easily attaching of needle with the needle bar or clamp
2. Shank
The bottom thicker part of the needle which is tied in the needle clamp or the needle set screw. It may be cylindrical or flat in size. It supports the needle as a whole by providing additional strength
3. Shoulder
The intermediate section between the shank and the blade of needle. When the needle penetrate through the fabric to reach its lower position, then the shoulder also penetrates through the fabric. As a result it reduces the friction between needle & fabrics by producing a wider hole on fabric.
4. Blade
The needle portion extends from the shank to the eye. This is subjected to the greatest amount of friction and hence heat when it passes through the material. Blade is gradually tapered to tip
5. Long groove(s)
It is a long and thin groove, presents in one side of the needle blade . During up and down of needle through sewing, the sewing thread take place in this groove and reduce the frictions between fabric, needle and thread. It provides a protective channel and reduce possibility of damaging thread due to frictions.
6. Short groove
It is formed on the other side of long groove, towards the shuttle, hook, or looper and it assists in throwing the loop of needle thread
7. Eye
The eye of the needle is present in the bottom end of the blade. Needle thread allowed through this eye is taken to the bottom area. It helps to create loop
8. Scarf (Clearance)
It is a curved slot, a clearance cut in the needle blade just above the eye to permit a closer setting of the shuttle, hook, or looper to the needle. As a result, it is easy to catch the needle loop by the looper hook.
9. Point
It is the part from needle eye to the tip. The point of the needle is shaped to provide the most suitable penetration of the material being sewn according to its nature and the desired stitch effect
10. Tip
The ending edge pf needle is called tip. It helps to penetrate the needle into the fabric and create hole during sewing.
sewing thread is a flexible, small diameter yarn or strand usually treated with a surface coating, lubricant or both, intended to be used to stitch one or more pieces of material or an object to a material.
Implicitly or explicitly all competing businesses employ a strategy to select a mix
of marketing resources. Formulating such competitive strategies fundamentally
involves recognizing relationships between elements of the marketing mix (e.g.,
price and product quality), as well as assessing competitive and market conditions
(i.e., industry structure in the language of economics).
Affordable Stationery Printing Services in Jaipur | Navpack n PrintNavpack & Print
Looking for professional printing services in Jaipur? Navpack n Print offers high-quality and affordable stationery printing for all your business needs. Stand out with custom stationery designs and fast turnaround times. Contact us today for a quote!
Business Valuation Principles for EntrepreneursBen Wann
This insightful presentation is designed to equip entrepreneurs with the essential knowledge and tools needed to accurately value their businesses. Understanding business valuation is crucial for making informed decisions, whether you're seeking investment, planning to sell, or simply want to gauge your company's worth.
Kseniya Leshchenko: Shared development support service model as the way to ma...Lviv Startup Club
Kseniya Leshchenko: Shared development support service model as the way to make small projects with small budgets profitable for the company (UA)
Kyiv PMDay 2024 Summer
Website – www.pmday.org
Youtube – https://www.youtube.com/startuplviv
FB – https://www.facebook.com/pmdayconference
Improving profitability for small businessBen Wann
In this comprehensive presentation, we will explore strategies and practical tips for enhancing profitability in small businesses. Tailored to meet the unique challenges faced by small enterprises, this session covers various aspects that directly impact the bottom line. Attendees will learn how to optimize operational efficiency, manage expenses, and increase revenue through innovative marketing and customer engagement techniques.
Company Valuation webinar series - Tuesday, 4 June 2024FelixPerez547899
This session provided an update as to the latest valuation data in the UK and then delved into a discussion on the upcoming election and the impacts on valuation. We finished, as always with a Q&A
Discover the innovative and creative projects that highlight my journey throu...dylandmeas
Discover the innovative and creative projects that highlight my journey through Full Sail University. Below, you’ll find a collection of my work showcasing my skills and expertise in digital marketing, event planning, and media production.
LA HUG - Video Testimonials with Chynna Morgan - June 2024Lital Barkan
Have you ever heard that user-generated content or video testimonials can take your brand to the next level? We will explore how you can effectively use video testimonials to leverage and boost your sales, content strategy, and increase your CRM data.🤯
We will dig deeper into:
1. How to capture video testimonials that convert from your audience 🎥
2. How to leverage your testimonials to boost your sales 💲
3. How you can capture more CRM data to understand your audience better through video testimonials. 📊
B2B payments are rapidly changing. Find out the 5 key questions you need to be asking yourself to be sure you are mastering B2B payments today. Learn more at www.BlueSnap.com.
What is the TDS Return Filing Due Date for FY 2024-25.pdfseoforlegalpillers
It is crucial for the taxpayers to understand about the TDS Return Filing Due Date, so that they can fulfill your TDS obligations efficiently. Taxpayers can avoid penalties by sticking to the deadlines and by accurate filing of TDS. Timely filing of TDS will make sure about the availability of tax credits. You can also seek the professional guidance of experts like Legal Pillers for timely filing of the TDS Return.
3. Seam Engineering
•It includes seam and stitch
construction.
•The more thread a stitch consumes,
the greater is the strength!
•This is clearly visible when we
compare lock stitch and chain stitch.
•Lock stitch is one in which thread
is locked both sides of the fabric and
starts with 301 lock stitch.
•It go through more shearing as
compared to chain stitch and over
edge stitch.
•As in lockstitch threads are
interlocked rather than inter-
looped
5. a. Quality is the customers' perception (awareness)
of the value of the suppliers' work output.
b. In manufacturing, quality is a practical explanation
as the non-conformity of product ; it is also defined
as fitness for purpose.
c. To Support personnel measure quality in the
degree that a product is reliable, maintainable, or
sustainable. A quality item has the ability to
perform satisfactorily in service and is suitable for
its intended (planned) purpose.
d. For the Textile & Apparel industry, product quality
is calculated in terms of quality & standard of
fibers, yarns, fabric construction, color fastness,
designs and the final finished garments.
e. Etc..
Quality?Quality?
7. Fabric OZ/Sq. Yd. Grams/ SQ. Mtr thread Tex size needle Size
Ex. Light 2 -4 oz. 68 – 136gr. Tex 16, 18, 21, 24 60, 65
Light 4-6 oz. 136 – 204gr. Tex 24, 27, 30 70, 75
Medium 6-8 oz. 204 – 272gr. Tex 30, 35, 40 80, 90, 100
Med. Heavy 8 -10 oz. 272 – 339gr. Tex 40, 45, 50, 60 100, 110
heavy 10-12 oz. 339 – 407gr. Tex 60, 80, 90, 105 120, 140
Ex. Heavy 12 -14 oz. 407 – 475gr. Tex 105, 120, 135 + 140, 160
Related >> Fabric Weight / Typical Thread Sizes / Needle Sizes
8. Common Seam Example : All Types…Common Seam Example : All Types…
Stitch Type matrix
PDF File
Needle Types PDF
File
Decorative Stitch
matrix
9. Common Seam Quality defects: Stitch Balance 301 lock stitch
DESCRIPTION: Where loops are seen
either on the bottom side or topside of
the seam. This is particularly evident
with different colored needle and bobbin
threads. Also, where the stitch is too
loose.
SOLUTIONS: 1) Use a quality thread
with consistent frictional characteristics;
2) Properly balance the stitch so that the
needle and bobbin threads meet in the
middle of the seam. Always start by
checking the bobbin thread tension to
make sure it is set correctly, so that the
minimum thread tension is required to
get a balanced stitch.
Poor Stitch Balance - Too Loose
10. Common Seam Quality Defects,
Improper Stitch Balance - 401 Chain stitch
DESCRIPTION: Where the loops on
the bottom-side of the seam are
inconsistent and do not appear
uniform.
SOLUTIONS:
1) Use a quality thread with consistent
frictional characteristics;
2) Properly balance the stitch so that
when the lopper thread is unraveled,
the needle loop lays over half way to
the next needle loop on the underside
of the seam.
Stitch Too Loose
Proper Stitch Balance
11. Common Seam Quality Defects
Improper Stitch Balance - 504 Overedge Stitch
DESCRIPTION: Where the needle
loop is not pulled up to the underside
of the seam and the "purl" is not on the
edge of the seam.
SOLUTIONS: 1) Use a quality thread
with consistent frictional
characteristics;
2) Properly balance the stitch so that
when the looper thread is unraveled,
the needle loop lays over half way to
the next needle loop on the underside
of the seam.
Improper Stitch Balance
Proper Stitch Balance
12. Needle Cutting on Knits
DESCRIPTION: Where needle
holes appear along the stitch line
that will eventually turn into a
"run". Generally caused by the
needle damaging the fabric as it is
penetrating the seam.
MINIMIZING NEEDLE CUTTING
ON KNITS:
1) Make sure the proper thread
size and needle type and size are
being used for the fabric
2) Make sure the fabric has been
properly stored to prevent drying
out and has been finished
properly;
3) Check with your fabric
manufacturer
13. Description:
Where the stitch line is still intact but the yarns in the fabric have ruptured.
MINIMIZING SEAM FAILURES - FABRIC:
1) Reinforce stress points with Bartacks. Make sure the bartacks are the proper length and
width for the application;
2) Check to make sure the patterns have been designed for proper fit;
3) Make sure the ideal seam construction is being used
4) Contact your fabric supplier.
Open Seam Failure - Fabric
Bartacks Used to Reinforce Fly Seam
14. DESCRIPTION:
Where the yarns in the fabric pull out of the seam from the edge. This often
occurs on fabrics constructed of continuous filament yarns that are very smooth and
have a slick surface. Also caused by loosely constructed fabrics.
MINIMIZING SEAM FAILURES - SEAM SLIPPAGE:
1) Consider changing the seam construction to a French seam construction; 2)
Increase the seam width or width of bite; 3) Optimize the stitches per inch; 4)
Contact your fabric supplier.
16. DESCRIPTION: Where the seam does
not lay flat after stitching.
SOLUTIONS:
1) If sewing machines are equipped
with differential feed, set them properly
for the fabric;
2) Use minimum presser foot pressure
during sewing; and
3) Observe operator for correct
handling techniques. Too much
stretching of the fabric by the sewing
operator will cause this problem.
17. DESCRIPTION: Where the seam does
not lay flat and smooth along the stitch
line. Caused by one of the following:
1) Feed Puckering - where the plies of
fabric in the seam are not being
aligned properly during sewing;
2) Tension Puckering - where the
thread has been stretched and sewn
into the seam. The thread then causes
the seam to draw back and pucker;
3) Yarn Displacement or structural
jamming - caused by sewing seams
with too large of thread that causes the
yarns in the seam to be displaced,
giving a puckered appearance.
18.
19. DESCRIPTION: Where the edge of the
seam is either extremely "ragged" or
"rolls" inside the stitch.
SOLUTIONS: 1) Make sure the sewing
machine knives are sharpened and
changed often; 2) The knives should
be adjusted properly in relationship to
the "stitch tongue" on the needle plate
to obtain the proper seam width or
width bite. In the photo, the trimming
knives have been set wider than the
"stitch tongue" on the needle plate
causing the "ropy" appearance.
20. DESCRIPTION: Where a "joint" occurs
on the stitch line. If this occurs on
Topstitching, then the seam does not
appear to be 1st quality merchandise.
Caused by 1) thread breaks or thread
run-out during sewing; or 2) cut or broken
stitches during a subsequent treatment of
the finished product (i.e., stone
washing).
MINIMIZING THREAD BREAKAGE: 1)
Use a better quality sewing thread. This
will help to minimize sewing interruptions.
and/or Minimizing Thread Breakage &
Skipped Stitches
2) Insure proper machine maintenance
and sewing machine adjustments; 3)
Make sure sewing machines are properly
maintained and adjusted for the fabric
and sewing operation. 4) Observe sewing
operators for correct material handling
techniques.
21. DESCRIPTION: Where the stitch
balance is not properly adjusted (stitch
too loose) and you can see the seam
opening up. To check for Seam Grin,
apply normal seam stress across the
seam and then remove the stress. If
the seam remains opened, then the
seam has too much "grin through".
SOLUTIONS: To correct, readjust the
sewing machine thread tensions so
that the proper stitch balance is
achieved. Too much tension will cause
other problems including seam failures
("Stitch Cracking"), excessive thread
breakage, and skipped stitches.
22. DESCRIPTION: Where the stitch length is inconsistent, possibly
appearing as double the normal stitch length; or where you can see that
the threads in the stitch are not properly connected together. Caused by
the stitch forming device in the sewing machine missing the thread loop
during stitch formation causing a defective stitch. On looper type
stitches, this will allow the stitch to unravel causing seam failure.
MINIMIZING SKIPPED STITCHES: 1) Use a better quality sewing
thread & Top stitch on the inside sewing allowance . This will include a
higher performance thread designed to minimize sewing interruptions.
2) Insure proper machine maintenance and sewing machine
adjustments; 3) Make sure sewing machines are properly maintained
and adjusted for the fabric and sewing operation. 4) Observe sewing
operators for correct material handling techniques.
23. 301 Lockstitch Seams
For 301 lockstitch seams, Generally recommend using the same needle thread size
as the bobbin thread size in the seam. Why? Because “a chain is only as strong as
its weakest link.”
If a smaller, weaker thread is used in the bobbin, then the seam will only be as
strong as the bobbin thread. This is particularly true with lockstitch seams because
of the way the needle and bobbin threads are interlocked together.
This does have exceptions. Sometimes a smaller size thread with a different fiber
type and/or thread construction can be used and still maintain seam performance.
An example would be to use a higher tenacity Corespun in place of a Spun thread.
To take this a step further, you can use an Anecord Nylon® monocord bobbin
instead of a spun or corespun thread in the seam. Also, exceptions can be made
when a larger topstitching thread is desired to give a bold appearance on the
outside of the garment when it is not necessarily being used to add strength or
durability to the seam.
24. Common Seam Class Example : 400 & 401 lock stitchCommon Seam Class Example : 400 & 401 lock stitch
25. 504 Overedge Seams
504 Overedge seams have basically the
same needle thread formation as the
needle thread on a 401 chainstitch
seam. Therefore, the same rule
applies. You can use a looper thread
approximately 60% of the needle thread
size without adversely affecting the
seam strength (for example: T-24 needle
thread – T-18 looper threads). Just
remember that smaller looper threads
will not give the seam coverage of larger
thread sizes.
Factors that Affect Seam Strength
Five factors that determine the strength of a
seam include:
Fabric type and weight.
Thread fiber type, construction, and size.
Stitch and seam construction.
Stitches per inch.
Stitch balance.
26. DESCRIPTION: Where a tail
of thread is visible on the
topside of the button and when
pulled, the button falls off.
SOLUTIONS: 1) Use a quality
sewing thread to minimize
skipped stitches; 2) Specify
attaching the buttons with a
Lockstitch instead of a single
thread Chain stitch Buttons
sewing machine.
27. STITCH ESTIMATING GUIDE:
1 square inch of “Fill” stitches at a
normal density with a stitch of
6mm = 1000 stitches. This is for a
basic fill to cover an area with no
stitching on top.
1 square inch of “Fill” stitches at a
normal density with a stitch of 4
mm = 1500 stitches.
This is for a basic “Fill” to cover an area
that would have lettering or other
stitching on top. The stitch length is
shortened to prevent the stitches from
pulling apart when the additional
stitching is put on top.
28. DESCRIPTION:
Used to cover large areas. There are
many different “Fill” stitch patterns
and they can differ in direction, angle,
and pattern. “Fill” stitches are
used to cover large areas. (Also
known as Tatami stitches.) With
today’s modern digitizing programs,
there are many “Fill” stitch patterns
that can be selected to give varying
design appearance. Curved, fill
stitches are becoming more popular in
the industry. Using a “Fill” stitch in a
curve can add more dimension to a
design. This type of stitch is very
useful for hair and water.
29. DESCRIPTION:
Consists of forming three stitches between two
points primarily used for outlining work. “Bean”
stitches are more pronounced than Running
Stitches.
STITCH ESTIMATING GUIDE:
Triple Running Line (Bean Stitch) = 37 per inch
30. DESCRIPTION:
Consist of a single line of stitching
primarily used for outlining and detail
work. They are also used as the
foundation of most “underlays” and
“Fill” stitches. Areas that are under
1mm in width are usually done with a
running stitch.
STITCH ESTIMATING GUIDE:
Single Running Line = 12 per inch
Double Running Line = 25 per inch
(Normal Outlining Stitches)
Triple Running Line (Bean Stitch) = 37 per
inch
4-Ply Running Line = 48 per inch
(Alternative to Satin Stitch
31. The friction between the needle blade and the
fabric creates needle heat. The following
factors can have an impact on the amount of
heat that is generated:
Fabric thickness
Fabric finish or density
Fabric color or density (darker colors normally
are worse than lighter colors)
Sewing machine speed
Needle contact surface
Needle Size or diameter
Needle length
Type of needle blade
Type of needle finish
Needle heat is usually more of a problem when
sewing either synthetic threads and / or
synthetic fabrics and can cause excessive
thread breakage and / or damage to the fabric
being sewn.
32. The thread characteristics that impact loop formation include:
Elongation or stretchiness of the thread.
Initial modulus or initial resistance to stretching.
Twist direction & twist level.
Liveliness of the thread.
Frictional characteristics needed to set a balanced stitch
If the needle size - thread size relationship is improper, the thread will not be properly
clamped on the scarf side of the needle and poor loop formation will occur. If the seam is
not held in a stationary position when the needle is rising, the seam will rise with the
needle and not form a proper needle loop. This condition, called flagging, is one of the
most common causes of skipped stitches and thread breakage.
33. The physical properties in thread that impact how much the thread is stretched during the
sewing process include:
Elongation properties of the fiber being used.
Frictional characteristics of the thread needed to set a balanced stitch.
Note: Regardless of the type of thread being used, as more and more tension is applied to
the thread, the thread will stretch more, affecting loop formation. Improper loop
formation will result in a higher frequency of sewing interruptions. This is why it is
recommended to always adjust the sewing machines thread handling system to sew with
minimum thread tension.
Below is a recommended procedure for balancing the stitch on a any sewing machine:
Set the bottom tension (bobbin or looper) to a minimum that still forms a consistent
stitch.
Reduce the needle thread tension until the stitch appears to be loose on the bottom side
of the seam then tighten the top tension until a balanced stitch is achieved.
34. Seam elasticity can be accomplished by a combination of having the
correct number of stitches per inch and having the proper stitch balance.
The more stretch the fabric has, the more stitches per inch that are
required. Common ranges of stitches per inch are from 12 to 14 spi.