With rising crude prices and depleting quality of crude, however, the level of wastewater pollutants in petroleum wastewater is at new high. Such conditions are forcing refineries to use a more advanced water treatment, water recovery methods, and robust processes that work well under a variety of conditions and can handle the changing refinery effluent flow rates. Finally a process that is economical in overall life time cost is needed to make all of this feasible. Aquatech has experience working with these refinery effluent pollutants in the refinery market and offers the advanced petroleum wastewater treatment and recovery technology necessary for the refinery’s needs.
Treatment of Effluents from Petroleum RefineriesAsheesh Padiyar
A brief power point presentation on the Effluent treatment from Petroleum Refineries for a Chemical Engineer.Chemical Engineers are also involved in the water treatment , and is of huge concern with the amount of water needed / contaminated during the refinery mass transfer operations.
Effluent Treatment Plant Design, Operation And Analysis Of Waste Water Jaidev Singh
Contents
1. Introduction to Effluent Treatment Plant (ETP)
1.1 Use of water in industries
1.2 Industrial waste water sources
1.3 Effluent Treatment Plant
1.4 National Standards for waste water
1.5 What do these standards means?
1.6 Waste water treatment
1.7 Planning an Effluent Treatment Plant : Factors to Consider
2. Treatment Methods
2.1 Physical Unit Operations
2.2 Chemical Unit Processes
2.3 Biological Unit Processes
3. Operation and control
3.1 Mixed liquor suspended solids
3.2 Sludge Volume Index and Sludge Density Index
3.3 Sludge Age; Mean Cell Residence Time (MCRT)
3.4 Food/Mass Ratio
3.5 Constant MLSS
3.6 Return Activated Sludge Control (RAS)
4. Choosing an Effluent Treatment Plant
4.1 Biological Treatment
4.2 Physico-Chemical Treatment
4.3 Physico-Chemical and Biological Treatment
4.4 Area Requirement Comparison
4.5 Cost Comparison
5. Chemical Analysis of Waste Water
5.1 Commonly used chemicals
5.2 Chemical Tests and procedures
Lecture notes of Industrial Waste Treatment (Elective -III) as per syllabus of Solapur university for BE Civil
Prepared by
Prof S S Jahagirdar,
Associate Professor,
N K ORchid College of Engg and Tech,
Solapur
With rising crude prices and depleting quality of crude, however, the level of wastewater pollutants in petroleum wastewater is at new high. Such conditions are forcing refineries to use a more advanced water treatment, water recovery methods, and robust processes that work well under a variety of conditions and can handle the changing refinery effluent flow rates. Finally a process that is economical in overall life time cost is needed to make all of this feasible. Aquatech has experience working with these refinery effluent pollutants in the refinery market and offers the advanced petroleum wastewater treatment and recovery technology necessary for the refinery’s needs.
Treatment of Effluents from Petroleum RefineriesAsheesh Padiyar
A brief power point presentation on the Effluent treatment from Petroleum Refineries for a Chemical Engineer.Chemical Engineers are also involved in the water treatment , and is of huge concern with the amount of water needed / contaminated during the refinery mass transfer operations.
Effluent Treatment Plant Design, Operation And Analysis Of Waste Water Jaidev Singh
Contents
1. Introduction to Effluent Treatment Plant (ETP)
1.1 Use of water in industries
1.2 Industrial waste water sources
1.3 Effluent Treatment Plant
1.4 National Standards for waste water
1.5 What do these standards means?
1.6 Waste water treatment
1.7 Planning an Effluent Treatment Plant : Factors to Consider
2. Treatment Methods
2.1 Physical Unit Operations
2.2 Chemical Unit Processes
2.3 Biological Unit Processes
3. Operation and control
3.1 Mixed liquor suspended solids
3.2 Sludge Volume Index and Sludge Density Index
3.3 Sludge Age; Mean Cell Residence Time (MCRT)
3.4 Food/Mass Ratio
3.5 Constant MLSS
3.6 Return Activated Sludge Control (RAS)
4. Choosing an Effluent Treatment Plant
4.1 Biological Treatment
4.2 Physico-Chemical Treatment
4.3 Physico-Chemical and Biological Treatment
4.4 Area Requirement Comparison
4.5 Cost Comparison
5. Chemical Analysis of Waste Water
5.1 Commonly used chemicals
5.2 Chemical Tests and procedures
Lecture notes of Industrial Waste Treatment (Elective -III) as per syllabus of Solapur university for BE Civil
Prepared by
Prof S S Jahagirdar,
Associate Professor,
N K ORchid College of Engg and Tech,
Solapur
In this presentation, application of some parameters of water wwater analysis (i.e., Acidity, Sulfate, Volatile Acid,Nitrogen,greases and oils) , procedure to measure that parameter, environmental significance of that parameter and importance of that parameter in waste water analysis.
Lecture note of Industrial Waste Treatment (Elective -III) as per syllabus of Solapur university for BE Civil
Prepared by
Prof S S Jahagirdar,
Associate Professor,
N K ORchid College of Engg and Tech,
Solapur
INDUSTRIAL WASTE TREATMENT IN STEEL INDUSTRYSreya P S
The steel industry is one of the most important industries in India.
The main environmental issues faced by Steel Industry are:
Air emissions
Wastewater
Solid Waste
Industrial waste water purification procedurepasindulaksara1
The effluent Treatment Plant (ETP) is a method that is used to treat the emanation coming out from many areas of the plant. It includes biological, physical, and chemical processes. It aims to releasing safe water into the environment to prevent it from getting cop0ntaminated. These plants are have been very useful in the process of providing clean water to the environment and have conserved water in a number of ways.
In this presentation, application of some parameters of water wwater analysis (i.e., Acidity, Sulfate, Volatile Acid,Nitrogen,greases and oils) , procedure to measure that parameter, environmental significance of that parameter and importance of that parameter in waste water analysis.
Lecture note of Industrial Waste Treatment (Elective -III) as per syllabus of Solapur university for BE Civil
Prepared by
Prof S S Jahagirdar,
Associate Professor,
N K ORchid College of Engg and Tech,
Solapur
INDUSTRIAL WASTE TREATMENT IN STEEL INDUSTRYSreya P S
The steel industry is one of the most important industries in India.
The main environmental issues faced by Steel Industry are:
Air emissions
Wastewater
Solid Waste
Industrial waste water purification procedurepasindulaksara1
The effluent Treatment Plant (ETP) is a method that is used to treat the emanation coming out from many areas of the plant. It includes biological, physical, and chemical processes. It aims to releasing safe water into the environment to prevent it from getting cop0ntaminated. These plants are have been very useful in the process of providing clean water to the environment and have conserved water in a number of ways.
Effluent Treatment Plant
What is ETP
Need fo ETP
Design of ETP
Design of ETP
Sludge treatment process
Flowchart of ETP
Case study of ETP
ETP plant operation
Textile plant ETP
Equalization
Sedimentation
Settlers
Sludge treatment process
Flowchart of ETP
Case study of ETP
ETP plant operation
Textile plant ETP
Equalization
Sedimentation
Settlers
PH adjustment
Biochemical Process as a means to Control and Mitigate Industrial Wastewate...Mohammad Dain Shah Munna
Biochemical Process as a means to Control and Mitigate Industrial Wastewater
Mohammad Dain Shah Munna
Applied Chemistry and Chemical Engineering
University of Chittagong
The efficient disposal of effluent from meat plants and meat-processing works is important because of the possible pollution of water – courses. Hence an effluent treatment plant (ETP) is necessary in all modern abattoirs/meat plants. The objective of effluent treatment is to produce a product that can be safely discharged into a waterway or sewer in compliance with the recommended limits for discharge.
SUGAR MANUFACTURING PROCESS
=washing
=cutting & shredding
=extraction of juice
=purification of juice
1.Defaction
2.Coagulation
3.Chemical Reaction
4.Filtration
5.Carbonation
6.Sulphitation
7.Chemical reaction
=concentration on juice
=crystallization
=refining of sugar
1.Raw sugar
2.Refining of sugar
=drying & packing
= Sugar manufacturing flow diagram
=Waste water generation source during the sugar manufacturing process
=Waste water characteristics
ESTIMATION OF CHARACTERSTICS OF WASTEWATERzabby2407
TO KNOW ABOUT WASTEWATER & VARIOUS KINDS OF POLLUTANTS PRESENT IN IT.
CATEGORIES ARE:
PHYSICAL
CHEMICAL
BIOLOGICAL
RADIOLOGICAL
& ESTIMATION OF VARIOUS POLLUTANTS BY VARIOUS TEST.
Similar to Oil Refinery Waste water treatment Plant (20)
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...Amil Baba Dawood bangali
Contact with Dawood Bhai Just call on +92322-6382012 and we'll help you. We'll solve all your problems within 12 to 24 hours and with 101% guarantee and with astrology systematic. If you want to take any personal or professional advice then also you can call us on +92322-6382012 , ONLINE LOVE PROBLEM & Other all types of Daily Life Problem's.Then CALL or WHATSAPP us on +92322-6382012 and Get all these problems solutions here by Amil Baba DAWOOD BANGALI
#vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore#blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #blackmagicforlove #blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #Amilbabainuk #amilbabainspain #amilbabaindubai #Amilbabainnorway #amilbabainkrachi #amilbabainlahore #amilbabaingujranwalan #amilbabainislamabad
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
Courier management system project report.pdfKamal Acharya
It is now-a-days very important for the people to send or receive articles like imported furniture, electronic items, gifts, business goods and the like. People depend vastly on different transport systems which mostly use the manual way of receiving and delivering the articles. There is no way to track the articles till they are received and there is no way to let the customer know what happened in transit, once he booked some articles. In such a situation, we need a system which completely computerizes the cargo activities including time to time tracking of the articles sent. This need is fulfilled by Courier Management System software which is online software for the cargo management people that enables them to receive the goods from a source and send them to a required destination and track their status from time to time.
Automobile Management System Project Report.pdfKamal Acharya
The proposed project is developed to manage the automobile in the automobile dealer company. The main module in this project is login, automobile management, customer management, sales, complaints and reports. The first module is the login. The automobile showroom owner should login to the project for usage. The username and password are verified and if it is correct, next form opens. If the username and password are not correct, it shows the error message.
When a customer search for a automobile, if the automobile is available, they will be taken to a page that shows the details of the automobile including automobile name, automobile ID, quantity, price etc. “Automobile Management System” is useful for maintaining automobiles, customers effectively and hence helps for establishing good relation between customer and automobile organization. It contains various customized modules for effectively maintaining automobiles and stock information accurately and safely.
When the automobile is sold to the customer, stock will be reduced automatically. When a new purchase is made, stock will be increased automatically. While selecting automobiles for sale, the proposed software will automatically check for total number of available stock of that particular item, if the total stock of that particular item is less than 5, software will notify the user to purchase the particular item.
Also when the user tries to sale items which are not in stock, the system will prompt the user that the stock is not enough. Customers of this system can search for a automobile; can purchase a automobile easily by selecting fast. On the other hand the stock of automobiles can be maintained perfectly by the automobile shop manager overcoming the drawbacks of existing system.
Democratizing Fuzzing at Scale by Abhishek Aryaabh.arya
Presented at NUS: Fuzzing and Software Security Summer School 2024
This keynote talks about the democratization of fuzzing at scale, highlighting the collaboration between open source communities, academia, and industry to advance the field of fuzzing. It delves into the history of fuzzing, the development of scalable fuzzing platforms, and the empowerment of community-driven research. The talk will further discuss recent advancements leveraging AI/ML and offer insights into the future evolution of the fuzzing landscape.
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
COLLEGE BUS MANAGEMENT SYSTEM PROJECT REPORT.pdfKamal Acharya
The College Bus Management system is completely developed by Visual Basic .NET Version. The application is connect with most secured database language MS SQL Server. The application is develop by using best combination of front-end and back-end languages. The application is totally design like flat user interface. This flat user interface is more attractive user interface in 2017. The application is gives more important to the system functionality. The application is to manage the student’s details, driver’s details, bus details, bus route details, bus fees details and more. The application has only one unit for admin. The admin can manage the entire application. The admin can login into the application by using username and password of the admin. The application is develop for big and small colleges. It is more user friendly for non-computer person. Even they can easily learn how to manage the application within hours. The application is more secure by the admin. The system will give an effective output for the VB.Net and SQL Server given as input to the system. The compiled java program given as input to the system, after scanning the program will generate different reports. The application generates the report for users. The admin can view and download the report of the data. The application deliver the excel format reports. Because, excel formatted reports is very easy to understand the income and expense of the college bus. This application is mainly develop for windows operating system users. In 2017, 73% of people enterprises are using windows operating system. So the application will easily install for all the windows operating system users. The application-developed size is very low. The application consumes very low space in disk. Therefore, the user can allocate very minimum local disk space for this application.
Explore the innovative world of trenchless pipe repair with our comprehensive guide, "The Benefits and Techniques of Trenchless Pipe Repair." This document delves into the modern methods of repairing underground pipes without the need for extensive excavation, highlighting the numerous advantages and the latest techniques used in the industry.
Learn about the cost savings, reduced environmental impact, and minimal disruption associated with trenchless technology. Discover detailed explanations of popular techniques such as pipe bursting, cured-in-place pipe (CIPP) lining, and directional drilling. Understand how these methods can be applied to various types of infrastructure, from residential plumbing to large-scale municipal systems.
Ideal for homeowners, contractors, engineers, and anyone interested in modern plumbing solutions, this guide provides valuable insights into why trenchless pipe repair is becoming the preferred choice for pipe rehabilitation. Stay informed about the latest advancements and best practices in the field.
3. SCOPE OF DISCUSSION
CLASSIFICATION OF WASTES
REFINERY EFFULENT CHARACTERSTICS
TREATMENT TECHNIQUES
PROCESS DESIGN PHILOSPHY
WASTE WATER TREATMENT PLANT IN
GENERAL
4. Water used by homes, industry, business must be
treated before released back to the environment
Waste Water Generation
8. EXPLANATIONS:
1. Assuming minimum dilution 1:10 on discharge, lower ratio would attract
progressively stringent standards to be determined by the Federal
Environmental Protection Agency. By 1:10 dilution means, for example that for
each one cubic meter of treated effluent, the recipient water body should have
10 cubic meter of water for dilution of this effluent.
2. Modified Benzene Alkyl Sulphate; assuming surfactant as biodegradable.
3. Pesticides include herbicides, fungicides and insecticides.
4. Subject to total toxic metals discharge should not exceed level given at S.No.25
5. Applicable only when and where sewage treatment is operational and BOD5=80
mg/lit is achieved by the sewage treatment system.
6. Provided discharge is not at shore and not within 10 miles of mangrove or other
important estuaries.
9. ENVIRONMENTAL THREATS FROM INDUSTRIAL
WASTE
WATER POLLUTANTS
Total Suspended Solid (TSS)
Biochemical Oxygen Demand (BOD)
Chemical Oxygen Demand (COD
Oil and Grease
Total Dissolve Solids (TDS)
Toxic Chemicals
10. Size Classification Of Solids in Water
Dissolved
Colloidal
Suspended or
Non-filterable
10-5 µm
10-4 µm
10-3 µm
10-2 µm
10-1 µm
100 µm
10 µm
100 µm
Dissolved material consists of
molecules and ions that are held
by molecular structure of water.
Colloids are very small
particles that technically
suspended in water but often
exhibit characteristics of
dissolved solids.
Suspended materials consists
of particles larger than
molecular size that are
supported by buoyant and
viscous forces within water.
11. Suspended Solids
Sources
Suspended materials are often natural contaminants in surface water
that come from the errosive action of water flowing over surfaces. Due
to filtration capability of soil SS seldom a constituent of ground water.
Solids suspended in water may consists of inorganic and
organic particles of immiscible liquids.
Inorganic solids such as clay ,slit and other soil
constituents are common in surface waters.
Organic matters such as plant fibers and biological solids
(algae cells,bacteria. etc) are common constituents in
surface waters.
Domestic waste water constrains SS mostly organic in
nature
Industrial use water may result in variety of suspended
impurities of either organic or inorganic nature. Immiscible
liquids such as oils and greases are also constituents of
industrial waste water.
12. Suspended Solids continue…
Impacts
Suspended solids may be objectionable in water for several
reasons:
SS are aesthetically displeasing and provides adsorption
sites for chemical and biological agents.
Suspended organic solids may be biodegradable resulting in
objectionable by-products and also constitutes to BOD
Biological active SS may includes disease causing micro
organisms as well as organisms such as toxin producing
strains.
13. Biochemical Oxygen Demand (BOD)
“The amount of oxygen consumed during microbial
utilization of organics is called the biochemical oxygen
demand.”
Measurement: The BOD is measured by determining the oxygen
consumed from a sample placed in a air tight container and kept
in a controlled environment for a pre-selected period of time.
For a standard test a 300 ml BOD bottle is used and the sample
is incubated at 20 Co for 5 days. Light must be excluded from the
incubator to prevent algal growth that may produce oxygen
inside bottle.
BOD5 = DOi – DOf DOi---- Dissolve Oxygen initial
P DOf----- Dissolve Oxygen final
P ----- Fraction of sample in 300 ml.
14. Chemical Oxygen Demand (COD)
“COD is the amount of oxygen derived from a chemical
oxidizer such as potassium dichromate that is required to
fully convert the organic pollutants onto carbon dioxide ,
water and other oxidized end products.”
Measurement
Measured volume of dichromate is added to a measured
volume of sample then takes place in a concentrated sulfuric
acid environment at a temperature of 148 Co . The mixture boils
for 2 hr only. Sample is again titrated by ferrous ammonium
sulfate for remaining unconverted dichromate.
The method is more accurate than BOD analysis. It provides
a better reading of organic pollutants in the waste water. It
constitutes total oxygen demand that chemically required
however it does not give fraction of biodegradable substances.
15. Alkalinity-PH
Alkalinity: “The neutralization ability of solution against
acidic tendencies is called alkalinity”
Carbonates,bicarbonates,hydroxide etc. contribute to
total alkalinity of a solution.
PH: “ It is the measure of acidity or basisity of a
solution”
PH of a solution is a measure of H+ present.
Higher the concentration of H+ ions lower
the value of PH.
7 143.5 10.51.0
Acidity Basisity
19. WASTE WATER TREATMENT PLANT
WWTP comprises of multiple treatment units for refinery
effluent to bring its pollutants down to the permissible
limits.
Equalization
Physio-chemical Pretreatment
Aerobic Biological Treatment
20. Process Flow Block DIAGRAM
Holding Basin Buffer Tank
CPF
Pre-Selector-1Oxidation Basin
API
TPF
Sludge
Basin
Pre-Selector-2
Secondary
Clarifier-1
Secondary
Clarifier-2
Arabian Sea
21. Equalization
All refinery wastewater streams collect at API separator
where water and oil separates through
gravity difference. The oily water from API separator pit
transferred to equalization tank. This tank has a holding
capacity of 850 m3. Tank is equipped with an aerator, PH
sensor and acid dosing nozzle.
Working Principle: Tank serves as homogenizer for variety
of effluent discharge of the refinery. HCl is supplied to get its
PH down to 8.5 aerator strips out H2S gas from the water.
Thus sulphide level considerably decreased. That is beneficial
for biological process. This homogenized water free from
sulfide fed to Physio-chemical process.
22. BUFFER TANK
FRESH AIR IN
H2S EXHAUST STACK
HCl INJECTION
HOMOGENIZE WATER
TO TPF
MAN HOLE
Buffer Tank Internal Aeration System
26. PHYSIOCHEMICAL PRE-TREATMENT
Physiochemical pretreatment comprises of
chemical and physical separation processes.
PH Control
Coagulation
Flocculation
Flotation
Sludge Separation
All above processes take place in Coiled Pipe Flocculater
(CPF) and Tilted Plate Flocculator (TPF)
27. Coagulation Theory
Coagulation: “It is the neutralization of charged suspensions
present in water.”
Suspended particles in water get charge due to frictional forces due
to this induce charge repulsion force generates that hinders in
suspensions coagulation.
High density charge radical neutralizes this induce charge from
suspensions allowing them to combine to form coagulates.
High density charge radicals are usually trivalent +ve metal ions like
Al3+,Fe3+ etc… These are called coagulant.
28. Coagulation Theory Continue…
Coagulation phenomena consists of following four steps:
Ionic Layer Compression
Adsorption
Charge Neutralization or Destabilization
Flock Formation
29. + -
+ -
+ -
+ -
+ -
+ -
+ -
+ -
+ -
+ -
+ -
+ -
+ -
+ -
+ -
+ -
+ -
+ -
+ -
+ -
+ -
+ -
+ -
+ -
+ -
+ -
+ -
+ -+ -
+ -
+ -
+ -
+ -
+ -
+ -
+ -
+ -
+ -
- +
- +
- +
- +
- +
- +
+
- +
+
++
Electro negative particle
Surface Shear (Bounded
by water molecules)
Stern Layer
Diffuse Layer
Stern potential: Opposite charge surrounding charge particle causes a rapid drop in
potential called as stern potential.
Zeta Potential: Gradual drop in potential between shear surface of boundary water layer
and the point of neutrality in the solution.
Surface Charge on particle
that hinders in coagulation
Stable Colloidal Particle
30. Coagulation Theory Continue…
Ionic Layer Compression
The quantity of charge in the
water surrounding a colloid has
an effect on the decay function of
the electrostatic potential. A high
ionic concentration compresses
the layers predominantly of
counter ions towards the surface
of the colloid. If this layer is
sufficiently compressed then
vander wall forces will be
predominant across the entire
area of influence,so that net force
will be attractive and no more
repulsive energy barrier exits.
Co-ions
Counter ions
Bulksolution
Diffused Layer
Distance From Particle
NumberOfIons
31. Coagulation Theory Continue…
Adsorption and Charge Neutralization
The nature of ions, rather than quantity, is a prime
importance in the theory of adsorption and charge neutralization.
The ionization of aluminum sulfate in water produces sulfate ions
(SO4-2) along with aluminum cat ions Al+3. The aluminum ions
combine with water and forms a variety of aquometallic ions and
hydrogen proton.
Al3+ + H2O AlOH2+ + H+
Al3+ + 2H2O Al(OH)2
+ + 2H+
7Al3+ +17H2O Al7 (OH)4+ + 17H+
Al3+ + 3H2O Al(OH)3 + 3H+
32. Coagulation Theory Continue…
The aqua-metallic ions become part of
the ionic cloud, surrounding the colloid.
Due to high affinity for surfaces these
ions adsorbed onto the colloid surfaces
and neutralize the repulsive charge.
Once the surface charge has been
neutralized ,the repulsive ionic cloud
dissipates and electrostatic charge
disappears. Particles becomes free to
combine/coagulate.
Overdosing of coagulant can restabilize
suspensions. Excessive aqua-metallic
ions are formed and adsorbed they can
reverse the phenomena . Charge on
particles may reverse and regain cloud
of opposite charge.
Distance B/W particlesNet Force
vanderwallVsZ-Potential
Coagulation : Reduction of Net Force
34. Flocculation Theory
Polymer Particle
De-stabilized Particle
Initial Adsorption At Optimum Polymer Dosage
Floc Formation
Secondary Adsorption Of Polymer
De-stabilized Particle Re-stabilized Particle
No contact with vacant sites on
another particle
35. Flocculation Theory Continue…
Initial Adsorption At Excess Polymer Dosage
Stable Particle No Vacant SiteParticle
Polymer
Rupture OF Floc
Floc Fragments
37. Jar Tests For Coagulant Dosage
Coagulation is not yet an exact
science,therefore selection and
optimum dosage of coagulant is
determined experimentally.
These experiments are determined
with a series of jars named as jar
test.
Jar test must be performed for each
type of water that is to be
coagulated. Test results are used
to calculate type and quantity of the
coagulant to be used in the
treatment.
Apparatus
The jar test is performed
using a series of six glass
containers that hold at least 1liter
and are of uniform size and shape.
Stirrer device also required.
38. Jar Tests Continue…
Procedure:
Fill all six jars up to I lit mark. Add coagulant of different
dosage in each 5 jar. 6th Jar placed for reference.
Water is then mixed rapidly for about one min to
ensure complete dispersion of the chemical,then mix
slowly for 15 to 20 min to permit floc formation. The
water is then allowed to settle for approx. 30 min. or at
least clarification occurs. The portion of the settled water
are then removed and tested to determine the remaining
turbidly.
39. Coiled Pipe Flocculator
Working Principle
CPF is a plug flow type piping construction in which all
stages of precipitation takes place sequentially.
Influent water PH is controlled through PLC PH controller to
ensure coagulation process.
Coagulant followed by flocculant are injected to have
precipitation of suspensions and flocculation.
Intensive and instantaneous mixing of the PH correcting
chemicals ,coagulant and flocculant chemicals is achieved
by the turbulence created inside CPF.
Flocculated suspensions mix with air saturated water to get
flotation effect caused by gravity difference
The dosing rate of coagulant and flocculant are adjusted
manually according to the feed rate.
41. Coiled Pipe Flocculater CPF
CPF
Coiled pipe floculator
equipped with injection points
for PH regulation Alum and PE
solutions injections for
coagulation and flocculation.
CPF is a variable area pipes
sections with different lengths to
ensure necessary residence time
for completion of the process.
PH
DAF
Air Saturated
water injections
Alum
PE
42. Tilted Plate Flotator (TPF)
In the TPF the destabilized and flocculated oil emulsions and colloid
suspensions are removed by means of the Dissolved Air Flotation
process.
TPF based on the principle that by attaching tiny air bubbles with the
flocs provide intense flotation effect due to gravity difference.
The sludge containing the air bubbles and contaminants floats readily on
the liquid surface. From where it is removed by means of pneumatic
driven skimmer.
To dissolve the required amount of air ,a definite amount of air is mixed
with recycle water and is passed through a pump ,specially designed for
this duty, then release pressure into DAF. Here water saturates with air
and transferred into tiny bubbles 30 to 50 microns.
Air saturated water is entered into CPF at 6 injections point partially. In
this way maximum contact of air bubbles with flocs occur.
TPF is equipped with fiber tilted plates at angle of 45o. Water enters TPF
through inlet perforated nozzle. Nozzle drives centrifugally and sludge
floats outwards to the surface.
Tilted plates provided maximum contact between waters of high density
(relatively pure) and of light water containing air-lifted sludge.
43. TPF Side View: Coagulated
water enters into TPF through CPF
line ending with a distributor
Tilted Plates: Tilted Plates placed
at 45o angle with the axis of TPF basin.
Water with lesser gravity flows
outwards while of higher gravity moves
downwards provides intimate contact.
44. Tilted Plate Flotator (TPF)
Sludge At Surface
Clean Water Flows out
Perforated pipe
Tilted Plates
Air Injection
DAF
Re-circulation Pump 9 m3/hr,6 kg/cm2
45. Tilted Plate Flotator (TPF)
The Skimmer
Sludge floating at TPF is removed
through skimmer, top mounted on
TPF.
Skimmer is equipped with
horizontal scrapper with air drive
pistons.
Skimmer is operated through auto
PLC sequence. Play time adjusted
with reference to sludge
accumulation rate
48. Biological Treatment
Biological Treatment is applied for digestion of biodegradable
impurities. Biodegradable matter is responsible for BOD, this parameter
is worth controlling to meet standards and to save marine life.
Biological water treatment is achieved by naturally occurring species ;
microorganisms. In such a treatment environment is provided for
culture growth. Micro-organisms utilizes impurity as their food and
oxidize it producing water and carbon dioxide.
Biological Treatment comprises of the following units.
Preselctors
Oxidation Basin
Secondary Clarifiers
49. Control Parameters
MLSS: Mix liquor suspended solids
Suspended solids present in water temporarily mix with
help of mechanical means(agitation) are termed as
MLSS.
MLSS is determined by weight analysis in lab through
filtration and drying procedure.
MLSS in biological treatment is an important parameter
that provides the measurement of combine sludge in
oxidation basin. (Total suspensions)
3500 ppm of MLSS level is maintained in oxidation
basin through continuous recycling of activated sludge
Excessive MLSS is expelled into sludge thickener
compartment through activated sludge recycle stream.
Biological Treatment
50. Biological Treatment
MLVSS: Mix liquor volatile suspended solids
The actual living organism in MLSS are reported as MLVSS.
After MLSS analysis the dried sludge sample is heated in
furnace at temperature of 550 Co . The volatile species (organic
part) removes only ash remains. The quantitative difference
between MLSS and this remainder is claimed as MLVSS.
MLVSS is maintained at level of 3500 ppm corresponding MLSS
level.
MLSS and MLVSS can never be equal theoretically or practically
yet a close agreement is expected to assume quality of
activated sludge.
Sludge Volume
Sludge volume in oxidation basin (ml/lit) is measured
One liter sample from oxidation basin is kept quiescent for
30 min the level settled down is taken from graduated scale.
Oxidation basin SV is maintained at 450 ml/lit
51. Biological Treatment
Sludge Volume Index: SVI
It is also an important parameter to understand quality of
sludge.
SVI is maintained 80-120 ml/gm
SVI is proportional to the MLSS and SV by this formula
SVI =
SV * 1000
MLSS
(ml/gm)
Sulfide:
Sulfide concentration is kept lesser than 0.1 ppm
whether CPF outlet is 100 ppm.
Sulfide slight higher concentration can destroy
microorganism.
Ferric chloride is added in preselector to oxidize
sulfide into sulfates.
52. Biological Treatment
Preselector (Bioreactor)
The first step of the aerobic biologic effluent treatment takes place in the preselector.
Preselector consists of 2 separate concrete tanks ,each equipped with a mixer device.
First preselector receive activated sludge recycle and effluent water from TPF. Water from
TPF considered to be free from suspensions only impurity present is dissolve substances.
The activated sludge adsorbs at a quite high rate the dissolved organic
contaminants at their cell walls through both chemical and biochemical bonds.
At the same time the microbes through variety of chemical bonds attach
themselves to oily and suspended particles that have passed the dissolved air
flocculation
The microbes starts producing exo-enzymes which enables them to hydrolyze and
decompose the absorbed organic compounds.
A preferential selection of microbes grows ,as only the microbes which are best
equipped for immediate adsorption of the organic contaminants ,can only well
survive. Types of microbes that adsorb organics at slower rate during the pre-
selection phase out due to starvation(food shortage).
53. Biological Treatment
The types best equipped are those with a distinct polysaccharide layer around
their cell wall; the layer functions as the adsorbent for organic contaminants.
The same layer also ensure at a later stage in the settling basin,the flocculation
of microbes,through the process they become separable from water due to
gravity.
The environment in the pre-selector is definitely adverse for hosts of
filamentous sludge species which leads to sludge bulking.
The phenomenon of filamentous sludge leads to bulking.
Sludge bulking decreases flocculation ability and tends to float over water
surface.
The phenomenon of pre-selection is most useful tool to avoid sludge bulking as
it directly discourages the generation of filamentous sludge.
In pre-selection the food is immediately adsorbed by activated sludge by itself.
There is nothing left for slower growing other species ( like filamentous
bacteria). Therefore in pre-selection process these species disappear.
Preselector (Bioreactor)
Sludge Bulking
54. Biological Treatment
The internal configuration of the pre-selector has been designed to minimize
the hydraulic short circuiting and back mixing in reactors.
Total retention time in both the pre-selectors is 25 minutes, after that water
runs to the oxidation basin.
First preselector receives recycle sludge form clarifiers. Phosphoric acid is
injected for microbes integration. Ferric chloride is injected to oxidize
sulfides to sulfates
Both the pre-selectors are equipped with submersible motor driven mixers.
These mixers are designed for entire homogeneity of water and activated
sludge.
Submersible Mixer
Preselector (Bioreactor)
59. Element
%age
Dry- Wt.
Source Function
Carbon 50
Organic compounds
or CO2
Main constituent of cellular material
Oxygen
20
H2o , organic
compounds,CO2, N2
Constituent of cell material and cell water ; O2 is
electron accepter in aerobic respiration
Nitrogen 14
NH3,NO3,Organic
compounds, N2
Constituent of amino acids, nucleic acids,
nucleotides and coenzymes
Hydrogen 8
H2O, Organic
compounds, H2
Main constituent of organic compounds and cell
water
Phosphorus 3
Inorganic
phosphates (PO4)
Constituent of nucleic acids, nucleotides,
phospholipids
Sulfur 1
SO4, H2S, S , organic
sulfur compounds
Constituent of cysteine, several co- enzymes
Potassium
1
Potassium salts
Main cellular cation and cofactor for certain
enzymes
Magnesium 0.5 Magnesium salts
Inorganic cellular cation, cofactor for certain
enzymatic reactions
Calcium 0.5 Calcium salts
Inorganic cellular cation, cofactor for certain
enzymes and a component of endospores
Component of cytochromes and certain nonheme
Major Elements, Sources and function in Bacteria Cell
60. Microbes needs dissolve oxygen in water to intake for digestion, this
phenomenon is achieved in oxidation basin
Oxidation basin equipped with aerators, internal baffle outlet mesh and
contained of volume 240 m3 that provides a hydraulic detention time of
70 hrs.
Water overflows form second preselector to oxidation basin.
High detention time ,70 hr, enables microbes to digest and metabolize
adsorbed substrates.
Microbes derive their energy from oxidation digestion , a part of which
is utilized in re-synthesis of new cell tissue. This synthesis leads to an
increase of total cell population. Reported in activated sludge growth.
Remaining part of energy is expelled into surroundings.
A sufficient amount of dissolved oxygen is provided by means of two
submersible ejectors type aerators.
Continuous aeration support microbes to digest their food and to
promote new cell growth.
PLC Control loop implies to maintains desirable dissolve oxygen
concentration
Biological Treatment
Oxidation Basin
63. Biological Treatment
Secondary Clarifiers
Two parallel secondary clarifiers are employed for the segregation of treated
effluent from activated sludge.
Imhof type clarifiers are based on the principle of gravity settling by
affording ample time.
Clarifiers bottom structure is steep like structure with an angle of 60o
The design overflow of each clarifier is 0.5 m/hr, that provides stream like
quiescent flow helps in gravity settling of microbes flocks ( Activated
Sludge).
First tranquilizing zone helps in re-coaglomeration of activated sludge
particles through their ability to auto flocculate. That ‘s due to
polysaccharide layer around the microbes cell wall.
Surface load of suspended solids (SS) is 0.4 Kg/(m2/h)
The flow rate of both the clarifiers is balanced by a set of outlet weirs. V-
notch is provided on the either side to measure over flow rate from each
clarifier.
The clarified water is discharged directly into the clarified water basin.
64. Biological Treatment
Secondary Clarifiers
Arabian Sea
Knock Out Pit
Discharge Pit
Preselector-I
20m3/hr * Each
Sludge -
Thickener
Volume = 81.5 m3 * Each
Retention Time = 4 hr-37 min
Liquid Load = 70 m3/hr
65. Biological Treatment
Clarifiers Outflow Weir
Secondary Clarifiers discharge though outlet
weirs. The final treated water to sea.
Weir are mounted by sliding bolts,by which
flow can be balanced between both
compartments of the clarifier.
Clean Water flow is spectacular over the
weirs any SS passing through water is quite
visible.
V-notch is attached at out-way of both
compartments. Flow rate can be measured
through direct scale reading on V-notch.
72. Parameter Sample point Daily Twice weekly Weekly Target value
BOD CPF in X 120 mg/l--O2
TPF-out X 102 mg/l--O2
Scond. Clarifier out X <5 mg/l--O2
COD CPF-in X 450 mg/l--O2
TPF Out X 330 mg/l--O2
Second. Clarifier out X <50 mg/l--O2
Nkj CPF-in X 60 mg/l
Second. Clarifier out X 15 mg/l
NH4+ CPF-in X 25-50 mg/l
Second. Clarifier out X 15 mg/l
NO3 CPF-in X 5 mg/l
Second. Clarifier out X 10 mg/l
Ptol CPF-in X 0 mg/l
TPF out X 0 mg/l
Secon. Clarifiers out X 1 mg/l
MLSS Oxidation Basin X 3500 mg/l
MLVSS Oxidation Basin X 3500 mg/l
Control Parameters Their Targets and Testing Frequency
73. Control Parameters Their Targets and Testing Frequency
TDS CPF- in X 2000-3200 mg/l
TPF- out X 2000-3200 mg/l
Secon. Clarifiers out X 40-120 mg/l
TSS CPF- in 40-120
TSS Secon. Clarifiers out X <30 mg/l
TSS TPF- out X 5-10 mg/l
SV Oxidation Basin X 450 mg/l
SVI Oxidation Basin X 80-120 mg/l
DO Oxidation Basin X 1-2 mg/l
PH CPF-in X 8.5
PH TPF- out X 7-7.3
PH Oxidation Basin X 7-8.5
PH Second. Clarifier out X 7-8.5
Oil & grease CPF- in X 40 mg/l
Second. Clarifier out X 0.1 mg/l
Temperature CPF-in 30-35o
C
Second. Clarifier out 30-35o
C
Phenolic CPF- in X 3-5 mg/l
TPF- out X 2 mg/l
Sulphide CPF-in X 100 mg/l
TPF- out X 30 mg/l
Second. Clarifier out X 0.1 mg/l