This document provides information about jigs and fixtures from a manufacturing processes lecture. It defines jigs and fixtures, outlines their differences and uses. It describes locating principles like the 3-2-1 principle and different locating devices like pins, vee blocks, and diamond pins. It also discusses clamping methods like screw clamps, cam clamps, and quick acting nuts. Finally, it provides design principles for drilling jigs and describes drilling bushes.
Fundamentals of Metal cutting and Machining Processes
MACHINING OPERATIONS AND MACHINING TOOLS
Turning and Related Operations
Drilling and Related Operations
Milling
Machining Centers and Turning Centers
Other Machining Operations
High Speed Machining
What does clamping mean in context of jigs and fixtures?
Principles of Clamping
Different types of Clamping Devices, their advantaged and disadvantages
education is a key for everything so the objective of this slide is to share knowledge to the glob in my area of specialization.
This lecture note is basically designed for mechanical Engineering Manufacturing stream students and Instructors.
Fundamentals of Metal cutting and Machining Processes
MACHINING OPERATIONS AND MACHINING TOOLS
Turning and Related Operations
Drilling and Related Operations
Milling
Machining Centers and Turning Centers
Other Machining Operations
High Speed Machining
What does clamping mean in context of jigs and fixtures?
Principles of Clamping
Different types of Clamping Devices, their advantaged and disadvantages
education is a key for everything so the objective of this slide is to share knowledge to the glob in my area of specialization.
This lecture note is basically designed for mechanical Engineering Manufacturing stream students and Instructors.
igs and fixtures are specialised tools used in manufacturing to secure workpi...yhchauhan
igs and fixtures are specialised tools used in manufacturing to secure workpieces and guide cutting or shaping tools, ensuring precision and repeatability in production processes.
DESIGN AND DEVELOPMENT OF MACHINING FIXTURE FOR BD65 FINAL DRIVE CASE ON HORI...IAEME Publication
A machining fixture is a device used to hold or support work in the manufacturing
industry. By using the specifications of the horizontal machining center, we designed
and analyzed the 3D model of the fixture in the software. For the final drive case, this
machining fixture on LH & RH is used for Bharath dozers 65 ton capacity. This
horizontal machining center will increase production rates, reduce demand for labor,
save time. This machine will be performed after production hours, after operations
such as drilling, boring, tapping, reaming, threading. Using a fixture improves the
economy of production by enabling smooth operation and rapid transition from part
to part, reducing the skilled labor requirement to simplify set-up and use of fixtures,
and increasing compliance across a production run
DESIGN OF FIXTURE OF CONNECTING ROD FOR BORING OPERATIONijsrd.com
Connecting rod is very important part of engine. It should be accurately machined with the acceptable tolerance. Also the fluctuations of dimensions in work-piece to work piece should be minimum so that it will be easier to assemble in engine. But it has been observed that the required dimensions for the bolt diameter and smaller end diameter for the connecting rod are not continuously achievable by using the existing fixture. The diameters required of the bolts and the smaller end of the said connecting rod are 10±0.05 mm and 24±0.01 mm respectively The aim of this project is to design and development of a new fixture for machining (Boring) operation using designing software's i.e. Pro E and analysis using ANSYS ,which can eliminate the said problems. And the production rate will also increase up to 15% which is quite objective. So for that, a new hydraulic fixture is designed and observed that dimensional accuracy, increased production rate up to 15% and more output per day with boring operation. Which defines process is satisfactory enough and validates the project.
Model Attribute Check Company Auto PropertyCeline George
In Odoo, the multi-company feature allows you to manage multiple companies within a single Odoo database instance. Each company can have its own configurations while still sharing common resources such as products, customers, and suppliers.
Safalta Digital marketing institute in Noida, provide complete applications that encompass a huge range of virtual advertising and marketing additives, which includes search engine optimization, virtual communication advertising, pay-per-click on marketing, content material advertising, internet analytics, and greater. These university courses are designed for students who possess a comprehensive understanding of virtual marketing strategies and attributes.Safalta Digital Marketing Institute in Noida is a first choice for young individuals or students who are looking to start their careers in the field of digital advertising. The institute gives specialized courses designed and certification.
for beginners, providing thorough training in areas such as SEO, digital communication marketing, and PPC training in Noida. After finishing the program, students receive the certifications recognised by top different universitie, setting a strong foundation for a successful career in digital marketing.
2024.06.01 Introducing a competency framework for languag learning materials ...Sandy Millin
http://sandymillin.wordpress.com/iateflwebinar2024
Published classroom materials form the basis of syllabuses, drive teacher professional development, and have a potentially huge influence on learners, teachers and education systems. All teachers also create their own materials, whether a few sentences on a blackboard, a highly-structured fully-realised online course, or anything in between. Despite this, the knowledge and skills needed to create effective language learning materials are rarely part of teacher training, and are mostly learnt by trial and error.
Knowledge and skills frameworks, generally called competency frameworks, for ELT teachers, trainers and managers have existed for a few years now. However, until I created one for my MA dissertation, there wasn’t one drawing together what we need to know and do to be able to effectively produce language learning materials.
This webinar will introduce you to my framework, highlighting the key competencies I identified from my research. It will also show how anybody involved in language teaching (any language, not just English!), teacher training, managing schools or developing language learning materials can benefit from using the framework.
Unit 8 - Information and Communication Technology (Paper I).pdfThiyagu K
This slides describes the basic concepts of ICT, basics of Email, Emerging Technology and Digital Initiatives in Education. This presentations aligns with the UGC Paper I syllabus.
Exploiting Artificial Intelligence for Empowering Researchers and Faculty, In...Dr. Vinod Kumar Kanvaria
Exploiting Artificial Intelligence for Empowering Researchers and Faculty,
International FDP on Fundamentals of Research in Social Sciences
at Integral University, Lucknow, 06.06.2024
By Dr. Vinod Kumar Kanvaria
The French Revolution, which began in 1789, was a period of radical social and political upheaval in France. It marked the decline of absolute monarchies, the rise of secular and democratic republics, and the eventual rise of Napoleon Bonaparte. This revolutionary period is crucial in understanding the transition from feudalism to modernity in Europe.
For more information, visit-www.vavaclasses.com
June 3, 2024 Anti-Semitism Letter Sent to MIT President Kornbluth and MIT Cor...Levi Shapiro
Letter from the Congress of the United States regarding Anti-Semitism sent June 3rd to MIT President Sally Kornbluth, MIT Corp Chair, Mark Gorenberg
Dear Dr. Kornbluth and Mr. Gorenberg,
The US House of Representatives is deeply concerned by ongoing and pervasive acts of antisemitic
harassment and intimidation at the Massachusetts Institute of Technology (MIT). Failing to act decisively to ensure a safe learning environment for all students would be a grave dereliction of your responsibilities as President of MIT and Chair of the MIT Corporation.
This Congress will not stand idly by and allow an environment hostile to Jewish students to persist. The House believes that your institution is in violation of Title VI of the Civil Rights Act, and the inability or
unwillingness to rectify this violation through action requires accountability.
Postsecondary education is a unique opportunity for students to learn and have their ideas and beliefs challenged. However, universities receiving hundreds of millions of federal funds annually have denied
students that opportunity and have been hijacked to become venues for the promotion of terrorism, antisemitic harassment and intimidation, unlawful encampments, and in some cases, assaults and riots.
The House of Representatives will not countenance the use of federal funds to indoctrinate students into hateful, antisemitic, anti-American supporters of terrorism. Investigations into campus antisemitism by the Committee on Education and the Workforce and the Committee on Ways and Means have been expanded into a Congress-wide probe across all relevant jurisdictions to address this national crisis. The undersigned Committees will conduct oversight into the use of federal funds at MIT and its learning environment under authorities granted to each Committee.
• The Committee on Education and the Workforce has been investigating your institution since December 7, 2023. The Committee has broad jurisdiction over postsecondary education, including its compliance with Title VI of the Civil Rights Act, campus safety concerns over disruptions to the learning environment, and the awarding of federal student aid under the Higher Education Act.
• The Committee on Oversight and Accountability is investigating the sources of funding and other support flowing to groups espousing pro-Hamas propaganda and engaged in antisemitic harassment and intimidation of students. The Committee on Oversight and Accountability is the principal oversight committee of the US House of Representatives and has broad authority to investigate “any matter” at “any time” under House Rule X.
• The Committee on Ways and Means has been investigating several universities since November 15, 2023, when the Committee held a hearing entitled From Ivory Towers to Dark Corners: Investigating the Nexus Between Antisemitism, Tax-Exempt Universities, and Terror Financing. The Committee followed the hearing with letters to those institutions on January 10, 202
Macroeconomics- Movie Location
This will be used as part of your Personal Professional Portfolio once graded.
Objective:
Prepare a presentation or a paper using research, basic comparative analysis, data organization and application of economic information. You will make an informed assessment of an economic climate outside of the United States to accomplish an entertainment industry objective.
Acetabularia Information For Class 9 .docxvaibhavrinwa19
Acetabularia acetabulum is a single-celled green alga that in its vegetative state is morphologically differentiated into a basal rhizoid and an axially elongated stalk, which bears whorls of branching hairs. The single diploid nucleus resides in the rhizoid.
1. Program: B Tech(Mechanical)
Class: SE
Course: Manufacturing Process-2
Unit: Jigs and fixture
Lecture 01: Design principles
School of Engineering and Technology
2. 2
www.sandipuniversity.edu.in
1. Prof Arif K Mansuri
2. Years of Experience:-24
3. Domain Expertise:-Advance Production Systems
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
4. 4
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
Definitions
Jig: A device that holds the work and
locates the path of the tool
Fixture: A device fixed to the worktable of a
machine and locates the work in an exact
position relative to the cutting tool.
5. 5
www.sandipuniversity.edu.in
DIFFERENCES
JIG FIXTURE
Definition Locates and Holds
the work and guides
the cutting tool in true
position of the work
Only Holds & Positions
the work, but doesn’t
guide the work
Elements Work Locating
elements, Tool
Guiding elements &
Work Clamping
elements
Work Locating elements,
Tool setting elements &
Work Clamping
elements
Construction Light Heavy
Applications Drilling, reaming ,
Tapping,
Counterboring,
Countersinking
Drill bushes used for
tool guiding
Milling, Turning,
Grinding, Broaching etc.,
Special
features
Feeler gauges, setting
blocks to adjust position
of tool in relation to work
6. 6
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
Uses of J & F in Manufacturing Industries
1) To reduce production cost
2) To increase production rate
3) To ensure high accuracy in part manufacture
4) To enable heavy and complicated complex shaped parts to be machined by being held rigidly to a
machine
5) To provide interchangeability
6) Reduce quality control expenses
7) Less skilled labour & save labour costs
8) Improve work safety Jigs & Fixtures are special purpose tools which are used to facilitate production
in mass scale
9) They eliminate the necessity of a special set up for each individual part
10) Once a Jig or fixture is properly set-up any number of same parts may be readily produced without
additional set-up.
8. 8
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
Fixture
Jigs & Fixtures are special purpose tools which are used to
facilitate production in mass scale
A fixture only locates and
hold the work piece with
reference point for setting
a work piece.
10. 10
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
3-2-1 Locating Principle
⚫A workpiece, just like any free solid body, has
twelve (12) degrees of freedom
⚫To confine the workpiece accurately and
positively in another fixed body (Jig or
fixture), the movement of the workpiece in
any of the twelve degrees of freedom must
be restricted.
11. 11
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
3-2-1 Locating Principle
⚫A workpiece, just like any free solid body, has
twelve (12) degrees of freedom
⚫To confine the workpiece accurately and
positively in another fixed body (Jig or
fixture), the movement of the workpiece in
any of the twelve degrees of freedom must
be restricted.
12. 12
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
3-2-1 Locating Principle
• The workpiece is resting on three pins A, B
and C which are inserted in the base of
the fixed body. The workpiece cannot rotate
about the axes XX and YY and also it
cannot move downward. In this way the
five degrees of freedom 1, 2, 3, and 5
have been arrested.
• Two more pins D and E are inserted in the
fixed body, in a plane perpendicular to the
plane containing the pins A. B and
C. Now the workpiece cannot rotate about
the Z-axis and also it cannot move towards
the left. Hence, the addition of pins D and E
restrict three more degrees of freedom,
namely 6, 7 and 8.
• Another pin F in the second vertical face of the
fixed body, arrests degree of freedom 9.
14. 14
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
Locating Devices
-Pins of various designsand made of hardened steel are the most
common locating devices used to locate a workpiece in a jig or fixture
-The locating diameter of the pin is made larger than the shank
to prevent it from being forced into the jig or fixture body due to
the weight of the workpiece or the cutting forces.
15. 15
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
⚫Cylindrical Locators: Used for locating components having drilled
holes.
⚫The cylindrical component to be located is gripped by a cylindrical
locator fitted to the jig’s body and inserted in the drilled hole of the
component.
Locating Devices
16. 16
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
Locating Devices
⚫Conical Locator : Used for locating the workpieces having cylindrical
hole.
⚫It is superior as it has a capacity to accommodate a slight variation in the
hole diameter of the component without affecting the accuracy of
location.
17. 17
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
⚫Jack pin locator: Used to support rough, un-machined surface
⚫Height can be adjusted
⚫A suitable method to accommodate the components
whichare rough like castings.
Locating Devices
18. 18
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
Locating Devices
⚫Vee Locators: Quick and effective method of locating the
workpiece.
⚫Used for locating the circular and semi-circular type of workpieces.
19. 19
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
Locating Devices
⚫Vee Locators: Quick and effective method of locating the
workpiece.
⚫Used for locating the circular and semi-circular type of workpieces.
20. 20
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
Locating Devices
⚫Vee Locators: Quick and effective method of locating the
workpiece.
⚫Used for locating the circular and semi-circular type of workpieces.
21. 21
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
Locating Devices
• Adjustable ‘V’Locator: Components like raw castings / forgings are required to be sometimes
located
on their as cast/as forged circular part profiles.
•An adjustable or sliding V locator is used which accommodate the size variation at the profile.
22. 22
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
Locating Devices
Support Pins
• With these pins (also known as rest pins),
workpieces with flat surfaces can be
supported at convenient points.
23. 23
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
Locating Devices
Jack Pins
• Jack pins/spring pins are also
used to locate the workpieces
whose dimensions are subject
to variation,
• The pin is allowed to come up under spring pressure or conversely is pressed
down by the workpiece. When the location of the workpiece is secured. the
pin is locked in this position by means of the locking screw
24. 24
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
Locating Devices
Diamond Pin Locator
⚫Diamond pinsareoften used for radial location .
⚫One cylindrical locator (Pin A) arrests five degrees of freedom, second
cylindrical locator at the position B will arrest the sixth degree of
freedom.
⚫If the two holes are identical in size then any pin can be made the
principal locator. However, if one of the holes is larger then the principal
locator will be placed in the larger hole.
⚫The second locator is made slightly smaller than the hole and relieved
from both sides to take care of the variation in the X direction. The
cylindrical surfaces will locate the part in theYdirection.
26. 26
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
Locating Devices
Diamond Pin Locator
⚫Diamond pinsareoften used for radial location .
⚫One cylindrical locator (Pin A) arrests five degrees of freedom, second
cylindrical locator at the position B will arrest thesixth degree of freedom.
⚫If the two holes are identical in size then any pin can be made the principal
locator. However, if one of the holes is larger then the principal locator will
be placed in the larger hole.
⚫The second locator is made slightly smaller than the hole and relieved
from both sides to take care of the variation in the X direction. The
cylindrical surfaces will locate the part in theYdirection.
28. 28
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
Locating Devices
Diamond Pin Locator
Diamond pin location is used in a fixture because
(a) It does notwearout
(b)It takes care of any variation in centre distance
between two holes
(c) It is easy toclamp the parton diamond pins
(d) It is easy to manufacture
IES – 1998, 1999
29. 29
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
Clamping
⚫To restrain the workpiece completely a
clamping device is required.
⚫Holds the workpiece securely in a jig or
fixture against the forces applied over it
during on operation.
⚫Device should be incorporated into the
fixture, proper clamp in a fixture directly
influence the accuracy and quality of the
work doneand productioncycle time.
30. 30
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
Principles of Clamping
1) The clamping pressure applied against the workpiece must counteract the
tool forces
2) The clamping pressure should not be directed towards the cutting
operation. Wherever possible it should be directed parallel to it.
3) The clamping pressure must not damage/deform the work surface.
4) Clamps should be arranged directly above the points supporting the work,
otherwise distortion of work may occur.
5) Clamping pressure should be directed towards the points of support, else
the work will tend to rise from support
6) Clamping should be simple, effective and foolproof.
7) Fibre pads should be riveted to clamp faces to avoid damage to fragile
workpieces
31. 31
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
Clamping
•It blocks one side of the jig / fixture
which makes loading and unloading
difficult.
•Due to direct contact with the workpiece,
it tries to rotate the
workpiece.
Simple Screw Clamp
32. 32
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
Clamping
Swinging Screw Clamp
-During loading and unloading the
swinging clamp is switch to off
position, so it will not affect the
loading and unloading of the
component.
-Due care is taken at the fitment of
fulcrum pin to see that the pin itself
dose not come out while clamping.
33. 33
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
Clamping
Strap Clamp
⚫Based upon the lever principles to amplify the
clamping force required.
⚫By tightening the stud the clamping force is
transferred to the part.
⚫Heel pin is the fulcrum about which the lever acts
while the clamping force is applied at the stud by
tightening thescrew.
⚫The actual amplification of the applied force
depends upon the distance between the stud and
the heel pin (B), and that between the stud and
thepart (A).
34. 34
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
Clamping
Cam Clamps
⚫ Provide clamping force because of the contour of the cam
surface that comes into contact with the plate used for the
clamping.
⚫ Plate is pushed down by the cam against the spring pressure to
hold the part in place.
⚫ Cam clamps arequick in operation.
⚫ Cam clamps are of three types, eccentric cam, flat spiral cam
and cylindrical cam.
⚫ The design shown in Fig. is flat spiral and is the most
commonlyused clamp.
⚫ A cam clamp used forquick and easy clamping a part
36. 36
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
Clamping
Cam Clamps
⚫ Provide clamping force because of the contour of the cam
surface that comes into contact with the plate used for the
clamping.
⚫ Plate is pushed down by the cam against the spring pressure to
hold the part in place.
⚫ Cam clamps arequick in operation.
⚫ Cam clamps are of three types, eccentric cam, flat spiral cam
and cylindrical cam.
⚫ The design shown in Fig. is flat spiral and is the most
commonlyused clamp.
⚫ A cam clamp used forquick and easy clamping a part
37. 37
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
Clamping
C-Clamps
This is quick clamping device which reduces
time required for clamping and unclamping.
To unload the work piece, the locking nut is
unscrewed by giving it about one turn and
this releases the c- clamp. When the clamp is
removed or swing away the work piece can
freely pass over the nut. Reverse procedure
is adopted for loading the work piece.
38. 38
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
Clamping
Quick Acting Nut
• The threads of the nut are not continuous but are interrupted.
• The length of the nut is about 2 to 3 times the thread diameter.
• The diameter of the clearance ‘D‘ is slightly bigger than the outside
diameter of the thread and the axis of the hole is inclined at angle (3° to
7°) to the axis of nut.
• When the nut is assembled over the male thread.
• It is inclined to the axis of the clearance hole.
• When the nut engages the male thread, it is dropped on to the screw threads
and is then tightly locked by giving it about half a tum.
39. 39
www.sandipuniversity.edu.in
SCHOOL OF ENGINEERING AND TECHNOLOGY
Clamping
Quick Acting Clamp Cam operated
• These clamps find
application and are fast
broad
and
positive in action. These should
not be used where vibrations are
present or whore the dimensions
of the workpiece vary. e.g.. sand
castings.
ProductionTechnology Prof.
40. 40
www.sandipuniversity.edu.in
Design Principles for Drilling Jigs:
1. A drilling jig should be of light construction consistent with adequate
rigidity to facilitate its handling because it has to be handled
frequently during the operation.
2. A drilling jig which is not normally clamped to the machine table
should be provided with four feet.
3. The stability of a drilling jig should be as good as possible since it is
not usual to clamp it to the machine table and to ensure this, the feet
or base of the jig should extend outside the holes to be drilled.
4. Drill bushings should be fitted in fixed portion of the jig.
Drilling Jigs
42. 42
www.sandipuniversity.edu.in
The stiffness of the cutting tool may be insufficient to perform certain machining operations. To
eliminate the elastic spring back in machining and to locate the tool relative to the work, use is made
of guiding parts, such as, jig bushings/templates. These must be precise, wear resistant and
changeable.
1. Press Fit bushings
2. Renewable bushes.
3. Slip Bushes
4. Screw bush.
5. Liner Bushings
1. Press Fit bushings
• These bushings are used when little importance is put on accuracy
or finish, and the tool used is a twist drill.
• Installed directly in the jig body
When the jig plate into which it is installed is thin, the flanged or headed portion increasing the length of the
bush which provides longer guiding portion to the bush than would otherwise be available. The flange or head
also acts as a stop for the tool.
Drilling Bushes
43. 43
www.sandipuniversity.edu.in
Drilling Bushes
2. Renewable bushes
• When bushes require periodic
replacement (due to the wear of
the inside diameter of the bush,
in case of continuous or large
batch production), the
replacement is simplified by
using a renewable bush.
• These are of the flanged type and
are sliding fit into the liner bush,
which is installed (press fitted in
the jig plate).
• Must be prevented rotating or
lifting with drill by using
retaining screw.
3. Slip Renewable bushes
• Slip bushes are used when more than one bushings are to be interchanged
in a given size of the liner. ProductionTechnology Prof.Naman M.Dave
44. 44
www.sandipuniversity.edu.in
4. Screw bushes
The screwing of the bush into the jig body not only holds the bush in place,
but it also makes the bush adjustable.
5. Linear bushes
These
known
bushings,
as
also
'master
bushings' are permanently
fixed into the jig body.
These act as guides for
renewable type bushings.
ProductionTechnology Prof.Naman M.Dave
Drilling Bushes
45. 45
www.sandipuniversity.edu.in
Drilling Jigs: Types
1. Template Jig
2. Plate Type Jig
3. Open Type Jig
4. Swinging Leaf Jig
5. Box Type Jig
6. Channel Type Jig
7. Sandwich Jig
8. Angular Jig
9. Angle Plate Jig
10.Pot Jig
11.Turn-over Jig
12.Diameter Jig
13.Multi-station Jig
14.Standard Jig
15.Universal Jig
• Simplest type of drilling jig.
• Simply a plate made to the shape and size of the
workpiece with the required number of holes made in
it accurately.
• Placed on the workpiece and the holes in the
workpiece will be made by the drill which will be
guided through the holes in the template.
• The plate should be hardened to avoid its frequent
replacement. This type of jig is suitable if only a few
parts are to be made.
46. 46
www.sandipuniversity.edu.in
Plate type Jig
• This is an improvement over the template type of jig. In place of simple holes,
drill bushes are provided in the plate to guide the drill. The workpiece can be
clamped to the plate and the holes drilled
Open type Jig
47. 47
www.sandipuniversity.edu.in
Swinging leaf Jig
• A sort of open type jig in
which the top plate is
arranged to swing about a
fulcrum point so that it
completely clears the jig
for easy loading and
unloading of the
workpiece.
• The drill bushes are fitted
into the plate which is also
known as leaf, latch or lid. Video
49. 49
www.sandipuniversity.edu.in
Box type Jig
• When holes are to be drilled
in more than one plane of a
workpiece, the jig has to be
provided with equivalent
number of bush plates. For
positioning the jig on the
machine table, feet have to be
provided opposite each
drilling bush plate.
• One side of the jig will be
provided with a swinging leaf
for loading and unloading the
workpiece. Such a jig would
take the form of a box.
• When, one or more sides of
the box jig are kept open for
loading/unloading, it is
known as Tumble type and
Trunnion type box jig.
55. 55
www.sandipuniversity.edu.in
Principle of Fool Proofing
While locating a workpiece within a locating system, it is
sometimes the work-piece does not have a unique single orientation.
To locate workpiece at its predefined position fool proofing
arrangement is made in the jigs or fixtures.
Examples :-
62. 62
www.sandipuniversity.edu.in
GATE - 2005
When 3-2-1 principle is used to support and locate a
three dimensional work-piece during machining,
of degrees of freedom that are
the number
restricted is
(a) 7
(b) 8
(c) 9
(d) 10
63. 63
www.sandipuniversity.edu.in
GATE-2013
In the 3-2-1 principleof fixture design, 3 refers to the
numberof
(a) Clampsequired
(b) Locators on the primarydatum face
(c) Degreesof freedomof theworkpiece
(d) Operationscarried out on the primarydatum face
64. 64
www.sandipuniversity.edu.in
IES 2011
In the 3-2-1 principleof fixture 3 refers to numberof
(a) Setups possible
(b) Clamps required
(c) Positions on primary face
(d) Locating positions
65. 65
www.sandipuniversity.edu.in
GATE - 1999
Choosethecorrectstatement:
(a)A fixture is used toguide the tool as well as to locate
and clamp theworkpiece
(b)A Jig is used toguide the tool as well as to locateand
clamp theworkpiece
(c)Jigs arc used on CNC machines to locateand clamp
theworkpieceand also toguide the tool
(d) Noarrangement toguide the tool is provided in a jig.