This document describes a study on the tribological properties of an aluminum-based composite material for potential use as an automotive brake material. The researchers developed an aluminum-titanium carbide composite using stir casting and tested it using a pin-on-disc tribometer. Experiments were designed using the Taguchi method to evaluate the effects of load, sliding speed, and sliding distance on the wear behavior of the composite. Analysis of variance was used to determine the most significant factors affecting wear. The results of this study could help optimize composite brake materials to improve braking performance and durability.
Polymers are presently broadly utilized as substitute material for steel gear in low
load devices. Its malfunction differs from gears made of steel, thus it is imperitive to sort
out the failures shown by polymer gears. Numerous earlier studies noted that wear
recognition, microstructure surface condition monitoring, weight loss and temperature
detection can be used in the analysis for the failure of polymer gear. The principle
objective of the current work is to conduct an analysis for failure detection methods as
defined above. Other researcher works were studied and their findings were extracted in
order to identify the methods they used. The most common method used was wear
detection and it was supplemented by other methods such as microstructure surface
condition monitoring. Failures shown by polymer can be concluded to be tooth breakage,
tooth deformation, material removal and surface fatigue.
Experimental Study of Wear Rate Coefficient of Aluminium Hybrid Composites Ma...AM Publications
In current decade, demand in material characteristics like light weight, superior strength to weight ratio, improved surface properties and enhanced wear resistance for complex engineering applications like automobile, aerospace and nuclear are researcher’s interest. However, performance of hybrid composites depends on right combination of reinforcements. Silicon carbide, silicon nitride, boron nitride and titanium carbide are few reinforcements available at present. In this work, Al356 is reinforced with SiC and B4C to enhance the mechanical properties, surface hardness and wear resistance. This hybrid composite is prepared by stir casting technique and the morphology of composite is studied using optical microscope to investigate the dispersion of reinforcements. In the present study, the wear and friction characteristics of hybrid composites are investigated using pin on disc dry wear tests by varying the load and speed and the results are tabulated for load vs mass loss, load vs wear rate and load vs wear coefficient. The results report that wear rate of hybrid composites are lower than that of binary composites. Mechanical properties, surface hardness and wear characteristics of aluminium hybrid composites are compared with that of aluminium binary composites available at present.
Studies On Microstructure And Mechanical Properties Of Flyash Reinforced Al20...dbpublications
The aim is to study the mechanical property and Tribological behavior of Al2024/flyash composite with various weight fractions (3%, 6%, 9%) were prepared by squeeze casting method. The average particle size of flyash is 45-50 μm. In addition, Al2024 alloys were cast for comparison purposes. Microstructure, hardness and tensile properties of these composites were evaluated and compared with as-cast alloy and the composites. In addition, tribological properties of these composites were evaluated using a Pin-on-Disc apparatus with different parameters of varying loads of 10N and 50N and(with constant parameters such as time of 10 minutes, sliding velocity of 3 m/s, track diameter of 150mm).The microstructure of the composites shows homogenous distribution of flyash particles in the Al matrix composite. The wear and mechanical properties of composites improve with increasing the weight fraction of flyash. The aim of present study is to evaluate the effect of microstructure, mechanical and tribological properties of aluminium alloy Al2024/flyash metal matrix composites
Polymers are presently broadly utilized as substitute material for steel gear in low
load devices. Its malfunction differs from gears made of steel, thus it is imperitive to sort
out the failures shown by polymer gears. Numerous earlier studies noted that wear
recognition, microstructure surface condition monitoring, weight loss and temperature
detection can be used in the analysis for the failure of polymer gear. The principle
objective of the current work is to conduct an analysis for failure detection methods as
defined above. Other researcher works were studied and their findings were extracted in
order to identify the methods they used. The most common method used was wear
detection and it was supplemented by other methods such as microstructure surface
condition monitoring. Failures shown by polymer can be concluded to be tooth breakage,
tooth deformation, material removal and surface fatigue.
Experimental Study of Wear Rate Coefficient of Aluminium Hybrid Composites Ma...AM Publications
In current decade, demand in material characteristics like light weight, superior strength to weight ratio, improved surface properties and enhanced wear resistance for complex engineering applications like automobile, aerospace and nuclear are researcher’s interest. However, performance of hybrid composites depends on right combination of reinforcements. Silicon carbide, silicon nitride, boron nitride and titanium carbide are few reinforcements available at present. In this work, Al356 is reinforced with SiC and B4C to enhance the mechanical properties, surface hardness and wear resistance. This hybrid composite is prepared by stir casting technique and the morphology of composite is studied using optical microscope to investigate the dispersion of reinforcements. In the present study, the wear and friction characteristics of hybrid composites are investigated using pin on disc dry wear tests by varying the load and speed and the results are tabulated for load vs mass loss, load vs wear rate and load vs wear coefficient. The results report that wear rate of hybrid composites are lower than that of binary composites. Mechanical properties, surface hardness and wear characteristics of aluminium hybrid composites are compared with that of aluminium binary composites available at present.
Studies On Microstructure And Mechanical Properties Of Flyash Reinforced Al20...dbpublications
The aim is to study the mechanical property and Tribological behavior of Al2024/flyash composite with various weight fractions (3%, 6%, 9%) were prepared by squeeze casting method. The average particle size of flyash is 45-50 μm. In addition, Al2024 alloys were cast for comparison purposes. Microstructure, hardness and tensile properties of these composites were evaluated and compared with as-cast alloy and the composites. In addition, tribological properties of these composites were evaluated using a Pin-on-Disc apparatus with different parameters of varying loads of 10N and 50N and(with constant parameters such as time of 10 minutes, sliding velocity of 3 m/s, track diameter of 150mm).The microstructure of the composites shows homogenous distribution of flyash particles in the Al matrix composite. The wear and mechanical properties of composites improve with increasing the weight fraction of flyash. The aim of present study is to evaluate the effect of microstructure, mechanical and tribological properties of aluminium alloy Al2024/flyash metal matrix composites
Modelling and Analysis of Hybrid Composite Joint Using Fem in ANSYSIJMER
Composite materials are widely used in the various Fields. Due to the high strength they
arewidelyusedinthelowweightconstructionsandalsousedasasuitablealternativetometals.Invariousapplicat
ionsAnd also for joining various composite parts together, they are fastened together using adhesives or
Mechanical fasteners. Modelling and static analysis of 3-D Models of joints such as bonded, riveted and
hybrid. The results were found in terms of von-mises stress, shear stress and normal stress for stress
distribution. ANSYS FEA tool has been used for stress distribution characteristics of various
configurations of double riveted single lap joint with three joining methods namely bonded, riveted and
hybrid the present study deals with the analysis of single lap joint subjected to the given tensile load and
the stress distribution in the members under various design conditions are found
Modelling and Analysis of Hybrid Composite Joint Using Fem in AnsysIOSR Journals
Abstract: Composite materials are widely used in the various Fields. Due to the high strength they are widely
used in the low weight constructions and also used as a suitable alternative to metals. In various applications
and also for joining various composite parts together, they are fastened together using adhesives or Mechanical
fasteners. Modeling and static analysis of 3-D Models of joints such as bonded, riveted and hybrid. The results
were found in terms of vonmises stress, shear stress, and normal stress for stress distribution. ANSYS FEA tool
has been used for stress distribution characteristics of various configurations of double riveted single lap joint
with three joining methods namely bonded, riveted and hybrid the present study deals with the analysis of single
lap joint subjected to the given tensile load and the stress distribution in the members under various design
conditions are found.
Aluminium Matrix Composites (AMC’s) are widely used in aerospace, automotive,
structural and marine applications due to their high strength to weight ratio, corrosion
resistance. In AMC one of constituent is aluminium or its alloy which forms a network
called as matrix phase and other constituent is embedded in matrix made of harder material
generally ceramic or non metallic material called as reinforcement. Various processing
techniques are available for manufacturing of AMC’s. Stir casting is one of the economical
and extensively used methods to enhance attractive properties of AMC’s. This paper
presents an overview of stir casing process, process parameter and preparation of AMC
using aluminium alloy as matrix phase and alumina (Al2O3) as reinforcement by varying
their proportion.
High performance polymer fibre reinforced metal matrix composites- Metal Orga...Padmanabhan Krishnan
Zylon reinforced aluminium, zinc and lead low melting metal matrix composites that broadly belong to the MOF ( Metal Organic Framework ) materials were processed, characterised and measured for their properties and foreseen applications.
Computational Analysis of Fatigue of Glass/Epoxy Composite Automobile Drive S...AM Publications
Composites offer significant improvement over current available materials for automobile due to their excellent mechanical characteristics and relatively low density. Fatigue life of composite drive shaft with viscous interface under variable torsion loads is analyzed. The Stress intensity is obtained explicitly by using micromechanical model of composites. The study indicates that the life of the composite depends on several factors, including fiber volume fraction, the relative shear rigidity of fiber to matrix, and a dimensionless parameter composed of interface viscosity, fiber radius, vibration frequency and shear modulus of matrix. Computationalapproach is adopted for analyzing the fatigue life of composite drive shaft. Stress intensity factor will be developed using a finite element analysis depends on the material directions of the layers. Glass fiber and Epoxy composite material is considered for designing the drive shaft.
This paper examines the dry sliding wear conduct of A356/TiB2 aluminum composite
arranged by the stir casting setup. A pin-on-disc wear contraption was utilized for this
examination. The impact of TiB2 particulate substance and ordinary load on wear rate
was broke down. The insitu created TiB2 strengthened particles upgrades the wear
opposition of the A356 composite. The outcomes demonstrated that TiB2 particles were
successful to expand the wear opposition of the composite. The worn surface examination
of the composite as an element of Titanium diboride particulate substance and ordinary
load are likewise displayed
Strength Analysis of Aluminium Composite Reinforced with Coconut Ash Powder A...ijtsrd
The strength of Al 6063 and against its reinforced samples using coconut husk has been analysed. The wide range of applications of these metals lies in the field of aeronautical engineering, automobile engineering, marine Industry, military and also in the architectural field. The different tests which have been carried out on this metal and its composites are UTM, Brinell test and Impact test. Muhib-Ul-Hussian | Dr. Gautam Kocher | Er Pradeep Singh "Strength Analysis of Aluminium Composite Reinforced with Coconut Ash Powder: A Review" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-4 | Issue-3 , April 2020, URL: https://www.ijtsrd.com/papers/ijtsrd30525.pdf Paper Url :https://www.ijtsrd.com/engineering/mechanical-engineering/30525/strength-analysis-of-aluminium-composite-reinforced-with-coconut-ash-powder-a-review/muhibulhussian
A Review on Investigation of Tribological Behavior of Nanocoating for Piston ...IJLT EMAS
Nanocoating can help to improve performance and life
of automotive engine by reducing the wear between the engine
components. In this research have selected the proper material
for top piston ring and same material are to be selected for
preparation of pin for tribometer testing and material of cylinder
liner tested and fabricated the same material of tribometer disc.
Nanocoating by electroplated Chromium coating and Chromium
nitride using DLC method by PVD coating was done on
specimen pin and piston ring and this material which was used
tribometer testing.
Depleting fossil fuel resources, economic
competitiveness and environmental concerns has compelled to
explore newer avenues to improve efficiency of automotive
engines. Various techniques have been adapted to achieve this
goal.
An Overview on Different Processing Parameters in Particulate Reinforced Meta...IJERA Editor
In the past few years the global need for reduced weight, low cost, high wear resistance and good quality materials has caused a shift in research from monolithic to composite materials. Metal Matrix Composites (MMCs) have evoked a keen interest in recent times for potential applications in marine, aerospace and automotive industries owing to their superior strength to weight ratio and high temperature resistance. Driving force for the utilization of AMCs include performance, economic and environmental benefits. The widespread adoption of particulate metal matrix composites for engineering applications has been hindered by the high cost of producing components. Achieving a uniform distribution of reinforcement within the matrix is one such challenge which impacts directly on the properties and quality of the composite material. In the case of particle reinforced metal matrix composites, the distribution of the reinforcement particles in the matrix alloy is influenced by several factors during casting. These include the rheological behaviour of the matrix melt, the particle incorporation method, interactions of the particles and the matrix before, during and after mixing, and the changing particle distribution during solidification. In this paper, research relevant to these factors which influences the particle distribution is reviewed and discussed in order to achieve a good distribution of reinforcement particles in a cast metal matrix composite (MMC).
ANALYSIS AND EXPERIMENTAL VALIDATION OF COMPOSITE LAP JOINT WITH CRACK FOR AE...IAEME Publication
Composite materials have made way to several different fields, including
aerospace structures, under water vehicles, automobiles and robot systems etc. Due to
the high strength they are widely used in the low weight constructions and also used
as a suitable alternative to metals. ANSYS FEA tool has been used for stress
distribution characteristics of single lap joint with crack in-built in adhesive layer. In
several different applications and also for joining various composite parts together, by
using epoxy adhesives. Modeling and static analysis of 3D Models of lap joints were
carried out and compared for two different composite materials. The present study
deals with the analysis of single lap joint subjected to tensile load and the stress
distribution in the joint members under various design conditions are to be found.
The fracture characteristics of single-lap bonded joints in composites to be
investigated by structural analysis and experimentally. The effects of bonding method,
surface roughness, bond line thickness and the existence of fillet on the failure
characteristics and strength of bonded single-lap joints were evaluated
experimentally. The failure process, failure mode and the behavior of loaddisplacement
curve was apparently different according to bonding method to be
evaluated
Modelling and Analysis of Hybrid Composite Joint Using Fem in ANSYSIJMER
Composite materials are widely used in the various Fields. Due to the high strength they
arewidelyusedinthelowweightconstructionsandalsousedasasuitablealternativetometals.Invariousapplicat
ionsAnd also for joining various composite parts together, they are fastened together using adhesives or
Mechanical fasteners. Modelling and static analysis of 3-D Models of joints such as bonded, riveted and
hybrid. The results were found in terms of von-mises stress, shear stress and normal stress for stress
distribution. ANSYS FEA tool has been used for stress distribution characteristics of various
configurations of double riveted single lap joint with three joining methods namely bonded, riveted and
hybrid the present study deals with the analysis of single lap joint subjected to the given tensile load and
the stress distribution in the members under various design conditions are found
Modelling and Analysis of Hybrid Composite Joint Using Fem in AnsysIOSR Journals
Abstract: Composite materials are widely used in the various Fields. Due to the high strength they are widely
used in the low weight constructions and also used as a suitable alternative to metals. In various applications
and also for joining various composite parts together, they are fastened together using adhesives or Mechanical
fasteners. Modeling and static analysis of 3-D Models of joints such as bonded, riveted and hybrid. The results
were found in terms of vonmises stress, shear stress, and normal stress for stress distribution. ANSYS FEA tool
has been used for stress distribution characteristics of various configurations of double riveted single lap joint
with three joining methods namely bonded, riveted and hybrid the present study deals with the analysis of single
lap joint subjected to the given tensile load and the stress distribution in the members under various design
conditions are found.
Aluminium Matrix Composites (AMC’s) are widely used in aerospace, automotive,
structural and marine applications due to their high strength to weight ratio, corrosion
resistance. In AMC one of constituent is aluminium or its alloy which forms a network
called as matrix phase and other constituent is embedded in matrix made of harder material
generally ceramic or non metallic material called as reinforcement. Various processing
techniques are available for manufacturing of AMC’s. Stir casting is one of the economical
and extensively used methods to enhance attractive properties of AMC’s. This paper
presents an overview of stir casing process, process parameter and preparation of AMC
using aluminium alloy as matrix phase and alumina (Al2O3) as reinforcement by varying
their proportion.
High performance polymer fibre reinforced metal matrix composites- Metal Orga...Padmanabhan Krishnan
Zylon reinforced aluminium, zinc and lead low melting metal matrix composites that broadly belong to the MOF ( Metal Organic Framework ) materials were processed, characterised and measured for their properties and foreseen applications.
Computational Analysis of Fatigue of Glass/Epoxy Composite Automobile Drive S...AM Publications
Composites offer significant improvement over current available materials for automobile due to their excellent mechanical characteristics and relatively low density. Fatigue life of composite drive shaft with viscous interface under variable torsion loads is analyzed. The Stress intensity is obtained explicitly by using micromechanical model of composites. The study indicates that the life of the composite depends on several factors, including fiber volume fraction, the relative shear rigidity of fiber to matrix, and a dimensionless parameter composed of interface viscosity, fiber radius, vibration frequency and shear modulus of matrix. Computationalapproach is adopted for analyzing the fatigue life of composite drive shaft. Stress intensity factor will be developed using a finite element analysis depends on the material directions of the layers. Glass fiber and Epoxy composite material is considered for designing the drive shaft.
This paper examines the dry sliding wear conduct of A356/TiB2 aluminum composite
arranged by the stir casting setup. A pin-on-disc wear contraption was utilized for this
examination. The impact of TiB2 particulate substance and ordinary load on wear rate
was broke down. The insitu created TiB2 strengthened particles upgrades the wear
opposition of the A356 composite. The outcomes demonstrated that TiB2 particles were
successful to expand the wear opposition of the composite. The worn surface examination
of the composite as an element of Titanium diboride particulate substance and ordinary
load are likewise displayed
Strength Analysis of Aluminium Composite Reinforced with Coconut Ash Powder A...ijtsrd
The strength of Al 6063 and against its reinforced samples using coconut husk has been analysed. The wide range of applications of these metals lies in the field of aeronautical engineering, automobile engineering, marine Industry, military and also in the architectural field. The different tests which have been carried out on this metal and its composites are UTM, Brinell test and Impact test. Muhib-Ul-Hussian | Dr. Gautam Kocher | Er Pradeep Singh "Strength Analysis of Aluminium Composite Reinforced with Coconut Ash Powder: A Review" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-4 | Issue-3 , April 2020, URL: https://www.ijtsrd.com/papers/ijtsrd30525.pdf Paper Url :https://www.ijtsrd.com/engineering/mechanical-engineering/30525/strength-analysis-of-aluminium-composite-reinforced-with-coconut-ash-powder-a-review/muhibulhussian
A Review on Investigation of Tribological Behavior of Nanocoating for Piston ...IJLT EMAS
Nanocoating can help to improve performance and life
of automotive engine by reducing the wear between the engine
components. In this research have selected the proper material
for top piston ring and same material are to be selected for
preparation of pin for tribometer testing and material of cylinder
liner tested and fabricated the same material of tribometer disc.
Nanocoating by electroplated Chromium coating and Chromium
nitride using DLC method by PVD coating was done on
specimen pin and piston ring and this material which was used
tribometer testing.
Depleting fossil fuel resources, economic
competitiveness and environmental concerns has compelled to
explore newer avenues to improve efficiency of automotive
engines. Various techniques have been adapted to achieve this
goal.
An Overview on Different Processing Parameters in Particulate Reinforced Meta...IJERA Editor
In the past few years the global need for reduced weight, low cost, high wear resistance and good quality materials has caused a shift in research from monolithic to composite materials. Metal Matrix Composites (MMCs) have evoked a keen interest in recent times for potential applications in marine, aerospace and automotive industries owing to their superior strength to weight ratio and high temperature resistance. Driving force for the utilization of AMCs include performance, economic and environmental benefits. The widespread adoption of particulate metal matrix composites for engineering applications has been hindered by the high cost of producing components. Achieving a uniform distribution of reinforcement within the matrix is one such challenge which impacts directly on the properties and quality of the composite material. In the case of particle reinforced metal matrix composites, the distribution of the reinforcement particles in the matrix alloy is influenced by several factors during casting. These include the rheological behaviour of the matrix melt, the particle incorporation method, interactions of the particles and the matrix before, during and after mixing, and the changing particle distribution during solidification. In this paper, research relevant to these factors which influences the particle distribution is reviewed and discussed in order to achieve a good distribution of reinforcement particles in a cast metal matrix composite (MMC).
ANALYSIS AND EXPERIMENTAL VALIDATION OF COMPOSITE LAP JOINT WITH CRACK FOR AE...IAEME Publication
Composite materials have made way to several different fields, including
aerospace structures, under water vehicles, automobiles and robot systems etc. Due to
the high strength they are widely used in the low weight constructions and also used
as a suitable alternative to metals. ANSYS FEA tool has been used for stress
distribution characteristics of single lap joint with crack in-built in adhesive layer. In
several different applications and also for joining various composite parts together, by
using epoxy adhesives. Modeling and static analysis of 3D Models of lap joints were
carried out and compared for two different composite materials. The present study
deals with the analysis of single lap joint subjected to tensile load and the stress
distribution in the joint members under various design conditions are to be found.
The fracture characteristics of single-lap bonded joints in composites to be
investigated by structural analysis and experimentally. The effects of bonding method,
surface roughness, bond line thickness and the existence of fillet on the failure
characteristics and strength of bonded single-lap joints were evaluated
experimentally. The failure process, failure mode and the behavior of loaddisplacement
curve was apparently different according to bonding method to be
evaluated
Experimental Investigation of Wear Properties of Aluminium LM25 Red Mud Metal...IJSRD
The use of different kind of Metal-matrix composite materials is in constant growing over the years, because they have better physical, mechanical and tribological properties comparing to matrix materials. In automotive industry they are used for pistons, cylinders, engine blocks, brakes and power transfer system elements. Research attempts have been made in the past toreduce the cost of processing of composites, decrease the weight of the composites, and increase the desired performance characteristics. This paper presents the findings of an experimental investigation on the effects of applied load, RPM, Sliding distance and pin temperature in dry sliding wear studies performed on red mud-based aluminum metal matrix composites (MMC). Red mud is an industrial waste during the production of aluminum from bauxite ore. A pin-on-disc apparatus was used to conduct the dry sliding wear test. Taguchi-based L9 orthogonal array has been used to accomplish the objective of the experimental study. Analysis of variance (ANOVA) is employed to find the optimal setting and the effect of each parameter on wear rate.
Evaluation Of Factors Affecting Sliding Wear Behaviour Of Al-Flyash Metal Mat...IJMER
International Journal of Modern Engineering Research (IJMER) is Peer reviewed, online Journal. It serves as an international archival forum of scholarly research related to engineering and science education.
International Journal of Computational Engineering Research(IJCER)ijceronline
International Journal of Computational Engineering Research(IJCER) is an intentional online Journal in English monthly publishing journal. This Journal publish original research work that contributes significantly to further the scientific knowledge in engineering and Technology.
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
HEAP SORT ILLUSTRATED WITH HEAPIFY, BUILD HEAP FOR DYNAMIC ARRAYS.
Heap sort is a comparison-based sorting technique based on Binary Heap data structure. It is similar to the selection sort where we first find the minimum element and place the minimum element at the beginning. Repeat the same process for the remaining elements.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
Using recycled concrete aggregates (RCA) for pavements is crucial to achieving sustainability. Implementing RCA for new pavement can minimize carbon footprint, conserve natural resources, reduce harmful emissions, and lower life cycle costs. Compared to natural aggregate (NA), RCA pavement has fewer comprehensive studies and sustainability assessments.
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...Amil Baba Dawood bangali
Contact with Dawood Bhai Just call on +92322-6382012 and we'll help you. We'll solve all your problems within 12 to 24 hours and with 101% guarantee and with astrology systematic. If you want to take any personal or professional advice then also you can call us on +92322-6382012 , ONLINE LOVE PROBLEM & Other all types of Daily Life Problem's.Then CALL or WHATSAPP us on +92322-6382012 and Get all these problems solutions here by Amil Baba DAWOOD BANGALI
#vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore#blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #blackmagicforlove #blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #Amilbabainuk #amilbabainspain #amilbabaindubai #Amilbabainnorway #amilbabainkrachi #amilbabainlahore #amilbabaingujranwalan #amilbabainislamabad
Forklift Classes Overview by Intella PartsIntella Parts
Discover the different forklift classes and their specific applications. Learn how to choose the right forklift for your needs to ensure safety, efficiency, and compliance in your operations.
For more technical information, visit our website https://intellaparts.com
KuberTENes Birthday Bash Guadalajara - K8sGPT first impressionsVictor Morales
K8sGPT is a tool that analyzes and diagnoses Kubernetes clusters. This presentation was used to share the requirements and dependencies to deploy K8sGPT in a local environment.