This document summarizes seismic analysis of an open ground storey framed building with three different models in Etabs software. Model 1 has load bearing walls at every position without openings. Model 2 has load bearing outer walls and partition inner walls, with openings in the outer walls. Model 3 is the same as Model 2. The analysis compares base shear, storey drift, displacement, and time periods between the three models. Model 3 generally performed better with decreased time periods, increased storey stiffness in upper stories, and increased overturning moments, indicating it experienced greater seismic forces that the other models. The conclusion is that Model 3 provides better seismic performance than the other two structures.
Effect of base isolation in multistoried rc irregular building using time his...eSAT Journals
Abstract Base isolation (BI) is a technique that has been used around the world to protect the building structures from the damaging effects of earthquake. The installation of isolator in building at base level significantly increases the time period of the structure, which means it reduces the possibility of resonance of the structure giving rise to better seismic performance of the building. The study is performed to compare the effectiveness of base isolation in plan irregular and vertical irregular multi-storied RC frame building. For this study, 15 storied R.C frame building is considered and Time History analysis is carried out using ETABS 2013 software. The Lead Rubber Bearing (LRB) is designed as per UBC 97 code and the same was used for analysis of base isolation system. The results obtained from the analysis were time period and base shear. Time period for the base isolated structures are higher than that of the fixed base structure. Due to the presence of isolator, Base shear is significantly reduced in each direction (X and Y direction) as compared to fixed base building. It has been found that when compared to plan irregular base isolated building the vertical irregular building gives better performance in high seismic prone area by using isolators at the base of the building.
Keywords: Base isolation, Lead rubber bearing, Time history analysis, Irregular building
Diagrid structural system strategies to reduce lateral forces on high rise bu...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
Effect of base isolation in multistoried rc irregular building using time his...eSAT Journals
Abstract Base isolation (BI) is a technique that has been used around the world to protect the building structures from the damaging effects of earthquake. The installation of isolator in building at base level significantly increases the time period of the structure, which means it reduces the possibility of resonance of the structure giving rise to better seismic performance of the building. The study is performed to compare the effectiveness of base isolation in plan irregular and vertical irregular multi-storied RC frame building. For this study, 15 storied R.C frame building is considered and Time History analysis is carried out using ETABS 2013 software. The Lead Rubber Bearing (LRB) is designed as per UBC 97 code and the same was used for analysis of base isolation system. The results obtained from the analysis were time period and base shear. Time period for the base isolated structures are higher than that of the fixed base structure. Due to the presence of isolator, Base shear is significantly reduced in each direction (X and Y direction) as compared to fixed base building. It has been found that when compared to plan irregular base isolated building the vertical irregular building gives better performance in high seismic prone area by using isolators at the base of the building.
Keywords: Base isolation, Lead rubber bearing, Time history analysis, Irregular building
Diagrid structural system strategies to reduce lateral forces on high rise bu...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
Seismic analysis of high damping rubber bearings for base isolationeSAT Journals
Abstract
Base isolation is a mechanism that provides earthquake resistance to the new structure. The base isolation system decouples the building from the horizontal ground motion induced by earthquake, and offers very stiff vertical components to the base level of the superstructure in connection to substructure (foundation). It shifts the fundamental lateral period, dissipates the energy in damping, and reduces the amount of the lateral forces that transferred to the building, inter-story drift, and the floor acceleration.
The work deals with modelling and finite element analysis of a high damping rubber bearing in ANSYS 12.0. A displacement controlled transient analysis was done to analyse the behaviour of the isolator during earthquakes.
Keywords: Base isolation, High damping rubber, Transient analysis
Study on laminated rubber bearing base isolators for seismic protection of st...eSAT Journals
Abstract
Base isolation or seismic base isolation is an effective means for protection of structures, its contents and its occupants during the event of an earthquake. The principle of base isolation is vibration isolation. It decouples the building from damaging action of the earthquake. The isolator partially reflects and partially absorbs input seismic energy before it gets transmitted to the superstructure. Laminated Rubber Bearing Isolators are placed between the superstructure and foundation, which reduces the horizontal stiffness of the system. It thereby increases the time period of the structure and decreases the spectral acceleration of the structure. The superstructure acts like a rigid body, thus inter storey drift is reduced. Such type of isolators are used in practice in India, yet a proper design procedure based on IS code is unavailable. The paper presents design procedure for LRB adopting the procedure of IS 1893:2002 (Part-1) for earthquake resistant design of buildings. Design charts have been developed and presented in this paper which gives isolator diameter and rubber thickness as design outputs. The design procedure requires different input parameters like fundamental period and damping of the fixed base structure, axial load on the column, seismic zone, type of soil and shore hardness of rubber. These design charts enable the designer to easily arrive at the isolator parameters to achieve seismic isolation. Using the charts, case study has been done using SAP2000. Building displacement and acceleration are compared for model with and without base isolator. Comparative study of linear and non-linear base isolators has also been carried out. Linear and non-linear time history analysis has been done using El Centro earthquake.
Keywords: base isolation, laminated rubber bearing, IS Code, seismic protection, design charts, time history analysis, SAP2000
Optimization of a multistorey building by optimum positioning of shear walleSAT Journals
Abstract The shear wall is a structural element which is used to resist earthquake forces. These wall will consumptives shear forces & will prevent changing location-position of construction & consequently destruction. On other hand, shear wall arrangement must be absolutely accurate, if not, we will find negative effect instead. For example if the shear walls make an increase distance between mass centre and hardness centre, we cannot expect a good tensional behavior from the structure. In case of mass centre and hardness centre coincide with each other, at that time the distance of shear wall from the mass centre also plays an important role in the shear contribution of the shear wall. The bending moment, shear force, torsion, axial force contribution by rest of the structural element and the ultimate design of all the structural components also affected by that. A study has been carried out to determine the optimum Structural configuration of a multistory building by changing the shear wall locations radically. Four different cases of shear wall position for a 10 storey residential building with keeping zero eccentricity between mass centre and hardness centre have been analyzed and designed as a space frame system by computer application software, subjected to lateral and gravity loading in accordance with IS provisions. Keywords: Shear walls, Lateral loading, Zero eccentricity, Stresses, Design configuration.
Case study on slender multi storey rc building with brick infilleSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
A study on behaviour of outrigger system on high rise steel structure by vary...eSAT Journals
Abstract The outrigger system is one of the most efficient system used for high rise structures to resist lateral forces. In the present study an attempt has been made to study the static and dynamic behavior of the outrigger structural system on steel structure by reducing the depth of outrigger.5X5 bay 40 story 3D steel structures is modeled in ETABS v2013 software. Steel structure with central core and steel structure with outrigger structural system of varied depth of outrigger are compared. The depth of the outrigger is reduced to 2/3rd and 1/3rd of the story height along with the full story height. The depth of the belt-truss is equal to the height of the typical story and maintained same in all the structures. The key parameters discussed in this paper include lateral deflection and storey drift. From the analysis results it has been found that the comparative performance of outrigger with depth of full storey height and decreased depth shows minor difference in resistance towards lateral loads. Keywords: Outrigger system, Lateral Displacement, Inter story drift
Explains in detail about the planning and designing of a G + 2 school building both manually and using software (STAAD Pro).
With the reference with this we could design a building of a school with 2 blocks and G + 2 building.
Seismic analysis of high damping rubber bearings for base isolationeSAT Journals
Abstract
Base isolation is a mechanism that provides earthquake resistance to the new structure. The base isolation system decouples the building from the horizontal ground motion induced by earthquake, and offers very stiff vertical components to the base level of the superstructure in connection to substructure (foundation). It shifts the fundamental lateral period, dissipates the energy in damping, and reduces the amount of the lateral forces that transferred to the building, inter-story drift, and the floor acceleration.
The work deals with modelling and finite element analysis of a high damping rubber bearing in ANSYS 12.0. A displacement controlled transient analysis was done to analyse the behaviour of the isolator during earthquakes.
Keywords: Base isolation, High damping rubber, Transient analysis
Study on laminated rubber bearing base isolators for seismic protection of st...eSAT Journals
Abstract
Base isolation or seismic base isolation is an effective means for protection of structures, its contents and its occupants during the event of an earthquake. The principle of base isolation is vibration isolation. It decouples the building from damaging action of the earthquake. The isolator partially reflects and partially absorbs input seismic energy before it gets transmitted to the superstructure. Laminated Rubber Bearing Isolators are placed between the superstructure and foundation, which reduces the horizontal stiffness of the system. It thereby increases the time period of the structure and decreases the spectral acceleration of the structure. The superstructure acts like a rigid body, thus inter storey drift is reduced. Such type of isolators are used in practice in India, yet a proper design procedure based on IS code is unavailable. The paper presents design procedure for LRB adopting the procedure of IS 1893:2002 (Part-1) for earthquake resistant design of buildings. Design charts have been developed and presented in this paper which gives isolator diameter and rubber thickness as design outputs. The design procedure requires different input parameters like fundamental period and damping of the fixed base structure, axial load on the column, seismic zone, type of soil and shore hardness of rubber. These design charts enable the designer to easily arrive at the isolator parameters to achieve seismic isolation. Using the charts, case study has been done using SAP2000. Building displacement and acceleration are compared for model with and without base isolator. Comparative study of linear and non-linear base isolators has also been carried out. Linear and non-linear time history analysis has been done using El Centro earthquake.
Keywords: base isolation, laminated rubber bearing, IS Code, seismic protection, design charts, time history analysis, SAP2000
Optimization of a multistorey building by optimum positioning of shear walleSAT Journals
Abstract The shear wall is a structural element which is used to resist earthquake forces. These wall will consumptives shear forces & will prevent changing location-position of construction & consequently destruction. On other hand, shear wall arrangement must be absolutely accurate, if not, we will find negative effect instead. For example if the shear walls make an increase distance between mass centre and hardness centre, we cannot expect a good tensional behavior from the structure. In case of mass centre and hardness centre coincide with each other, at that time the distance of shear wall from the mass centre also plays an important role in the shear contribution of the shear wall. The bending moment, shear force, torsion, axial force contribution by rest of the structural element and the ultimate design of all the structural components also affected by that. A study has been carried out to determine the optimum Structural configuration of a multistory building by changing the shear wall locations radically. Four different cases of shear wall position for a 10 storey residential building with keeping zero eccentricity between mass centre and hardness centre have been analyzed and designed as a space frame system by computer application software, subjected to lateral and gravity loading in accordance with IS provisions. Keywords: Shear walls, Lateral loading, Zero eccentricity, Stresses, Design configuration.
Case study on slender multi storey rc building with brick infilleSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
A study on behaviour of outrigger system on high rise steel structure by vary...eSAT Journals
Abstract The outrigger system is one of the most efficient system used for high rise structures to resist lateral forces. In the present study an attempt has been made to study the static and dynamic behavior of the outrigger structural system on steel structure by reducing the depth of outrigger.5X5 bay 40 story 3D steel structures is modeled in ETABS v2013 software. Steel structure with central core and steel structure with outrigger structural system of varied depth of outrigger are compared. The depth of the outrigger is reduced to 2/3rd and 1/3rd of the story height along with the full story height. The depth of the belt-truss is equal to the height of the typical story and maintained same in all the structures. The key parameters discussed in this paper include lateral deflection and storey drift. From the analysis results it has been found that the comparative performance of outrigger with depth of full storey height and decreased depth shows minor difference in resistance towards lateral loads. Keywords: Outrigger system, Lateral Displacement, Inter story drift
Explains in detail about the planning and designing of a G + 2 school building both manually and using software (STAAD Pro).
With the reference with this we could design a building of a school with 2 blocks and G + 2 building.
Behavioural studies of floating column on framed structureeSAT Journals
Abstract RCC concrete column means cement concrete reinforced with steel bars, steel plates, steel mesh etc. to increase the tension withstanding capacity of the structure. The term floating column means that the column is floated between two floors. Various types of structures G+3, G+5 and G+10 for RCC column and floating column are analyzed. The difference between G+3, G+5 and G+ 10 structures are shown by graphs and charts. Comparison will be done on bending moment and shear force between these structures. This paper presents the analysis of floating column and RCC column by using STAAD PRO V8i. Keywords: Floating Column, RCC column shear force and bending moment.
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
TECHNICAL TRAINING MANUAL GENERAL FAMILIARIZATION COURSEDuvanRamosGarzon1
AIRCRAFT GENERAL
The Single Aisle is the most advanced family aircraft in service today, with fly-by-wire flight controls.
The A318, A319, A320 and A321 are twin-engine subsonic medium range aircraft.
The family offers a choice of engines
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
Automobile Management System Project Report.pdfKamal Acharya
The proposed project is developed to manage the automobile in the automobile dealer company. The main module in this project is login, automobile management, customer management, sales, complaints and reports. The first module is the login. The automobile showroom owner should login to the project for usage. The username and password are verified and if it is correct, next form opens. If the username and password are not correct, it shows the error message.
When a customer search for a automobile, if the automobile is available, they will be taken to a page that shows the details of the automobile including automobile name, automobile ID, quantity, price etc. “Automobile Management System” is useful for maintaining automobiles, customers effectively and hence helps for establishing good relation between customer and automobile organization. It contains various customized modules for effectively maintaining automobiles and stock information accurately and safely.
When the automobile is sold to the customer, stock will be reduced automatically. When a new purchase is made, stock will be increased automatically. While selecting automobiles for sale, the proposed software will automatically check for total number of available stock of that particular item, if the total stock of that particular item is less than 5, software will notify the user to purchase the particular item.
Also when the user tries to sale items which are not in stock, the system will prompt the user that the stock is not enough. Customers of this system can search for a automobile; can purchase a automobile easily by selecting fast. On the other hand the stock of automobiles can be maintained perfectly by the automobile shop manager overcoming the drawbacks of existing system.
Democratizing Fuzzing at Scale by Abhishek Aryaabh.arya
Presented at NUS: Fuzzing and Software Security Summer School 2024
This keynote talks about the democratization of fuzzing at scale, highlighting the collaboration between open source communities, academia, and industry to advance the field of fuzzing. It delves into the history of fuzzing, the development of scalable fuzzing platforms, and the empowerment of community-driven research. The talk will further discuss recent advancements leveraging AI/ML and offer insights into the future evolution of the fuzzing landscape.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
Vaccine management system project report documentation..pdfKamal Acharya
The Division of Vaccine and Immunization is facing increasing difficulty monitoring vaccines and other commodities distribution once they have been distributed from the national stores. With the introduction of new vaccines, more challenges have been anticipated with this additions posing serious threat to the already over strained vaccine supply chain system in Kenya.
Explore the innovative world of trenchless pipe repair with our comprehensive guide, "The Benefits and Techniques of Trenchless Pipe Repair." This document delves into the modern methods of repairing underground pipes without the need for extensive excavation, highlighting the numerous advantages and the latest techniques used in the industry.
Learn about the cost savings, reduced environmental impact, and minimal disruption associated with trenchless technology. Discover detailed explanations of popular techniques such as pipe bursting, cured-in-place pipe (CIPP) lining, and directional drilling. Understand how these methods can be applied to various types of infrastructure, from residential plumbing to large-scale municipal systems.
Ideal for homeowners, contractors, engineers, and anyone interested in modern plumbing solutions, this guide provides valuable insights into why trenchless pipe repair is becoming the preferred choice for pipe rehabilitation. Stay informed about the latest advancements and best practices in the field.
Event Management System Vb Net Project Report.pdfKamal Acharya
In present era, the scopes of information technology growing with a very fast .We do not see any are untouched from this industry. The scope of information technology has become wider includes: Business and industry. Household Business, Communication, Education, Entertainment, Science, Medicine, Engineering, Distance Learning, Weather Forecasting. Carrier Searching and so on.
My project named “Event Management System” is software that store and maintained all events coordinated in college. It also helpful to print related reports. My project will help to record the events coordinated by faculties with their Name, Event subject, date & details in an efficient & effective ways.
In my system we have to make a system by which a user can record all events coordinated by a particular faculty. In our proposed system some more featured are added which differs it from the existing system such as security.