This document describes an automotive collision avoidance system that uses ultrasonic sensors and vibration sensors. The ultrasonic sensors continuously measure the distance to nearby obstacles and alert the microcontroller if an object gets too close. This causes the vehicle's speed to automatically decrease for safety. Vibration sensors detect collisions and trigger the microcontroller to transmit vehicle details to the other vehicle using Zigbee communication. This system aims to prevent front and rear collisions and help identify vehicles involved in accidents.
Response time analysis of mixed messages in CANIJERA Editor
Controller Area Network (CAN) is a network protocol that allows multiple processors in a system to
communicate efficiently with each other. Microprocessors became small enough and powerful enough to start
appearing everywhere, not just inside personal computers. A CAN system sends messages using a serial bus
network, with the individual nodes (processors) in the network linked together in a daisy chain. Every node in
the system is equal to every other node. Any processor can send a message to any other processor, and if any
processor fails, the other systems in the machine will continue to work properly and communicate with each
other.In modern vehicle technology CAN is used to reduce point to point wiring harness for vehicle automation
and for data communication. To overcome the drawbacks of analog vehicle driving interface, this paper presents
the development and implementation of a digital driving system for a semi-autonomous vehicle to improve the
driver-vehicle interface. This offers increased flexibility and expandability. This system uses sensors to
measure temperature, distance from the other car, presence of alcohol in car, position monitoring, theft
monitoring and etc., and sends a warning signal to the driver if any of the parameter goes out of range to avoid
accidents. In addition to this if accident occurs in any remote area then using vibration sensor, accident is
detected and SMS is send immediately using GSM and preventing him from potentially getting into a serious
problems.
As the rising of transportation system design, so many data logger design was developed for safety. In our country, there are
many accidents on highways. Both driver’s faults and road construction cause accidents. To reduce these condition some safety
system such as obstacle detection system, vehicle declination alarm system, temperature and smoke level display unit,
signboard warning on road sides should be used for both driver and passengers. In addition data logger system for whole
vehicle must be equipped for safety. With the implementation of PIC microcontroller as an Embedded device, this logger
design was constructed with many sensors and C# service-based database. Using Arduino boards, vehicle detection sensing
circuit, Check point radio signal sensing circuit for dangerous road sector, hall-effect magnetic wheel revolution sensing circuit
were designed to be connected with main PIC microcontroller and Personal Computer. Real time result was displayed on C#
Graphical User Interface and Vehicle data log could be easily exported to Microsoft Excel report.
Keywords -Arduino, alarm and alert system,C# service-based database, PC based control system, Vehicle data
logger.
The main objective of our project is to provide an optimum solution to the traffic hazards and the road accidents. According to this project when a vehicle meets with an accident, immediately vibration sensor will detect the signal and sends it to ARM controller. Microcontroller sends the alert message through the GSM MODEM including the location to police control room or a rescue team. So the police can immediately trace the location through the GPS MODEM after receiving the information.
Response time analysis of mixed messages in CANIJERA Editor
Controller Area Network (CAN) is a network protocol that allows multiple processors in a system to
communicate efficiently with each other. Microprocessors became small enough and powerful enough to start
appearing everywhere, not just inside personal computers. A CAN system sends messages using a serial bus
network, with the individual nodes (processors) in the network linked together in a daisy chain. Every node in
the system is equal to every other node. Any processor can send a message to any other processor, and if any
processor fails, the other systems in the machine will continue to work properly and communicate with each
other.In modern vehicle technology CAN is used to reduce point to point wiring harness for vehicle automation
and for data communication. To overcome the drawbacks of analog vehicle driving interface, this paper presents
the development and implementation of a digital driving system for a semi-autonomous vehicle to improve the
driver-vehicle interface. This offers increased flexibility and expandability. This system uses sensors to
measure temperature, distance from the other car, presence of alcohol in car, position monitoring, theft
monitoring and etc., and sends a warning signal to the driver if any of the parameter goes out of range to avoid
accidents. In addition to this if accident occurs in any remote area then using vibration sensor, accident is
detected and SMS is send immediately using GSM and preventing him from potentially getting into a serious
problems.
As the rising of transportation system design, so many data logger design was developed for safety. In our country, there are
many accidents on highways. Both driver’s faults and road construction cause accidents. To reduce these condition some safety
system such as obstacle detection system, vehicle declination alarm system, temperature and smoke level display unit,
signboard warning on road sides should be used for both driver and passengers. In addition data logger system for whole
vehicle must be equipped for safety. With the implementation of PIC microcontroller as an Embedded device, this logger
design was constructed with many sensors and C# service-based database. Using Arduino boards, vehicle detection sensing
circuit, Check point radio signal sensing circuit for dangerous road sector, hall-effect magnetic wheel revolution sensing circuit
were designed to be connected with main PIC microcontroller and Personal Computer. Real time result was displayed on C#
Graphical User Interface and Vehicle data log could be easily exported to Microsoft Excel report.
Keywords -Arduino, alarm and alert system,C# service-based database, PC based control system, Vehicle data
logger.
The main objective of our project is to provide an optimum solution to the traffic hazards and the road accidents. According to this project when a vehicle meets with an accident, immediately vibration sensor will detect the signal and sends it to ARM controller. Microcontroller sends the alert message through the GSM MODEM including the location to police control room or a rescue team. So the police can immediately trace the location through the GPS MODEM after receiving the information.
Due to the heavy traffic in the road many people are suffering. Even though there is traffic signal available at various places it is not easy to control the crowd. In order to avoid traffic problem heavily on the road, we designed and developed a system so called as traffic controller with wireless control for ambulance and VIP vehicles. In this paper, we proposed an Implementing Intelligent Traffic Control for Congestion, Ambulance clearance, and Stolen Vehicle Detection. This system was implemented based on present criteria that tracking three conditions in those one is heavy traffic control and another one is making a root of emergency vehicle like ambulance and VIP vehicle. In this paper we are going to implement a sensor network work which is used to detect the traffic density and also use RFID reader and tags. We use AVR system-on-chip to read the RFID tags attached to the vehicles. It counts number of vehicles that passes on a particular path during a specified duration using infrared sensor. If the RFID tag read belongs to the stolen vehicles. GSM SIM900 used for message sending towards the police control room. In addition, when an ambulance or some VIP vehicle if approach the junction, it will communicate the traffic controller in the junction to turn on the green light in the path.
This paper proposes smart monitoring of automobiles using IoT, which has the same functionality of conventional scanner-automobile diagnostic device. It consists of a Raspberry pi, Arduino Uno board, Web page for the service centre and also various sensors. The sensors attached in the car are connected with the Arduino board and the output is given to the raspberry pi and the Ethernet field uploads these readings to the server. If any variation in the readings, the server will send SMS to the users mobile to inform about the particular condition. And also it is possible to check the current status of the vehicle and there is special facility called emergency request that is requested by the user to inform about the accident or sudden breakdown to the service centre. It also has an obstacle sensor to sense any obstacles within a particular distance. Dust sensor fixed inside the car monitors the dust content, which can cause health problems to passengers. If there occurs any such scenarios, an SMS will be sent to the user. The vehicle will not get started if the seat belt is not worn by the driver. Detection of fire or water can result to automatic unlocking of the seat belts.
Implementing intelligent traffic control system for congestion control, ambula...LeMeniz Infotech
Implementing Intelligent Traffic Control System for Congestion Control, Ambulance Clearance, and Stolen Vehicle Detection
This paper presents an intelligent traffic control system to pass emergency vehicles smoothly. Each individual vehicle is equipped with special radio frequency identification (RFID) tag (placed at a strategic location), which makes it impossible to remove or destroy. We use RFID reader, NSK EDK-125–TTL, and PIC16F877A system-on-chip to read the RFID tags attached to the vehicle. It counts number of vehicles that passes on a particular path during a specified duration. It also determines the network congestion, and hence the green light duration for that path. If the RFID-tag-read belongs to the stolen vehicle, then a message is sent using GSM SIM300 to the police control room. In addition, when an ambulance is approaching the junction, it will communicate to the traffic controller in the junction to turn ON the green light. This module uses ZigBee modules on CC2500 and PIC16F877A system-on-chip for wireless communications between the ambulance and traffic controller.
Web : http://www.lemenizinfotech.com
web : http://www.lemenizinfotech.com/embedded-ieee-projects-2016-2017/
Web : http://ieeemaster.com
Web : http://ieeemaster.com/embedded-ieee-projects-2016-2017/
Address: 36, 100 Feet Road(Near Indira Gandhi Statue), Natesan Nagar, Pondicherry-605 005
Contact numbers: +91 95663 55386, 99625 88976 (0413) 420 5444
Mail : projects@lemenizinfotech.com
Mobile : 9566355386 / 9962588976
Unifying the Global Positioning system technology this article d esigns and realizes one kind of embedded wireless system named intelligent vehicle control for criti cal remote location application using microcontroller from the hardware and software. In terms of th e hardware completed the design and connection of embedded system,GPS module,obstacle testing module,different parameter monitoring sensor modules and the GSM module. The system can achieve the purpose of long distance real time monitoring and control of vehicle. The executive results of laboratory tests show that the system fulfils real time control and functional parameter monitoring of vehicle. In our pr oposed security system we are adding new features in addition to engine immobilizer and alarm. One of the important features supported by our system is to alert the owner by sending an SMS about the thef t attempt,using GSM Technology. The system is compatible with all brands of the vehicle. F or the worst case scenario Redundancy is maintained to make the system reliable.
Due to the heavy traffic in the road many people are suffering. Even though there is traffic signal available at various places it is not easy to control the crowd. In order to avoid traffic problem heavily on the road, we designed and developed a system so called as traffic controller with wireless control for ambulance and VIP vehicles. In this paper, we proposed an Implementing Intelligent Traffic Control for Congestion, Ambulance clearance, and Stolen Vehicle Detection. This system was implemented based on present criteria that tracking three conditions in those one is heavy traffic control and another one is making a root of emergency vehicle like ambulance and VIP vehicle. In this paper we are going to implement a sensor network work which is used to detect the traffic density and also use RFID reader and tags. We use AVR system-on-chip to read the RFID tags attached to the vehicles. It counts number of vehicles that passes on a particular path during a specified duration using infrared sensor. If the RFID tag read belongs to the stolen vehicles. GSM SIM900 used for message sending towards the police control room. In addition, when an ambulance or some VIP vehicle if approach the junction, it will communicate the traffic controller in the junction to turn on the green light in the path.
This paper proposes smart monitoring of automobiles using IoT, which has the same functionality of conventional scanner-automobile diagnostic device. It consists of a Raspberry pi, Arduino Uno board, Web page for the service centre and also various sensors. The sensors attached in the car are connected with the Arduino board and the output is given to the raspberry pi and the Ethernet field uploads these readings to the server. If any variation in the readings, the server will send SMS to the users mobile to inform about the particular condition. And also it is possible to check the current status of the vehicle and there is special facility called emergency request that is requested by the user to inform about the accident or sudden breakdown to the service centre. It also has an obstacle sensor to sense any obstacles within a particular distance. Dust sensor fixed inside the car monitors the dust content, which can cause health problems to passengers. If there occurs any such scenarios, an SMS will be sent to the user. The vehicle will not get started if the seat belt is not worn by the driver. Detection of fire or water can result to automatic unlocking of the seat belts.
Implementing intelligent traffic control system for congestion control, ambula...LeMeniz Infotech
Implementing Intelligent Traffic Control System for Congestion Control, Ambulance Clearance, and Stolen Vehicle Detection
This paper presents an intelligent traffic control system to pass emergency vehicles smoothly. Each individual vehicle is equipped with special radio frequency identification (RFID) tag (placed at a strategic location), which makes it impossible to remove or destroy. We use RFID reader, NSK EDK-125–TTL, and PIC16F877A system-on-chip to read the RFID tags attached to the vehicle. It counts number of vehicles that passes on a particular path during a specified duration. It also determines the network congestion, and hence the green light duration for that path. If the RFID-tag-read belongs to the stolen vehicle, then a message is sent using GSM SIM300 to the police control room. In addition, when an ambulance is approaching the junction, it will communicate to the traffic controller in the junction to turn ON the green light. This module uses ZigBee modules on CC2500 and PIC16F877A system-on-chip for wireless communications between the ambulance and traffic controller.
Web : http://www.lemenizinfotech.com
web : http://www.lemenizinfotech.com/embedded-ieee-projects-2016-2017/
Web : http://ieeemaster.com
Web : http://ieeemaster.com/embedded-ieee-projects-2016-2017/
Address: 36, 100 Feet Road(Near Indira Gandhi Statue), Natesan Nagar, Pondicherry-605 005
Contact numbers: +91 95663 55386, 99625 88976 (0413) 420 5444
Mail : projects@lemenizinfotech.com
Mobile : 9566355386 / 9962588976
Unifying the Global Positioning system technology this article d esigns and realizes one kind of embedded wireless system named intelligent vehicle control for criti cal remote location application using microcontroller from the hardware and software. In terms of th e hardware completed the design and connection of embedded system,GPS module,obstacle testing module,different parameter monitoring sensor modules and the GSM module. The system can achieve the purpose of long distance real time monitoring and control of vehicle. The executive results of laboratory tests show that the system fulfils real time control and functional parameter monitoring of vehicle. In our pr oposed security system we are adding new features in addition to engine immobilizer and alarm. One of the important features supported by our system is to alert the owner by sending an SMS about the thef t attempt,using GSM Technology. The system is compatible with all brands of the vehicle. F or the worst case scenario Redundancy is maintained to make the system reliable.
Due to increasing technology Automotive Electronics sector is now becoming more in demand. Most of luxurious vehicles consist of automatic controls of different parameters present in the car surrounding. As more and more latest applications are available on vehicle information system, therefore connection between the vehicle bus network and information system is now becoming a trend. Basically in automobile industries for communication, the CAN protocol is used. The proposed system presents the development and implementation of the digital driving system for a semi-autonomous vehicle for improving the driver vehicle interface and CAN provide technological development for future applications in vehicle’s information system. The proposed system is use to monitor driver’s behaviour, Drowsiness and Alcohol with the help of sensors. System contains controller block designed using ARM Cortex M-3, alcohol and sensors, CAN controller, GPS and GSM modules.
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...Amil Baba Dawood bangali
Contact with Dawood Bhai Just call on +92322-6382012 and we'll help you. We'll solve all your problems within 12 to 24 hours and with 101% guarantee and with astrology systematic. If you want to take any personal or professional advice then also you can call us on +92322-6382012 , ONLINE LOVE PROBLEM & Other all types of Daily Life Problem's.Then CALL or WHATSAPP us on +92322-6382012 and Get all these problems solutions here by Amil Baba DAWOOD BANGALI
#vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore#blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #blackmagicforlove #blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #Amilbabainuk #amilbabainspain #amilbabaindubai #Amilbabainnorway #amilbabainkrachi #amilbabainlahore #amilbabaingujranwalan #amilbabainislamabad
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
CFD Simulation of By-pass Flow in a HRSG module by R&R Consult.pptxR&R Consult
CFD analysis is incredibly effective at solving mysteries and improving the performance of complex systems!
Here's a great example: At a large natural gas-fired power plant, where they use waste heat to generate steam and energy, they were puzzled that their boiler wasn't producing as much steam as expected.
R&R and Tetra Engineering Group Inc. were asked to solve the issue with reduced steam production.
An inspection had shown that a significant amount of hot flue gas was bypassing the boiler tubes, where the heat was supposed to be transferred.
R&R Consult conducted a CFD analysis, which revealed that 6.3% of the flue gas was bypassing the boiler tubes without transferring heat. The analysis also showed that the flue gas was instead being directed along the sides of the boiler and between the modules that were supposed to capture the heat. This was the cause of the reduced performance.
Based on our results, Tetra Engineering installed covering plates to reduce the bypass flow. This improved the boiler's performance and increased electricity production.
It is always satisfying when we can help solve complex challenges like this. Do your systems also need a check-up or optimization? Give us a call!
Work done in cooperation with James Malloy and David Moelling from Tetra Engineering.
More examples of our work https://www.r-r-consult.dk/en/cases-en/