This document presents a study on the seismic analysis of reinforced concrete framed structures located on varying slope angles, with and without shear walls. 12 models of a 10-story building were developed with slope angles of 0°, 11.25°, 22.5°, and 45° to analyze seismic performance. The models were analyzed using ETABS software for equivalent static and response spectrum analysis according to Indian seismic codes. Results for parameters like base shear, story shear, story displacement, and story drift were obtained and compared for models with shear walls at corners, corners and edges, and without shear walls. In general, models with shear walls performed better in reducing seismic demands.
Cyclic Load Test on Beam-Column Behavior of Portal Frame Strengthening by Mic...Md. Sajjak Hosain
I am Md. Sajjak Hosain. This is my undergraduate thesis program for retrofitting of existing structure with local material available in Bangladesh. This thesis highlights the behavior of RCC structure after and before strengthening.
Cyclic Load Test on Beam-Column Behavior of Portal Frame Strengthening by Mic...Md. Sajjak Hosain
I am Md. Sajjak Hosain. This is my undergraduate thesis program for retrofitting of existing structure with local material available in Bangladesh. This thesis highlights the behavior of RCC structure after and before strengthening.
Seismic Vulnerability Assessment of Steel Moment Resisting Frame due to Infil...IDES Editor
Steel moment resisting frame with open first storey
(soft storey) is known to perform well compared with the RC
frames during strong earthquake shaking. The presence of
masonry infill wall influences the overall behavior of the
structure when subjected to lateral forces, when masonry infill
are considered to interact with their surrounding frames the
lateral stiffness and lateral load carrying capacity of structure
largely increase. In this paper, the seismic vulnerability of
building with soft storey is shown with an example of G+10
three dimensional (3D) steel frame. The open first storey is
an important functional requirement of almost all the urban
multi-storey buildings, and hence, cannot be eliminated.
Hence some special measures need to be adopted for this
specific situation. The under-lying principle of any solution
to this problem is in increasing the stiffness’s of the first
storey such that the first storey stiffness is at least 50% as
stiff as the second storey, i.e., soft first storeys are to be avoided,
and providing adequate lateral strength in the first storey. In
this paper, stiffness balancing is proposed between the first
and second storey of a steel moment resisting frame building
with open first storey and brick infills as described in models.
A simple example building is analyzed by modeling it with
nine different methods. The stiffness effect on the first storey
is demonstrated through the lateral displacement profile of
the building.
Behavioural Study of RC Flat Plate Multi-Storey Building Persuaded By Stiffne...IJERA Editor
With a very swift development in urban areas the framed structures which are infilled by brick masonry or
concrete blocks are widely used as partition walls and also exterior walls. Masonry infill walls are common
element in structural system which modifies the conduction of building under the lateral load. These structures
resist the moderate earthquakes and accomplish well in such a prime manner that even if they have no load
bearing function. Evidently, during the time of resolution of such a multi-storey structure, the infilled frame is
considered as bare frame, because IS codes do not provide any guide lines for the analysis and design of RC
frames with infill wall. This paper addresses the numerical study of G+10 RC flat plate framed building with
different cases i.e, soft story at ground level (Basement), with soft story at 5th floor level, without soft storey and
bare frame building by using ETABS as soft computing tool. All these cases are analyzed for equivalent static
method and Response spectrum method. By this, dynamic properties are evaluated and according to the results
obtained conclusions are drawn
Seismic Vulnerability Assessment of Steel Moment Resisting Frame due to Infil...IDES Editor
Steel moment resisting frame with open first storey
(soft storey) is known to perform well compared with the RC
frames during strong earthquake shaking. The presence of
masonry infill wall influences the overall behavior of the
structure when subjected to lateral forces, when masonry infill
are considered to interact with their surrounding frames the
lateral stiffness and lateral load carrying capacity of structure
largely increase. In this paper, the seismic vulnerability of
building with soft storey is shown with an example of G+10
three dimensional (3D) steel frame. The open first storey is
an important functional requirement of almost all the urban
multi-storey buildings, and hence, cannot be eliminated.
Hence some special measures need to be adopted for this
specific situation. The under-lying principle of any solution
to this problem is in increasing the stiffness’s of the first
storey such that the first storey stiffness is at least 50% as
stiff as the second storey, i.e., soft first storeys are to be avoided,
and providing adequate lateral strength in the first storey. In
this paper, stiffness balancing is proposed between the first
and second storey of a steel moment resisting frame building
with open first storey and brick infills as described in models.
A simple example building is analyzed by modeling it with
nine different methods. The stiffness effect on the first storey
is demonstrated through the lateral displacement profile of
the building.
Behavioural Study of RC Flat Plate Multi-Storey Building Persuaded By Stiffne...IJERA Editor
With a very swift development in urban areas the framed structures which are infilled by brick masonry or
concrete blocks are widely used as partition walls and also exterior walls. Masonry infill walls are common
element in structural system which modifies the conduction of building under the lateral load. These structures
resist the moderate earthquakes and accomplish well in such a prime manner that even if they have no load
bearing function. Evidently, during the time of resolution of such a multi-storey structure, the infilled frame is
considered as bare frame, because IS codes do not provide any guide lines for the analysis and design of RC
frames with infill wall. This paper addresses the numerical study of G+10 RC flat plate framed building with
different cases i.e, soft story at ground level (Basement), with soft story at 5th floor level, without soft storey and
bare frame building by using ETABS as soft computing tool. All these cases are analyzed for equivalent static
method and Response spectrum method. By this, dynamic properties are evaluated and according to the results
obtained conclusions are drawn
The optimum location of shear wall in high rise r.c bulidings under lateral l...eSAT Journals
Abstract Shear walls are the structural elements of the horizontal force resisting system .shear walls have high influence stiffness and strength and provided to resist gravity loads as well as lateral loads caused by seismic and wind. So many literatures are available to analyze and design of shear wall. However the optimum location and its effects in high rise r.c.buildings is not much discussed in any literatures. In this paper the main aim is to find the effective, efficient, and optimum location of shear walls in high rise irregular R.C building. In this present study the optimum location of shear wall has been investigated with the help of three different models. Model 1 is bare frame structural system and other two models are dual type structural system with central core wall and corner shear wall. An earthquake load is calculated as per IS 1893(PART-1)-2002 and applied to (G+20) storey R.C building in zone-2 and zone-5. The analysis is performed using ETABS 9.7.4 Software package. Keywords: Shear wall, Irregular building, ETABS, analysis of structure, High rise building
Similar to IRJET- A Study on Seismic Analysis of RC Framed Structures on Varying Slope Angles with & without Shear Walls (20)
NUMERICAL SIMULATIONS OF HEAT AND MASS TRANSFER IN CONDENSING HEAT EXCHANGERS...ssuser7dcef0
Power plants release a large amount of water vapor into the
atmosphere through the stack. The flue gas can be a potential
source for obtaining much needed cooling water for a power
plant. If a power plant could recover and reuse a portion of this
moisture, it could reduce its total cooling water intake
requirement. One of the most practical way to recover water
from flue gas is to use a condensing heat exchanger. The power
plant could also recover latent heat due to condensation as well
as sensible heat due to lowering the flue gas exit temperature.
Additionally, harmful acids released from the stack can be
reduced in a condensing heat exchanger by acid condensation. reduced in a condensing heat exchanger by acid condensation.
Condensation of vapors in flue gas is a complicated
phenomenon since heat and mass transfer of water vapor and
various acids simultaneously occur in the presence of noncondensable
gases such as nitrogen and oxygen. Design of a
condenser depends on the knowledge and understanding of the
heat and mass transfer processes. A computer program for
numerical simulations of water (H2O) and sulfuric acid (H2SO4)
condensation in a flue gas condensing heat exchanger was
developed using MATLAB. Governing equations based on
mass and energy balances for the system were derived to
predict variables such as flue gas exit temperature, cooling
water outlet temperature, mole fraction and condensation rates
of water and sulfuric acid vapors. The equations were solved
using an iterative solution technique with calculations of heat
and mass transfer coefficients and physical properties.
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
6th International Conference on Machine Learning & Applications (CMLA 2024)ClaraZara1
6th International Conference on Machine Learning & Applications (CMLA 2024) will provide an excellent international forum for sharing knowledge and results in theory, methodology and applications of on Machine Learning & Applications.
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
HEAP SORT ILLUSTRATED WITH HEAPIFY, BUILD HEAP FOR DYNAMIC ARRAYS.
Heap sort is a comparison-based sorting technique based on Binary Heap data structure. It is similar to the selection sort where we first find the minimum element and place the minimum element at the beginning. Repeat the same process for the remaining elements.
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...Amil Baba Dawood bangali
Contact with Dawood Bhai Just call on +92322-6382012 and we'll help you. We'll solve all your problems within 12 to 24 hours and with 101% guarantee and with astrology systematic. If you want to take any personal or professional advice then also you can call us on +92322-6382012 , ONLINE LOVE PROBLEM & Other all types of Daily Life Problem's.Then CALL or WHATSAPP us on +92322-6382012 and Get all these problems solutions here by Amil Baba DAWOOD BANGALI
#vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore#blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #blackmagicforlove #blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #Amilbabainuk #amilbabainspain #amilbabaindubai #Amilbabainnorway #amilbabainkrachi #amilbabainlahore #amilbabaingujranwalan #amilbabainislamabad