This document analyzes the seismic performance of buildings resting on sloping ground with different shear wall configurations using ETABS software. A 6-storey building model is analyzed on slopes of 15, 20, and 25 degrees with 8 different shear wall layouts. Results show that maximum story displacement and base shear decrease while story drift ratio decreases as more shear walls are added. Placing shear walls on all sides is most effective at reducing seismic response. As slope increases, story displacement and base shear also increase. Shear walls are most effective at reducing displacement along the slope direction. Therefore, shear walls improve seismic performance of buildings on sloping sites, and placement is important to consider slope direction.
Comparison of performance of lateral load resisting systems in multi storey f...eSAT Journals
Abstract This paper introduces the comparison between lateral load resisting systems in multi storey building. Multi storey building
composed of very special class of structure and therefore require special treatment. Hence to overcome the effects of seismic
forces, Flat slab system in which slab rests on drop or capital which is connected to column is induced with different load
resisting systems. The combined systems which is used to withstand seismic forces in this study are 1. Flat slab without lateral
load resisting system, 2. Flat slab with shear wall, 3. Flat slab with infill wall, 4. Flat slab with bracings, 5. Flat slab with shear
wall and bracings. ETABS software version is used to accomplish dynamic analysis and also building is investigated for nonlinear
static analysis in order to identify seismic demands. From the obtained results conclusions are drawn.
Keywords: Capital, Bracings, Dynamic, and Treatment etc…
Comparison of performance of lateral load resisting systems in multi storey f...eSAT Journals
Abstract This paper introduces the comparison between lateral load resisting systems in multi storey building. Multi storey building
composed of very special class of structure and therefore require special treatment. Hence to overcome the effects of seismic
forces, Flat slab system in which slab rests on drop or capital which is connected to column is induced with different load
resisting systems. The combined systems which is used to withstand seismic forces in this study are 1. Flat slab without lateral
load resisting system, 2. Flat slab with shear wall, 3. Flat slab with infill wall, 4. Flat slab with bracings, 5. Flat slab with shear
wall and bracings. ETABS software version is used to accomplish dynamic analysis and also building is investigated for nonlinear
static analysis in order to identify seismic demands. From the obtained results conclusions are drawn.
Keywords: Capital, Bracings, Dynamic, and Treatment etc…
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
CFD Simulation of By-pass Flow in a HRSG module by R&R Consult.pptxR&R Consult
CFD analysis is incredibly effective at solving mysteries and improving the performance of complex systems!
Here's a great example: At a large natural gas-fired power plant, where they use waste heat to generate steam and energy, they were puzzled that their boiler wasn't producing as much steam as expected.
R&R and Tetra Engineering Group Inc. were asked to solve the issue with reduced steam production.
An inspection had shown that a significant amount of hot flue gas was bypassing the boiler tubes, where the heat was supposed to be transferred.
R&R Consult conducted a CFD analysis, which revealed that 6.3% of the flue gas was bypassing the boiler tubes without transferring heat. The analysis also showed that the flue gas was instead being directed along the sides of the boiler and between the modules that were supposed to capture the heat. This was the cause of the reduced performance.
Based on our results, Tetra Engineering installed covering plates to reduce the bypass flow. This improved the boiler's performance and increased electricity production.
It is always satisfying when we can help solve complex challenges like this. Do your systems also need a check-up or optimization? Give us a call!
Work done in cooperation with James Malloy and David Moelling from Tetra Engineering.
More examples of our work https://www.r-r-consult.dk/en/cases-en/