In-Situ Oxidation Procedure for High and Low Temperature Shift Catalysts
•
3 likes•692 views
GBH Enterprises provides a 7-step procedure for the in-situ oxidation of high and low temperature shift catalysts prior to removal from the system. The procedure involves purging combustibles, cooling the catalyst beds, metering in air at increasing rates, and monitoring temperatures until oxidation is complete, estimated at 12 hours. The process allows for the controlled oxidation and safe discharge of the catalysts.
Report
Share
Report
Share
Download to read offline
Recommended
Low Temperature Shift Catalyst Reduction Procedure
Low Temperature Shift Catalyst Reduction Procedure
VSG-C111 as supplied contains copper oxide; it is activated for the low temperature shift duty by reducing the copper oxide component to metallic copper with hydrogen. The reaction is highly exothermic. In order to achieve maximum activity, good performance and long life, it is essential that the reduction is conducted under correctly controlled conditions. Great care must be taken to avoid thermal damage during this critical operation.
Catalyst Breakage in Reformer Tubes
Introduction
Catalyst breakage is a well known phenomena that occurs during operation and transients such as reformer trips, whether this be due to,
• Normal in service breakage,
• Breakage due to carbon formation/removal,
• Breakage due to steam condensation or carry over,
• Breakage during a trip.
The effect of catalyst breakage can be observed in a number of ways,
• Hot bands,
• Speckling and giraffe necking,
• Catalyst breakage and settling.
Theory and Operation - Secondary Reformers -
Purpose
Key to good performance
Problem Areas
Catalysts, heat shields and plant up-rates
Burner Guns
Development of High Intensity Ring Burner
Case Studies
Conclusions
(LTS) Low Temperature Shift Catalyst - Comprehensive Overview
The document discusses low temperature shift catalysts used in hydrogen production plants. It describes the purpose of low temperature shift catalysts in further converting carbon monoxide to carbon dioxide to improve hydrogen yield and remove impurities. It then covers the chemistry, typical operating conditions, factors influencing catalyst activity like temperature profile and poisons, and byproduct formation issues. The document promotes the VSG-C111/112 series as superior catalysts, highlighting their resistance to poisons like sulfur and chloride, low methanol byproduct formation, high activity, and strength properties.
(HTS) High Temperature Shift Catalyst (VSG-F101) - Comprehensiev Overview
The document discusses improvements in high temperature shift catalysts. It describes the characteristics and operational issues of traditional HTS catalysts and how the new VULCAN Series VSG-F101 catalyst has addressed these issues through modifications to its microstructure and composition. The VSG-F101 has shown improved activity, strength, and resistance to thermal and mechanical stresses during plant upsets compared to previous catalysts.
Steam Reformer Surveys - Techniques for Optimization of Primary Reformer Oper...
Introduction
Background Radiation and Temperature Measurement
Reformer Survey Inputs
Other Troubleshooting Tools
Safety
Preparation
Onsite Data Collection
TWT Survey
Observation/Troubleshooting
Modelling and Analysis
Results/Outputs
Case Studies
Conclusions
Case Study 1
Case Study 2
Case Study 3
Conclusions
Steam Reforming - Common Problems
Examination of some of the common problems that occur on steam reformers
Analyze problems associated with
Catalyst
Tubes
Reformer Design
Common Problems
- Poisoning
- Carbon formation
- Tunnel problems
- Air leaks
- Tube failures
Less common ones include
- Tunnel Port Effect
- Flue gas Mal-distribution
CATALYST PROBLEMS
- Poisoning
- Hot Bands
- Carbon Formation
- Hot Banding & Tube Appearances
- Nipped Tubes - The Domino Effect
- Catalyst Loading
- Affect of Delta P Variation
- Catalyst Settling
- Catalyst Breakage
HARDWARE PROBLEMS
- Foster Wheeler Terraced Wall
- Mal distribution
- Collapsed Tunnels
- Effect of Removing Coffins
- Undersized Fans
- Other Hardware Problems
OPERATIONAL PROBLEMS
- Flame Impingement
- After Burning
- Catalyst Milling
- Catalyst Breakage
- Catalyst Color Variation
- Bowed Tubes
- Refractory Problems
- Other Operational Problems
Feedstock Purfication in Hydrogen Plants
1. Introduction reasons for purification, types of poisons, and typical systems
2. Hydrogenation
3. Dechlorination
4. Sulfur Removal
5. Purification system start-up and shut-down
Recommended
Low Temperature Shift Catalyst Reduction Procedure
Low Temperature Shift Catalyst Reduction Procedure
VSG-C111 as supplied contains copper oxide; it is activated for the low temperature shift duty by reducing the copper oxide component to metallic copper with hydrogen. The reaction is highly exothermic. In order to achieve maximum activity, good performance and long life, it is essential that the reduction is conducted under correctly controlled conditions. Great care must be taken to avoid thermal damage during this critical operation.
Catalyst Breakage in Reformer Tubes
Introduction
Catalyst breakage is a well known phenomena that occurs during operation and transients such as reformer trips, whether this be due to,
• Normal in service breakage,
• Breakage due to carbon formation/removal,
• Breakage due to steam condensation or carry over,
• Breakage during a trip.
The effect of catalyst breakage can be observed in a number of ways,
• Hot bands,
• Speckling and giraffe necking,
• Catalyst breakage and settling.
Theory and Operation - Secondary Reformers -
Purpose
Key to good performance
Problem Areas
Catalysts, heat shields and plant up-rates
Burner Guns
Development of High Intensity Ring Burner
Case Studies
Conclusions
(LTS) Low Temperature Shift Catalyst - Comprehensive Overview
The document discusses low temperature shift catalysts used in hydrogen production plants. It describes the purpose of low temperature shift catalysts in further converting carbon monoxide to carbon dioxide to improve hydrogen yield and remove impurities. It then covers the chemistry, typical operating conditions, factors influencing catalyst activity like temperature profile and poisons, and byproduct formation issues. The document promotes the VSG-C111/112 series as superior catalysts, highlighting their resistance to poisons like sulfur and chloride, low methanol byproduct formation, high activity, and strength properties.
(HTS) High Temperature Shift Catalyst (VSG-F101) - Comprehensiev Overview
The document discusses improvements in high temperature shift catalysts. It describes the characteristics and operational issues of traditional HTS catalysts and how the new VULCAN Series VSG-F101 catalyst has addressed these issues through modifications to its microstructure and composition. The VSG-F101 has shown improved activity, strength, and resistance to thermal and mechanical stresses during plant upsets compared to previous catalysts.
Steam Reformer Surveys - Techniques for Optimization of Primary Reformer Oper...
Introduction
Background Radiation and Temperature Measurement
Reformer Survey Inputs
Other Troubleshooting Tools
Safety
Preparation
Onsite Data Collection
TWT Survey
Observation/Troubleshooting
Modelling and Analysis
Results/Outputs
Case Studies
Conclusions
Case Study 1
Case Study 2
Case Study 3
Conclusions
Steam Reforming - Common Problems
Examination of some of the common problems that occur on steam reformers
Analyze problems associated with
Catalyst
Tubes
Reformer Design
Common Problems
- Poisoning
- Carbon formation
- Tunnel problems
- Air leaks
- Tube failures
Less common ones include
- Tunnel Port Effect
- Flue gas Mal-distribution
CATALYST PROBLEMS
- Poisoning
- Hot Bands
- Carbon Formation
- Hot Banding & Tube Appearances
- Nipped Tubes - The Domino Effect
- Catalyst Loading
- Affect of Delta P Variation
- Catalyst Settling
- Catalyst Breakage
HARDWARE PROBLEMS
- Foster Wheeler Terraced Wall
- Mal distribution
- Collapsed Tunnels
- Effect of Removing Coffins
- Undersized Fans
- Other Hardware Problems
OPERATIONAL PROBLEMS
- Flame Impingement
- After Burning
- Catalyst Milling
- Catalyst Breakage
- Catalyst Color Variation
- Bowed Tubes
- Refractory Problems
- Other Operational Problems
Feedstock Purfication in Hydrogen Plants
1. Introduction reasons for purification, types of poisons, and typical systems
2. Hydrogenation
3. Dechlorination
4. Sulfur Removal
5. Purification system start-up and shut-down
Shift Conversion Catalysts - Operating Manual
Introduction High temperature shift Catalysts
Low temperature shift catalysts
Catalyst storage, handling, charging and discharging
Health and safety precautions
Reduction and start-up of high temperature shift catalysts
Operation of high temperature shift catalysts
Reduction and start-up of low temperature shift catalysts
Operation of low temperature shift catalysts
101 Things That Can Go Wrong on a Primary Reformer - Best Practices Guide
This document discusses common problems that can occur in primary reformers and associated equipment. It identifies issues that can lead to plant shutdowns or efficiency losses, grouping them under catalysts, tubes, furnace boxes, burners, flue gas ducts, headers, and refractories. Some examples discussed include carbon formation, tube overheating, flame impingement, leaks in air preheaters, combustion air maldistribution, and damage to coffins. The document provides an overview of these issues to improve plant reliability over its lifespan.
Ammonia Formation over Steam Reforming Catalysts
This document discusses ammonia (NH3) formation over steam reforming catalysts. It provides rules of thumb for NH3 formation in primary and secondary reformers, noting it is kinetically limited and does not reach equilibrium. NH3 formation is influenced by nitrogen concentration, hydrogen concentration, temperature, catalyst activity, residence time, and pressure. The document also presents theoretical rate equations and discusses how process conditions like steam:carbon ratio affect NH3 production. Graphs demonstrate the effect of temperature and pressure on NH3 production.
High Temperature Shift Catalyst Reduction Procedure
High Temperature Shift Catalyst Reduction Procedure
The catalyst, as supplied, is Fe2O3. This reduces to the active form, Fe3O4, in the presence of hydrogen when process gas is admitted to the reactor.
1. The mildly exothermic reactions are:
3 Fe2O3 + H2 ========= 2 Fe3O4 + H2O
3 Fe2O3 + CO ========= 2 Fe3O4 + CO2
Steam Reforming - Tube Design
Reformer Tube design principles
- Larsen Miller Plot
- Larsen Miller & Tube Design
- Design Margins - Stress Data Used
- Max Allowable & Design Temperature
- Tube Life
- Effect of Temperature on Life
- Material Types
HK40: 25 Cr / 20 Ni
HP Modified: 25 Cr / 35 Ni + Nb
Microalloy: 25 Cr / 35 Ni + Nb + Ti
- Alloy Developments
- Comparison of Alloys
Manufacturing Technology
- Welds
Failure mechanisms
- Failure Mechanisms - Creep
- Creep Propagation
- Common Failure Modes
- Uncommon Failure Modes
- Failure by Creep
- Creep Rupture - Cross Section
- Failure at Weld
Actions to Take if Tube Fails
- Pigtail Nipping
Inspection techniques
Classification of Problems
- Visual Examination
- Girth Measurement
- Ultrasonic Attenuation
- Radiography
Eddy Current Measurement
LOTIS Tube Inspection
LOTIS Compared to External Inspection
Theory of Carbon Formation in Steam Reforming
Theory of Carbon Formation in Steam Reforming
Contents
1 Introduction
2 Underpinning Theory
2.1 Conceptualization
2.2 Reforming Reactions
2.3 Carbon Formation Chemistry
2.3.1 Natural Gas
2.3.2 Carbon Formation for Naphtha Feeds
2.3.3 Carbon Gasification
2.4 Heat Transfer
3 Causes
3.1 Effects of Carbon Formation
3.2 Types of Carbon
4 What are the Effects of Carbon Formation?
4.1 Why does Carbon Formation Get Worse?
4.1.1 So what is the Next Step?
4.2 Consequences of Carbon Formation
4.3 Why does Carbon Form where it does?
4.3.1 Effect on Process Gas Temperature
4.4 Why does Carbon Formation Propagate Down the Tube?
4.4.1 Effect on Radiation on the Fluegas Side
4.5 Why does Carbon Formation propagate Up the Tube?
5 How do we Prevent Carbon Formation
5.1 The Role of Potash
5.2 Inclusion of Pre-reformer
5.3 Primary Reformer Catalyst Parameters
5.3.1 Activity
5.3.2 Heat Transfer
5.3.3 Increased Steam to Carbon Ratio
6 Steam Out
6.1 Why does increasing the Steam to Carbon Ratio Not Work?
6.2 Why does reducing the Feed Rate not help?
6.3 Fundamental Principles of Steam Outs
TABLES
1 Heat Transfer Coefficients in a Typical Reformer
2 Typical Catalyst Loading Options
FIGURES
1 Hot Bands
2 Conceptual Pellet
3 Naphtha Carbon Formation
4 Heat Transfer within an Reformer
5 Types of Carbon Formation
6 Effect of Carbon on Nickel Crystallites
7 Absorption of Heat
8 Comparison of "Base Case" v Carbon Forming Tube
9 Carbon Formation Vicious Circle
10 Temperature Profiles
11 Carbon Pinch Point
12 Carbon Formation
13 Effect on Process Gas Temperature
14 How does Carbon Propagate into an Unaffected Zone?
15 Movement of the Carbon Forming Region
16 Effect of Hot Bands on Radiative Heat Transfer
17 Effect of Potash on Carbon Formation
18 Application of a Pre-reformer
19 Effect of Activity on Carbon Formation
A presentation on reformer new
The document discusses different types of reformers used in ammonia plants, including pre-reformers, primary reformers, and secondary reformers. It provides details on the process, internals, catalysts, and operating conditions of each reformer type. Primary reformers are described as duplex reforming furnaces containing nickel catalyst-loaded tubes that are fired by natural gas burners to drive the endothermic reforming reactions. Key variables that impact the reforming reactions such as temperature, pressure, steam-to-carbon ratio, and catalyst activity are also summarized.
The Benefits and Disadvantages of Potash in Steam Reforming
Why do we include potash ?
What are the benefits ?
What are the disadvantages ?
Catalyst Deactivation
Carbon Deposition : Thermodynamics & Kinetics
Carbon formation margin
Reaction chemistry (Tube inlet)
Hydrocarbons undergo cracking reactions on hot surfaces at the tube inlet
Products of catalytic cracking reactions can form polymeric carbon
Start Up Procedures for Primary Reforming Catalyst
VULCAN Series VSG-Z101 Primary Reforming
Initial Catalyst Reduction
Activating (reducing) the catalyst involves changing the nickel oxide to nickel, represented by:
NiO + H2 <==========> Ni + H2O
Natural gas is typically used as the hydrogen source. When it is, the catalyst reduction and putting the reformer on-line are accompanied in the same step.
Steam Reforming - Carbon Formation
Look at two main types
Explain mechanisms
Explain prevention of cracking
Three main types
1 Carbon cracking
2 Boudouard carbon formation
3 CO reduction
STEAMING PROCEDURE FOR VULCAN STEAM REFORMING CATALYSTS
The document discusses procedures for steaming Vulcan steam reforming catalysts to recover from sulfur poisoning and carbon formation incidents. It describes maintaining steam flow at 30-40% of design levels and an outlet temperature above 780°C. Gas samples should be taken hourly to monitor CO2, CH4, H2S and SO2. Steaming is complete when CO2 levels stabilize over 2-3 samples after increasing the temperature. The process typically takes 12-24 hours to complete and closely monitors pressure drop and tube conditions. After steaming, the catalyst requires reduction before restarting hydrocarbon feed.
Calculation of Caloric Value and other Characteristic Data of Fuel Gas
Calculation of Caloric Value and other Characteristic Data of Fuel Gas
Plant Note Book Series: PNBS-0601
Steam Reforming - Practical Operations
Reaction Chemistry
Typical Reformer Configurations
Catalyst Design Criteria
Carbon Formation and Prevention
Catalyst Deactivation
Steaming Reforming Catalysts
Monitoring Reforming Catalysts
Catalyst Loading
Reduction & Start-Up
Tube Wall Temperature Measurement
Ammonia converter
This document describes the development and validation of a mathematical model for a radial flow ammonia converter. The model equations account for material and energy balances across the three catalyst beds. Comparison to plant data from Abu Qir Fertilizers Company showed good agreement between the model and actual performance. The model is useful for optimizing operating conditions, evaluating catalyst performance over time, and determining the effects of adding a fourth catalytic bed.
Catalyst Catastrophes in Syngas Production - II
Catalyst Catastrophes in Syngas Production - II
Contents
Review of incidents by reactor
Primary reforming
Secondary reforming
HTS
LTS
Methanator
Reactor loading
Support media
Some general comments on alternative actions when a plant gets into abnormal operation
PRACTICAL GUIDE TO DEVELOPING PROCESS FLOW DIAGRAMS AND PRELIMINARY ENGINEER...
PRACTICAL GUIDE TO DEVELOPING PROCESS FLOW DIAGRAMS AND PRELIMINARY ENGINEERING LINE DIAGRAMS PROCESS
CONTENTS
1 INTRODUCTION
2 DESCRIPTION OF METHODOLOGY
2.1 Philosophy of the Design Process
2.2 Outline of Methodology
2.3 Additional Aspects of Methodology
3 WORKBOOK
4 EXAMPLE: BATCH NEUTRALIZATION AND STRIPPING PROCESS
4.1 Start of Stage 1
4.2 Stage 1
4.3 Stage 2
4.3 Stage 3
5 REFERENCES
TABLES
1 DESIGN OBJECTIVES
2 OUTPUT FROM EACH STAGE
3 STEP BY STEP APPROACH
4 FUNCTION
5 OPERATION
6 FAILURES
7 STAGE 3 PROMPTS (DATA SHEET)
8 PRELIMINARY MASS BALANCE
9 PRELIMINARY EQUIPMENT LIST
10 POTENTIAL PROBLEMS
11 STAGE 2: DEVELOPMENT OF OPERATING STATES AND TRANSMISSIONS
12 POTENTIAL PROBLEMS
FIGURES
1 DESIGN PROCESS
2 DESIGN PHILOSOPHY.
3 SUMMARY OF METHODOLOGY
4 POSSIBLE OUTCOMES FROM A KEYWORD PROMPT
5 OPERATING STATES
6 OPERATING STATES/TRANSITIONS
7 EXAMPLE: OVERALL BLOCK DIAGRAM
8 EXAMPLE: “PRIMITIVE PFD”
9 EXAMPLE: STAGE 1 “WORKING DIAGRAM”.
10 EXAMPLE: MAIN OPERATING STATES AND TRANSITIONS
11 EXAMPLE: DETAILED PFD (END OF STAGE 1)
12 EXAMPLE: STAGE 2 “WORKING DIAGRAM”
13 EXAMPLE: STAGE 3 “REV 0” ELD
SRU Troubleshooting
This document discusses troubleshooting issues that can occur in sulfur recovery units (SRUs). It begins with an overview of sulfur chemistry and the Claus process for converting hydrogen sulfide to elemental sulfur. Common problems that can cause conversion losses or pressure drops are then examined, such as carbon deposits, leaks, catalyst deactivation, and improper air-to-acid gas ratios. Specific case studies are presented on troubleshooting carbon deposits from hydrocarbon contamination and identifying leaks from declining steam production and rising pressure drops. The document emphasizes the importance of continuous monitoring and preventative maintenance to address problems in SRUs before catastrophic failures occur.
Steam Reforming - A Comprehensive Review
Equilibrium, Approach & Kinetics
Carbon Laydown
Potash Doping
Catalyst Loading
Pigtail Nippers
GHR & AGHR
Secondary Reforming
Metal Dusting
Aiche 42-024-primary reformer failure- agrium
The primary reformer at Agrium's Fort Saskatchewan Nitrogen Operations experienced a massive failure following a routine startup. Almost all 260 catalyst tubes in the radiant section failed, and the air-steam preheat coil was damaged, resulting in lost production. An investigation found that additional burners were lit without checks of flame impingement or tube temperature, causing the flue gas temperature to reach over 1,000°C and melt the tubes. Over 50% of tubes failed, with molten metal solidifying in the catalyst. Kellogg Brown and Root were contracted to replace all failed components and repair the furnace to restore production as soon as possible.
Reactor and Catalyst Design
Reactor and Catalyst Design
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 CATALYST DESIGN
4.1 Equivalent Pellet Diameter
4.2 Voidage
4.3 Pellet Density
5 REACTOR DESIGN
6 CATALYST SUPPORT
6.1 Choice of Support
TABLES
1 CATALYST SUPPORT SHAPES
2 SECONDARY REFORMER SPREADSHEET
FIGURES
1 GRAPH OF EFFECTIVENESS v THIELE MODULUS
2 VARIATION OF COSTS WITH CATALYST SIZE
3 VARIATION OF COSTS WITH CATALYST BED VOIDAGE
4 VARIATION OF COSTS WITH VESSEL DIAMETER
Fugitive Emissions
0 INTRODUCTION
The four main sources of Fugitive Emissions on most plants are valves, machine seals, re-makable joints and pressure relief devices. Other possible sources include open-ended lines, sampling connections, drains and vents.
Sometimes special precautions are taken to minimize Fugitive Emissions, for example the use of bellows seal valves. However, generally no special precautions are taken and the subsequent Fugitive Emissions to atmosphere represent a significant amount of plant losses.
Regulatory requirements covering Fugitive Emissions exist in many countries and therefore a leak reduction program should be implemented. Fugitive Emissions also represent financial losses to the business as well as potential damage to the environment.
Biological Systems - A Special Case
Biological Systems: A Special Case
Up till now we have discussed various aspects of the separation and processing of fine solids without too much reference (except in the examples) to the specifics of the properties of the materials concerned. Though the material properties are the dominant influence on efficient process design and operation, it has been postulated that the necessary characteristics for process selection and optimization can be found fairly readily using easily-applicable rheological and other techniques. This underlying assumption also seems to hold good for biological suspensions; however, certain aspects of the behavior of these systems are sufficiently specialized for them to merit a separate discussion viz:
1 TYPES OF BIOLOGICAL SEPARATION
1.1 Whole-Organism Case
1.2 Part-Cell Separations
1.3 Isolation of Individual Molecular Species
2 SETTING ABOUT DEVISING AN EFFECTIVE
PROCESS FOR SEPARATION OF A BIOLOGICAL MATERIAL
2.1 Whole-Organism Case
2.1.1 Characterization of Biopolymers in the Liquor
2.1.2 Release of Internal Water
2.2 Part -Cell Separations
2.2.1 Selectivity
2.2.2 Cost
2.3 Isolation of Individual Molecular Species
3 Examples
3.1 Effective Design and Operation of a Process for Harvesting of Single Cell Protein
3.2 Harvesting of Mycoprotein for Human Consumption
3.3 Thickening of a Filamentous Organism Suspension
3.4 Separation of Poly-3-hydroxybutyrate Polymer (PHB) from Alcaligenes Eutrophus Biomass
3.5 Isolation of Organic Acid Produced by an Enzymatic Process
4 REFERENCES
Table
Figures
More Related Content
What's hot
Shift Conversion Catalysts - Operating Manual
Introduction High temperature shift Catalysts
Low temperature shift catalysts
Catalyst storage, handling, charging and discharging
Health and safety precautions
Reduction and start-up of high temperature shift catalysts
Operation of high temperature shift catalysts
Reduction and start-up of low temperature shift catalysts
Operation of low temperature shift catalysts
101 Things That Can Go Wrong on a Primary Reformer - Best Practices Guide
This document discusses common problems that can occur in primary reformers and associated equipment. It identifies issues that can lead to plant shutdowns or efficiency losses, grouping them under catalysts, tubes, furnace boxes, burners, flue gas ducts, headers, and refractories. Some examples discussed include carbon formation, tube overheating, flame impingement, leaks in air preheaters, combustion air maldistribution, and damage to coffins. The document provides an overview of these issues to improve plant reliability over its lifespan.
Ammonia Formation over Steam Reforming Catalysts
This document discusses ammonia (NH3) formation over steam reforming catalysts. It provides rules of thumb for NH3 formation in primary and secondary reformers, noting it is kinetically limited and does not reach equilibrium. NH3 formation is influenced by nitrogen concentration, hydrogen concentration, temperature, catalyst activity, residence time, and pressure. The document also presents theoretical rate equations and discusses how process conditions like steam:carbon ratio affect NH3 production. Graphs demonstrate the effect of temperature and pressure on NH3 production.
High Temperature Shift Catalyst Reduction Procedure
High Temperature Shift Catalyst Reduction Procedure
The catalyst, as supplied, is Fe2O3. This reduces to the active form, Fe3O4, in the presence of hydrogen when process gas is admitted to the reactor.
1. The mildly exothermic reactions are:
3 Fe2O3 + H2 ========= 2 Fe3O4 + H2O
3 Fe2O3 + CO ========= 2 Fe3O4 + CO2
Steam Reforming - Tube Design
Reformer Tube design principles
- Larsen Miller Plot
- Larsen Miller & Tube Design
- Design Margins - Stress Data Used
- Max Allowable & Design Temperature
- Tube Life
- Effect of Temperature on Life
- Material Types
HK40: 25 Cr / 20 Ni
HP Modified: 25 Cr / 35 Ni + Nb
Microalloy: 25 Cr / 35 Ni + Nb + Ti
- Alloy Developments
- Comparison of Alloys
Manufacturing Technology
- Welds
Failure mechanisms
- Failure Mechanisms - Creep
- Creep Propagation
- Common Failure Modes
- Uncommon Failure Modes
- Failure by Creep
- Creep Rupture - Cross Section
- Failure at Weld
Actions to Take if Tube Fails
- Pigtail Nipping
Inspection techniques
Classification of Problems
- Visual Examination
- Girth Measurement
- Ultrasonic Attenuation
- Radiography
Eddy Current Measurement
LOTIS Tube Inspection
LOTIS Compared to External Inspection
Theory of Carbon Formation in Steam Reforming
Theory of Carbon Formation in Steam Reforming
Contents
1 Introduction
2 Underpinning Theory
2.1 Conceptualization
2.2 Reforming Reactions
2.3 Carbon Formation Chemistry
2.3.1 Natural Gas
2.3.2 Carbon Formation for Naphtha Feeds
2.3.3 Carbon Gasification
2.4 Heat Transfer
3 Causes
3.1 Effects of Carbon Formation
3.2 Types of Carbon
4 What are the Effects of Carbon Formation?
4.1 Why does Carbon Formation Get Worse?
4.1.1 So what is the Next Step?
4.2 Consequences of Carbon Formation
4.3 Why does Carbon Form where it does?
4.3.1 Effect on Process Gas Temperature
4.4 Why does Carbon Formation Propagate Down the Tube?
4.4.1 Effect on Radiation on the Fluegas Side
4.5 Why does Carbon Formation propagate Up the Tube?
5 How do we Prevent Carbon Formation
5.1 The Role of Potash
5.2 Inclusion of Pre-reformer
5.3 Primary Reformer Catalyst Parameters
5.3.1 Activity
5.3.2 Heat Transfer
5.3.3 Increased Steam to Carbon Ratio
6 Steam Out
6.1 Why does increasing the Steam to Carbon Ratio Not Work?
6.2 Why does reducing the Feed Rate not help?
6.3 Fundamental Principles of Steam Outs
TABLES
1 Heat Transfer Coefficients in a Typical Reformer
2 Typical Catalyst Loading Options
FIGURES
1 Hot Bands
2 Conceptual Pellet
3 Naphtha Carbon Formation
4 Heat Transfer within an Reformer
5 Types of Carbon Formation
6 Effect of Carbon on Nickel Crystallites
7 Absorption of Heat
8 Comparison of "Base Case" v Carbon Forming Tube
9 Carbon Formation Vicious Circle
10 Temperature Profiles
11 Carbon Pinch Point
12 Carbon Formation
13 Effect on Process Gas Temperature
14 How does Carbon Propagate into an Unaffected Zone?
15 Movement of the Carbon Forming Region
16 Effect of Hot Bands on Radiative Heat Transfer
17 Effect of Potash on Carbon Formation
18 Application of a Pre-reformer
19 Effect of Activity on Carbon Formation
A presentation on reformer new
The document discusses different types of reformers used in ammonia plants, including pre-reformers, primary reformers, and secondary reformers. It provides details on the process, internals, catalysts, and operating conditions of each reformer type. Primary reformers are described as duplex reforming furnaces containing nickel catalyst-loaded tubes that are fired by natural gas burners to drive the endothermic reforming reactions. Key variables that impact the reforming reactions such as temperature, pressure, steam-to-carbon ratio, and catalyst activity are also summarized.
The Benefits and Disadvantages of Potash in Steam Reforming
Why do we include potash ?
What are the benefits ?
What are the disadvantages ?
Catalyst Deactivation
Carbon Deposition : Thermodynamics & Kinetics
Carbon formation margin
Reaction chemistry (Tube inlet)
Hydrocarbons undergo cracking reactions on hot surfaces at the tube inlet
Products of catalytic cracking reactions can form polymeric carbon
Start Up Procedures for Primary Reforming Catalyst
VULCAN Series VSG-Z101 Primary Reforming
Initial Catalyst Reduction
Activating (reducing) the catalyst involves changing the nickel oxide to nickel, represented by:
NiO + H2 <==========> Ni + H2O
Natural gas is typically used as the hydrogen source. When it is, the catalyst reduction and putting the reformer on-line are accompanied in the same step.
Steam Reforming - Carbon Formation
Look at two main types
Explain mechanisms
Explain prevention of cracking
Three main types
1 Carbon cracking
2 Boudouard carbon formation
3 CO reduction
STEAMING PROCEDURE FOR VULCAN STEAM REFORMING CATALYSTS
The document discusses procedures for steaming Vulcan steam reforming catalysts to recover from sulfur poisoning and carbon formation incidents. It describes maintaining steam flow at 30-40% of design levels and an outlet temperature above 780°C. Gas samples should be taken hourly to monitor CO2, CH4, H2S and SO2. Steaming is complete when CO2 levels stabilize over 2-3 samples after increasing the temperature. The process typically takes 12-24 hours to complete and closely monitors pressure drop and tube conditions. After steaming, the catalyst requires reduction before restarting hydrocarbon feed.
Calculation of Caloric Value and other Characteristic Data of Fuel Gas
Calculation of Caloric Value and other Characteristic Data of Fuel Gas
Plant Note Book Series: PNBS-0601
Steam Reforming - Practical Operations
Reaction Chemistry
Typical Reformer Configurations
Catalyst Design Criteria
Carbon Formation and Prevention
Catalyst Deactivation
Steaming Reforming Catalysts
Monitoring Reforming Catalysts
Catalyst Loading
Reduction & Start-Up
Tube Wall Temperature Measurement
Ammonia converter
This document describes the development and validation of a mathematical model for a radial flow ammonia converter. The model equations account for material and energy balances across the three catalyst beds. Comparison to plant data from Abu Qir Fertilizers Company showed good agreement between the model and actual performance. The model is useful for optimizing operating conditions, evaluating catalyst performance over time, and determining the effects of adding a fourth catalytic bed.
Catalyst Catastrophes in Syngas Production - II
Catalyst Catastrophes in Syngas Production - II
Contents
Review of incidents by reactor
Primary reforming
Secondary reforming
HTS
LTS
Methanator
Reactor loading
Support media
Some general comments on alternative actions when a plant gets into abnormal operation
PRACTICAL GUIDE TO DEVELOPING PROCESS FLOW DIAGRAMS AND PRELIMINARY ENGINEER...
PRACTICAL GUIDE TO DEVELOPING PROCESS FLOW DIAGRAMS AND PRELIMINARY ENGINEERING LINE DIAGRAMS PROCESS
CONTENTS
1 INTRODUCTION
2 DESCRIPTION OF METHODOLOGY
2.1 Philosophy of the Design Process
2.2 Outline of Methodology
2.3 Additional Aspects of Methodology
3 WORKBOOK
4 EXAMPLE: BATCH NEUTRALIZATION AND STRIPPING PROCESS
4.1 Start of Stage 1
4.2 Stage 1
4.3 Stage 2
4.3 Stage 3
5 REFERENCES
TABLES
1 DESIGN OBJECTIVES
2 OUTPUT FROM EACH STAGE
3 STEP BY STEP APPROACH
4 FUNCTION
5 OPERATION
6 FAILURES
7 STAGE 3 PROMPTS (DATA SHEET)
8 PRELIMINARY MASS BALANCE
9 PRELIMINARY EQUIPMENT LIST
10 POTENTIAL PROBLEMS
11 STAGE 2: DEVELOPMENT OF OPERATING STATES AND TRANSMISSIONS
12 POTENTIAL PROBLEMS
FIGURES
1 DESIGN PROCESS
2 DESIGN PHILOSOPHY.
3 SUMMARY OF METHODOLOGY
4 POSSIBLE OUTCOMES FROM A KEYWORD PROMPT
5 OPERATING STATES
6 OPERATING STATES/TRANSITIONS
7 EXAMPLE: OVERALL BLOCK DIAGRAM
8 EXAMPLE: “PRIMITIVE PFD”
9 EXAMPLE: STAGE 1 “WORKING DIAGRAM”.
10 EXAMPLE: MAIN OPERATING STATES AND TRANSITIONS
11 EXAMPLE: DETAILED PFD (END OF STAGE 1)
12 EXAMPLE: STAGE 2 “WORKING DIAGRAM”
13 EXAMPLE: STAGE 3 “REV 0” ELD
SRU Troubleshooting
This document discusses troubleshooting issues that can occur in sulfur recovery units (SRUs). It begins with an overview of sulfur chemistry and the Claus process for converting hydrogen sulfide to elemental sulfur. Common problems that can cause conversion losses or pressure drops are then examined, such as carbon deposits, leaks, catalyst deactivation, and improper air-to-acid gas ratios. Specific case studies are presented on troubleshooting carbon deposits from hydrocarbon contamination and identifying leaks from declining steam production and rising pressure drops. The document emphasizes the importance of continuous monitoring and preventative maintenance to address problems in SRUs before catastrophic failures occur.
Steam Reforming - A Comprehensive Review
Equilibrium, Approach & Kinetics
Carbon Laydown
Potash Doping
Catalyst Loading
Pigtail Nippers
GHR & AGHR
Secondary Reforming
Metal Dusting
Aiche 42-024-primary reformer failure- agrium
The primary reformer at Agrium's Fort Saskatchewan Nitrogen Operations experienced a massive failure following a routine startup. Almost all 260 catalyst tubes in the radiant section failed, and the air-steam preheat coil was damaged, resulting in lost production. An investigation found that additional burners were lit without checks of flame impingement or tube temperature, causing the flue gas temperature to reach over 1,000°C and melt the tubes. Over 50% of tubes failed, with molten metal solidifying in the catalyst. Kellogg Brown and Root were contracted to replace all failed components and repair the furnace to restore production as soon as possible.
Reactor and Catalyst Design
Reactor and Catalyst Design
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 CATALYST DESIGN
4.1 Equivalent Pellet Diameter
4.2 Voidage
4.3 Pellet Density
5 REACTOR DESIGN
6 CATALYST SUPPORT
6.1 Choice of Support
TABLES
1 CATALYST SUPPORT SHAPES
2 SECONDARY REFORMER SPREADSHEET
FIGURES
1 GRAPH OF EFFECTIVENESS v THIELE MODULUS
2 VARIATION OF COSTS WITH CATALYST SIZE
3 VARIATION OF COSTS WITH CATALYST BED VOIDAGE
4 VARIATION OF COSTS WITH VESSEL DIAMETER
What's hot (20)
101 Things That Can Go Wrong on a Primary Reformer - Best Practices Guide
101 Things That Can Go Wrong on a Primary Reformer - Best Practices Guide
High Temperature Shift Catalyst Reduction Procedure
High Temperature Shift Catalyst Reduction Procedure
The Benefits and Disadvantages of Potash in Steam Reforming
The Benefits and Disadvantages of Potash in Steam Reforming
Start Up Procedures for Primary Reforming Catalyst
Start Up Procedures for Primary Reforming Catalyst
STEAMING PROCEDURE FOR VULCAN STEAM REFORMING CATALYSTS
STEAMING PROCEDURE FOR VULCAN STEAM REFORMING CATALYSTS
Calculation of Caloric Value and other Characteristic Data of Fuel Gas
Calculation of Caloric Value and other Characteristic Data of Fuel Gas
PRACTICAL GUIDE TO DEVELOPING PROCESS FLOW DIAGRAMS AND PRELIMINARY ENGINEER...
PRACTICAL GUIDE TO DEVELOPING PROCESS FLOW DIAGRAMS AND PRELIMINARY ENGINEER...
Viewers also liked
Fugitive Emissions
0 INTRODUCTION
The four main sources of Fugitive Emissions on most plants are valves, machine seals, re-makable joints and pressure relief devices. Other possible sources include open-ended lines, sampling connections, drains and vents.
Sometimes special precautions are taken to minimize Fugitive Emissions, for example the use of bellows seal valves. However, generally no special precautions are taken and the subsequent Fugitive Emissions to atmosphere represent a significant amount of plant losses.
Regulatory requirements covering Fugitive Emissions exist in many countries and therefore a leak reduction program should be implemented. Fugitive Emissions also represent financial losses to the business as well as potential damage to the environment.
Biological Systems - A Special Case
Biological Systems: A Special Case
Up till now we have discussed various aspects of the separation and processing of fine solids without too much reference (except in the examples) to the specifics of the properties of the materials concerned. Though the material properties are the dominant influence on efficient process design and operation, it has been postulated that the necessary characteristics for process selection and optimization can be found fairly readily using easily-applicable rheological and other techniques. This underlying assumption also seems to hold good for biological suspensions; however, certain aspects of the behavior of these systems are sufficiently specialized for them to merit a separate discussion viz:
1 TYPES OF BIOLOGICAL SEPARATION
1.1 Whole-Organism Case
1.2 Part-Cell Separations
1.3 Isolation of Individual Molecular Species
2 SETTING ABOUT DEVISING AN EFFECTIVE
PROCESS FOR SEPARATION OF A BIOLOGICAL MATERIAL
2.1 Whole-Organism Case
2.1.1 Characterization of Biopolymers in the Liquor
2.1.2 Release of Internal Water
2.2 Part -Cell Separations
2.2.1 Selectivity
2.2.2 Cost
2.3 Isolation of Individual Molecular Species
3 Examples
3.1 Effective Design and Operation of a Process for Harvesting of Single Cell Protein
3.2 Harvesting of Mycoprotein for Human Consumption
3.3 Thickening of a Filamentous Organism Suspension
3.4 Separation of Poly-3-hydroxybutyrate Polymer (PHB) from Alcaligenes Eutrophus Biomass
3.5 Isolation of Organic Acid Produced by an Enzymatic Process
4 REFERENCES
Table
Figures
Determination of Argon in Ammonia Plant Process Gas Streams by Gas Chromatogr...
Determination of Argon in Ammonia Plant Process Gas Streams by Gas Chromatography
SCOPE AND FIELD OF APPLICATION
This document is a method for the determination of argon in process gas streams in the range 0-10% v/v.
Process Synthesis
Process Synthesis
INTRODUCTION
1 A SUGGESTED GENERAL APPROACH
2 EXAMPLES OF PROCESS SELECTION
2.1 Harvesting and Thickening of Single Cell Protein
2.2 Dewatering of a Specialty Latex
3 REFERENCES
TABLES
1 THE ADVANTAGES AND DISADVANTAGES OF DIFFERENT RANGE OF PH FOR “PROTEIN” ORGANISM FLOCCULATION
2 THE ADVANTAGES AND DISADVANTAGES OF VARYING EXTENTS OF CELL BREAKAGES
3 PREDICTED AND OBSERVED FILTER CAKE SOLIDS CONTENTS FOR THE VARIOUS LATICES AFTER COAGULATION
FIGURES
1 THE “PROTEIN” BACTERIAL HARVESTING SYSTEM
2 PROCESS FOR MANUFACTURE OF CALCIUM CARBONATE FILTERS
3 H-ACID ISOLATION
4 A SUGGESTED APPROACH TO DETERMINING FEASIBLE PROCESS OPTIONS, AND OPERATING CONDITIONS FOR SEPARATION OF FINE SOLIDS FROM SUSPENSION
5 MODULI VERSUS SOLIDS CONTENT FORTYPICAL FORWARD FLOCCULATED “PROTEIN” SUSPENSIONS
6 DECISION TREE FOR SELECTION OF AS1 HARVESTING CONDITIONS WHEN PRINCIPAL CONSTRAINT CONCERNS THE DEGREE OF THICKENING REQUIRED IN THE CONCENTRATE
7 DECISION TREE FOR SELECTION OF AS1 HARVESTING CONDITIONS WHEN PRINCIPAL CONSTRAINT CONCERNS THE USE OF FLOTATION AS A UNIT OPERATION FOR THICKENING
8 DECISION TREE FOR SELECTION OF AS1 HARVESTING CONDITIONS WHEN PRINCIPAL CONSTRAINT CONCERNS THE QUALITY OF THE RECYCLED LIQUOR
9 MODULUS SOLIDS CONTENT CURVES FOR THEVARIOUS COAGULATED LATICES
BENFIELD LIQUOR - DETERMINATION OF IRON
BENFIELD LIQUOR: DETERMINATION OF IRON
SCOPE AND FIELD OF APPLICATION
This method is suitable for the determination of the total iron in Benfield liquor samples up to a concentration of approximately 100 ppm m/v.
Other Separations Techniques for Suspensions
Other Separations Techniques for Suspensions
PRESSURE-DRIVEN MEMBRANE SEPARATION
PROCESSES
1.1 INTRODUCTION
1.2 MEMBRANES
1.3 OPERATION
1.4 FACTORS AFFECTING PERFORMANCE
1.4.1 Polarization / Fouling
1.4.2 Pressure
1.4.3 Crossflow
1.4.4 Temperature
1.4.5 Concentration
1.4.6 Membrane Pore Size
1.4.7 Particle Size
1.4.8 Particle Charge
1.4.9 Other Factors
1.5 ADVANTAGES / LIMITATIONS
1.6 SUMMARY OF SYMBOLS USED
2 ELECTRO-DIALYSIS
2.1 INTRODUCTION
2.2 EQUIPMENT
2.3 IMPORTANT PARAMETERS IN ED
2.4 EXAMPLES
3 ELECTRODEWATERING AND ELECTRODECANTATION
3.1 INTRODUCTION
3.2 PRINCIPLES AND OPERATION
3.3 EQUIPMENT AND OPERATING PARAMETERS
3.4 EXAMPLES
4 MAGNETIC SEPARATION METHODS
5 REFERENCES
FIGURES
1 APPLICATION RANGES FOR MEMBRANE SEPARATION TECHNIQUES
2 SIMPLE UF / CMF RIG
4 FLUX VERSUS PRESSURE
5 ELECTRODIALYSIS PROCESS
6 ELECTRODIALYSIS PLANT FOR BATCH PROCESS
7 DEPENDENCE OF MEMBRANE AREA AND ENERGY ON
CURRENT DENSITY
8 DIFFUSION ACROSS THE BOUNDARY LAYER
Determination of Hydrocarbons in Anhydrous Ammonia By Gas Chromatography
Determination of Hydrocarbons in Anhydrous Ammonia By Gas Chromatography
SCOPE AND FIELD OF APPLICATION
The method is suitable for the determination of hydrocarbons from C1 to C4 (see 6.4.2) in gaseous ammonia, or in mixtures of ammonia and air. It is valid for concentrations in the range 10-10000 ppm.
The method may be used for the analysis of the atmosphere from a ships hold After purging with ammonia and for the analysis of gasified liquid anhydrous ammonia during or after loading. In these cases, hydrocarbon contamination may arise from the previous cargo of the vessel, the nature of which should be ascertained prior to carrying out the analysis
Determination of Carbon Dioxide, Ethane And Nitrogen in Natural Gas by Gas C...
Determination of Carbon Dioxide, Ethane
And Nitrogen in Natural Gas by Gas Chromatography
1 SCOPE AND FIELD OF APPLICATION
This document is a method for the determination of carbon dioxide, ethane and nitrogen in natural gas in the range 0-10% v/v.
2 PRINCIPLE
The gas sample will be injected automatically by a ten port valve onto the poraplot U column. The nitrogen will elute first and be switched to the mole sieve column. The mole sieve column will be isolated and the poraplot column will elute the carbon dioxide and ethane via a restrictor column to the detector. After the elution of the carbon dioxide and ethane the poraplot column will be back flushed. Then the nitrogen will be allowed to elute from the mole sieve column (see figure 1.) ...
Carbon Formation in Mixed Feed Preheat Coils
Carbon Formation in Mixed Feed Preheat Coils:
Maximum Mixed Feed Pre-heat Temperature
What follows is a crude but effective routine, which evaluates the maximum possible temperature allowable to prevent excessive carbon laydown in the mixed feed pre-heat coils.
Integration of Special Purpose Centrifugal Pumps into a Process
Integration of Special Purpose Centrifugal Pumps into a Process
CONTENTS
1 SCOPE
2 PRELIMINARY CHOICE OF PUMP
SECTION A - INLET CONDITIONS
Al Calculation of Basic Nett Positive Suction Head (NPSH)
A2 Correction to Basic NPSH for Temperature Rise at Pump Inlet
A3 Correction to Basic NPSH for Acceleration Head
A4 Calculation of Available NPSH
A5 Correction to NPSH for Fluid Properties
A6 Calculation of Suction Specific Speed
A7 Priming
A8 Submergence
SECTION B – FLOW / HEAD RATING SEQUENCE
B1 Calculation of Static Head
B2 Calculation of Margins for Control
B3 Calculation of Q-H Duty
B4 Stability and Parallel Operation
B5 Corrections to Q-H Duty for Fluid Properties
B6 Guide to Pump Type and Speed
SECTION C – DRIVER POWER RATING
C1 Estimation of Pump Efficiency
C2 Calculation of Absorbed Power
C3 Calculation of Driver Power Rating
C4 Preliminary Power Ratings of Electric Motors
C5 Starting Conditions for Electric Motors
C6 Reverse Flow and Reverse Rotation
SECTION D - CASING PRESSURE RATING
D1 Calculation of Maximum Inlet Pressure
D2 Calculation of Differential Pressure
D3 Pressure Waves
D4 Pressure due to Liquid Thermal Expansion
D5 Casing Hydrostatic Test Pressure
SECTION E – SEALING CONSIDERATIONS
E1 Preliminary Choice of Seal
E2 Fluid Attributes
E3 Definition of Flushing Arrangements
APPENDICES
A RELIABILITY CLASSIFICATION
B SYMBOLS AND PREFERRED UNITS
DOCUMENTS REFERRED TO IN THIS ENGINEERING DESIGN GUIDE
OXIDATIVE COUPLING COMBINED WITH DISTILLATION TO REMOVE MERCAPTAN SULFUR FROM...
OXIDATIVE COUPLING COMBINED WITH DISTILLATION TO REMOVE MERCAPTAN SULFUR FROM NGLS
CONTENTS
Background
Figure 1. Typical LPG Fractionation line-up and Sulfur Compound Distribution
Potential Market for low Sulfur LPGs
Sulfur removal from LPGs
Oxidative coupling combined with distillation
Figure 2. Debutanizer with Catalytic Oxidative Coupling
Aspen Simulation Results
Integration of reaction and distillation
Technical Issues
Practical Issues
Future Considerations
Market Issues
Technical Issues
Additional Technical Requirements
References
Appendix
Kerosene Sweetening
Reactor Modeling Tools – Multiple Regressions
Reactor Modeling Tools – Multiple Regressions
CONTENTS
0 INTRODUCTION
1 SCOPE
2 THEORY
3 EXCEL 2007: MULTIPLE REGRESSIONS
3.1 Overview
3.2 Multiple Regression Using the Data Analysis ADD-IN
3.3 Interpret Regression Statistics Table
3.4 Interpret ANOVA Table
3.5 Interpret Regression Coefficients Table
3.6 Confidence Intervals for Slope Coefficients
3.7 Test Hypothesis of Zero Slope Coefficients ("Test of Statistical Significance")
3.8 Test Hypothesis on a Regression Parameter
3.8.1 Using the p-value approach
3.8.2 Using the critical value approach
3.9 Overall Test of Significance of the Regression Parameters
3.10 Predicted Value of Y Given Regressors
3.11 Excel Limitations
4 SPECIAL FEATURES REQUIRING MORE SOPHISTICATED TECHNIQUES
5 USER INFORMATION SUPPLIED
A SUBROUTINE
B DATA
C RESULTS
6 EXAMPLE
BENFIELD LIQUOR:Determination of Diethanolamine Using an Auto Titrator
BENFIELD LIQUOR:Determination of Diethanolamine Using an Auto Titrator
1 SCOPE AND FIELD OF APPLICATION
This method is suitable for the determination of diethanolamine in Benfield Liquor.
2 PRINCIPLE
Diethanolamine is converted quantitatively into ammonia by boiling in the presence of sulfuric acid and copper sulfate. The ammonia is distilled from an alkaline medium and absorbed into boric acid. The solution is titrated with standard acid.
Quality of Life Correlates to Oil Consumption - Infographic
Quality of Life Correlates to Oil Consumption - Infographic
Determination of Residue and Oil in Anhydrous Ammonia
Plant Analytical Techniques
Determination of Residue and Oil in Anhydrous Ammonia
This method is suitable for the determination of residue and oil in anhydrous ammonia.
FIELD OF APPLICATION
This method may be applied to standard and premium grade anhydrous ammonia having residue content in the range 10-5000 micrograms per gram and oil content in the range l-500 micrograms per gram
OLEFIN HYDROGENATION - VULCAN Series VHT-S101/S103
GBH Enterprises specializes in catalyst and process technology for refining, gas processing, and petrochemical industries. They provide catalyst performance evaluation, heat and mass balance analysis, and commercialization of new technologies. The document describes two case studies of olefin hydrogenation using Vulcan catalysts. Both cases require a recycle stream to control exotherms. The results show the reactor sizing and operating parameters needed to meet a 5-year minimum catalyst life for both cases.
Determination of Residue on Evaporation in Anhydrous Ammonia
Determination of Residue on Evaporation in Anhydrous Ammonia
1 SCOPE AND FIELD OF APPLICATION
This method is suitable for the determination of the residue left after evaporation i.e., the non-volatile material in ammonia solution.
2 PRINCIPLE
A known weight of sample is evaporated to dryness in a platinum dish on a steam bath. The increase in mass of the dish is measured.
Determination of Anions by Ion Chromatography
Determination of Anions by Ion Chromatography
1 SCOPE AND FIELD OF APPLICATION
This method is suitable for the determination of inorganic anions in Ammonia Solution in the range 100 ppb to 50 ppm m/v.
2 PRINCIPLE
The sample is passed through a column of anion exchange resin, on which the anions are absorbed and separated. They are then eluted with dilute sodium carbonate/sodium hydrogen carbonate solution and passed through a suppressor. This replaces the cations with hydrogen ions and thus reduces the background conductivity of the eluent. Final measurement is by conductivity
Viewers also liked (20)
Determination of Argon in Ammonia Plant Process Gas Streams by Gas Chromatogr...
Determination of Argon in Ammonia Plant Process Gas Streams by Gas Chromatogr...
Determination of Hydrocarbons in Anhydrous Ammonia By Gas Chromatography
Determination of Hydrocarbons in Anhydrous Ammonia By Gas Chromatography
Determination of Carbon Dioxide, Ethane And Nitrogen in Natural Gas by Gas C...
Determination of Carbon Dioxide, Ethane And Nitrogen in Natural Gas by Gas C...
Integration of Special Purpose Centrifugal Pumps into a Process
Integration of Special Purpose Centrifugal Pumps into a Process
OXIDATIVE COUPLING COMBINED WITH DISTILLATION TO REMOVE MERCAPTAN SULFUR FROM...
OXIDATIVE COUPLING COMBINED WITH DISTILLATION TO REMOVE MERCAPTAN SULFUR FROM...
BENFIELD LIQUOR:Determination of Diethanolamine Using an Auto Titrator
BENFIELD LIQUOR:Determination of Diethanolamine Using an Auto Titrator
Quality of Life Correlates to Oil Consumption - Infographic
Quality of Life Correlates to Oil Consumption - Infographic
Determination of Residue and Oil in Anhydrous Ammonia
Determination of Residue and Oil in Anhydrous Ammonia
OLEFIN HYDROGENATION - VULCAN Series VHT-S101/S103
OLEFIN HYDROGENATION - VULCAN Series VHT-S101/S103
Determination of Residue on Evaporation in Anhydrous Ammonia
Determination of Residue on Evaporation in Anhydrous Ammonia
Similar to In-Situ Oxidation Procedure for High and Low Temperature Shift Catalysts
Hydrogenation Reactor Run Away Conditions
Temperature excursions in hydrogenation reactors may have several causes, the most common ones being:-
i) Loss of recycle quench system. This could be either the liquid or gas stream. The condition is made worse if the make-up gas keeps flowing.
ii) Excessive temperatures. The loss of cooling medium ........
Air / Steam Regeneration Procedure for Primary Reforming Ccatalyst
GBH Enterprises specializes in refinery process catalysts, including performance evaluation, analysis, and development of new technologies. The document provides procedures for air/steam regeneration of primary reforming catalysts either during shutdown or startup. During shutdown, steaming should continue for two hours before introducing a small amount of air to burn off carbon deposits, monitored by CO2 levels. During startup, normal heating with steam is followed by the same air regeneration process once temperatures reach 1300-1325°F, before removing air and resuming steam for two hours prior to introducing feed gas.
Fixed Bed Adsorber Design Guidelines
OVERVIEW - FIXED BED ADSORBER DESIGN GUIDELINES
Fixed-bed adsorber design is based upon the following considerations:
• Adsorbent bed profile and media loading capacity characteristics for the specific application and adsorbent material used.
• Pressure drop characteristics across the adsorbent bed.
• Reaction kinetics.
Typically, adsorber design entails use of the following methodology:
• Adsorbent selection based upon performance and application information.
• Bed sizing based upon adsorbent loading data and service life requirements.
• Bed sizing adjustment based upon pressure drop criteria.
• Bed sizing adjustment based upon reaction kinetics criteria.
A discussion of each design consideration follows.
Guidelines for Charging Primary Reforming Catalyst via Wet Method
GBH Enterprises specializes in refinery process catalysts, performance evaluation, and new technology development for refining and petrochemical industries. They provide guidelines for charging primary reforming catalysts via a wet method which involves partially filling the reformer tubes with water during catalyst charging, allowing for drainage, and slowly drying the catalyst over 10-12 hours at increasing temperatures below the dew point to avoid breakage. The guidelines are meant to supplement accepted plant procedures for safe catalyst charging and start-up.
H - Acid Caustic Fusion Stage
H - Acid Caustic Fusion Stage
CONTENTS
0 INTRODUCTION
1 DESIGN INFORMATION
1.1 Reactor Type
1.2 Temperature Range
1.3 Pressure Range
1.4 Chemical System
2 BACKGROUND
3 KINETICS AND MECHANISM
4 MAXIMUM YIELD AND IMPLICATIONS FOR REACTOR DESIGN
5 USE OF DESIGN MODEL FOR START-UP AND MANUFACTURING MONITORING
6 BIBLIOGRAPHY
FIGURES
1 FUSION MODEL OUTLINE MECHANISM AND KINETIC SCHEME
2 TEST RUN OPTIMIZATION OF HEATING TIME 3600 kg/h STEAM
Fixed Bed Reactor Scale-up Checklist
Fixed Bed Reactor Scale-up Checklist
The purpose of this checklist is to identify the stages and potential problems associated with the scale up of fixed bed reactors from the drawing board to the full scale plant, and to determine how they should be checked.
The checking can be done using various methods. These are:
• Literature data.
• Lab testing.
• Calculation.
• Modeling.
• Semi-tech testing.
• Piloting or Sidestream testing.
Identifying the stages that need to be addressed for a particular catalyst/reactor development will help in estimating the time needed for the development of the reactor
Naphtha Steam Reforming Catalyst Reduction with Methanol
Procedure for Naphtha Steam Reforming Catalyst Reduction with Methanol
Scope
This procedure applies to the in situ reduction of VULCAN Series steam reforming catalysts using methanol cracking to form hydrogen over the catalyst in the steam reformer.
The procedure is likely to be applied to plants using only heavier feeds (e.g.: LPG and/or naphtha) and some combination of VULCAN Series catalysts.
Introduction
A small number of steam reforming plants do not have an available source of the commonly used reducing media (e.g.: hydrogen, hydrogen-rich off-gas, natural gas). These plants will usually operate on LPG and/or naphtha feed only where cracking of this hydrocarbon is not usually advised for reduction of the steam reforming catalyst ...
Debottlenecking Claus Sulfur Recovery Units: An Investigation of the applicat...
Debottlenecking Claus Sulfur Recovery Units: An Investigation of the application of Zinc Titanates
1 Executive Summary
2 Claus Process
2.1 Partial Combustion Claus
2.2 Split Flow Claus
2.3 Sulfur Recycle Claus
3 Zinc Titanates
4 Application of Zinc Titanate to Debottleneck Partial Combustion Claus by 10%
4.1 Process
4.2 ASPEN Modeling Results
4.3 Cost of Zinc Titanate Bed Installation
4.3.1 Basis of Costing
4.3.2 Zinc Titanate Beds
4.3.3 Regen Cooler
4.3.4 Blowers
4.3.5 Results
4.4 Alternative Debottlenecking Technology for Partial Combustion Claus
4.5 Cost of 10% Debottlenecking Using COPE Process
5 Debottlenecking Claus Split Flow System by 10% with Zinc Titanates
6 Debottlenecking Claus Sulfur Recycle System With Zinc Titanate
7 Effect of Zinc Titanate Debottlenecking on Existing Tail; Gas Treatment Systems
7.1 Selectox
7.2 SuperClaus99
7.3 Superclaus 99.5
7.4 SCOT Process
7.5 Zinc Titanate as a Claus Tail Gas Treatment
7.6 H2S Removal Efficiency With Zinc Titanate
8 Effects on COS and CS2 Formation
9 Questions for further Investigation
FIGURES
Figure 1 Claus Unit and TGCU
Figure 2 Claus Process
Figure 3 Typical Claus Sulfur Recovery Unit
Figure 4 Two-Stage Claus SRU
Figure 5 The Super Claus Process
Figure 6 SCOT
Figure 7 SCOT/BSR-MDEA (or clone) TGCU
REFERENCES: PATENTS
US4333855_PROMOTED_ZINC_TITANATE_CATALYTIC_AGENT
US4394297_ZINC_TITANATE_CATALYST
US6338794B1_DESULFURIZATION_ZINC_TITANATE_SORBENTS
Data Sources For Calculating Chemical Reaction Equilibria
Data Sources For Calculating Chemical Reaction Equilibria
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 BACKGROUND TO THEORY
5 BIBLIOGRAPHY
Methanator Water Wash Procedures
Methanator Water Wash Procedures
To avoid nickel carbonyl formation, it is preferable to heat the catalyst above 400oF in nitrogen or some other CO free gas. If this is impractical and the catalyst must be heated with process gas, low pressure, high rate heating should be employed. The gas must be vented at a height and ideally flared. Care should be taken to ensure all methanator and local drains are shut.
METHANOL PLANT - SHALE GAS FEED PRETREATMENT
METHANOL PLANT - SHALE GAS FEED PRETREATMENT
CASE STUDY #091406
Case Background
A Methanol plant operator would like to examine the technical feasibility of using Shale Gas as a feedstock to their Methanol plant.
The first step in the Methanol production process is gas pretreatment. The purpose of gas pretreatment is to make the gas suitable for the downstream processes. There are two groups of compounds that are usually present in natural gas and that should be removed during pretreatment—the associate NGL and the sulfur-containing compounds. Some natural gas reservoirs may also have other trace components that must be removed, but these are not discussed here.
This case study examines the impact of CO2 (Carbon Dioxide) on the pre-treatment section design, performance and efficiency of ACME Methanol Plant’ feed gas pre-treatment section.
Case 1: Normal Shale Gas
Case 2: “Bad Gas”
Case 3: Low CO2
Case 4: High CO2
Mixing of Gas Liquid Systems
Mixing of Gas Liquid Systems
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 FLUID INTERFACE AND REACTION EFFECTS
5 EQUIPMENT SELECTION
6 DESIGN OF BUBBLE COLUMNS
6.1 Recommendations
6.2 Design Procedure
6.3 Mass Transfer and Voidage
6.4 Heat Transfer
6.5 Mixing Patterns
7 DESIGN OF GAS-LIQUID STIRRED VESSELS
(Re > 104 ONLY)
7.1 Recommendations
7.2 Design Procedure
7.3 Mass Transfer
8 DESIGN OF GAS-LIQUID STATIC MIXERS
8.1 Recommendations
8.2 Design Procedure
9 NOMENCLATURE
TABLE
1 COMPARISON OF DIFFERENT GAS-LIQUID
CONTACTING DEVICES
FIGURES
1 BUBBLE COLUMN
2 STIRRED VESSEL
3 JET-MIXED VESSEL
4 STATIC MIXER
5 JET EJECTORS
6 THIN FILM
7 THIN FILM
8 DOUGH MIXER
9 IN-LINE DYNAMIC MIXER
10 MULTI-PIPE GAS SPARGER
11 VESSEL GEOMETRY
12 AGITATORS
Integration of Special Purpose Reciprocating Compressors into a Process
1 SCOPE
2 CHOICE OF COMPRESSOR TYPE
2.1 Parameters
2.2 Preliminary Choice of Machine Type
2.3 Review of Other Types of Compressor
3 CHOICE OF NUMBER OF COMPRESSORS
3.1 Influence of Reliability Classification
3.2 Driver Considerations
3.3 Deterioration of Standby Machines
4 EFFECTS OF PROCESS GAS COMPOSITION
4.1 Particulate Contamination
4.2 Droplets in Suspension
4.3 Polymer Deposit
4.4 Molecular Weight Variation
4.5 Compressibility Variation
4.6 Gas Dryness
4.7 Gas Solution in Lubricating Oil for Cylinder and Gland
5 THROUGHPUT REGULATION
5.1 Inlet Line Throttle Valve
5.2 Inlet Line Cut-off Valve
5.3 Compressor Inlet Valve Lifter
5.4 Clearance Volume Variation
5.5 Speed Variation
5.6 Bypass
5.7 Hybrid Regulation Systems
6 PRINCIPAL FEATURES
6.1 Calculate Discharge Gas Temperature
6.2 Choice of Number of Stages
6.3 Configuration
6.4 Valve Operation Limit on Piston Speed
6.5 Limits for Mean Piston Speed
6.6 Estimation of Volumetric Efficiency
6.7 Estimation of Crankshaft Rotational Speed
6.8 Calculation of Piston Diameter
6.9 Choice of Number of Cylinders
7 DRIVER TYPE
7.1 Electric Motors
7.2 Steam Turbines
7.3 Special Drivers
8 VESSELS
APPENDICES
A RELIABILITY CLASSIFICATION
B CONDITIONS FOR LUBRICATED CYLINDERS AND GLANDS
C ESTIMATE OF LUBE OIL CONTAMINATION OF PROCESS GAS
D INFLUENCE OF GAS COMPOSITION AND MACHINE CONSTRUCTION
ON FILLED PTFE PISTON RING SEALS
E LIMITS ON GAS TEMPERATURES
FIGURES
1 SELECTION CHART
2 DESIGN SEQUENCE 1 - ESTIMATE NUMBER OF STAGES
3 DESIGN SEQUENCE 2 - ESTIMATE CYLINDER SIZES
Gas Mixing
Gas Mixing
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 RECOMMENDATIONS FOR GAS MIXING:
PLUG FLOW
5 RECOMMENDATIONS FOR GAS MIXING:
BACKMIXED INITIAL ZONE
6 BIBLIOGRAPHY
Distillation Sequences, Complex Columns and Heat Integration
Distillation Sequences, Complex Columns and Heat Integration
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 SEQUENCING OF SIMPLE COLUMNS
4.1 Sidestream Columns
4.2 Multi-Feed Columns
5 SIMPLE COLUMN SEQUENCING AND HEAT
INTEGRATION INTERACTIONS
5.1 Energy Quantity and Quality
5.2 Heat Integration within the Total Flowsheet
6 COMPLEX COLUMN ARRANGEMENTS
6.1 Indirect Sequence with Vapor Link
6.2 Sidestream Systems
6.3 Pre-Fractionator Systems
7 COMPLEX COLUMNS AND HEAT INTEGRATION
INTERACTIONS
FIGURES
1 DIRECT AND INDIRECT SEQUENCES
2 A SINGLE SIDESTREAM COLUMN REPLACING 2
SIMPLE COLUMNS
3 A TYPICAL MULTI-FEED COLUMN
4 TYPICAL GRAND COMPOSITION CURVE
5 TYPICAL INDIRECT SEQUENCE WITH VAPOUR LINK
6 SIDESTREAM STRIPPER AND SIDESTREAM
RECTIFIER
7 SIMPLEST PRE-FRACTIONATOR SYSTEM
8 SIMPLEST PRE-FRACTIONATOR SYSTEM
9 PETLYUK COLUMN
Heating and Cooling of Batch Processes
Heating and Cooling of Batch Processes
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
3.1 units
4 STATEMENT OF THE PROBLEM
5 DEVELOPMENT OF THE METHOD
5.1 Assumptions
5.2 Basic Equations
6 APPLICATION OF THE METHOD
6.1 Determining the Behavior of an Existing System
6.2 Specifying the Heat Transfer Duty for a New System
APPENDICES
A DERIVATION OF THE EQUATIONS
B WORKED EXAMPLES
FIGURES
1 CASES CONSIDERED
Liquid Liquid Extraction - Basic Principles
Liquid Liquid Extraction - Basic Principles
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 LIQUID-LIQUID EXTRACTION PROCESS
4.1 General
4.2 Choice of Solvent
4.3 Principles of Extraction
4.4 Liquid-Liquid Extraction Equipment
4.5 Operating Modes
4.6 Operating And Design Pitfalls
5 BIBLIOGRAPHY
FIGURES
1 SCHEMATIC OUTLINE OF LIQUID-LIQUID EXTRACTION PROCESS: COUNTERCURRENT FLOW IN ROTATING DISC CONTACTOR
2 COUNTERCURRENT EXTRACTION WITH REFLUX
Discharge and Reduction Procedures for Methanation Catalyst
Methanation Catalyst
VULCAN Series VSG-N101/102
SHUTDOWN
CATALYST DISCHARGE
NICKEL CARBONYL HAZARD
REDUCTION PROCEDURE
ACTIVATED CARBON- AIR-STEAM REGENERATION PROCEDURE
GBH Enterprises provides activated carbon regeneration services for refineries using a multi-step air-steam process. The process involves slowly depressurizing the carbon bed, applying steam to desorb contaminants, then introducing increments of air up to 5000 ppm to burn off remaining contaminants. Temperature and oxygen levels are monitored throughout to ensure safe regeneration of the activated carbon for reuse in purification processes.
Hydrogenolysis Operations Manual
Introduction
VULCAN Series VHT-S101
Catalyst storage, handling, charging
Health and safety precautions
Start-up of VHT-S101 hydrogenation catalyst
Operation of VHT-S101 hydrogenation catalyst
Shut-down of VHT-S101 hydrogenation catalyst
Sulfiding of hydrodesulfurization catalysts
Catalyst Discharge
Similar to In-Situ Oxidation Procedure for High and Low Temperature Shift Catalysts (20)
Air / Steam Regeneration Procedure for Primary Reforming Ccatalyst
Air / Steam Regeneration Procedure for Primary Reforming Ccatalyst
Guidelines for Charging Primary Reforming Catalyst via Wet Method
Guidelines for Charging Primary Reforming Catalyst via Wet Method
Naphtha Steam Reforming Catalyst Reduction with Methanol
Naphtha Steam Reforming Catalyst Reduction with Methanol
Debottlenecking Claus Sulfur Recovery Units: An Investigation of the applicat...
Debottlenecking Claus Sulfur Recovery Units: An Investigation of the applicat...
Data Sources For Calculating Chemical Reaction Equilibria
Data Sources For Calculating Chemical Reaction Equilibria
Integration of Special Purpose Reciprocating Compressors into a Process
Integration of Special Purpose Reciprocating Compressors into a Process
Distillation Sequences, Complex Columns and Heat Integration
Distillation Sequences, Complex Columns and Heat Integration
Discharge and Reduction Procedures for Methanation Catalyst
Discharge and Reduction Procedures for Methanation Catalyst
ACTIVATED CARBON- AIR-STEAM REGENERATION PROCEDURE
ACTIVATED CARBON- AIR-STEAM REGENERATION PROCEDURE
More from Gerard B. Hawkins
Pressure Relief Systems Vol 2
Pressure Relief Systems Vol 2
Causes of Relief Situations
This Volume 2 is a guide to the qualitative identification of common causes of overpressure in process equipment. It cannot be exhaustive; the process engineer and relief systems team should look for any credible situation in addition to those given in this Part which could lead to a need for pressure relief (a relief situation).
Pressure Relief Systems
This document provides guidelines for engineering design of pressure relief systems. It discusses key principles such as identifying potential overpressure and underpressure causes, sizing relief systems to prevent hazards, and safely disposing of relieved materials. The guidelines cover statutory requirements, recommended design procedures, and documentation standards. The overall goal is to preserve equipment integrity and prevent failure from over or under pressure during all process phases.
GAS DISPERSION - A Definitive Guide to Accidental Releases of Heavy Gases
GAS DISPERSION - A Definitive Guide to Accidental Releases of Heavy Gases
This Process Safety Guide has been written with the aim of assisting process engineers, hazard analysts and environmental advisers in carrying out gas dispersion calculations. The Guide aims to provide assistance by:
• Improving awareness of the range of dispersion models available within GBHE, and providing guidance in choosing the most appropriate model for a particular application.
• Providing guidance to ensure that source terms and other model inputs are correctly specified, and the models are used within their range of applicability.
• Providing guidance to deal with particular topics in gas dispersion such as dense gas dispersion, complex terrain, and modeling the chemistry of oxides of nitrogen.
• Providing general background on air quality and dispersion modeling issues such as meteorology and air quality standards.
• Providing example calculations for real practical problems.
SCOPE
The gas dispersion guide contains the following Parts:
1 Fundamentals of meteorology.
2 Overview of air quality standards.
3 Comparison between different air quality models.
4 Designing a stack.
5 Dense gas dispersion.
6 Calculation of source terms.
7 Building wake effects.
8 Overview of the chemistry of the oxides of nitrogen.
9 Overview of the ADMS complex terrain module.
10 Overview of the ADMS deposition module.
11 ADMS examples.
12 Modeling odorous releases.
13 Bibliography of useful gas dispersion books and reports.
14 Glossary of gas dispersion modeling terms.
Appendix A : Modeling Wind Generation of Particulates.
APPENDIX B TABLE OF PROPERTY VALUES FOR SPECIFIC CHEMICALS
El impacto en el rendimiento del catalizador por envenenamiento y ensuciamien...
El documento describe los procesos de refinería y catalizadores, así como los efectos del envenenamiento y ensuciamiento en el rendimiento de los catalizadores. El envenenamiento reduce la actividad de los catalizadores al bloquear los sitios activos o modificar la química de la superficie, lo que afecta la actividad y selectividad. Los niveles bajos de contaminantes tienen un mayor impacto en catalizadores con menor área de superficie. El envenenamiento también puede causar cambios estructurales en el catalizador y permitir
Adiabatic Reactor Analysis for Methanol Synthesis Plant Note Book Series: P...
The document discusses adiabatic reactor analysis for methanol synthesis from syngas. It provides the reaction kinetics and calculates conversion, temperature, and reactor volume needed at different conversions. Energy and mass balances are used to derive relationships between conversion, temperature and reaction rate. Data is generated to plot conversion versus volumetric flow rate for reactor sizing. The plot indicates a continuous stirred tank reactor (CSTR) could achieve 85% conversion before switching to a plug flow reactor (PFR) for higher conversion with less volume.
Calculation of an Ammonia Plant Energy Consumption:
Calculation of an Ammonia Plant Energy Consumption:
Case Study: #06023300
Plant Note Book Series: PNBS-0602
CONTENTS
0 SCOPE
1 CALCULATION OF NATURAL GAS PROCESS FEED CONSUMPTION
2 CALCULATION OF NATURAL GAS PROCESS FUEL CONSUMPTION
3 CALCULATION OF NATURAL GAS CONSUMPTION FOR PILOT BURNERS OF FLARES
4 CALCULATION OF DEMIN. WATER FROM DEMIN. UNIT
5 CALCULATION OF DEMIN. WATER TO PACKAGE BOILERS
6 CALCULATION OF MP STEAM EXPORT
7 CALCULATION OF LP STEAM IMPORT
8 DETERMINATION OF ELECTRIC POWER CONSUMPTION
9 DETERMINATION OF THE TOTAL ENERGY CONSUMPTION OF THE AMMONIA PLANT ISBL
10 ADJUSTMENT OF ELECTRIC POWER CONSUMPTION FOR TEST RUN CONDITIONS
11 CALCULATION OF AMMONIA SHARE IN MP STEAM CONSUMPTION IN UTILITIES
12 CALCULATION OF AMMONIA SHARE IN ELECTRIC POWER CONSUMPTION IN UTILITIES
13 DETERMINATION OF THE TOTAL ENERGY CONSUMPTION OF THE AMMONIA PLANT OSBL
14 DETERMINATION OF THE TOTAL ENERGY CONSUMPTION OF THE AMMONIA PLANT
Pickling & Passivation
Ammonia Plant Technology
Pre-Commissioning Best Practices
GBHE-APT-0102
PICKLING & PASSIVATION
CONTENTS
1 PURPOSE OF THE WORK
2 CHEMICAL CONCEPT
3 TECHNICAL CONCEPT
4 WASTES & SAFETY CONCEPT
5 TARGET RESULTS
6 THE GENERAL CLEANING SEQUENCE MANAGEMENT
6.6.1 Pre-cleaning or “Physical Cleaning
6.6.2 Pre-rinsing
6.6.3 Chemical Cleaning
6.6.4 Critical Factors in Cleaning Success
6.6.5 Rinsing
6.6.6 Inspection and Re-Cleaning, if Necessary
7 Systems to be treated by Pickling/Passivation
Piping and Vessels Flushing and Cleaning Procedure
Ammonia Plant Technology
Pre-Commissioning Best Practices
Piping and Vessels Flushing and Cleaning Procedure
CONTENTS
1 Scope
2 Aim/purpose
3 Responsibilities
4 Procedure
4.1 Main cleaning methods
4.1.1 Mechanical cleaning
4.1.2 Cleaning with air
4.1.3 Cleaning with steam (for steam networks only)
4.1.4 Cleaning with water
4.2 Choice of the cleaning method
4.3 Cleaning preparation
4.4 Protection of the devices included in the network
4.5 Protection of devices in the vicinity of the network
4.6 Water flushing procedure
4.6.1 Specific problems of water flushing
4.6.2 Preparation for water flushing
4.6.3 Performing a water flush
4.6.4 Cleanliness criteria
4.7 Air blowing procedure
4.7.1 Specific problems of air blowing
4.7.2 Preparation for air blowing
4.7.3 Performing air blowing
4.7.4 Cleanliness checks
4.8 Steam blowing procedure
4.8.1 Specific problems of steam blowing
4.8.2 Preparation for steam blowing
4.8.3 Performing steam blowing
4.8.4 Cleanliness checks
4.9 Chemical cleaning procedure
4.9.1 Specific problems of cleaning with a chemical solution
4.9.2 Preparation for chemical cleaning
4.9.3 Performing a chemical cleaning
4.9.4 Cleanliness criteria
4.10 Re-assembly - general guideline
4.11 Preservation of flushed piping
DESIGN OF VENT GAS COLLECTION AND DESTRUCTION SYSTEMS
DESIGN OF VENT GAS COLLECTION AND DESTRUCTION SYSTEMS
CONTENTS
1 INTRODUCTION
1.1 Purpose
1.2 Scope of this Guide
1.3 Use of the Guide
2 ENVIRONMENTAL ISSUES
2.1 Principal Concerns
2.2 Mechanisms for Ozone Formation
2.3 Photochemical Ozone Creation Potential
2.4 Health and Environmental Effects
2.5 Air Quality Standards for Ground Level Concentrations of Ozone, Targets for Reduction of VOC Discharges and Statutory Discharge Limits
3 VENTS REDUCTION PHILOSOPHY
3.1 Reduction at Source
3.2 End-of-pipe Treatment
4 METHODOLOGY FOR COLLECTION & ASSESSMENT OF PROCESS FLOW DATA
4.1 General
4.2 Identification of Vent Sources
4.3 Characterization of Vents
4.4 Quantification of Process Vent Flows
4.5 Component Flammability Data Collection
4.6 Identification of Operating Scenarios
4.7 Quantification of Flammability Characteristics for Combined Vents
4.8 Identification, Quantification and Assessment of Possibility of Air Ingress Routes
4.9 Tabulation of Data
4.10 Hazard Study and Risk Assessment
4.11 Note on Aqueous / Organic Wastes
4.12 Complexity of Systems
4.13 Summary
5 SAFE DESIGN OF VENT COLLECTION HEADER SYSTEMS
5.1 General
5.2 Process Design of Vent Headers
5.3 Liquid in Vent Headers
5.4 Materials of Construction
5.5 Static Electricity Hazard
5.6 Diversion Systems
5.7 Snuffing Systems
6 SAFE DESIGN OF THERMAL OXIDISERS
6.1 Introduction
6.2 Design Basis
6.3 Types of High Temperature Thermal Oxidizer
6.4 Refractories
6.5 Flue Gas Treatment
6.6 Control and Safety Systems
6.7 Project Program
6.8 Commissioning
6.9 Operational and Maintenance Management
APPENDICES
A GLOSSARY
B FLAMMABILITY
C EXAMPLE PROFORMA
D REFERENCES
DOCUMENTS REFERRED TO IN THIS PROCESS GUIDE
TABLE
1 PHOTOCHEMICAL OZONE CREATION POTENTIAL REFERENCED
TO ETHYLENE AS UNITY
FIGURES
1 SCHEMATIC OF TYPICAL VENT COLLECTION AND THERMAL OXIDIZER SYSTEM
2 TYPICAL KNOCK-OUT POT WITH LUTED DRAIN
3 SCHEMATIC OF DIVERSION SYSTEM
4 CONVENTIONAL VERTICAL THERMAL OXIDIZER
5 CONVENTIONAL OXIDIZER WITH INTEGRAL WATER SPARGER
6 THERMAL OXIDIZER WITH STAGED AIR INJECTION
7 DOWN-FIRED UNIT WITH WATER BATH QUENCH
8 FLAMELESS THERMAL OXIDATION UNIT
9 THERMAL OXIDIZER WITH REGENERATIVE HEAT RECOVERY
10 TYPICAL PROJECT PROGRAM
11 TYPICAL FLAMMABILITY DIAGRAM
12 EFFECT OF DILUTION WITH AIR
13 EFFECT OF DILUTION WITH AIR ON 100 Rm³ OF FLAMMABLE GAS
PRACTICAL GUIDE ON THE SELECTION OF PROCESS TECHNOLOGY FOR THE TREATMENT OF A...
PRACTICAL GUIDE ON THE SELECTION OF PROCESS TECHNOLOGY FOR THE TREATMENT OF AQUEOUS ORGANIC EFFLUENT STREAMS
CONTENTS
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
3.1 IPU
3.2 AOS
3.3 BODs
3.4 COD
3.5 TOC
3.6 Toxicity
3.7 Refractory Organics/Hard COD
3.8 Heavy Metals
3.9 EA
3.10 Biological Treatment Terms
3.11 BATNEEC
3.12 BPEO
3.13 EQS/LV
3.14 IPC
3.15 VOC
3.16 F/M Ratio
3.17 MLSS
3.18 MLVSS
4 DESIGN/ECONOMIC GUIDELINES
5 EUROPEAN LEGISLATION
5.1 General
5.2 Integrated Pollution Control (IPC)
5.3 Best Available Techniques Not Entailing Excessive Costs (BATNEEC)
5.4 Best Practicable Environmental Option (BPEO)
5.5 Environmental Quality Standards(EQS)
6 IPU EXIT CONCENTRATION
7 SITE/LOCAL REQUIREMENTS
8 PROCESS SELECTION PROCEDURE
8.1 Waste Minimization Techniques (WMT)
8.2 AOS Stream Definition
8.3 Technical Check List
8.4 Preliminary Selection of Suitable Technologies
8.5 Process Sequences
8.6 Economic Evaluation
8.7 Process Selection
APPENDICES
A DIRECTIVE 76/464/EEC - LIST 1
B DIRECTIVE 76/464/EEC - LIST 2
C THE EUROPEAN COMMISSION PRIORITY CANDIDATE LIST
D THE UK RED LIST
E CURRENT VALUES FOR EUROPEAN COMMUNITY ENVIRONMENTAL QUALITY STANDARDS AND CORRESPONDING LIMIT VALUES
F ESTABLISHED TECHNOLOGIES
G EMERGING TECHNOLOGY
H PROPRIETARY/LESS COMMON TECHNOLOGIES
J COMPARATIVE COST DATA
PRACTICAL GUIDE ON THE REDUCTION OF DISCHARGES TO ATMOSPHERE OF VOLATILE ORGA...
PRACTICAL GUIDE ON THE REDUCTION OF DISCHARGES TO ATMOSPHERE OF VOLATILE ORGANIC COMPOUNDS (VOCs)
FOREWORD
CONTENTS
1 INTRODUCTION
2 THE NEED FOR VOC CONTROL
3 CONTROL AT SOURCE
3.1 Choice or Solvent
3.2 Venting Arrangements
3.3 Nitrogen Blanketing
3.4 Pump Versus Pneumatic Transfer
3.5 Batch Charging
3.6 Reduction of Volumetric Flow
3.7 Stock Tank Design
4 DISCHARGE MEASUREMENT
4.1 By Inference or Calculation
4.2 Flow Monitoring Equipment
4.3 Analytical Instruments
4.4 Vent Emissions Database
5 ABATEMENT TECHNOLOGY
5.1 Available Options
5.2 Selection of Preferred Option
5.3 Condensation
5.4 Adsorption
5.5 Absorption
5.6 Thermal Incineration
5.7 Catalytic Oxidation
5.8 Biological Filtration
5.9 Combinations of Process technologies
5.10 Processes Under Development
6 GLOSSARY OF TERMS
7 REFERENCES
Appendix 1. Photochemical Ozone Creation Potentials
Appendix 2. Examples of Adsorption Preliminary Calculations
Appendix 3. Example of Thermal Incineration Heat and Mass Balance
Appendix 4. Cost Correlations
Getting the Most Out of Your Refinery Hydrogen Plant
Getting the Most Out of Your Refinery Hydrogen Plant
Contents
Summary
1 Introduction
2 "On-purpose" Hydrogen Production
3 Operational Aspects
4 Uprating Options on the Steam Reformer
4.1 Steam Reforming Catalysts and Tube Metallurgy
4.2 Oxygen-blown Secondary Reformer
4.3 Pre-reforming
4.4 Post-reforming
5 Downstream Units
6 Summary of Uprating Options
7 Conclusions
EMERGENCY ISOLATION OF CHEMICAL PLANTS
EMERGENCY ISOLATION OF CHEMICAL PLANTS
CONTENTS
1 Introduction
2 When should Emergency Isolation Valves be Installed
3 Emergency Isolation Valves and Associated Equipment
3.1 Installations on existing plant
3.2 Actuators
3.3 Power to close or power to open
3.4 The need for testing
3.5 Hand operated Emergency Valves
3.6 The need to stop pumps in an emergency
3.7 Location of Operating Buttons
3.8 Use of control valves for Isolation
4 Detection of Leaks and Fires
5 Precautions during Maintenance
6 Training Operators to use Emergency Isolation Valves
7 Emergency Isolation when no remotely operated valve is available
References
Glossary
Appendix I Some Fires or Serious Escapes of Flammable Gases or Liquids that could have been controlled by Emergency Isolation Valves
Appendix II Some typical Installations
Purificación – Mecanismos de Reacción
Purificación – Mecanismos de Reacción
Deberes de purificación
Eliminación de azufre
Eliminación de haluro
Reducción de gases - CO, H2
Oxígeno
Mercurio, Arsano
Hidrocarburos insaturados
CO2, oxigenadores
Amine Gas Treating Unit - Best Practices - Troubleshooting Guide
Amine Gas Treating Unit Best Practices - Troubleshooting Guide for H2S/CO2 Amine Systems
Contents
Process Capabilities for gas treating process
Typical Amine Treating
Typical Amine System Improvements
Primary Equipment Overview
Inlet Gas Knockout
Absorber
Three Phase Flash Tank
Lean/Rich Heat Exchanger
Regenerator
Filtration
Amine Reclaimer
Operating Difficulties Overview
Foaming
Failure to Meet Gas Specification
Solvent Losses
Corrosion
Typical Amine System Improvements
Degradation of Amines and Alkanolamines during Sour Gas Treating
APPENDIX
Best Practices - Troubleshooting Guide
Investigation of the Potential Use of (IILs) Immobilized Ionic Liquids in Sha...
The document discusses using immobilized ionic liquids (IILs) in shale gas sweetening reactions. It proposes immobilizing a cobalt catalyst in the surface ionic liquid layer of a solid supported ionic liquid catalyst. This would create a "homogeneous catalyst" dissolved within the fixed IIL layer. Competing reactions like oxidation of sulfides to sulfones would need to be considered. Related work on using similar approaches for hydroformylation reactions is referenced. The concept aims to develop a solid IIL catalyst for sweetening reactions involving oxidation using techniques from other areas like hydroformylation.
GBHE Over View jan_13_español
El documento proporciona una descripción general de los servicios y tecnologías de procesamiento de catalizadores de GBH Enterprises Ltd. (GBHE), incluyendo refinación de petróleo, procesamiento de gas, industrias petroquímicas y venta de catalizadores. GBHE ofrece servicios de ingeniería, soporte técnico y consultoría, así como una línea de catalizadores patentados para aplicaciones como desulfuración y purificación de gas.
FCC Catalyst Design: Morphology, Physiology, Reaction Chemistry and Manufactu...
FCC Catalyst Design: Morphology, Physiology, Reaction Chemistry and Manufacturing
Introduction
FCC Catalyst Components
- the Zeolite
- the Matrix
- Additives ( ZSM-5, other )
Catalyst Manufacturing
Reaction Chemistry
- b scission (cracking)
- hydrogen transfer
- heat balance considerations
Selecting the Right Combination
Burner Design, Operation and Maintenance on Ammonia Plants
The document discusses burner design, operation, and maintenance on ammonia plants. It covers reformer burner types and designs, including premix and staged burners. It also addresses combustion characteristics like excess air and fuel viscosity effects. Maintenance best practices like checking burner pressures and atomizing steam temperatures are emphasized. Low NOx equipment uses techniques like staged air, fuel, and flue gas recirculation to reduce emissions. Good combustion requires attention to design, operation, maintenance, and partnership among related roles.
DEACTIVATION OF METHANOL SYNTHESIS CATALYSTS
DEACTIVATION OF METHANOL SYNTHESIS CATALYSTS
CONTENTS
1 INTRODUCTION
2 THERMAL SINTERING
3 CATALYST POISONING
4 REACTANT INDUCED DEACTIVATION
5 SUMMARY
TABLES
1 DEACTIVATION PROCESSES ON METHANOL SYNTHESIS CATALYSTS
2 MELTING POINT, HUTTIG AND TAMMANN TEMPERATURES OF COPPER, IRON AND NICKEL
3 SINTERING RATE CONSTANTS CALCULATED INLET AND OUTLET SIDE STREAM UNIT FOR VULCAN VSG-M101
4 COMPARISON BETWEEN CALCULATED S∞ AND DISCHARGED MEASUREMENTS ON VULCAN VSG-M101
5 EFFECT OF POSSIBLE CONTAMINANTS AND POISONS ON CU/ZNO/AL2O3 CATALYSTS FOR METHANOL SYNTHESIS
6 GUARD SCREENING TEST RESULTS ON METHANOL MICRO-REACTOR. EFFECT OF DEPOSITED METALS ON METHANOL ACTIVITY
FIGURES
1 THE HΫTTIG AND TAMMANN TEMPERATURES OF THE COMPONENTS OF A SYNTHESIS CATALYST
2 A SCHEMATIC REPRESENTATION OF TWO CATALYST SINTERING MECHANISMS
3 SIDE STREAM DATA FOR VULCAN VSG-M101. INLET TEMPERATURE 242 OC, PRESSURE 1500 PSI, GAS COMPOSITION 6% CO, 9.2% CO2, 66.9% H2, 2.5% N2 AND 15.4% CH4, SPACE VELOCITY 17,778 HR-1. MEAN OUTLET TEMPERATURE 280 OC
4 TEMPERATURE DEPENDENCE OF THE RATE OF SINTERING
5 MECHANISM OF SULFUR RETENTION
6 CORRELATION OF SULFUR CAPACITY WITH TOTAL SURFACE AREA
7 EFFECT OF DEPOSITED (NI+FE) PPM ON METHANOL SYNTHESIS CATALYST ACTIVITY
8 DISCHARGED (FE + NI) DEPOSITION LEVELS ON METHANOL SYNTHESIS PLANT SAMPLES
9 EPMA ANALYSIS OF DISCHARGED LABORATORY SAMPLE OF POISONED VULCAN VSG-M101
10 THE EFFECT OF CO2 ON SYNTHESIS CATALYST DEACTIVATION
REFERENCES
More from Gerard B. Hawkins (20)
GAS DISPERSION - A Definitive Guide to Accidental Releases of Heavy Gases
GAS DISPERSION - A Definitive Guide to Accidental Releases of Heavy Gases
El impacto en el rendimiento del catalizador por envenenamiento y ensuciamien...
El impacto en el rendimiento del catalizador por envenenamiento y ensuciamien...
Adiabatic Reactor Analysis for Methanol Synthesis Plant Note Book Series: P...
Adiabatic Reactor Analysis for Methanol Synthesis Plant Note Book Series: P...
Calculation of an Ammonia Plant Energy Consumption:
Calculation of an Ammonia Plant Energy Consumption:
Piping and Vessels Flushing and Cleaning Procedure
Piping and Vessels Flushing and Cleaning Procedure
DESIGN OF VENT GAS COLLECTION AND DESTRUCTION SYSTEMS
DESIGN OF VENT GAS COLLECTION AND DESTRUCTION SYSTEMS
PRACTICAL GUIDE ON THE SELECTION OF PROCESS TECHNOLOGY FOR THE TREATMENT OF A...
PRACTICAL GUIDE ON THE SELECTION OF PROCESS TECHNOLOGY FOR THE TREATMENT OF A...
PRACTICAL GUIDE ON THE REDUCTION OF DISCHARGES TO ATMOSPHERE OF VOLATILE ORGA...
PRACTICAL GUIDE ON THE REDUCTION OF DISCHARGES TO ATMOSPHERE OF VOLATILE ORGA...
Getting the Most Out of Your Refinery Hydrogen Plant
Getting the Most Out of Your Refinery Hydrogen Plant
Amine Gas Treating Unit - Best Practices - Troubleshooting Guide
Amine Gas Treating Unit - Best Practices - Troubleshooting Guide
Investigation of the Potential Use of (IILs) Immobilized Ionic Liquids in Sha...
Investigation of the Potential Use of (IILs) Immobilized Ionic Liquids in Sha...
FCC Catalyst Design: Morphology, Physiology, Reaction Chemistry and Manufactu...
FCC Catalyst Design: Morphology, Physiology, Reaction Chemistry and Manufactu...
Burner Design, Operation and Maintenance on Ammonia Plants
Burner Design, Operation and Maintenance on Ammonia Plants
Recently uploaded
Letter and Document Automation for Bonterra Impact Management (fka Social Sol...
Sidekick Solutions uses Bonterra Impact Management (fka Social Solutions Apricot) and automation solutions to integrate data for business workflows.
We believe integration and automation are essential to user experience and the promise of efficient work through technology. Automation is the critical ingredient to realizing that full vision. We develop integration products and services for Bonterra Case Management software to support the deployment of automations for a variety of use cases.
This video focuses on automated letter generation for Bonterra Impact Management using Google Workspace or Microsoft 365.
Interested in deploying letter generation automations for Bonterra Impact Management? Contact us at sales@sidekicksolutionsllc.com to discuss next steps.
Main news related to the CCS TSI 2023 (2023/1695)
An English 🇬🇧 translation of a presentation to the speech I gave about the main changes brought by CCS TSI 2023 at the biggest Czech conference on Communications and signalling systems on Railways, which was held in Clarion Hotel Olomouc from 7th to 9th November 2023 (konferenceszt.cz). Attended by around 500 participants and 200 on-line followers.
The original Czech 🇨🇿 version of the presentation can be found here: https://www.slideshare.net/slideshow/hlavni-novinky-souvisejici-s-ccs-tsi-2023-2023-1695/269688092 .
The videorecording (in Czech) from the presentation is available here: https://youtu.be/WzjJWm4IyPk?si=SImb06tuXGb30BEH .
Building Production Ready Search Pipelines with Spark and Milvus
Spark is the widely used ETL tool for processing, indexing and ingesting data to serving stack for search. Milvus is the production-ready open-source vector database. In this talk we will show how to use Spark to process unstructured data to extract vector representations, and push the vectors to Milvus vector database for search serving.
5th LF Energy Power Grid Model Meet-up Slides
5th Power Grid Model Meet-up
It is with great pleasure that we extend to you an invitation to the 5th Power Grid Model Meet-up, scheduled for 6th June 2024. This event will adopt a hybrid format, allowing participants to join us either through an online Mircosoft Teams session or in person at TU/e located at Den Dolech 2, Eindhoven, Netherlands. The meet-up will be hosted by Eindhoven University of Technology (TU/e), a research university specializing in engineering science & technology.
Power Grid Model
The global energy transition is placing new and unprecedented demands on Distribution System Operators (DSOs). Alongside upgrades to grid capacity, processes such as digitization, capacity optimization, and congestion management are becoming vital for delivering reliable services.
Power Grid Model is an open source project from Linux Foundation Energy and provides a calculation engine that is increasingly essential for DSOs. It offers a standards-based foundation enabling real-time power systems analysis, simulations of electrical power grids, and sophisticated what-if analysis. In addition, it enables in-depth studies and analysis of the electrical power grid’s behavior and performance. This comprehensive model incorporates essential factors such as power generation capacity, electrical losses, voltage levels, power flows, and system stability.
Power Grid Model is currently being applied in a wide variety of use cases, including grid planning, expansion, reliability, and congestion studies. It can also help in analyzing the impact of renewable energy integration, assessing the effects of disturbances or faults, and developing strategies for grid control and optimization.
What to expect
For the upcoming meetup we are organizing, we have an exciting lineup of activities planned:
-Insightful presentations covering two practical applications of the Power Grid Model.
-An update on the latest advancements in Power Grid -Model technology during the first and second quarters of 2024.
-An interactive brainstorming session to discuss and propose new feature requests.
-An opportunity to connect with fellow Power Grid Model enthusiasts and users.
System Design Case Study: Building a Scalable E-Commerce Platform - Hiike
This case study explores designing a scalable e-commerce platform, covering key requirements, system components, and best practices.
Your One-Stop Shop for Python Success: Top 10 US Python Development Providers
Simplify your search for a reliable Python development partner! This list presents the top 10 trusted US providers offering comprehensive Python development services, ensuring your project's success from conception to completion.
GraphRAG for Life Science to increase LLM accuracy
GraphRAG for life science domain, where you retriever information from biomedical knowledge graphs using LLMs to increase the accuracy and performance of generated answers
Driving Business Innovation: Latest Generative AI Advancements & Success Story
Are you ready to revolutionize how you handle data? Join us for a webinar where we’ll bring you up to speed with the latest advancements in Generative AI technology and discover how leveraging FME with tools from giants like Google Gemini, Amazon, and Microsoft OpenAI can supercharge your workflow efficiency.
During the hour, we’ll take you through:
Guest Speaker Segment with Hannah Barrington: Dive into the world of dynamic real estate marketing with Hannah, the Marketing Manager at Workspace Group. Hear firsthand how their team generates engaging descriptions for thousands of office units by integrating diverse data sources—from PDF floorplans to web pages—using FME transformers, like OpenAIVisionConnector and AnthropicVisionConnector. This use case will show you how GenAI can streamline content creation for marketing across the board.
Ollama Use Case: Learn how Scenario Specialist Dmitri Bagh has utilized Ollama within FME to input data, create custom models, and enhance security protocols. This segment will include demos to illustrate the full capabilities of FME in AI-driven processes.
Custom AI Models: Discover how to leverage FME to build personalized AI models using your data. Whether it’s populating a model with local data for added security or integrating public AI tools, find out how FME facilitates a versatile and secure approach to AI.
We’ll wrap up with a live Q&A session where you can engage with our experts on your specific use cases, and learn more about optimizing your data workflows with AI.
This webinar is ideal for professionals seeking to harness the power of AI within their data management systems while ensuring high levels of customization and security. Whether you're a novice or an expert, gain actionable insights and strategies to elevate your data processes. Join us to see how FME and AI can revolutionize how you work with data!
Operating System Used by Users in day-to-day life.pptx
Dive into the realm of operating systems (OS) with Pravash Chandra Das, a seasoned Digital Forensic Analyst, as your guide. 🚀 This comprehensive presentation illuminates the core concepts, types, and evolution of OS, essential for understanding modern computing landscapes.
Beginning with the foundational definition, Das clarifies the pivotal role of OS as system software orchestrating hardware resources, software applications, and user interactions. Through succinct descriptions, he delineates the diverse types of OS, from single-user, single-task environments like early MS-DOS iterations, to multi-user, multi-tasking systems exemplified by modern Linux distributions.
Crucial components like the kernel and shell are dissected, highlighting their indispensable functions in resource management and user interface interaction. Das elucidates how the kernel acts as the central nervous system, orchestrating process scheduling, memory allocation, and device management. Meanwhile, the shell serves as the gateway for user commands, bridging the gap between human input and machine execution. 💻
The narrative then shifts to a captivating exploration of prominent desktop OSs, Windows, macOS, and Linux. Windows, with its globally ubiquitous presence and user-friendly interface, emerges as a cornerstone in personal computing history. macOS, lauded for its sleek design and seamless integration with Apple's ecosystem, stands as a beacon of stability and creativity. Linux, an open-source marvel, offers unparalleled flexibility and security, revolutionizing the computing landscape. 🖥️
Moving to the realm of mobile devices, Das unravels the dominance of Android and iOS. Android's open-source ethos fosters a vibrant ecosystem of customization and innovation, while iOS boasts a seamless user experience and robust security infrastructure. Meanwhile, discontinued platforms like Symbian and Palm OS evoke nostalgia for their pioneering roles in the smartphone revolution.
The journey concludes with a reflection on the ever-evolving landscape of OS, underscored by the emergence of real-time operating systems (RTOS) and the persistent quest for innovation and efficiency. As technology continues to shape our world, understanding the foundations and evolution of operating systems remains paramount. Join Pravash Chandra Das on this illuminating journey through the heart of computing. 🌟
Ocean lotus Threat actors project by John Sitima 2024 (1).pptx
Ocean Lotus cyber threat actors represent a sophisticated, persistent, and politically motivated group that poses a significant risk to organizations and individuals in the Southeast Asian region. Their continuous evolution and adaptability underscore the need for robust cybersecurity measures and international cooperation to identify and mitigate the threats posed by such advanced persistent threat groups.
Choosing The Best AWS Service For Your Website + API.pptx
Have you ever been confused by the myriad of choices offered by AWS for hosting a website or an API?
Lambda, Elastic Beanstalk, Lightsail, Amplify, S3 (and more!) can each host websites + APIs. But which one should we choose?
Which one is cheapest? Which one is fastest? Which one will scale to meet our needs?
Join me in this session as we dive into each AWS hosting service to determine which one is best for your scenario and explain why!
TrustArc Webinar - 2024 Global Privacy Survey
How does your privacy program stack up against your peers? What challenges are privacy teams tackling and prioritizing in 2024?
In the fifth annual Global Privacy Benchmarks Survey, we asked over 1,800 global privacy professionals and business executives to share their perspectives on the current state of privacy inside and outside of their organizations. This year’s report focused on emerging areas of importance for privacy and compliance professionals, including considerations and implications of Artificial Intelligence (AI) technologies, building brand trust, and different approaches for achieving higher privacy competence scores.
See how organizational priorities and strategic approaches to data security and privacy are evolving around the globe.
This webinar will review:
- The top 10 privacy insights from the fifth annual Global Privacy Benchmarks Survey
- The top challenges for privacy leaders, practitioners, and organizations in 2024
- Key themes to consider in developing and maintaining your privacy program
Monitoring and Managing Anomaly Detection on OpenShift.pdf
Monitoring and Managing Anomaly Detection on OpenShift
Overview
Dive into the world of anomaly detection on edge devices with our comprehensive hands-on tutorial. This SlideShare presentation will guide you through the entire process, from data collection and model training to edge deployment and real-time monitoring. Perfect for those looking to implement robust anomaly detection systems on resource-constrained IoT/edge devices.
Key Topics Covered
1. Introduction to Anomaly Detection
- Understand the fundamentals of anomaly detection and its importance in identifying unusual behavior or failures in systems.
2. Understanding Edge (IoT)
- Learn about edge computing and IoT, and how they enable real-time data processing and decision-making at the source.
3. What is ArgoCD?
- Discover ArgoCD, a declarative, GitOps continuous delivery tool for Kubernetes, and its role in deploying applications on edge devices.
4. Deployment Using ArgoCD for Edge Devices
- Step-by-step guide on deploying anomaly detection models on edge devices using ArgoCD.
5. Introduction to Apache Kafka and S3
- Explore Apache Kafka for real-time data streaming and Amazon S3 for scalable storage solutions.
6. Viewing Kafka Messages in the Data Lake
- Learn how to view and analyze Kafka messages stored in a data lake for better insights.
7. What is Prometheus?
- Get to know Prometheus, an open-source monitoring and alerting toolkit, and its application in monitoring edge devices.
8. Monitoring Application Metrics with Prometheus
- Detailed instructions on setting up Prometheus to monitor the performance and health of your anomaly detection system.
9. What is Camel K?
- Introduction to Camel K, a lightweight integration framework built on Apache Camel, designed for Kubernetes.
10. Configuring Camel K Integrations for Data Pipelines
- Learn how to configure Camel K for seamless data pipeline integrations in your anomaly detection workflow.
11. What is a Jupyter Notebook?
- Overview of Jupyter Notebooks, an open-source web application for creating and sharing documents with live code, equations, visualizations, and narrative text.
12. Jupyter Notebooks with Code Examples
- Hands-on examples and code snippets in Jupyter Notebooks to help you implement and test anomaly detection models.
Presentation of the OECD Artificial Intelligence Review of Germany
Consult the full report at https://www.oecd.org/digital/oecd-artificial-intelligence-review-of-germany-609808d6-en.htm
Skybuffer SAM4U tool for SAP license adoption
Manage and optimize your license adoption and consumption with SAM4U, an SAP free customer software asset management tool.
SAM4U, an SAP complimentary software asset management tool for customers, delivers a detailed and well-structured overview of license inventory and usage with a user-friendly interface. We offer a hosted, cost-effective, and performance-optimized SAM4U setup in the Skybuffer Cloud environment. You retain ownership of the system and data, while we manage the ABAP 7.58 infrastructure, ensuring fixed Total Cost of Ownership (TCO) and exceptional services through the SAP Fiori interface.
How to Interpret Trends in the Kalyan Rajdhani Mix Chart.pdf
A Mix Chart displays historical data of numbers in a graphical or tabular form. The Kalyan Rajdhani Mix Chart specifically shows the results of a sequence of numbers over different periods.
Artificial Intelligence for XMLDevelopment
In the rapidly evolving landscape of technologies, XML continues to play a vital role in structuring, storing, and transporting data across diverse systems. The recent advancements in artificial intelligence (AI) present new methodologies for enhancing XML development workflows, introducing efficiency, automation, and intelligent capabilities. This presentation will outline the scope and perspective of utilizing AI in XML development. The potential benefits and the possible pitfalls will be highlighted, providing a balanced view of the subject.
We will explore the capabilities of AI in understanding XML markup languages and autonomously creating structured XML content. Additionally, we will examine the capacity of AI to enrich plain text with appropriate XML markup. Practical examples and methodological guidelines will be provided to elucidate how AI can be effectively prompted to interpret and generate accurate XML markup.
Further emphasis will be placed on the role of AI in developing XSLT, or schemas such as XSD and Schematron. We will address the techniques and strategies adopted to create prompts for generating code, explaining code, or refactoring the code, and the results achieved.
The discussion will extend to how AI can be used to transform XML content. In particular, the focus will be on the use of AI XPath extension functions in XSLT, Schematron, Schematron Quick Fixes, or for XML content refactoring.
The presentation aims to deliver a comprehensive overview of AI usage in XML development, providing attendees with the necessary knowledge to make informed decisions. Whether you’re at the early stages of adopting AI or considering integrating it in advanced XML development, this presentation will cover all levels of expertise.
By highlighting the potential advantages and challenges of integrating AI with XML development tools and languages, the presentation seeks to inspire thoughtful conversation around the future of XML development. We’ll not only delve into the technical aspects of AI-powered XML development but also discuss practical implications and possible future directions.
June Patch Tuesday
Ivanti’s Patch Tuesday breakdown goes beyond patching your applications and brings you the intelligence and guidance needed to prioritize where to focus your attention first. Catch early analysis on our Ivanti blog, then join industry expert Chris Goettl for the Patch Tuesday Webinar Event. There we’ll do a deep dive into each of the bulletins and give guidance on the risks associated with the newly-identified vulnerabilities.
Recently uploaded (20)
Letter and Document Automation for Bonterra Impact Management (fka Social Sol...
Letter and Document Automation for Bonterra Impact Management (fka Social Sol...
Building Production Ready Search Pipelines with Spark and Milvus
Building Production Ready Search Pipelines with Spark and Milvus
System Design Case Study: Building a Scalable E-Commerce Platform - Hiike
System Design Case Study: Building a Scalable E-Commerce Platform - Hiike
Your One-Stop Shop for Python Success: Top 10 US Python Development Providers
Your One-Stop Shop for Python Success: Top 10 US Python Development Providers
GraphRAG for Life Science to increase LLM accuracy
GraphRAG for Life Science to increase LLM accuracy
Driving Business Innovation: Latest Generative AI Advancements & Success Story
Driving Business Innovation: Latest Generative AI Advancements & Success Story
Operating System Used by Users in day-to-day life.pptx
Operating System Used by Users in day-to-day life.pptx
Ocean lotus Threat actors project by John Sitima 2024 (1).pptx
Ocean lotus Threat actors project by John Sitima 2024 (1).pptx
Choosing The Best AWS Service For Your Website + API.pptx
Choosing The Best AWS Service For Your Website + API.pptx
Deep Dive: Getting Funded with Jason Jason Lemkin Founder & CEO @ SaaStr
Deep Dive: Getting Funded with Jason Jason Lemkin Founder & CEO @ SaaStr
Monitoring and Managing Anomaly Detection on OpenShift.pdf
Monitoring and Managing Anomaly Detection on OpenShift.pdf
Presentation of the OECD Artificial Intelligence Review of Germany
Presentation of the OECD Artificial Intelligence Review of Germany
How to Interpret Trends in the Kalyan Rajdhani Mix Chart.pdf
How to Interpret Trends in the Kalyan Rajdhani Mix Chart.pdf
In-Situ Oxidation Procedure for High and Low Temperature Shift Catalysts
- 1. GBH Enterprises, Ltd. In-Situ Oxidation Procedure for High and Low Temperature Shift Catalysts Process Information Disclaimer Information contained in this publication or as otherwise supplied to Users is believed to be accurate and correct at time of going to press, and is given in good faith, but it is for the User to satisfy itself of the suitability of the Product for its own particular purpose. GBHE gives no warranty as to the fitness of the Product for any particular purpose and any implied warranty or condition (statutory or otherwise) is excluded except to the extent that exclusion is prevented by law. GBHE accepts no liability for loss, damage or personnel injury caused or resulting from reliance on this information. Freedom under Patent, Copyright and Designs cannot be assumed. Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts / Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries Web Site: www.GBHEnterprises.com
- 2. In-Situ Oxidation Procedure - High and Low Temperature Shift Catalysts GBHE recommends the following procedure for the controlled oxidation of either an HTS or an LTS alone or an HTS in series with an LTS. 1. Remove and isolate all combustibles (e.g., feed gas or recycle synthesis gas) from the process by purging. 2. While purging the system, cool the HTS to 400oF and the LTS to 350oF with a steam or nitrogen flow at a space velocity of 600-1000 hr-1. NOTE: During this step, some catalyst oxidation will occur as evidenced by H2 present in the steam samples. 3. Meter 1% air into the steam ahead of the HTS. Expected delta T is 55oF per 1% air for the HTS and 25oF per 1% air for the LTS catalyst. 4. After 30 minutes, when the HTS bed exotherm has stabilized (still holding LTS inlet @ 350oF) increase air to 3%. 5. Continue to stepwise increase air addition pausing to monitor maximum bed exotherms. Since catalyst is to be discharged, mechanical or vessel temperature limitations are the primary concern. 6. When the temperature rise has passed completely through both the HTS and LTS beds, and inlet air rate is 7-10% the metered steam flow, the oxidation is considered complete. 7. Steam flow may be stopped and the catalyst cooled in air and discharged. Estimated time to totally oxidize both the HTS and LTS catalyst beds for air discharge is approximately 12 hours. Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts / Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries Web Site: www.GBHEnterprises.com
- 3. Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts / Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries Web Site: www.GBHEnterprises.com