This document proposes an efficient broadcast authentication protocol called X-TESLA to maximize the lifetime of wireless sensor networks. X-TESLA uses two levels of key chains that cross-authenticate each other to provide extendable authentication. It addresses issues like sleep modes, network failures, idle sessions, extended lifetime needs, and denial-of-service attacks. The document describes the initialization, broadcast authentication process, cross-authentication mechanism, and flexible constructions of X-TESLA to improve network lifetime significantly compared to other approaches.
Inverse Gamma Distribution based Delay and Slew Modeling for On- Chip VLSI RC...IDES Editor
The Elmore delay is fast becoming ineffective for
deep submicron technologies, and reduced order transfer
function delays are impractical for use as early-phase design
metrics or as design optimization cost functions. This paper
describes an accurate approach for fitting moments of the
impulse response to probability density functions so that delay
and slew metric can be estimated accurately at an early
physical design stage. PERI (Probability distribution function
Extension for Ramp Inputs) technique has been used that
extends the delay and slew metrics for step inputs to the more
general and realistic non-step or ramp inputs. The accuracy
of the proposed model is justified by the results obtained from
the proposed model and that of SPICE simulations
Low Power Clock Distribution Schemes in VLSI DesignIJERA Editor
This paper reviewed the comparison between different clock distribution schemes which used for low power
VLSI design which are the most important aspect in the industry. The main clock distribution schemes are
single driver clock scheme and distributed buffers clock scheme. There are different tradeoffs in both the
techniques such as size of buffers, number of buffers etc.
Redundant Actor Based Multi-Hole Healing System for Mobile Sensor NetworksEditor IJCATR
In recent years, the Mobile Wireless Sensor Network
is the emerging solution for monitoring of a specified region of
interest. Several anomalies can occur in WSNs that impair their
desired functionalities resulting in the formation of different
kinds of holes, namely: coverage holes, routing holes. Our
ultimate aim is to cover total area without coverage hole in
wireless sensor networks. We propose a comprehensive solution,
called holes detection and healing. We divided our proposed
work into two phases. The first phase consists of three sub- tasks;
Hole-identification, Hole-discovery and border detection. The
second phase treats the Hole-healing with novel concept, hole
healing area. It consists of two sub-tasks; Hole healing area
determination and node relocation.
We take some parts of a theoretical mobility model in a two-dimension grid proposed by Greenlaw and
Kantabutra to be our model. The model has eight necessary factors that we commonly use in a mobile
wireless network: sources or wireless signal providers, the directions that a source can move, users or
mobile devices, the given directions which define a user’s movement, the given directions which define a
source’s movement, source’s velocity, source’s coverage, and obstacles. However, we include only the
sources, source’s coverage, and the obstacles in our model. We define SQUARE GRID POINTS COVERAGE
(SGPC) problem to minimize number of sources with coverage radius of one to cover a square grid point
size of p with the restriction that all the sources must be communicable and proof that SGPC is in NPcomplete
class. We also give an APPROX-SQUARE-GRID-COVERAGE (ASGC) algorithm to compute the
approximate solution of SGPC. ASGC uses the rule that any number can be obtained from the addition of
3, 4 and 5 and then combines 3-gadgets, 4-gadgets and 5-gadgets to specify the position of sources to cover
a square grid point size of p. We find that the algorithm achieves an approximation ratio of
2
1 2 10 2
p
p .
Moreover, we state about the extension usage of our algorithm and show some examples. We show that if
we use ASPC on a square grid size of p and if sources can be moved, the area under the square grid can be
covered in eight-time-steps movement. We also prove that if we extend our source coverage radius to 1.59,
without any movement the area under the square gird will also be covered. Further studies are also
discussed and a list of some tentative problems is given in the conclusion.
Inverse Gamma Distribution based Delay and Slew Modeling for On- Chip VLSI RC...IDES Editor
The Elmore delay is fast becoming ineffective for
deep submicron technologies, and reduced order transfer
function delays are impractical for use as early-phase design
metrics or as design optimization cost functions. This paper
describes an accurate approach for fitting moments of the
impulse response to probability density functions so that delay
and slew metric can be estimated accurately at an early
physical design stage. PERI (Probability distribution function
Extension for Ramp Inputs) technique has been used that
extends the delay and slew metrics for step inputs to the more
general and realistic non-step or ramp inputs. The accuracy
of the proposed model is justified by the results obtained from
the proposed model and that of SPICE simulations
Low Power Clock Distribution Schemes in VLSI DesignIJERA Editor
This paper reviewed the comparison between different clock distribution schemes which used for low power
VLSI design which are the most important aspect in the industry. The main clock distribution schemes are
single driver clock scheme and distributed buffers clock scheme. There are different tradeoffs in both the
techniques such as size of buffers, number of buffers etc.
Redundant Actor Based Multi-Hole Healing System for Mobile Sensor NetworksEditor IJCATR
In recent years, the Mobile Wireless Sensor Network
is the emerging solution for monitoring of a specified region of
interest. Several anomalies can occur in WSNs that impair their
desired functionalities resulting in the formation of different
kinds of holes, namely: coverage holes, routing holes. Our
ultimate aim is to cover total area without coverage hole in
wireless sensor networks. We propose a comprehensive solution,
called holes detection and healing. We divided our proposed
work into two phases. The first phase consists of three sub- tasks;
Hole-identification, Hole-discovery and border detection. The
second phase treats the Hole-healing with novel concept, hole
healing area. It consists of two sub-tasks; Hole healing area
determination and node relocation.
We take some parts of a theoretical mobility model in a two-dimension grid proposed by Greenlaw and
Kantabutra to be our model. The model has eight necessary factors that we commonly use in a mobile
wireless network: sources or wireless signal providers, the directions that a source can move, users or
mobile devices, the given directions which define a user’s movement, the given directions which define a
source’s movement, source’s velocity, source’s coverage, and obstacles. However, we include only the
sources, source’s coverage, and the obstacles in our model. We define SQUARE GRID POINTS COVERAGE
(SGPC) problem to minimize number of sources with coverage radius of one to cover a square grid point
size of p with the restriction that all the sources must be communicable and proof that SGPC is in NPcomplete
class. We also give an APPROX-SQUARE-GRID-COVERAGE (ASGC) algorithm to compute the
approximate solution of SGPC. ASGC uses the rule that any number can be obtained from the addition of
3, 4 and 5 and then combines 3-gadgets, 4-gadgets and 5-gadgets to specify the position of sources to cover
a square grid point size of p. We find that the algorithm achieves an approximation ratio of
2
1 2 10 2
p
p .
Moreover, we state about the extension usage of our algorithm and show some examples. We show that if
we use ASPC on a square grid size of p and if sources can be moved, the area under the square grid can be
covered in eight-time-steps movement. We also prove that if we extend our source coverage radius to 1.59,
without any movement the area under the square gird will also be covered. Further studies are also
discussed and a list of some tentative problems is given in the conclusion.
Design of Efficient 4×4 Quaternary Vedic Multiplier Using Current-Mode Multi-...idescitation
Vedic multiplier is based on ancient Indian Vedic mathematics that offers
simpler and hierarchical structure. Multi-valued logic results in the effective utilization of
interconnections, which reduces the chip size and delay. This paper proposes a new design
of 4×4 Vedic multiplier using quaternary current-mode multi-valued logic, equivalent to
iplier has
very low transistor-count and consumes very low power as compared to other multiplier
designs. Since the performance of a digital signal processor depends mainly on the
multipliers used, the proposed approach can greatly enhance the performance of a digital
signal processing system.
All optical network design with even and odd nodeseSAT Journals
Abstract
We have studied the effects of OLTs and OADMs in WDM optical networks. All optical networks have proved to be cost efficient
and power saving in comparison to O-E-O networks. Cost of a network can further be reduced by minimizing the number of IP
router ports and the number of wavelengths required. It has been already studied the number of IP router ports required per node
and number of wavelengths required to carry a fixed amount of traffic, considering the network containing even and odd number
of routing nodes. And finally the result has been compared with other architectures like point to point WDM and hub networks,
finally all-optical networks proved to be most cost efficient in saving number of wavelength requirements and IP router port
requirements. In this paper we have compared all-optical network with itself, by taking even and odd number of nodes. That is we
have compared all-optical network containing even number of nodes with the same all-optical network containing odd number of
nodes. The result what we obtained is to honor same amount of traffic “t”, all-optical network containing odd number of nodes
require lesser number of wavelengths than its previous even number of nodes. We have here varied the number of nodes keeping
the amount of traffic fixed assuming static routing for simplicity of our work. Finally we observed the percentage of change in
wavelength requirements decreases on increasing number of nodes. That is for a large network number of wavelength
requirements are large for even number of nodes than odd number of nodes. But this difference is little more for a small network
size.
Keywords: Wavelength Division Multiplexing (WDM), PPWDM (Point to point WDM), Light paths, traffic, alloptical,
Erlang(E).
International Refereed Journal of Engineering and Science (IRJES)irjes
International Refereed Journal of Engineering and Science (IRJES) is a leading international journal for publication of new ideas, the state of the art research results and fundamental advances in all aspects of Engineering and Science. IRJES is a open access, peer reviewed international journal with a primary objective to provide the academic community and industry for the submission of half of original research and applications.
Analysis of Microstrip Finger on Bandwidth of Interdigital Band Pass Filter u...IJREST
ABSTRACT
In this paper, a novel method of bandwidth estimation using variation of finger length on interdigital band pass filter has been presented using artificial neural networks for desired frequency range between 1.5--3.5GHz. Interdigital filter is multifinger periodic structure which offers compact filter design space. An ANN model has been developed and tested for estimating the cut off frequency of band pass filter and performance is evaluated in terms of mean square error and concluded that RBF network is more accurate than MLPFFBP. The proposed method of design provides the exact bandwidth for particular finger length of filter without using painstaking calculation.
Keyword - Artificial neural networks (ANN), Multi layer Perceptron feed Forward back propagation (MLPFFBP), Interdigital
Simulation Time and Energy Test for Topology Construction Protocol in Wireles...ijeei-iaes
Coverage area and energy consumption are very big challenges in the field of Wireless Sensor Networks (WSNs) as it affects the number of sensors, connectivity and network. Since the sensors are operating on battery of limited power, it is a challenging aim to design an energy efficient Topology Control protocol, which can minimize the energy and thereby extend the lifetime of the network. Through this paper an attempt has been made in terms of simulation time and spent energy in construction of topology in the sensor network by comparing Just Tree and K-neigh Tree protocols. The result shows that K-neigh Tree protocol consumes less energy than Just Tree protocol.
Wireless sensor networks (WSN) have been widely used in various applications.
In these networks nodes collect data from the attached sensors and send their data to a base
station. However, nodes in WSN have limited power supply in form of battery so the nodes
are expected to minimize energy consumption in order to maximize the lifetime of WSN. A
number of techniques have been proposed in the literature to reduce the energy
consumption significantly. In this paper, we propose a new clustering based technique
which is a modification of the popular LEACH algorithm. In this technique, first cluster
heads are elected using the improved LEACH algorithm as usual, and then a cluster of
nodes is formed based on the distance between node and cluster head. Finally, data from
node is transferred to cluster head. Cluster heads forward data, after applying aggregation,
to the cluster head that is closer to it than sink in forward direction or directly to the sink.
This reduction in distance travelled improves the performance over LEACH algorithm
significantly.
In Cognitive Radio Networks (CRN), Cooperative Spectrum Sensing (CSS) is
used to improve performance of spectrum sensing techniques used for detection of licensed
(Primary) user’s signal. In CSS, the spectrum sensing information from multiple unlicensed
(Secondary) users are combined to take final decision about presence of primary signal. The
mixing techniques used to generate final decision about presence of PU’s signal are also
called as Fusion techniques / rules. The fusion techniques are further classified as data
fusion and decision fusion techniques. In data fusion technique all the secondary users
(SUs) share their raw information of spectrum detection like detected energy or other
statistical information, while in decision fusion technique all the SUs take their local
decisions and share the decision by sending ‘0’ or ‘1’ corresponding to absence and presence
of PU’s signal respectively. The rules used in decision fusion techniques are OR rule, AND
rule and K-out-of-N rule. The CSS is further classified as distributed CSS and centralized
CSS. In distributed CSS all the SUs share the spectrum detection information with each
other and by mixing the shared information; all the SUs take final decision individually. In
centralized CSS all the SUs send their detected information to a secondary base station /
central unit which combines the shared information and takes final decision. The secondary
base station shares the final decision with all the SUs in the CRN. This paper covers
overview of information fusion methods used for CSS and analysis of decision fusion rules
with simulation results.
Outage probability analysis of EH NOMA system network over Rayleigh fading ch...journalBEEI
Non-orthogonal multiple access (NOMA) with advantages such as superior spectral efficiency has been considered as a promising multiple access technique for the fifth-generation (5G) mobile networks. In this research, we propose energy harvesting (EH) NOMA system relaying network over Rayleigh fading channel using selection combining at the receiver. Firstly, we investigate the system performance in terms of the closed-form expression of the outage probability (OP). Here we compare the OP of two destination users of the proposed system. Finally, all the results is convinced by the Monte Carlo simulation. From the results, we can confirm that all the analytical and simulation results are the same in connection with the primary system parameters.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
COMPARATIVE ANALYSIS OF ROUTE INFORMATION BASED ENHANCED DIVIDE AND RULE STRA...ijsc
In wireless sensor network, routing data efficiently to the base station is a big issue and for this purpose, a
number of routing algorithms are invented by researchers. Clustering plays a very important role in the
design and as well as development of wireless sensor networks for well distribution of network and also to
route data efficiently. In this paper, we had done the enhancement of divide and rule strategy that is
basically route information protocol based upon static clustering and dynamic cluster head selection.
Simulation results show that our technique outperforms DR, LEACH, and AODV on the basis of packet
loss, delay, and throughput.
Investigation on energy harvesting enabled device-to-device networks in prese...TELKOMNIKA JOURNAL
Energy harvesting from ambient radio-frequency (RF) sources has been a novel approach for extending the lifetime of wireless networks. In this paper, a cooperative device-to-device (D2D) system with the aid of energy-constrained relay is considered. The relays are assumed to be able to harvest energy from information signal and co-channel interference (CCI) signals broadcasted by nearby traditional cellular users and forward the source’s signal to its desired destination (D2D user) utilizing amplify-andforward (AF) relaying protocol. Time switching protocol (TSR) and power splitting protocol (PSR) are proposed to assist energy harvesting and information processing at the relay. The proposed approaches are applied in a model with three nodes including the source (D2D user), the relay and the destination (D2D user), the system throughput is investigated in terms of the ergodic capacity and the outage capacity, where the analytical results are obtained approximately. Our numerical results verify the our derivations, and also points out the impact of CCI on system performance. Finally, this investigation provide fundamental design guidelines for selecting hardware of energy harvesting circuits that satisfies the requirements of a practical cooperative D2D system.
WALEACH: WEIGHT BASED ENERGY EFFICIENT ADVANCED LEACH ALGORITHMcscpconf
Designing a protocol stack for wireless sensor network (WSN) is a challenging task due to
energy, computational, communication and storage constraints. Energy spent for
communication between sensor nodes dominates the energy spent for the computation [1].
Multi-hop short range communication between wireless sensor nodes is energy efficient
compared to single-hop long range communication. Hierarchical clustering is one of the
possible solutions to save energy of wireless sensor nodes. LEACH and Advanced LEACH
(ALEACH) are energy efficient hierarchical clustering routing protocols. In this paper we
presented Weight based Advanced LEACH routing protocol - WALEACH. WALEACH selects
Cluster Head by assigning importance (weight) to different parameters used to select Cluster
Head, which makes the routing protocol energy efficient and improves life time of a wireless
sensor network. Simulation results shown here verify that WALEACH not only improves network life time compared to LEACH and ALEACH algorithms but Packet Reception Rate (PRR) too.
Design of Efficient 4×4 Quaternary Vedic Multiplier Using Current-Mode Multi-...idescitation
Vedic multiplier is based on ancient Indian Vedic mathematics that offers
simpler and hierarchical structure. Multi-valued logic results in the effective utilization of
interconnections, which reduces the chip size and delay. This paper proposes a new design
of 4×4 Vedic multiplier using quaternary current-mode multi-valued logic, equivalent to
iplier has
very low transistor-count and consumes very low power as compared to other multiplier
designs. Since the performance of a digital signal processor depends mainly on the
multipliers used, the proposed approach can greatly enhance the performance of a digital
signal processing system.
All optical network design with even and odd nodeseSAT Journals
Abstract
We have studied the effects of OLTs and OADMs in WDM optical networks. All optical networks have proved to be cost efficient
and power saving in comparison to O-E-O networks. Cost of a network can further be reduced by minimizing the number of IP
router ports and the number of wavelengths required. It has been already studied the number of IP router ports required per node
and number of wavelengths required to carry a fixed amount of traffic, considering the network containing even and odd number
of routing nodes. And finally the result has been compared with other architectures like point to point WDM and hub networks,
finally all-optical networks proved to be most cost efficient in saving number of wavelength requirements and IP router port
requirements. In this paper we have compared all-optical network with itself, by taking even and odd number of nodes. That is we
have compared all-optical network containing even number of nodes with the same all-optical network containing odd number of
nodes. The result what we obtained is to honor same amount of traffic “t”, all-optical network containing odd number of nodes
require lesser number of wavelengths than its previous even number of nodes. We have here varied the number of nodes keeping
the amount of traffic fixed assuming static routing for simplicity of our work. Finally we observed the percentage of change in
wavelength requirements decreases on increasing number of nodes. That is for a large network number of wavelength
requirements are large for even number of nodes than odd number of nodes. But this difference is little more for a small network
size.
Keywords: Wavelength Division Multiplexing (WDM), PPWDM (Point to point WDM), Light paths, traffic, alloptical,
Erlang(E).
International Refereed Journal of Engineering and Science (IRJES)irjes
International Refereed Journal of Engineering and Science (IRJES) is a leading international journal for publication of new ideas, the state of the art research results and fundamental advances in all aspects of Engineering and Science. IRJES is a open access, peer reviewed international journal with a primary objective to provide the academic community and industry for the submission of half of original research and applications.
Analysis of Microstrip Finger on Bandwidth of Interdigital Band Pass Filter u...IJREST
ABSTRACT
In this paper, a novel method of bandwidth estimation using variation of finger length on interdigital band pass filter has been presented using artificial neural networks for desired frequency range between 1.5--3.5GHz. Interdigital filter is multifinger periodic structure which offers compact filter design space. An ANN model has been developed and tested for estimating the cut off frequency of band pass filter and performance is evaluated in terms of mean square error and concluded that RBF network is more accurate than MLPFFBP. The proposed method of design provides the exact bandwidth for particular finger length of filter without using painstaking calculation.
Keyword - Artificial neural networks (ANN), Multi layer Perceptron feed Forward back propagation (MLPFFBP), Interdigital
Simulation Time and Energy Test for Topology Construction Protocol in Wireles...ijeei-iaes
Coverage area and energy consumption are very big challenges in the field of Wireless Sensor Networks (WSNs) as it affects the number of sensors, connectivity and network. Since the sensors are operating on battery of limited power, it is a challenging aim to design an energy efficient Topology Control protocol, which can minimize the energy and thereby extend the lifetime of the network. Through this paper an attempt has been made in terms of simulation time and spent energy in construction of topology in the sensor network by comparing Just Tree and K-neigh Tree protocols. The result shows that K-neigh Tree protocol consumes less energy than Just Tree protocol.
Wireless sensor networks (WSN) have been widely used in various applications.
In these networks nodes collect data from the attached sensors and send their data to a base
station. However, nodes in WSN have limited power supply in form of battery so the nodes
are expected to minimize energy consumption in order to maximize the lifetime of WSN. A
number of techniques have been proposed in the literature to reduce the energy
consumption significantly. In this paper, we propose a new clustering based technique
which is a modification of the popular LEACH algorithm. In this technique, first cluster
heads are elected using the improved LEACH algorithm as usual, and then a cluster of
nodes is formed based on the distance between node and cluster head. Finally, data from
node is transferred to cluster head. Cluster heads forward data, after applying aggregation,
to the cluster head that is closer to it than sink in forward direction or directly to the sink.
This reduction in distance travelled improves the performance over LEACH algorithm
significantly.
In Cognitive Radio Networks (CRN), Cooperative Spectrum Sensing (CSS) is
used to improve performance of spectrum sensing techniques used for detection of licensed
(Primary) user’s signal. In CSS, the spectrum sensing information from multiple unlicensed
(Secondary) users are combined to take final decision about presence of primary signal. The
mixing techniques used to generate final decision about presence of PU’s signal are also
called as Fusion techniques / rules. The fusion techniques are further classified as data
fusion and decision fusion techniques. In data fusion technique all the secondary users
(SUs) share their raw information of spectrum detection like detected energy or other
statistical information, while in decision fusion technique all the SUs take their local
decisions and share the decision by sending ‘0’ or ‘1’ corresponding to absence and presence
of PU’s signal respectively. The rules used in decision fusion techniques are OR rule, AND
rule and K-out-of-N rule. The CSS is further classified as distributed CSS and centralized
CSS. In distributed CSS all the SUs share the spectrum detection information with each
other and by mixing the shared information; all the SUs take final decision individually. In
centralized CSS all the SUs send their detected information to a secondary base station /
central unit which combines the shared information and takes final decision. The secondary
base station shares the final decision with all the SUs in the CRN. This paper covers
overview of information fusion methods used for CSS and analysis of decision fusion rules
with simulation results.
Outage probability analysis of EH NOMA system network over Rayleigh fading ch...journalBEEI
Non-orthogonal multiple access (NOMA) with advantages such as superior spectral efficiency has been considered as a promising multiple access technique for the fifth-generation (5G) mobile networks. In this research, we propose energy harvesting (EH) NOMA system relaying network over Rayleigh fading channel using selection combining at the receiver. Firstly, we investigate the system performance in terms of the closed-form expression of the outage probability (OP). Here we compare the OP of two destination users of the proposed system. Finally, all the results is convinced by the Monte Carlo simulation. From the results, we can confirm that all the analytical and simulation results are the same in connection with the primary system parameters.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
COMPARATIVE ANALYSIS OF ROUTE INFORMATION BASED ENHANCED DIVIDE AND RULE STRA...ijsc
In wireless sensor network, routing data efficiently to the base station is a big issue and for this purpose, a
number of routing algorithms are invented by researchers. Clustering plays a very important role in the
design and as well as development of wireless sensor networks for well distribution of network and also to
route data efficiently. In this paper, we had done the enhancement of divide and rule strategy that is
basically route information protocol based upon static clustering and dynamic cluster head selection.
Simulation results show that our technique outperforms DR, LEACH, and AODV on the basis of packet
loss, delay, and throughput.
Investigation on energy harvesting enabled device-to-device networks in prese...TELKOMNIKA JOURNAL
Energy harvesting from ambient radio-frequency (RF) sources has been a novel approach for extending the lifetime of wireless networks. In this paper, a cooperative device-to-device (D2D) system with the aid of energy-constrained relay is considered. The relays are assumed to be able to harvest energy from information signal and co-channel interference (CCI) signals broadcasted by nearby traditional cellular users and forward the source’s signal to its desired destination (D2D user) utilizing amplify-andforward (AF) relaying protocol. Time switching protocol (TSR) and power splitting protocol (PSR) are proposed to assist energy harvesting and information processing at the relay. The proposed approaches are applied in a model with three nodes including the source (D2D user), the relay and the destination (D2D user), the system throughput is investigated in terms of the ergodic capacity and the outage capacity, where the analytical results are obtained approximately. Our numerical results verify the our derivations, and also points out the impact of CCI on system performance. Finally, this investigation provide fundamental design guidelines for selecting hardware of energy harvesting circuits that satisfies the requirements of a practical cooperative D2D system.
WALEACH: WEIGHT BASED ENERGY EFFICIENT ADVANCED LEACH ALGORITHMcscpconf
Designing a protocol stack for wireless sensor network (WSN) is a challenging task due to
energy, computational, communication and storage constraints. Energy spent for
communication between sensor nodes dominates the energy spent for the computation [1].
Multi-hop short range communication between wireless sensor nodes is energy efficient
compared to single-hop long range communication. Hierarchical clustering is one of the
possible solutions to save energy of wireless sensor nodes. LEACH and Advanced LEACH
(ALEACH) are energy efficient hierarchical clustering routing protocols. In this paper we
presented Weight based Advanced LEACH routing protocol - WALEACH. WALEACH selects
Cluster Head by assigning importance (weight) to different parameters used to select Cluster
Head, which makes the routing protocol energy efficient and improves life time of a wireless
sensor network. Simulation results shown here verify that WALEACH not only improves network life time compared to LEACH and ALEACH algorithms but Packet Reception Rate (PRR) too.
Maximizing Network Lifetime by Using Smart Cluster Head Selectioniosrjce
IOSR Journal of Electronics and Communication Engineering(IOSR-JECE) is a double blind peer reviewed International Journal that provides rapid publication (within a month) of articles in all areas of electronics and communication engineering and its applications. The journal welcomes publications of high quality papers on theoretical developments and practical applications in electronics and communication engineering. Original research papers, state-of-the-art reviews, and high quality technical notes are invited for publications.
A Review: Compensation of Mismatches in Time Interleaved Analog to Digital Co...IJERA Editor
The execution of today's correspondence frameworks is exceedingly subject to the utilized Analog-to-Digital converters (ADCs), and with a specific end goal to give more flexibility and exactness to the developing correspondence innovations, superior-ADCs are needed. In this respect, the time-interleaved operation of an exhibit of ADCs (TI-ADC) might be a sensible result. A TI-ADC can build its throughput by utilizing M channel ADCs or sub converters in parallel and examining the data motion in a period-interleaved way. In any case, the execution of a TI-ADC gravely suffers from the bungles around the channel ADCs. In this paper we survey the advancement in the configuration of low-intricacy advanced remedy structures and calculations for time-interleaved ADCs in the course of the most recent five years. We devise a discrete-time model, state the outline issue, and finally infer the calculations and structures. Specifically, we examine proficient calculations to outline time-differing remedy filters and additionally iterative structures using polynomial based filters. Thusly, the remuneration structure may be utilized to repay time-differing recurrence reaction befuddles in time-interleaved ADCs, and in addition to remake uniform examples from nonuniformly tested indicators. We examine the recompense structure, research its execution, and exhibit requisition zones of the structure through various illustrations. At long last, we give a standpoint to future examination questions.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
Design of c slotted microstrip antenna using artificial neural network modeleSAT Journals
Abstract In this paper, neural network model has been used to estimation of resonance frequency of a coaxial feed C-slotted Microstrip Antenna. The Multi-Layer Perceptron Feed forward back Propagation (MLPFFBP) and Radial basis function Artificial Neural Network (RBFANN) have been used to implement the neural network model. A relative performance analysis of the proposed neural network for different training algorithms. Number of neurons and number of hidden layer is also carried out for estimating the resonance frequency. The method of moment (MOM) based IE3D software was used to generate data dictionary for training and validation set of ANN. The results obtain using ANN are compared with simulation feeding and found quite satisfactory and also it is concluded that RBFANN network is more accurate and fast compared to MLPFFBP network algorithm. Index Terms: Artificial Neural Network, C slot, Microstrip Antenna, Multilayer Feed Forward Networks, Radial basis function Artificial Neural Network, Resonance frequency.
FAULTY NODE RECOVERY AND REPLACEMENT ALGORITHM FOR WIRELESS SENSOR NETWORKFprj_publication
This paper proposes an algorithm by combining grade diffusion and genetic algorithm
to enhance the lifetime of a wireless sensor network. The algorithm is named as Fault Node
Recovery and Replacement algorithm. The algorithm enhances the lifetime of the wireless
sensor network with fewer replacements of sensor nodes. In the simulation it is shown that
the proposed algorithm increases the number of active node, reduces the rate of data loss,
increases the life time of the wireless sensor network and reduces the rate of energy
consumption.
E NERGY D EGREE D ISTANCE C LUSTERING A LGORITHM FOR W Snsijwmn
Energy consumption is an important parameter in th
e context of the wireless sensor networks (WSNs).
Several factors can cause energy over consumption s
uch as mobility, node position (relay or gateway),
retransmissions... In this paper, we described a ne
w Energy-Degree Distance(EDD) Clustering Algorithm
for the WSNs. A node with higher residual energy,
higher degree and closer to the base station is mor
e
likely elected as a clusterhead (CH). The inter clu
ster and intra cluster communications are realized
on one
hop. The principal goal of our algorithm is to min
imize the energy consumption and balance energy
consumption among all nodes. By comparing EDD clust
ering algorithm with LEACH algorithm,
simulation results have shown its effectiveness i
n saving energy
A study of localized algorithm for self organized wireless sensor network and...eSAT Journals
Abstract Communication between two nodes is a big issue in now days. To achieve that, wireless network plays a big role. With limited source of energy, memory & computation power wireless sensor networks can be composed by mass number of sensor nodes. Where the sensors’ lifetime depend on energies. Like autonomous system in LAN, cluster can be defined for wireless sensor network, where cluster head plays the prime role for the energy conservation. So, the optimization of cluster head within cluster along with number of nodes is a big research issue. Here I have analyzed the advanced optimization algorithm for sensor network clustering theoretically. I have tried to test the proposed method as a clustering algorithm and compared it with other recent sensor network clustering algorithm named Algorithm for Cluster Establishment (ACE) Index Terms: ACE; Data sets; Localized algorithm; Migration; Spawning threshold function
A study of localized algorithm for self organized wireless sensor network and...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
Enhancement of Improved Balanced LEACH for Heterogeneous Wireless Sensor Netw...acijjournal
Wireless sensor networks consists of thousands of tiny, low cost, low power and multifunctional sensor nodes where each sensor node has very low battery life. Purpose is to conserve the transmitted energy
from various sensor nodes. Various energy efficient algorithms have been designed for this. LEACH uses
distributed cluster formation & randomized rotation of the cluster head to minimize the network energy
consumption. Our paper is proposing an algorithm which is the enhancement of existing IB-LEACH. It reduces the energy consumption by using energy bank. This energy bank stores the energy after each round in both routing and clustering phase which overall increases the life time of the network. In this
approach, ACTIVE_ROUTE_TIMEOUT is also enhanced by shamming the static parameters of HELLO_INTERVAL, RREQ_RETRIES and NET_DIAMETER. Results are compared through MATLAB and provide better approach than previous ones.
ENERGY EFFICIENCY OF MIMO COOPERATIVE NETWORKS WITH ENERGY HARVESTING SENSOR ...ijasuc
This paper addresses the maximizing network lifetime problem in wireless sensor networks (WSNs) taking
into account the total Symbol Error rate (SER) at destination. Therefore, efficient power management is
needed for extend network lifetime. Our approach consists to provide the optimal transmission power
using the orthogonal multiple access channels between each sensor. In order to deeply study the
properties of our approach, firstly, the simple case is considered; the information sensed by the source
node passes by a single relay before reaching the destination node. Secondly, global case is studied; the
information passes by several relays. We consider, in the previous both cases, that the batteries are nonrechargeable. Thirdly, we spread our work the case where the batteries are rechargeable with unlimited
storage capacity. In all three cases, we suppose that Maximum Ratio Combining (MRC) is used as a
detector, and Amplify and Forward (AF) as a relaying strategy. Simulation results show the viability of
our approach which the network lifetime is extended of more than 70.72%when the batteries are non
rechargeable and 100.51% when the batteries are rechargeable in comparison with other traditional
method.
ENERGY EFFICIENCY OF MIMO COOPERATIVE NETWORKS WITH ENERGY HARVESTING SENSOR ...ijasuc
This paper addresses the maximizing network lifetime problem in wireless sensor networks (WSNs) taking
into account the total Symbol Error rate (SER) at destination. Therefore, efficient power management is
needed for extend network lifetime. Our approach consists to provide the optimal transmission power
using the orthogonal multiple access channels between each sensor. In order to deeply study the
properties of our approach, firstly, the simple case is considered; the information sensed by the source
node passes by a single relay before reaching the destination node. Secondly, global case is studied; the
information passes by several relays. We consider, in the previous both cases, that the batteries are nonrechargeable. Thirdly, we spread our work the case where the batteries are rechargeable with unlimited
storage capacity. In all three cases, we suppose that Maximum Ratio Combining (MRC) is used as a
detector, and Amplify and Forward (AF) as a relaying strategy. Simulation results show the viability of
our approach which the network lifetime is extended of more than 70.72%when the batteries are non
rechargeable and 100.51% when the batteries are rechargeable in comparison with other traditional
method.
ENERGY CONSUMPTION IMPROVEMENT OF TRADITIONAL CLUSTERING METHOD IN WIRELESS S...IJCNCJournal
In the traditional clustering routing protocol of wireless sensor network, LEACH protocol (Low Energy
Adaptive Clustering Hierarchy) is considered to have many outstanding advantages in the implementation
of the hierarchy according to low energy adaptive cluster to collect and distribute the data to the base
station. The main objective of LEACH is: To prolong life time of the network, reduce the energy
consumption by each node, using the data concentration to reduce bulletins in the network. However, in the
case of large network, the distance from the nodes to the base station is very different. Therefore, the
energy consumption when becoming the host node is very different but LEACH is not based on the
remaining energy to choose the host node, which is based on the number of times to become the host node
in the previous rounds. This makes the nodes far away from the base station lose power sooner.
In this paper, we give a new routing protocol based on the LEACH protocol in order to improve operating
time of sensor network by considering energy issues and distance in selecting the cluster-head (CH), at that
time the nodes with high energy and near the base station (BS) will have a greater probability of becoming
the cluster-head than the those in far and with lower energy.
Wireless sensor network are emerging in various fields like environmental monitoring, mining, surveillance
system, medical monitoring. LEACH protocol is one of the predominantly used clustering routing protocols
in wireless sensor networks. In Leach each node has equal chance to become a cluster head which make
the energy dissipated of each node be moderately balanced. We have pioneered an improved algorithm
named as Novel Leach based on Leach protocol. The proposed algorithm shows the significant
improvement in network lifetime .Comparison of proposed algorithm is done with basic leach in terms of
network life time, cluster head selection, energy consumption, and data transmission to base station. The
simulation results shows that proposed algorithm can reduce network energy consumption and prolong
network life commendably. Simulation of our protocol is done with Matlab.
Similar to Efficient Broadcast Authentication with Highest Life Span in Wireless Sensor Networks (20)
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
CFD Simulation of By-pass Flow in a HRSG module by R&R Consult.pptxR&R Consult
CFD analysis is incredibly effective at solving mysteries and improving the performance of complex systems!
Here's a great example: At a large natural gas-fired power plant, where they use waste heat to generate steam and energy, they were puzzled that their boiler wasn't producing as much steam as expected.
R&R and Tetra Engineering Group Inc. were asked to solve the issue with reduced steam production.
An inspection had shown that a significant amount of hot flue gas was bypassing the boiler tubes, where the heat was supposed to be transferred.
R&R Consult conducted a CFD analysis, which revealed that 6.3% of the flue gas was bypassing the boiler tubes without transferring heat. The analysis also showed that the flue gas was instead being directed along the sides of the boiler and between the modules that were supposed to capture the heat. This was the cause of the reduced performance.
Based on our results, Tetra Engineering installed covering plates to reduce the bypass flow. This improved the boiler's performance and increased electricity production.
It is always satisfying when we can help solve complex challenges like this. Do your systems also need a check-up or optimization? Give us a call!
Work done in cooperation with James Malloy and David Moelling from Tetra Engineering.
More examples of our work https://www.r-r-consult.dk/en/cases-en/
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.