This document discusses the effects of heat input and shielding gas composition on the microstructure, mechanical properties, and impact toughness of austenitic stainless steel 304L welds. Gas tungsten arc welding was used to weld samples with varying heat inputs and shielding gases of pure argon or a mixture of 98% argon and 2% nitrogen. Microstructural analysis found that higher heat input resulted in larger dendrite sizes in the weld metal. Using a nitrogen-containing shielding gas also refined the dendrites compared to pure argon. Properties testing showed that higher strength and hardness were achieved at lower heat inputs and when using the nitrogen-containing gas.
In this work, effect of welding electrode, welding current and corrosion media on
corrosion behaviour of three kinds of stainless steel (AISI 304, AISI 316 and AISI 410)
was investigated. Welding was performed by manual metal arc welding process using
three types of welding electrode (E308L, E316L and E310). Corrosion behaviour of
the welded joints was examined in two chloride mediums (3.5%NaCl and 3.5%KCl).
The results showed that welding electrodes E316L and E310, which contain Mo and
Ni respectively, increase corrosion resistance in of the weldment. The increment in
heat input by increasing welding current caused reduction in corrosion resistance by
facilitating carbon diffusion and formation of chromium carbides in the weld area. It
was also found that corrosion rate of 3.5% NaCl was more aggressive than 3.5% KCl.
In this work, effect of welding electrode, welding current and corrosion media on
corrosion behaviour of three kinds of stainless steel (AISI 304, AISI 316 and AISI 410)
was investigated. Welding was performed by manual metal arc welding process using
three types of welding electrode (E308L, E316L and E310). Corrosion behaviour of
the welded joints was examined in two chloride mediums (3.5%NaCl and 3.5%KCl).
The results showed that welding electrodes E316L and E310, which contain Mo and
Ni respectively, increase corrosion resistance in of the weldment. The increment in
heat input by increasing welding current caused reduction in corrosion resistance by
facilitating carbon diffusion and formation of chromium carbides in the weld area. It
was also found that corrosion rate of 3.5% NaCl was more aggressive than 3.5% KCl.
Development of dual phase steel and determination its of mechanical propertiesIAEME Publication
In this paper, the development of dual phase steel from low carbon steel and mechanical
properties have been studies. Dual phase steel is developed by intercritical annealing in order to
improve the hardness and impact toughness. Low carbon steel of 0.21% carbon content is first
intercritically heated in furnace and then rapid cooling in water is done to obtain the martensitic
steels. Different samples of DP steels are prepared by the intercritical annealing process temperature
ranging from740˚C to 840˚C. The heating temperature and different time of heating of the steel is
used to make different percentage of Maternsite steel. Dual phase steel so obtained is now tested and
properties of the DP steel are evaluated. Hardness, charpy, microstructure test for each specimen is
conducted to compare its hardness and toughness with low carbon steel. The mechanical properties
of heat treated and non heat treated specimens are obtained and compared. The result indicates that
the specimen hardness and toughness are proportional to amount of martensite and amount of
martensite depends on intercritical annealing temperature.
Since so many years a problem occurs in KSB Pump Va mbori for casting process i.e. cracks occurs in the castings & it is repeated one. Therefore the compan y has given opportunity to me to solve this problem . In case of steel casting there are mainly cracks & also blo w holes induced due to the casting procedure. There are many factors for the casting defects .The factor is unev en material feeding in casting & also due to the mo uld material & also the core material. These cracks finally brea k directly the component of the casting i.e. in cas e of pump the casting component is like Impeller,Volute casing & casing cover. At the time of feeding of steel material in to the casting the material is in liquid us form i.e. it i s hot material & this material is feeding into casting at the time o f feeding it develop different region of heat. At o ne side the temp is high &at other side the temp is low this also pr oduce cracks. To simulate that casting we use the M AGMA SOFTWARE for simulation & validate it using NDT.
Remaining life assessment of refinery furnace tubes using finite element methodBarhm Mohamad
Crude oil heater 9Cre-1Mo steel tubes from a refinery plant were studied, after 5 years of service at nominally 650 Cº and 3 bar, to predict their remnant lives. The investigation included dimensional, hardness and tensile measurements in addition to accelerated stress rupture tests between 650 Cº and 700 Cº and microstructural examination. Tube specimens were taken from two sections, the overheated side and the side which only saw the nominal operating temperature. The method employed involved the prediction of the increase in temperature with increasing sediment deposition during the operating life times using an FEM model. In addition the predicted temperatures are used to derive appropriate creep properties at relevant temperatures in a 3D pipe FEM creep analysis to predict the pipe deformation rate. All compare well with the actual service exposed pipe measurements and layer deposition. The overheated side revealed a small loss of creep strength in a stress rupture test. A layer of sediment (appr. 10 mm thickness) consisting basically of sintered carbon (coke) spread over the inside of the tube was acting as a thermal barrier causing the temperature to rise above 650 Cº. Analysis for the overheated side predicted an upper bound temperature of 800 Cº and a life of about 50 h suggesting that failure by creep rupture could occur rapidly in the sediment region.
Corrosion fatigue crack growth experiment was conducted on ESE(T) (Eccentrically-loaded Single Edge notch Tension) specimen made of IS 2062 steel in salt water environment. The specimen was placed in a transparent chamber made of perspex sheet containing 3.5% NaCl solution which acted as corrosion environment. The corrosion process was accelerated by applying constant direct current of 0.2 A which was supplied by means of a regulated power supply. The test was conducted using a ±250 kN capacity computer controlled servo-hydraulic fatigue rated Universal Testing Machine. The maximum and minimum load values were 15 kN and 1.5 kN. The test frequency was 0.375 Hz and the stress ratio was 0.1. Number of cycles to crack initiation was determined. Crack growth data were recorded at regular intervals. Crack growth curves were plotted and material constants C and m were found. Analytical studies were carried out and the results were compared with experimental results. Details of the analytical and experimental studies and the results are presented in this paper.
VOLUME-7 ISSUE-8, AUGUST 2019 , International Journal of Research in Advent Technology (IJRAT) , ISSN: 2321-9637 (Online) Published By: MG Aricent Pvt Ltd
The present research work demonstrates the
preparation of Copper Oxide Nanoparticles (CuO NPs) and
investigates the thermo mechanical properties of the CuO NPs
embedded in the polymer composites experimentally. In this study,
CuO NPs were produced by aqueous precipitation method and
morphology of the NPs was studied using Field Emission
Transmission Electron Microscope (FESEM). Epoxy resin and glass microsphere were considered the base material for the preparation of
the Nano based polymer composites. In order to fabricate the Nano
based polymer composites, CuO NPs with 1.0wtpercentage were
embedded in the base material by means of compression moulding
press. Nano composites proved higher thermal conductivity
enhancement rather than the base material. While comparing to the
base material, the maximum four-point bending strength of 415 MPa
was obtained from the Nano based polymer composites. The test
results obtained from the TG study revealed that an addition of CuO
NPs had acted as the thermal retardant and CuO NPs had delayed
thermal degradation of the Nano based polymer composites. Based
on the test results, it can be suggested that the newly fabricated
nanocomposites have achieved the improved thermal and mechanical
properties.
Mechanism of Fracture in Friction Stir Processed Aluminium AlloyDr. Amarjeet Singh
Aluminium alloys are used for important
applications in reducing the weight of the component and
structure particularly associated with transport, marine,
and aerospace fields. Grain refinement by scandium (Sc)
addition can eliminate the casting defects and increase the
resistance to hot tearing for high strength aluminium alloys.
FSP for cast aluminium alloys have been focused and it has
great advantages including solid state microstructural
evolution, altering mechanical properties by optimizing
process parameters. These parameters are tool rotational
speeds (720, and 1000 rpm), traverse speeds (80, and 70
mm/min), and axial compressive force at 15 kN, etc. The
mechanical properties had been evaluated on FSPed
aluminium alloy with different microstructural conditions.
Fracture properties of aluminium alloys are very important
for industrial applications. Tensile and fracture toughness
properties were correlated to microstructural and
fractographic features of the aluminium alloys need to
explore their essential failure mechanisms.
Development of dual phase steel and determination its of mechanical propertiesIAEME Publication
In this paper, the development of dual phase steel from low carbon steel and mechanical
properties have been studies. Dual phase steel is developed by intercritical annealing in order to
improve the hardness and impact toughness. Low carbon steel of 0.21% carbon content is first
intercritically heated in furnace and then rapid cooling in water is done to obtain the martensitic
steels. Different samples of DP steels are prepared by the intercritical annealing process temperature
ranging from740˚C to 840˚C. The heating temperature and different time of heating of the steel is
used to make different percentage of Maternsite steel. Dual phase steel so obtained is now tested and
properties of the DP steel are evaluated. Hardness, charpy, microstructure test for each specimen is
conducted to compare its hardness and toughness with low carbon steel. The mechanical properties
of heat treated and non heat treated specimens are obtained and compared. The result indicates that
the specimen hardness and toughness are proportional to amount of martensite and amount of
martensite depends on intercritical annealing temperature.
Since so many years a problem occurs in KSB Pump Va mbori for casting process i.e. cracks occurs in the castings & it is repeated one. Therefore the compan y has given opportunity to me to solve this problem . In case of steel casting there are mainly cracks & also blo w holes induced due to the casting procedure. There are many factors for the casting defects .The factor is unev en material feeding in casting & also due to the mo uld material & also the core material. These cracks finally brea k directly the component of the casting i.e. in cas e of pump the casting component is like Impeller,Volute casing & casing cover. At the time of feeding of steel material in to the casting the material is in liquid us form i.e. it i s hot material & this material is feeding into casting at the time o f feeding it develop different region of heat. At o ne side the temp is high &at other side the temp is low this also pr oduce cracks. To simulate that casting we use the M AGMA SOFTWARE for simulation & validate it using NDT.
Remaining life assessment of refinery furnace tubes using finite element methodBarhm Mohamad
Crude oil heater 9Cre-1Mo steel tubes from a refinery plant were studied, after 5 years of service at nominally 650 Cº and 3 bar, to predict their remnant lives. The investigation included dimensional, hardness and tensile measurements in addition to accelerated stress rupture tests between 650 Cº and 700 Cº and microstructural examination. Tube specimens were taken from two sections, the overheated side and the side which only saw the nominal operating temperature. The method employed involved the prediction of the increase in temperature with increasing sediment deposition during the operating life times using an FEM model. In addition the predicted temperatures are used to derive appropriate creep properties at relevant temperatures in a 3D pipe FEM creep analysis to predict the pipe deformation rate. All compare well with the actual service exposed pipe measurements and layer deposition. The overheated side revealed a small loss of creep strength in a stress rupture test. A layer of sediment (appr. 10 mm thickness) consisting basically of sintered carbon (coke) spread over the inside of the tube was acting as a thermal barrier causing the temperature to rise above 650 Cº. Analysis for the overheated side predicted an upper bound temperature of 800 Cº and a life of about 50 h suggesting that failure by creep rupture could occur rapidly in the sediment region.
Corrosion fatigue crack growth experiment was conducted on ESE(T) (Eccentrically-loaded Single Edge notch Tension) specimen made of IS 2062 steel in salt water environment. The specimen was placed in a transparent chamber made of perspex sheet containing 3.5% NaCl solution which acted as corrosion environment. The corrosion process was accelerated by applying constant direct current of 0.2 A which was supplied by means of a regulated power supply. The test was conducted using a ±250 kN capacity computer controlled servo-hydraulic fatigue rated Universal Testing Machine. The maximum and minimum load values were 15 kN and 1.5 kN. The test frequency was 0.375 Hz and the stress ratio was 0.1. Number of cycles to crack initiation was determined. Crack growth data were recorded at regular intervals. Crack growth curves were plotted and material constants C and m were found. Analytical studies were carried out and the results were compared with experimental results. Details of the analytical and experimental studies and the results are presented in this paper.
VOLUME-7 ISSUE-8, AUGUST 2019 , International Journal of Research in Advent Technology (IJRAT) , ISSN: 2321-9637 (Online) Published By: MG Aricent Pvt Ltd
The present research work demonstrates the
preparation of Copper Oxide Nanoparticles (CuO NPs) and
investigates the thermo mechanical properties of the CuO NPs
embedded in the polymer composites experimentally. In this study,
CuO NPs were produced by aqueous precipitation method and
morphology of the NPs was studied using Field Emission
Transmission Electron Microscope (FESEM). Epoxy resin and glass microsphere were considered the base material for the preparation of
the Nano based polymer composites. In order to fabricate the Nano
based polymer composites, CuO NPs with 1.0wtpercentage were
embedded in the base material by means of compression moulding
press. Nano composites proved higher thermal conductivity
enhancement rather than the base material. While comparing to the
base material, the maximum four-point bending strength of 415 MPa
was obtained from the Nano based polymer composites. The test
results obtained from the TG study revealed that an addition of CuO
NPs had acted as the thermal retardant and CuO NPs had delayed
thermal degradation of the Nano based polymer composites. Based
on the test results, it can be suggested that the newly fabricated
nanocomposites have achieved the improved thermal and mechanical
properties.
Mechanism of Fracture in Friction Stir Processed Aluminium AlloyDr. Amarjeet Singh
Aluminium alloys are used for important
applications in reducing the weight of the component and
structure particularly associated with transport, marine,
and aerospace fields. Grain refinement by scandium (Sc)
addition can eliminate the casting defects and increase the
resistance to hot tearing for high strength aluminium alloys.
FSP for cast aluminium alloys have been focused and it has
great advantages including solid state microstructural
evolution, altering mechanical properties by optimizing
process parameters. These parameters are tool rotational
speeds (720, and 1000 rpm), traverse speeds (80, and 70
mm/min), and axial compressive force at 15 kN, etc. The
mechanical properties had been evaluated on FSPed
aluminium alloy with different microstructural conditions.
Fracture properties of aluminium alloys are very important
for industrial applications. Tensile and fracture toughness
properties were correlated to microstructural and
fractographic features of the aluminium alloys need to
explore their essential failure mechanisms.
EVALUATION OF PROCESSES PARAMETER AND MECHANICAL PROPERTIES IN FRICTION STIR ...IAEME Publication
The present study focuses on Friction Stir Welding of steel being very popular due to the vast application in the fields of automotive and ship building industries. The main constrained of welding steel has considered due to severe loads and temperatures at the interface of FSW tool and parent materials. Ti and pcBN based alloys are suitable for joining steel alloys up to 15 mm thick was found during study. Many researchers carried out study on FSW of steel and found on weld process parameters, mechanical properties, microstructure and the tool employed to produce the weld. It was found that carbon content, welding speed as well as the rotational speed affects between the mechanical properties and the microstructure of the weld.
Duplex 2209 Weld Overlay by ESSC ProcessIJERA Editor
In the modern world of industrialization the wear is eating metal assets worth millions of dollars per year. The wear is in the form of corrosion, erosion, abrasion etc. which occur in the process industries like oil & gas, refineries, cement plants, steel plants, shipping and offshore working structures. The equipments like pressure vessels, heat exchangers, hydro processing reactors which very often work at elevated temperatures face corrosion in the internal diameter. Duplex 2209 weld overlay on ferrous material is developed for high corrosion resistance properties and having high productivity by Electroslag strip cladding process due to its less dilution ~10% as compared to SMAW , GTAW or FCAW process. Because of Low Dilution ~10% undiluted chemistry can be achieved with single layer as compared to other weld overlay processes. The facility was developed inhouse to carry out weld overlay by ESSC and Testing.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Machining challenges in stainless steel – a reviewIJARIIT
In today’s world AISI Stainless Steel contributes to almost half of the world’s production and consumption
for industrial purposes. Stainless Steel is most popular alloy widely used in part manufacturing due to its inherent
properties like high strength, great corrosion resistant, high ductility etc. but are hard materials to machining on base
performance criteria like metallurgical aspect, low thermal conductivity, chip formation, cutting tool wear and surface
integrity. The surface roughness and material removal rate have been identified as quality attributes and are assumed
to be directly related to performance, productivity, and production costs. In this paper study of various machining
problem discussed by different researchers and their probable solution, which helps to reduce tool wear, increase
corrosion resistance, high surface finish by reducing machining complexity.
Effect of Powder Mixed Dielectric Fluid on MRR And SR During Electrical Disch...IJERDJOURNAL
ABSTRACT: This paper mainly focussed to investigate the machining characteristics of RENE 80 Nickel Alloy during powder mixed electrical discharge machining. The experiments were conducted considering electrical parameters (pulse on time, peak current and pulse off time) at optimal combination to get maximum material removal rate by varying powders like aluminium, graphite and combination of aluminium and graphite powders and their concentrations. The experimental results reveal that improvement in material removal rate with addition of powders into dielectric fluid. The maximum material removal rate (75.08 mm3 /min) was noticed with graphite powder substances at 9 g/l. Minimum surface roughness (4.44µm) was noticed at the combination of aluminium and graphite powders (1:1 ratio) substance of 4.5 g/l. However considering simultaneously better values of all two responses namely material removal rate (71.90 mm3 /min) and surface roughness (4.44µm) are obtained with the combination of aluminium and graphite powders (1:1 ratio) of 4.5 g/l.
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
CFD Simulation of By-pass Flow in a HRSG module by R&R Consult.pptxR&R Consult
CFD analysis is incredibly effective at solving mysteries and improving the performance of complex systems!
Here's a great example: At a large natural gas-fired power plant, where they use waste heat to generate steam and energy, they were puzzled that their boiler wasn't producing as much steam as expected.
R&R and Tetra Engineering Group Inc. were asked to solve the issue with reduced steam production.
An inspection had shown that a significant amount of hot flue gas was bypassing the boiler tubes, where the heat was supposed to be transferred.
R&R Consult conducted a CFD analysis, which revealed that 6.3% of the flue gas was bypassing the boiler tubes without transferring heat. The analysis also showed that the flue gas was instead being directed along the sides of the boiler and between the modules that were supposed to capture the heat. This was the cause of the reduced performance.
Based on our results, Tetra Engineering installed covering plates to reduce the bypass flow. This improved the boiler's performance and increased electricity production.
It is always satisfying when we can help solve complex challenges like this. Do your systems also need a check-up or optimization? Give us a call!
Work done in cooperation with James Malloy and David Moelling from Tetra Engineering.
More examples of our work https://www.r-r-consult.dk/en/cases-en/