This document discusses different types of electrical loads and wiring systems. It describes domestic, commercial, street light, agricultural, industrial, and other loads. It also outlines overhead and underground supply systems. Several wiring systems are covered, including cleat, casing capping, CTS, metal sheathed, and conduit wiring. Each system is described and their advantages and disadvantages are provided. The document provides information on selecting wiring systems based on factors like durability, appearance, cost, safety, and maintenance.

1. Design Considerations Of Electrical Installations

2. Types of Loads
• Domestic Purpose
The electricity for domestic purpose is consumed in various types
of loads such as:
(1)Single phase 5 A domestic Lighting load:
-For lighting Filament lamps , fluorescent tubes , fans.
(2)Single phase 15 A power domestic load:
-In case of air conditioning , electric water heating , refrigeration.
(3)Commercial load:
(i)Shops (ii)Offices (iii)Schools (iv)Colleges

3. (4)Street light load : This is under Gram-Panchayat ;Municipality or
corporation . A separate line is provided for this purpose
and is charged in a different type of tariff.
(5)Agricultural load :This is generally 3 phase 440 volts ,pumping motor load.
(6)Rice mills /Saw mills : For this a 3 phase 440 volt 3-phase service line is
separately provided.
(7)Industrial load: (a)For small scale industries / workshops
(b)For medium scale industries
(c)Large scale industries

4. Electric supply system
• Electricity is supplied as per the requirements.
• Generally electrical supply is given by a 3 phase 4 wire system.The
distributor lines from the poles are run in the different areas where
electricity is needed.
• Types of supply system:
(1)Overhead supply system.
(2)Underground cable system.

5. Selection of type of wiring
• The type of the wiring system depends upon the following factors:-
(1)Durability
(2)Appearance
(3)Cost
(4)Safety
(5)Accessibility
(6)Maintenance cost

6. (1)Durability:-The type of wiring selected for a premises should be durable.
(2)Appearance:-The appearance of the wiring should be such that it should not
spoil the beauty of premises.
(3)Cost:-It is most important factor deciding the type of wiring system to be
used.
(4)Safety:-This is also a most important factor deciding type of wiring to be
provided.
(5)Accessibility:-The type of wiring selected should be such that the extension
or renewal of wiring should be possible.

7. System of wiring
• The following are the wiring systems in common use:
(1)Cleat wiring
(2)Casing capping
(3)C.T.S or T.R.S wiring system
(4)Metal sheathed wiring system
(5)Conduit wiring system

8. Cleat Wiring

9. • In this type of wiring, insulated conductors (usually VIR, Vulcanized Indian Rubber) are
supported on porcelain or wooden cleats.
• The cleats have two halves one base and the other cap. The cables are placed in the
grooves provided in the base and then the cap is placed. Both are fixed securely on the
walls by 40mm long screws.
Advantages:
• Easy installation
• Materials can be retrieved for reuse
• Flexibility provided for inspection, modifications and expansion.
• Relatively economical
• Skilled manpower not required.
Disadvantages:
• Appearance is not good
• Open system of wiring requiring regular cleaning
• Higher risk of mechanical injury.

10. Casing capping

11. • It consists of insulated conductors laid inside rectangular, teakwood or PVC boxes
having grooves inside it.
• A rectangular strip of wood called capping having same width as that of casing is fixed
over it. Both the casing and the capping are screwed together at every 15 cms.
Advantages:
• Cheaper than lead sheathed and conduit wiring.
• Provides good isolation as the conductors are placed apart reducing the risk of short circuit.
• Easily accessible for inspection and repairs.
• Since the wires are not exposed to atmosphere, insulation is less affected by dust, dirt and
climatic variations.
Disadvantages:
• Highly inflammable.
• Usage of unseasoned wood gets damaged by termites.
• Skilled workmanship required.

12. C.T.S or T.R.S wiring system

13. • In this wiring system, wires sheathed in tough rubber are used which are quite flexible.
They are clipped on wooden battens with brass clips (link or joint) and fixed on to the walls
or ceilings by flat head screws. These cables are moisture and chemical proof.
Advantages:
• Easy installation and is durable
• Lower risk of short circuit.
• Cheaper than casing and capping system of wiring
• Gives a good appearance if properly erected.
Disadvantages:
• Danger of mechanical injury.
• Danger of fire hazard.
• Should not be exposed to direct sunlight.
• Skilled workmen are required.

14. Metal sheathed wiring system

15. • The wiring is similar to that of CTS but the conductors (two or three) are individually
insulated and covered with a common outer lead-aluminum alloy sheath. The sheath
protects the cable against dampness, atmospheric extremities and mechanical damages.
Advantages:
• Easy installation and is aesthetic in appearance
• Highly durable
• Suitable in adverse climatic conditions provided the joints are not exposed
Disadvantages:
• Requires skilled labor
• Very expensive
• Unsuitable for chemical industries

16. Conduit wiring system

17. • In this system PVC (polyvinyl chloride) or VIR cables are run through metallic or PVC
pipes providing good protection against mechanical injury and fire due to short circuit.
Advantages
• No risk of fire and good protection against mechanical injury.
• The lead and return wires can be carried in the same tube.
• Earthing and continuity is assured.
• Waterproof and trouble shooting is easy.
• Shock- proof with proper earthing and bonding
Disadvantages
• Very expensive system of wiring.
• Requires good skilled workmanship.