This document is a project report submitted by Jitesh Kumar for the partial fulfillment of a Master's degree in Mechanical Engineering. It discusses the design and fabrication of a working model of an Abrasive Jet Machine. The report includes sections on the components of an AJM, variables that influence the machining process, advantages and limitations, applications, and a literature review. It also provides details on the design of the major components of the machine being developed for this project.
These slide gives overall welding process and gives the tips about the robotic welding process and then adaptability with the industrial welding robotic coordinates.
These slide gives overall welding process and gives the tips about the robotic welding process and then adaptability with the industrial welding robotic coordinates.
The following presentation contains facts about how abrasives are used in water jet cutting. It also provides information about the largest garnet abrasive manufacturers and exporters in India, like VV Mineral. They are the first private ilmenite exporters of India. VV Minerals India has a huge market share in Europe, Middle East, East Asia, Australia and USA. They are based in Tamil Nadu and the company is owned by Mr. S. Vaikundarajan.
Informe Técnico de la localización para el proyecto de las oficinas del Gobie...Alejandro Crespo Kashtanov
Informe técnico interno del Gobierno Municipal calificando de INVIABLE la localización del complejo administrativo "Quinta Municipal" a razón del cambio de uso de suelo de un área verde, lo cual contravendría el Art.129 de la Ley 2028 (Ley de Municipalidades).
Experimental Analysis & Optimization of Cylindirical Grinding Process Paramet...IJERA Editor
As per the modern Industrial requirements, higher surface finish mechanical components and mating parts with close limits and tolerances, is one of the most important requirement. Abrasive machining processes are generally the last operations performed on manufactured products for higher surface finishing and for fine or small scale material removal. Higher surface finish and high rate of removal can be obtained if a large number of grains act together. This is accomplished by using bonded abrasives as in grinding wheel or by modern machining processes. In the present study, Taguchi method or Design of experiments has been used to optimize the effect of cylindrical grinding parameters such as wheel speed (rpm), work speed, feed (mm/min.), depth of cut and cutting fluid on the surface roughness of EN15AM steel. Ground surface roughness measurements were carried out by Talysurf surface roughness tester. EN15AM steel has several industrial applications in manufacturing of engine shafts, connecting rods, spindles, studs, bolt, screws etc. The results indicated that grinding wheel speed, work piece speed, table feed rate and depth of cut were the significant factors for the surface roughness and material removal rate. Surface roughness is minimum at 2000 r.p.m. of grinding wheel speed , work piece speed 80 rpm, feed rate 275 mm/min. and 0.06 mm depth of cut.
Advance machining processes are used where higher accuracy and surface finish is required. One of them, Abrasive jet machining is a non-traditional machining process in which a high-pressure air stream and abrasive particles impinge on a work surface through a nozzle. Abrasive jet machining (AJM) removes material through the action of a focused beam of abrasive jet directed at the workpiece the resulting erosion can be used for cutting, drilling and debarring etc. With the increase of needs for machining of ceramics, semiconductors, electronic devices and L.C.D., AJM has become a useful technique for micromachining. it is more useful in industries for precision work. Material removal rate during this process affected by different parameters like abrasive particle size, the velocity of abrasive flow rate, gas pressure, standoff distance etc.
Abrasive water jet review and parameter selection by AHP method.IOSR Journals
An Abrasive Water Jet is one of the most recently developed non-traditional manufacturing
processes. Abrasive water jet offers the potential for the development in cutting which is less sensitive to
material properties, has virtually no thermal effects, and imposes minimal stresses. As it is a cold process has
also important applications where heat-affected zones are to be avoided. In this work, a deep study of this newer
non-conventional technique of machining i.e., abrasive water jet machining is done. In this paper more focus is
on selection of various process parameters like-angle of impact, Pressure inside the pumping system, abrasive
material type, Stand-off distance, focusing tube diameter, nozzle speed, abrasive mass flow rate and target
material properties for getting the required output like- depth of cut and cut quality. For cutting Stainless steel
(Grade 304), important task is to find out a few parameters which influence more. With the help of Analytical
Hierarchy Process technique the selection of a few parameters are done which are comparatively more
influencing. Weighteges are given to parameters on the basis of previous study and experience of owner of the
company who is dealing with abrasive water jet technology since many years.
Effect of Process Parameters on Micro Hardness of Mild Steel Processed by Sur...IOSR Journals
Surface grinding process can be utilized to create flat shapes at a high production rate and low
cost.. In this investigation, indigenously designed set up were used for evaluating the surface grinding process
was established. An experimental investigation was carried out to study the effect of surface grinding process
parameters i.e. Inlet pressure of coolant, grinding wheel speed, work-piece speed, and nozzle angle on the micro
hardness of the mild steel specimen. In the present study Horizontal spindle and reciprocating table type
surface grinding machine fitted with test rig is used and cutting fluid is applied through the convergent nozzle to
throw the cutting fluids at the cutting zone. In order to evaluate the effect of selected process parameters, one
variable approach has been used in the present study. Plots of various Micro Hardness responses have been
used to determine the relationship between the output response and the input parameters. The value of
microhardness of grinded mild steel work-piece varies from 292.63 to 370.73 HV
IJERA (International journal of Engineering Research and Applications) is International online, ... peer reviewed journal. For more detail or submit your article, please visit www.ijera.com
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Experimental Analysis of Material Removal Rate in Drilling of 41Cr4 by a Tagu...IJERA Editor
In manufacturing industries the largest amount of money spent on drills. Therefore, from the viewpoint of cost and productivity, modeling and optimization of drilling processes parameter are extremely important for the manufacturing industry this paper presents a detailed model for drilling process parameter. The detailed structure includes in the model, are three parameters such as such as Spindle Speed, feed and depth of cut on material removal rate in drilling of 41 Cr 4 material using HSS spiral drill .We an effect of this three parameters on material removal rate .The detailed mathematical model is simulated by Minitab14 and simulation results fit experiment data very well In this investigation, an effective approach based on Taguchi method, analysis of variance (ANOVA), multivariable linear regression (MVLR), has been developed to determine the optimum conditions leading to higher MRR. Experiments were conducted by varying Spindle Speed, feed and depth of cut using L9 orthogonal array of Taguchi method. The present work aims at optimizing process parameters to achieve high MMR. Experimental results from the orthogonal array were used as the training data for the MVLR model to map the relationship between process parameters and MMR the experiment was conducted on drilling machine. From the investigation It concludes that speed is most influencing parameter followed by feed and depth of cut on MRR
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Similar to Design and fabrication of working model of abrasive jet machine (20)
Design and fabrication of working model of abrasive jet machine
1. DESIGN AND FABRICATION OF WORKING
MODEL OF ABRASIVE JET MACHINE
A PROJECT REPORT
Submitted by
JITESH KUMAR
(University Roll No. 100237682133)
In partial fulfillment for the aw
MASTER OF TECHNOLOGY
MECHANICAL ENGINEERING
PTU REGIONAL CENTRE
D.A.V INSTITUTE OF EN
award of the degree
of
IN
At
UTE ENGINEERING & TECHNOLOGY
JALANDHAR
DECEMBER 2012
1
GINEERING
2. 2
DECLARATION
I hereby declare that the project entitled “DESIGN AND FABRICATION OF
WORKING MODEL OF ABRASIVE JET MACHINE” submitted for the M
Tech. Degree is my original work and the project has not formed the basis for the
award of any degree, associate ship, fellowship or any other similar title.
Signature of the student
Place:
Date:
3. 3
CERTIFICATE
This is to certify that the project entitled “DESIGN AND FABRICATION OF
WORKING MODEL OF ABRASIVE JET MACHINE” is the bonafide work
carried out by JITESH KUMAR, student of M Tech (Part-time), Punjab
Technical University, Jalandhar, during the year 2012, in partial fulfillment of the
requirements for the award of the Degree of Master of Mechanical Engineering
and that the project has not formed the basis for the award previously of any
degree, diploma associate ship, fellowship or any other similar title.
Signature of the Guide
Place:
Date:
4. 4
AKNOWLEDGEMENT
I deem it a privilege to have been a student of Mechanical Engineering stream in
DAV Institute of Technology, Jalandhar. I take this opportunity to express my
gratitude to all those who motivated, encouraged and helped me in the project
work. I’m grateful to my supervisor, Mr. Gaurav Dhuria, for his kind support,
guidance and encouragement throughout the project work, also for introducing to
me this topic, which has been very interesting and has given us great insight to the
future work on this area. I would like to take the chance to express my appreciation
to HOD, Mechanical Department Dr. Amit Kohli to provide this opportunity.
Special thanks to other members of the department for being so supportive and
helpful in every possible way. I would like to express my appreciation to my
friends Mr. Lovepreet singh and Mr. Angrej Singh. Their continuous support gave
me the strength for pursuing my dream.
DAVIET Jalandhar Jitesh kumar
November 2012 Univ. Roll No. 100237682133
Department of Mechanical Engineering
DAVIET Jalandhar
5. 5
ABSTRACT
Abrasive Jet Machining (AJM) is the process of material removal from a work
piece by the application of a high speed stream of abrasive particles carried in a gas
or air medium from a nozzle. The material removal process is mainly by erosion.
The AJM will chiefly be used to cut shapes in hard and brittle materials like glass,
ceramics etc. the machine will be automated to have 3 axes travel. The different
components of AJM are Compressor, Vibrator, dehumidifier, Pressure Regulator,
and Dust filter, Nozzle, Pressure gauge etc. The different components are selected
after appropriate design calculations.
In this project, a model of the Abrasive Jet Machine is designed using available
hardware and software etc. taking into consideration of commercially available
components. Care has been taken to use less fabricated components rather than
directly procuring them, because, the lack of accuracy in fabricated components
would lead to a diminished performance of the machine.
6. 6
List of Figures
Fig. 1 Schematic layout of abrasive jet machine
Fig 2 Effect of process parameters on erosion rate
Fig 3 Crack propagation during abrasive cutting of glass
Fig. 4 Filter regulator unit
Fig. 5 Abrasive container
Fig. 6 Cam
Fig. 7 Vibration Assembly
Fig. 8 Cut section of Nozzle
Fig 9 Position of nozzle
List of Tables
Table 1 Characteristics of different variables
Table 2 Cost calculation
7. 7
Table of contents
CHAPTER No. TITLE PAGE No.
Title Page 1
Declaration of the student 2
Certificate of the Guide 3
Acknowledgement 4
Abstract 5
List of Figures and tables 6
1. CHAPTER ONE
1.1 Introduction 9
1.2 Equipments 9
1.3 Different variables in Abrasive jet machine. 12
1.4 Variable characteristics 13
1.5 Advantages 14
1.6 Limitations 14
1.7 Applications 15
2. CHAPTER TWO
2.1 Literature Review 16
8. 8
3. CHAPTER THREE
Components and their design
3.1 Compressor 19
3.2 FR Unit 19
3.3 Vibrating Unit 21
(i) Abrasive container
(ii) Cam
(iii) Induction Motor
3.4 Nozzle 25
4. CHAPTER FOUR
4.1 Total Assembly 26
5. CHAPTER FIVE
5.1 Cost estimation 27
• CONCLUSION 28
• REFRENCES 29
9. 9
1. CHAPTER ONE
1.1 Introduction
Abrasive Jet Machining (AJM) is the removal of material from a workpiece by the application of
a high speed stream of abrasive particles carried in gas medium from a nozzle. The AJM process
differs from conventional sand blasting in that the abrasive is much finer and the process
parameters and cutting action are carefully controlled.
The process is used chiefly to cut intricate shapes in hard and brittle materials which are sensitive
to heat and have a tendency to chip easily. The process is also used for deburring and cleaning
operations. AJM is inherently free from chatter and vibration problems. The cutting action is
cool because the carrier gas serves as a coolant.
1.2 Equipments
A schematic layout of AJM is shown in Fig‐1. The filtered gas, supplied under pressure to the
mixing chamber containing the abrasive powder and vibrating at 50 c/s, entrains the abrasive
particle and is the passed into a connecting hose. This abrasive and gas mixture emerges from a
small nozzle at high velocity. The abrasive powder feed rate is controlled by the amplitude of
vibration of the mixing chamber. A pressure regulator controls the gas flow and pressure.
The nozzle is mounted on a fixture. Either the workpiece or the nozzle is moved by cams
pantograph or other suitable mechanisms to control the size and shape of the cut. Hand operation
is sometimes adequate to remove surface contaminations or in cutting where accuracy is not very
critical. Dust removal equipment is necessary to protect the environment. Commercial bench
mounted units including all controls, motion producing devices, and dust control equipment are
available.
10. 10
Fig. 1 Schematic layout of abrasive jet machine
11. 11
The major components are:
1. Air compressor.
2. Air filter.
3. Dehumidifier.
4. Pressure Gauge.
5. Pressure Regulator.
6. Vibrator or Mixer.
7. Nozzle.
8. Arrangement to hold the work piece.
12. 12
1.3 Different variables in Abrasive Jet Machine:
The variables that influence the rate of metal removal and accuracy of machining in this process
is:
1. Carrier gas
2. Types of abrasive
3. Size of abrasive grain
4. Velocity of abrasive jet
5. Flow rate of abrasive
6. Work material
7. Geometry, composition and material of nozzle
8. Nozzle work distance (stand off distance)
13. 13
1.4 Characteristics of different Variables:
Medium Air , CO2 ,N2
Abrasive SiC, Al2O3 (of size 20μ to 50μ )
Flow rate of abrasive 3 to 20 gram/min
Velocity 150 to 300 m/min
Pressure 2 to 8 kg/cm2
Nozzle size 0.40 to 0.80 mm
Material of nozzle Tungsten carbide, Sapphire
Nozzle life 12 to 300 hr
Stand off distance 0.25 to 15 mm (8mm generally)
Work material Non Metals like glass, ceramics,
and granites.
Metals and alloys of hard materials
like germanium, silicon etc
Application Drilling, cutting, cleaning
Table 1 Characteristics of different variables
14. 14
1.4 Advantages:
1. Low capital cost
2. Ability to cut intricate holes shape in materials of any hardness.
3. Ability to cut heat sensitive material without damage.
4. As no heat is generated in the process, no change in microstructure
1.5 Limitations:
1. Material removal rate is low and hence its application is limited.
2. Embedding of the abrasive in the work piece surface may occur while machining softer
material.
3. The abrasive material may accumulate at nozzle and fail the process if moisture is present in
the air.
4. It cannot be used to drill blind holes.
5. Occasional plugging of mixing tube: Usually caused by dirt or large particles in abrasive.
6. Wear, misalignment, and damage to the nozzle.
15. 15
1.6 Application:
The major application of Abrasive jet machining process is in the machining of essentially
brittle materials and heat sensitive materials like glass, quartz, sapphire, semiconductor
materials, mica and ceramics. It is also used in cutting slot, thin sections, countering, drilling, for
producing integrate shapes in hard and brittle materials. It is often used for cleaning and
polishing of plastics nylon and Teflon components. Delicate cleaning, such as removal of
smudges from antique documents, is also easily done with Abrasive jet machining.
16. 16
CHAPTER TWO
2.1 Literature survey:
The literature study of Abrasive Jet Machine reveals that the Machining process was started a
few decades ago. Till date there has been a through and detailed experiment and theoretical study on
the process. Most of the studies argue over the hydrodynamic characteristics of abrasive jets, hence
ascertaining the influence of all operational variables on the process effectiveness including abrasive
type, size and concentration, impact speed and angle of impingement. Other papers found new
problems concerning carrier gas typologies, nozzle shape, size and wear, jet velocity and pressure,
stand‐off‐distance (SOD), or nozzle‐tip‐distance (NTD). These papers express the overall process
performance in terms of material removal rate, geometrical tolerances and surface finishing of work
pieces, as well as in terms of nozzle wear rate. Finally, there are several significant and important
papers which focus on either leading process mechanisms in machining of both ductile and brittle
materials, or on the development of systematic experimental‐statistical approaches and artificial
neural networks to predict the relationship between the settings of operational variables and the
machining rate and accuracy in surface finishing.
(Ref‐9)
The erosion of brittle materials by solid micro-particles is a complex process in
which material is removed from the target surface by brittle fractures. The rate of material
removal is one of the most important quantities for a machining process. Predictive mathematical
models for the erosion rates in micro-hole drilling and micro-channel cutting on glasses with an
abrasive air jet are developed. A dimensional analysis technique is used to formulate the models
as functions of the particle impact parameters, target material properties and the major process
parameters that are known to affect the erosion process of brittle materials. The effect of various
parameters like abrasive mass flow rate, air pressure and stand off distance on erosion rate is
shown by following graphical presentation.
17. 17
Fig 2 Effect of process parameters on erosion rate
18. 18
(Ref‐10)
The AJM has been applied to rough working such as deburring and rough finishing. With
the increase of the needs for machining of ceramics, semiconductors, electronic devices and
LCD’s, micro-AJM has become a useful technique for micro machining. Experimental results
showed good performance in micro-grooving of glass; however, the size of machined groove
increased about 2–4 μm. With the fine-tuning the compensation for film wear, micro-AJM could
be effectively applied to the micro-machining of semiconductors, electronic devices and LCD.
The crack propagation during impact of abrasive particles on machining material is given below:
Fig 3 Crack propagation during abrasive cutting of glass
19. 19
CHAPTER THREE
Components and their design
3.1 Compressor
Compressor is a device that converts power (usually from an electric motor, a diesel engine
or a gasoline engine) into kinetic energy by compressing and pressurizing air or gas which can be
released according to use. In this project, a reciprocating air compressor of 2kW is used to
produce compressed air up to the pressure of 150 psi and having storage tank which has storage
capacity of 50 liters.
3.2 FR Unit (Dehumidifier):
The FRL Unit (Air Filter Regulator Lubricator unit) which is otherwise called the moisture
separator or dehumidifier is required for separating the moisture from air. Atmospheric air
always contains some water vapors in it. As the air with high velocity is blown from the nozzle
there is an abrupt rise in pressure which converts water vapors into moisture. The moisture
makes the abrasive particles to agglomerate and this clogs the outlet of the Nozzle. To avoid this
clogging moisture separator should be used before abrasive particles are mixed with compressed
air. Different FRL Units are available commercially.
20. 20
Fig. 4 Filter regulator unit
INLET
OUTLET
Circulation of air
Separation of moisture
21. 21
3.3 The Vibrating Unit:
Vibrating Unit is used for mixing the air with the abrasive particles (Al2O3). The Abrasive
particles are stored in a container through which air is flown. The particles are agitated by means
of a cam and motor arrangement. The rotation of cam results in vibration in the abrasive
container. The flow rate of abrasive materials can be controlled by manipulating the rotational
speed of the motor. The abrasive container will have one inlet and one outlet for air passage and
will be vertically suspended from a hinged joint. So the Vibrating Unit consists of following
parts –
i. Abrasive container
ii. Cam
iii. Induction Motor
(i) Abrasive container
Outlet
Fig. 5 Abrasive container
Inlet
22. Abrasive container is fabricated by a hollow cylindrical thick metallic pipe of 60mm diameter
and 140mm height. Two circular pipes of internal diameter 18mm is dipped from the top and
welded, which would act as input for compressed air and output for mixture of compressed air
and abrasive particles. The length of input pipe dipped is kept long to uniform circulation of
compressed air into the container.
22
(ii) Cam
Cam is fixed with shaft of the induction motor. The profile of the cam is taken to be a
circular one. The distance between two centers as shown in fig‐26 is 5mm. When the motor
rotates; it makes the container to vibrate. Width of cam is 35mm.
Fig. 6 Cam
(iii) Induction Motor
Induction motor used in this project is Single phase AC Induction motor of 0.5 watt. This
motor is used to provide rotational motion to the Cam attached with it. The installed induction
motor has speed of 600 rpm.
25. 25
3.4 Nozzle
A standard high carbon high chromium cylindrical rod was cut into required length by
power hack‐saw. The external diameter was then brought to 20mm by turning it in lathe and then
the tip was made by tapering one end by the same lathe. A blind hole of approximate depth
25mm was made on the planner face of the rod by means of a 12mm drill bit in a drilling
machine. The end of the blind hole forms a shape of 118 degree taper because of the tool tip
angle. Internal threading was made by 12mm tap. Then the tip of the nozzle is diameter drilled to
approximate diameter of 1mm
Threaded
1 mm hole
Fig. 8 Cut section of Nozzle Fig 9 Position of nozzle
26. 26
CHAPTER FOUR
4.1 Total assembly:
Finally all parts are assembled with hose pipes and clamps. First of all compressor is joined with
FR unit which is acting as filter, dehumidifier and regulator. Then further FR is attached with the
abrasive container with pipes. Then from the output of abrasive container a pipe is attached to
the nozzle which will help to transport compressed air and abrasive mixture to the nozzle. Along
with it Induction motor is also attached to the cam and this assembly is provided to abrasive
container as given in the picture below:
27. 27
CHAPTER FIVE
5.1 Cost calculation:
S No. Name of Item Quantity Cost per unit Total cost of item
1. Reciprocating Air
compressor
1 8000 8000
2. FR unit 1 1200 1200
3. Abrasive container 1 400 400
4. Induction Motor 1 900 900
5. Abrasives 3 kg 50 150
6. Accessories - 2000 2000
7. Other expences - 1500 1500
TOTAL 14150
Table 2 Cost calculation
28. 28
CONCLUSION
In this project a complete design of the Abrasive Jet Machine is given. The total assembly is
designed taking in account of currently available components in the market. The designing and
assembling of very large number of components was a tremendous task and was completed on
time. However because of some parts couldn’t be purchased the whole assembly was limited to
some basic manufacturing operation.
The project can go beyond its current position and capabilities by employing automation into it.
This can be done by using stepper motors or DC servo motors interfaced with standard PCI
controllers or standalone controllers. 2‐D profiles can be converted into standard G‐codes and
M‐codes and that can be sent to the machine to perform automated machining.
29. 29
BIBLIOGRAPHY AND REFERENCES
Books
1. “Modern machining processes” by P C Pandey & H S Shan, The McGraw-Hill
companies.
2. “Production Technology” by R K Jain, Khanna Publications.
3. “Production Technology”, HMT Publications.
Websites
4. www.science direct .com.
5. www.apex.com
6. www.indiastudychannel.com
7. www.youtube.com
8. www.indiamart.com
Journals
9. “Modeling of erosion rate in micro abrasive air jet machining of glasses” by J M Fan, C
Y Wang, J Wang. Faculty of Electromechanical Engineering, Guangdong University of
Technology, Guangzhou 510006, China
10. Journal of material processing technology, Volume 146, 28 February 2004,
Page 234-240