Electric charge is a fundamental property of matter that causes electromagnetic attraction and repulsion. The electric charge is quantized, meaning it occurs in discrete integer multiples of the elementary charge carried by a single electron or proton. Robert Millikan's oil drop experiment directly demonstrated the quantization of charge by measuring the electric charges on tiny oil droplets, finding they were always integer multiples of approximately 1.6×10^-19 coulombs. Coulomb's law describes the electric force between two charged particles, stating it is directly proportional to the product of their charges and inversely proportional to the square of the distance between them.
An electric current is the rate of flow of electric charge past a point or region. An electric current is said to exist when there is a net flow of electric charge through a region. In electric circuits this charge is often carried by electrons moving through a wire. It can also be carried by ions in an electrolyte, or by both ions and electrons such as in an ionized gas (plasma).
As charges are of two types, positive and negative, there are other certain basic properties they follow. If the size of charged bodies is so small, we consider them as point charges. Copy the link given below and paste it in new browser window to get more information on Basic Properties of Electric Charge www.askiitians.com/iit-jee-electrostatics/basic-properties-of-electric-charge/
An electric current is the rate of flow of electric charge past a point or region. An electric current is said to exist when there is a net flow of electric charge through a region. In electric circuits this charge is often carried by electrons moving through a wire. It can also be carried by ions in an electrolyte, or by both ions and electrons such as in an ionized gas (plasma).
As charges are of two types, positive and negative, there are other certain basic properties they follow. If the size of charged bodies is so small, we consider them as point charges. Copy the link given below and paste it in new browser window to get more information on Basic Properties of Electric Charge www.askiitians.com/iit-jee-electrostatics/basic-properties-of-electric-charge/
This is a summary of the topic "Energy, work and power" in the GCE O levels subject: Physics. Students taking either the combined science (chemistry/physics) or pure Physics will find this useful. These slides are prepared according to the learning outcomes required by the examinations board.
This is first PPT in the electrostatics series. This PPT presents idea of charge , its various methods of production like through conduction, friction, induction. It also describes working of electroscope & concept of grounding of an insulator.
Presentation on Electromagnetic Induction.
Physics two presentation of CSE dept. Southeast University.
PPTX slides made by Saleh Ibne Omar.
December 2017.
Describes electrostatic principles and concepts.
**More good stuff available at:
www.wsautter.com
and
http://www.youtube.com/results?search_query=wnsautter&aq=f
Electric Charge and Electric Field LectureFroyd Wess
More: http://www.pinoybix.org
Lesson Objectives:
Static Electricity; Electric Charge and Its Conservation
Electric Charge in the Atom
Insulators and Conductors
Induced Charge; the Electroscope
Coulomb’s Law
Solving Problems Involving Coulomb’s Law and Vectors
The Electric Field
Field Lines
Electric Fields and Conductors
Gauss’s Law
Electric Forces in Molecular Biology: DNA Structure and Replication
Photocopy Machines and Computer Printers Use Electrostatics
This is a summary of the topic "Energy, work and power" in the GCE O levels subject: Physics. Students taking either the combined science (chemistry/physics) or pure Physics will find this useful. These slides are prepared according to the learning outcomes required by the examinations board.
This is first PPT in the electrostatics series. This PPT presents idea of charge , its various methods of production like through conduction, friction, induction. It also describes working of electroscope & concept of grounding of an insulator.
Presentation on Electromagnetic Induction.
Physics two presentation of CSE dept. Southeast University.
PPTX slides made by Saleh Ibne Omar.
December 2017.
Describes electrostatic principles and concepts.
**More good stuff available at:
www.wsautter.com
and
http://www.youtube.com/results?search_query=wnsautter&aq=f
Electric Charge and Electric Field LectureFroyd Wess
More: http://www.pinoybix.org
Lesson Objectives:
Static Electricity; Electric Charge and Its Conservation
Electric Charge in the Atom
Insulators and Conductors
Induced Charge; the Electroscope
Coulomb’s Law
Solving Problems Involving Coulomb’s Law and Vectors
The Electric Field
Field Lines
Electric Fields and Conductors
Gauss’s Law
Electric Forces in Molecular Biology: DNA Structure and Replication
Photocopy Machines and Computer Printers Use Electrostatics
Basic of circuit
Charge
Charge is an electrical property of the atomic particles which matter consists.
The unit of charge is the coulomb (C).
The symbol for the charge is Q (or) q.
ퟏ풄풐풖풍풐풎풃=ퟏ/(ퟏ.ퟔퟎퟐ×〖ퟏퟎ〗^(−ퟏퟗ) )=ퟔ.ퟐퟒ× 〖ퟏퟎ〗^ퟏퟖ 풆풍풆풄풕풓풐풏풔
Types of charge
Positive charge
Negative charge
A single electron has a charge of -1.602x10-19 c.
A single proton has a charge of +1.602x10-19 c.
Current
The flow of free electrons in a conductor is called electric current.
The electric current is defined as the time rate of charge.
The unit of current is the ampere (A).
The symbol for the current is I (or) i.
1ampere=1coulomb/second
Voltage
The potential difference between two points in an electric circuit called voltage.
The unit of voltage is volt.
Voltage is represented by V (or) v.
Power
The rate at which work done by electrical energy (or) energy supplied per unit time is called the power.
Power is the rate at which energy is expanded or the absorbing.
The power denoted by either P or p.
It is measured in watts (W). P = V x I
Network
Interconnection of two or more simple circuit elements is called an electric network.
Circuit
A network contains at least one closed path, it is called electrical circuit.
Active Elements
The sources of energy are called active element. They may be voltage source or current source.
Example:
Generators, Transistors, etc.
Passive Elements
These elements stores (in the form of electrostatic, electromagnetic energy) or dissipates energy (in the form of heat).
Example:
Resistance (R), Inductor (L), Capacitor (C).
Resistance
It is the property of a substance which opposes the flow of current through it.
The resistance of element is denoted by the symbol “R”.
It is measured in Ohms (Ω).
Inductor
It is the property of a substance which stores energy in the form of electromagnetic field.
The inductance of element is denoted by the symbol “L”.
It is measured in Henry (Η).
Capacitor
It is the property of a substance which stores energy in the form of electrostatic field.
The capacitance of element is denoted by the symbol “C”
It is measured in Farads (Ϝ).
Have you ever experienced a crackling sound or witnessed a spark while removing synthetic clothes or a sweater, especially in dry weather? This phenomenon occurs due to the discharge of electric charges accumulated through the rubbing of insulating surfaces. Another example of electric discharge is lightning observed during thunderstorms. These occurrences result from static electricity generation. NCERT Class 12 Physics Notes Chapter 1 on Electric Charges and Fields delves into these phenomena extensively. Electrostatics is the branch of physics that investigates forces, fields, and potentials arising from static charges.
For more information, visit- www.vavaclasses.com
Richard's entangled aventures in wonderlandRichard Gill
Since the loophole-free Bell experiments of 2020 and the Nobel prizes in physics of 2022, critics of Bell's work have retreated to the fortress of super-determinism. Now, super-determinism is a derogatory word - it just means "determinism". Palmer, Hance and Hossenfelder argue that quantum mechanics and determinism are not incompatible, using a sophisticated mathematical construction based on a subtle thinning of allowed states and measurements in quantum mechanics, such that what is left appears to make Bell's argument fail, without altering the empirical predictions of quantum mechanics. I think however that it is a smoke screen, and the slogan "lost in math" comes to my mind. I will discuss some other recent disproofs of Bell's theorem using the language of causality based on causal graphs. Causal thinking is also central to law and justice. I will mention surprising connections to my work on serial killer nurse cases, in particular the Dutch case of Lucia de Berk and the current UK case of Lucy Letby.
Slide 1: Title Slide
Extrachromosomal Inheritance
Slide 2: Introduction to Extrachromosomal Inheritance
Definition: Extrachromosomal inheritance refers to the transmission of genetic material that is not found within the nucleus.
Key Components: Involves genes located in mitochondria, chloroplasts, and plasmids.
Slide 3: Mitochondrial Inheritance
Mitochondria: Organelles responsible for energy production.
Mitochondrial DNA (mtDNA): Circular DNA molecule found in mitochondria.
Inheritance Pattern: Maternally inherited, meaning it is passed from mothers to all their offspring.
Diseases: Examples include Leber’s hereditary optic neuropathy (LHON) and mitochondrial myopathy.
Slide 4: Chloroplast Inheritance
Chloroplasts: Organelles responsible for photosynthesis in plants.
Chloroplast DNA (cpDNA): Circular DNA molecule found in chloroplasts.
Inheritance Pattern: Often maternally inherited in most plants, but can vary in some species.
Examples: Variegation in plants, where leaf color patterns are determined by chloroplast DNA.
Slide 5: Plasmid Inheritance
Plasmids: Small, circular DNA molecules found in bacteria and some eukaryotes.
Features: Can carry antibiotic resistance genes and can be transferred between cells through processes like conjugation.
Significance: Important in biotechnology for gene cloning and genetic engineering.
Slide 6: Mechanisms of Extrachromosomal Inheritance
Non-Mendelian Patterns: Do not follow Mendel’s laws of inheritance.
Cytoplasmic Segregation: During cell division, organelles like mitochondria and chloroplasts are randomly distributed to daughter cells.
Heteroplasmy: Presence of more than one type of organellar genome within a cell, leading to variation in expression.
Slide 7: Examples of Extrachromosomal Inheritance
Four O’clock Plant (Mirabilis jalapa): Shows variegated leaves due to different cpDNA in leaf cells.
Petite Mutants in Yeast: Result from mutations in mitochondrial DNA affecting respiration.
Slide 8: Importance of Extrachromosomal Inheritance
Evolution: Provides insight into the evolution of eukaryotic cells.
Medicine: Understanding mitochondrial inheritance helps in diagnosing and treating mitochondrial diseases.
Agriculture: Chloroplast inheritance can be used in plant breeding and genetic modification.
Slide 9: Recent Research and Advances
Gene Editing: Techniques like CRISPR-Cas9 are being used to edit mitochondrial and chloroplast DNA.
Therapies: Development of mitochondrial replacement therapy (MRT) for preventing mitochondrial diseases.
Slide 10: Conclusion
Summary: Extrachromosomal inheritance involves the transmission of genetic material outside the nucleus and plays a crucial role in genetics, medicine, and biotechnology.
Future Directions: Continued research and technological advancements hold promise for new treatments and applications.
Slide 11: Questions and Discussion
Invite Audience: Open the floor for any questions or further discussion on the topic.
THE IMPORTANCE OF MARTIAN ATMOSPHERE SAMPLE RETURN.Sérgio Sacani
The return of a sample of near-surface atmosphere from Mars would facilitate answers to several first-order science questions surrounding the formation and evolution of the planet. One of the important aspects of terrestrial planet formation in general is the role that primary atmospheres played in influencing the chemistry and structure of the planets and their antecedents. Studies of the martian atmosphere can be used to investigate the role of a primary atmosphere in its history. Atmosphere samples would also inform our understanding of the near-surface chemistry of the planet, and ultimately the prospects for life. High-precision isotopic analyses of constituent gases are needed to address these questions, requiring that the analyses are made on returned samples rather than in situ.
Introduction:
RNA interference (RNAi) or Post-Transcriptional Gene Silencing (PTGS) is an important biological process for modulating eukaryotic gene expression.
It is highly conserved process of posttranscriptional gene silencing by which double stranded RNA (dsRNA) causes sequence-specific degradation of mRNA sequences.
dsRNA-induced gene silencing (RNAi) is reported in a wide range of eukaryotes ranging from worms, insects, mammals and plants.
This process mediates resistance to both endogenous parasitic and exogenous pathogenic nucleic acids, and regulates the expression of protein-coding genes.
What are small ncRNAs?
micro RNA (miRNA)
short interfering RNA (siRNA)
Properties of small non-coding RNA:
Involved in silencing mRNA transcripts.
Called “small” because they are usually only about 21-24 nucleotides long.
Synthesized by first cutting up longer precursor sequences (like the 61nt one that Lee discovered).
Silence an mRNA by base pairing with some sequence on the mRNA.
Discovery of siRNA?
The first small RNA:
In 1993 Rosalind Lee (Victor Ambros lab) was studying a non- coding gene in C. elegans, lin-4, that was involved in silencing of another gene, lin-14, at the appropriate time in the
development of the worm C. elegans.
Two small transcripts of lin-4 (22nt and 61nt) were found to be complementary to a sequence in the 3' UTR of lin-14.
Because lin-4 encoded no protein, she deduced that it must be these transcripts that are causing the silencing by RNA-RNA interactions.
Types of RNAi ( non coding RNA)
MiRNA
Length (23-25 nt)
Trans acting
Binds with target MRNA in mismatch
Translation inhibition
Si RNA
Length 21 nt.
Cis acting
Bind with target Mrna in perfect complementary sequence
Piwi-RNA
Length ; 25 to 36 nt.
Expressed in Germ Cells
Regulates trnasposomes activity
MECHANISM OF RNAI:
First the double-stranded RNA teams up with a protein complex named Dicer, which cuts the long RNA into short pieces.
Then another protein complex called RISC (RNA-induced silencing complex) discards one of the two RNA strands.
The RISC-docked, single-stranded RNA then pairs with the homologous mRNA and destroys it.
THE RISC COMPLEX:
RISC is large(>500kD) RNA multi- protein Binding complex which triggers MRNA degradation in response to MRNA
Unwinding of double stranded Si RNA by ATP independent Helicase
Active component of RISC is Ago proteins( ENDONUCLEASE) which cleave target MRNA.
DICER: endonuclease (RNase Family III)
Argonaute: Central Component of the RNA-Induced Silencing Complex (RISC)
One strand of the dsRNA produced by Dicer is retained in the RISC complex in association with Argonaute
ARGONAUTE PROTEIN :
1.PAZ(PIWI/Argonaute/ Zwille)- Recognition of target MRNA
2.PIWI (p-element induced wimpy Testis)- breaks Phosphodiester bond of mRNA.)RNAse H activity.
MiRNA:
The Double-stranded RNAs are naturally produced in eukaryotic cells during development, and they have a key role in regulating gene expression .
This pdf is about the Schizophrenia.
For more details visit on YouTube; @SELF-EXPLANATORY;
https://www.youtube.com/channel/UCAiarMZDNhe1A3Rnpr_WkzA/videos
Thanks...!
Seminar of U.V. Spectroscopy by SAMIR PANDASAMIR PANDA
Spectroscopy is a branch of science dealing the study of interaction of electromagnetic radiation with matter.
Ultraviolet-visible spectroscopy refers to absorption spectroscopy or reflect spectroscopy in the UV-VIS spectral region.
Ultraviolet-visible spectroscopy is an analytical method that can measure the amount of light received by the analyte.
A brief information about the SCOP protein database used in bioinformatics.
The Structural Classification of Proteins (SCOP) database is a comprehensive and authoritative resource for the structural and evolutionary relationships of proteins. It provides a detailed and curated classification of protein structures, grouping them into families, superfamilies, and folds based on their structural and sequence similarities.
1. 1 | P a g e
Charge
In physics, a charge may refer to one of many different quantities, such as the electric
charge in electromagnetism or the color charge in quantum chromodynamics. Charges are associated
with conserved quantum numbers.
Electric charge
Electric charge is the physical property of matter that causes it to experience a force when close to other
electrically charged matter. There are two types of electric charges, called positive and negative.
Positively charged substances are repelled from other positively charged substances, but attracted to
negatively charged substances; negatively charged substances are repelled from negative and attracted
to positive. An object will be negatively charged if it has an excess of electrons, and will otherwise be
positively charged or uncharged. The SI unit of electric charge is the coulomb (C), although in electrical
engineering it is also common to use the ampere-hour (Ah), and in chemistry it is common to use the
elementary charge (e) as a unit. The symbol Q is often used to denote a charge.
The electric charge is a fundamental conserved property of some subatomic particles, which determines
their electromagnetic interaction. Electrically charged matter is influenced by, and produces,
electromagnetic fields. The interaction between a moving charge and an electromagnetic field is the
source of the electromagnetic force, which is one of the four fundamental forces.
Twentieth-century experiments demonstrated that electric charge is quantized; that is, it comes in integer
multiples of individual small units called the elementary charge, e, approximately equal to 1.602×10−19
coulombs (except for particles called quarks, which have charges that are integer multiples of e/3). The
proton has a charge of e, and the electron has a charge of −e.
Overview
Charge is the fundamental property of forms of matter that exhibit electrostatic attraction or repulsion in
the presence of other matter. Electric charge is a characteristic property of many subatomic particles. The
charges of free-standing particles are integer multiples of the elementary charge e; we say that electric
charge is quantized. Michael Faraday, in his electrolysis experiments, was the first to note the discrete
nature of electric charge. Robert Millikan's oil-drop experiment demonstrated this fact directly, and
measured the elementary charge.
During the formation of macroscopic objects, usually the const ituent atoms and ions will combine in such
a manner that they form structures composed of neutral ionic compounds electrically bound to neutral
atoms. Thus macroscopic objects tend toward being neutral overall, but macroscopic objects are rarely
perfectly net neutral.
There are times when macroscopic objects contain ions distributed throughout the material, rigidly bound
in place, giving an overall net positive or negative charge to the object. Also, macroscopic objects made
of conductive elements, can more or less easily (depending on the element) take on or give off electrons,
and then maintain a net negative or positive charge indefinitely. When the net electric charge of an object
2. is non-zero and motionless, the phenomenon is known as static electricity. Charge can easily be
produced by rubbing two dissimilar materials together, such as rubbing amber with fur or glass with silk.
In this way non-conductive materials can be charged to a significant degree, either positively or
negatively.
Finding The Charge on e- using MODE i.e.
________Millikan Oil Drop Experiment
•The Oil-Drop Experiment involved ionizing droplets of oil as they fell through the air, and balancing the
force of gravity with the force of an electric applied by electrodes above and below the droplet.
•Millikan could not directly count the number of electrons on each oil droplet, but found that the common
denominator between all measured charges was equal to 1.5924 ×10−19 C, and thus concluded that this
value was the charge of an electron.
•The measured value of an electron's charge, 1.5924 ×10−19 C, differs from the accepted value of
1.602176487 ×10−19 C by less than one percent.
Voltage:
The amount of electrostatic potential between two points in space.
Electric field:
A region of space around a charged particle, or between two voltages; it exerts a force on charged
objects in its vicinity.
Terminal velocity:
The speed at which an object in free-fall and not in a vacuum ceases to accelerate downwards because
the force of gravity is equal and opposite of the drag force acting against it.
The Oil-Drop Experiment:
The Oil-Drop Experiment, otherwise known as the Millikan Oil-Drop Experiment, is one of the most
influential studies in the history of physical science.
Performed by Robert Millikan and Harvey Fletcher in 1911, the experiment was designed to determine
the charge of a single electron, otherwise known as the elementary electric charge. Millikan designed his
experiment to measure the force on oil droplets between two electrodes.
He used an atomizer to spray a mist of tiny oil droplets into a chamber, which included a hole. Some
droplets would fall through this hole and into a chamber, where he measured their terminal velocity and
calculated their mass. Millikan then exposed the droplets to X-rays, which ionized molecules in the air and
caused electrons to attach to the oil droplets, thus making them charged. The top and bottom of the
chamber were attached to a battery, and the potential difference between the top and bottom produc ed
an electric field that acted on the charged oil drops.
2 | P a g e
3. Adjusting the voltage perfectly, Millikan was able to balance the force of gravity (which was exerted
downward) with the force of the electric field on the charged particles (which was exerted upward),
causing the oil droplets to be suspended in mid-air. A visual representation of the experiment can be seen
in the figure:
Millikan then calculated the charge on particles suspended in mid-air. His assumptions were that the force
of gravity, which is the product of mass (m) and gravitational acceleration (g), was equal to the force of
the electric field (the product of the charge (q) and the electric field (E)):
Although the charge of each droplet was unknown, Millikan adjusted the strength of the X-rays ionizing
the air and measured many values of (q) from many different oil droplets. In each instance, the charge
measured was a multiple of 1.5924 ×10−19 C. Thus, it was concluded that the elementary electric charge
was 1.5924 ×10−19 C.
The results were very accurate. The calculated value from the Oil-Drop Experiment differs by less than
one percent of the current accepted value of 1.602176487 ×10−19 C.
The Oil-Drop Experiment was tremendously influential at the time, not only for determining the charge of
an electron, but for helping prove the existence of particles smaller than atoms. At the time, it was not
fully accepted that protons, neutrons, and electrons existed.
Conductors and Insulators
Some substances readily allow passage of electricity through them, others do not. Those which allow
electricity to pass through them easily are called conductors. They have electric charges (electrons) that
are comparatively free to move inside the material. Metals, human and animal bodies and earth are
conductors. Most of the non-metals like glass, porcelain, plastic, nylon, wood offer high resistance to the
passage of electricity through them. They are called insulators. Most substances fall into one of the two
classes stated above.
When some charge is transferred to a conductor, it readily gets distributed over the entire surface of the
conductor. In contrast, if some charge is put on an insulator, it stays at the same place. You will learn why
this happens in the next chapter. This property of the materials tells you why a nylon or plastic comb gets
electrified on combing dry hair or on rubbing, but a metal article like spoon does not. The charges on
metal leak through our body to the ground as both are conductors of electricity. When we bring a charged
3 | P a g e
4. body in contact with the earth, all the excess charge on the body disappears by causing a momentary
current to pass to the ground through the connecting conductor (such as our body). This process of
sharing the charges with the earth is called grounding or earthing.
Earthing provides a safety measure for electrical circuits and appliances. A thick metal plate is buried
deep into the earth and thick wires are drawn from this plate; these are used in buildings for the purpose
of earthing near the mains supply. The electric wiring in our houses has three wires: live, neutral and
earth. The first two carry electric current from the power station and the third is earthed by connecting it to
the buried metal plate. Metallic bodies of the electric appliances such as electric iron, refrigerator, TV are
connected to the earth wire. When any fault occurs or live wire touches the metallic body, the charge
flows to the earth without damaging the appliance and without causing any injury to the humans; this
would have otherwise been unavoidable since the human body is a conductor of electricity.
Static electricity and electric current
Static electricity and electric current are two separate phenomena, both involving electric charge, and
may occur simultaneously in the same object. Static electricity is a reference to the electric charge of an
object and the related electrostatic discharge when two objects are brought together that is not at
equilibrium. An electrostatic discharge creates a change in the charge of each of the two objects. In
contrast, electric current is the flow of electric charge through an object, which produces no net loss or
gain of electric charge.
Electrification by friction
Let a piece of glass and a piece of resin, neither of which exhibiting any electrical properties, be rubbed
together and left with the rubbed surfaces in contact. They will still exhibit no electrical properties. Let
them be separated. They will now attract each other.
If a second piece of glass be rubbed with a second piece of resin, and if the piece be then separated and
suspended in the neighborhood of the former pieces of glass and resin, it may be observed:
1. That the two pieces of glass repel each other.
2. That each piece of glass attracts each piece of resin.
3. That the two pieces of resin repel each other.
These phenomena of attraction and repulsion are called electrical phenomena, and the bodies that exhibit
them are said to be 'electrified', or to be 'charged with electricity'.
Bodies may be electrified in many other ways, as well as by friction.
The electrical properties of the two pieces of glass are similar to each other but opposite to those of the
two pieces of resin: The glass attracts what the resin repels and repels what the resin attracts.
4 | P a g e
5. No force, either of attraction or of repulsion, can be observed between an electrified body and a body
nonelectrified.
Actually, all bodies are electrified, but may appear not to be so by the relative similar charge of
neighboring objects in the environment. An object further electrified + or - creates an equivalent or
opposite charge by default in neighboring objects, until those charges can equalize. The effects of
attraction can be observed in high-voltage experiments, while lower voltage effects are merely weaker
and therefore less obvious. The attraction and repulsion forces are codified by Coulomb's Law (attraction
falls off at the square of the distance, which has a corollary for acceleration in a gravitational field,
suggesting that gravitation may be merely electrostatic phenomenon between relatively weak charges in
terms of scale).
Electrification by induction
Electrostatic induction is a redistribution of electrical charge in an object, caused by the influence of
nearby charges. Induction was discovered by British scientist John Canton in 1753 and Swedish
professor Johan Carl Wilcke in 1762. Electrostatic generators, such as the Wimshurst machine, the Van
de Graaff generator and the electrophorus, use this principle. Induction is also responsible for the
attraction of light nonconductive objects, such as balloons, paper or Styrofoam scraps, to static electric
charges.
A normal uncharged piece of matter has equal numbers of positive and negative electric charges in each
part of it, located close together, so no part of it has a net electric charge. The positive charges are the
atoms' nuclei which are bound into the structure of matter and are not free to move. The negative charges
are the atoms' electrons. In electrically conductive objects such as metals, some of the electrons are able
to move freely about in the object.
When a charged object is brought near an uncharged object, electrically conducting object, such as a
piece of metal, the force of the nearby charge causes a separation of these charges. For example, if a
positive charge is brought near the object, the electrons in the metal will be attracted toward it and move
to the side of the object facing it. When the electrons move out of an area, they leave an unbalanced
positive charge due to the nuclei. This results in a region of negative charge on the object nearest to the
5 | P a g e
6. external charge, and a region of positive charge on the part away from it. These are called induced
charges. If the external charge is negative, the polarity of the charged regions will be reversed.
Since this process is just a redistribution of the charges that were already in the object, it doesn't change
the total charge on the object; it still has no net charge. This induction effect is reversible; if the nearby
charge is removed, the attraction between the positive and negative internal charges causes them to
intermingle again.
Induction can be demonstrated using a Gold-leaf Electroscope, which is an instrument for detecting
electric charge. The electroscope is first discharged, and a charged object is then brought close to the
instrument's top terminal. Induction causes a redistribution of the charges inside the electroscope's metal
rod, so that the top terminal gains a net charge of opposite polarity to that of the object, while the gold
leaves gain a charge of the same polarity. Since both leaves have the same charge, they repel each
other and spread apart.
The electroscope has not acquired a net charge: the charge within it has merely been redistributed, so if
the charge were to be moved away from the electroscope the leaves will come together again.
But if an electrical contact is now briefly made between the electroscope terminal and ground, for
example by touching the terminal with a finger, this causes charge to flow from ground to the terminal,
attracted by the charge on the object close to the terminal. The electroscope now contains a net charge
opposite in polarity to that of the charged object. When the electrical contact to earth is broken, e.g. by
lifting the finger, the extra charge that has just flowed into the electroscope cannot escape, and the
instrument retains a net charge. So the gold leaves remain separated even after the nearby charged
object is moved away.
The sign of the charge left on the electroscope after grounding is always opposite in sign to the external
inducing charge. On the other hand, an opposite permanent charge on an object can be achieved if it is
grounded from the opposite edge to that which is bearing the external induction charge.
Basic Properties of Charge
6 | P a g e
Gold-leaf electroscope, show ing induction,
before the terminal is grounded.
7. (i) Additivity of charges
•Charges adds up like real numbers i. e., they are Scalars more clearly if any system has n number of
charges q1, q2, q3, qn then total charge of the system is
q = q1 + q2 + q3 + ................ qn
•Proper sign have to be used while adding the charges for example if
q1 = +1C
q2 = -2C
q3 = +4C
Then total charge of the system is
q = q1 + q2 + q3
q = (+1) + (-2) + (+4) C
q = (+3) C
(ii) Charge is conserved
•Charge of an isolated system is conserved.
•Charge cannot be created or destroyed but charged particles can be created or destroyed.
(iii) Quantization of charge
All free charges are integral multiples of a unit of charge e, where e = -1.602 × 10 -19 C i. e., charge on an
electron or proton.
Thus charge q on a body is always denoted by
q = ne
Where n = any integer positive or negative
(iv) Invariance
Like mass, electric charge in a closed system is conserved. As long as a system is impermeable, the
amount of charge inside it will neither increase nor decrease; it can only be transferred. However, electric
charge differs from other properties—like mass—in that it is a relativistic invariant. That is, charge
is independent of speed. The mass of a particle will rise exponentially as its speed approaches that of
light, its charge, however, will remain constant.
7 | P a g e
8. The independence of electric charge from speed was proven through an experiment in which one fast-moving
helium nucleus (two protons and two neutrons bound together) was proven to have the same
charge as two separate, slow-moving deuterium nuclei (one proton and one neutron bound together in
each nucleus).
From this we get that-
Coulomb’s Law
m
r
= m
0
/ √ (1 - v2/c2)
Coulomb's law is the law of forces between electric charges.
Statement- “It states that two stationary point charges q1 and q2 repel or attract each other with a force F
which is directly proportional to the product of charges and inversely proportional to the square of
distance between them."
If the two charges have the same sign, the electrostatic force between them is repulsive; if they have
different sign, the force between them is attractive. The scalar and vector forms of the mathematical
equation are-
8 | P a g e
&
The Electric Field
Suppose we have a point charge q0 located at r and a set of external charges conspire so as to exert a
force F on this charge. We can define the electric field at the point r by:
_____________________________________________________________ (1.1)
The (vector) value of the E field depends only on the values and locations of the external charges,
because from Coulomb’s law the force on any “test charge” q0 is proportional to the value of the charge.
9. However to make this definition really kosher we have to stipulate that the tes t charge q0 is “small”;
otherwise its presence will significantly influence the locations of the external charges.
Turning Eq. 1.1 around, we can say that if the electric field at some point r has the value E then a small
charge placed at r will experience a force
9 | P a g e
________________________________________________________________ (1.2)
The electric field is a vector. From Eq. 1.1 we can see that its SI units must be N/C. It follows from
Coulomb’s law that the electric field at point r due to a charge q located at the origin is given by
__________________________________________________________ (1.3)
Where ṝ is the unit vector which points in the same direction as r.
Electric Field Lines Due to Charged Particle
From Coulomb’s law we get that-
Since electric field varies as inverse of square of the distance that points from the charge the
vector gets shorter as you go away from the origin and they always points radially outwards.
Connecting up these vectors to form a line is a nice way to represent this field.
The magnitude of the field is indicated by the density of the field lines.
Magnitude is strong near the center where the field lines are close together, and weak farther out,
where they are relatively apart.
So, electric field line is an imaginary line drawn in such a way that its direction at any point is
same as the direction of field at that point.
An electric field line is, in general a curve drawn in such a way that the tangent to it at each point
is the direction of net field at that point.
Field lines of a single position charge points radially outwards while that of a negative charge is
radially inwards as shown below in the figure.
10. •Field lines around the system of two positive charges give a different picture and describe the mutual
repulsion between them.
10 | P a g e
11. Field lines around a system of a positive and negative charge clearly shows the mutual attraction
between them as shown below in the figure.
Some important general properties of field lines are:
•Field lines start from positive charge and end on a negative charge.
•Field lines never cross each other if they do so then at the point of intersection there will be two direction
of electric field.
•Electric field lines do not pass through a conductor, this shows that electric field inside a conductor is
always zero.
•Electric field lines are continuous curves in a charge free region.
Conservation of electric charge:
Electric charges can neither be created nor destroyed. According to the law of conservation of
electric charge, the total charge in an isolated system always remains constant. But the charges
can be transferred from one part of the system to another, such that the total charge always
remains conserved. For example, Uranium (92U238) can decay by emitting an alpha particle
(2He4 nucleus) and transforming to Thorium (90Th234).
11 | P a g e
92U238 90Th 234 + 2He4
Total charge before decay = +92e, total charge after decay = 90e + 2e. Hence, the total charge is
conserved i.e. it remains constant.
12. Electric Dipole
An electric dipole is a pair of charges of opposite sign (±q) separated by a distance d which is usually
meant to be small compared to the distance from the charges at which we want to find the electric field.
The product qd turns out to be important; the vector which points from the −q charge to the +q charge and
has magnitude qd is known as the electric dipole moment for the pair, and is denoted p.
Suppose we form an electric dipole by placing a charge +q at (0, 0, d/2) and a charge −q at (0, 0, −d/2).
One can show that when z is much larger than d, the electric field for points on the z axis is
12 | P a g e
__________________________________ (1.4)
Van de Graaff generator
A Van de Graaff generator is an electrostatic generator which uses a moving belt to accumulate very high
amounts of electrical charge on a hollow metal globe on the top of the stand. It was invented by American
physicist Robert J. Van de Graaff in 1929. The potential difference achieved in modern Van de Graaff
generators can reach 5 megavolts. A tabletop version can produce on the order of 100,000 volts and can
store enough energy to produce a visible spark.
A Van de Graaff generator operates by transferring electric charge from a moving belt to a terminal. First
invented in 1929, the Van de Graaff generator became a source of high voltage for accelerating
subatomic particles to high speeds, making it a useful tool for fundamental physics research.
A simple Van de Graaff-generator consists of a belt of silk, or a similar flexible dielectric material, running
over two metal pulleys, one of which is surrounded by a hollow metal sphere. Two electrodes, (2) and (7),
in the form of comb-shaped rows of sharp metal points, are positioned respectively near to the bottom of
13. the lower pulley and inside the sphere, over the upper pulley. Comb (2) is connected to the sphere, and
comb (7) to the ground. A high DC potential (with respect to earth) is applied to roller (3); a positive
potential in this example.
As the belt passes in front of the lower comb, it receives negative charge that escapes from its points due
to the influence of the electric field around the lower pulley, which ionizes the air at the points. As the belt
touches the upper roller (6), it transfers some electrons, leaving the roller with a negative charge (if it is
insulated from the terminal), which added to the negative charge in the belt generates enough electric
field to ionize the air at the points of the upper comb. Electrons then leak from the belt to the upper comb
and to the terminal, leaving the belt positively charged as it returns down and the terminal negatively
charged. The sphere shields the upper roller and comb from the electric field generated by charges that
accumulate at the outer surface of it, causing the discharge and change of polarity of the belt at the upper
roller to occur practically as if the terminal were grounded. As the belt continues to move, a
constant charging current travels via the belt, and the sphere continues to accumulate negative charge
until the rate that charge is being lost (through leakage and corona discharges) equals the charging
current. The larger the sphere and the farther it is from ground, the higher will be its final potential.
13 | P a g e
Schematic view of a classical Van de Graaff-generator.
1) hollow metal sphere
2) upper electrode
3) upper roller (for example an acrylic glass)
4) side of the belt with positive charges
5) opposite side of the belt with negative charges
6) lower roller (metal)
7) lower electrode (ground)
8) spherical device with negative charges, used to
discharge the main sphere
9) spark produced by the difference of potentials
14. Electric flux
In electromagnetism, electric flux is the rate of flow of the electric field through a given area. Electric flux
is proportional to the number of electric lines going through a virtual surface. In other words the number of
electric lines of force passing through the given surface area which is held perpendicular to the direction
of electric lines of force is called electric flux. If the electric field is uniform, the electric flux passing
through a surface of vector area S is
Where E is the magnitude of the electric field (having units of V/m), S is the area of the surface, and θ is
the angle between the electric field lines and the normal (perpendicular) to S. For a non-uniform electric
field, the electric flux dΦE through small surface area dS is given by
(The electric field, E, multiplied by the component of area perpendicular to the field). The electric flux over
a surface S is therefore given by the surface integral:
Where E is the electric field and dS is a differential area on the closed surface S with an outward
facing surface normal defining its direction.
For a closed Gaussian surface, electric flux is given by:
Where-
E is the electric field,
S is any closed surface,
Q is the total electric charge inside the surface S,
ε0 is the electric constant (a universal constant, also called the "permittivity of free space").
This relation is known as Gauss' law for electric field in its integral form and it is one of the four Maxwell's
equations.
14 | P a g e
15. It is important to note that while the electric flux is not affected by charges that are not within the closed
surface, the net electric field, E, in the Gauss' Law equation, can be affected by charges that lie outside
the closed surface. While Gauss' Law holds for all situations, it is only useful for "by hand" calculations
when high degrees of symmetry exist in the electric field. Examples include spherical and cylindrical
symmetry.
Electrical flux has SI units of volt meters (V m), or, equivalently, newton meters squared per coulomb (N
m2 C−1). Thus, the SI base units of electric flux are kg·m3·s−3·A−1.
Its dimensional formula is [L3MT–1I–1].
Gauss's law
In physics, Gauss's law, also known as Gauss's flux theorem, is a law relating the distribution of electric
charge to the resulting electric field.
The law was formulated by Carl Friedrich Gauss in 1835, but was not published until 1867. It is one of the
four Maxwell's equations which form the basis of classical electrodynamics.
-Qualitative description of the law
In words, Gauss's law states that:
The net outward normal electric flux through any closed surface is proportional to the total electric
charge enclosed within that closed surface.
Gauss's law has a close mathematical similarity with a number of laws in other areas of physics, such
as Gauss's law for magnetism and Gauss's law for gravity. In fact, any "inverse-square law" can be
formulated in a way similar to Gauss's law: For example, Gauss's law itself is essentially equivalent to the
inverse-square Coulomb's law.
-Equation involving E field
Gauss's law can be stated using either the electric field E or the electric displacement field D. This section
shows some of the forms with E; the form with D is below, as are other forms with E.
Integral form
Gauss's law may be expressed as:
Where ΦE is the electric flux through a closed surface S enclosing any volume V, Q is the
total charge enclosed within S, and ε0 is the electric constant. The electric flux ΦE is defined as a surface
integral of the electric field:
15 | P a g e
16. Where E is the electric field, dA is a vector representing an infinitesimal element of area and • represents
the dot product of two vectors.
Since the flux is defined as an integral of the electric field, this expression of Gauss's law is called
the integral form.
In summary, Gauss’s Law is usually used in either of two ways:
1) Given the field and the surface then enclosed charge can be found.
2) Given the enclosed charge and sufficient symmetry to choose a convenient surface, then the field can
be found.
16 | P a g e
******************
**************
**********
******
***
*