This document provides an overview of LAN network design and various high-speed networking technologies. It discusses the evolution of networking needs that led to faster LANs, describes Ethernet and some of its variants like Fast Ethernet and Gigabit Ethernet. It also covers wireless LAN technologies and fiber optic networks like Fibre Channel. Key concepts explained include CSMA/CD, full duplex operation, and different physical layer specifications for networks operating at speeds of 100Mbps, 1Gbps, and 10Gbps.
This was made along with a simple research paper in my Network + course. I don't have any negative intention in uploading of this. I only hope it could help in any ways
This slide deck was used for a 2-day short course at IIT Gandhinagar in Spring 2015. Being a 2-day course, it focuses more on a qualitative description of how we access the Internet.
LAN
A Local Area Network (LAN) was originally defined as a network of computers located within the same area
Local Area Networks are defined as a single broadcast domain. This means that if a user broadcasts information on his/her LAN, the broadcast will be received by every other user on the LAN.
Broadcasts are prevented from leaving a LAN by using a router. The disadvantage of this method is routers usually take more time to process incoming data compared to a bridge or a switch
Analyze the Customer Requirements
Characterize the Existing Network and Sites
Design the Network Topology and Solutions
Design a Network Topology
Design a Model for Network Layer Addressing and Naming
Select the Switching and Routing Protocols
Network Security Design
Network Management Design
Optimize the Network Design
Select Technologies and Devices
Test the Network Design
Document the Network Design
This was made along with a simple research paper in my Network + course. I don't have any negative intention in uploading of this. I only hope it could help in any ways
This slide deck was used for a 2-day short course at IIT Gandhinagar in Spring 2015. Being a 2-day course, it focuses more on a qualitative description of how we access the Internet.
LAN
A Local Area Network (LAN) was originally defined as a network of computers located within the same area
Local Area Networks are defined as a single broadcast domain. This means that if a user broadcasts information on his/her LAN, the broadcast will be received by every other user on the LAN.
Broadcasts are prevented from leaving a LAN by using a router. The disadvantage of this method is routers usually take more time to process incoming data compared to a bridge or a switch
Analyze the Customer Requirements
Characterize the Existing Network and Sites
Design the Network Topology and Solutions
Design a Network Topology
Design a Model for Network Layer Addressing and Naming
Select the Switching and Routing Protocols
Network Security Design
Network Management Design
Optimize the Network Design
Select Technologies and Devices
Test the Network Design
Document the Network Design
It provide the basic features of bottom two layers i.e. Physical layer and Data Link Layer with the features, functionality and services provided by them. It also includes the concepts related to the various protocols.
Safalta Digital marketing institute in Noida, provide complete applications that encompass a huge range of virtual advertising and marketing additives, which includes search engine optimization, virtual communication advertising, pay-per-click on marketing, content material advertising, internet analytics, and greater. These university courses are designed for students who possess a comprehensive understanding of virtual marketing strategies and attributes.Safalta Digital Marketing Institute in Noida is a first choice for young individuals or students who are looking to start their careers in the field of digital advertising. The institute gives specialized courses designed and certification.
for beginners, providing thorough training in areas such as SEO, digital communication marketing, and PPC training in Noida. After finishing the program, students receive the certifications recognised by top different universitie, setting a strong foundation for a successful career in digital marketing.
This presentation was provided by Steph Pollock of The American Psychological Association’s Journals Program, and Damita Snow, of The American Society of Civil Engineers (ASCE), for the initial session of NISO's 2024 Training Series "DEIA in the Scholarly Landscape." Session One: 'Setting Expectations: a DEIA Primer,' was held June 6, 2024.
How to Build a Module in Odoo 17 Using the Scaffold MethodCeline George
Odoo provides an option for creating a module by using a single line command. By using this command the user can make a whole structure of a module. It is very easy for a beginner to make a module. There is no need to make each file manually. This slide will show how to create a module using the scaffold method.
Executive Directors Chat Leveraging AI for Diversity, Equity, and InclusionTechSoup
Let’s explore the intersection of technology and equity in the final session of our DEI series. Discover how AI tools, like ChatGPT, can be used to support and enhance your nonprofit's DEI initiatives. Participants will gain insights into practical AI applications and get tips for leveraging technology to advance their DEI goals.
Introduction to AI for Nonprofits with Tapp NetworkTechSoup
Dive into the world of AI! Experts Jon Hill and Tareq Monaur will guide you through AI's role in enhancing nonprofit websites and basic marketing strategies, making it easy to understand and apply.
Thinking of getting a dog? Be aware that breeds like Pit Bulls, Rottweilers, and German Shepherds can be loyal and dangerous. Proper training and socialization are crucial to preventing aggressive behaviors. Ensure safety by understanding their needs and always supervising interactions. Stay safe, and enjoy your furry friends!
A Strategic Approach: GenAI in EducationPeter Windle
Artificial Intelligence (AI) technologies such as Generative AI, Image Generators and Large Language Models have had a dramatic impact on teaching, learning and assessment over the past 18 months. The most immediate threat AI posed was to Academic Integrity with Higher Education Institutes (HEIs) focusing their efforts on combating the use of GenAI in assessment. Guidelines were developed for staff and students, policies put in place too. Innovative educators have forged paths in the use of Generative AI for teaching, learning and assessments leading to pockets of transformation springing up across HEIs, often with little or no top-down guidance, support or direction.
This Gasta posits a strategic approach to integrating AI into HEIs to prepare staff, students and the curriculum for an evolving world and workplace. We will highlight the advantages of working with these technologies beyond the realm of teaching, learning and assessment by considering prompt engineering skills, industry impact, curriculum changes, and the need for staff upskilling. In contrast, not engaging strategically with Generative AI poses risks, including falling behind peers, missed opportunities and failing to ensure our graduates remain employable. The rapid evolution of AI technologies necessitates a proactive and strategic approach if we are to remain relevant.
This slide is special for master students (MIBS & MIFB) in UUM. Also useful for readers who are interested in the topic of contemporary Islamic banking.
MATATAG CURRICULUM: ASSESSING THE READINESS OF ELEM. PUBLIC SCHOOL TEACHERS I...NelTorrente
In this research, it concludes that while the readiness of teachers in Caloocan City to implement the MATATAG Curriculum is generally positive, targeted efforts in professional development, resource distribution, support networks, and comprehensive preparation can address the existing gaps and ensure successful curriculum implementation.
Exploiting Artificial Intelligence for Empowering Researchers and Faculty, In...Dr. Vinod Kumar Kanvaria
Exploiting Artificial Intelligence for Empowering Researchers and Faculty,
International FDP on Fundamentals of Research in Social Sciences
at Integral University, Lucknow, 06.06.2024
By Dr. Vinod Kumar Kanvaria
2. Introduction
range of technologies
◦ Fast and Gigabit Ethernet
◦ Fibre Channel
◦ High Speed Wireless LANs
3. Why High Speed LANs?
speed and power of PCs has risen
◦ graphics-intensive applications and GUIs
see LANs as essential to organizations
◦ for client/server computing
now have requirements for
◦ centralized server farms
◦ power workgroups
◦ high-speed local backbone
4. Ethernet (CSMA/CD)
most widely used LAN standard
developed by
◦ Xerox - original Ethernet
◦ IEEE 802.3
Carrier Sense Multiple Access with
Collision Detection (CSMA/CD)
◦ random / contention access to media
5. ALOHA
developed for packet radio nets
when station has frame, it sends
then listens for a bit over max round trip time
◦ if receive ACK then fine
◦ if not, retransmit
◦ if no ACK after repeated transmissions, give up
uses a frame check sequence (as in HDLC)
frame may be damaged by noise or by another
station transmitting at the same time (collision)
any overlap of frames causes collision
max utilization 18%
6. Slotted ALOHA
time on channel based on uniform slots equal to
frame transmission time
◦ need central clock (or other sync mechanism)
transmission begins at slot boundary
frames either miss or overlap totally
max utilization 37%
both have poor utilization
fail to use fact that propagation time is much
less than frame transmission time
7. CSMA
stations soon know transmission has started
so first listen for clear medium (carrier sense)
if medium idle, transmit
if two stations start at the same instant, collision
◦ wait reasonable time
◦ if no ACK then retransmit
◦ collisions occur occur at leading edge of frame
max utilization depends on propagation time
(medium length) and frame length
8. Nonpersistent CSMA
Nonpersistent CSMA rules:
1. if medium idle, transmit
2. if medium busy, wait amount of time drawn from
probability distribution (retransmission delay) &
retry
random delays reduces probability of
collisions
capacity is wasted because medium will
remain idle following end of transmission
nonpersistent stations are deferential
9. 1-persistent CSMA
1-persistent CSMA avoids idle channel time
1-persistent CSMA rules:
1. if medium idle, transmit;
2. if medium busy, listen until idle; then transmit
immediately
1-persistent stations are selfish
if two or more stations waiting, a collision is
guaranteed
10. P-persistent CSMA
a compromise to try and reduce collisions
and idle time
p-persistent CSMA rules:
1. if medium idle, transmit with probability p, and
delay one time unit with probability (1–p)
2. if medium busy, listen until idle and repeat step
1
3. if transmission is delayed one time unit, repeat
step 1
issue of choosing effective value of p to
avoid instability under heavy load
11. Value of p?
have n stations waiting to send
at end of tx, expected no of stations is np
◦ if np>1 on average there will be a collision
repeated tx attempts mean collisions likely
eventually when all stations trying to send
have continuous collisions hence zero
throughput
thus want np<1 for expected peaks of n
◦ if heavy load expected, p small
◦ but smaller p means stations wait longer
12. CSMA/CD Description
with CSMA, collision occupies
medium for duration of transmission
better if stations listen whilst
transmitting
CSMA/CD rules:
1. if medium idle, transmit
2. if busy, listen for idle, then transmit
3. if collision detected, jam and then cease
transmission
4. after jam, wait random time then retry
14. Which Persistence Algorithm?
IEEE 802.3 uses 1-persistent
both nonpersistent and p-persistent have
performance problems
1-persistent seems more unstable than p-
persistent
◦ because of greed of the stations
◦ but wasted time due to collisions is short
◦ with random backoff unlikely to collide on next
attempt to send
15. Binary Exponential Backoff
for backoff stability, IEEE 802.3 and Ethernet
both use binary exponential backoff
stations repeatedly resend when collide
◦ on first 10 attempts, mean random delay doubled
◦ value then remains same for 6 further attempts
◦ after 16 unsuccessful attempts, station gives up and
reports error
1-persistent algorithm with binary exponential
backoff efficient over wide range of loads
but backoff algorithm has last-in, first-out effect
16. Collision Detection
on baseband bus
◦ collision produces higher signal voltage
◦ collision detected if cable signal greater
than single station signal
◦ signal is attenuated over distance
◦ limit to 500m (10Base5) or 200m
(10Base2)
on twisted pair (star-topology)
◦ activity on more than one port is collision
◦ use special collision presence signal
18. 10Mbps Specification
(Ethernet)
10BASE5 10BASE2 10BASE-T 10BASE-FP
Transmission Coaxial cable (50 Coaxial cable (50 Unshielded twisted 850-nm optical fiber
medium ohm) ohm) pair pair
Signaling Baseband Baseband Baseband Manchester/on-off
technique (Manchester) (Manchester) (Manchester)
Topology Bus Bus Star Star
Maximum segment 500 185 100 500
length (m)
Nodes per segment 100 30 — 33
Cable diameter 10 5 0.4 to 0.6 62.5/125 µm
(mm)
19. 100Mbps Fast Ethernet
100BASE-TX 100BASE-FX 100BASE-T4
Transmission 2 pair, STP 2 pair, Category 2 optical fibers 4 pair, Category
medium 5 UTP 3, 4, or 5 UTP
Signaling MLT-3 MLT-3 4B5B, NRZI 8B6T, NRZ
technique
Data rate 100 Mbps 100 Mbps 100 Mbps 100 Mbps
Maximum 100 m 100 m 100 m 100 m
segment length
Network span 200 m 200 m 400 m 200 m
20. 100BASE-X
uses a unidirectional data rate 100 Mbps over
single twisted pair or optical fiber link
encoding scheme same as FDDI
◦ 4B/5B-NRZI
two physical medium specifications
◦ 100BASE-TX
uses two pairs of twisted-pair cable for tx & rx
STP and Category 5 UTP allowed
MTL-3 signaling scheme is used
◦ 100BASE-FX
uses two optical fiber cables for tx & rx
convert 4B/5B-NRZI code group into optical signals
21. 100BASE-T4
100-Mbps over lower-quality Cat 3 UTP
◦ takes advantage of large installed base
◦ does not transmit continuous signal between packets
◦ useful in battery-powered applications
can not get 100 Mbps on single twisted pair
◦ so data stream split into three separate streams
◦ four twisted pairs used
◦ data transmitted and received using three pairs
◦ two pairs configured for bidirectional transmission
use ternary signaling scheme (8B6T)
23. Full Duplex Operation
traditional Ethernet half duplex
using full-duplex, station can transmit and
receive simultaneously
100-Mbps Ethernet in full-duplex mode, giving a
theoretical transfer rate of 200 Mbps
stations must have full-duplex adapter cards
and must use switching hub
◦ each station constitutes separate collision domain
◦ CSMA/CD algorithm no longer needed
◦ 802.3 MAC frame format used
24. Mixed Configurations
Fast Ethernet supports mixture of existing 10-
Mbps LANs and newer 100-Mbps LANs
supporting older and newer technologies
◦ e.g. 100-Mbps backbone LAN supports 10-Mbps hubs
stations attach to 10-Mbps hubs using 10BASE-T
hubs connected to switching hubs using 100BASE-T
high-capacity workstations and servers attach directly to 10/100
switches
switches connected to 100-Mbps hubs use 100-Mbps links
100-Mbps hubs provide building backbone
connected to router providing connection to WAN
26. Gigabit Ethernet - Differences
carrier extension
◦ at least 4096 bit-times long (512 for
10/100)
frame bursting
not needed if using a switched hub to
provide dedicated media access
28. 10Gbps Ethernet
growing interest in 10Gbps Ethernet
◦ for high-speed backbone use
◦ with future wider deployment
alternative to ATM and other WAN technologies
uniform technology for LAN, MAN, or WAN
advantages of 10Gbps Ethernet
◦ no expensive, bandwidth-consuming conversion
between Ethernet packets and ATM cells
◦ IP and Ethernet together offers QoS and traffic policing
approach ATM
◦ have a variety of standard optical interfaces
31. Fibre Channel - Background
I/O channel
◦ direct point to point or multipoint comms
link
◦ hardware based, high speed, very short
distances
network connection
◦ based on interconnected access points
◦ software based protocol with flow control,
error detection & recovery
◦ for end systems connections
32. Fibre Channel
combines best of both technologies
channel oriented
◦ data type qualifiers for routing frame payload
◦ link level constructs associated with I/O ops
◦ protocol interface specifications to support
existing I/O architectures
network oriented
◦ full multiplexing between multiple destinations
◦ peer to peer connectivity
◦ internetworking to other connection technologies
33. Fibre Channel Requirements
full duplex links with two fibers per link
100 Mbps to 800 Mbps on single line
support distances up to 10 km
small connectors
high-capacity utilization, distance insensitivity
greater connectivity than existing multidrop channels
broad availability
multiple cost/performance levels
carry multiple existing interface command sets for
existing channel and network protocols
36. Fibre Channel Physical Media
800 Mbps 400 Mbps 200 Mbps 100 Mbps
Single mode 10 km 10 km 10 km —
fiber
50-µm 0.5 km 1 km 2 km —
multimode fiber
62.5-µm 175 m 1 km 1 km —
multimode fiber
Video coaxial 50 m 71 m 100 m 100 m
cable
Miniature 14 m 19 m 28 m 42 m
coaxial cable
Shielded twisted 28 m 46 m 57 m 80 m
pair
37. Fibre Channel Fabric
most general supported topology is fabric or
switched topology
◦ arbitrary topology with at least one switch to
interconnect number of end systems
◦ may also consist of switched network
routing transparent to nodes
◦ when data transmitted into fabric, edge switch uses
destination port address to determine location
◦ either deliver frame to node attached to same switch
or transfers frame to adjacent switch
38. Fabric Advantages
scalability of capacity
protocol independent
distance insensitive
switch and transmission link technologies
may change without affecting overall
configuration
burden on nodes minimized
39. Alternative Topologies
Point-to-point topology
◦ only two ports
◦ directly connected, so no routing needed
Arbitrated loop topology
◦ simple, low-cost topology
◦ up to 126 nodes in loop
◦ operates roughly equivalent to token ring
topologies, transmission media, and
data rates may be combined
41. Fibre Channel Prospects
backed by Fibre Channel Association
various interface cards available
widely accepted as peripheral device
interconnect
technically attractive to general high-speed LAN
requirements
must compete with Ethernet and ATM LANs
cost and performance issues will dominate
consideration of competing technologies