B.tech admission in india

B.Tech Admission in India
By:
admission.edhole.com

Composite Beams and Columns

General Provisions
• When determining load effects in members and
connections of a structure with composite
members consider effective sections at the time
each increment of load is applied.
• Properties of the concrete and reinforcing steel
are per ACI 318
• Available strength of members is from either
plastic stress distribution or strain compatibility
• Tensile strength of concrete is assumed to be zero

Plastic Stress Distribution
• Available strength assumes steel has hit yield
stress in either tension or compression, and
the concrete in compression is at 085 f’c
– This method is typically used for regular sections

Strain compatibility method
• Linear strain distribution across the section is
assumed.
• Maximum concrete compressive strain of
0.003 is used
• We use this method in Structures:
Compressive

Encased composite columns
• Cross-sectional area of steel must be at least
1% of total cross-section
• Concrete encasement must be reinforced with
continuous longitudinal bars and lateral
ties/spirals
– Transverse reinforcement ≥ 0.009 in2/in
• Reinforcement ratio must be at least 0.004

Available Compressive Strength
• For axial load encased column, limit case of flexural
buckling
– fc = 0.75 and Wc = 2.00
'
– P0 = nominal elastic compressive strength without length effects
(kips)
– As = area of steel section (in2)
– Asr = area of continuous reinforcing bars (in2)
– Ac = area of concrete (in2)
– sy = yield strength of steel section (ksi)
– syr = yield strength of reinforcement (ksi)
– f’c = concrete compressive strength (ksi)

P0  Ass y  Asrs sr  0.85Ac fc

Elastic buckling strength
Pe 
 2EIeff
KL2
• EIeff = effective rigidity of composite section (kip-in2)
• K = effective length factor
• L = laterally unbraced length of the member (in)


Effective rigidity
• Es = modulus of steel (ksi)
• Ec = modulus of concrete (ksi)
• Is = moment of inertia steel section (in4)
• Isr = moment of inertia reinforcement (in4)
• Ic = moment of inertia concrete (in4)

EIeff  EsIs  0.5EsIsr C1EcIc
C1  0.1 2
As



Ac  As


  0.3

Nominal compressive strength
• If Pe ≥ 0.44 P0
• Else (Pe < 0.44 P0)

 

Pn  P0 0.658
P0
Pe









Pn  0.877Pe

Shear Connectors
• It is necessary to ensure that load is
transferred from the concrete to the steel
• Shear connectors accomplish this
• Resist the shear force between the slab and
beam
• Prevent separation of the slab from the beam

Shear Connectors
• Stud connectors are the most common in U.S.
– Short round steel bar, welded to the beam at one end,
with a head at the other end.
– Diameter from 1⁄2 in. to 1 in. and lengths from 2 to 8
in.
– The ratio of the length to diameter ≥ 4.
– Most commonly used sizes are 3⁄4 in. or 7/8 in. dia.
• Head diameter is 1⁄2 in. larger than stud and the
head thickness is 3/8 in. or 1⁄2 in.

Shear studs
• ASTM-A108, AISI Grades C1010, C1015, C1017 or
C1020 cold-drawn steel with a minimum tensile
strength of 60 ksi and a minimum elongation of 20%
– specified in the AWS Structural Welding Code D1.1-75.
• To prevent premature failure of studs because of
tearing of base metal, the size of a stud not located
over the beam web is limited to 2 1⁄2 times the flange
thickness.
• The strength of stud connectors increases with stud
length up to a length of about four diameters and
remains approximately constant for greater lengths

Equivalent shear force
• V’ = required shear force
• When external force is applied to the steel
section


V'  V 1 
Ass y
P0




• When external force is applied to the concrete
encaseme nt
V'  V


Ass y
P0





Distribution
• Shear connectors that can hold the required
V’ must be distributed along the length for at
least 2.5 times the depth of the encased
column above and below the applied load
• Maximum spacing is 16”
• Connectors must be on at least 2 faces,
symmetrically

Shear Connectors

Additional issues
• At least four longitudinal bars must be used.
• Transverse reinforcement must be spaced at
the lesser of
– 16 longitudinal bar diameters
– 48 tie bar diameters
– Half of the least dimension of the composite
section
• At least 1.5 inches of clear cover is required

Built-up Composite columns
• If the steel section is built from two or more
encased steel shapes, the shapes must be
interconnected
– Lacing
– Tie plates
– Batten plates
– Etc
• To prevent buckling of individual shapes

Shear strength of a connector
'Ec  Ascsu
Qn  0.5Asc fc
• Asc = cross-sectional area of stud (in2)
• Ec = modulus of concrete (ksi)
• su  = tensile strength of connector (ksi)

Girder
Floor beam
L
S

Effective width
b
Yc
tw
tf
bf
tc
hr
d

Shear Connectors Concrete Slab Ribbed steel deck
Steel section

B.tech admission in india

Recommended

Recommended

More Related Content

What's hot

What's hot (20)

Similar to B.tech admission in india

Similar to B.tech admission in india (20)

More from Edhole.com

More from Edhole.com (20)

Recently uploaded

Recently uploaded (20)

B.tech admission in india