WHAT IF IT FINISHES...? - ENVIRONMENTAL STUDIES CBSE-V CBSEBIOLOGY TEACHER
“Fossil fuels are the fuels formed by natural processes such as decomposition of dead and buried organisms. “ Fossil fuels are buried flammable geologic deposits of organic substances such as dead plants, and animals that got deposited under several thousand feet of silt.
These deposits decayed with the passage of time and got converted to natural gas, coal, and petroleum due to the extreme heat and pressure inside the earth’s crust. They are also known as non-renewable sources of energy as it takes a very long time for it to replenish. Types, Formation and Uses of Fossil Fuels
Fossil fuels are of the following types:
Coal
Petroleum
Natural gas
PERFORMANCE ANALYSIS OF HYDROGEN FUELED INTERNAL COMBUSTION ENGINEijsrd.com
In the history of internal combustion engine development, hydrogen has been considered at several phases as a substitute of hydrocarbon-based fuels. Starting from the 70’s, there have been several attempts to convert engines for hydrogen operation. Together with the development in gas injector technology it has become possible to control precisely the injection of hydrogen for safe operation. Here we are using stainless steel plate as electrode in the electrolytic cell, the electrolyte being water and NACL salt. The electrolytic cell we used is a 12V battery case made of plastic. The cross sectional layers are cut such that the stainless steel plate fix in the battery case. The plates are separated by very small distance and the plates are given parallel holes for electron flow to be uniform. The power source to the kit is provided by a 12V and 9Ams battery. We used a transparent tube to supply the hydrogen produced in the kit to the air hose tube of our motor cycle. In order to keep the battery charged we used two 6 Amp diode to power the battery while running. There is a separate switch to power the kit and to protect the battery from getting drained. The stainless steel plates are of 50cm length, 25cm height, 2 millimeter thickness. The battery case can hold up to 5 liters of electrolyte. The use of hydrogen with petrol to power the vehicle has resulted in increase in vehicle mileage, accelerating speed with most important task of reduction in exhaust emission.
WHAT IF IT FINISHES...? - ENVIRONMENTAL STUDIES CBSE-V CBSEBIOLOGY TEACHER
“Fossil fuels are the fuels formed by natural processes such as decomposition of dead and buried organisms. “ Fossil fuels are buried flammable geologic deposits of organic substances such as dead plants, and animals that got deposited under several thousand feet of silt.
These deposits decayed with the passage of time and got converted to natural gas, coal, and petroleum due to the extreme heat and pressure inside the earth’s crust. They are also known as non-renewable sources of energy as it takes a very long time for it to replenish. Types, Formation and Uses of Fossil Fuels
Fossil fuels are of the following types:
Coal
Petroleum
Natural gas
PERFORMANCE ANALYSIS OF HYDROGEN FUELED INTERNAL COMBUSTION ENGINEijsrd.com
In the history of internal combustion engine development, hydrogen has been considered at several phases as a substitute of hydrocarbon-based fuels. Starting from the 70’s, there have been several attempts to convert engines for hydrogen operation. Together with the development in gas injector technology it has become possible to control precisely the injection of hydrogen for safe operation. Here we are using stainless steel plate as electrode in the electrolytic cell, the electrolyte being water and NACL salt. The electrolytic cell we used is a 12V battery case made of plastic. The cross sectional layers are cut such that the stainless steel plate fix in the battery case. The plates are separated by very small distance and the plates are given parallel holes for electron flow to be uniform. The power source to the kit is provided by a 12V and 9Ams battery. We used a transparent tube to supply the hydrogen produced in the kit to the air hose tube of our motor cycle. In order to keep the battery charged we used two 6 Amp diode to power the battery while running. There is a separate switch to power the kit and to protect the battery from getting drained. The stainless steel plates are of 50cm length, 25cm height, 2 millimeter thickness. The battery case can hold up to 5 liters of electrolyte. The use of hydrogen with petrol to power the vehicle has resulted in increase in vehicle mileage, accelerating speed with most important task of reduction in exhaust emission.
What is Bio fuel?
Green Diesel
Bio Diesel
Bio fuel Gasoline
Vegetable Oil
Bio ethers
Ethanol
Bio gas and Syngas
Solid Biofuel
Application Of Biofuel
Q&A on Biogas
SUN is the ultimate source of energy.” Through the ages, the world has known this. The heat and light from this star is the reason for life on our planet. The rains, the forests, the deserts, and our ecosystems.
Electricity:
-> electricity is mechanical power.
->they release stored chemical energy on combustion.
->Electricity used topower vehicles is commonly provided by batteries, but recently fuel cells are also being explored.
battery:
->it is device which is used to store electrical energy.
->in this chemical reactions are converted in to electrical powers
Advantages of electric fuel:
->The advantages of electric fuel/fuel cells are No tailpipe emissions.
->Vehicles using electric fuel demand less
maintenance.
->Electric fuel vehicle have less moving parts
to service and replace.
->Fuel cells vehicles are highly efficient.
->Fuel cells have high power density .
Disadvantages of electric fuel:
-> Batteries may take time in charging .
->Noble metal required for somefuel cells thereby increasing the cost.
->Impurities in the hydrogen can hamper cell
performance.
-> Costly technology
BIOHYDROGEN:
1slide:
->Biohydrogen is 1st generation biofuel and it is produced biologically
->Hydrogen can be produced from a number of different sources, including natural gas,water, methanol etc ..,
->Two methods are generally used to produce hydrogen:
(1) Electrolysis
(2) Synthesis gas production from steam reforming or partial oxidation
2slide:
Electrolysis:
-> 2 H2O(l) → 2 H2(g) + O2(g)
electrolysis of water diagram.......
3 slide:
Synthesis gas production from steam reforming or
partial oxidation:
.
-> C + ½ O2 → CO
-> CO + H2O → CO2 + H2
syntesis diagram.......,.
4slide:
Advantages:
->Hydrogen-air mixture burns nearly10timesfaster than gasoline-air mixture.
->Hydrogen has high self-ignition temperaturebut requires very little energy to ignite it
->.Clean exhaust, produces no CO2.
->As a fuel it is very efficient as there are no losses associated with throttling.
Disadvantages:
There is danger of back fire and induction ignition.
->Though low inexhaust,it produces toxic NOx
->it is diifficult to handle and store,requiring highcapital and running cost.
.
Hydrogen, as a clean, efficient and sustainable energy source, has been accelerated to develop and utilize. Agricultural wastes can be converted into hydrogen to realize high
What is Bio fuel?
Green Diesel
Bio Diesel
Bio fuel Gasoline
Vegetable Oil
Bio ethers
Ethanol
Bio gas and Syngas
Solid Biofuel
Application Of Biofuel
Q&A on Biogas
SUN is the ultimate source of energy.” Through the ages, the world has known this. The heat and light from this star is the reason for life on our planet. The rains, the forests, the deserts, and our ecosystems.
Electricity:
-> electricity is mechanical power.
->they release stored chemical energy on combustion.
->Electricity used topower vehicles is commonly provided by batteries, but recently fuel cells are also being explored.
battery:
->it is device which is used to store electrical energy.
->in this chemical reactions are converted in to electrical powers
Advantages of electric fuel:
->The advantages of electric fuel/fuel cells are No tailpipe emissions.
->Vehicles using electric fuel demand less
maintenance.
->Electric fuel vehicle have less moving parts
to service and replace.
->Fuel cells vehicles are highly efficient.
->Fuel cells have high power density .
Disadvantages of electric fuel:
-> Batteries may take time in charging .
->Noble metal required for somefuel cells thereby increasing the cost.
->Impurities in the hydrogen can hamper cell
performance.
-> Costly technology
BIOHYDROGEN:
1slide:
->Biohydrogen is 1st generation biofuel and it is produced biologically
->Hydrogen can be produced from a number of different sources, including natural gas,water, methanol etc ..,
->Two methods are generally used to produce hydrogen:
(1) Electrolysis
(2) Synthesis gas production from steam reforming or partial oxidation
2slide:
Electrolysis:
-> 2 H2O(l) → 2 H2(g) + O2(g)
electrolysis of water diagram.......
3 slide:
Synthesis gas production from steam reforming or
partial oxidation:
.
-> C + ½ O2 → CO
-> CO + H2O → CO2 + H2
syntesis diagram.......,.
4slide:
Advantages:
->Hydrogen-air mixture burns nearly10timesfaster than gasoline-air mixture.
->Hydrogen has high self-ignition temperaturebut requires very little energy to ignite it
->.Clean exhaust, produces no CO2.
->As a fuel it is very efficient as there are no losses associated with throttling.
Disadvantages:
There is danger of back fire and induction ignition.
->Though low inexhaust,it produces toxic NOx
->it is diifficult to handle and store,requiring highcapital and running cost.
.
Hydrogen, as a clean, efficient and sustainable energy source, has been accelerated to develop and utilize. Agricultural wastes can be converted into hydrogen to realize high
Welcome to TechSoup New Member Orientation and Q&A (May 2024).pdfTechSoup
In this webinar you will learn how your organization can access TechSoup's wide variety of product discount and donation programs. From hardware to software, we'll give you a tour of the tools available to help your nonprofit with productivity, collaboration, financial management, donor tracking, security, and more.
Students, digital devices and success - Andreas Schleicher - 27 May 2024..pptxEduSkills OECD
Andreas Schleicher presents at the OECD webinar ‘Digital devices in schools: detrimental distraction or secret to success?’ on 27 May 2024. The presentation was based on findings from PISA 2022 results and the webinar helped launch the PISA in Focus ‘Managing screen time: How to protect and equip students against distraction’ https://www.oecd-ilibrary.org/education/managing-screen-time_7c225af4-en and the OECD Education Policy Perspective ‘Students, digital devices and success’ can be found here - https://oe.cd/il/5yV
This is a presentation by Dada Robert in a Your Skill Boost masterclass organised by the Excellence Foundation for South Sudan (EFSS) on Saturday, the 25th and Sunday, the 26th of May 2024.
He discussed the concept of quality improvement, emphasizing its applicability to various aspects of life, including personal, project, and program improvements. He defined quality as doing the right thing at the right time in the right way to achieve the best possible results and discussed the concept of the "gap" between what we know and what we do, and how this gap represents the areas we need to improve. He explained the scientific approach to quality improvement, which involves systematic performance analysis, testing and learning, and implementing change ideas. He also highlighted the importance of client focus and a team approach to quality improvement.
The Art Pastor's Guide to Sabbath | Steve ThomasonSteve Thomason
What is the purpose of the Sabbath Law in the Torah. It is interesting to compare how the context of the law shifts from Exodus to Deuteronomy. Who gets to rest, and why?
Read| The latest issue of The Challenger is here! We are thrilled to announce that our school paper has qualified for the NATIONAL SCHOOLS PRESS CONFERENCE (NSPC) 2024. Thank you for your unwavering support and trust. Dive into the stories that made us stand out!
Instructions for Submissions thorugh G- Classroom.pptxJheel Barad
This presentation provides a briefing on how to upload submissions and documents in Google Classroom. It was prepared as part of an orientation for new Sainik School in-service teacher trainees. As a training officer, my goal is to ensure that you are comfortable and proficient with this essential tool for managing assignments and fostering student engagement.
Synthetic Fiber Construction in lab .pptxPavel ( NSTU)
Synthetic fiber production is a fascinating and complex field that blends chemistry, engineering, and environmental science. By understanding these aspects, students can gain a comprehensive view of synthetic fiber production, its impact on society and the environment, and the potential for future innovations. Synthetic fibers play a crucial role in modern society, impacting various aspects of daily life, industry, and the environment. ynthetic fibers are integral to modern life, offering a range of benefits from cost-effectiveness and versatility to innovative applications and performance characteristics. While they pose environmental challenges, ongoing research and development aim to create more sustainable and eco-friendly alternatives. Understanding the importance of synthetic fibers helps in appreciating their role in the economy, industry, and daily life, while also emphasizing the need for sustainable practices and innovation.
Palestine last event orientationfvgnh .pptxRaedMohamed3
An EFL lesson about the current events in Palestine. It is intended to be for intermediate students who wish to increase their listening skills through a short lesson in power point.
1. Alternative fuel
Abstract
Alternative fuels, known as non-
conventional or advanced fuels, are any
materials or substances that can be used as
fuels, other than conventional fuels.
Conventional fuels include: fossil fuels
(petroleum (oil), coal, and natural gas), as
well as nuclear materials such as uranium
and thorium, as well as artificial
radioisotope fuels that are made in nuclear
reactors.
Some well-known alternative fuels include
biodiesel, bioalcohol (methanol, ethanol,
butanol), chemically stored electricity
(batteries and fuel cells), hydrogen, non-
fossil methane, non-fossil natural gas,
vegetable oil, propane, and other biomass
sources.
Background
The main purpose of fuel is to store energy,
which should be in a stable form and can be
easily transported to the place of
production. Almost all fuels are chemical
fuels. The user employs this fuel to
generate heat or perform mechanical work,
such as powering an engine. It may also be
used to generate electricity, which is then
used for heating, lighting, or other
purposes.
Biofuel
Biofuels are also considered a renewable
source. Although renewable energy is used
mostly to generate electricity, it is often
assumed that some form of renewable
energy or a percentage is used to create
alternative fuels.
Biomass
Biomass in the energy production industry
is living and recently dead biological
material which can be used as fuel or for
industrial production.
Algae-based fuels
Algae-based biofuels have been promoted
in the media as a potential panacea to
crude oil-based transportation problems.
Algae could yield more than 2000 gallons of
fuel per acre per year of production. Algae
based fuels are being successfully tested by
the U.S. Navy Algae-based plastics show
potential to reduce waste and the cost per
pound of algae plastic is expected to be
cheaper than traditional plastic prices.
Biodiesel
Biodiesel is made from animal fats or
vegetable oils, renewable resources that
come from plants such as, soybean,
sunflowers, corn, olive, peanut, palm,
coconut, safflower, canola, sesame,
cottonseed, etc. Once these fats or oils are
filtered from their hydrocarbons and then
combined with alcohol like methanol,
biodiesel is brought to life from this
chemical reaction. These raw materials can
either be mixed with pure diesel to make
various proportions, or used alone. Despite
o e’s i ture prefere e, iodiesel ill
release smaller number of pollutants
(carbon monoxide particulates and
hydrocarbons) than conventional diesel,
because biodiesel burns both cleanly and
ore effi ie tl . E e ith regular diesel’s
reduced quantity of sulfur from the ULSD
(ultra-low sulfur diesel) invention, biodiesel
exceeds those levels because it is sulfur-
free.
Alcohol fuels
Methanol and ethanol fuel are primary
sources of energy; they are convenient fuels
2. for storing and transporting energy. These
alcohols can be used in internal combustion
engines as alternative fuels. Butanol has
another advantage: it is the only alcohol-
based motor fuel that can be transported
readily by existing petroleum-product
pipeline networks, instead of only by tanker
trucks and railroad cars.
Ammonia
Ammonia (chemical formula NH3) can be
used as fuel. A small machine can be set up
to create the fuel and it is used where it is
made. Benefits of ammonia include no need
for oil, zero emissions, low cost, and
distributed production reducing transport
and related pollution.
Carbon-neutral and negative fuels
Carbon neutral fuel is synthetic fuel—such
as methane, gasoline, diesel fuel or jet
fuel—produced from renewable or nuclear
energy used to hydrogenate waste carbon
dioxide recycled from power plant flue
exhaust gas or derived from carbonic acid in
seawater. Such fuels are potentially carbon
neutral because they do not result in a net
increase in atmospheric greenhouse gases.
To the extent that carbon neutral fuels
displace fossil fuels, or if they are produced
from waste carbon or seawater carbonic
acid, and their combustion is subject to
carbon capture at the flue or exhaust pipe,
they result in negative carbon dioxide
emission and net carbon dioxide removal
from the atmosphere, and thus constitute a
form of greenhouse gas remediation. Such
carbon neutral and negative fuels can be
produced by the electrolysis of water to
make hydrogen used in the Sabatier
reaction to produce methane which may
then be stored to be burned later in power
plants as synthetic natural gas, transported
by pipeline, truck, or tanker ship, or be used
in gas to liquids processes such as the
Fischer–Tropsch process to make traditional
transportation or heating fuels.
Carbon-neutral fuels have been proposed
for distributed storage for renewable
energy, minimizing problems of wind and
solar intermittency, and enabling
transmission of wind, water, and solar
power through existing natural gas
pipelines. Such renewable fuels could
alleviate the costs and dependency issues of
imported fossil fuels without requiring
either electrification of the vehicle fleet or
conversion to hydrogen or other fuels,
enabling continued compatible and
affordable vehicles. Germany has built a
250-kilowatt synthetic methane plant which
they are scaling up to 10 megawatts. Audi
has constructed a carbon neutral liquefied
natural gas (LNG) plant in Werlte, Germany.
The plant is intended to produce
transportation fuel to offset LNG used in
their A3 Sport back g-ton automobiles, and
can keep 2,800 metric tons of CO2 out of
the environment per year at its initial
capacity.
The least expensive source of carbon for
recycling into fuel is flue-gas emissions from
fossil-fuel combustion, where it can be
extracted for about US $7.50 per ton.
Automobile exhaust gas capture has also
been proposed to be economical but would
require extensive design changes or
retrofitting. Since carbonic acid in seawater
is in chemical equilibrium with atmospheric
carbon dioxide, extraction of carbon from
seawater has been studied. Researchers
have estimated that carbon extraction from
seawater would cost about $50 per ton.
Carbon capture from ambient air is more
costly, at between $600 and $1000 per ton
and is considered impractical for fuel
synthesis or carbon sequestration.
3. HCNG
HCNG (or H2CNG) is a mixture of
compressed natural gas and 4-9 percent
hydrogen by energy.
Liquid nitrogen
Liquid nitrogen is another type of
emissionless fuel.
Compressed air
The air engine is an emission-free piston
engine using compressed air as fuel. Unlike
hydrogen, compressed air is about one-
tenth as expensive as fossil oil, making it an
economically attractive alternative fuel.
Natural Gas Vehicles
Compressed natural gas (CNG) and Liquified
Natural Gas (LNG) are two a cleaner
combusting alternatives to conventional
liquid automobile fuels.
CNG Fuel Types
CNG vehicles can use both renewable CNG
and non-renewable CNG.
Conventional CNG is produced from the
many underground natural gas reserves are
in widespread production worldwide today.
New technologies such as horizontal drilling
and hydraulic fracturing to economically
access unconventional gas resources,
appear to have increased the supply of
natural gas in a fundamental way.
Renewable natural gas or biogas is a
etha e‐ ased gas ith si ilar properties
to natural gas that can be used as
transportation fuel. Present sources of
biogas are mainly landfills, sewage, and
a i al/agri‐ aste. Based o the pro ess
type, biogas can be divided into the
following: Biogas produced by anaerobic
digestion, Landfill gas collected from
landfills, treated to remove trace
contaminants, and Synthetic Natural Gas
(SNG).
Practicality
Around the world, this gas powers more
than 5 million vehicles, and just over
150,000 of these are in the U.S. American
usage is growing at a dramatic rate.
Environmental Analysis
Because natural gas emits little pollutant
when combusted, cleaner air quality has
been measured in urban localities switching
to natural gas vehicles Tailpipe CO2 can be
redu ed 5‐ 5% ompared to gasoline,
diesel. The greatest reductions occur in
medium and heavy duty, light duty and
refuse truck segments.
CO2 reductions of up to 88% are possible by
using biogas.
Similarities to Hydrogen Natural gas, like
hydrogen, is another fuel that burns cleanly;
cleaner than both gasoline and diesel
engines. Also, none of the smog-forming
contaminates are emitted. Hydrogen and
Natural Gas are both lighter than air and
can be mixed together.
Hydrogen
Hydrogen fuel is a zero-emission fuel which
uses electrochemical cells, or combustion in
internal engines, to power vehicles and
electric devices. It is also used in the
propulsion of spacecraft and can potentially
be mass-produced and commercialized for
passenger vehicles and aircraft.
Hydrogen lies in the first group and first
period in the periodic table, i.e. it is the first
element on the periodic table, making it the
lightest element in the universe. Hydrogen
is neither a metal nor a non metal but still is
considered as non metal. It acts as a metal
when compressed to high densities.
4. Since hydrogen gas is so light, it rises in the
atmosphere and is therefore rarely found in
its pure form, H2. In a flame of pure
hydrogen gas, burning in air, the hydrogen
(H2) reacts with oxygen (O2) to form water
(H2O) and releases heat. Other than water,
hydrogen combustion may yield small
amounts of nitrogen oxides.
Combustion heat enables hydrogen to act
as a fuel. Nevertheless, hydrogen is an
energy carrier, like electricity, not an energy
resource. Energy firms must first produce
the hydrogen gas, and that production
induces environmental impacts. Hydrogen
production always requires more energy
than can be retrieved from the gas as a fuel
later on. This is a limitation of the physical
law of the conservation of energy.
H2 Production
SMR Process
Steam reforming, sometimes called Fossil
fuel reforming is a method for producing
hydrogen or other useful products from
hydrocarbon fuels such as natural gas. This
is achieved in a processing device called a
reformer which reacts steam at high
temperature with the fossil fuel. The steam
methane reformer is widely used in industry
to make hydrogen. There is also interest in
the development of much smaller units
based on similar technology to produce
hydrogen as a feedstock for fuel cells.
Small-scale steam reforming units to supply
fuel cells are currently the subject of
research and development, typically
involving the reforming of methanol or
natural gas but other fuels are also being
considered such as propane, gasoline,
autogas, diesel fuel, and ethanol.
Electrolysis of water
Electrolysis of water is the decomposition of
water (H2O) into oxygen (O2) and hydrogen
gas (H2) due to an electric current being
passed through the water.
Equations
In pure water at the negatively charged
cathode, a reduction reaction takes place,
with electrons (e−
) from the cathode being
given to hydrogen cations to form hydrogen
gas (the half reaction balanced with acid):
Reduction at cathode: 2 H+
(aq) + 2e−
→
H2(g)
At the positively charged anode,
an oxidation reaction occurs, generating
oxygen gas and giving electrons to the
anode to complete the circuit:
Oxidation at anode: 2 H2O(l) → O2(g) + 4
H+
(aq) + 4e−
The same half reactions can also be
balanced with base as listed below. Not all
half reactions must be balanced with acid or
base. Many do, like the oxidation or
reduction of water listed here. To add half
reactions they must both be balanced with
either acid or base.
Cathode (reduction): 2 H2O(l) + 2e−
→ H2(g)
+ 2 OH-
(aq)
Anode (oxidation): 4 OH-
(aq) → O2(g) + 2
H2O(l) + 4 e−
Combining either half reaction pair yields
the same overall decomposition of water
into oxygen and hydrogen:
Overall reaction: 2 H2O(l) → H2(g) + O2(g)
The number of hydrogen molecules
produced is thus twice the number of
oxygen molecules. Assuming equal
temperature and pressure for both gases,
the produced hydrogen gas has therefore
twice the volume of the produced oxygen
gas. The number of electrons pushed
through the water is twice the number of
5. generated hydrogen molecules and four
times the number of generated oxygen
molecules.
Techniques
Fundamental demonstration
Two leads, running from the terminals of a
battery, are placed in a cup of water with a
quantity of electrolyte to establish
conductivity in the solution. Using NaCl
(table salt) in an electrolyte solution results
in chlorine gas rather than oxygen due to
a competing half-reaction.With the correct
electrodes and correct electrolyte, such as
baking soda, hydrogen and oxygen gases
will stream from the oppositely
chargedelectrodes. Oxygen will collect at
the positively-charged electrode (anode)
and hydrogen will collect at the negatively-
charged electrode (cathode). Note that
hydrogen is positively charged in the H2O
molecule, so it is "pulled out" at the
negative electrode. (And vice versa for
oxygen.)
Note that an aqueous solution of water
with chloride ions will, when electrolysed,
either result in either OH−
if the
concentration of Cl−
is low, OR in chlorine
gas being preferentially discharged if the
concentration of Cl−
is greater than 25% by
mass in the solution.
Hofmann voltameter
The Hofmann voltameter is often used as a
small-scale electrolytic cell. It consists of
three joined upright cylinders. The inner
cylinder is open at the top to allow the
addition of water and the electrolyte.
A platinum electrode is placed at the
bottom of each of the two side cylinders,
connected to the positive and negative
terminals of a source of electricity. When
current is run through the Hofmann
voltameter, gaseous oxygen forms at
the anode (positive) and gaseous hydrogen
at the cathode(negative). Each gas displaces
water and collects at the top of the two
outer tubes, where it can be drawn off with
a stopcock.
Industrial electrolysis
Many industrial electrolysis cells are very
similar to Hofmann voltameters, with
complex platinum plates or honeycombs as
electrodes. Generally the only time
hydrogen is intentionally produced from
electrolysis is for specific point of use
application such as is the case
with oxyhydrogentorches or when
extremely high hydrogen purity or oxygen is
desired. The vast majority of hydrogen is
produced from hydrocarbons and as a
result contains trace amounts of carbon
monoxide among other impurities. The
carbon monoxide impurity can be
detrimental to various systems including
many fuel cells.
High pressure electrolysis
High pressure electrolysis is the electrolysis
of water with a compressed
hydrogen output around 120-
200 Bar (1740-2900 psi). By pressurising the
hydrogen in the electrolyser the need for an
external hydrogen compressor is
eliminated, the average energy
consumption for internal compression is
around 3%.
High-temperature electrolysis
High-temperature electrolysis (also HTE or
steam electrolysis) is a method currently
being investigated for water electrolysis
with a heat engine. High temperature
electrolysis may be preferable to traditional
room-temperature electrolysis because
some of the energy is supplied as heat,
which is cheaper than electricity, and
because the electrolysis reaction is more
efficient at higher temperatures.
6. Combustive Properties of Hydrogen
• Wide range of flammability
• Low ignition energy
• Small quenching distance
• High auto ignition temperature
• High flame speed at stoichiometric
ratios
• High diffusivity
• Very low density
References
1. "Is Algae Based Biofuel a Great
Green Investment Opportunity".
Green World Investor. 2010-04-06.
Archived from the original on 17
June 2010. Retrieved 2010-07-11.
2. "Navy demonstrates alternative
fuel in riverine vessel". Marine Log.
2010-10-22. Retrieved 2010-07-11.
3. "Can algae-based plastics reduce
our plastic footprint?". Smart
Planet. 2009-10-07. Retrieved 2010-
04-05.
4. Wheeler, Jill (2008). Alternative
Cars. ABDO. p. 21. ISBN 978-1-
59928-803-1.
5. Yirka, Bob (2011-09-05). "Pair claim
they can make ammonia to fuel cars
for just 20 cents per liter".
Physorg.com. Retrieved 2011-09-
12.
6. Zeman, Frank S.; Keith, David W.
(2008). "Carbon neutral
hydrocarbons". Philosophical
Transactions of the Royal Society A
366: 3901–18.
doi:10.1098/rsta.2008.0143.
Retrieved September 7, 2012.
(Review.)
7. Wang, Wei; Wang, Shengping; Ma,
Xinbin; Gong, Jinlong (2011).
"Recent advances in catalytic
hydrogenation of carbon dioxide".
Chemical Society Reviews 40 (7):
3703–27. doi:10.1039/C1CS15008A.
Retrieved September 7, 2012.
(Review.)
8. MacDowell, Niall; et al. (2010). "An
overview of CO2 capture
technologies". Energy and
Environmental Science 3 (11):
1645–69. doi:10.1039/C004106H.
Retrieved September 7, 2012.
(Review.)
9. Eisaman, Matthew D.; et al. (2012).
"CO2 extraction from seawater
using bipolar membrane
electrodialysis". Energy and
Environmental Science 5 (6): 7346–
52. doi:10.1039/C2EE03393C.
Retrieved September 7, 2012.
10. Graves, Christopher; Ebbesen, Sune
D.; Mogensen, Mogens; Lackner,
Klaus S. (2011). "Sustainable
hydrocarbon fuels by recycling CO2
and H2O with renewable or nuclear
energy". Renewable and
Sustainable Energy Reviews 15 (1):
1–23.
doi:10.1016/j.rser.2010.07.014.
Retrieved September 7, 2012.
(Review.)
11. Socolow, Robert; et al. (June 1,
2011). Direct Air Capture of CO2
with Chemicals: A Technology
Assessment for the APS Panel on
Public Affairs (peer reviewed
literature review). American
Physical Society.
http://www.aps.org/policy/reports/
assessments/upload/dac2011.pdf.
Retrieved September 7, 2012.
12. Goeppert, Alain; Czaun, Miklos;
Prakash, G.K. Surya; Olah, George A.
(2012). "Air as the renewable
carbon source of the future: an
overview of CO2 capture from the
atmosphere". Energy and
7. Environmental Science 5 (7): 7833–
53. doi:10.1039/C2EE21586A.
Retrieved September 7, 2012.
(Review.)
13. House, K.Z.; Baclig, A.C.; Ranjan,
M.; van Nierop, E.A.; Wilcox, J.;
Herzog, H.J. (2011). "Economic and
energetic analysis of capturing CO2
from ambient air". Proceedings of
the National Academy of Sciences
of the United States of America 108
(51): 20428–33.
doi:10.1073/pnas.1012253108.
Retrieved September 7, 2012.
(Review.)
14. Lackner, Klaus S.; et al. (2012). "The
urgency of the development of CO2
capture from ambient air".
Proceedings of the National
Academy of Sciences of the United
States of America 109 (33): 13156–
62. Bibcode:2012PNAS..10913156L.
doi:10.1073/pnas.1108765109.
Retrieved September 7, 2012.
15. Pearson, R.J.; Eisaman, M.D.; et al.
(2012). "Energy Storage via Carbon-
Neutral Fuels Made From CO2,
Water, and Renewable Energy".
Proceedings of the IEEE 100 (2):
440–60.
doi:10.1109/JPROC.2011.2168369.
Retrieved September 7, 2012.
(Review.)
16. Pennline, Henry W.; et al. (2010).
"Separation of CO2 from flue gas
using electrochemical cells". Fuel 89
(6): 1307–14.
doi:10.1016/j.fuel.2009.11.036.
Retrieved September 7, 2012.
17. Graves, Christopher; Ebbesen, Sune
D.; Mogensen, Mogens (2011). "Co-
electrolysis of CO2 and H2O in solid
oxide cells: Performance and
durability". Solid State Ionics 192
(1): 398–403.
doi:10.1016/j.ssi.2010.06.014.
Retrieved September 7, 2012.
18. Fraunhofer-Gesellschaft (May 5,
2010). "Storing green electricity as
natural gas". fraunhofer.de.
Retrieved September 9, 2012.
19. Center for Solar Energy and
Hydrogen Research Baden-
Württemberg (2011).
"Verbundprojekt 'Power-to-Gas'"
(in German). zsw-bw.de. Retrieved
September 9, 2012.
20. Center for Solar Energy and
Hydrogen Research (July 24, 2012).
"Bundesumweltminister Altmaier
und Ministerpräsident Kretschmann
zeigen sich beeindruckt von Power-
to-Gas-Anlage des ZSW" (in
German). zsw-bw.de. Retrieved
September 9, 2012.
21. Okulski, Travis (June 26, 2012).
"Audi's Carbon Neutral E-Gas Is Real
And They're Actually Making It".
Jalopnik (Gawker Media). Retrieved
29 July 2013.
22. Rousseau, Steve (June 25, 2013).
"Audi's New E-Gas Plant Will Make
Carbon-Neutral Fuel". Popular
Mechanics. Retrieved 29 July 2013.