This document summarizes a study that analyzed the structural performance of a go-kart chassis made from different materials under various impact conditions using finite element analysis. The chassis was designed in CAD software and then simulated in ANSYS for front, side, and rear impacts using four steel materials: AISI 1018, AISI 1026, AISI 4130, and AISI 1020. The simulations calculated stress levels and deformations. Results showed the factor of safety for each material and impact scenario, identifying designs that were safe or at risk of failure based on exceeding the material's yield strength. AISI 4130 generally had the highest factors of safety, suggesting it could best withstand the forces experienced during impacts
Design and analysis of an electric karteSAT Journals
Abstract This paper presents the design and analysis of an electric motor powered kart. The main aim of this paper is to reduce the usage of organic fuel powered vehicles and to design a vehicle which works efficiently in the emerging electric vehicle sector. In order to maintain the speed levels of the kart, seamless decision was made in motor selection. Alternate materials have been applied in the kart to reduce both static and dynamic forces in pursuance of improving the efficiency and performance of the kart. Detailed design of subsystems like chassis frame, steering system, electrical power train and braking mechanism has been done effectively. The main focus of the frame design was on the stability of the kart and safety of the driver. The CAD model of the kart was done in CREO 2.0. Aluminium alloy 6063 has been employed for the frame to reduce the overall weight. To check the feasibility of the frame design, finite element analysis has been done using ANSYS 14.5. The results obtained showed that the frame design was safe under maximal impact load conditions. Weight reduction was a major concern and hence linkage type steering was selected for the kart. Motor, the heart of the electric vehicle was selected and installed in such a way that it can perform well for an extended run time. PMDC motor was selected in this case. Speed control of the kart was done using a voltage controller. The kart is provided with a timing belt drive to achieve maximum efficiency in transmission of power from the motor to the wheels. Hydraulic disc brakes were provided for smooth and effective braking under both dry and wet conditions. Slick tires are used to provide more traction. Design calculations were carried out and optimum results were obtained. An extensive market survey was also done on frame material, brakes, motor, transmission system for cost and availability. International standards were followed throughout the design process. Keywords: Stability, Frame, Finite Element Analysis, PMDC Motor, Timing belt
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
Design and Analysis of Go Kart Chassis for Front, Side and Rear Impactijtsrd
This paper deals with Go kart chassis building with the help of modelling software CATIA V15 and analysis of the same for front, side and rear impact. The cassis has been designed for light weight profile and engine mounting of capacity 135cc. The go kart vehicle is meant for participation in various Go kart event organized all over the India. The preliminary test for these events is checking of 3 D model of the chassis frame and analysis of the same chassis frame under front, side and rear impact. During collision the chassis is under impact loading conditions so it has to be thoroughly analyzed for impact loads. The studies found below shades some light on how the chassis behaves under impact loading conditions. Chassis is made up of a tubular cross section pipe, fabricated assembly of EN8 grade and a few other grades. In this kart, we have used EN8 class tube with 1 inch diameter and 1.5 mm wall thickness. The results obtained for permissible stresses, Factor of safety and deformation are found to be well within range. This makes the chassis suitable for Go kart events. The main criteria that has been focused here is maximum deformation and stress. The stresses should be well within Von mises stress range and so as the Factor of safety. After analysis, both are found to be well within range. Chetan Mahatme | Pratik Lande | Surendra Nagpure | Abhishek Pawar | Nikhil Kharabe ""Design and Analysis of Go-Kart Chassis for Front, Side and Rear Impact"" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-3 , April 2019, URL: https://www.ijtsrd.com/papers/ijtsrd22973.pdf
Paper URL: https://www.ijtsrd.com/engineering/mechanical-engineering/22973/design-and-analysis-of-go-kart-chassis-for-front-side-and-rear-impact/chetan-mahatme
Design analysis of the roll cage for all terrain vehicleeSAT Journals
Abstract We have tried to design an all terrain vehicle that meets international standards and is also cost effective at the same time. We have focused on every point of roll cage to improve the performance of vehicle without failure of roll cage. We began the task of designing by conducting extensive research of ATV roll cage through finite element analysis. A roll cage is a skeleton of an ATV. The roll cage not only forms the structural base but also a 3-D shell surrounding the occupant which protects the occupant in case of impact and roll over incidents. The roll cage also adds to the aesthetics of a vehicle. The design and development comprises of material selection, chassis and frame design, cross section determination, determining strength requirements of roll cage, stress analysis and simulations to test the ATV against failure. Keywords: Roll cage, material, finite element analysis, strength
Engine is one of the most significant component of road vehicles. High performance vehicles have their
engine supported by bracket. The engine mounting plays an important role in reducing the noise and vibrations, improving the
comfort and work environment of a vehicle. The present work deals with design modification of engine mounting bracket.
Modelling work has been carried out with commercial desktop CAD software and analyzed the modal performance with
Analysis software. Ribs has been adopted to the existing mounting bracket for its better performance structural, thermal and
modal analysis has been carried out with analysis software. Aluminium alloy, aluminium silicon carbide and magnesium alloy
are considered as the different materials of mounting bracket. Based on the analysis it is found that the aluminium silicon
carbide is superior suited for the modified V6 engine mounting bracket.
Finite Element Analysis of Fire Truck Chassis for Steel and Carbon Fiber Mate...IJERA Editor
Chassis is the foremost component of an automobile that acts as the frame to support the vehicle body. Hence the frame ought to be very rigid and robust enough to resist shocks vibrations and stresses acting on a moving vehicle. Steel in its numerous forms is commonly used material for producing chassis and overtime alumimium has acquired its use. However, in this study traditional materials are replaced with ultra light weight carbon fiber materials. High strength and low weight of carbon fibers makes it ideal for manufacturing automotive chassis. This paper depicts the modal and static structural analysis of TATA 407 fire truck chassis frame for steel as well as carbon fibers. From the analyzed results, stress, strain and total deformation values were compared for both the materials. Since it is easy to analyze structural systems by finite element method, the chassis is modified using PRO-E and the Finite Element Analysis is performed on ANSYS workbench.
Design and analysis of an electric karteSAT Journals
Abstract This paper presents the design and analysis of an electric motor powered kart. The main aim of this paper is to reduce the usage of organic fuel powered vehicles and to design a vehicle which works efficiently in the emerging electric vehicle sector. In order to maintain the speed levels of the kart, seamless decision was made in motor selection. Alternate materials have been applied in the kart to reduce both static and dynamic forces in pursuance of improving the efficiency and performance of the kart. Detailed design of subsystems like chassis frame, steering system, electrical power train and braking mechanism has been done effectively. The main focus of the frame design was on the stability of the kart and safety of the driver. The CAD model of the kart was done in CREO 2.0. Aluminium alloy 6063 has been employed for the frame to reduce the overall weight. To check the feasibility of the frame design, finite element analysis has been done using ANSYS 14.5. The results obtained showed that the frame design was safe under maximal impact load conditions. Weight reduction was a major concern and hence linkage type steering was selected for the kart. Motor, the heart of the electric vehicle was selected and installed in such a way that it can perform well for an extended run time. PMDC motor was selected in this case. Speed control of the kart was done using a voltage controller. The kart is provided with a timing belt drive to achieve maximum efficiency in transmission of power from the motor to the wheels. Hydraulic disc brakes were provided for smooth and effective braking under both dry and wet conditions. Slick tires are used to provide more traction. Design calculations were carried out and optimum results were obtained. An extensive market survey was also done on frame material, brakes, motor, transmission system for cost and availability. International standards were followed throughout the design process. Keywords: Stability, Frame, Finite Element Analysis, PMDC Motor, Timing belt
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
Design and Analysis of Go Kart Chassis for Front, Side and Rear Impactijtsrd
This paper deals with Go kart chassis building with the help of modelling software CATIA V15 and analysis of the same for front, side and rear impact. The cassis has been designed for light weight profile and engine mounting of capacity 135cc. The go kart vehicle is meant for participation in various Go kart event organized all over the India. The preliminary test for these events is checking of 3 D model of the chassis frame and analysis of the same chassis frame under front, side and rear impact. During collision the chassis is under impact loading conditions so it has to be thoroughly analyzed for impact loads. The studies found below shades some light on how the chassis behaves under impact loading conditions. Chassis is made up of a tubular cross section pipe, fabricated assembly of EN8 grade and a few other grades. In this kart, we have used EN8 class tube with 1 inch diameter and 1.5 mm wall thickness. The results obtained for permissible stresses, Factor of safety and deformation are found to be well within range. This makes the chassis suitable for Go kart events. The main criteria that has been focused here is maximum deformation and stress. The stresses should be well within Von mises stress range and so as the Factor of safety. After analysis, both are found to be well within range. Chetan Mahatme | Pratik Lande | Surendra Nagpure | Abhishek Pawar | Nikhil Kharabe ""Design and Analysis of Go-Kart Chassis for Front, Side and Rear Impact"" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-3 , April 2019, URL: https://www.ijtsrd.com/papers/ijtsrd22973.pdf
Paper URL: https://www.ijtsrd.com/engineering/mechanical-engineering/22973/design-and-analysis-of-go-kart-chassis-for-front-side-and-rear-impact/chetan-mahatme
Design analysis of the roll cage for all terrain vehicleeSAT Journals
Abstract We have tried to design an all terrain vehicle that meets international standards and is also cost effective at the same time. We have focused on every point of roll cage to improve the performance of vehicle without failure of roll cage. We began the task of designing by conducting extensive research of ATV roll cage through finite element analysis. A roll cage is a skeleton of an ATV. The roll cage not only forms the structural base but also a 3-D shell surrounding the occupant which protects the occupant in case of impact and roll over incidents. The roll cage also adds to the aesthetics of a vehicle. The design and development comprises of material selection, chassis and frame design, cross section determination, determining strength requirements of roll cage, stress analysis and simulations to test the ATV against failure. Keywords: Roll cage, material, finite element analysis, strength
Engine is one of the most significant component of road vehicles. High performance vehicles have their
engine supported by bracket. The engine mounting plays an important role in reducing the noise and vibrations, improving the
comfort and work environment of a vehicle. The present work deals with design modification of engine mounting bracket.
Modelling work has been carried out with commercial desktop CAD software and analyzed the modal performance with
Analysis software. Ribs has been adopted to the existing mounting bracket for its better performance structural, thermal and
modal analysis has been carried out with analysis software. Aluminium alloy, aluminium silicon carbide and magnesium alloy
are considered as the different materials of mounting bracket. Based on the analysis it is found that the aluminium silicon
carbide is superior suited for the modified V6 engine mounting bracket.
Finite Element Analysis of Fire Truck Chassis for Steel and Carbon Fiber Mate...IJERA Editor
Chassis is the foremost component of an automobile that acts as the frame to support the vehicle body. Hence the frame ought to be very rigid and robust enough to resist shocks vibrations and stresses acting on a moving vehicle. Steel in its numerous forms is commonly used material for producing chassis and overtime alumimium has acquired its use. However, in this study traditional materials are replaced with ultra light weight carbon fiber materials. High strength and low weight of carbon fibers makes it ideal for manufacturing automotive chassis. This paper depicts the modal and static structural analysis of TATA 407 fire truck chassis frame for steel as well as carbon fibers. From the analyzed results, stress, strain and total deformation values were compared for both the materials. Since it is easy to analyze structural systems by finite element method, the chassis is modified using PRO-E and the Finite Element Analysis is performed on ANSYS workbench.
Similar to Structural Analysis of Go-kart Chassis using different materials to find the suitable material for the given model (20)
Forklift Classes Overview by Intella PartsIntella Parts
Discover the different forklift classes and their specific applications. Learn how to choose the right forklift for your needs to ensure safety, efficiency, and compliance in your operations.
For more technical information, visit our website https://intellaparts.com
Event Management System Vb Net Project Report.pdfKamal Acharya
In present era, the scopes of information technology growing with a very fast .We do not see any are untouched from this industry. The scope of information technology has become wider includes: Business and industry. Household Business, Communication, Education, Entertainment, Science, Medicine, Engineering, Distance Learning, Weather Forecasting. Carrier Searching and so on.
My project named “Event Management System” is software that store and maintained all events coordinated in college. It also helpful to print related reports. My project will help to record the events coordinated by faculties with their Name, Event subject, date & details in an efficient & effective ways.
In my system we have to make a system by which a user can record all events coordinated by a particular faculty. In our proposed system some more featured are added which differs it from the existing system such as security.
Quality defects in TMT Bars, Possible causes and Potential Solutions.PrashantGoswami42
Maintaining high-quality standards in the production of TMT bars is crucial for ensuring structural integrity in construction. Addressing common defects through careful monitoring, standardized processes, and advanced technology can significantly improve the quality of TMT bars. Continuous training and adherence to quality control measures will also play a pivotal role in minimizing these defects.
Democratizing Fuzzing at Scale by Abhishek Aryaabh.arya
Presented at NUS: Fuzzing and Software Security Summer School 2024
This keynote talks about the democratization of fuzzing at scale, highlighting the collaboration between open source communities, academia, and industry to advance the field of fuzzing. It delves into the history of fuzzing, the development of scalable fuzzing platforms, and the empowerment of community-driven research. The talk will further discuss recent advancements leveraging AI/ML and offer insights into the future evolution of the fuzzing landscape.
Automobile Management System Project Report.pdfKamal Acharya
The proposed project is developed to manage the automobile in the automobile dealer company. The main module in this project is login, automobile management, customer management, sales, complaints and reports. The first module is the login. The automobile showroom owner should login to the project for usage. The username and password are verified and if it is correct, next form opens. If the username and password are not correct, it shows the error message.
When a customer search for a automobile, if the automobile is available, they will be taken to a page that shows the details of the automobile including automobile name, automobile ID, quantity, price etc. “Automobile Management System” is useful for maintaining automobiles, customers effectively and hence helps for establishing good relation between customer and automobile organization. It contains various customized modules for effectively maintaining automobiles and stock information accurately and safely.
When the automobile is sold to the customer, stock will be reduced automatically. When a new purchase is made, stock will be increased automatically. While selecting automobiles for sale, the proposed software will automatically check for total number of available stock of that particular item, if the total stock of that particular item is less than 5, software will notify the user to purchase the particular item.
Also when the user tries to sale items which are not in stock, the system will prompt the user that the stock is not enough. Customers of this system can search for a automobile; can purchase a automobile easily by selecting fast. On the other hand the stock of automobiles can be maintained perfectly by the automobile shop manager overcoming the drawbacks of existing system.
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.